Network Working Group J. Schoenwaelder, Ed.
Internet-Draft Jacobs University
Intended status: Standards Track September 4, 2008
Expires: March 8, 2009
Common YANG Data Types
draft-ietf-netmod-yang-types-00
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on March 8, 2009.
Copyright Notice
Copyright (C) The IETF Trust (2008).
Schoenwaelder Expires March 8, 2009 [Page 1]
Internet-Draft YANG-TYPES September 2008
Abstract
This document introduces a collection of common data types to be used
with the YANG data modeling language.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Core YANG Derived Types . . . . . . . . . . . . . . . . . . . 4
3. Internet Specific Derived Types . . . . . . . . . . . . . . . 12
4. IEEE Specific Derived Types . . . . . . . . . . . . . . . . . 20
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 23
6. Security Considerations . . . . . . . . . . . . . . . . . . . 24
7. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 25
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.1. Normative References . . . . . . . . . . . . . . . . . . . 26
8.2. Informative References . . . . . . . . . . . . . . . . . . 26
Appendix A. XSD Translations . . . . . . . . . . . . . . . . . . 29
A.1. XSD of Core YANG Derived Types . . . . . . . . . . . . . . 29
A.2. XSD of Internet Specific Derived Types . . . . . . . . . . 36
A.3. XSD of IEEE Specific Derived Types . . . . . . . . . . . . 44
Appendix B. RelaxNG Translations . . . . . . . . . . . . . . . . 47
B.1. RelaxNG of Core YANG Derived Types . . . . . . . . . . . . 47
B.2. RelaxNG of Internet Specific Derived Types . . . . . . . . 53
B.3. RelaxNG of IEEE Specific Derived Types . . . . . . . . . . 58
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 61
Intellectual Property and Copyright Statements . . . . . . . . . . 62
Schoenwaelder Expires March 8, 2009 [Page 2]
Internet-Draft YANG-TYPES September 2008
1. Introduction
YANG [YANG] is a data modeling language used to model configuration
and state data manipulated by the NETCONF [RFC4741] protocol. The
YANG language supports a small set of built-in data types and
provides mechanisms to derive other types from the built-in types.
This document introduces a collection of common data types derived
from the built-in YANG data types. The definitions are organized in
several YANG modules. The "yang-types" module contains generally
useful data types. The "inet-types" module contains definitions that
are relevant for the Internet protocol suite while the "ieee-types"
module contains definitions that are relevant for IEEE 802 protocols.
Their derived types are generally designed to be applicable for
modeling all areas of management information.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14, [RFC2119].
Schoenwaelder Expires March 8, 2009 [Page 3]
Internet-Draft YANG-TYPES September 2008
2. Core YANG Derived Types
module yang-types {
namespace "urn:ietf:params:xml:ns:yang:yang-types";
prefix "yang";
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/netmod/>
WG List: <mailto:netmod@ietf.org>
WG Chair: David Partain
<mailto:david.partain@ericsson.com>
WG Chair: David Harrington
<mailto:ietfdbh@comcast.net>
Editor: Juergen Schoenwaelder
<mailto:j.schoenwaelder@jacobs-university.de>";
description
"This module contains a collection of generally useful derived
YANG data types.
Copyright (C) The IETF Trust (2008). This version of this
YANG module is part of RFC XXXX; see the RFC itself for full
legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove this note
revision 2008-08-26 {
description
"Initial revision, published as RFC XXXX.";
}
// RFC Ed.: replace XXXX with actual RFC number and remove this note
/*** collection of counter and gauge types ***/
typedef counter32 {
type uint32;
description
"The counter32 type represents a non-negative integer
which monotonically increases until it reaches a
maximum value of 2^32-1 (4294967295 decimal), when it
wraps around and starts increasing again from zero.
Schoenwaelder Expires March 8, 2009 [Page 4]
Internet-Draft YANG-TYPES September 2008
Counters have no defined `initial' value, and thus, a
single value of a counter has (in general) no information
content. Discontinuities in the monotonically increasing
value normally occur at re-initialization of the
management system, and at other times as specified in the
description of an object instance using this type. If
such other times can occur, for example, the creation of
an object instance of type counter32 at times other than
re-initialization, then a corresponding object should be
defined, with an appropriate type, to indicate the last
discontinuity.
The counter32 type should not be used for configuration
objects. A default statement should not be used for
attributes with a type value of counter32.
This type is in the value set and its semantics equivalent
to the Counter32 type of the SMIv2.";
reference
"RFC 2578: Structure of Management Information Version 2 (SMIv2)";
}
typedef zero-based-counter32 {
type yang:counter32;
default "0";
description
"The zero-based-counter32 type represents a counter32
which has the defined `initial' value zero.
Objects of this type will be set to zero(0) on creation
and will thereafter count appropriate events, wrapping
back to zero(0) when the value 2^32 is reached.
Provided that an application discovers the new object within
the minimum time to wrap it can use the initial value as a
delta since it last polled the table of which this object is
part. It is important for a management station to be aware
of this minimum time and the actual time between polls, and
to discard data if the actual time is too long or there is
no defined minimum time.
This type is in the value set and its semantics equivalent
to the ZeroBasedCounter32 textual convention of the SMIv2.";
reference
"RFC 2021: Remote Network Monitoring Management Information
Base Version 2 using SMIv2";
}
Schoenwaelder Expires March 8, 2009 [Page 5]
Internet-Draft YANG-TYPES September 2008
typedef counter64 {
type uint64;
description
"The counter64 type represents a non-negative integer
which monotonically increases until it reaches a
maximum value of 2^64-1 (18446744073709551615), when
it wraps around and starts increasing again from zero.
Counters have no defined `initial' value, and thus, a
single value of a counter has (in general) no information
content. Discontinuities in the monotonically increasing
value normally occur at re-initialization of the
management system, and at other times as specified in the
description of an object instance using this type. If
such other times can occur, for example, the creation of
an object instance of type counter64 at times other than
re-initialization, then a corresponding object should be
defined, with an appropriate type, to indicate the last
discontinuity.
The counter64 type should not be used for configuration
objects. A default statement should not be used for
attributes with a type value of counter64.
This type is in the value set and its semantics equivalent
to the Counter64 type of the SMIv2.";
reference
"RFC 2578: Structure of Management Information Version 2 (SMIv2)";
}
typedef zero-based-counter64 {
type yang:counter64;
default "0";
description
"The zero-based-counter64 type represents a counter64 which
has the defined `initial' value zero.
Objects of this type will be set to zero(0) on creation
and will thereafter count appropriate events, wrapping
back to zero(0) when the value 2^64 is reached.
Provided that an application discovers the new object within
the minimum time to wrap it can use the initial value as a
delta since it last polled the table of which this object is
part. It is important for a management station to be aware
of this minimum time and the actual time between polls, and
to discard data if the actual time is too long or there is
no defined minimum time.
Schoenwaelder Expires March 8, 2009 [Page 6]
Internet-Draft YANG-TYPES September 2008
This type is in the value set and its semantics equivalent
to the ZeroBasedCounter64 textual convention of the SMIv2.";
reference
"RFC 2856: Textual Conventions for Additional High Capacity
Data Types";
}
typedef gauge32 {
type uint32;
description
"The gauge32 type represents a non-negative integer, which
may increase or decrease, but shall never exceed a maximum
value, nor fall below a minimum value. The maximum value
can not be greater than 2^32-1 (4294967295 decimal), and
the minimum value can not be smaller than 0. The value of
a gauge32 has its maximum value whenever the information
being modeled is greater than or equal to its maximum
value, and has its minimum value whenever the information
being modeled is smaller than or equal to its minimum value.
If the information being modeled subsequently decreases
below (increases above) the maximum (minimum) value, the
gauge32 also decreases (increases).
This type is in the value set and its semantics equivalent
to the Counter32 type of the SMIv2.";
reference
"RFC 2578: Structure of Management Information Version 2 (SMIv2)";
}
typedef gauge64 {
type uint64;
description
"The gauge64 type represents a non-negative integer, which
may increase or decrease, but shall never exceed a maximum
value, nor fall below a minimum value. The maximum value
can not be greater than 2^64-1 (18446744073709551615), and
the minimum value can not be smaller than 0. The value of
a gauge64 has its maximum value whenever the information
being modeled is greater than or equal to its maximum
value, and has its minimum value whenever the information
being modeled is smaller than or equal to its minimum value.
If the information being modeled subsequently decreases
below (increases above) the maximum (minimum) value, the
gauge64 also decreases (increases).
This type is in the value set and its semantics equivalent
to the CounterBasedGauge64 SMIv2 textual convention defined
in RFC 2856";
Schoenwaelder Expires March 8, 2009 [Page 7]
Internet-Draft YANG-TYPES September 2008
reference
"RFC 2856: Textual Conventions for Additional High Capacity
Data Types";
}
/*** collection of identifier related types ***/
typedef object-identifier {
type string {
pattern '(([0-1](\.[1-3]?[0-9]))|(2.(0|([1-9]\d*))))'
+ '(\.(0|([1-9]\d*)))*';
}
description
"The object-identifier type represents administratively
assigned names in a registration-hierarchical-name tree.
Values of this type are denoted as a sequence of numerical
non-negative sub-identifier values. Each sub-identifier
value MUST NOT exceed 2^32-1 (4294967295). Sub-identifiers
are separated by single dots and without any intermediate
white space.
Although the number of sub-identifiers is not limited,
module designers should realize that there may be
implementations that stick with the SMIv2 limit of 128
sub-identifiers.
This type is a superset of the SMIv2 OBJECT IDENTIFIER type
since it is not restricted to 128 sub-identifiers.";
reference
"ISO/IEC 9834-1: Information technology -- Open Systems
Interconnection -- Procedures for the operation of OSI
Registration Authorities: General procedures and top
arcs of the ASN.1 Object Identifier tree";
}
typedef object-identifier-128 {
type object-identifier {
pattern '\d*(.\d){1,127}';
}
description
"This type represents object-identifiers restricted to 128
sub-identifiers.
This type is in the value set and its semantics equivalent to
the OBJECT IDENTIFIER type of the SMIv2.";
reference
"RFC 2578: Structure of Management Information Version 2 (SMIv2)";
Schoenwaelder Expires March 8, 2009 [Page 8]
Internet-Draft YANG-TYPES September 2008
}
/*** collection of date and time related types ***/
typedef date-and-time {
type string {
pattern '\d{4}-\d{2}-\d{2}T\d{2}:\d{2}:\d{2}(\.\d+)?'
+ '(Z|(\+|-)\d{2}:\d{2})';
}
description
'The date-and-time type is a profile of the ISO 8601
standard for representation of dates and times using the
Gregorian calendar. The format is most easily described
using the following ABFN (see RFC 3339):
date-fullyear = 4DIGIT
date-month = 2DIGIT ; 01-12
date-mday = 2DIGIT ; 01-28, 01-29, 01-30, 01-31
time-hour = 2DIGIT ; 00-23
time-minute = 2DIGIT ; 00-59
time-second = 2DIGIT ; 00-58, 00-59, 00-60
time-secfrac = "." 1*DIGIT
time-numoffset = ("+" / "-") time-hour ":" time-minute
time-offset = "Z" / time-numoffset
partial-time = time-hour ":" time-minute ":" time-second
[time-secfrac]
full-date = date-fullyear "-" date-month "-" date-mday
full-time = partial-time time-offset
date-time = full-date "T" full-time
The date-and-time type is compatible with the dateTime XML
schema type except that dateTime allows negative years
which are not allowed by RFC 3339.
This type is not equivalent to the DateAndTime textual
convention of the SMIv2 since RFC 3339 uses a different
separator between full-date and full-time and provides
higher resolution of time-secfrac.';
reference
"RFC 3339: Date and Time on the Internet: Timestamps
RFC 2579: Textual Conventions for SMIv2";
}
typedef timeticks {
type uint32;
description
Schoenwaelder Expires March 8, 2009 [Page 9]
Internet-Draft YANG-TYPES September 2008
"The timeticks type represents a non-negative integer which
represents the time, modulo 2^32 (4294967296 decimal), in
hundredths of a second between two epochs. When objects
are defined which use this type, the description of the
object identifies both of the reference epochs.
This type is in the value set and its semantics equivalent to
the TimeStamp textual convention of the SMIv2.";
reference
"RFC 2579: Textual Conventions for SMIv2";
}
typedef timestamp {
type yang:timeticks;
description
"The timestamp type represents the value of an associated
timeticks object at which a specific occurrence happened.
The specific occurrence must be defined in the description
of any object defined using this type. When the specific
occurrence occurred prior to the last time the associated
timeticks attribute was zero, then the timestamp value is
zero. Note that this requires all timestamp values to be
reset to zero when the value of the associated timeticks
attribute reaches 497+ days and wraps around to zero.
The associated timeticks object must be specified
in the description of any object using this type.
This type is in the value set and its semantics equivalent to
the TimeStamp textual convention of the SMIv2.";
reference
"RFC 2579: Textual Conventions for SMIv2";
}
/*** collection of generic address types ***/
typedef phys-address {
type string {
pattern '([0-9a0-fA-F]{2}(:[0-9a0-fA-F]{2})*)?';
}
description
"Represents media- or physical-level addresses represented
as a sequence octets, each octet represented by two hexadecimal
numbers. Octets are separated by colons.
This type is in the value set and its semantics equivalent to
the PhysAddress textual convention of the SMIv2.";
reference
Schoenwaelder Expires March 8, 2009 [Page 10]
Internet-Draft YANG-TYPES September 2008
"RFC 2579: Textual Conventions for SMIv2";
}
}
Schoenwaelder Expires March 8, 2009 [Page 11]
Internet-Draft YANG-TYPES September 2008
3. Internet Specific Derived Types
module inet-types {
namespace "urn:ietf:params:xml:ns:yang:inet-types";
prefix "inet";
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/netmod/>
WG List: <mailto:netmod@ietf.org>
WG Chair: David Partain
<mailto:david.partain@ericsson.com>
WG Chair: David Harrington
<mailto:ietfdbh@comcast.net>
Editor: Juergen Schoenwaelder
<mailto:j.schoenwaelder@jacobs-university.de>";
description
"This module contains a collection of generally useful derived
YANG data types for Internet addresses and related things.
Copyright (C) The IETF Trust (2008). This version of this
YANG module is part of RFC XXXX; see the RFC itself for full
legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove this note
revision 2008-08-26 {
description
"Initial revision, published as RFC XXXX.";
}
// RFC Ed.: replace XXXX with actual RFC number and remove this note
/*** collection of protocol field related types ***/
typedef ip-version {
type enumeration {
enum unknown {
value "0";
description
"An unknown or unspecified version of the Internet protocol.";
}
enum ipv4 {
Schoenwaelder Expires March 8, 2009 [Page 12]
Internet-Draft YANG-TYPES September 2008
value "1";
description
"The IPv4 protocol as defined in RFC 791.";
}
enum ipv6 {
value "2";
description
"The IPv6 protocol as defined in RFC 2460.";
}
}
description
"This value represents the version of the IP protocol.
This type is in the value set and its semantics equivalent
to the InetVersion textual convention of the SMIv2. However,
the lexical appearance is different from the InetVersion
textual convention.";
reference
"RFC 791: Internet Protocol
RFC 2460: Internet Protocol, Version 6 (IPv6) Specification
RFC 4001: Textual Conventions for Internet Network Addresses";
}
typedef dscp {
type uint8 {
range "0..63";
}
description
"The dscp type represents a Differentiated Services Code-Point
that may be used for marking a traffic stream.
This type is in the value set and its semantics equivalent
to the Dscp textual convention of the SMIv2.";
reference
"RFC 3289: Management Information Base for the Differentiated
Services Architecture
RFC 2474: Definition of the Differentiated Services Field
(DS Field) in the IPv4 and IPv6 Headers
RFC 2780: IANA Allocation Guidelines For Values In
the Internet Protocol and Related Headers";
}
typedef flow-label {
type uint32 {
range "0..1048575";
}
description
"The flow-label type represents flow identifier or Flow Label
Schoenwaelder Expires March 8, 2009 [Page 13]
Internet-Draft YANG-TYPES September 2008
in an IPv6 packet header that may be used to discriminate
traffic flows.
This type is in the value set and its semantics equivalent
to the IPv6FlowLabel textual convention of the SMIv2.";
reference
"RFC 3595: Textual Conventions for IPv6 Flow Label
RFC 2460: Internet Protocol, Version 6 (IPv6) Specification";
}
typedef port-number {
type uint16 {
range "1..65535";
}
description
"The port-number type represents a 16-bit port number of an
Internet transport layer protocol such as UDP, TCP, DCCP or
SCTP. Port numbers are assigned by IANA. A current list of
all assignments is available from <http://www.iana.org/>.
Note that the value zero is not a valid port number. A union
type might be used in situations where the value zero is
meaningful.
This type is in the value set and its semantics equivalent
to the InetPortNumber textual convention of the SMIv2.";
reference
"RFC 768: User Datagram Protocol
RFC 793: Transmission Control Protocol
RFC 2960: Stream Control Transmission Protocol
RFC 4340: Datagram Congestion Control Protocol (DCCP)
RFC 4001: Textual Conventions for Internet Network Addresses";
}
/*** collection of autonomous system related types ***/
typedef autonomous-system-number {
type uint32;
description
"The as-number type represents autonomous system numbers
which identify an Autonomous System (AS). An AS is a set
of routers under a single technical administration, using
an interior gateway protocol and common metrics to route
packets within the AS, and using an exterior gateway
protocol to route packets to other ASs'. IANA maintains
; the AS number space and has delegated large parts to the
regional registries.
Schoenwaelder Expires March 8, 2009 [Page 14]
Internet-Draft YANG-TYPES September 2008
Autonomous system numbers are currently limited to 16 bits
(0..65535). There is however work in progress to enlarge
the autonomous system number space to 32 bits. This
textual convention therefore uses an uint32 base type
without a range restriction in order to support a larger
autonomous system number space.
This type is in the value set and its semantics equivalent
to the InetAutonomousSystemNumber textual convention of
the SMIv2.";
reference
"RFC 1930: Guidelines for creation, selection, and registration
of an Autonomous System (AS)
RFC 4271: A Border Gateway Protocol 4 (BGP-4)
RFC 4001: Textual Conventions for Internet Network Addresses";
}
/*** collection of IP address and hostname related types ***/
typedef ip-address {
type union {
type inet:ipv4-address;
type inet:ipv6-address;
}
description
"The ip-address type represents an IP address and is IP
version neutral. The format of the textual representations
implies the IP version.";
}
typedef ipv4-address {
type string {
pattern '((0'
+ '|(1[0-9]{0,2})'
+ '|(2(([0-4][0-9]?)|(5[0-5]?)|([6-9]?)))'
+ '|([3-9][0-9]?)'
+ ')'
+ '\.){3}'
+ '(0'
+ '|(1[0-9]{0,2})'
+ '|(2(([0-4][0-9]?)|(5[0-5]?)|([6-9]?)))'
+ '|([3-9][0-9]?)'
+ ')(%[\p{N}\p{L}]+)?';
}
description
"The ipv4-address type represents an IPv4 address in
dotted-quad notation. The IPv4 address may include a zone
index, separated by a % sign.
Schoenwaelder Expires March 8, 2009 [Page 15]
Internet-Draft YANG-TYPES September 2008
The zone index is used to disambiguate identical address
values. For link-local addresses, the zone index will
typically be the interface index number or the name of an
interface. If the zone index is not present, the default
zone of the device will be used.";
}
typedef ipv6-address {
type string {
pattern
/* full */
'((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})'
+ '(%[\p{N}\p{L}]+)?)'
/* mixed */
+ '|((([0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.'
+ '[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '(%[\p{N}\p{L}]+)?)'
/* shortened */
+ '|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '(%[\p{N}\p{L}]+)?)'
/* shortened mixed */
+ '|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '(([0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '(%[\p{N}\p{L}]+)?)';
}
description
"The ipv6-address type represents an IPv6 address in full,
mixed, shortened and shortened mixed notation. The IPv6
address may include a zone index, separated by a % sign.
The zone index is used to disambiguate identical address
values. For link-local addresses, the zone index will
typically be the interface index number or the name of an
interface. If the zone index is not present, the default
zone of the device will be used.";
reference
"RFC 4007: IPv6 Scoped Address Architecture";
}
// [TODO: The pattern needs to be checked; once YANG supports
// multiple pattern, we can perhaps be more precise.]
typedef ip-prefix {
type union {
type inet:ipv4-prefix;
type inet:ipv6-prefix;
Schoenwaelder Expires March 8, 2009 [Page 16]
Internet-Draft YANG-TYPES September 2008
}
description
"The ip-prefix type represents an IP prefix and is IP
version neutral. The format of the textual representations
implies the IP version.";
}
typedef ipv4-prefix {
type string {
pattern '(([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])\.){3}'
+ '([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])'
+ '/\d+';
}
description
"The ipv4-prefix type represents an IPv4 address prefix.
The prefix length is given by the number following the
slash character and must be less than or equal to 32.
A prefix length value of n corresponds to an IP address
mask which has n contiguous 1-bits from the most
significant bit (MSB) and all other bits set to 0.
The IPv4 address represented in dotted quad notation
should have all bits that do not belong to the prefix
set to zero.";
}
typedef ipv6-prefix {
type string {
pattern
/* full */
'((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})'
+ '/\d+)'
/* mixed */
+ '|((([0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.'
+ '[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '/\d+)'
/* shortened */
+ '|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '/\d+)'
/* shortened mixed */
+ '|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '(([0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '/\d+)';
}
description
Schoenwaelder Expires March 8, 2009 [Page 17]
Internet-Draft YANG-TYPES September 2008
"The ipv6-prefix type represents an IPv6 address prefix.
The prefix length is given by the number following the
slash character and must be less than or equal 128.
A prefix length value of n corresponds to an IP address
mask which has n contiguous 1-bits from the most
significant bit (MSB) and all other bits set to 0.
The IPv6 address should have all bits that do not belong
to the prefix set to zero.";
}
// [TODO: The pattern needs to be checked; once YANG supports
// multiple pattern, we can perhaps be more precise.]
/*** collection of domain name and URI types ***/
typedef domain-name {
type string {
pattern '([a-zA-Z0-9][a-zA-Z0-9\-]*[a-zA-Z0-9]\.)*'
+ '[a-zA-Z0-9][a-zA-Z0-9\-]*[a-zA-Z0-9]';
}
description
"The domain-name type represents a DNS domain name. The
name SHOULD be fully qualified whenever possible.
The description clause of objects using the domain-name
type MUST describe how (and when) these names are
resolved to IP addresses.
Note that the resolution of a domain-name value may
require to query multiple DNS records (e.g., A for IPv4
and AAAA for IPv6). The order of the resolution process
and which DNS record takes precedence depends on the
configuration of the resolver.";
reference
"RFC 1034: Domain Names - Concepts and Facilities
RFC 1123: Requirements for Internet Hosts -- Application
and Support";
}
// [TODO: RFC 2181 says there are no restrictions on DNS
// labels. Need to check whether the pattern is too
// restrictive.]
typedef host {
type union {
type inet:ip-address;
Schoenwaelder Expires March 8, 2009 [Page 18]
Internet-Draft YANG-TYPES September 2008
type inet:domain-name;
}
description
"The host type represents either an IP address or a DNS
domain name.";
}
typedef uri {
type string; // [TODO: add the regex from RFC 3986 here?]
description
"The uri type represents a Uniform Resource Identifier
(URI) as defined by STD 66.
Objects using the uri type must be in US-ASCII encoding,
and MUST be normalized as described by RFC 3986 Sections
6.2.1, 6.2.2.1, and 6.2.2.2. All unnecessary
percent-encoding is removed, and all case-insensitive
characters are set to lowercase except for hexadecimal
digits, which are normalized to uppercase as described in
Section 6.2.2.1.
The purpose of this normalization is to help provide
unique URIs. Note that this normalization is not
sufficient to provide uniqueness. Two URIs that are
textually distinct after this normalization may still be
equivalent.
Objects using the uri type may restrict the schemes that
they permit. For example, 'data:' and 'urn:' schemes
might not be appropriate.
A zero-length URI is not a valid URI. This can be used to
express 'URI absent' where required
This type is in the value set and its semantics equivalent
to the Uri textual convention of the SMIv2.";
reference
"RFC 3986: Uniform Resource Identifier (URI): Generic Syntax
RFC 3305: Report from the Joint W3C/IETF URI Planning Interest
Group: Uniform Resource Identifiers (URIs), URLs,
and Uniform Resource Names (URNs): Clarifications
and Recommendations
RFC 5017: MIB Textual Conventions for Uniform Resource
Identifiers (URIs)";
}
}
Schoenwaelder Expires March 8, 2009 [Page 19]
Internet-Draft YANG-TYPES September 2008
4. IEEE Specific Derived Types
module ieee-types {
namespace "urn:ietf:params:xml:ns:yang:ieee-types";
prefix "ieee";
import yang-types { prefix yang; }
organization
"IETF NETMOD (NETCONF Data Modeling Language) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/netmod/>
WG List: <mailto:netmod@ietf.org>
WG Chair: David Partain
<mailto:david.partain@ericsson.com>
WG Chair: David Harrington
<mailto:ietfdbh@comcast.net>
Editor: Juergen Schoenwaelder
<mailto:j.schoenwaelder@jacobs-university.de>";
description
"This module contains a collection of generally useful derived
YANG data types for IEEE 802 addresses and related things.
Copyright (C) The IETF Trust (2008). This version of this
YANG module is part of RFC XXXX; see the RFC itself for full
legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove this note
revision 2008-08-22 {
description
"Initial revision, published as RFC XXXX";
}
// RFC Ed.: replace XXXX with actual RFC number and remove this note
/*** collection of IEEE address type definitions ***/
typedef mac-address {
type string {
pattern '[0-9a-fA-F]{2}(:[0-9a-fA-F]{2}){5}';
}
description
"The mac-address type represents an 802 MAC address represented
Schoenwaelder Expires March 8, 2009 [Page 20]
Internet-Draft YANG-TYPES September 2008
in the `canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though 802.5
(in contrast to other 802.x protocols) requires MAC addresses
to be transmitted most significant bit first.
This type is in the value set and its semantics equivalent to
the MacAddress textual convention of the SMIv2.";
reference
"RFC 2579: Textual Conventions for SMIv2";
}
/*** collection of IEEE 802 related identifier types ***/
typedef bridgeid {
type string {
pattern '[0-9a-fA-F]{4}(:[0-9a-fA-F]{2}){6}';
}
description
"The bridgeid type represents identifiers that uniquely
identify a bridge. Its first four hexadecimal digits
contain a priority value followed by a colon. The
remaining characters contain the MAC address used to
refer to a bridge in a unique fashion (typically, the
numerically smallest MAC address of all ports on the
bridge).
This type is in the value set and its semantics equivalent
to the BridgeId textual convention of the SMIv2. However,
since the BridgeId textual convention does not prescribe
a lexical representation, the appearance might be different.";
reference
"RFC 4188: Definitions of Managed Objects for Bridges";
}
typedef vlanid {
type uint16 {
range "1..4094";
}
description
"The vlanid type uniquely identifies a VLAN. This is the
12-bit VLAN-ID used in the VLAN Tag header. The range is
defined by the referenced specification.
This type is in the value set and its semantics equivalent to
the VlanId textual convention of the SMIv2.";
reference
"IEEE Std 802.1Q 2003 Edition: Virtual Bridged Local
Area Networks
Schoenwaelder Expires March 8, 2009 [Page 21]
Internet-Draft YANG-TYPES September 2008
RFC 4363: Definitions of Managed Objects for Bridges with
Traffic Classes, Multicast Filtering, and Virtual
LAN Extensions";
}
}
Schoenwaelder Expires March 8, 2009 [Page 22]
Internet-Draft YANG-TYPES September 2008
5. IANA Considerations
A registry for standard YANG modules shall be set up. The name of
the registry is "IETF YANG Modules" and the registry shall record for
each entry the unique name of a YANG module, the assigned XML
namespace from the YANG URI Scheme, and a reference to the module's
documentation (typically and RFC). Allocations require IETF Review
as defined in [RFC5226]. The initial assignements are:
YANG Module XML namespace Reference
----------- -------------------------------------- ---------
yang-types urn:ietf:params:xml:ns:yang:yang-types RFC XXXX
inet-types urn:ietf:params:xml:ns:yang:inet-types RFC XXXX
ieee-types urn:ietf:params:xml:ns:yang:ieee-types RFC XXXX
RFC Ed.: replace XXXX with actual RFC number and remove this note
This document registers three URIs1 in the IETF XML registry
[RFC3688]. Following the format in RFC 3688, the following
registration is requested.
URI: urn:ietf:params:xml:ns:yang:yang-types
URI: urn:ietf:params:xml:ns:yang:inet-types
URI: urn:ietf:params:xml:ns:yang:ieee-types
Registrant Contact: The NETMOD WG of the IETF.
XML: N/A, the requested URI is an XML namespace.
Schoenwaelder Expires March 8, 2009 [Page 23]
Internet-Draft YANG-TYPES September 2008
6. Security Considerations
This document defines common data types using the YANG data modeling
language. The definitions themselves have no security impact on the
Internet but the usage of these definitions in concrete YANG modules
might have. The security considerations spelled out in the YANG
specification [YANG] apply for this document as well.
Schoenwaelder Expires March 8, 2009 [Page 24]
Internet-Draft YANG-TYPES September 2008
7. Contributors
The following people all contributed significantly to the initial
version of this draft:
- Andy Bierman (andybierman.com)
- Martin Bjorklund (Tail-f Systems)
- Balazs Lengyel (Ericsson)
- David Partain (Ericsson)
- Phil Shafer (Juniper Networks)
Schoenwaelder Expires March 8, 2009 [Page 25]
Internet-Draft YANG-TYPES September 2008
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
January 2004.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
[YANG] Bjorklund, M., Ed., "YANG - A data modeling language for
NETCONF", draft-ietf-netmod-yang-01 (work in progress).
8.2. Informative References
[802.1Q] ANSI/IEEE Standard 802.1Q, "IEEE Standards for Local and
Metropolitan Area Networks: Virtual Bridged Local Area
Networks", 2003.
[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
September 1981.
[RFC0793] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, September 1981.
[RFC1034] Mockapetris, P., "Domain names - concepts and facilities",
STD 13, RFC 1034, November 1987.
[RFC1123] Braden, R., "Requirements for Internet Hosts - Application
and Support", STD 3, RFC 1123, October 1989.
[RFC1930] Hawkinson, J. and T. Bates, "Guidelines for creation,
selection, and registration of an Autonomous System (AS)",
BCP 6, RFC 1930, March 1996.
[RFC2021] Waldbusser, S., "Remote Network Monitoring Management
Information Base Version 2 using SMIv2", RFC 2021,
January 1997.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
Schoenwaelder Expires March 8, 2009 [Page 26]
Internet-Draft YANG-TYPES September 2008
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
December 1998.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
[RFC2780] Bradner, S. and V. Paxson, "IANA Allocation Guidelines For
Values In the Internet Protocol and Related Headers",
BCP 37, RFC 2780, March 2000.
[RFC2856] Bierman, A., McCloghrie, K., and R. Presuhn, "Textual
Conventions for Additional High Capacity Data Types",
RFC 2856, June 2000.
[RFC2960] Stewart, R., Xie, Q., Morneault, K., Sharp, C.,
Schwarzbauer, H., Taylor, T., Rytina, I., Kalla, M.,
Zhang, L., and V. Paxson, "Stream Control Transmission
Protocol", RFC 2960, October 2000.
[RFC3289] Baker, F., Chan, K., and A. Smith, "Management Information
Base for the Differentiated Services Architecture",
RFC 3289, May 2002.
[RFC3305] Mealling, M. and R. Denenberg, "Report from the Joint W3C/
IETF URI Planning Interest Group: Uniform Resource
Identifiers (URIs), URLs, and Uniform Resource Names
(URNs): Clarifications and Recommendations", RFC 3305,
August 2002.
[RFC3339] Klyne, G., Ed. and C. Newman, "Date and Time on the
Internet: Timestamps", RFC 3339, July 2002.
[RFC3595] Wijnen, B., "Textual Conventions for IPv6 Flow Label",
RFC 3595, September 2003.
[RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66,
RFC 3986, January 2005.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet Network
Schoenwaelder Expires March 8, 2009 [Page 27]
Internet-Draft YANG-TYPES September 2008
Addresses", RFC 4001, February 2005.
[RFC4007] Deering, S., Haberman, B., Jinmei, T., Nordmark, E., and
B. Zill, "IPv6 Scoped Address Architecture", RFC 4007,
March 2005.
[RFC4188] Norseth, K. and E. Bell, "Definitions of Managed Objects
for Bridges", RFC 4188, September 2005.
[RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
Protocol 4 (BGP-4)", RFC 4271, January 2006.
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340, March 2006.
[RFC4741] Enns, R., "NETCONF Configuration Protocol", RFC 4741,
December 2006.
[RFC5017] McWalter, D., "MIB Textual Conventions for Uniform
Resource Identifiers (URIs)", RFC 5017, September 2007.
Schoenwaelder Expires March 8, 2009 [Page 28]
Internet-Draft YANG-TYPES September 2008
Appendix A. XSD Translations
This appendix provides XML Schema (XSD) translations of the types
defined in this document. This appendix is informative and not
normative.
A.1. XSD of Core YANG Derived Types
<?xml version="1.0" encoding="UTF-8"?>
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema"
targetNamespace="urn:ietf:params:xml:ns:yang:yang-types"
xmlns="urn:ietf:params:xml:ns:yang:yang-types"
xmlns:yang="urn:ietf:params:xml:ns:yang:yang-types"
elementFormDefault="qualified"
attributeFormDefault="unqualified"
version="2008-08-26"
xml:lang="en">
<xs:annotation>
<xs:documentation>
This schema was generated from the YANG module yang-types
by pyang version 0.9.1.
The schema describes an instance document consisting of
the entire configuration data store and operational
data. This schema can thus NOT be used as-is to
validate NETCONF PDUs.
</xs:documentation>
</xs:annotation>
<xs:annotation>
<xs:documentation>
This module contains a collection of generally useful derived
YANG data types.
Copyright (C) The IETF Trust (2008). This version of this
YANG module is part of RFC XXXX; see the RFC itself for full
legal notices.
</xs:documentation>
</xs:annotation>
<!-- YANG typedefs -->
<xs:simpleType name="counter32">
<xs:annotation>
<xs:documentation>
The counter32 type represents a non-negative integer
which monotonically increases until it reaches a
maximum value of 2^32-1 (4294967295 decimal), when it
Schoenwaelder Expires March 8, 2009 [Page 29]
Internet-Draft YANG-TYPES September 2008
wraps around and starts increasing again from zero.
Counters have no defined `initial' value, and thus, a
single value of a counter has (in general) no information
content. Discontinuities in the monotonically increasing
value normally occur at re-initialization of the
management system, and at other times as specified in the
description of an object instance using this type. If
such other times can occur, for example, the creation of
an object instance of type counter32 at times other than
re-initialization, then a corresponding object should be
defined, with an appropriate type, to indicate the last
discontinuity.
The counter32 type should not be used for configuration
objects. A default statement should not be used for
attributes with a type value of counter32.
This type is in the value set and its semantics equivalent
to the Counter32 type of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedInt">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="zero-based-counter32">
<xs:annotation>
<xs:documentation>
The zero-based-counter32 type represents a counter32
which has the defined `initial' value zero.
Objects of this type will be set to zero(0) on creation
and will thereafter count appropriate events, wrapping
back to zero(0) when the value 2^32 is reached.
Provided that an application discovers the new object within
the minimum time to wrap it can use the initial value as a
delta since it last polled the table of which this object is
part. It is important for a management station to be aware
of this minimum time and the actual time between polls, and
to discard data if the actual time is too long or there is
no defined minimum time.
This type is in the value set and its semantics equivalent
to the ZeroBasedCounter32 textual convention of the SMIv2.
</xs:documentation>
Schoenwaelder Expires March 8, 2009 [Page 30]
Internet-Draft YANG-TYPES September 2008
</xs:annotation>
<xs:restriction base="yang:counter32">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="counter64">
<xs:annotation>
<xs:documentation>
The counter64 type represents a non-negative integer
which monotonically increases until it reaches a
maximum value of 2^64-1 (18446744073709551615), when
it wraps around and starts increasing again from zero.
Counters have no defined `initial' value, and thus, a
single value of a counter has (in general) no information
content. Discontinuities in the monotonically increasing
value normally occur at re-initialization of the
management system, and at other times as specified in the
description of an object instance using this type. If
such other times can occur, for example, the creation of
an object instance of type counter64 at times other than
re-initialization, then a corresponding object should be
defined, with an appropriate type, to indicate the last
discontinuity.
The counter64 type should not be used for configuration
objects. A default statement should not be used for
attributes with a type value of counter64.
This type is in the value set and its semantics equivalent
to the Counter64 type of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedLong">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="zero-based-counter64">
<xs:annotation>
<xs:documentation>
The zero-based-counter64 type represents a counter64 which
has the defined `initial' value zero.
Objects of this type will be set to zero(0) on creation
and will thereafter count appropriate events, wrapping
back to zero(0) when the value 2^64 is reached.
Schoenwaelder Expires March 8, 2009 [Page 31]
Internet-Draft YANG-TYPES September 2008
Provided that an application discovers the new object within
the minimum time to wrap it can use the initial value as a
delta since it last polled the table of which this object is
part. It is important for a management station to be aware
of this minimum time and the actual time between polls, and
to discard data if the actual time is too long or there is
no defined minimum time.
This type is in the value set and its semantics equivalent
to the ZeroBasedCounter64 textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="yang:counter64">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="gauge32">
<xs:annotation>
<xs:documentation>
The gauge32 type represents a non-negative integer, which
may increase or decrease, but shall never exceed a maximum
value, nor fall below a minimum value. The maximum value
can not be greater than 2^32-1 (4294967295 decimal), and
the minimum value can not be smaller than 0. The value of
a gauge32 has its maximum value whenever the information
being modeled is greater than or equal to its maximum
value, and has its minimum value whenever the information
being modeled is smaller than or equal to its minimum value.
If the information being modeled subsequently decreases
below (increases above) the maximum (minimum) value, the
gauge32 also decreases (increases).
This type is in the value set and its semantics equivalent
to the Counter32 type of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedInt">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="gauge64">
<xs:annotation>
<xs:documentation>
The gauge64 type represents a non-negative integer, which
may increase or decrease, but shall never exceed a maximum
value, nor fall below a minimum value. The maximum value
Schoenwaelder Expires March 8, 2009 [Page 32]
Internet-Draft YANG-TYPES September 2008
can not be greater than 2^64-1 (18446744073709551615), and
the minimum value can not be smaller than 0. The value of
a gauge64 has its maximum value whenever the information
being modeled is greater than or equal to its maximum
value, and has its minimum value whenever the information
being modeled is smaller than or equal to its minimum value.
If the information being modeled subsequently decreases
below (increases above) the maximum (minimum) value, the
gauge64 also decreases (increases).
This type is in the value set and its semantics equivalent
to the CounterBasedGauge64 SMIv2 textual convention defined
in RFC 2856
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedLong">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="object-identifier">
<xs:annotation>
<xs:documentation>
The object-identifier type represents administratively
assigned names in a registration-hierarchical-name tree.
Values of this type are denoted as a sequence of numerical
non-negative sub-identifier values. Each sub-identifier
value MUST NOT exceed 2^32-1 (4294967295). Sub-identifiers
are separated by single dots and without any intermediate
white space.
Although the number of sub-identifiers is not limited,
module designers should realize that there may be
implementations that stick with the SMIv2 limit of 128
sub-identifiers.
This type is a superset of the SMIv2 OBJECT IDENTIFIER type
since it is not restricted to 128 sub-identifiers.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="(([0-1](\.[1-3]?[0-9]))|(2.(0|([1-9]\d*))))(\
.(0|([1-9]\d*)))*"/>
</xs:restriction>
</xs:simpleType>
Schoenwaelder Expires March 8, 2009 [Page 33]
Internet-Draft YANG-TYPES September 2008
<xs:simpleType name="object-identifier-128">
<xs:annotation>
<xs:documentation>
This type represents object-identifiers restricted to 128
sub-identifiers.
This type is in the value set and its semantics equivalent to
the OBJECT IDENTIFIER type of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="object-identifier">
<xs:pattern value="\d*(.\d){1,127}"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="date-and-time">
<xs:annotation>
<xs:documentation>
The date-and-time type is a profile of the ISO 8601
standard for representation of dates and times using the
Gregorian calendar. The format is most easily described
using the following ABFN (see RFC 3339):
date-fullyear = 4DIGIT
date-month = 2DIGIT ; 01-12
date-mday = 2DIGIT ; 01-28, 01-29, 01-30, 01-31
time-hour = 2DIGIT ; 00-23
time-minute = 2DIGIT ; 00-59
time-second = 2DIGIT ; 00-58, 00-59, 00-60
time-secfrac = "." 1*DIGIT
time-numoffset = ("+" / "-") time-hour ":" time-minute
time-offset = "Z" / time-numoffset
partial-time = time-hour ":" time-minute ":" time-second
[time-secfrac]
full-date = date-fullyear "-" date-month "-" date-mday
full-time = partial-time time-offset
date-time = full-date "T" full-time
The date-and-time type is compatible with the dateTime XML
schema type except that dateTime allows negative years
which are not allowed by RFC 3339.
This type is not equivalent to the DateAndTime textual
convention of the SMIv2 since RFC 3339 uses a different
separator between full-date and full-time and provides
Schoenwaelder Expires March 8, 2009 [Page 34]
Internet-Draft YANG-TYPES September 2008
higher resolution of time-secfrac.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="\d{4}-\d{2}-\d{2}T\d{2}:\d{2}:\d{2}(\.\d+)?(Z
|(\+|-)\d{2}:\d{2})"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="timeticks">
<xs:annotation>
<xs:documentation>
The timeticks type represents a non-negative integer which
represents the time, modulo 2^32 (4294967296 decimal), in
hundredths of a second between two epochs. When objects
are defined which use this type, the description of the
object identifies both of the reference epochs.
This type is in the value set and its semantics equivalent to
the TimeStamp textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedInt">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="timestamp">
<xs:annotation>
<xs:documentation>
The timestamp type represents the value of an associated
timeticks object at which a specific occurrence happened.
The specific occurrence must be defined in the description
of any object defined using this type. When the specific
occurrence occurred prior to the last time the associated
timeticks attribute was zero, then the timestamp value is
zero. Note that this requires all timestamp values to be
reset to zero when the value of the associated timeticks
attribute reaches 497+ days and wraps around to zero.
The associated timeticks object must be specified
in the description of any object using this type.
This type is in the value set and its semantics equivalent to
the TimeStamp textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
Schoenwaelder Expires March 8, 2009 [Page 35]
Internet-Draft YANG-TYPES September 2008
<xs:restriction base="yang:timeticks">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="phys-address">
<xs:annotation>
<xs:documentation>
Represents media- or physical-level addresses represented
as a sequence octets, each octet represented by two hexadecimal
numbers. Octets are separated by colons.
This type is in the value set and its semantics equivalent to
the PhysAddress textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="([0-9a0-fA-F]{2}(:[0-9a0-fA-F]{2})*)?"/>
</xs:restriction>
</xs:simpleType>
</xs:schema>
A.2. XSD of Internet Specific Derived Types
<?xml version="1.0" encoding="UTF-8"?>
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema"
targetNamespace="urn:ietf:params:xml:ns:yang:inet-types"
xmlns="urn:ietf:params:xml:ns:yang:inet-types"
xmlns:inet="urn:ietf:params:xml:ns:yang:inet-types"
elementFormDefault="qualified"
attributeFormDefault="unqualified"
version="2008-08-26"
xml:lang="en">
<xs:annotation>
<xs:documentation>
This schema was generated from the YANG module inet-types
by pyang version 0.9.1.
The schema describes an instance document consisting of
the entire configuration data store and operational
data. This schema can thus NOT be used as-is to
validate NETCONF PDUs.
</xs:documentation>
</xs:annotation>
Schoenwaelder Expires March 8, 2009 [Page 36]
Internet-Draft YANG-TYPES September 2008
<xs:annotation>
<xs:documentation>
This module contains a collection of generally useful derived
YANG data types for Internet addresses and related things.
Copyright (C) The IETF Trust (2008). This version of this
YANG module is part of RFC XXXX; see the RFC itself for full
legal notices.
</xs:documentation>
</xs:annotation>
<!-- YANG typedefs -->
<xs:simpleType name="ip-version">
<xs:annotation>
<xs:documentation>
This value represents the version of the IP protocol.
This type is in the value set and its semantics equivalent
to the InetVersion textual convention of the SMIv2. However,
the lexical appearance is different from the InetVersion
textual convention.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:enumeration value="unknown"/>
<xs:enumeration value="ipv4"/>
<xs:enumeration value="ipv6"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="dscp">
<xs:annotation>
<xs:documentation>
The dscp type represents a Differentiated Services Code-Point
that may be used for marking a traffic stream.
This type is in the value set and its semantics equivalent
to the Dscp textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedByte">
<xs:minInclusive value="0"/>
<xs:maxInclusive value="63"/>
</xs:restriction>
</xs:simpleType>
Schoenwaelder Expires March 8, 2009 [Page 37]
Internet-Draft YANG-TYPES September 2008
<xs:simpleType name="flow-label">
<xs:annotation>
<xs:documentation>
The flow-label type represents flow identifier or Flow Label
in an IPv6 packet header that may be used to discriminate
traffic flows.
This type is in the value set and its semantics equivalent
to the IPv6FlowLabel textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedInt">
<xs:minInclusive value="0"/>
<xs:maxInclusive value="1048575"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="port-number">
<xs:annotation>
<xs:documentation>
The port-number type represents a 16-bit port number of an
Internet transport layer protocol such as UDP, TCP, DCCP or
SCTP. Port numbers are assigned by IANA. A current list of
all assignments is available from <http://www.iana.org/>.
Note that the value zero is not a valid port number. A union
type might be used in situations where the value zero is
meaningful.
This type is in the value set and its semantics equivalent
to the InetPortNumber textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedShort">
<xs:minInclusive value="1"/>
<xs:maxInclusive value="65535"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="autonomous-system-number">
<xs:annotation>
<xs:documentation>
The as-number type represents autonomous system numbers
which identify an Autonomous System (AS). An AS is a set
of routers under a single technical administration, using
an interior gateway protocol and common metrics to route
Schoenwaelder Expires March 8, 2009 [Page 38]
Internet-Draft YANG-TYPES September 2008
packets within the AS, and using an exterior gateway
protocol to route packets to other ASs'. IANA maintains
; the AS number space and has delegated large parts to the
regional registries.
Autonomous system numbers are currently limited to 16 bits
(0..65535). There is however work in progress to enlarge
the autonomous system number space to 32 bits. This
textual convention therefore uses an uint32 base type
without a range restriction in order to support a larger
autonomous system number space.
This type is in the value set and its semantics equivalent
to the InetAutonomousSystemNumber textual convention of
the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedInt">
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="ip-address">
<xs:annotation>
<xs:documentation>
The ip-address type represents an IP address and is IP
version neutral. The format of the textual representations
implies the IP version.
</xs:documentation>
</xs:annotation>
<xs:union>
<xs:simpleType>
<xs:restriction base="inet:ipv4-address">
</xs:restriction>
</xs:simpleType>
<xs:simpleType>
<xs:restriction base="inet:ipv6-address">
</xs:restriction>
</xs:simpleType>
</xs:union>
</xs:simpleType>
<xs:simpleType name="ipv4-address">
<xs:annotation>
<xs:documentation>
The ipv4-address type represents an IPv4 address in
dotted-quad notation. The IPv4 address may include a zone
Schoenwaelder Expires March 8, 2009 [Page 39]
Internet-Draft YANG-TYPES September 2008
index, separated by a % sign.
The zone index is used to disambiguate identical address
values. For link-local addresses, the zone index will
typically be the interface index number or the name of an
interface. If the zone index is not present, the default
zone of the device will be used.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="((0|(1[0-9]{0,2})|(2(([0-4][0-9]?)|(5[0-5]?)|
([6-9]?)))|([3-9][0-9]?))\.){3}(0|(1[0-9]{0,2}
)|(2(([0-4][0-9]?)|(5[0-5]?)|([6-9]?)))|([3-9]
[0-9]?))(%[\p{N}\p{L}]+)?"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="ipv6-address">
<xs:annotation>
<xs:documentation>
The ipv6-address type represents an IPv6 address in full,
mixed, shortened and shortened mixed notation. The IPv6
address may include a zone index, separated by a % sign.
The zone index is used to disambiguate identical address
values. For link-local addresses, the zone index will
typically be the interface index number or the name of an
interface. If the zone index is not present, the default
zone of the device will be used.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})(%
[\p{N}\p{L}]+)?)|((([0-9a-fA-F]{1,4}:){6})(([0
-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))
(%[\p{N}\p{L}]+)?)|((([0-9a-fA-F]{1,4}:)*([0-9
a-fA-F]{1,4}))*(::)(([0-9a-fA-F]{1,4}:)*([0-9a
-fA-F]{1,4}))*(%[\p{N}\p{L}]+)?)|((([0-9a-fA-F
]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)(([0-9a-fA-F]
{1,4}:)*([0-9a-fA-F]{1,4}))*(([0-9]{1,3}\.[0-9
]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))(%[\p{N}\p{L}]
+)?)"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="ip-prefix">
Schoenwaelder Expires March 8, 2009 [Page 40]
Internet-Draft YANG-TYPES September 2008
<xs:annotation>
<xs:documentation>
The ip-prefix type represents an IP prefix and is IP
version neutral. The format of the textual representations
implies the IP version.
</xs:documentation>
</xs:annotation>
<xs:union>
<xs:simpleType>
<xs:restriction base="inet:ipv4-prefix">
</xs:restriction>
</xs:simpleType>
<xs:simpleType>
<xs:restriction base="inet:ipv6-prefix">
</xs:restriction>
</xs:simpleType>
</xs:union>
</xs:simpleType>
<xs:simpleType name="ipv4-prefix">
<xs:annotation>
<xs:documentation>
The ipv4-prefix type represents an IPv4 address prefix.
The prefix length is given by the number following the
slash character and must be less than or equal to 32.
A prefix length value of n corresponds to an IP address
mask which has n contiguous 1-bits from the most
significant bit (MSB) and all other bits set to 0.
The IPv4 address represented in dotted quad notation
should have all bits that do not belong to the prefix
set to zero.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="(([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])\.){3
}([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])/\d+"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="ipv6-prefix">
<xs:annotation>
<xs:documentation>
The ipv6-prefix type represents an IPv6 address prefix.
The prefix length is given by the number following the
Schoenwaelder Expires March 8, 2009 [Page 41]
Internet-Draft YANG-TYPES September 2008
slash character and must be less than or equal 128.
A prefix length value of n corresponds to an IP address
mask which has n contiguous 1-bits from the most
significant bit (MSB) and all other bits set to 0.
The IPv6 address should have all bits that do not belong
to the prefix set to zero.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})/\
d+)|((([0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.[0-
9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))/\d+)|((([0-9
a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)(([0-9a
-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*/\d+)|((([0-
9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)(([0-9
a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(([0-9]{1,3
}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))/\d+)"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="domain-name">
<xs:annotation>
<xs:documentation>
The domain-name type represents a DNS domain name. The
name SHOULD be fully qualified whenever possible.
The description clause of objects using the domain-name
type MUST describe how (and when) these names are
resolved to IP addresses.
Note that the resolution of a domain-name value may
require to query multiple DNS records (e.g., A for IPv4
and AAAA for IPv6). The order of the resolution process
and which DNS record takes precedence depends on the
configuration of the resolver.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="([a-zA-Z0-9][a-zA-Z0-9\-]*[a-zA-Z0-9]\.)*[a-z
A-Z0-9][a-zA-Z0-9\-]*[a-zA-Z0-9]"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="host">
Schoenwaelder Expires March 8, 2009 [Page 42]
Internet-Draft YANG-TYPES September 2008
<xs:annotation>
<xs:documentation>
The host type represents either an IP address or a DNS
domain name.
</xs:documentation>
</xs:annotation>
<xs:union>
<xs:simpleType>
<xs:restriction base="inet:ip-address">
</xs:restriction>
</xs:simpleType>
<xs:simpleType>
<xs:restriction base="inet:domain-name">
</xs:restriction>
</xs:simpleType>
</xs:union>
</xs:simpleType>
<xs:simpleType name="uri">
<xs:annotation>
<xs:documentation>
The uri type represents a Uniform Resource Identifier
(URI) as defined by STD 66.
Objects using the uri type must be in US-ASCII encoding,
and MUST be normalized as described by RFC 3986 Sections
6.2.1, 6.2.2.1, and 6.2.2.2. All unnecessary
percent-encoding is removed, and all case-insensitive
characters are set to lowercase except for hexadecimal
digits, which are normalized to uppercase as described in
Section 6.2.2.1.
The purpose of this normalization is to help provide
unique URIs. Note that this normalization is not
sufficient to provide uniqueness. Two URIs that are
textually distinct after this normalization may still be
equivalent.
Objects using the uri type may restrict the schemes that
they permit. For example, 'data:' and 'urn:' schemes
might not be appropriate.
A zero-length URI is not a valid URI. This can be used to
express 'URI absent' where required
This type is in the value set and its semantics equivalent
to the Uri textual convention of the SMIv2.
Schoenwaelder Expires March 8, 2009 [Page 43]
Internet-Draft YANG-TYPES September 2008
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
</xs:restriction>
</xs:simpleType>
</xs:schema>
A.3. XSD of IEEE Specific Derived Types
<?xml version="1.0" encoding="UTF-8"?>
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema"
targetNamespace="urn:ietf:params:xml:ns:yang:ieee-types"
xmlns="urn:ietf:params:xml:ns:yang:ieee-types"
xmlns:ieee="urn:ietf:params:xml:ns:yang:ieee-types"
elementFormDefault="qualified"
attributeFormDefault="unqualified"
version="2008-08-22"
xml:lang="en"
xmlns:yang="urn:ietf:params:xml:ns:yang:yang-types">
<xs:import namespace="urn:ietf:params:xml:ns:yang:yang-types"
schemaLocation="yang-types.xsd"/>
<xs:annotation>
<xs:documentation>
This schema was generated from the YANG module ieee-types
by pyang version 0.9.1.
The schema describes an instance document consisting of
the entire configuration data store and operational
data. This schema can thus NOT be used as-is to
validate NETCONF PDUs.
</xs:documentation>
</xs:annotation>
<xs:annotation>
<xs:documentation>
This module contains a collection of generally useful derived
YANG data types for IEEE 802 addresses and related things.
Copyright (C) The IETF Trust (2008). This version of this
YANG module is part of RFC XXXX; see the RFC itself for full
legal notices.
</xs:documentation>
</xs:annotation>
Schoenwaelder Expires March 8, 2009 [Page 44]
Internet-Draft YANG-TYPES September 2008
<!-- YANG typedefs -->
<xs:simpleType name="mac-address">
<xs:annotation>
<xs:documentation>
The mac-address type represents an 802 MAC address represented
in the `canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though 802.5
(in contrast to other 802.x protocols) requires MAC addresses
to be transmitted most significant bit first.
This type is in the value set and its semantics equivalent to
the MacAddress textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="[0-9a-fA-F]{2}(:[0-9a-fA-F]{2}){5}"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="bridgeid">
<xs:annotation>
<xs:documentation>
The bridgeid type represents identifiers that uniquely
identify a bridge. Its first four hexadecimal digits
contain a priority value followed by a colon. The
remaining characters contain the MAC address used to
refer to a bridge in a unique fashion (typically, the
numerically smallest MAC address of all ports on the
bridge).
This type is in the value set and its semantics equivalent
to the BridgeId textual convention of the SMIv2. However,
since the BridgeId textual convention does not prescribe
a lexical representation, the appearance might be different.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:string">
<xs:pattern value="[0-9a-fA-F]{4}(:[0-9a-fA-F]{2}){6}"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType name="vlanid">
<xs:annotation>
<xs:documentation>
The vlanid type uniquely identifies a VLAN. This is the
Schoenwaelder Expires March 8, 2009 [Page 45]
Internet-Draft YANG-TYPES September 2008
12-bit VLAN-ID used in the VLAN Tag header. The range is
defined by the referenced specification.
This type is in the value set and its semantics equivalent to
the VlanId textual convention of the SMIv2.
</xs:documentation>
</xs:annotation>
<xs:restriction base="xs:unsignedShort">
<xs:minInclusive value="1"/>
<xs:maxInclusive value="4094"/>
</xs:restriction>
</xs:simpleType>
</xs:schema>
Schoenwaelder Expires March 8, 2009 [Page 46]
Internet-Draft YANG-TYPES September 2008
Appendix B. RelaxNG Translations
This appendix provides RelaxNG translations of the types defined in
this document. This appendix is informative and not normative.
B.1. RelaxNG of Core YANG Derived Types
namespace a = "http://relaxng.org/ns/compatibility/annotations/1.0"
namespace dc = "http://purl.org/dc/terms"
namespace dsrl = "http://purl.oclc.org/dsdl/dsrl"
namespace nm = "urn:ietf:params:xml:ns:netmod:dsdl-attrib:1"
namespace sch = "http://purl.oclc.org/dsdl/schematron"
dc:creator [
"IETF NETMOD (NETCONF Data Modeling Language) Working Group"
]
dc:description [
"This module contains a collection of generally useful derived\x{a}" ~
"YANG data types.\x{a}" ~
"\x{a}" ~
"Copyright (C) The IETF Trust (2008). This version of this\x{a}" ~
"YANG module is part of RFC XXXX; see the RFC itself for full\x{a}" ~
"legal notices."
]
dc:issued [ "2008-08-26" ]
dc:source [ "YANG module 'yang-types' (automatic translation)" ]
dc:contributor [
"WG Web: <http://tools.ietf.org/wg/netmod/>\x{a}" ~
"WG List: <mailto:netmod@ietf.org>\x{a}" ~
"\x{a}" ~
"WG Chair: David Partain\x{a}" ~
" <mailto:david.partain@ericsson.com>\x{a}" ~
"\x{a}" ~
"WG Chair: David Harrington\x{a}" ~
" <mailto:ietfdbh@comcast.net>\x{a}" ~
"\x{a}" ~
"Editor: Juergen Schoenwaelder\x{a}" ~
" <mailto:j.schoenwaelder@jacobs-university.de>"
]
## The counter32 type represents a non-negative integer
## which monotonically increases until it reaches a
## maximum value of 2^32-1 (4294967295 decimal), when it
## wraps around and starts increasing again from zero.
##
## Counters have no defined `initial' value, and thus, a
## single value of a counter has (in general) no information
## content. Discontinuities in the monotonically increasing
Schoenwaelder Expires March 8, 2009 [Page 47]
Internet-Draft YANG-TYPES September 2008
## value normally occur at re-initialization of the
## management system, and at other times as specified in the
## description of an object instance using this type. If
## such other times can occur, for example, the creation of
## an object instance of type counter32 at times other than
## re-initialization, then a corresponding object should be
## defined, with an appropriate type, to indicate the last
## discontinuity.
##
## The counter32 type should not be used for configuration
## objects. A default statement should not be used for
## attributes with a type value of counter32.
##
## This type is in the value set and its semantics equivalent
## to the Counter32 type of the SMIv2.
## See: RFC 2578: Structure of Management Information Version 2 (SMIv2)
__counter32 = xsd:unsignedInt
## The zero-based-counter32 type represents a counter32
## which has the defined `initial' value zero.
##
## Objects of this type will be set to zero(0) on creation
## and will thereafter count appropriate events, wrapping
## back to zero(0) when the value 2^32 is reached.
##
## Provided that an application discovers the new object within
## the minimum time to wrap it can use the initial value as a
## delta since it last polled the table of which this object is
## part. It is important for a management station to be aware
## of this minimum time and the actual time between polls, and
## to discard data if the actual time is too long or there is
## no defined minimum time.
##
## This type is in the value set and its semantics equivalent
## to the ZeroBasedCounter32 textual convention of the SMIv2.
## See: RFC 2021: Remote Network Monitoring Management Information
## Base Version 2 using SMIv2
__zero-based-counter32 = __counter32 >> dsrl:default-content [ "0" ]
## The counter64 type represents a non-negative integer
## which monotonically increases until it reaches a
## maximum value of 2^64-1 (18446744073709551615), when
## it wraps around and starts increasing again from zero.
##
## Counters have no defined `initial' value, and thus, a
## single value of a counter has (in general) no information
Schoenwaelder Expires March 8, 2009 [Page 48]
Internet-Draft YANG-TYPES September 2008
## content. Discontinuities in the monotonically increasing
## value normally occur at re-initialization of the
## management system, and at other times as specified in the
## description of an object instance using this type. If
## such other times can occur, for example, the creation of
## an object instance of type counter64 at times other than
## re-initialization, then a corresponding object should be
## defined, with an appropriate type, to indicate the last
## discontinuity.
##
## The counter64 type should not be used for configuration
## objects. A default statement should not be used for
## attributes with a type value of counter64.
##
## This type is in the value set and its semantics equivalent
## to the Counter64 type of the SMIv2.
## See: RFC 2578: Structure of Management Information Version 2 (SMIv2)
__counter64 = xsd:unsignedLong
## The zero-based-counter64 type represents a counter64 which
## has the defined `initial' value zero.
##
## Objects of this type will be set to zero(0) on creation
## and will thereafter count appropriate events, wrapping
## back to zero(0) when the value 2^64 is reached.
##
## Provided that an application discovers the new object within
## the minimum time to wrap it can use the initial value as a
## delta since it last polled the table of which this object is
## part. It is important for a management station to be aware
## of this minimum time and the actual time between polls, and
## to discard data if the actual time is too long or there is
## no defined minimum time.
##
## This type is in the value set and its semantics equivalent
## to the ZeroBasedCounter64 textual convention of the SMIv2.
## See: RFC 2856: Textual Conventions for Additional High Capacity
## Data Types
__zero-based-counter64 = __counter64 >> dsrl:default-content [ "0" ]
## The gauge32 type represents a non-negative integer, which
## may increase or decrease, but shall never exceed a maximum
## value, nor fall below a minimum value. The maximum value
## can not be greater than 2^32-1 (4294967295 decimal), and
## the minimum value can not be smaller than 0. The value of
## a gauge32 has its maximum value whenever the information
Schoenwaelder Expires March 8, 2009 [Page 49]
Internet-Draft YANG-TYPES September 2008
## being modeled is greater than or equal to its maximum
## value, and has its minimum value whenever the information
## being modeled is smaller than or equal to its minimum value.
## If the information being modeled subsequently decreases
## below (increases above) the maximum (minimum) value, the
## gauge32 also decreases (increases).
##
## This type is in the value set and its semantics equivalent
## to the Counter32 type of the SMIv2.
## See: RFC 2578: Structure of Management Information Version 2 (SMIv2)
__gauge32 = xsd:unsignedInt
## The gauge64 type represents a non-negative integer, which
## may increase or decrease, but shall never exceed a maximum
## value, nor fall below a minimum value. The maximum value
## can not be greater than 2^64-1 (18446744073709551615), and
## the minimum value can not be smaller than 0. The value of
## a gauge64 has its maximum value whenever the information
## being modeled is greater than or equal to its maximum
## value, and has its minimum value whenever the information
## being modeled is smaller than or equal to its minimum value.
## If the information being modeled subsequently decreases
## below (increases above) the maximum (minimum) value, the
## gauge64 also decreases (increases).
##
## This type is in the value set and its semantics equivalent
## to the CounterBasedGauge64 SMIv2 textual convention defined
## in RFC 2856
## See: RFC 2856: Textual Conventions for Additional High Capacity
## Data Types
__gauge64 = xsd:unsignedLong
## The object-identifier type represents administratively
## assigned names in a registration-hierarchical-name tree.
##
## Values of this type are denoted as a sequence of numerical
## non-negative sub-identifier values. Each sub-identifier
## value MUST NOT exceed 2^32-1 (4294967295). Sub-identifiers
## are separated by single dots and without any intermediate
## white space.
##
## Although the number of sub-identifiers is not limited,
## module designers should realize that there may be
## implementations that stick with the SMIv2 limit of 128
## sub-identifiers.
##
Schoenwaelder Expires March 8, 2009 [Page 50]
Internet-Draft YANG-TYPES September 2008
## This type is a superset of the SMIv2 OBJECT IDENTIFIER type
## since it is not restricted to 128 sub-identifiers.
## See: ISO/IEC 9834-1: Information technology -- Open Systems
## Interconnection -- Procedures for the operation of OSI
## Registration Authorities: General procedures and top
## arcs of the ASN.1 Object Identifier tree
__object-identifier =
xsd:string {
pattern =
"(([0-1](\.[1-3]?[0-9]))|(2.(0|([1-9]\d*))))(\.(0|([1-9]\d*)))*"
}
## This type represents object-identifiers restricted to 128
## sub-identifiers.
##
## This type is in the value set and its semantics equivalent to
## the OBJECT IDENTIFIER type of the SMIv2.
## See: RFC 2578: Structure of Management Information Version 2 (SMIv2)
__object-identifier-128 = __object-identifier
## The date-and-time type is a profile of the ISO 8601
## standard for representation of dates and times using the
## Gregorian calendar. The format is most easily described
## using the following ABFN (see RFC 3339):
##
## date-fullyear = 4DIGIT
## date-month = 2DIGIT ; 01-12
## date-mday = 2DIGIT ; 01-28, 01-29, 01-30, 01-31
## time-hour = 2DIGIT ; 00-23
## time-minute = 2DIGIT ; 00-59
## time-second = 2DIGIT ; 00-58, 00-59, 00-60
## time-secfrac = "." 1*DIGIT
## time-numoffset = ("+" / "-") time-hour ":" time-minute
## time-offset = "Z" / time-numoffset
##
## partial-time = time-hour ":" time-minute ":" time-second
## [time-secfrac]
## full-date = date-fullyear "-" date-month "-" date-mday
## full-time = partial-time time-offset
##
## date-time = full-date "T" full-time
##
## The date-and-time type is compatible with the dateTime XML
## schema type except that dateTime allows negative years
## which are not allowed by RFC 3339.
##
Schoenwaelder Expires March 8, 2009 [Page 51]
Internet-Draft YANG-TYPES September 2008
## This type is not equivalent to the DateAndTime textual
## convention of the SMIv2 since RFC 3339 uses a different
## separator between full-date and full-time and provides
## higher resolution of time-secfrac.
## See: RFC 3339: Date and Time on the Internet: Timestamps
## RFC 2579: Textual Conventions for SMIv2
__date-and-time =
xsd:string {
pattern =
"\d{4}-\d{2}-\d{2}T\d{2}:\d{2}:\d{2}(\.\d+)?(Z|(\+|-)\d{2}:\d{2})"
}
## The timeticks type represents a non-negative integer which
## represents the time, modulo 2^32 (4294967296 decimal), in
## hundredths of a second between two epochs. When objects
## are defined which use this type, the description of the
## object identifies both of the reference epochs.
##
## This type is in the value set and its semantics equivalent to
## the TimeStamp textual convention of the SMIv2.
## See: RFC 2579: Textual Conventions for SMIv2
__timeticks = xsd:unsignedInt
## The timestamp type represents the value of an associated
## timeticks object at which a specific occurrence happened.
## The specific occurrence must be defined in the description
## of any object defined using this type. When the specific
## occurrence occurred prior to the last time the associated
## timeticks attribute was zero, then the timestamp value is
## zero. Note that this requires all timestamp values to be
## reset to zero when the value of the associated timeticks
## attribute reaches 497+ days and wraps around to zero.
##
## The associated timeticks object must be specified
## in the description of any object using this type.
##
## This type is in the value set and its semantics equivalent to
## the TimeStamp textual convention of the SMIv2.
## See: RFC 2579: Textual Conventions for SMIv2
__timestamp = __timeticks
## Represents media- or physical-level addresses represented
## as a sequence octets, each octet represented by two hexadecimal
## numbers. Octets are separated by colons.
##
Schoenwaelder Expires March 8, 2009 [Page 52]
Internet-Draft YANG-TYPES September 2008
## This type is in the value set and its semantics equivalent to
## the PhysAddress textual convention of the SMIv2.
## See: RFC 2579: Textual Conventions for SMIv2
__phys-address =
xsd:string { pattern = "([0-9a0-fA-F]{2}(:[0-9a0-fA-F]{2})*)?" }
B.2. RelaxNG of Internet Specific Derived Types
namespace a = "http://relaxng.org/ns/compatibility/annotations/1.0"
namespace dc = "http://purl.org/dc/terms"
namespace dsrl = "http://purl.oclc.org/dsdl/dsrl"
namespace nm = "urn:ietf:params:xml:ns:netmod:dsdl-attrib:1"
namespace sch = "http://purl.oclc.org/dsdl/schematron"
dc:creator [
"IETF NETMOD (NETCONF Data Modeling Language) Working Group"
]
dc:description [
"This module contains a collection of generally useful derived\x{a}" ~
"YANG data types for Internet addresses and related things.\x{a}" ~
"\x{a}" ~
"Copyright (C) The IETF Trust (2008). This version of this\x{a}" ~
"YANG module is part of RFC XXXX; see the RFC itself for full\x{a}" ~
"legal notices."
]
dc:issued [ "2008-08-26" ]
dc:source [ "YANG module 'inet-types' (automatic translation)" ]
dc:contributor [
"WG Web: <http://tools.ietf.org/wg/netmod/>\x{a}" ~
"WG List: <mailto:netmod@ietf.org>\x{a}" ~
"\x{a}" ~
"WG Chair: David Partain\x{a}" ~
" <mailto:david.partain@ericsson.com>\x{a}" ~
"\x{a}" ~
"WG Chair: David Harrington\x{a}" ~
" <mailto:ietfdbh@comcast.net>\x{a}" ~
"\x{a}" ~
"Editor: Juergen Schoenwaelder\x{a}" ~
" <mailto:j.schoenwaelder@jacobs-university.de>"
]
## This value represents the version of the IP protocol.
##
## This type is in the value set and its semantics equivalent
## to the InetVersion textual convention of the SMIv2. However,
## the lexical appearance is different from the InetVersion
## textual convention.
Schoenwaelder Expires March 8, 2009 [Page 53]
Internet-Draft YANG-TYPES September 2008
## See: RFC 791: Internet Protocol
## RFC 2460: Internet Protocol, Version 6 (IPv6) Specification
## RFC 4001: Textual Conventions for Internet Network Addresses
__ip-version = "unknown" | "ipv4" | "ipv6"
## The dscp type represents a Differentiated Services Code-Point
## that may be used for marking a traffic stream.
##
## This type is in the value set and its semantics equivalent
## to the Dscp textual convention of the SMIv2.
## See: RFC 3289: Management Information Base for the Differentiated
## Services Architecture
## RFC 2474: Definition of the Differentiated Services Field
## (DS Field) in the IPv4 and IPv6 Headers
## RFC 2780: IANA Allocation Guidelines For Values In
## the Internet Protocol and Related Headers
__dscp = xsd:unsignedByte { minInclusive = "0" maxInclusive = "63" }
## The flow-label type represents flow identifier or Flow Label
## in an IPv6 packet header that may be used to discriminate
## traffic flows.
##
## This type is in the value set and its semantics equivalent
## to the IPv6FlowLabel textual convention of the SMIv2.
## See: RFC 3595: Textual Conventions for IPv6 Flow Label
## RFC 2460: Internet Protocol, Version 6 (IPv6) Specification
__flow-label =
xsd:unsignedInt { minInclusive = "0" maxInclusive = "1048575" }
## The port-number type represents a 16-bit port number of an
## Internet transport layer protocol such as UDP, TCP, DCCP or
## SCTP. Port numbers are assigned by IANA. A current list of
## all assignments is available from <http://www.iana.org/>.
##
## Note that the value zero is not a valid port number. A union
## type might be used in situations where the value zero is
## meaningful.
##
## This type is in the value set and its semantics equivalent
## to the InetPortNumber textual convention of the SMIv2.
## See: RFC 768: User Datagram Protocol
## RFC 793: Transmission Control Protocol
## RFC 2960: Stream Control Transmission Protocol
## RFC 4340: Datagram Congestion Control Protocol (DCCP)
## RFC 4001: Textual Conventions for Internet Network Addresses
Schoenwaelder Expires March 8, 2009 [Page 54]
Internet-Draft YANG-TYPES September 2008
__port-number =
xsd:unsignedShort { minInclusive = "1" maxInclusive = "65535" }
## The as-number type represents autonomous system numbers
## which identify an Autonomous System (AS). An AS is a set
## of routers under a single technical administration, using
## an interior gateway protocol and common metrics to route
## packets within the AS, and using an exterior gateway
## protocol to route packets to other ASs'. IANA maintains
## ; the AS number space and has delegated large parts to the
## regional registries.
##
## Autonomous system numbers are currently limited to 16 bits
## (0..65535). There is however work in progress to enlarge
## the autonomous system number space to 32 bits. This
## textual convention therefore uses an uint32 base type
## without a range restriction in order to support a larger
## autonomous system number space.
##
## This type is in the value set and its semantics equivalent
## to the InetAutonomousSystemNumber textual convention of
## the SMIv2.
## See: RFC 1930: Guidelines for creation, selection, and registration
## of an Autonomous System (AS)
## RFC 4271: A Border Gateway Protocol 4 (BGP-4)
## RFC 4001: Textual Conventions for Internet Network Addresses
__autonomous-system-number = xsd:unsignedInt
## The ip-address type represents an IP address and is IP
## version neutral. The format of the textual representations
## implies the IP version.
__ip-address = __ipv4-address | __ipv6-address
## The ipv4-address type represents an IPv4 address in
## dotted-quad notation. The IPv4 address may include a zone
## index, separated by a % sign.
##
## The zone index is used to disambiguate identical address
## values. For link-local addresses, the zone index will
## typically be the interface index number or the name of an
## interface. If the zone index is not present, the default
## zone of the device will be used.
__ipv4-address =
xsd:string {
pattern =
"((0|(1[0-9]{0,2})|(2(([0-4][0-9]?)|(5[0-5]?)|([6-9]?)"
~ "))|([3-9][0-9]?))\.){3}(0|(1[0-9]{0,2})|(2(([0-4][0-9]?)|(5["
Schoenwaelder Expires March 8, 2009 [Page 55]
Internet-Draft YANG-TYPES September 2008
~ "0-5]?)|([6-9]?)))|([3-9][0-9]?))(%[\p{N}\p{L}]+)?"
}
## The ipv6-address type represents an IPv6 address in full,
## mixed, shortened and shortened mixed notation. The IPv6
## address may include a zone index, separated by a % sign.
##
## The zone index is used to disambiguate identical address
## values. For link-local addresses, the zone index will
## typically be the interface index number or the name of an
## interface. If the zone index is not present, the default
## zone of the device will be used.
## See: RFC 4007: IPv6 Scoped Address Architecture
__ipv6-address =
xsd:string {
pattern =
"((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})(%[\p{N}\p"
~ "{L}]+)?)|((([0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.[0-9]{1,3}\."
~ "[0-9]{1,3}\.[0-9]{1,3}))(%[\p{N}\p{L}]+)?)|((([0-9a-fA-F]{1,"
~ "4}:)*([0-9a-fA-F]{1,4}))*(::)(([0-9a-fA-F]{1,4}:)*([0-9a-fA-"
~ "F]{1,4}))*(%[\p{N}\p{L}]+)?)|((([0-9a-fA-F]{1,4}:)*([0-9a-fA"
~ "-F]{1,4}))*(::)(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(([0"
~ "-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))(%[\p{N}\p{L}]"
~ "+)?)"
}
## The ip-prefix type represents an IP prefix and is IP
## version neutral. The format of the textual representations
## implies the IP version.
__ip-prefix = __ipv4-prefix | __ipv6-prefix
## The ipv4-prefix type represents an IPv4 address prefix.
## The prefix length is given by the number following the
## slash character and must be less than or equal to 32.
##
## A prefix length value of n corresponds to an IP address
## mask which has n contiguous 1-bits from the most
## significant bit (MSB) and all other bits set to 0.
##
## The IPv4 address represented in dotted quad notation
## should have all bits that do not belong to the prefix
## set to zero.
__ipv4-prefix =
xsd:string {
pattern =
"(([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])\.){3}([0-1]?"
~ "[0-9]?[0-9]|2[0-4][0-9]|25[0-5])/\d+"
Schoenwaelder Expires March 8, 2009 [Page 56]
Internet-Draft YANG-TYPES September 2008
}
## The ipv6-prefix type represents an IPv6 address prefix.
## The prefix length is given by the number following the
## slash character and must be less than or equal 128.
##
## A prefix length value of n corresponds to an IP address
## mask which has n contiguous 1-bits from the most
## significant bit (MSB) and all other bits set to 0.
##
## The IPv6 address should have all bits that do not belong
## to the prefix set to zero.
__ipv6-prefix =
xsd:string {
pattern =
"((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})/\d+)|(((["
~ "0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.["
~ "0-9]{1,3}))/\d+)|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*("
~ "::)(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*/\d+)|((([0-9a-f"
~ "A-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)(([0-9a-fA-F]{1,4}:)*([0"
~ "-9a-fA-F]{1,4}))*(([0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]"
~ "{1,3}))/\d+)"
}
## The domain-name type represents a DNS domain name. The
## name SHOULD be fully qualified whenever possible.
##
## The description clause of objects using the domain-name
## type MUST describe how (and when) these names are
## resolved to IP addresses.
##
## Note that the resolution of a domain-name value may
## require to query multiple DNS records (e.g., A for IPv4
## and AAAA for IPv6). The order of the resolution process
## and which DNS record takes precedence depends on the
## configuration of the resolver.
## See: RFC 1034: Domain Names - Concepts and Facilities
## RFC 1123: Requirements for Internet Hosts -- Application
## and Support
__domain-name =
xsd:string {
pattern =
"([a-zA-Z0-9][a-zA-Z0-9\-]*[a-zA-Z0-9]\.)*[a-zA-Z0-9]["
~ "a-zA-Z0-9\-]*[a-zA-Z0-9]"
}
## The host type represents either an IP address or a DNS
Schoenwaelder Expires March 8, 2009 [Page 57]
Internet-Draft YANG-TYPES September 2008
## domain name.
__host = __ip-address | __domain-name
## The uri type represents a Uniform Resource Identifier
## (URI) as defined by STD 66.
##
## Objects using the uri type must be in US-ASCII encoding,
## and MUST be normalized as described by RFC 3986 Sections
## 6.2.1, 6.2.2.1, and 6.2.2.2. All unnecessary
## percent-encoding is removed, and all case-insensitive
## characters are set to lowercase except for hexadecimal
## digits, which are normalized to uppercase as described in
## Section 6.2.2.1.
##
## The purpose of this normalization is to help provide
## unique URIs. Note that this normalization is not
## sufficient to provide uniqueness. Two URIs that are
## textually distinct after this normalization may still be
## equivalent.
##
## Objects using the uri type may restrict the schemes that
## they permit. For example, 'data:' and 'urn:' schemes
## might not be appropriate.
##
## A zero-length URI is not a valid URI. This can be used to
## express 'URI absent' where required
##
## This type is in the value set and its semantics equivalent
## to the Uri textual convention of the SMIv2.
## See: RFC 3986: Uniform Resource Identifier (URI): Generic Syntax
## RFC 3305: Report from the Joint W3C/IETF URI Planning Interest
## Group: Uniform Resource Identifiers (URIs), URLs,
## and Uniform Resource Names (URNs): Clarifications
## and Recommendations
## RFC 5017: MIB Textual Conventions for Uniform Resource
## Identifiers (URIs)
__uri = xsd:string
B.3. RelaxNG of IEEE Specific Derived Types
namespace a = "http://relaxng.org/ns/compatibility/annotations/1.0"
namespace dc = "http://purl.org/dc/terms"
namespace dsrl = "http://purl.oclc.org/dsdl/dsrl"
namespace nm = "urn:ietf:params:xml:ns:netmod:dsdl-attrib:1"
namespace sch = "http://purl.oclc.org/dsdl/schematron"
dc:creator [
Schoenwaelder Expires March 8, 2009 [Page 58]
Internet-Draft YANG-TYPES September 2008
"IETF NETMOD (NETCONF Data Modeling Language) Working Group"
]
dc:description [
"This module contains a collection of generally useful derived\x{a}" ~
"YANG data types for IEEE 802 addresses and related things.\x{a}" ~
"\x{a}" ~
"Copyright (C) The IETF Trust (2008). This version of this\x{a}" ~
"YANG module is part of RFC XXXX; see the RFC itself for full\x{a}" ~
"legal notices."
]
dc:issued [ "2008-08-22" ]
dc:source [ "YANG module 'ieee-types' (automatic translation)" ]
dc:contributor [
"WG Web: <http://tools.ietf.org/wg/netmod/>\x{a}" ~
"WG List: <mailto:netmod@ietf.org>\x{a}" ~
"\x{a}" ~
"WG Chair: David Partain\x{a}" ~
" <mailto:david.partain@ericsson.com>\x{a}" ~
"\x{a}" ~
"WG Chair: David Harrington\x{a}" ~
" <mailto:ietfdbh@comcast.net>\x{a}" ~
"\x{a}" ~
"Editor: Juergen Schoenwaelder\x{a}" ~
" <mailto:j.schoenwaelder@jacobs-university.de>"
]
## The mac-address type represents an 802 MAC address represented
## in the `canonical' order defined by IEEE 802.1a, i.e., as if it
## were transmitted least significant bit first, even though 802.5
## (in contrast to other 802.x protocols) requires MAC addresses
## to be transmitted most significant bit first.
##
## This type is in the value set and its semantics equivalent to
## the MacAddress textual convention of the SMIv2.
## See: RFC 2579: Textual Conventions for SMIv2
__mac-address =
xsd:string { pattern = "[0-9a-fA-F]{2}(:[0-9a-fA-F]{2}){5}" }
## The bridgeid type represents identifiers that uniquely
## identify a bridge. Its first four hexadecimal digits
## contain a priority value followed by a colon. The
## remaining characters contain the MAC address used to
## refer to a bridge in a unique fashion (typically, the
## numerically smallest MAC address of all ports on the
## bridge).
##
## This type is in the value set and its semantics equivalent
Schoenwaelder Expires March 8, 2009 [Page 59]
Internet-Draft YANG-TYPES September 2008
## to the BridgeId textual convention of the SMIv2. However,
## since the BridgeId textual convention does not prescribe
## a lexical representation, the appearance might be different.
## See: RFC 4188: Definitions of Managed Objects for Bridges
__bridgeid =
xsd:string { pattern = "[0-9a-fA-F]{4}(:[0-9a-fA-F]{2}){6}" }
## The vlanid type uniquely identifies a VLAN. This is the
## 12-bit VLAN-ID used in the VLAN Tag header. The range is
## defined by the referenced specification.
##
## This type is in the value set and its semantics equivalent to
## the VlanId textual convention of the SMIv2.
## See: IEEE Std 802.1Q 2003 Edition: Virtual Bridged Local
## Area Networks
## RFC 4363: Definitions of Managed Objects for Bridges with
## Traffic Classes, Multicast Filtering, and Virtual
## LAN Extensions
__vlanid =
xsd:unsignedShort { minInclusive = "1" maxInclusive = "4094" }
Schoenwaelder Expires March 8, 2009 [Page 60]
Internet-Draft YANG-TYPES September 2008
Author's Address
Juergen Schoenwaelder (editor)
Jacobs University
Email: j.schoenwaelder@jacobs-university.de
Schoenwaelder Expires March 8, 2009 [Page 61]
Internet-Draft YANG-TYPES September 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Schoenwaelder Expires March 8, 2009 [Page 62]
