Network Working Group                                   J. Schoenwaelder
Internet-Draft                                         Jacobs University
Intended status: Standards Track                        December 8, 2011
Expires: June 10, 2012


            Translation of SMIv2 MIB Modules to YANG Modules
                     draft-ietf-netmod-smi-yang-03

Abstract

   YANG is a data modeling language used to model configuration and
   state data manipulated by the NETCONF protocol, NETCONF remote
   procedure calls, and NETCONF notifications.  The Structure of
   Management Information (SMIv2) defines fundamental data types, an
   object model, and the rules for writing and revising MIB modules for
   use with the SNMP protocol.  This document defines a translation of
   SMIv2 MIB modules into YANG modules, enabling read-only access to
   data objects defined in SMIv2 MIB modules via NETCONF.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on June 10, 2012.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must



Schoenwaelder             Expires June 10, 2012                 [Page 1]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s) controlling
   the copyright in such materials, this document may not be modified
   outside the IETF Standards Process, and derivative works of it may
   not be created outside the IETF Standards Process, except to format
   it for publication as an RFC or to translate it into languages other
   than English.




































Schoenwaelder             Expires June 10, 2012                 [Page 2]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  4
   2.  Mapping of Well Known Types  . . . . . . . . . . . . . . . . .  5
   3.  Translation of SMIv2 Modules and SMIv2 IMPORT Clauses  . . . .  6
     3.1.  Example: IMPORTS of IF-MIB . . . . . . . . . . . . . . . .  7
   4.  Translation of the MODULE-IDENTITY Macro . . . . . . . . . . .  8
     4.1.  MODULE-IDENTITY Translation Rules  . . . . . . . . . . . .  8
     4.2.  Example: MODULE-IDENTITY of IF-MIB . . . . . . . . . . . .  9
   5.  Translation of the TEXTUAL-CONVENTION Macro  . . . . . . . . . 10
     5.1.  TEXTUAL-CONVENTION Translation Rules . . . . . . . . . . . 10
     5.2.  Example: OwnerString and InterfaceIndex of IF-MIB  . . . . 11
     5.3.  Example: IfDirection of the DIFFSERV-MIB . . . . . . . . . 11
   6.  Translation of OBJECT IDENTIFIER Assignments . . . . . . . . . 13
   7.  Translation of the OBJECT-TYPE Macro . . . . . . . . . . . . . 14
     7.1.  Scalar and Columnar Object Translation Rules . . . . . . . 14
     7.2.  Example: ifNumber and ifIndex of the IF-MIB  . . . . . . . 15
     7.3.  Non-Augmenting Conceptual Table Translation Rules  . . . . 16
     7.4.  Example: ifTable of the IF-MIB . . . . . . . . . . . . . . 18
     7.5.  Example: ifRcvAddressTable of the IF-MIB . . . . . . . . . 18
     7.6.  Example: alHostTable of the RMON2-MIB  . . . . . . . . . . 20
     7.7.  Augmenting Conceptual Tables Translation Rules . . . . . . 21
     7.8.  Example: ifXTable of the IF-MIB  . . . . . . . . . . . . . 22
   8.  Translation of the OBJECT-IDENTITY Macro . . . . . . . . . . . 24
     8.1.  OBJECT-IDENTITY Translation Rules  . . . . . . . . . . . . 24
     8.2.  Example: diffServTBParamSimpleTokenBucket of the
           DIFFSERV-MIB . . . . . . . . . . . . . . . . . . . . . . . 24
   9.  Translation of the NOTIFICATION-TYPE Macro . . . . . . . . . . 25
     9.1.  NOTIFICATION-TYPE Translation Rules  . . . . . . . . . . . 25
     9.2.  Example: linkDown NOTIFICATION-TYPE of IF-MIB  . . . . . . 25
   10. YANG Language Extension Definition . . . . . . . . . . . . . . 28
   11. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 32
   12. Security Considerations  . . . . . . . . . . . . . . . . . . . 33
   13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 34
   14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 35
     14.1. Normative References . . . . . . . . . . . . . . . . . . . 35
     14.2. Informative References . . . . . . . . . . . . . . . . . . 35
   Appendix A.  Mapping of Well Known Types (normative) . . . . . . . 37
   Appendix B.  Module Prefix Generation (informative)  . . . . . . . 40
   Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 41











Schoenwaelder             Expires June 10, 2012                 [Page 3]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


1.  Introduction

   This document describes a translation of SMIv2 [RFC2578], [RFC2579],
   [RFC2580] MIB modules into YANG [RFC6020] modules, enabling read-only
   access to data objects defined in SMIv2 MIB modules via NETCONF.  The
   mapping is illustrated by examples showing the translation of parts
   of the IF-MIB [RFC2863], the DIFFSERV-MIB [RFC3289], and the RMON2-
   MIB [RFC4502] SMIv2 module.

   SMIv1 modules may be converted to YANG by first following the rules
   in [RFC3584] to convert the SMIv1 module to SMIv2, then following the
   rules in this document to convert to YANG.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14, [RFC2119].


































Schoenwaelder             Expires June 10, 2012                 [Page 4]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


2.  Mapping of Well Known Types

   The SMIv2 base types and some well known derived textual conventions
   are mapped to YANG types according to Appendix A.  The mapping of the
   OCTET STRING depends on the context.  If an OCTET STRING type has an
   associated DISPLAY-HINT, then the corresponding YANG base type is the
   string type.  Otherwise, the binary type is used.  Similarly, the
   mapping of the INTEGER type depends on its usage as an enumeration or
   a 32-bit integral type.  Implementations are encouraged to provide
   options to handle situations where DISPLAY-HINTs are added during a
   revision of a module and backwards compatibility must be preserved.

   The mappings shown in Appendix A may impact the imports of the
   generated YANG module since some SMIv2 types and textual conventions
   map to YANG types defined in the ietf-yang-types and ietf-inet-types
   YANG modules defined in [RFC6021] and the ietf-yang-smiv2 YANG module
   defined in this document.  Implementations MUST add any additional
   imports required by the type mapping.

































Schoenwaelder             Expires June 10, 2012                 [Page 5]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


3.  Translation of SMIv2 Modules and SMIv2 IMPORT Clauses

   SMIv2 modules are mapped to corresponding YANG modules.  The YANG
   module name MUST be the same as the SMIv2 module name.

   The YANG namespace MUST be constructed out of a constant prefix
   followed by the SMIv2 module name.  Since SMIv2 module names can be
   assumed to be unique (see Section 3 in [RFC2578]), the resulting YANG
   namespace is unique.  The registered prefix is
   urn:ietf:params:xml:ns:yang:smiv2:, see the IANA considerations in
   Section 11.

   The YANG prefix MAY be derived from the SMIv2 module name using the
   module prefix generation algorithm described in Appendix B.  The YANG
   prefix is supposed to be short and it must be unique within the set
   of all prefixes used by a YANG module.  The algorithm described in
   Appendix B generates such prefixes.

   SMIv2 IMPORT clauses are translated to YANG import statements.  One
   major difference between the SMIv2 import mechanism and the YANG
   import mechanism is that SMIv2 IMPORT clauses import specific symbols
   from an SMIv2 module while the YANG import statement imports all
   symbols of the referenced YANG module.

   In order to produce correct and complete YANG import statements, the
   following rules MUST be used:

   o  Process each item in each SMIv2 IMPORT clause as follows:

      1.  If an import statement for this SMIv2 module has already been
          generated, then ignore this item.

      2.  Otherwise, if the SMIv2 module name is SNMPv2-SMI or SNMPv2-
          CONF, then ignore this item.  Note that these two modules can
          be completely ignored since all definitions in these modules
          are translated by translation rules.

      3.  Otherwise, if this item is a textual convention matching one
          of the textual conventions in the SMIv2 types column of
          Appendix A (e.g., MacAddress, PhysAddress, or TimeStamp) then
          ignore this item.

      4.  Otherwise, if the item is used in a SYNTAX clause of an
          OBJECT-TYPE whose MAX-ACCESS is not accessible-for-notify,
          then generate an import statement as described below.

      5.  Otherwise, if the item is used in an OBJECTS clause of a
          NOTIFICATION-TYPE, then generate an import statement as



Schoenwaelder             Expires June 10, 2012                 [Page 6]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


          described below.

      6.  Otherwise, if the item is used in an INDEX or AUGMENTS clause,
          then generate an import statement as described below.

      7.  Otherwise, ignore this item.  Some examples of this case are
          OBJECT IDENTIFIER assignments and objects that are only
          referenced in MODULE-COMPLIANCE, OBJECT-GROUP, or
          NOTIFICATION-GROUP clauses.

   o  Generate any additional import statements as required by the type
      translations according to the type mapping table Appendix A.  This
      requires the translator to consider all the types used in the
      SMIv2 module in order to produce the imports.

   o  Generate an import statement for the YANG module ietf-yang-smiv2
      with the prefix smiv2.

   The generated import statements use the untranslated SMIv2 module
   names or the names of well-known YANG modules as their argument.  The
   import statement must contain a prefix statement.  The prefixes MAY
   be generated by applying the module prefix generation algorithm
   described in Appendix B.

3.1.  Example: IMPORTS of IF-MIB

   The translation of the IF-MIB [RFC2863] leads to the YANG module and
   namespace/prefix statement and the import statements shown below.
   The prefix is the translation of the SMIv2 module name IF-MIB to
   lowercase (consisting of two tokens and thus no further
   abbreviation).

     module IF-MIB {

       namespace "urn:ietf:params:xml:ns:yang:smiv2:IF-MIB";
       prefix "if-mib";

       import IANAifType-MIB      { prefix "ianaiftype-mib"; }
       import SNMPv2-TC           { prefix "snmpv2-tc"; }
       import ietf-yang-types     { prefix "yang"; }
       import ietf-yang-smiv2     { prefix "smiv2"; }
     }









Schoenwaelder             Expires June 10, 2012                 [Page 7]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


4.  Translation of the MODULE-IDENTITY Macro

   The SMIv2 requires an invocation of the MODULE-IDENTITY macro to
   provide contact and revision history for a MIB module.  The clauses
   of the SMIv2 MODULE-IDENTITY macro MUST be translated into YANG
   statements as detailed below.

4.1.  MODULE-IDENTITY Translation Rules

   o  The SMIv2 ORGANIZATION clause is mapped to the YANG organization
      statement.

   o  The SMIv2 CONTACT-INFO clause is mapped to the YANG contact
      statement.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  Each SMIv2 REVISION clause is mapped to a YANG revision statement.
      The revision is identified by the date argument of the SMIv2
      REVISION clause.  DESCRIPTION sub-clauses of REVISION clauses are
      mapped to corresponding description statement nested in revision
      clauses.

   o  The SMIv2 LAST-UPDATED clause is ignored if the associated date
      matches a REVISION clause.  Otherwise, an additional revision
      statement is generated.

   o  A top-level YANG container is generated.  The container's name is
      the SMIv2 module name and the container MUST be config false.  The
      generation of the top-level container MAY be skipped if the SMIv2
      module does not define any objects that go into the top-level
      container (e.g., an SMIv2 module only defining textual
      conventions).

   o  The object identifier value of the invocation of the SMIv2 MODULE-
      IDENTITY is translated into an smiv2:oid statement contained in an
      smiv2:alias statement representing the MODULE-IDENTITY macro
      invocation.  Refer to the YANG extension defined in Section 10.

   While all proper SMIv2 modules must have exactly one MODULE-IDENTITY
   macro invocation, there are a few notable exceptions.  The modules
   defining the SMIv2 language (i.e., the SNMPv2-SMI, SNMPv2-TC, and
   SNMPv2-CONF modules) do not invoke the MODULE-IDENTITY macro.
   Furthermore, SMIv2 modules generated from SMIv1 modules may miss an
   invocation of the MODULE-IDENTITY macro as well.  In such cases, it
   is preferable to not generate organization, contact, description, and
   revision statements.



Schoenwaelder             Expires June 10, 2012                 [Page 8]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


4.2.  Example: MODULE-IDENTITY of IF-MIB

   The translation of the MODULE-IDENTITY of the IF-MIB [RFC2863] leads
   to the following YANG statements:

     organization
      "IETF Interfaces MIB Working Group";

     contact
      "Keith McCloghrie
       Cisco Systems, Inc.
       170 West Tasman Drive
       San Jose, CA  95134-1706
       US

       408-526-5260
       kzm@cisco.com";

     description
      "The MIB module to describe generic objects for network
       interface sub-layers.  This MIB is an updated version of
       MIB-II's ifTable, and incorporates the extensions defined in
       RFC 1229.";

     revision "2000-06-14" {
       description
        "Clarifications agreed upon by the Interfaces MIB WG, and
         published as RFC 2863.";
     }
     revision "1996-02-28" {
       description
        "Revisions made by the Interfaces MIB WG, and published in
         RFC 2233.";
     }
     revision "1993-11-08" {
       description
        "Initial revision, published as part of RFC 1573.";
     }

     container IF-MIB {
       config false;
     }









Schoenwaelder             Expires June 10, 2012                 [Page 9]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


5.  Translation of the TEXTUAL-CONVENTION Macro

   The SMIv2 uses invocations of the TEXTUAL-CONVENTION macro to define
   new types derived from the SMIv2 base types.  Invocations of the
   TEXTUAL-CONVENTION macro MUST be translated into YANG typedef
   statements as detailed below.

5.1.  TEXTUAL-CONVENTION Translation Rules

   The name of the TEXTUAL-CONVENTION macro invocation is used as the
   name of the generated typedef statement.  The clauses of the SMIv2
   TEXTUAL-CONVENTION macro are mapped to YANG statements embedded in
   the typedef statement as follows:

   o  The SMIv2 DISPLAY-HINT clause is used to determine the type
      mapping of types derived form the OCTET STRING type as explained
      in Section 2.  Furthermore, the DISPLAY-HINT value MAY be used to
      generate a regular expression for the YANG pattern statement
      within the type statement.

   o  The SMIv2 DISPLAY-HINT is translated into an smiv2:display-hint
      statement.  Refer to the YANG extension defined in Section 10.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The SMIv2 SYNTAX clause is mapped to the YANG type statement.
      SMIv2 range restrictions are mapped to YANG range statements while
      SMIv2 length restrictions are mapped to YANG length statements.
      SMIv2 INTEGER enumerations are mapped to YANG enum/value
      statements.  SMIv2 BITS are mapped to YANG bit/position
      statements.

   This translation assumes that labels of named numbers and named bits
   do not change when an SMIv2 module is revised.  This is consistent
   with the clarification of the SMIv2 module revision rules in Section
   4.9 of [RFC4181].







Schoenwaelder             Expires June 10, 2012                [Page 10]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


5.2.  Example: OwnerString and InterfaceIndex of IF-MIB

   The translation of the OwnerString and InterfaceIndex textual
   conventions of the IF-MIB [RFC2863] are shown below.

     typedef OwnerString {
       type string {
         length "0..255";
         pattern '\p{IsBasicLatin}{0,255}';
       }
       status deprecated;
       description
        "This data type is used to model an administratively
         assigned name of the owner of a resource.  This information
         is taken from the NVT ASCII character set.  It is suggested
         that this name contain one or more of the following: ASCII
         form of the manager station's transport address, management
         station name (e.g., domain name), network management
         personnel's name, location, or phone number.  In some cases
         the agent itself will be the owner of an entry.  In these
         cases, this string shall be set to a string starting with
         'agent'.";
       smiv2:display-hint "255a";
     }

     typedef InterfaceIndex {
       type int32 {
         range "1..2147483647";
       }
       description
        "A unique value, greater than zero, for each interface or
         interface sub-layer in the managed system.  It is
         recommended that values are assigned contiguously starting
         from 1.  The value for each interface sub-layer must remain
         constant at least from one re-initialization of the entity's
         network management system to the next re-initialization.";
       smiv2:display-hint "d";
     }

5.3.  Example: IfDirection of the DIFFSERV-MIB

   The translation of the IfDirection textual convention of the
   DIFFSERV-MIB [RFC3289] is shown below.








Schoenwaelder             Expires June 10, 2012                [Page 11]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


   typedef IfDirection {
     type enumeration {
       enum inbound  { value 1; }
       enum outbound { value 2; }
     }
     description
      "IfDirection specifies a direction of data travel on an
       interface. 'inbound' traffic is operated on during reception from
       the interface, while 'outbound' traffic is operated on prior to
       transmission on the interface.";
   }








































Schoenwaelder             Expires June 10, 2012                [Page 12]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


6.  Translation of OBJECT IDENTIFIER Assignments

   The SMIv2 uses OBJECT IDENTIFIER assignments to introduce names for
   intermediate nodes in the OBJECT IDENTIFIER tree.  OBJECT IDENTIFIER
   assignments are translated into smiv2:alias statements.  Refer to the
   YANG extension defined in Section 10.













































Schoenwaelder             Expires June 10, 2012                [Page 13]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


7.  Translation of the OBJECT-TYPE Macro

   The SMIv2 uses the OBJECT-TYPE macro to define objects and the
   structure of conceptual tables.  Objects exist either as scalars
   (exactly one instance within an SNMP context) or columnar objects
   within conceptual tables (zero or multiple instances within an SNMP
   context).  A number of auxiliary objects define the index (key) of a
   conceptual table.  Furthermore, conceptual tables can be augmented by
   other conceptual tables.  All these differences must be taken into
   account when translating SMIv2 OBJECT-TYPE macro invocations to YANG.
   Invocations of the OBJECT-TYPE macro MUST be translated into YANG
   statements as detailed below.

7.1.  Scalar and Columnar Object Translation Rules

   SMIv2 OBJECT-TYPE macro invocations defining scalars or columnar
   objects with a MAX-ACCESS of "not-accessible", "read-only",
   "read-write" and "read-create" are translated to YANG leaf
   statements.  Additionally, columnar objects with a MAX-ACCESS of
   accessible-for-notify are translated to YANG leaf statements if that
   columnar object is part of the INDEX clause of the table containing
   that columnar object.  The name of the leaf is the name associated
   with the SMIv2 OBJECT-TYPE macro invocation.  SMIv2 OBJECT-TYPE macro
   invocations with a MAX-ACCESS of "accessible-for-notify" are not
   translated to YANG data tree leafs but instead into YANG notification
   leafs.

   Leaf statements for scalar objects are created in a container
   representing the scalar's parent node in the OID tree.  This
   container is named after the scalar's parent node in the OID tree and
   placed in the top-level container representing the SMIv2 module, see
   Section 4.1.  In the rare case that the scalar's parent node has
   multiple names, the automatic translation MUST fail with an error and
   the name clash needs to be investigated and fixed manually.  In case
   a previous revision of the SMIv2 module did not have an ambiguity,
   then the name used by the previous revision MUST be used.  The leaf
   statements representing columnar objects are created in the list
   representing a conceptual row, see Section 7.3.

   o  The SMIv2 SYNTAX clause is mapped to the YANG type statement.
      SMIv2 range restrictions are mapped to YANG range statements while
      SMIv2 length restrictions are mapped to YANG length statements.
      SMIv2 INTEGER enumerations are mapped to YANG enum/value
      statements.  SMIv2 BITS are mapped to YANG bit/position
      statements.

   o  The SMIv2 UNITS clause is mapped to the YANG units statement.




Schoenwaelder             Expires June 10, 2012                [Page 14]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


   o  The SMIv2 MAX-ACCESS is translated into an smiv2:max-access
      statement.  Refer to the YANG extension defined in Section 10.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The SMIv2 DEFVAL clause is mapped to an smiv2:defval statement.
      Refer to the YANG extension defined in Section 10.

   o  The value of the SMIv2 OBJECT-TYPE macro invocation is translated
      into an smiv2:oid statement.  Refer to the YANG extension defined
      in Section 10.

   This translation assumes that labels of named numbers and named bits
   do not change when an SMIv2 module is revised.  This is consistent
   with the clarification of the SMIv2 module revision rules in Section
   4.9 of [RFC4181].

7.2.  Example: ifNumber and ifIndex of the IF-MIB

   The translations of the ifNumber scalar object and the ifIndex
   columnar object of the IF-MIB [RFC2863] are shown below.  Since
   ifNumber is a scalar object in the interfaces branch of the IF-MIB,
   the YANG leaf ifNumber will be placed in a YANG container called
   interfaces, which is registered in the top-level container IF-MIB.



















Schoenwaelder             Expires June 10, 2012                [Page 15]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


     leaf ifNumber {
       type int32;
       description
        "The number of network interfaces (regardless of their
         current state) present on this system.";
       smiv2:max-access "read-only";
       smiv2:oid "1.3.6.1.2.1.2.1";
     }

     leaf ifIndex {
       type if-mib:InterfaceIndex;
       description
        "A unique value, greater than zero, for each interface.  It
         is recommended that values are assigned contiguously
         starting from 1.  The value for each interface sub-layer
         must remain constant at least from one re-initialization of
         the entity's network management system to the next re-
         initialization.";
       smiv2:max-access "read-only";
       smiv2:oid "1.3.6.1.2.1.2.2.1.1";
     }

7.3.  Non-Augmenting Conceptual Table Translation Rules

   An OBJECT-TYPE macro invocation defining a non-augmenting conceptual
   table is translated to a YANG container statement using the name of
   the OBJECT-TYPE macro invocation.  This container is created in the
   top-level container representing the SMIv2 module.  The clauses of
   the macro are translated as follows:

   o  The SMIv2 SYNTAX clause is ignored

   o  The SMIv2 UNITS clause is ignored.

   o  The SMIv2 MAX-ACCESS clause is ignored.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The value of the SMIv2 OBJECT-TYPE macro invocation is translated
      into an smiv2:oid statement.  Refer to the YANG extension defined



Schoenwaelder             Expires June 10, 2012                [Page 16]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


      in Section 10.

   An OBJECT-TYPE macro invocation defining a conceptual row is
   translated to a YANG list statement.  It is contained in the YANG
   container representing the conceptual table.  The generated list uses
   the name of the row OBJECT-TYPE macro invocation.  The clauses of the
   OBJECT-TYPE macro are translated as follows:

   o  The SMIv2 SYNTAX clause is ignored.

   o  The SMIv2 UNITS clause is ignored.

   o  The SMIv2 MAX-ACCESS clause is ignored.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The SMIv2 INDEX clause is mapped to the YANG key clause listing
      the columnar objects forming the key of the YANG list.  If the
      same object appears more than once in the INDEX clause, append
      '_<n>' to the duplicate object name(s) where '<n>' counts the
      occurances of the object in the INDEX clause, starting from 2.
      Additional leaf statements must be created to define the leafs
      introduced.

   o  If the SMIv2 INDEX clause contains the IMPLIED keyword, then an
      smiv2:implied statement is generated to record the name of the
      object preceded by the IMPLIED keyword.  Refer to the YANG
      extension defined in Section 10.

   o  The value of the SMIv2 OBJECT-TYPE macro invocation is translated
      into an smiv2:oid statement.  Refer to the YANG extension defined
      in Section 10.

   Within the list statement, YANG leaf statements are created for
   columnar objects as described in Section 7.1.  For objects listed in
   the SMIv2 INDEX clause that are not part of the conceptual table
   itself, YANG leaf statements of type leafref pointing to the
   referenced definition are created.





Schoenwaelder             Expires June 10, 2012                [Page 17]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


7.4.  Example: ifTable of the IF-MIB

   The translation of the definition of the ifTable of the IF-MIB
   [RFC2863] is shown below.

     container ifTable {
       description
        "A list of interface entries.  The number of entries is
         given by the value of ifNumber.";
       smiv2:oid "1.3.6.1.2.1.2.2";

       list ifEntry {
         key "ifIndex";
         description
          "An entry containing management information applicable to a
           particular interface.";
         smiv2:oid "1.3.6.1.2.1.2.2.1";

         leaf ifIndex {
           type if-mib:InterfaceIndex;
           description
            "A unique value, greater than zero, for each interface.  It
             is recommended that values are assigned contiguously
             starting from 1.  The value for each interface sub-layer
             must remain constant at least from one re-initialization of
             the entity's network management system to the next re-
             initialization.";
           smiv2:max-access "read-only";
           smiv2:oid "1.3.6.1.2.1.2.2.1.1";
         }

         // ...
       }
     }

7.5.  Example: ifRcvAddressTable of the IF-MIB

   The translation of the definition of the ifRcvAddressTable of the IF-
   MIB [RFC2863] is shown below.












Schoenwaelder             Expires June 10, 2012                [Page 18]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


     container ifRcvAddressTable {
       description
        "This table contains an entry for each address (broadcast,
         multicast, or uni-cast) for which the system will receive
         packets/frames on a particular interface, except as follows:

         - for an interface operating in promiscuous mode, entries
         are only required for those addresses for which the system
         would receive frames were it not operating in promiscuous
         mode.

         - for 802.5 functional addresses, only one entry is
         required, for the address which has the functional address
         bit ANDed with the bit mask of all functional addresses for
         which the interface will accept frames.

         A system is normally able to use any unicast address which
         corresponds to an entry in this table as a source address.";
       smiv2:oid "1.3.6.1.2.1.31.1.4";

       list ifRcvAddressEntry {
         key "ifIndex ifRcvAddressAddress";
         description
          "A list of objects identifying an address for which the
           system will accept packets/frames on the particular
           interface identified by the index value ifIndex.";
         smiv2:oid "1.3.6.1.2.1.31.1.4.1";

         leaf ifIndex {
           type leafref {
             path "/if-mib:IF-MIB/if-mib:ifTable" +
                  "/if-mib:ifEntry/if-mib:ifIndex";
           }
         }

         leaf ifRcvAddressAddress {
           type yang:phys-address;
           description
            "An address for which the system will accept packets/frames
             on this entry's interface.";
           smiv2:max-access "not-accessible";
           smiv2:oid "1.3.6.1.2.1.31.1.4.1.1";
         }

         // ...
       }
     }




Schoenwaelder             Expires June 10, 2012                [Page 19]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


7.6.  Example: alHostTable of the RMON2-MIB

   The translation of the definition of the alHostTable of the RMON2-MIB
   [RFC4502] is shown below.

   container alHostTable {
     description
      "A collection of statistics for a particular protocol from a
       particular network address that has been discovered on an
       interface of this device.

       The probe will populate this table for all protocols in the
       protocol directory table whose value of
       protocolDirHostConfig is equal to supportedOn(3), and
       will delete any entries whose protocolDirEntry is deleted or
       has a protocolDirHostConfig value of supportedOff(2).

       The probe will add to this table all addresses
       seen as the source or destination address in all packets with
       no MAC errors and will increment octet and packet counts in
       the table for all packets with no MAC errors.  Further,
       entries will only be added to this table if their address
       exists in the nlHostTable and will be deleted from this table
       if their address is deleted from the nlHostTable.";
     smiv2:oid "1.3.6.1.2.1.16.16.1";

     list alHostEntry {
       key "hlHostControlIndex alHostTimeMark protocolDirLocalIndex "
         + "nlHostAddress protocolDirLocalIndex_2";
       description
        "A conceptual row in the alHostTable.

         The hlHostControlIndex value in the index identifies the
         hlHostControlEntry on whose behalf this entry was created.
         The first protocolDirLocalIndex value in the index identifies
         the network-layer protocol of the address.
         The nlHostAddress value in the index identifies the network-
         layer address of this entry.
         The second protocolDirLocalIndex value in the index identifies
         the protocol that is counted by this entry.

         An example of the indexing in this entry is
         alHostOutPkts.1.783495.18.4.128.2.6.6.34.

         Note that some combinations of index values may result in an
         index that exceeds 128 sub-identifiers in length, which exceeds
         the maximum for the SNMP protocol.  Implementations should take
         care to avoid such combinations.";



Schoenwaelder             Expires June 10, 2012                [Page 20]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


       smiv2:oid "1.3.6.1.2.1.16.16.1.1";

       // ...

       leaf protocolDirLocalIndex {
         type leafref {
           path "/rmon2-mib:RMON2-MIB/"
              + "rmon2-mib:protocolDirTable/"
              + "rmon2-mib:protocolDirEntryf/"
              + "rmon2-mib:protocolDirLocalIndex";
         }
       }

       // ...

       leaf protocolDirLocalIndex_2 {
         type leafref {
           path "/rmon2-mib:RMON2-MIB/"
              + "rmon2-mib:protocolDirTable/"
              + "rmon2-mib:protocolDirEntry/"
              + "rmon2-mib:protocolDirLocalIndex";
         }
       }

       // ...
     }
   }

7.7.  Augmenting Conceptual Tables Translation Rules

   An OBJECT-TYPE macro invocation defining an augmenting conceptual
   table is translated to a YANG smiv2:alias statement.  Refer to the
   YANG extension defined in Section 10.  The clauses of the macro are
   translated as follows:

   o  The SMIv2 SYNTAX clause is ignored.

   o  The SMIv2 UNITS clause is ignored.

   o  The SMIv2 MAX-ACCESS clause is ignored.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.




Schoenwaelder             Expires June 10, 2012                [Page 21]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The value of the SMIv2 OBJECT-TYPE macro invocation is translated
      into an smiv2:oid statement.  Refer to the YANG extension defined
      in Section 10.

   An OBJECT-TYPE macro invocation defining a conceptual row
   augmentation is translated to a YANG smiv2:alias statement and a YANG
   augment statement using the path to the augmented table as its
   argument.  The clauses of the OBJECT-TYPE macro are translated as
   follows:

   o  The SMIv2 SYNTAX clause is ignored.

   o  The SMIv2 UNITS clause is ignored.

   o  The SMIv2 MAX-ACCESS clause is ignored.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The value of the SMIv2 OBJECT-TYPE macro invocation is translated
      into an smiv2:oid statement.  Refer to the YANG extension defined
      in Section 10.

   Within the augment statement, YANG leaf statements are created as
   described in Section 7.1.

7.8.  Example: ifXTable of the IF-MIB

   The translation of the definition of the ifXTable of the IF-MIB
   [RFC2863] is shown below.











Schoenwaelder             Expires June 10, 2012                [Page 22]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


     smiv2:alias "ifXTable" {
       description
        "A list of interface entries.  The number of entries is
         given by the value of ifNumber.  This table contains
         additional objects for the interface table.";
       smiv2:oid "1.3.6.1.2.1.31.1.1";
     }

     smiv2:alias "ifXEntry" {
       description
        "An entry containing additional management information
         applicable to a particular interface.";
       smiv2:oid "1.3.6.1.2.1.31.1.1.1";
     }

     augment "/if-mib:IF-MIB/if-mib:ifTable/if-mib:ifEntry" {
       description
        "An entry containing additional management information
         applicable to a particular interface.";
       smiv2:oid "1.3.6.1.2.1.31.1.1.1";

       leaf ifName {
         type snmpv2-tc:DisplayString;
         description
          "The textual name of the interface.  The value of this
           object should be the name of the interface as assigned by
           the local device and should be suitable for use in commands
           entered at the device's `console'.  This might be a text
           name, such as `le0' or a simple port number, such as `1',
           depending on the interface naming syntax of the device.  If
           several entries in the ifTable together represent a single
           interface as named by the device, then each will have the
           same value of ifName.  Note that for an agent which responds
           to SNMP queries concerning an interface on some other
           (proxied) device, then the value of ifName for such an
           interface is the proxied device's local name for it.

           If there is no local name, or this object is otherwise not
           applicable, then this object contains a zero-length string.";
         smiv2:max-access "read-only";
         smiv2:oid "1.3.6.1.2.1.31.1.1.1.1";
       }

       // ...
     }






Schoenwaelder             Expires June 10, 2012                [Page 23]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


8.  Translation of the OBJECT-IDENTITY Macro

   The SMIv2 uses invocations of the OBJECT-IDENTITY macro to define
   information about an OBJECT IDENTIFIER assignment.  Invocations of
   the OBJECT-IDENTITY macro MUST be translated into YANG identity
   statements as detailed below.

8.1.  OBJECT-IDENTITY Translation Rules

   The name of the OBJECT-IDENTITY macro invocation is used as the name
   of the generated identity statement.  The generated identity
   statement uses the smiv2:object-identity defined in Section 10 as its
   base.  The clauses of the SMIv2 OBJECT-IDENTITY macro are mapped to
   YANG statements as follows:

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The value of the SMIv2 OBJECT-IDENTITY macro invocation is
      translated into an smiv2:oid statement.  Refer to the YANG
      extension defined in Section 10.

8.2.  Example: diffServTBParamSimpleTokenBucket of the DIFFSERV-MIB

   The translation of the diffServTBParamSimpleTokenBucket of the
   DIFFSERV-MIB [RFC3289] is shown below.

     identity diffServTBParamSimpleTokenBucket {
       base "smiv2:object-identity";
       description
        "Two Parameter Token Bucket Meter as described in the Informal
         Differentiated Services Model section 5.2.3.";
       smiv2:oid "1.3.6.1.2.1.97.3.1.1";
     }










Schoenwaelder             Expires June 10, 2012                [Page 24]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


9.  Translation of the NOTIFICATION-TYPE Macro

   The SMIv2 provides the NOTIFICATION-TYPE macro to define event
   notifications.  YANG provides the notification statement for the same
   purpose.  Invocations of the NOTIFICATION-TYPE macro MUST be
   translated into YANG notification statements as detailed below.

9.1.  NOTIFICATION-TYPE Translation Rules

   The name of the NOTIFICATION-TYPE macro invocation is used as the
   name of the generated notification statement.  The clauses of the
   NOTIFICATION-TYPE macro are mapped to YANG statements embedded in the
   notification statement as follows.

   o  The SMIv2 OBJECTS clause is mapped to a sequence of YANG
      containers.  For each object listed in the OBJECTS clause value, a
      YANG container statement is generated.  The name of this container
      is the string "object-<n>", where <n> is the position of the
      object in the value of the OBJECTS clause (first element has
      position 1).  If the current object belongs to a conceptual table,
      then a sequence of leaf statements is generated for each INDEX
      object of the conceptual table.  These leafs are named after the
      INDEX objects and of type leafref.  Finally, a leaf statement is
      generated named after the current object.  If the current object
      has a MAX-ACCESS of "read-only", "read-write" or "read-create",
      then the generated leaf is of type leafref.  Otherwise, if the
      current object has a MAX-ACCESS of "accessible-for-notify", then a
      leaf is generated, following the itemized steps in Section 7.1.

   o  The SMIv2 STATUS clause is mapped to the YANG status statement.
      The generation of the YANG status statement is skipped if the
      value of the STATUS clause is current.

   o  The SMIv2 DESCRIPTION clause is mapped to the YANG description
      statement.

   o  The SMIv2 REFERENCE clause is mapped to the YANG reference
      statement.

   o  The value of the SMIv2 NOTIFICATION-TYPE macro invocation is
      translated into an smiv2:oid statement.  Refer to the YANG
      extension defined in Section 10.

9.2.  Example: linkDown NOTIFICATION-TYPE of IF-MIB

   The translation of the linkDown notification of the IF-MIB [RFC2863]
   is shown below.




Schoenwaelder             Expires June 10, 2012                [Page 25]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


     notification linkDown {
       description
        "A linkDown trap signifies that the SNMP entity, acting in
         an agent role, has detected that the ifOperStatus object for
         one of its communication links is about to enter the down
         state from some other state (but not from the notPresent
         state).  This other state is indicated by the included value
         of ifOperStatus.";
       smiv2:oid "1.3.6.1.6.3.1.1.5.3";

       container object-1 {
         leaf ifIndex {
           type leafref {
             path "/if-mib:IF-MIB/if-mib:ifTable" +
                  "/if-mib:ifEntry/if-mib:ifIndex";
           }
         }
       }

       container object-2 {
         leaf ifIndex {
           type leafref {
             path "/if-mib:IF-MIB/if-mib:ifTable" +
                  "/if-mib:ifEntry/if-mib:ifIndex";
           }
         }
         leaf ifAdminStatus {
           type leafref {
             path "/if-mib:IF-MIB/if-mib:ifTable" +
                  "/if-mib:ifEntry/if-mib:ifAdminStatus";
           }
         }
       }

       container object-3 {
         leaf ifIndex {
           type leafref {
             path "/if-mib:IF-MIB/if-mib:ifTable" +
                  "/if-mib:ifEntry/if-mib:ifIndex";
           }
         }
         leaf ifOperStatus {
           type leafref {
             path "/if-mib:IF-MIB/if-mib:ifTable" +
                  "/if-mib:ifEntry/if-mib:ifOperStatus";
           }
         }
       }



Schoenwaelder             Expires June 10, 2012                [Page 26]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


     }


















































Schoenwaelder             Expires June 10, 2012                [Page 27]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


10.  YANG Language Extension Definition

   This section defines some YANG extension statements that can be used
   to capture some information present in SMIv2 modules that is not
   translated into core YANG statements.  The YANG module references
   [RFC2578] and [RFC2579].

   <CODE BEGINS> file "ietf-yang-smiv2@2011-11-25.yang"

module ietf-yang-smiv2 {

  namespace "urn:ietf:params:xml:ns:yang:ietf-yang-smiv2";
  prefix "smiv2";

  organization
   "IETF NETMOD (NETCONF Data Modeling Language) Working Group";

  contact
   "WG Web:   <http://tools.ietf.org/wg/netmod/>
    WG List:  <mailto:netmod@ietf.org>

    WG Chair: David Kessens
              <mailto:david.kessens@nsn.com>

    WG Chair: Juergen Schoenwaelder
              <mailto:j.schoenwaelder@jacobs-university.de>

    Editor:   Juergen Schoenwaelder
              <mailto:j.schoenwaelder@jacobs-university.de>";

  description
   "This module defines YANG extensions that are used to translate
    SMIv2 concepts into YANG.

    Copyright (c) 2011 IETF Trust and the persons identified as
    authors of the code.  All rights reserved.

    Redistribution and use in source and binary forms, with or
    without modification, is permitted pursuant to, and subject
    to the license terms contained in, the Simplified BSD License
    set forth in Section 4.c of the IETF Trust's Legal Provisions
    Relating to IETF Documents
    (http://trustee.ietf.org/license-info).

    This version of this YANG module is part of RFC XXXX; see
    the RFC itself for full legal notices.";
    // RFC Ed.: replace XXXX with actual RFC number and remove this note




Schoenwaelder             Expires June 10, 2012                [Page 28]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


  // RFC Ed.: please update the date to the date of publication
  revision 2011-11-25 {
    description
     "Initial revision.";
    reference
     "RFC XXXX: Translation of SMIv2 MIB Modules to YANG Modules";
    // RFC Ed.: replace XXXX with actual RFC number and remove this note
  }

  identity object-identity {
    description
     "Base identity for all SMIv2 OBJECT-IDENTITYs.";
  }

  typedef opaque {
    type binary;
    description
     "The Opaque type supports the capability to pass arbitrary ASN.1
      syntax.  A value is encoded using the ASN.1 Basic Encoding Rules
      into a string of octets.  This, in turn, is encoded as an OCTET
      STRING, in effect 'double-wrapping' the original ASN.1 value.

      In the value set and its semantics, this type is equivalent to
      the Opaque type of the SMIv2. This type exists in the SMIv2
      solely for backward-compatibility reasons and this is also
      true for this YANG data type.";
    reference
     "RFC 2578: Structure of Management Information Version 2 (SMIv2)";
  }

  extension display-hint {
    argument "format";
    description
     "The display-hint statement takes as an argument the DISPLAY-HINT
      assigned to an SMIv2 textual convention.";
    reference
     "RFC2579: Textual Conventions for SMIv2";
  }

  extension max-access {
    argument "access";
    description
     "The max-access statement takes as an argument the MAX-ACCESS
      assigned to an SMIv2 object definition";
    reference
     "RFC2578: Structure of Management Information Version 2 (SMIv2)";
  }




Schoenwaelder             Expires June 10, 2012                [Page 29]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


  extension defval {
    argument "value";
    description
     "The defval statement takes as an argument a default value
      defined by an SMIv2 DEFVAL clause. Note that the value is in
      the SMIv2 value space defined by the SMIv2 syntax of the
      corresponding object and not in the YANG value space
      defined by the corresponding YANG data type.";
    reference
     "RFC2578: Structure of Management Information Version 2 (SMIv2)";
  }

  extension implied {
    argument "index";
    description
     "If an SMIv2 INDEX object is preceded by the IMPLIED keyword, then
      the implied statement is present in the yang module and takes as
      an argument the name of the IMPLIED index object.";
    reference
     "RFC2578: Structure of Management Information Version 2 (SMIv2)";
   }

  extension alias {
    argument "descriptor";
    description
     "The alias statement introduces an SMIv2 descriptor. The body of
      the alias statement is expected to contain an oid statement that
      provides the numeric OID associated with the descriptor.";
    reference
     "RFC2578: Structure of Management Information Version 2 (SMIv2)";
  }

  extension oid {
    argument "value";
    description
     "The oid statement takes as an argument the object identifier
      assigned to an SMIv2 definition. The object identifier value
      is written in decimal dotted notation.";
    reference
     "RFC2578: Structure of Management Information Version 2 (SMIv2)";
  }

  extension subid {
    argument "value";
    description
     "The subid statement takes as an argument the last sub-identifier
      of the object identifier assigned to an SMIv2 definition.  The
      sub-identifier value is a single positive decimal natural number.



Schoenwaelder             Expires June 10, 2012                [Page 30]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


      The subid statement may not be used as a substatement to any
      top-level node in a YANG document.  The subid substatement may
      be used only as a substatement to a node having a parent node
      defined with either a smiv2:oid or smiv2:subid substatement.";
    reference
     "RFC2578: Structure of Management Information Version 2 (SMIv2)";
  }

}

   <CODE ENDS>








































Schoenwaelder             Expires June 10, 2012                [Page 31]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


11.  IANA Considerations

   This document registers two URIs in the IETF XML registry [RFC3688].
   Following the format in RFC 3688, the following registrations have
   been made.

     URI: urn:ietf:params:xml:ns:yang:ietf-yang-smiv2

     Registrant Contact: The NETMOD WG of the IETF.

     XML: N/A, the requested URI is an XML namespace.


     URI: urn:ietf:params:xml:ns:yang:smiv2

     Registrant Contact: The NETMOD WG of the IETF.

     XML: N/A, the requested URI is an XML namespace.

   This document registers a YANG module in the YANG Module Names
   registry [RFC6020].

     name:         ietf-yang-smiv2
     namespace:    urn:ietf:params:xml:ns:yang:ietf-yang-smiv2
     prefix:       smiv2
     reference:    RFC XXXX

























Schoenwaelder             Expires June 10, 2012                [Page 32]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


12.  Security Considerations

   This document defines a translation of SMIv2 MIB modules into YANG
   modules, enabling read-only access to data objects defined in SMIv2
   MIB modules via NETCONF.  The translation itself has no security
   impact on the Internet.

   Users of translated SMIv2 models that have been published as RFCs
   should consult the security considerations of the respective RFCs.
   In addition, the security considerations for the NETCONF protocol
   [RFC6241] should be consulted to understand how NETCONF protects
   potentially sensitive information.







































Schoenwaelder             Expires June 10, 2012                [Page 33]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


13.  Acknowledgements

   The editor wishes to thank the following individuals for providing
   helpful comments on various versions of this document: Andy Bierman,
   Martin Bjorklund, David Reid, and David Spakes.














































Schoenwaelder             Expires June 10, 2012                [Page 34]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


14.  References

14.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Structure of Management Information
              Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

   [RFC2579]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Textual Conventions for SMIv2",
              STD 58, RFC 2579, April 1999.

   [RFC2580]  McCloghrie, K., Perkins, D., and J. Schoenwaelder,
              "Conformance Statements for SMIv2", STD 58, RFC 2580,
              April 1999.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              October 2010.

   [RFC6021]  Schoenwaelder, J., "Common YANG Data Types", RFC 6021,
              October 2010.

14.2.  Informative References

   [RFC2863]  McCloghrie, K. and F. Kastenholz, "The Interfaces Group
              MIB", RFC 2863, June 2000.

   [RFC3289]  Baker, F., Chan, K., and A. Smith, "Management Information
              Base for the Differentiated Services Architecture",
              RFC 3289, May 2002.

   [RFC3584]  Frye, R., Levi, D., Routhier, S., and B. Wijnen,
              "Coexistence between Version 1, Version 2, and Version 3
              of the Internet-standard Network Management Framework",
              RFC 3584, August 2003.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              January 2004.

   [RFC4181]  Heard, C., "Guidelines for Authors and Reviewers of MIB
              Documents", BCP 111, RFC 4181, September 2005.

   [RFC4502]  Waldbusser, S., "Remote Network Monitoring Management
              Information  Base Version 2", RFC 4502, May 2006.



Schoenwaelder             Expires June 10, 2012                [Page 35]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, June 2011.
















































Schoenwaelder             Expires June 10, 2012                [Page 36]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


Appendix A.  Mapping of Well Known Types (normative)

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   INTEGER        (used as an enumeration)
    YANG Type:    enumeration

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   INTEGER        (used as a numeric type)
    YANG Type:    int32

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   Integer32
    YANG Type:    int32

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   OCTET STRING   (used as a binary string)
    YANG Type:    binary

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   OCTET STRING   (used to hold UTF8/ASCII characters)
    YANG Type:    string

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   OBJECT IDENTIFIER
    YANG Module:  ietf-yang-types
    YANG Type:    object-identifier-128

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   BITS
    YANG Type:    bits

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   IpAddress
    YANG Module:  ietf-inet-types
    YANG Type:    ipv4-address

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   Counter32
    YANG Module:  ietf-yang-types
    YANG Type:    counter32

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   Gauge32
    YANG Module:  ietf-yang-types
    YANG Type:    gauge32

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   TimeTicks



Schoenwaelder             Expires June 10, 2012                [Page 37]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


    YANG Module:  ietf-yang-types
    YANG Type:    timeticks

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   Counter64
    YANG Module:  ietf-yang-types
    YANG Type:    counter64

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   Unsigned32
    YANG Type:    uint32

    SMIv2 Module: SNMPv2-SMI
    SMIv2 Type:   Opaque
    YANG Module:  ietf-yang-smiv2
    YANG Type:    opaque

    SMIv2 Module: SNMPv2-TC
    SMIv2 Type:   PhysAddress
    YANG Module:  ietf-yang-types
    YANG Type:    phys-address

    SMIv2 Module: SNMPv2-TC
    SMIv2 Type:   MacAddress
    YANG Module:  ietf-yang-types
    YANG Type:    mac-address

    SMIv2 Module: SNMPv2-TC
    SMIv2 Type:   TruthValue
    YANG Type:    boolean

    SMIv2 Module: SNMPv2-TC
    SMIv2 Type:   TimeStamp
    YANG Module:  ietf-yang-types
    YANG Type:    timestamp

    SMIv2 Module: RMON2-MIB
    SMIv2 Type:   ZeroBasedCounter32
    YANG Module:  ietf-yang-types
    YANG Type:    zero-based-counter32

    SMIv2 Module: HCNUM-TC
    SMIv2 Type:   ZeroBasedCounter64
    YANG Module:  ietf-yang-types
    YANG Type:    zero-based-counter64

    SMIv2 Module: HCNUM-TC
    SMIv2 Type:   CounterBasedGauge64



Schoenwaelder             Expires June 10, 2012                [Page 38]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


    YANG Module:  ietf-yang-types
    YANG Type:    gauge64

    SMIv2 Module: INET-ADDRESS-MIB
    SMIv2 Type:   InetAutonomousSystemNumber
    YANG Module:  ietf-inet-types
    YANG Type:    as-number

    SMIv2 Module: INET-ADDRESS-MIB
    SMIv2 Type:   InetVersion
    YANG Module:  ietf-inet-types
    YANG Type:    ip-version

    SMIv2 Module: INET-ADDRESS-MIB
    SMIv2 Type:   InetPortNumber
    YANG Module:  ietf-inet-types
    YANG Type:    port-number

    SMIv2 Module: DIFFSERV-DSCP-TC
    SMIv2 Type:   Dscp
    YANG Module:  ietf-inet-types
    YANG Type:    dscp

    SMIv2 Module: IPV6-FLOW-LABEL-MIB
    SMIv2 Type:   IPv6FlowLabel
    YANG Module:  ietf-inet-types
    YANG Type:    ipv6-flow-label

    SMIv2 Module: URI-TC-MIB
    SMIv2 Type:   Uri
    YANG Module:  ietf-inet-types
    YANG Type:    uri



















Schoenwaelder             Expires June 10, 2012                [Page 39]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


Appendix B.  Module Prefix Generation (informative)

   This section describes an algorithm to generate module prefixes, to
   be used in the import statements.  The input of the prefix generation
   algorithm is a set of prefixes (usually derived from imported module
   names) and a specific module name to be converted into a prefix.  The
   algorithm described below produces a prefix for the given module name
   that is unique within the set of prefixes.

                       +-----------------+--------+
                       | YANG Module     | Prefix |
                       +-----------------+--------+
                       | ietf-yang-types | yang   |
                       | ietf-inet-types | inet   |
                       | ietf-yang-smiv2 | smiv2  |
                       +-----------------+--------+

           Table 1: Special prefixes for well known YANG modules

   o  First, some predefined translations mapping well known YANG
      modules to short prefixes are tried (see Table 1).  If a fixed
      translation rule exists and leads to a conflict free prefix, then
      the fixed translation is used.

   o  Otherwise, prefixes are generated by tokenizing a YANG module
      name, using hyphens as token separators.  The tokens derived from
      the module name are converted to lowercase characters.  The prefix
      then becomes the shortest sequence of tokens concatenated using
      hyphens as separators, which includes at least two tokens and
      which is unique among all prefixes used in the YANG module.

   In the worst case, the prefix derived from an SMIv2 module name
   becomes the SMIv2 module name translated to lower-case.  But on
   average, much shorter prefixes are generated.

















Schoenwaelder             Expires June 10, 2012                [Page 40]


Internet-Draft        Translation of SMIv2 to YANG         December 2011


Author's Address

   Juergen Schoenwaelder
   Jacobs University

   Email: j.schoenwaelder@jacobs-university.de













































Schoenwaelder             Expires June 10, 2012                [Page 41]