Internet Engineering Task Force                              Brian Weis
INTERNET-DRAFT                                            Cisco Systems
Document: draft-ietf-msec-ipsec-signatures-06.txt            June, 2005
Expires: December, 2005

             The Use of RSA/SHA-1 Signatures within ESP and AH

Status of this Memo

   By submitting this Internet-Draft, each author represents that
   any applicable patent or other IPR claims of which he or she is
   aware have been or will be disclosed, and any of which he or she
   becomes aware will be disclosed, in accordance with Section 6 of
   BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
        http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
        http://www.ietf.org/shadow.html.

Abstract

   This memo describes the use of the RSA Digital Signature algorithm as
   an authentication algorithm within the revised IP Encapsulating
   Security Payload (ESP) as described in RFC XXXX and the revised IP
   Authentication Header (AH) as described in RFC YYYY. The use of a
   digital signature algorithm, such as RSA, provides data origin
   authentication in applications when a secret key method (e.g., HMAC)
   does not provide this property. One example is the use of ESP and AH
   to authenticate the sender of an IP multicast packet.

       -- Note to RFC Editor:  Please replace RFC XXXX with the RFC
       -- number that is assigned to draft-ietf-ipsec-esp-v3 and
       -- replace RFC YYYY with the RFC number assigned to
       -- draft-ietf-ipsec-rfc2402bis. Please also modify normative
       -- references [ESP] and [AH] that point to these drafts with
       -- their respective RFC numbers. Lastly, informative references
       -- [IKEV2] and [AES-GCM] should be changed to their assigned
       -- RFC numbers, assuming they are published before this
       -- document.




   Weis                 Expires December, 2005                [Page 1]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


Table of Contents

1.0 Introduction.......................................................2
2.0 Algorithm and Mode.................................................3
  2.1 Key size discussion..............................................4
3.0 Performance........................................................5
4.0 Interaction with the ESP Cipher Mechanism..........................6
5.0 Key Management Considerations......................................6
6.0 Security Considerations............................................6
  6.1 Eavesdropping....................................................7
  6.2 Replay...........................................................7
  6.3 Message Insertion................................................7
  6.4 Deletion.........................................................7
  6.5 Modification.....................................................7
  6.6 Man in the middle................................................7
  6.7 Denial of Service................................................8
7.0 IANA Considerations................................................8
8.0 Acknowledgements...................................................9
9.0 References.........................................................9
  9.1 Normative References.............................................9
  9.2 Informative References..........................................10
Author's Address......................................................10
Full Copyright Statement..............................................10
Intellectual Property.................................................11

1.0 Introduction

   Encapsulating Security Payload  (ESP) [ESP] and Authentication Header
   (AH) [AH] headers can be used to protect both unicast traffic and
   group (e.g., IPv4 and IPv6 multicast) traffic. When unicast traffic
   is protected between a pair of entities, HMAC transforms (such as
   [HMAC-SHA]) are sufficient to prove data origin authentication. An
   HMAC is sufficient protection in that scenario because only the two
   entities involved in the communication have access to the key, and
   proof-of-possession of the key in the HMAC construct authenticates
   the sender. However when ESP and AH authenticate group traffic, this
   property no longer holds because all group members share the single
   HMAC key. In the group case the identity of the sender is not
   uniquely established, since any of the key holders has the ability to
   form the HMAC transform. Although the HMAC transform establishes a
   group-level security property, data origin authentication is not
   achieved.

   Some group applications require true data origin authentication,
   where one group member cannot successfully impersonate another group
   member. The use of asymmetric digital signature algorithms, such as
   RSA, can provide true data origin authentication.



   Weis                 Expires December, 2005                [Page 2]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


   With asymmetric algorithms, the sender generates a pair of keys, one
   of which is never shared (called the "private key") and one of which
   is distributed to other group members (called the "public key"). When
   the private key is used to sign the output of a cryptographic hash
   algorithm, the result is called a "digital signature". A receiver of
   the digital signature uses the public key, the signature value, and
   an independently computed hash to determine whether or not the
   claimed origin of the packet is correct.

   This memo describes how RSA digital signatures can be applied as an
   ESP and AH authentication mechanism to provide data origin
   authentication.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
   NOT","SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in
   this document are to be interpreted as described in [RFC2119].

2.0 Algorithm and Mode

   The RSA Public Key Algorithm [RSA] is a widely deployed public key
   algorithm commonly used for digital signatures. Compared to other
   public key algorithms, signature verification is relatively
   efficient. This property is useful for groups where receivers may
   have limited processing capabilities. The RSA algorithm is commonly
   supported in hardware.

   Two digital signatures encoding methods are supported in [RSA].
   RSASSA-PKCS1-v1_5 MUST be supported by a conforming implementation.
   RSASSA-PSS is generally believed to be more secure, but at the time
   of this writing is not ubiquitous. RSASSA-PSS SHOULD be used whenever
   it is available. SHA-1 MUST be used as the signature hash algorithm
   used by the RSA digital signature algorithm.

   When specified for ESP, the ICV is equal in size to the RSA modulus,
   unless the RSA modulus is not a multiple of 8 bits. In this case, the
   ICV MUST be prepended with between 1 and 7 bits set to zero such that
   the ICV is a multiple of 8 bits. This specification matches the
   output S [RSA, Section 8.1.1] (RSASSA-PSS) and [RSA, Section
   8.2.1](RSASSA-PKCS1-v1_5) when the RSA modulus is not a multiple of 8
   bits. No implicit ESP ICV Padding bits are necessary.

   When specified for AH, the ICV is equal in size of the RSA modulus,
   unless the RSA modulus is not a multiple of 32 bits (IPv4) or 64 bits
   (IPv6) [AH, Section 2.6]. In this case, explicit ICV Padding bits are
   necessary to create a suitably sized ICV [AH, Section 3.3.3.2.1].

   The distribution mechanism of the RSA public key and its replacement
   interval are a group policy matter. The use of an ephemeral key pair
   with a lifetime of the ESP or AH SA is RECOMMENDED. This recommended
   policy reduces the exposure of the RSA private key to the lifetime of
   the data being signed by the private key. Also, this obviates the
   need to revoke or transmit the validity period of the key pair.

   Weis                 Expires December, 2005                [Page 3]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005



   Digital signature generation is performed as described in [RSA,
   Section 8.1.1] (RSASSA-PSS) and [RSA, Section 8.2.1](RSASSA-PKCS1-
   v1_5). The authenticated portion of the AH or ESP packet ([AH,
   Section 3.3.3], [ESP, Section 3.3.2]) is used as the message M, which
   is passed to the signature generation function. The signer's RSA
   private key is passed as K. Summarizing, the signature generation
   process computes a SHA-1 hash of the authenticated packet bytes,
   signs the SHA-1 hash using the private key, and encodes the result
   with the specified RSA encoding type. This process results in a value
   S, which is known as the ICV in AH and ESP.

   Digital signature verification is performed as described in [RSA,
   Section 8.1.2] (RSASSA-PSS) and [RSA, Section 8.2.2](RSASSA-PKCS1-
   v1_5). Upon receipt, the ICV is passed to the verification function
   as S. The authenticated portion of the AH or ESP packet is used as
   the message M, and the RSA public key is passed as (n, e). In
   summary, the verification function computes a SHA-1 hash of the
   authenticated packet bytes, decrypts the SHA-1 hash in the ICV, and
   validates that the appropriate encoding was applied and was correct.
   The two SHA-1 hashes are compared, and if they are identical the
   validation is successful.


2.1 Key size discussion

   The choice of RSA modulus size must be made carefully. If too small
   of a modulus size is chosen, an attacker may be able to reconstruct
   the private key used to sign packets before the key is no longer used
   by the sender to sign packets. This order of events may result in the
   data origin authentication property being compromised. However,
   choosing a modulus size larger than necessary will result in an
   unnecessarily high cost of CPU cycles for the sender and all
   receivers of the packet.

   A conforming implementation MUST support a modulus size of 1024 bits.

   Recent guidance [TWIRL, RSA-TR] on key sizes make estimates as to the
   amount of effort an attacker would need to expend in order to
   reconstruct an RSA private key. Table 1 summarizes the maximum length
   of time that selected modulus sizes should be used. Note that these
   recommendations are based on factors such as the cost of processing
   and memory, as well as cryptographic analysis methods, which were
   current at the time these documents were published. As those factors
   change, choices of key lifetimes should take them into account.








   Weis                 Expires December, 2005                [Page 4]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


                    Number of     Recommended Maximum
                   Modulus Bits         Lifetime
                   ------------    -------------------
                       768               1 week
                       1024              1 year

             Table 1. RSA Key Use Lifetime Recommendations


3.0 Performance

   The RSA asymmetric key algorithm is very costly in terms of
   processing time compared to the HMAC algorithms. However, processing
   cost is decreasing over time. Faster general-purpose processors are
   being deployed, faster software implementations are being developed,
   and hardware acceleration support for the algorithm is becoming more
   prevalent.

   Care should be taken that RSA signatures are not used for
   applications when potential receivers are known to lack sufficient
   processing power to verify the signature. It is also important to use
   this scheme judiciously when any receiver may be battery powered.

   The RSA asymmetric key algorithm is best suited to protect network
   traffic for which:

    o The sender has a substantial amount of processing power, and

    o The network traffic is small enough that adding a relatively large
      authentication tag (in the range of 62 to 256 bytes) does not
      cause packet fragmentation.

   RSA key pair generation and signing are substantially more expensive
   operations than signature verification, but these are isolated to the
   sender.

   The size of the RSA modulus affects the processing required to create
   and verify RSA digital signatures. Care should be taken to determine
   the size of modulus needed for the application.  Smaller modulus
   sizes may be chosen as long as the network traffic protected by the
   private key flows for less time than it is estimated that an attacker
   would take to discover the private key. This lifetime is considerably
   smaller than most public key applications that store the signed data
   for a period of time. But since the digital signature is used only
   for sender verification purposes, a modulus that is considered weak
   in another context may be satisfactory.

   The size of the RSA public exponent can affect the processing
   required to verify RSA digital signatures. Low-exponent RSA
   signatures may result in a lower verification processing cost. At the
   time of this writing, no attacks are known against low-exponent RSA


   Weis                 Expires December, 2005                [Page 5]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


   signatures that would allow an attacker to create a valid signature
   using the RSAES-OAEP raw RSA scheme.

   The addition of a digital signature as an authentication tag adds a
   significant number of bytes to the packet. This increases the
   likelihood that the packet encapsulated in ESP or AH may be
   fragmented.

4.0 Interaction with the ESP Cipher Mechanism

   The RSA signatures algorithm cannot be used with an ESP Combined Mode
   algorithm that includes an explicit ICV. The Combined Mode algorithm
   will add the ESP ICV field, which does not allow use of a separate
   authentication algorithm to add the ESP ICV field. One example of
   such an algorithm is the ESP Galois/Counter Mode algorithm [AES-GCM].

5.0 Key Management Considerations

   Key management mechanisms negotiating the use of RSA Signatures MUST
   include the length of the RSA modulus during policy negotiation using
   the Authentication Key Length SA Attribute. This gives a device the
   opportunity to decline use of the algorithm. This is especially
   important for devices with constrained processors that might not be
   able to verify signatures using larger key sizes.

   Key management mechanisms negotiating the use of RSA Signatures also
   MUST include the encoding method during policy negotiation using the
   Signature Encoding Algorithm SA Attribute.

   A receiver must have the RSA public key in order to verify integrity
   of the packet. When used with a group key management system (e.g.,
   RFC 3547 [GDOI]), the public key SHOULD be sent as part of the key
   download policy. If the group has multiple senders, the public key of
   each sender SHOULD be sent as part of the key download policy.

   Use of this transform to obtain data origin authentication for
   pairwise SAs is NOT RECOMMENDED. In the case of pairwise SAs (such as
   negotiated by the Internet Key Exchange [IKEv2]), data origin
   authentication can be achieved with an HMAC transform.  Because the
   performance impact of an RSA signature is typically greater than an
   HMAC, the value of using this transform for a pairwise connection is
   limited.

6.0 Security Considerations

   This document provides a method of authentication for ESP and AH
   using digital signatures. This feature provides the following
   protections:

    o Message modification integrity. The digital signature allows the
      receiver of the message to verify that it was exactly the same as
      when the sender signed it.

   Weis                 Expires December, 2005                [Page 6]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005



    o Host authentication. The asymmetric nature of the RSA public key
      algorithm allows the sender to be uniquely verified, even when the
      message is sent to a group.

   Non-repudiation is not claimed as a property of this transform.  At
   times, the property of non-repudiation may be applied to digital
   signatures on application level objects (e.g., electronic mail).
   However, this document describes a means of authenticating network
   level objects (i.e., IP packets), which are ephemeral and not
   directly correlated to any application. Non-repudiation is not
   applicable to network level objects (i.e., IP packets).

   A number of attacks are suggested by [RFC3552]. The following
   sections describe the risks those attacks present when RSA signatures
   are used for ESP and AH packet authentication.

6.1 Eavesdropping

   This document does not address confidentiality. That function, if
   desired, must be addressed by an ESP cipher that is used with the RSA
   Signatures authentication method. The RSA signature itself does not
   need to be protected from an eavesdropper.

6.2 Replay

   This document does not address replay attacks. That function, if
   desired, is addressed through use of ESP and AH sequence numbers as
   defined in [ESP] and [AH].

6.3 Message Insertion

   This document directly addresses message insertion attacks. Inserted
   messages will fail authentication and be dropped by the receiver.

6.4 Deletion

   This document does not address deletion attacks. It is only concerned
   with validating the legitimacy of messages that are not deleted.

6.5 Modification

   This document directly addresses message modification attacks.
   Modified messages will fail authentication and be dropped by the
   receiver.

6.6 Man in the middle

   As long as a receiver is given the sender RSA public key in a trusted
   manner (e.g., by a key management protocol), it will be able to
   verify that the digital signature is correct. A man in the middle


   Weis                 Expires December, 2005                [Page 7]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


   will not be able to spoof the actual sender unless it acquires the
   RSA private key through some means.

   The RSA modulus size must be chosen carefully to ensure that the time
   a man in the middle needs to determine the RSA private key through
   cryptanalysis is longer than the amount of time that packets are
   signed with that private key.

6.7 Denial of Service

   According to IPsec processing rules, a receiver of an ESP and AH
   packet begins by looking up the Security Association in the SADB. If
   one is found, the ESP or AH sequence number in the packet is
   verified. No further processing will be applied to packets with an
   invalid sequence number.

   An attacker that sends an ESP or AH packet matching a valid SA on the
   system and also having a valid sequence number will cause the
   receiver to perform the ESP or AH authentication step. Because the
   process of verifying an RSA digital signature consumes relatively
   large amounts of processing, many such packets could lead to a denial
   of service attack on the receiver.

   If the message was sent to an IPv4 or IPv6 multicast group all group
   members that received the packet would be under attack
   simultaneously.

   This attack can be mitigated against most attackers by encapsulating
   ESP or AH using an RSA Signature for authentication within ESP or AH
   using an HMAC transform for authentication. In this case, the HMAC
   transform would be validated first, and as long as the attacker does
   not possess the HMAC key no digital signatures would be evaluated on
   the attacker packets. However, if the attacker does possess the HMAC
   key (e.g., they are a legitimate member of the group using the SA)
   then the DoS attack cannot be mitigated.

7.0 IANA Considerations

   An assigned number is required in the "IPSec Authentication
   Algorithm" name space in the ISAKMP registry [ISAKMP-REG]. The
   mnemonic should be "SIG-RSA".

   An assigned number is also required in the "IPSEC AH Transform
   Identifiers" name space in the ISAKMP registry. Its mnemonic should
   be "AH-RSA".

   A new "IPSEC Security Association Attribute" is required in the
   ISAKMP registry to pass the RSA modulus size. The attribute class
   should be called "Authentication Key Length", and it should a
   Variable type.



   Weis                 Expires December, 2005                [Page 8]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


   A second "IPSEC Security Association Attribute" is required in the
   ISAKMP registry to pass the RSA signature encoding type. The
   attribute class should be called "Signature Encoding Algorithm", and
   it should be a Basic type. The following rules apply to define the
   values of the attribute:

                 Name                Value
                 ----                -----
                 Reserved            0
                 RSASSA-PKCS1-v1_5   1
                 RSASSA-PSS          2

   Values 3-61439 are reserved to IANA. New values MUST be added due to
   a Standards Action as defined in [RFC2434]. Values 61440-65535 are
   for private use and may be allocated by implementations for their own
   purposes.

8.0 Acknowledgements

   Scott Fluhrer and David McGrew provided advice regarding applicable
   key sizes. Scott Fluhrer also provided advice regarding key
   lifetimes. Ian Jackson, Steve Kent, and Ran Canetti provided many
   helpful comments. Sam Hartman, Russ Housley, and Lakshminth Dondeti
   provided valuable guidance in the development of this document.

9.0 References

9.1 Normative References

   [AH] Kent, S., "IP Authentication Header", draft-ietf-ipsec-
   rfc2402bis-10.txt, December 2004.

   [ESP] Kent, S., "IP Encapsulating Security Payload (ESP)", draft-
   ietf-ipsec-esp-v3-09.txt, September2004.

   [ISAKMP-REG] http://www.iana.org/assignments/isakmp-registry

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
   Requirement Level", BCP 14, RFC 2119, March 1997.

   [RFC3552] E. Rescorla, et. al., "Guidelines for Writing RFC Text on
   Security Considerations", RFC 3552, July 2003.

   [RSA] Jonsson, J., B. Kaliski,  "Public-Key Cryptography Standard
   (PKCS) #1: RSA Cryptography Specifications Version 2.1", RFC 3447,
   February 2003.

   [SHA] FIPS PUB 180-2: Specifications for the Secure Hash Standard,
   August 2002.
   http://csrc.nist.gov/publications/fips/fips180-2/fips180-2.pdf.



   Weis                 Expires December, 2005                [Page 9]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005


9.2 Informative References

   [AES-GCM] Viega, J., and D. McGrew, "The Use of Galois/Counter Mode
   (GCM) in IPsec ESP", draft-ietf-ipsec-ciph-aes-gcm-00.txt, April 27,
   2004.

   [GDOI] Baugher, M., Weis, B., Hardjono, T., and H. Harney, "The Group
   Domain of Interpretation", RFC 3547, December 2002.

   [HMAC-SHA] Madson, C., and R. Glenn, "The Use of HMAC-SHA-1-96 within
   ESP and AH", RFC 2404, November 1998.

   [IKEV2] C. Kaufman, "Internet Key Exchange (IKEv2) Protocol", draft-
   ietf-ipsec-ikev2-17.txt, September 23, 2004.

   [RSA-TR] B. Kaliski, "TWIRL and RSA Key Size", RSA Laboratories
   Technical Note, http://www.rsasecurity.com/rsalabs/node.asp?id=2004,
   May 6, 2003.

   [TWIRL] Shamir, A., and E. Tromer, "Factoring Large Numbers with the
   TwIRL Device", Draft, February 9, 2003.

Author's Address

   Brian Weis
   Cisco Systems
   170 W. Tasman Drive,
   San Jose, CA 95134-1706, USA
   (408) 526-4796
   bew@cisco.com

Full Copyright Statement

   Copyright (C) The Internet Society (2005).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.







   Weis                 Expires December, 2005               [Page 10]


           The Use of RSA/SHA-1 Signatures with ESP and AH  June, 2005



Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed
   to pertain to the implementation or use of the technology
   described in this document or the extent to which any license
   under such rights might or might not be available; nor does it
   represent that it has made any independent effort to identify any
   such rights.  Information on the procedures with respect to rights
   in RFC documents can be found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use
   of such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository
   at http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention
   any copyrights, patents or patent applications, or other
   proprietary rights that may cover technology that may be required
   to implement this standard.  Please address the information to the
   IETF at ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.
























   Weis                 Expires December, 2005               [Page 11]