NAT/Firewall NSIS Signaling Layer Protocol (NSLP)
draft-ietf-nsis-nslp-natfw-25

NSIS Working Group                                        M. Stiemerling
Internet-Draft                                                       NEC
Intended status: Standards Track                           H. Tschofenig
Expires: January 10, 2008                                            NSN
                                                                 C. Aoun
                                                               E. Davies
                                                        Folly Consulting
                                                            July 9, 2007


           NAT/Firewall NSIS Signaling Layer Protocol (NSLP)
                   draft-ietf-nsis-nslp-natfw-15.txt

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on January 10, 2008.

Copyright Notice

   Copyright (C) The IETF Trust (2007).









Stiemerling, et al.     Expires January 10, 2008                [Page 1]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Abstract

   This memo defines the NSIS Signaling Layer Protocol (NSLP) for
   Network Address Translators (NATs) and firewalls.  This NSLP allows
   hosts to signal on the data path for NATs and firewalls to be
   configured according to the needs of the application data flows.  It
   enables hosts behind NATs to obtain a public reachable address and
   hosts behind firewalls to receive data traffic.  The overall
   architecture is given by the framework and requirements defined by
   the Next Steps in Signaling (NSIS) working group.  The network
   scenarios, the protocol itself, and examples for path-coupled
   signaling are given in this memo.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  5
     1.1.  Terminology and Abbreviations  . . . . . . . . . . . . . .  7
     1.2.  Middleboxes  . . . . . . . . . . . . . . . . . . . . . . . 10
     1.3.  General Scenario for NATFW Traversal . . . . . . . . . . . 11

   2.  Network Deployment Scenarios using the NATFW NSLP  . . . . . . 13
     2.1.  Firewall Traversal . . . . . . . . . . . . . . . . . . . . 13
     2.2.  NAT with two private Networks  . . . . . . . . . . . . . . 14
     2.3.  NAT with Private Network on Sender Side  . . . . . . . . . 15
     2.4.  NAT with Private Network on Receiver Side Scenario . . . . 15
     2.5.  Both End Hosts behind twice-NATs . . . . . . . . . . . . . 16
     2.6.  Both End Hosts Behind Same NAT . . . . . . . . . . . . . . 17
     2.7.  Multihomed Network with NAT  . . . . . . . . . . . . . . . 18
     2.8.  Multihomed Network with Firewall . . . . . . . . . . . . . 19

   3.  Protocol Description . . . . . . . . . . . . . . . . . . . . . 20
     3.1.  Policy Rules . . . . . . . . . . . . . . . . . . . . . . . 20
     3.2.  Basic Protocol Overview  . . . . . . . . . . . . . . . . . 21
       3.2.1.  Message Types  . . . . . . . . . . . . . . . . . . . . 25
       3.2.2.  Classification of RESPONSE Messages  . . . . . . . . . 25
       3.2.3.  NATFW NSLP Signaling Sessions  . . . . . . . . . . . . 26
     3.3.  Basic Message Processing . . . . . . . . . . . . . . . . . 27
     3.4.  Calculation of Signaling Session Lifetime  . . . . . . . . 27
     3.5.  Message Sequencing . . . . . . . . . . . . . . . . . . . . 30
     3.6.  Authentication, Authorization, and Policy Decisions  . . . 31
     3.7.  Protocol Operations  . . . . . . . . . . . . . . . . . . . 32
       3.7.1.  Creating Signaling Sessions  . . . . . . . . . . . . . 32
       3.7.2.  Reserving External Addresses . . . . . . . . . . . . . 35
       3.7.3.  NATFW NSLP Signaling Session Refresh . . . . . . . . . 42
       3.7.4.  Deleting Signaling Sessions  . . . . . . . . . . . . . 43
       3.7.5.  Reporting Asynchronous Events  . . . . . . . . . . . . 44
       3.7.6.  Proxy Mode of Operation  . . . . . . . . . . . . . . . 46



Stiemerling, et al.     Expires January 10, 2008                [Page 2]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


     3.8.  De-Multiplexing at NATs  . . . . . . . . . . . . . . . . . 49
     3.9.  Reacting to Route Changes  . . . . . . . . . . . . . . . . 51
     3.10. Updating Policy Rules  . . . . . . . . . . . . . . . . . . 51

   4.  NATFW NSLP Message Components  . . . . . . . . . . . . . . . . 53
     4.1.  NSLP Header  . . . . . . . . . . . . . . . . . . . . . . . 53
     4.2.  NSLP Objects . . . . . . . . . . . . . . . . . . . . . . . 54
       4.2.1.  Signaling Session Lifetime Object  . . . . . . . . . . 55
       4.2.2.  External Address Object  . . . . . . . . . . . . . . . 55
       4.2.3.  Extended Flow Information Object . . . . . . . . . . . 56
       4.2.4.  Information Code Object  . . . . . . . . . . . . . . . 57
       4.2.5.  Nonce Object . . . . . . . . . . . . . . . . . . . . . 60
       4.2.6.  Message Sequence Number Object . . . . . . . . . . . . 60
       4.2.7.  Data Terminal Information Object . . . . . . . . . . . 61
       4.2.8.  ICMP Types Object  . . . . . . . . . . . . . . . . . . 62
     4.3.  Message Formats  . . . . . . . . . . . . . . . . . . . . . 63
       4.3.1.  CREATE . . . . . . . . . . . . . . . . . . . . . . . . 64
       4.3.2.  EXTERNAL (EXT) . . . . . . . . . . . . . . . . . . . . 64
       4.3.3.  RESPONSE . . . . . . . . . . . . . . . . . . . . . . . 65
       4.3.4.  NOTIFY . . . . . . . . . . . . . . . . . . . . . . . . 65

   5.  Security Considerations  . . . . . . . . . . . . . . . . . . . 67
     5.1.  Authorization Framework  . . . . . . . . . . . . . . . . . 67
       5.1.1.  Peer-to-Peer Relationship  . . . . . . . . . . . . . . 67
       5.1.2.  Intra-Domain Relationship  . . . . . . . . . . . . . . 68
       5.1.3.  End-to-Middle Relationship . . . . . . . . . . . . . . 69
     5.2.  Security Framework for the NAT/Firewall NSLP . . . . . . . 70
       5.2.1.  Security Protection between neighboring NATFW NSLP
               Nodes  . . . . . . . . . . . . . . . . . . . . . . . . 70
       5.2.2.  Security Protection between non-neighboring NATFW
               NSLP Nodes . . . . . . . . . . . . . . . . . . . . . . 71

   6.  IAB Considerations on UNSAF  . . . . . . . . . . . . . . . . . 73

   7.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 74

   8.  Open Issues  . . . . . . . . . . . . . . . . . . . . . . . . . 76

   9.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 77

   10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 78
     10.1. Normative References . . . . . . . . . . . . . . . . . . . 78
     10.2. Informative References . . . . . . . . . . . . . . . . . . 78

   Appendix A.  Selecting Signaling Destination Addresses for EXT . . 80

   Appendix B.  Applicability Statement on Data Receivers behind
                Firewalls . . . . . . . . . . . . . . . . . . . . . . 81



Stiemerling, et al.     Expires January 10, 2008                [Page 3]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   Appendix C.  Firewall and NAT Resources  . . . . . . . . . . . . . 83
     C.1.  Wildcarding of Policy Rules  . . . . . . . . . . . . . . . 83
     C.2.  Mapping to Firewall Rules  . . . . . . . . . . . . . . . . 83
     C.3.  Mapping to NAT Bindings  . . . . . . . . . . . . . . . . . 84
     C.4.  NSLP Handling of Twice-NAT . . . . . . . . . . . . . . . . 84

   Appendix D.  Assigned Numbers for Testing  . . . . . . . . . . . . 86

   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 87
   Intellectual Property and Copyright Statements . . . . . . . . . . 88









































Stiemerling, et al.     Expires January 10, 2008                [Page 4]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


1.  Introduction

   Firewalls and Network Address Translators (NAT) have both been used
   throughout the Internet for many years, and they will remain present
   for the foreseeable future.  Firewalls are used to protect networks
   against certain types of attacks from internal networks and the
   Internet, whereas NATs provide a virtual extension of the IP address
   space.  Both types of devices may be obstacles to some applications,
   since they only allow traffic created by a limited set of
   applications to traverse them, typically those that use protocols
   with relatively predetermined and static properties (e.g., most HTTP
   traffic, and other client/server applications).  Other applications,
   such as IP telephony and most other peer-to-peer applications, which
   have more dynamic properties, create traffic that is unable to
   traverse NATs and firewalls unassisted.  In practice, the traffic of
   many applications cannot traverse autonomous firewalls or NATs, even
   when they have additional functionality which attempts to restore the
   transparency of the network.

   Several solutions to enable applications to traverse such entities
   have been proposed and are currently in use.  Typically, application
   level gateways (ALG) have been integrated with the firewall or NAT to
   configure the firewall or NAT dynamically.  Another approach is
   middlebox communication (MIDCOM).  In this approach, ALGs external to
   the firewall or NAT configure the corresponding entity via the MIDCOM
   protocol [7].  Several other work-around solutions are available,
   such as STUN [15].  However, all of these approaches introduce other
   problems that are generally hard to solve, such as dependencies on
   the type of NAT implementation (full-cone, symmetric, etc), or
   dependencies on certain network topologies.

   NAT and firewall (NATFW) signaling shares a property with Quality of
   Service (QoS) signaling.  The signaling of both must reach any device
   on the data path that is involved in, respectively, NATFW or QoS
   treatment of data packets.  This means, that for both, NATFW and QoS,
   it is convenient if signaling travels path-coupled, meaning that the
   signaling messages follow exactly the same path that the data packets
   take.  RSVP [11] is an example of a current QoS signaling protocol
   that is path-coupled. [21] proposes the use of RSVP as firewall
   signaling protocol but does not include NATs.

   This memo defines a path-coupled signaling protocol for NAT and
   firewall configuration within the framework of NSIS, called the NATFW
   NSIS Signaling Layer Protocol (NSLP).  The general requirements for
   NSIS are defined in [5] and the general framework of NSIS is outlined
   in [4].  It introduces the split between an NSIS transport layer and
   an NSIS signaling layer.  The transport of NSLP messages is handled
   by an NSIS Network Transport Layer Protocol (NTLP, with General



Stiemerling, et al.     Expires January 10, 2008                [Page 5]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   Internet Signaling Transport (GIST) [2] being the implementation of
   the abstract NTLP).  The signaling logic for QoS and NATFW signaling
   is implemented in the different NSLPs.  The QoS NSLP is defined in
   [6].

   The NATFW NSLP is designed to request the dynamic configuration of
   NATs and/or firewalls along the data path.  Dynamic configuration
   includes enabling data flows to traverse these devices without being
   obstructed, as well as blocking of particular data flows at inbound
   firewalls.  Enabling data flows requires the loading of firewall
   rules with an action that allows the data flow packets to be
   forwarded and creating NAT bindings.  Blocking of data flows requires
   the loading of firewalls rules with an action that will deny
   forwarding of the data flow packets.  A simplified example for
   enabling data flows: A source host sends a NATFW NSLP signaling
   message towards its data destination.  This message follows the data
   path.  Every NATFW NSLP-enabled NAT/firewall along the data path
   intercepts these messages, processes them, and configures itself
   accordingly.  Thereafter, the actual data flow can traverse all these
   configured firewalls/NATs.

   It is necessary to distinguish between two different basic scenarios
   when operating the NATFW NSLP, independent of the type of the
   middleboxes to be configured.

   1.  Both, data sender and data receiver, are NSIS NATFW NSLP aware.
       This includes the cases where the data sender is logically
       decomposed from the NSIS initiator or the data receiver logically
       decomposed from the NSIS receiver, but both sides support NSIS.
       This scenario assumes deployment of NSIS all over the Internet,
       or at least at all NATs and firewalls.  This scenario is used as
       base assumption, if not otherwise noted.

   2.  Only one end host or region of the network is NSIS NATFW NSLP
       aware, either data receiver or data sender.  This scenario is
       referred to as proxy mode.

   The NATFW NSLP has two basic signaling messages which are sufficient
   to cope with the various possible scenarios likely to be encountered
   before and after widespread deployment of NSIS:

      CREATE message: The basic message for configuring a path outbound
      from a data sender to a data receiver.

      EXTERNAL (EXT) message: Used to locate inbound NATs/firewalls and
      prime them to expect outbound signaling and at NATs to pre-
      allocate a public address.  This is used for data receivers behind
      these devices to enable their reachability.



Stiemerling, et al.     Expires January 10, 2008                [Page 6]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   CREATE and EXT messages are sent by the NSIS initiator (NI) towards
   the NSIS responder (NR).  Both type of messages are acknowledged by a
   subsequent RESPONSE message.  This RESPONSE message is generated by
   the NR if the requested configuration can be established, otherwise
   the NR or any of the NSIS forwarders (NFs) can also generate such a
   message if an error occurs.  NFs and the NR can also generate
   asynchronous messages to notify the NI, the so called NOTIFY
   messages.

   If the data receiver resides in a private addressing realm or
   firewall, and needs to preconfigure the edge-NAT/edge-firewall to
   provide a (publicly) reachable address for use by the data sender, a
   combination of EXTERNAL and CREATE messages is used.

   During the introduction of NSIS, it is likely that one or other of
   the data sender and receiver will not be NSIS aware.  In these cases,
   the NATFW NSLP can utilize NSIS aware middleboxes on the path between
   the data sender and data receiver to provide proxy NATFW NSLP
   services (i.e., the proxy mode operation).  Typically, these boxes
   will be at the boundaries of the realms in which the end hosts are
   located.

   The CREATE and EXT messages create NATFW NSLP and NTLP state in NSIS
   entities.  NTLP state allows signaling messages to travel in the
   forward (outbound) and the reverse (inbound) direction along the path
   between a NAT/firewall NSLP sender and a corresponding receiver.
   This state is managed using a soft-state mechanism, i.e., it expires
   unless it is refreshed from time to time.  The NAT bindings and
   firewall rules being installed during the state setup are bound to
   the particular signaling session.  However, the exact local
   implementation of the NAT bindings and firewall rules are NAT/
   firewall specific.

   This memo is structured as follows.  Section 2 describes the network
   environment for NATFW NSLP signaling.  Section 3 defines the NATFW
   signaling protocol and Section 4 defines the message components and
   the overall messages used in the protocol.  The remaining parts of
   the main body of the document, covers security considerations
   Section 5, IAB considerations on UNilateral Self-Address Fixing
   (UNSAF) [12] in Section 6 and IANA considerations in Section 7.
   Please note that readers familiar with firewalls and NATs and their
   possible location within networks can safely skip Section 2.

1.1.  Terminology and Abbreviations

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [1].



Stiemerling, et al.     Expires January 10, 2008                [Page 7]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   This document uses a number of terms defined in [5] and [4].  The
   following additional terms are used:

   o  Policy rule: A policy rule is "a basic building block of a policy-
      based system.  It is the binding of a set of actions to a set of
      conditions - where the conditions are evaluated to determine
      whether the actions are performed" [16].  In the context of NSIS
      NATFW NSLP, the conditions are the specification of a set of
      packets to which the rule is applied.  The set of actions always
      contains just a single element per rule, and is limited to either
      action "deny" or action "allow".

   o  Reserved policy rule: A policy rule stored at NATs or firewalls
      for activation by a later, different signaling exchange.  This
      type of policy rule is kept in the NATFW NSLP and is not loaded
      into the firewall or NAT engine, i.e., it does not affect the data
      flow handling.

   o  Installed policy rule: A policy rule in operation at NATs or
      firewalls.  This type of rule is kept in the NATFW NSLP and is
      loaded into the firewall or NAT engine, i.e., it is affecting the
      data flow.

   o  Remembered policy rule: A policy rule stored at NATs and firewalls
      for immediate use, as soon as the signaling exchange is
      successfully completed.

   o  Firewall: A packet filtering device that matches packets against a
      set of policy rules and applies the actions.  In the context of
      NSIS NATFW NSLP we refer to this device as a firewall.

   o  Network Address Translator: Network Address Translation is a
      method by which IP addresses are mapped from one IP address realm
      to another, in an attempt to provide transparent routing between
      hosts (see [9]).  Network Address Translators are devices that
      perform this work by modifying packets passing through them.

   o  Middlebox: "A middlebox is defined as any intermediate device
      performing functions other than the normal, standard functions of
      an IP router on the datagram path between a source host and a
      destination host" [10].  In the context of this document, the term
      middlebox refers to firewalls and NATs only.  Other types of
      middlebox are outside of the scope of this document.

   o  Data Receiver (DR): The node in the network that is receiving the
      data packets of a flow.





Stiemerling, et al.     Expires January 10, 2008                [Page 8]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  Data Sender (DS): The node in the network that is sending the data
      packets of a flow.

   o  NATFW NSLP peer or peer: An NSIS NATFW NSLP node with which an
      NSIS adjacency has been created as defined in [2].

   o  NATFW NSLP signaling session or signaling session: A signaling
      session defines an association between the NI, NFs, and the NR
      related to a data flow.  All the NATFW NSLP peers on the path,
      including the NI and the NR, use the same identifier to refer to
      the state stored for the association.  The same NI and NR may have
      more than one signaling session active at any time.  The state for
      NATFW NSLP consists of NSLP state and associated policy rules at a
      middlebox.

   o  Edge-NAT: An edge-NAT is a NAT device with a globally routable IP
      address which is reachable from the public Internet.

   o  Edge-firewall: An edge-firewall is a firewall device that is
      located on the border line of an administrative domain.

   o  Public Network: "A Global or Public Network is an address realm
      with unique network addresses assigned by Internet Assigned
      Numbers Authority (IANA) or an equivalent address registry.  This
      network is also referred as external network during NAT
      discussions" [9].

   o  Private/Local Network: "A private network is an address realm
      independent of external network addresses.  Private network may
      also be referred alternately as Local Network.  Transparent
      routing between hosts in private realm and external realm is
      facilitated by a NAT router" [9].

   o  Public/Global IP address: An IP address located in the public
      network according to Section 2.7 of [9].

   o  Private/Local IP address: An IP address located in the private
      network according to Section 2.8 of [9].

   o  Signaling Destination Address (SDA): An IP address generally taken
      from the public/global IP address range, although, the SDA may in
      certain circumstances be part of the private/local IP address
      range.  This address is used in EXT signaling message exchanges,
      if the data receiver's IP address is unknown.







Stiemerling, et al.     Expires January 10, 2008                [Page 9]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


1.2.  Middleboxes

   The term middlebox covers a range of devices which intercept the flow
   of packets between end hosts and perform actions other than standard
   forwarding expected in an IP router.  As such, middleboxes fall into
   a number of categories with a wide range of functionality, not all of
   which is pertinent to the NATFW NSLP.  Middlebox categories in the
   scope of this memo are firewalls that filter data packets against a
   set of filter rules, and NATs that translate packet addresses from
   one address realm to another address realm.  Other categories of
   middleboxes, such as QoS traffic shapers, are out of scope of this
   memo.

   The term NAT used in this document is a placeholder for a range of
   different NAT flavors.  We consider the following types of NATs:

   o  Traditional NAT (basic NAT and NAPT)

   o  Bi-directional NAT

   o  Twice-NAT

   o  Multihomed NAT

   For definitions and a detailed discussion about the characteristics
   of each NAT type please see [9].

   All types of middleboxes under consideration here, use policy rules
   to make a decision on data packet treatment.  Policy rules consist of
   a flow identifier which selects the packets to which the policy
   applies and an associated action; data packets matching the flow
   identifier are subjected to the policy rule action.  A typical flow
   identifier is the 5-tuple selector which matches the following fields
   of a packet to configured values:

   o  Source and destination IP addresses

   o  Transport protocol number

   o  Transport source and destination port numbers

   Actions for firewalls are usually one or more of:

   o  Allow: forward data packet

   o  Deny: block data packet and discard it





Stiemerling, et al.     Expires January 10, 2008               [Page 10]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  Other actions such as logging, diverting, duplicating, etc

   Actions for NATs include (amongst many others):

   o  Change source IP address and transport port number to a globally
      routeable IP address and associated port number.

   o  Change destination IP address and transport port number to a
      private IP address and associated port number.

   It should be noted that a middlebox may contain two logical
   representations of the policy rule.  The policy rule has a
   representation within the NATFW NSLP, comprising the message routing
   information (MRI) of the NTLP and NSLP information (such as the rule
   action).  The other representation is the implementation of the NATFW
   NSLP policy rule within the NAT and firewall engine of the particular
   device.  Refer to Appendix C for further details.

1.3.  General Scenario for NATFW Traversal

   The purpose of NSIS NATFW signaling is to enable communication
   between endpoints across networks, even in the presence of NAT and
   firewall middleboxes that have not been specially engineered to
   facilitate communication with the application protocols used.  This
   removes the need to create and maintain application layer gateways
   for specific protocols that have been commonly used to provide
   transparency in previous generations of NAT and firewall middleboxes.
   It is assumed that these middleboxes will be statically configured in
   such a way that NSIS NATFW signaling messages themselves are allowed
   to reach the locally installed NATFW NSLP daemon.  NSIS NATFW NSLP
   signaling is used to dynamically install additional policy rules in
   all NATFW middleboxes along the data path that will allow
   transmission of the application data flow(s).  Firewalls are
   configured to forward data packets matching the policy rule provided
   by the NSLP signaling.  NATs are configured to translate data packets
   matching the policy rule provided by the NSLP signaling.  An
   additional capability, that is an exception to the primary goal of
   NSIS NATFW signaling, is that the NATFW nodes can request blocking of
   particular data flows instead of enabling these flows at inbound
   firewalls.

   The basic high-level picture of NSIS usage is that end hosts are
   located behind middleboxes, meaning that there is a middlebox on the
   data path from the end host in a private network and the external
   network (NATFW in Figure 1).  Applications located at these end hosts
   try to establish communication with corresponding applications on
   other such end hosts.  They trigger the NSIS entity at the local host
   to control provisioning for middlebox traversal along the prospective



Stiemerling, et al.     Expires January 10, 2008               [Page 11]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   data path (e.g., via an API call).  The NSIS entity in turn uses NSIS
   NATFW NSLP signaling to establish policy rules along the data path,
   allowing the data to travel from the sender to the receiver
   unobstructed.


   Application          Application Server (0, 1, or more)   Application

   +----+                        +----+                        +----+
   |    +------------------------+    +------------------------+    |
   +-+--+                        +----+                        +-+--+
     |                                                           |
     |         NSIS Entities                      NSIS Entities  |
   +-+--+        +----+                            +-----+     +-+--+
   |    +--------+    +----------------------------+     +-----+    |
   +-+--+        +-+--+                            +--+--+     +-+--+
     |             |               ------             |          |
     |             |           ////      \\\\\        |          |
   +-+--+        +-+--+      |/               |     +-+--+     +-+--+
   |    |        |    |     |   Internet       |    |    |     |    |
   |    +--------+    +-----+                  +----+    +-----+    |
   +----+        +----+      |\               |     +----+     +----+
                               \\\\      /////
   sender    NATFW (1+)            ------          NATFW (1+) receiver

   Note that 1+ refers to one or more NATFW nodes.

         Figure 1: Generic View of NSIS with NATs and/or Firewalls

   For end-to-end NATFW signaling, it is necessary that each firewall
   and each NAT along the path between the data sender and the data
   receiver implements the NSIS NATFW NSLP.  There might be several NATs
   and FWs in various possible combinations on a path between two hosts.
   Section 2 presents a number of likely scenarios with different
   combinations of NATs and firewalls.
















Stiemerling, et al.     Expires January 10, 2008               [Page 12]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


2.  Network Deployment Scenarios using the NATFW NSLP

   This section introduces several scenarios for middlebox placement
   within IP networks.  Middleboxes are typically found at various
   different locations, including at enterprise network borders, within
   enterprise networks, as mobile phone network gateways, etc.  Usually,
   middleboxes are placed more towards the edge of networks than in
   network cores.  Firewalls and NATs may be found at these locations
   either alone, or they may be combined; other categories of
   middleboxes may also be found at such locations, possibly combined
   with the NATs and/or firewalls.  Using combined middleboxes typically
   reduces the number of network elements needed.

   NSIS initiators (NI) send NSIS NATFW NSLP signaling messages via the
   regular data path to the NSIS responder (NR).  On the data path,
   NATFW NSLP signaling messages reach different NSIS nodes that
   implement the NATFW NSLP.  Each NATFW NSLP node processes the
   signaling messages according to Section 3 and, if necessary, installs
   policy rules for subsequent data packets.

   Each of the following sub-sections introduces a different scenario
   for a different set of middleboxes and their ordering within the
   topology.  It is assumed that each middlebox implements the NSIS
   NATFW NSLP signaling protocol.

2.1.  Firewall Traversal

   This section describes a scenario with firewalls only; NATs are not
   involved.  Each end host is behind a firewall.  The firewalls are
   connected via the public Internet.  Figure 2 shows the topology.  The
   part labeled "public" is the Internet connecting both firewalls.


                  +----+    //----\\       +----+
          NI -----| FW |---|        |------| FW |--- NR
                  +----+    \\----//       +----+

                 private     public        private

             FW: Firewall
             NI: NSIS Initiator
             NR: NSIS Responder

                   Figure 2: Firewall Traversal Scenario

   Each firewall on the data path must provide traversal service for
   NATFW NSLP in order to permit the NSIS message to reach the other end
   host.  All firewalls process NSIS signaling and establish appropriate



Stiemerling, et al.     Expires January 10, 2008               [Page 13]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   policy rules, so that the required data packet flow can traverse
   them.

   There are several very different ways to place firewalls in a network
   topology.  To distinguish firewalls located at network borders, such
   as administrative domains, from others located internally, the term
   edge-firewall is used.  A similar distinction can be made for NATs,
   with an edge-NAT fulfilling the equivalent role.

2.2.  NAT with two private Networks

   Figure 3 shows a scenario with NATs at both ends of the network.
   Therefore, each application instance, the NSIS initiator and the NSIS
   responder, are behind NATs.  The outermost NAT, known as the edge-NAT
   (MB2 and MB3), at each side is connected to the public Internet.  The
   NATs are generically labeled as MBX (for middlebox No.  X), since
   those devices certainly implement NAT functionality, but can
   implement firewall functionality as well.

   Only two middleboxes MB are shown in Figure 3 at each side, but in
   general, any number of MBs on each side must be considered.


           +----+     +----+    //----\\    +----+     +----+
      NI --| MB1|-----| MB2|---|        |---| MB3|-----| MB4|--- NR
           +----+     +----+    \\----//    +----+     +----+

                private          public          private


             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder

             Figure 3: NAT with two Private Networks Scenario

   Signaling traffic from NI to NR has to traverse all the middleboxes
   on the path (MB1 to MB4, in this order), and all the middleboxes must
   be configured properly to allow NSIS signaling to traverse them.  The
   NATFW signaling must configure all middleboxes and consider any
   address translation that will result from this configuration in
   further signaling.  The sender (NI) has to know the IP address of the
   receiver (NR) in advance, otherwise it will not be possible to send
   any NSIS signaling messages towards the responder.  Note that this IP
   address is not the private IP address of the responder but the NAT's
   public IP address (here MB3's IP address).  Instead a NAT binding
   (including a public IP address) has to be previously installed on the
   NAT MB3.  This NAT binding subsequently allows packets reaching the



Stiemerling, et al.     Expires January 10, 2008               [Page 14]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   NAT to be forwarded to the receiver within the private address realm.
   The receiver might have a number of ways to learn its public IP
   address and port number (including the NATFW NSLP) and might need to
   signal this information to the sender using the application level
   signaling protocol.

2.3.  NAT with Private Network on Sender Side

   This scenario shows an application instance at the sending node that
   is behind one or more NATs (shown as generic MB, see discussion in
   Section 2.2).  The receiver is located in the public Internet.


             +----+     +----+    //----\\
        NI --| MB |-----| MB |---|        |--- NR
             +----+     +----+    \\----//

                  private          public

             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder

        Figure 4: NAT with Private Network on Sender Side Scenario

   The traffic from NI to NR has to traverse middleboxes only on the
   sender's side.  The receiver has a public IP address.  The NI sends
   its signaling message directly to the address of the NSIS responder.
   Middleboxes along the path intercept the signaling messages and
   configure the policy rules accordingly.

   The data sender does not necessarily know whether the receiver is
   behind a NAT or not, hence, it is the receiving side that has to
   detect whether itself is behind a NAT or not.

2.4.  NAT with Private Network on Receiver Side Scenario

   The application instance receiving data is behind one or more NATs
   shown as MB (see discussion in Section 2.2).












Stiemerling, et al.     Expires January 10, 2008               [Page 15]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


               //----\\    +----+     +----+
        NI ---|        |---| MB |-----| MB |--- NR
               \\----//    +----+     +----+

                public          private

             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder

          Figure 5: NAT with Private Network on Receiver Scenario

   Initially, the NSIS responder must determine its publicly reachable
   IP address at the external middlebox and notify the NSIS initiator
   about this address.  One possibility is that an application level
   protocol is used, meaning that the public IP address is signaled via
   this protocol to the NI.  Afterwards the NI can start its signaling
   towards the NR and therefore establish the path via the middleboxes
   in the receiver side private network.

   This scenario describes the use case for the EXTERNAL message of the
   NATFW NSLP.

2.5.  Both End Hosts behind twice-NATs

   This is a special case, where the main problem arises from the need
   to detect that both end hosts are logically within the same address
   space, but are also in two partitions of the address realm on either
   side of a twice-NAT (see [9] for a discussion of twice-NAT
   functionality).

   Sender and receiver are both within a single private address realm
   but the two partitions potentially have overlapping IP address
   ranges.  Figure 6 shows the arrangement of NATs.

















Stiemerling, et al.     Expires January 10, 2008               [Page 16]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


                                   public

             +----+     +----+    //----\\
        NI --| MB |--+--| MB |---|        |
             +----+  |  +----+    \\----//
                     |
                     |  +----+
                     +--| MB |------------ NR
                        +----+

                   private

             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder

     Figure 6: NAT to Public, Sender and Receiver on either side of a
                            twice-NAT Scenario

   The middleboxes shown in Figure 6 are twice-NATs, i.e., they map IP
   addresses and port numbers on both sides, meaning the mapping of
   source and destination address at the private and public interfaces.

   This scenario requires the assistance of application level entities,
   such as a DNS server.  The application level entities must handle
   requests that are based on symbolic names, and configure the
   middleboxes so that data packets are correctly forwarded from NI to
   NR.  The configuration of those middleboxes may require other
   middlebox communication protocols, such as MIDCOM [7].  NSIS
   signaling is not required in the twice-NAT only case, since
   middleboxes of the twice-NAT type are normally configured by other
   means.  Nevertheless, NSIS signaling might be useful when there are
   also firewalls on the path.  In this case NSIS will not configure any
   policy rule at twice-NATs, but will configure policy rules at the
   firewalls on the path.  The NSIS signaling protocol must be at least
   robust enough to survive this scenario.  This requires that twice-
   NATs must implement the NATFW NSLP also and participate in NATFW
   signaling sessions but they do not change the configuration of the
   NAT, i.e., they only read the address mapping information out of the
   NAT and translate the Message Routing Information (MRI, [2]) within
   the NSLP and NTLP accordingly.  For more information see Appendix C.4

2.6.  Both End Hosts Behind Same NAT

   When NSIS initiator and NSIS responder are behind the same NAT (thus
   being in the same address realm, see Figure 7), they are most likely
   not aware of this fact.  As in Section 2.4 the NSIS responder must
   determine its public IP address in advance and transfer it to the



Stiemerling, et al.     Expires January 10, 2008               [Page 17]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   NSIS initiator.  Afterwards, the NSIS initiator can start sending the
   signaling messages to the responder's public IP address.  During this
   process, a public IP address will be allocated for the NSIS initiator
   at the same middlebox as for the responder.  Now, the NSIS signaling
   and the subsequent data packets will traverse the NAT twice: from
   initiator to public IP address of responder (first time) and from
   public IP address of responder to responder (second time).


               NI              public
                \  +----+     //----\\
                 +-| MB |----|        |
                /  +----+     \\----//
               NR
                   private


             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder

            Figure 7: NAT to Public, Both Hosts Behind Same NAT

2.7.  Multihomed Network with NAT

   The previous sub-sections sketched network topologies where several
   NATs and/or firewalls are ordered sequentially on the path.  This
   section describes a multihomed scenario with two NATs placed on
   alternative paths to the public network.




             +----+    //---\\
   NI -------| MB |---|       |
      \      +----+    \\-+-//
       \                  |
        \                 +----- NR
         \                |
          \  +----+    //-+-\\
           --| MB |---|       |
             +----+    \\---//

        private          public

             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder



Stiemerling, et al.     Expires January 10, 2008               [Page 18]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


                Figure 8: Multihomed Network with Two NATs

   Depending on the destination, either one or the other middlebox is
   used for the data flow.  Which middlebox is used, depends on local
   policy or routing decisions.  NATFW NSLP must be able to handle this
   situation properly, see Section 3.7.2 for an extended discussion of
   this topic with respect to NATs.

2.8.  Multihomed Network with Firewall

   This section describes a multihomed scenario with two firewalls
   placed on alternative paths to the public network (Figure 9).  The
   routing in the private and public network decides which firewall is
   being taken for data flows.  Depending on the data flow's direction,
   either outbound or inbound, a different firewall could be traversed.
   This is a challenge for the EXT message of the NATFW NSLP where the
   NSIS responder is located behind these firewalls within the private
   network.  The EXT message is used to block a particular data flow on
   an inbound firewall.  NSIS must route the EXT message inbound from NR
   to NI probably without knowing which path the data traffic will take
   from NI to NR (see also Appendix B).


             +----+
   NR -------| MB |\
       \     +----+ \  //---\\
        \            -|       |-- NI
         \             \\---//
          \  +----+       |
           --| MB |-------+
             +----+
             private

        private          public

             MB: Middlebox
             NI: NSIS Initiator
             NR: NSIS Responder

              Figure 9: Multihomed Network with two Firewalls











Stiemerling, et al.     Expires January 10, 2008               [Page 19]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


3.  Protocol Description

   This section defines messages, objects, and protocol semantics for
   the NATFW NSLP.

3.1.  Policy Rules

   Policy rules, bound to a NATFW NSLP signaling session, are the
   building blocks of middlebox devices considered in the NATFW NSLP.
   For firewalls the policy rule usually consists of a 5-tuple, source/
   destination addresses, transport protocol, and source/destination
   port numbers, plus an action, such as allow or deny.  For NATs the
   policy rule consists of the action 'translate this address' and
   further mapping information, that might be, in the simplest case,
   internal IP address and external IP address.

   The NATFW NSLP carries, in conjunction with the NTLP's Message
   Routing Information (MRI), the policy rules to be installed at NATFW
   peers.  This policy rule is an abstraction with respect to the real
   policy rule to be installed at the respective firewall or NAT.  It
   conveys the initiator's request and must be mapped to the possible
   configuration on the particular used NAT and/or firewall in use.  For
   pure firewalls one or more filter rules must be created and for pure
   NATs one or more NAT bindings must be created.  In mixed firewall and
   NAT boxes, the policy rule must be mapped to filter rules and
   bindings observing the ordering of the firewall and NAT engine.
   Depending on the ordering, NAT before firewall or vice versa, the
   firewall rules must carry public or private IP addresses.  However,
   the exact mapping depends on the implementation of the firewall or
   NAT which is different for each vendor.

   The policy rule at the NATFW NSLP level comprises the message routing
   information (MRI) part, carried in the NTLP, and the information
   available in the NATFW NSLP.  The information provided by the NSLP is
   stored in the 'extend flow information' (NATFW_EFI) and 'data
   terminal information' (NATFW_DTINFO) objects, and the message type.
   Additional information, such as the external IP address and port
   number, stored in the NAT or firewall, will be used as well.  The MRI
   carries the filter part of the NAT/firewall-level policy rule that is
   to be installed.

   The NATFW NSLP specifies two actions for the policy rules: deny and
   allow.  A policy rule with action set to deny will result in all
   packets matching this rule to be dropped.  A policy rule with action
   set to allow will result in all packets matching this rule to be
   forwarded.





Stiemerling, et al.     Expires January 10, 2008               [Page 20]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


3.2.  Basic Protocol Overview

   The NSIS NATFW NSLP is carried over the General Internet Signaling
   Transport (GIST, the implementation of the NTLP) defined in [2].
   NATFW NSLP messages are initiated by the NSIS initiator (NI), handled
   by NSIS forwarders (NF) and received by the NSIS responder (NR).  It
   is required that at least NI and NR implement this NSLP, intermediate
   NFs only implement this NSLP when they provide relevant middlebox
   functions.  NSIS forwarders that do not have any NATFW NSLP functions
   just forward these packets as they have no interest in them.

   A Data Sender (DS), intending to send data to a Data Receiver (DR)
   has to start NATFW NSLP signaling.  This causes the NI associated
   with the data sender (DS) to launch NSLP signaling towards the
   address of data receiver (DR) (see Figure 10).  Although it is
   expected that the DS and the NATFW NSLP NI will usually reside on the
   same host, this specification does not rule out scenarios where the
   DS and NI reside on different hosts, the so-called proxy mode (see
   Section 3.7.6.)


             +-------+    +-------+    +-------+    +-------+
             | DS/NI |<~~~| MB1/  |<~~~| MB2/  |<~~~| DR/NR |
             |       |--->| NF1   |--->| NF2   |--->|       |
             +-------+    +-------+    +-------+    +-------+

                 ========================================>
                    Data Traffic Direction (outbound)


                  --->  : NATFW NSLP request signaling
                  ~~~>  : NATFW NSLP response signaling
                  DS/NI : Data sender and NSIS initiator
                  DR/NR : Data receiver and NSIS responder
                  MB1   : Middlebox 1 and NSIS forwarder 1
                  MB2   : Middlebox 2 and NSIS forwarder 2

                     Figure 10: General NSIS signaling

   The following list shows the normal sequence of NSLP events without
   detailing the interaction with the NTLP and the interactions on the
   the NTLP level.

   o  NSIS initiators generate NATFW NSLP CREATE/EXT messages and send
      these towards the NSIS responder.  This CREATE/EXT message is the
      initial message which creates a new NATFW NSLP signaling session.
      The NI and the NR will most likely already share an application
      session before they start the NATFW NSLP signaling session.  Note



Stiemerling, et al.     Expires January 10, 2008               [Page 21]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


      the difference between both sessions.

   o  NSLP CREATE/EXT messages are processed each time a NF with NATFW
      NSLP support is traversed.  Each NF that is intercepting a CREATE/
      EXT message and is accepting it for further treatment is joining
      the particular NATFW NSLP signaling session.  These nodes process
      the message, check local policies for authorization and
      authentication, possibly create policy rules, and forward the
      signaling message to the next NSIS node.  The request message is
      forwarded until it reaches the NSIS responder.

   o  NSIS responders will check received messages and process them if
      applicable.  NSIS responders generate RESPONSE messages and send
      them hop-by-hop back to the NI via the same chain of NFs
      (traversal of the same NF chain is guaranteed through the
      established reverse message routing state in the NTLP).  The NR is
      also joining the NATFW NSLP signaling session if the CREATE/EXT
      message is accepted.

   o  The RESPONSE message is processed at each NF that has been
      included in the prior NATFW NSLP signaling session setup.

   o  If the NI has received a successful RESPONSE message and if the
      signaling NATFW NSLP session started with a CREATE message, the
      data sender can start sending its data flow to the data receiver.
      If the Ni has received a successful RESPONSE message and if the
      signaling NATFW NSLP session started with a EXT message, the data
      receiver is ready to receive further CREATE messages.

   Because NATFW NSLP signaling follows the data path from DS to DR,
   this immediately enables communication between both hosts for
   scenarios with only firewalls on the data path or NATs on the sender
   side.  For scenarios with NATs on the receiver side certain problems
   arise, as described in Section 2.4.

   When the NR and the NI are located in different address realms and
   the NR is located behind a NAT, the NI cannot signal to the NR
   address directly.  The DR/NR are not reachable from the NIs using the
   private address of the NR and thus NATFW signaling messages cannot be
   sent to the NR/DR's address.  Therefore, the NR must first obtain a
   NAT binding that provides an address that is reachable for the NI.
   Once the NR has acquired a public IP address, it forwards this
   information to the DS via a separate protocol.  This application
   layer signaling, which is out of scope of the NATFW NSLP, may involve
   third parties that assist in exchanging these messages.

   The same holds partially true for NRs located behind firewalls that
   block all traffic by default.  In this case, NR must tell its inbound



Stiemerling, et al.     Expires January 10, 2008               [Page 22]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   firewalls of inbound NATFW NSLP signaling and corresponding data
   traffic.  Once the NR has informed the inbound firewalls, it can
   start its application level signaling to initiate communication with
   the NI.  This application layer signaling, which is out of scope of
   the NATFW NSLP, may involve third parties that assist in exchanging
   these messages.  This mechanism can be used by machines hosting
   services behind firewalls as well.  In this case, the NR informs the
   inbound firewalls as described, but does not need to communicate this
   to the NIs.

   NATFW NSLP signaling supports this scenario by using the EXT message

   1.  The DR acquires a public address by signaling on the reverse path
       (DR towards DS) and thus making itself available to other hosts.
       This process of acquiring public addresses is called reservation.
       During this process the DR reserves publicly reachable addresses
       and ports suitable for further usage in application level
       signaling and the publicly reachable address for further NATFW
       NSLP signaling.  However, the data traffic will not be allowed to
       use this address/port initially (see next point).  In the process
       of reservation the DR becomes the NI for the messages necessary
       to obtain the publicly reachable IP address, i.e., the NI for
       this specific NATFW NSLP signaling session.

   2.  Now on the side of DS, the NI creates a new NATFW NSLP signaling
       session and signals directly to the public IP address of DR.
       This public IP address is used as NR's address, as the NI would
       do if there is no NAT in between, and creates policy rules at
       middleboxes.  Note, that the reservation will only allow
       forwarding of signaling messages, but not data flow packets.
       Policy rules allowing forwarding of data flow packets set up by
       the prior EXT message signaling will be activated when the
       signaling from NI towards NR is confirmed with a positive
       RESPONSE message.  The EXTERNAL (EXT) message is described
       inSection 3.7.2.
















Stiemerling, et al.     Expires January 10, 2008               [Page 23]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


             +-------+    +-------+    +-------+    +-------+
             | DS/NI |<~~~| MB1/  |<~~~| NR    |    |   DR  |
             |       |--->| NF1   |--->|       |    |       |
             +-------+    +-------+    +-------+    +-------+

                 ========================================>
                    Data Traffic Direction (outbound)


                  --->  : NATFW NSLP request signaling
                  ~~~>  : NATFW NSLP response signaling
                  DS/NI : Data sender and NSIS initiator
                  DR/NR : Data receiver and NSIS responder
                  MB1   : Middlebox 1 and NSIS forwarder 1
                  MB2   : Middlebox 2 and NSIS forwarder 2

                  Figure 11: A NSIS proxy mode signaling

   The above usage assumes that both ends of a communication support
   NSIS, but fails when NSIS is only deployed at one end of the path.
   In this case only one of the receiving or sending side is NSIS aware
   and not both at the same time.  NATFW NSLP supports this scenario
   (i.e., the DR does not support NSIS) by using a proxy mode, as
   described in Section 3.7.6; the proxy mode operation also supports
   scenarios with a data sender that does not support NSIS, i.e. the
   data receiver must act to enable data flows towards itself.

   The basic functionality of the NATFW NSLP provides for opening
   firewall pin holes and creating NAT bindings to enable data flows to
   traverse these devices.  Firewalls are normally expected to work on a
   'deny-all' policy, meaning that traffic not explicitly matching any
   firewall filter rule will be blocked.  Similarly, the normal behavior
   of NATs is to block all traffic that does not match any already
   configured/installed binding or NATFW NSLP session.  However, some
   scenarios require support of firewalls having 'allow-all' policies,
   allowing data traffic to traverse the firewall unless it is blocked
   explicitly.  Data receivers can utilize NATFW NSLP's EXT message with
   action set to 'deny' to install policy rules at inbound firewalls to
   block unwanted traffic.

   The protocol works on a soft-state basis, meaning that whatever state
   is installed or reserved on a middlebox will expire, and thus be de-
   installed or forgotten after a certain period of time.  To prevent
   premature removal of state that is needed for ongoing communication,
   the NATFW NI involved will have to specifically request a NATFW NSLP
   signaling session extension.  An explicit NATFW NSLP state deletion
   capability is also provided by the protocol.




Stiemerling, et al.     Expires January 10, 2008               [Page 24]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   If the actions requested by a NATFW NSLP message cannot be carried
   out, NFs and the NR must return a failure, such that appropriate
   actions can be taken.  They can do this either during a the request
   message handling (synchronously) by sending an error RESPONSE
   message, or at any time (asynchronously) by sending a notification
   message.

   The next sections define the NATFW NSLP message types and formats,
   protocol operations, and policy rule operations.

3.2.1.  Message Types

   The protocol uses four messages types:

   o  CREATE: a request message used for creating, changing, refreshing,
      and deleting NATFW NSLP signaling sessions, i.e., open the data
      path from DS to DR.

   o  EXTERNAL (EXT): a request message used for reserving, changing,
      refreshing, and deleting EXT NATFW NSLP signaling sessions.  EXT
      messages are forwarded to the edge-NAT or edge-firewall and allow
      inbound CREATE messages to be forwarded to the NR.  Additionally,
      EXT messages reserve an external address and, if applicable, port
      number at an edge-NAT.

   o  NOTIFY: an asynchronous message used by NATFW peers to alert
      inbound NATFW peers about specific events (especially failures).

   o  RESPONSE: used as a response to CREATE and EXT request messages.

3.2.2.  Classification of RESPONSE Messages

   RESPONSE messages will be generated synchronously to CREATE and EXT
   messages by NSIS Forwarders and Responders to report success or
   failure of operations or some information relating to the NATFW NSLP
   signaling session or a node.  RESPONSE messages MUST NOT be generated
   for any other message, such as NOTIFY and RESPONSE.

   All RESPONSE messages MUST carry a NATFW_INFO object which contains a
   severity class code and a response code (see Section 4.2.4).  This
   section defines terms for groups of RESPONSE messages depending on
   the severity class.

   o  Successful RESPONSE: Messages carrying NATFW_INFO with severity
      class 'Success' (0x2).

   o  Informational RESPONSE: Messages carrying NATFW_INFO with severity
      class 'Informational' (0x1) (only used with NOTIFY messages).



Stiemerling, et al.     Expires January 10, 2008               [Page 25]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  Error RESPONSE: Messages carrying NATFW_INFO with severity class
      other than 'Success' or 'Informational'.

3.2.3.  NATFW NSLP Signaling Sessions

   A NATFW NSLP signaling session defines an association between the NI,
   NFs, and the NR related to a data flow.  This association is created
   when the initial CREATE or EXT message is successfully received at
   the NFs or the NR.  There is signaling NATFW NSLP session state
   stored at the NTLP layer and at the NATFW NSLP level.  The NATFW NSLP
   signaling session state for the NATFW NSLP comprises NSLP state and
   the associated policy rules at a middlebox.

   The NATFW NSLP signaling session is identified by the session ID
   (plus other information at the NTLP level).  The session ID is
   generated by the NI before the initial CREATE or EXT message is sent.
   The value of the session ID MUST generated in a random way, i.e., the
   output MUST NOT be easily guessable by third parties.  The session ID
   is not stored in any NATFW NSLP message but passed on to the NTLP.

   A NATFW NSLP signaling session can conceptually be in different
   states, implementations may use other or even more states.  The
   signaling session can have these states at a node:

   o  Pending: The NATFW NSLP signaling session has been created and the
      node is waiting for a RESPONSE message to the CREATE or EXT
      message.  A NATFW NSLP signaling session in state 'Pending' MUST
      be marked as 'Dead' if no corresponding RESPONSE message has been
      received within the time of the locally granted NATFW NSLP
      signaling session lifetime of the forwarded CREATE or EXT message
      (as described in Section 3.4).

   o  Established: The NATFW NSLP signaling session is established, i.e,
      the signaling has been successfully performed and the lifetime of
      NATFW NSLP signaling session is counted from now on.  A NATFW NSLP
      signaling session in state 'Established' MUST be marked as 'Dead'
      if no refresh message has been received within the time of the
      locally granted NATFW NSLP signaling session lifetime of the
      RESPONSE message (as described in Section 3.4).

   o  Dead: Either the NATFW NSLP signaling session is timed out or the
      node has received an error RESPONSE message for the NATFW NSLP
      signaling session and the NATFW NSLP signaling session can be
      deleted.

   o  Transit: The node has received an asynchronous message, i.e., a
      NOTIFY, and can delete the NATFW NSLP signaling session if needed.
      When a node has received a NOTIFY message (for instance,



Stiemerling, et al.     Expires January 10, 2008               [Page 26]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


      indicating a route change) it marks it as 'Transit' and deletes
      this NATFW NSLP signaling session if it is unused for some time
      specific to the local node.  This idle time does not need to be
      fixed, since it can depend on the node local maintenance cycle,
      i.e., the NATFW NSLP signaling session could be deleted if the
      node runs it garbage collection cycle.

3.3.  Basic Message Processing

   All NATFW messages are subject to some basic message processing when
   received at a node, independent of message type.  Initially, the
   syntax of the NSLP message is checked and a RESPONSE message with an
   appropriate error of class 'Protocol error' (0x1) code is generated
   if any problem is detected.  If a message is delivered to the NATFW
   NSLP, this implies that the NTLP layer has been able to correlate it
   with the SID and MRI entries in its database.  There is therefore
   enough information to identify the source of the message and routing
   information to route the message back to the NI through an
   established chain of NTLP messaging associations.  The message is not
   further forwarded if any error in the syntax is detected.  The
   specific response codes stemming from the processing of objects are
   described in the respective object definition section (see
   Section 4).  After passing this check, the NATFW NSLP node performs
   authentication/authorization related checks described in Section 3.6.
   Further processing is executed only if these tests have been
   successfully passed, otherwise the processing stops and an error
   RESPONSE is returned.

   Further message processing stops whenever an error RESPONSE message
   is generated, and the EXT or CREATE message is discarded.

3.4.  Calculation of Signaling Session Lifetime

   NATFW NSLP signaling sessions, and the corresponding policy rules
   which may have been installed, are maintained via a soft-state
   mechanism.  Each signaling session is assigned a signaling session
   lifetime and the signaling session is kept alive as long as the
   lifetime is valid.  After the expiration of the signaling session
   lifetime, signaling sessions and policy rules MUST be removed
   automatically and resources bound to them MUST be freed as well.
   Signaling session lifetime is handled at every NATFW NSLP node.  The
   NSLP forwarders and NSLP responder MUST NOT trigger signaling session
   lifetime extension refresh messages (see Section 3.7.3): this is the
   task of the NSIS initiator.

   The NSIS initiator MUST choose a NATFW NSLP signaling session
   lifetime value (expressed in seconds) before sending any message,
   including the initial message which creates the NATFW NSLP signaling



Stiemerling, et al.     Expires January 10, 2008               [Page 27]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   session, to other NSLP nodes.  The NATFW NSLP signaling session
   lifetime value is calculated based on:

   o  the number of lost refresh messages that NFs should cope with;

   o  the end-to-end delay between the NI and NR;

   o  network vulnerability due to NATFW NSLP signaling session
      hijacking ([8]), NATFW NSLP signaling session hijacking is made
      easier when the NI does not explicitly remove the NATFW NSLP
      signaling session);

   o  the user application's data exchange duration, in terms of time
      and networking needs.  This duration is modeled as M x R, with R
      the message refresh period (in seconds) and M as a multiplier for
      R;

   o  the load on the signalling plane.  Short lifetimes imply more
      frequent signaling messages.

   o  the acceptable time for a NATFW NSLP signaling session to be
      present after it is no longer actually needed.  For example, if
      the existence of the NATFW NSLP signaling session implies a
      monetary cost and teardown cannot be guaranteed, shorter lifetimes
      would be preferable.

   o  the lease time of the NI's IP address.  The chosen NATFW NSLP
      signaling session lifetime must be larger than the lease time,
      otherwise the IP address can be re-assigned to a different node.
      This node may receive unwanted traffic, although it never has
      requested a NAT/firewall configuration, which might be an issue in
      mobile environments.

   The RSVP specification [11] provides an appropriate algorithm for
   calculating the NATFW NSLP signaling session lifetime as well as
   means to avoid refresh message synchronization between NATFW NSLP
   signaling sessions. [11] recommends:

   1.  The refresh message timer to be randomly set to a value in the
       range [0.5R, 1.5R].

   2.  To avoid premature loss of state, lt (with lt being the NATFW
       NSLP signaling session lifetime) must satisfy lt >= (K +
       0.5)*1.5*R, where K is a small integer.  Then in the worst case,
       K-1 successive messages may be lost without state being deleted.
       Currently K = 3 is suggested as the default.  However, it may be
       necessary to set a larger K value for hops with high loss rate.
       Other algorithms could be used to define the relation between the



Stiemerling, et al.     Expires January 10, 2008               [Page 28]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


       NATFW NSLP signaling session lifetime and the refresh message
       period; the algorithm provided is only given as an example.

   This requested NATFW NSLP signaling session lifetime value lt is
   stored in the NATFW_LT object of the NSLP message.

   NSLP forwarders can execute the following behavior with respect to
   the lifetime handling:

   Requested signaling session lifetime acceptable:

      No changes to the NATFW NSLP signaling session lifetime values are
      needed.  The CREATE or EXT message is forwarded.


   Signaling session lifetime can be lowered:

      The NSLP responder MAY also lower the requested NATFW NSLP
      signaling session lifetime to an acceptable value (based on its
      local policies).  If an NF changes the NATFW NSLP signaling
      session lifetime value, it MUST store the new value in the
      NATFW_LT object.  The CREATE or EXT message is forwarded.


   Requested signaling session lifetime is too big:

      The NSLP responder MAY reject the requested NATFW NSLP signaling
      session lifetime value as being too big and MUST generate an error
      RESPONSE message of class 'Signaling session failures' (0x6) with
      response code 'Requested lifetime is too big' (0x02) upon
      rejection.  Lowering the lifetime is preferred instead of
      generating an error message.


   Requested signaling session lifetime is too small:

      The NSLP responder MAY reject the requested NATFW NSLP signaling
      session lifetime value as being to small and MUST generate an
      error RESPONSE message of class 'Signaling session failures' (0x6)
      with response code 'Requested lifetime is too small' (0x10) upon
      rejection.

   NFs MUST NOT increase the NATFW NSLP signaling session lifetime
   value.  Messages can be rejected on the basis of the NATFW NSLP
   signaling session lifetime being too long when a NATFW NSLP signaling
   session is first created and also on refreshes.

   The NSLP responder generates a successful RESPONSE for the received



Stiemerling, et al.     Expires January 10, 2008               [Page 29]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   CREATE or EXT message, sets the NATFW NSLP signaling session lifetime
   value in the NATFW_LT object to the above granted lifetime and sends
   the message back towards NSLP initiator.

   Each NSLP forwarder processes the RESPONSE message, reads and stores
   the granted NATFW NSLP signaling session lifetime value.  The
   forwarders MUST accept the granted NATFW NSLP signaling session
   lifetime, as long as this value is less than or equal to the
   acceptable value.  The acceptable value refers to the value accepted
   by the NSLP forwarder when processing the CREATE or EXT message.  For
   received values greater than the acceptable value, NSLP forwarders
   MUST generate a RESPONSE message of class 'Signaling session
   failures' (0x6) with response code 'Requested lifetime is too big'
   (0x02).  For received values lower than the values acceptable by the
   node local policy, NSLP forwarders MUST generate a RESPONSE message
   of class 'Signaling session failures' (0x6) with response code
   'Requested lifetime is too small' (0x10).  Figure 12 shows the
   procedure with an example, where an initiator requests 60 seconds
   lifetime in the CREATE message and the lifetime is shortened along
   the path by the forwarder to 20 seconds and by the responder to 15
   seconds.  When the NSLP forwarder receives the RESPONSE message with
   a NATFW NSLP signaling session lifetime value of 15 seconds it checks
   whether this value is lower or equal to the acceptable value.


   +-------+ CREATE(lt=60s)  +-------------+ CREATE(lt=20s)  +--------+
   |       |---------------->|     NSLP    |---------------->|        |
   |  NI   |                 |  forwarder  |                 |  NR    |
   |       |<----------------| check 15<20 |<----------------|        |
   +-------+ RESPONSE(lt=15s)+-------------+ RESPONSE(lt=15s)+--------+

      lt  = lifetime

           Figure 12: Signaling Session Lifetime Setting Example

3.5.  Message Sequencing

   NATFW NSLP messages need to carry an identifier so that all nodes
   along the path can distinguish messages sent at different points in
   time.  Messages can be lost along the path or duplicated.  So all
   NATFW NSLP nodes should be able to identify either old messages that
   have been received before (duplicated), or the case that messages
   have been lost before (loss).  For message replay protection it is
   necessary to keep information about messages that have already been
   received and requires every NATFW NSLP message to carry a message
   sequence number (MSN), see also Section 4.2.6.

   The MSN MUST be set by the NI and MUST NOT be set or modified by any



Stiemerling, et al.     Expires January 10, 2008               [Page 30]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   other node.  The initial value for the MSN MUST be generated randomly
   and MUST be unique only within the NATFW NSLP signaling session for
   which it is used.  The NI MUST increment the MSN by one for every
   message sent.  Once the MSN has reached the maximum value, the next
   value it takes is zero.  All NATFW NSLP nodes MUST use the algorithm
   defined in [3] to detect MSN wrap-arounds.

   NSIS forwarders and the responder store the MSN from the initial
   CREATE or EXT packet which creates the NATFW NSLP signaling session
   as the start value for the NATFW NSLP signaling session.  NFs and NRs
   MUST include the received MSN value in the corresponding RESPONSE
   message that they generate.

   When receiving a CREATE or EXT message, a NATFW NSLP node uses the
   MSN given in the message to determine whether the state being
   requested is different to the state already installed.  The message
   MUST be discarded if the received MSN value is equal to or lower than
   the stored MSN value.  Such a received MSN value can indicate a
   duplicated and delayed message or replayed message.  If the received
   MSN value is greater than the already stored MSN value, the NATFW
   NSLP MUST update its stored state accordingly, if permitted by all
   security checks (see Section 3.6), and stores the updated MSN value
   accordingly.

3.6.  Authentication, Authorization, and Policy Decisions

   NATFW NSLP nodes receiving signaling messages MUST first check
   whether this message is authenticated and authorized to perform the
   requested action.  NATFW NSLP nodes requiring more information than
   provided MUST generate an error RESPONSE of class 'Permanent failure'
   (0x5) with response code 'Authentication failed' (0x01) or with
   response code 'Authorization failed' (0x02).

   The NATFW NSLP is expected to run in various environments, such as
   IP-based telephone systems, enterprise networks, home networks, etc.
   The requirements on authentication and authorization are quite
   different between these use cases.  While a home gateway, or an
   Internet cafe, using NSIS may well be happy with a "NATFW signaling
   coming from inside the network" policy for authorization of
   signaling, enterprise networks are likely to require more strongly
   authenticated/authorized signaling.  This enterprise scenario may
   require the use of an infrastructure and administratively assigned
   identities to operate the NATFW NSLP.

   Once the NI is authenticated and authorized, another step is
   performed.  The requested policy rule for the NATFW NSLP signaling
   session is checked against a set of policy rules, i.e., whether the
   requesting NI is allowed to request the policy rule to be loaded in



Stiemerling, et al.     Expires January 10, 2008               [Page 31]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   the device.  If this fails the NF or NR must send an error RESPONSE
   of class 'Permanent failure' (0x5) and with response code
   'Authorization failed' (0x02).

3.7.  Protocol Operations

   This section defines the protocol operations including, how to create
   NATFW NSLP signaling sessions, maintain them, and how to reserve
   addresses.

3.7.1.  Creating Signaling Sessions

   Allowing two hosts to exchange data even in the presence of
   middleboxes is realized in the NATFW NSLP by use of the CREATE
   message.  The NI (either the data sender or a proxy) generates a
   CREATE message as defined in Section 4.3.1 and hands it to the NTLP.
   The NTLP forwards the whole message on the basis of the message
   routing information (MRI) towards the NR.  Each NSIS forwarder along
   the path that implements NATFW NSLP, processes the NSLP message.
   Forwarding is thus managed NSLP hop-by-hop but may pass transparently
   through NSIS forwarders which do not contain NATFW NSLP functionality
   and non-NSIS aware routers between NSLP hop way points.  When the
   message reaches the NR, the NR can accept the request or reject it.
   The NR generates a response to CREATE and this response is
   transported hop-by-hop towards the NI.  NATFW NSLP forwarders may
   reject requests at any time.  Figure 13 sketches the message flow
   between NI (DS in this example), a NF (e.g., NAT), and NR (DR in this
   example).


       NI      Private Network        NF    Public Internet        NR
       |                              |                            |
       | CREATE                       |                            |
       |----------------------------->|                            |
       |                              |                            |
       |                              |                            |
       |                              | CREATE                     |
       |                              |--------------------------->|
       |                              |                            |
       |                              | RESPONSE                   |
       |    RESPONSE                  |<---------------------------|
       |<-----------------------------|                            |
       |                              |                            |
       |                              |                            |

           Figure 13: CREATE message flow with success RESPONSE

   There are several processing rules for a NATFW peer when generating



Stiemerling, et al.     Expires January 10, 2008               [Page 32]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   and receiving CREATE messages, since this message type is used for
   creating new NATFW NSLP signaling session, updating existing,
   extending the lifetime and deleting NATFW NSLP signaling session.
   The three latter functions operate in the same way for all kinds of
   CREATE message, and are therefore described in separate sections:

   o  Extending the lifetime of NATFW NSLP signaling sessions is
      described in Section 3.7.3.

   o  Deleting NATFW NSLP signaling sessions is described in
      Section 3.7.4.

   o  Updating policy rules is described in Section 3.10.

   For an initial CREATE message creating a new NATFW NSLP signaling
   session, the processing of CREATE messages is different for every
   NATFW node type:

   o  NSLP initiator: An NI only generates CREATE messages and hands
      them over to the NTLP.  The NI should never receive CREATE
      messages and MUST discard it.

   o  NATFW NSLP forwarder: NFs that are unable to forward the CREATE
      message to the next hop MUST generate an error RESPONSE of class
      'Permanent failure' (0x6) with response code 'Did not reach the
      NR' (0x07).  This case may occur if the NTLP layer cannot find an
      NATFW NSLP peer, either another NF or the NR, and returns an error
      via the GIST API.  The NSLP message processing at the NFs depends
      on the middlebox type:

      *  NAT: When the initial CREATE message is received at the public
         side of the NAT, it looks for a reservation made in advance, by
         using a EXT message (see Section 3.7.2).  The matching process
         considers the received MRI information and the stored MRI
         information, as described in Section 3.8.  If no matching
         reservation can be found, i.e. no reservation has been made in
         advance, the NSLP MUST return an error RESPONSE of class
         'Signaling session failure' (0x6) with response code 'No
         reservation found matching the MRI of the CREATE request'
         (0x03) MUST be generated.  If there is a matching reservation,
         the NSLP stores the data sender's address (and if applicable
         port number) as part of the source address of the policy rule
         ('the remembered policy rule') to be loaded and forwards the
         message with the destination address set to the internal
         (private in most cases) address of NR.  When the initial CREATE
         message is received at the private side, the NAT binding is
         allocated, but not activated (see also Appendix C.3).  The MRI
         information is updated to reflect the address, and if



Stiemerling, et al.     Expires January 10, 2008               [Page 33]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


         applicable port, translation.  The NSLP message is forwarded
         towards the NR with source address set to the NAT's external
         address from the newly remembered binding.

      *  Firewall: When the initial CREATE message is received, the NSLP
         just remembers the requested policy rule, but does not install
         any policy rule.  Afterwards, the message is forwarded towards
         the NR.

      *  Combined NAT and firewall: Processing at combined firewall and
         NAT middleboxes is the same as in the NAT case.  No policy
         rules are installed.  Implementations MUST take into account
         the order of packet processing in the firewall and NAT
         functions within the device.  This will be referred to as
         'order of functions' and is generally different depending on
         whether the packet arrives at the external or internal side of
         the middlebox.

   o  NSLP receiver: NRs receiving initial CREATE messages MUST reply
      with a success RESPONSE of class 'Success' (0x2) with response
      code set to 'All successfully processed' (0x01), if they accept
      the CREATE message.  Otherwise they MUST generate a RESPONSE
      message with a suitable response code.  RESPONSE messages are sent
      back NSLP hop-by-hop towards the NI, irrespective of the response
      codes, either success or error.

   Remembered policy rules at middleboxes MUST be only installed upon
   receiving a corresponding successful RESPONSE message with the same
   SID and MSN as the CREATE message that caused them to be remembered.
   This is a countermeasure to several problems, for example, wastage of
   resources due to loading policy rules at intermediate NFs when the
   CREATE message does not reach the final NR for some reason.

   Processing of a RESPONSE message is different for every NSIS node
   type:

   o  NSLP initiator: After receiving a successful RESPONSE, the data
      path is configured and the DS can start sending its data to the
      DR.  After receiving an error RESPONSE message, the NI MAY try to
      generate the CREATE message again or give up and report the
      failure to the application, depending on the error condition.

   o  NSLP forwarder: NFs install the remembered policy rules, if a
      successful RESPONSE message with matching SID and MSN is received.
      If an ERROR RESPONSE message with matching SID and MSN is
      received, the NATFW NSLP session is marked as dead, no policy rule
      is installed and the remembered rule is discarded.




Stiemerling, et al.     Expires January 10, 2008               [Page 34]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  NSIS responder: The NR should never receive RESPONSE messages and
      MUST silently drop any such messages received.

3.7.2.  Reserving External Addresses

   NSIS signaling is intended to travel end-to-end, even in the presence
   of NATs and firewalls on-path.  This works well in cases where the
   data sender is itself behind a NAT or a firewall as described in
   Section 3.7.1.  For scenarios where the data receiver is located
   behind a NAT or a firewall and it needs to receive data flows from
   outside its own network (usually referred to as inbound flows, see
   Figure 5) the problem is more troublesome.

   NSIS signaling, as well as subsequent data flows, are directed to a
   particular destination IP address that must be known in advance and
   reachable.  Data receivers must tell the local NSIS infrastructure
   (i.e., the inbound firewalls/NATs) about incoming NATFW NSLP
   signaling and data flows before they can receive these flows.  It is
   necessary to differentiate between data receivers behind NATs and
   behind firewalls for understanding the further NATFW procedures.
   Data receivers that are only behind firewalls already have a public
   IP address and they need only to be reachable for NATFW signaling.
   Unlike data receivers behind just firewalls, data receivers behind
   NATs do not have public IP addresses; consequently they are not
   reachable for NATFW signaling by entities outside their addressing
   realm.

   The preceding discussion addresses the situation where a DR node that
   wants to be reachable is unreachable because the NAT lacks a suitable
   rule with the 'allow' action which would forward inbound data.
   However, in certain scenarios, a node situated behind inbound
   firewalls that do not block inbound data traffic (firewalls with
   "default to allow") unless requested might wish to prevent traffic
   being sent to it from specified addresses.  In this case, NSIS NATFW
   signaling can be used to achieve this by installing a policy rule
   with its action set to 'deny' using the same mechanisms as for
   'allow' rules.

   The required result is obtained by sending a EXTERNAL (EXT) message
   in the inbound direction of the intended data flow.  When using this
   functionality the NSIS initiator for the 'Reserve External Address'
   signaling is typically the node that will become the DR for the
   eventual data flow.  To distinguish this initiator from the usual
   case where the NI is associated with the DS, the NI is denoted by NI+
   and the NSIS responder is similarly denoted by NR+.






Stiemerling, et al.     Expires January 10, 2008               [Page 35]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


       Public Internet                Private Address
                                           Space

                    Edge
    NI(DS)         NAT/FW                  NAT                   NR(DR)
    NR+                                                          NI+

    |               |                       |                       |
    |               |                       |                       |
    |               |                       |                       |
    |               |    EXT[(DTInfo)]      |    EXT[(DTInfo)]      |
    |               |<----------------------|<----------------------|
    |               |                       |                       |
    |               |RESPONSE[Success/Error]|RESPONSE[Success/Error]|
    |               |---------------------->|---------------------->|
    |               |                       |                       |
    |               |                       |                       |

      ============================================================>
                        Data Traffic Direction

     Figure 14: Reservation message flow for DR behind NAT or firewall

   Figure 14 shows the EXT message flow for enabling inbound NATFW NSLP
   signaling messages.  In this case the roles of the different NSIS
   entities are:

   o  The data receiver (DR) for the anticipated data traffic is the
      NSIS initiator (NI+) for the EXTERNAL (EXT) message, but becomes
      the NSIS responder (NR) for following CREATE messages.

   o  The actual data sender (DS) will be the NSIS initiator (NI) for
      later CREATE messages and may be the NSIS target of the signaling
      (NR+).

   o  It may be necessary to use a signaling destination address (SDA)
      as the actual target of the EXT message (NR+) if the DR is located
      behind a NAT and the address of the DS is unknown.  The SDA is an
      arbitrary address in the outermost address realm on the other side
      of the NAT from the DR.  Typically this will be a suitable public
      IP address when the 'outside' realm is the public Internet.  This
      choice of address causes the EXT message to be routed through the
      NATs towards the outermost realm and would force interception of
      the message by the outermost NAT in the network at the boundary
      between the private address and the public address realm (the
      edge-NAT).  It may also be intercepted by other NATs and firewalls
      on the path to the edge-NAT.




Stiemerling, et al.     Expires January 10, 2008               [Page 36]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   Basically, there are two different signaling scenarios.  Either

   1.  the DR behind the NAT/firewall knows the IP address of the DS in
       advance,

   2.  or the address of DS is not known in advance.

   Case 1 requires the NATFW NSLP to request the path-coupled message
   routing method (PC-MRM) from the NTLP.  The EXT message MUST be sent
   with PC-MRM (see Section 5.8.1 in [2]) with the direction set to
   'upstream' (inbound).  The handling of case 2 depends on the
   situation of DR: If DR is solely located behind a firewall, the EXT
   message MUST be sent with the PC-MRM, direction 'upstream' (inbound),
   and data flow source IP address set to wildcard.  If DR is located
   behind a NAT, the EXT message MUST be sent with the loose-end message
   routing method (LE-MRM, see Section 5.8.2 in [2]), the destination-
   address set to the signaling destination address (SDA, see also
   Appendix A).  For scenarios with DR being behind a firewall, special
   conditions apply (applicability statement, Appendix B).  The data
   receiver is challenged to determine whether it is solely located
   behind firewalls or NATs, for choosing the right message routing
   method.  This decision can depend on a local configuration parameter,
   possibly given through DHCP, or it could be discovered through other
   non-NSLP related testing of the network configuration.

   For case 2 with NAT, the NI+ (which could be on the data receiver DR
   or on any other host within the private network) sends the EXT
   message targeted to the signaling destination address.  The message
   routing for the EXT message is in the reverse direction to the normal
   message routing used for path-coupled signaling where the signaling
   is sent outbound (as opposed to inbound in this case).  When
   establishing NAT bindings (and an NATFW NSLP signaling session) the
   signaling direction does not matter since the data path is modified
   through route pinning due to the external IP address at the NAT.
   Subsequent NSIS messages (and also data traffic) will travel through
   the same NAT boxes.  However, this is only valid for the NAT boxes,
   but not for any intermediate firewall.  That is the reason for having
   a separate CREATE message enabling the reservations made with EXT at
   the NATs and either enabling prior reservations or creating new
   pinholes at the firewalls which are encountered on the outbound path
   depending on whether the inbound and outbound routes coincide.

   The EXT signaling message creates an NSIS NATFW signaling session at
   any intermediate NSIS NATFW peer(s) encountered, independent of the
   message routing method used.  Furthermore, it has to be ensured that
   the edge-NAT or edge-firewall device is discovered as part of this
   process.  The end host cannot be assumed to know this device -
   instead the NAT or firewall box itself is assumed to know that it is



Stiemerling, et al.     Expires January 10, 2008               [Page 37]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   located at the outer perimeter of the network.  Forwarding of the EXT
   message beyond this entity is not necessary, and MUST be prohibited
   as it may provide information on the capabilities of internal hosts.
   It should be noted, that it is the outermost NAT or firewall that is
   the edge-device that must be found during this discovery process.
   For instance, when there are a NAT and afterwards a firewall on the
   outbound path at the network border, the firewall is the edge-
   firewall.  All messages must be forwarded to the topology-wise
   outermost edge-device, to ensure that this devices knows about the
   NATFW NSLP signaling sessions for incoming CREATE messages.  However,
   the NAT is still the edge-NAT because it has a public globally
   routable IP address on its public side: this is not affected by any
   firewall between the edge-NAT and the public network.


   Possible edge arrangements are:

          Public Net   -----------------  Private net  --------------

        | Public Net|--|Edge-FW|--|FW|...|FW|--|DR|

        | Public Net|--|Edge-FW|--|Edge-NAT|...|NAT or FW|--|DR|

        | Public Net|--|Edge-NAT|--|NAT or FW|...|NAT or FW|--|DR|

   The edge-NAT or edge-firewall device closest to the public realm
   responds to the EXT message with a successful RESPONSE message.  An
   edge-NAT includes an NATFW_EXT_IP object (see Section 4.2.2),
   carrying the public reachable IP address, and if applicable port
   number.

   There are several processing rules for a NATFW peer when generating
   and receiving EXT messages, since this message type is used for
   creating new reserve NATFW NSLP signaling sessions, updating
   existing, extending the lifetime and deleting NATFW NSLP signaling
   session.  The three latter functions operate in the same way for all
   kinds of CREATE and EXT messages, and are therefore described in
   separate sections:

   o  Extending the lifetime of NATFW NSLP signaling sessions is
      described in Section 3.7.3.

   o  Deleting NATFW NSLP signaling sessions is described in
      Section 3.7.4.

   o  Updating policy rules is described in Section 3.10.

   The NI+ MUST include a NATFW_DTINFO object in the EXT message when



Stiemerling, et al.     Expires January 10, 2008               [Page 38]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   using the LE-MRM.  The LE-MRM does not include enough information for
   some types of NATs (basically, those NATs which also translate port
   numbers) to perform the address translation.  This information is
   provided in the NATFW_DTINFO (see Section 4.2.7).  This information
   MUST include at least the 'dst port number' and 'protocol' fields, in
   the NATFW_DTINFO object as these may be required by en-route NATs,
   depending on the type of the NAT.  All other fields MAY be set by the
   NI+ to restrict the set of possible NIs.  An edge-NAT will use the
   information provided in the NATFW_DTINFO object to allow only NATFW
   CREATE message with the MRI matching ('src IPv4/v6 address', 'src
   port number', 'protocol') to be forwarded.  A NAT requiring
   information carried in the NATFW_DTINFO can generate a number of
   error RESPONSE messages of class 'Signaling session failures' (0x6):

   o  'Requested policy rule denied due to policy conflict' (0x04)

   o  'NATFW_DTINFO object is required' (0x07)

   o  'Requested value in sub_ports field in NATFW_EFI not permitted'
      (0x08)

   o  'Requested IP protocol not supported' (0x09)

   o  'Plain IP policy rules not permitted -- need transport layer
      information' (0x0A)

   o  'source IP address range is too large' (0x0C)

   o  'destination IP address range is too large' (0x0D)

   o  'source L4-port range is too large' (0x0E)

   o  'destination L4-port range is too large' (0x0F)

   Processing of EXT messages is specific to the NSIS node type:

   o  NSLP initiator: NI+ only generate EXT messages.  When the data
      sender's address information is known in advance the NI+ can
      include a NATFW_DTINFO object in the EXT message, if not anyway
      required to do so (see above).  When the data sender's IP address
      is not known, the NI+ MUST NOT include a NATFW_DTINFO object.  The
      NI should never receive EXT messages and MUST silently discard it.

   o  NSLP forwarder: The NSLP message processing at NFs depends on the
      middlebox type:

      *  NAT: NATs check whether the message is received at the external
         (public in most cases) address or at the internal (private)



Stiemerling, et al.     Expires January 10, 2008               [Page 39]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


         address.  If received at the external an NF MUST generate an
         error RESPONSE of class 'Protocol error' (0x3) with response
         code 'Received EXT request message on external side' (0x0B).
         If received at the internal (private address) and the NATFW_EFI
         object contains the action 'deny', an error RESPONSE of class
         'Protocol error' (0x3) with response code 'Requested rule
         action not applicable' (0x06) MUST be generated.  If received
         at the internal address, an IP address, and if applicable one
         or more ports, are reserved.  If it is an edge-NAT and there is
         no edge-firewall beyond, the NSLP message is not forwarded any
         further and a successful RESPONSE message is generated
         containing an NATFW_EXT_IP object holding the translated
         address, and if applicable port, information from the binding
         reserved as a result of the EXT message.  The RESPONSE message
         is sent back towards the NI+.  If it is not an edge-NAT, the
         NSLP message is forwarded further using the translated IP
         address as signaling source address in the LE-MRM and
         translated port in the NATFW_DTINFO object in the field 'DR
         port number', i.e., the NATFW_DTINFO object is updated to
         reflect the translated port number.  The edge-NAT or any other
         NAT MUST reject EXT messages not carrying a NATFW_DTINFO object
         or if the address information within this object is invalid or
         is not compliant with local policies (e.g., the information
         provided relates to a range of addresses ('wildcarded') but the
         edge-NAT requires exact information about DS' IP address and
         port) with the above mentioned response codes.

      *  Firewall: Non edge-firewalls remember the requested policy
         rule, keep NATFW NSLP signaling session state, and forward the
         message.  Edge-firewalls stop forwarding the EXT message.  The
         policy rule is immediately loaded if the action in the
         NATFW_EFI object is set to 'deny' and the node is an edge-
         firewall.  The policy rule is remembered, but not activated, if
         the action in the NATFW_EFI object is set to 'allow'.  In both
         cases, a successful RESPONSE message is generated.  If the
         action is 'allow', and the NATFW_DTINFO object is included, and
         the MRM is set to LE-MRM in the request, additionally an
         NATFW_EXT_IP object is included in the RESPONSE message,
         holding the translated address, and if applicable port,
         information.  This information is obtained from the
         NATFW_DTINFO object's 'DR port number' and the source-address
         of the LE-MRM.

      *  Combined NAT and firewall: Processing at combined firewall and
         NAT middleboxes is the same as in the NAT case.






Stiemerling, et al.     Expires January 10, 2008               [Page 40]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  NSLP receiver: This type of message should never be received by
      any NR+ and it MUST generate an error RESPONSE message of class
      'Permanent failure' (0x5) with response code 'No edge-device here'
      (0x06).

   Processing of a RESPONSE message is different for every NSIS node
   type:

   o  NSLP initiator: Upon receiving a successful RESPONSE message, the
      NI+ can rely on the requested configuration for future inbound
      NATFW NSLP signaling sessions.  If the response contains an
      NATFW_EXT_IP object, the NI can use IP address and port pairs
      carried for further application signaling.  After receiving a
      error RESPONSE message, the NI+ MAY try to generate the EXT
      message again or give up and report the failure to the
      application, depending on the error condition.

   o  NSLP forwarder: NFs simply forward this message as long as they
      keep state for the requested reservation, if the RESPONSE message
      contains NATFW_INFO object with class set to 'Success' (0x2).  If
      the RESPONSE message contains NATFW_INFO object with class set not
      to 'Success' (0x2), the NATFW NSLP signaling session is marked as
      dead.

   o  NSIS responder: This type of message should never be received by
      any NR+.  The NF should never receive response messages and MUST
      silently discard it.

   Reservations with action 'allow' made with EXT MUST be enabled by a
   subsequent CREATE message.  A reservation made with EXT (independent
   of selected action) is kept alive as long as the NI+ refreshes the
   particular NATFW NSLP signaling session and it can be reused for
   multiple, different CREATE messages.  An NI+ may decide to teardown a
   reservation immediately after receiving a CREATE message.  This
   implies that a new NATFW NSLP signaling session must be created for
   each new CREATE message.  The CREATE message does not re-use the
   NATFW NSLP signaling session created by REA.

   Without using CREATE Section 3.7.1 or EXT in proxy mode Section 3.7.6
   no data traffic will be forwarded to DR beyond the edge-NAT or edge-
   firewall.  The only function of EXT is to ensure that subsequent
   CREATE messages traveling towards the NR will be forwarded across the
   public-private boundary towards the DR.  Correlation of incoming
   CREATE messages to EXT reservation states is described in
   Section 3.8.






Stiemerling, et al.     Expires January 10, 2008               [Page 41]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


3.7.3.  NATFW NSLP Signaling Session Refresh

   NATFW NSLP signaling sessions are maintained on a soft-state basis.
   After a specified timeout, sessions and corresponding policy rules
   are removed automatically by the middlebox, if they are not
   refreshed.  Soft-state is created by CREATE and EXT and the
   maintenance of this state must be done by these messages.  State
   created by CREATE must be maintained by CREATE, state created by EXT
   must be maintained by EXT.  Refresh messages, are messages carrying
   the same session ID as the initial message and a NATFW_LT lifetime
   object with a lifetime greater than zero.  Messages with the same SID
   but carrying a different MRI are treated as updates of the policy
   rules and are processed as defined in Section 3.10.  Every refresh
   CREATE or EXT message MUST be acknowledged by an appropriate response
   message generated by the NR.  Upon reception by each NSIS forwarder,
   the state for the given session ID is extended by the NATFW NSLP
   signaling session refresh period, a period of time calculated based
   on a proposed refresh message period.  The lifetime extension of a
   NATFW NSLP signaling session is calculated as current local time plus
   proposed lifetime value (NATFW NSLP signaling session refresh
   period).  Section 3.4 defines the process of calculating lifetimes in
   detail.


   NI      Public Internet        NAT    Private address       NR

      |                              |          space             |
      | CREATE[lifetime > 0]         |                            |

      |----------------------------->|                            |
      |                              |                            |
      |                              |                            |
      |                              |  CREATE[lifetime > 0]      |
      |                              |--------------------------->|
      |                              |                            |
      |                              |   RESPONSE[Success/Error]  |
      |   RESPONSE[Success/Error]    |<---------------------------|
      |<-----------------------------|                            |
      |                              |                            |
      |                              |                            |

       Figure 16: Successful Refresh Message Flow, CREATE as example

   Processing of NATFW NSLP signaling session refresh CREATE and EXT
   messages is different for every NSIS node type:

   o  NSLP initiator: The NI/NI+ can generate NATFW NSLP signaling
      session refresh CREATE/EXT messages before the NATFW NSLP



Stiemerling, et al.     Expires January 10, 2008               [Page 42]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


      signaling session times out.  The rate at which the refresh
      CREATE/EXT messages are sent and their relation to the NATFW NSLP
      signaling session state lifetime is discussed further in
      Section 3.4.

   o  NSLP forwarder: Processing of this message is independent of the
      middlebox type and is as described in Section 3.4.

   o  NSLP responder: NRs accepting a NATFW NSLP signaling session
      refresh CREATE/EXT message generate a successful RESPONSE message,
      including the granted lifetime value of Section 3.4 in a NATFW_LT
      object.

3.7.4.  Deleting Signaling Sessions

   NATFW NSLP signaling sessions can be deleted at any time.  NSLP
   initiators can trigger this deletion by using a CREATE or EXT
   messages with a lifetime value set to 0, as shown in Figure 17.
   Whether a CREATE or EXT message type is used, depends on how the
   NATFW NSLP signaling session was created.


      NI      Public Internet        NAT    Private address       NR

      |                              |          space             |
      |    CREATE[lifetime=0]        |                            |
      |----------------------------->|                            |
      |                              |                            |
      |                              | CREATE[lifetime=0]         |
      |                              |--------------------------->|
      |                              |                            |

             Figure 17: Delete message flow, CREATE as example

   NSLP nodes receiving this message delete the NATFW NSLP signaling
   session immediately.  Policy rules associated with this particular
   NATFW NSLP signaling session MUST be also deleted immediately.  This
   message is forwarded until it reaches the final NR.  The CREATE/EXT
   message with a lifetime value of 0, does not generate any response,
   neither positive nor negative, since there is no NSIS state left at
   the nodes along the path.

   NSIS initiators can use CREATE/EXT message with lifetime set to zero
   in an aggregated way, such that a single CREATE or EXT message is
   terminating multiple NATFW NSLP signaling sessions.  NIs can follow
   this procedure if the like to aggregate NATFW NSLP signaling session
   deletion requests: The NI uses the CREATE or EXT message with the
   session ID set to zero and the MRI's source-address set to its used



Stiemerling, et al.     Expires January 10, 2008               [Page 43]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   IP address.  All other fields of the respective NATFW NSLP signaling
   sessions to be terminated are set as well, otherwise these fields are
   completely wildcarded.  The NSLP message is transferred to the NTLP
   requesting 'explicit routing' as described in Sections 5.2.1 and
   7.1.4. in [2].

   The outbound NF receiving such an aggregated CREATE or EXT message
   MUST reject it with an error RESPONSE of class 'Permanent failure'
   (0x5) with response code 'Authentication failed' (0x01) if the
   authentication fails and with an error RESPONSE of class 'Permanent
   failure' (0x5) with response code 'Authorization failed' (0x02) if
   the authorization fails.  Per NATFW NSLP signaling session proof of
   ownership, as it is defined in this memo, is not possible anymore
   when using this aggregated way.  However, the outbound NF can use the
   relationship between the information of the received CREATE or EXT
   message and the GIST messaging association where the request has been
   received.  The outbound NF MUST only accept this aggregated CREATE or
   EXT message through already established GIST messaging associations
   with the NI.  The outbound NF MUST NOT propagate this aggregated
   CREATE or EXT message but it MAY generate and forward per NATFW NSLP
   signaling session CREATE or EXT messages.

3.7.5.  Reporting Asynchronous Events

   NATFW NSLP forwarders and NATFW NSLP responders must have the ability
   to report asynchronous events to other NATFW NSLP nodes, especially
   to allow reporting back to the NATFW NSLP initiator.  Such
   asynchronous events may be premature NATFW NSLP signaling session
   termination, changes in local policies, route change or any other
   reason that indicates change of the NATFW NSLP signaling session
   state.

   NFs and NRs may generate NOTIFY messages upon asynchronous events,
   with a NATFW_INFO object indicating the reason for event.  These
   reasons can be carried in the NATFW_INFO object (class MUST be set to
   'Informational' (0x1)) within the NOTIFY message.  This list shows
   the response codes and the associated actions to take at NFs and the
   NI:

   o  'Route change: possible route change on the outbound path' (0x01):
      Follow instructions in Section 3.9.  This MUST be sent inbound.

   o  'Re-authentication required' (0x02): The NI should re-send the
      authentication.  This MUST be sent inbound.

   o  'NATFW node is going down soon' (0x03): The NI and other NFs
      should be prepared for a service interruption at any time.  This
      message MAY be sent inbound and outbound.



Stiemerling, et al.     Expires January 10, 2008               [Page 44]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  'NATFW signaling session lifetime expired' (0x04): The NATFW
      signaling session has been expired and the signaling session is
      invalid now.  NFs MUST mark the signaling session as 'Dead'.  This
      message MAY be sent inbound and outbound.

   NOTIFY messages are always sent hop-by-hop inbound towards NI until
   they reach NI or outbound towards the NR as indicated in the list
   above.

   The initial processing when receiving a NOTIFY message is the same
   for all NATFW nodes: NATFW nodes MUST only accept NOTIFY messages
   through already established NTLP messaging associations.  The further
   processing is different for each NATFW NSLP node type and depends on
   the events notified:

   o  NSLP initiator: NIs analyze the notified event and behave
      appropriately based on the event type.  NIs MUST NOT generate
      NOTIFY messages.

   o  NSLP forwarder: NFs analyze the notified event and behave based on
      the above description per response code.  NFs SHOULD generate
      NOTIFY messages upon asynchronous events and forward them inbound
      towards the NI or outbound towards the NR, depending on the
      received direction, i.e., inbound messages MUST be forwarded
      further inbound and outbound messages MUST be forwarded further
      inbound.  NFs MUST silently discard NOTIFY messages that have been
      received outbound but are only allowed to be sent inbound, e.g.
      'Re-authentication required' (0x02).

   o  NSLP responder: NRs SHOULD generate NOTIFY messages upon
      asynchronous events including a response code based on the
      reported event.  The NR MUST silently discard NOTIFY messages that
      have been received outbound but are only allowed to be sent
      inbound, e.g.  'Re-authentication required' (0x02),

   NATFW NSLP forwarders, keeping multiple NATFW NSLP signaling sessions
   at the same time, can experience problems when shutting down service
   suddenly.  This sudden shutdown can be result of node local failure,
   for instance, due to a hardware failure.  This NF generates NOTIFY
   messages for each of the NATFW NSLP signaling sessions and tries to
   send them inbound.  Due to the number of NOTIFY messages to be sent,
   the shutdown of the node may be unnecessarily prolonged, since not
   all messages can be sent at the same time.  This case can be
   described as a NOTIFY storm, if a multitude of NATFW NSLP signaling
   sessions is involved.

   To avoid the need of generating per NATFW NSLP signaling session
   NOTIFY messages in such a scenario described or similar cases, NFs



Stiemerling, et al.     Expires January 10, 2008               [Page 45]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   SHOULD follow this procedure: The NF uses the NOTIFY message with the
   session ID in the NTLP set to zero, with the MRI completely
   wildcarded, using the 'explicit routing' as described in Sections
   5.2.1 and 7.1.4. in [2].  The inbound NF receiving this type of
   NOTIFY immediately regards all NATFW NSLP signaling sessions from
   that peer matching the MRI as void.  This message will typically
   result in multiple NOTIFY messages at the inbound NF, i.e., the NF
   can generate per terminated NATFW NSLP signaling session a NOTIFY
   message.  However, a NF MAY aggregate again the NOTIFY messages as
   described here.

3.7.6.  Proxy Mode of Operation

   Some migration scenarios need specialized support to cope with cases
   where NSIS is only deployed in same areas of the Internet.  End-to-
   end signaling is going to fail without NSIS support at or near both
   data sender and data receiver terminals.  A proxy mode of operation
   is needed.  This proxy mode of operation must terminate the NATFW
   NSLP signaling as topologically close to the terminal for which it is
   proxying and proxy all messages.  This NATFW NSLP node doing the
   proxying of the signaling messages becomes either the NI or the NR
   for the particular NATFW NSLP signaling session, depending on whether
   it is the DS or DR that does not support NSIS.  Typically, the edge-
   NAT or the edge-firewall would be used to proxy NATFW NSLP messages.

   This proxy mode operation does not require any new CREATE or EXT
   message type, but relies on extended CREATE and EXT message types.
   They are called respectively CREATE-PROXY and EXT-PROXY and are
   distinguished by setting the P flag in the NSLP header to P=1.  This
   flag instructs edge-NATs and edge-firewalls receiving them to operate
   in proxy mode for the NATFW NSLP signaling session in question.  The
   semantics of the CREATE and EXT message types are not changed and the
   behavior of the various node types is as defined in Section 3.7.1 and
   Section 3.7.2, except for the proxying node.  The following
   paragraphs describe the proxy mode operation for data receivers
   behind middleboxes and data senders behind middleboxes.

3.7.6.1.  Proxying for a Data Sender

   The NATFW NSLP gives the NR the ability to install state on the
   inbound path towards the data sender for outbound data packets, even
   when only the receiving side is running NSIS (as shown in Figure 18).
   The goal of the method described is to trigger the edge-NAT/
   edge-firewall to generate a CREATE message on behalf of the data
   receiver.  In this case, an NR can signal towards the network border
   as it is performed in the standard EXT message handling scenario as
   in Section 3.7.2.  The message is forwarded until the edge-NAT/
   edge-firewall is reached.  A public IP address and port number is



Stiemerling, et al.     Expires January 10, 2008               [Page 46]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   reserved at an edge-NAT/edge-firewall.  As shown in Figure 18, unlike
   the standard EXT message handling case, the edge-NAT/edge-firewall is
   triggered to send a CREATE message on a new reverse path which
   traverse several firewalls or NATs.  The new reverse path for CREATE
   is necessary to handle routing asymmetries between the edge-NAT/
   edge-firewall and DR.  It must be stressed that the semantics of the
   CREATE and EXT messages is not changed, i.e., each is processed as
   described earlier.


      DS       Public Internet     NAT/FW    Private address      NR
     No NI                            NF         space            NI+
      NR+

      |                               |   EXT-PROXY[(DTInfo)]     |
      |                               |<------------------------- |
      |                               |  RESPONSE[Error/Success]  |
      |                               | ---------------------- >  |
      |                               |   CREATE                  |
      |                               | ------------------------> |
      |                               |  RESPONSE[Error/Success]  |
      |                               | <----------------------   |
      |                               |                           |

            Figure 18: EXT Triggering Sending of CREATE Message

   A NATFW_NONCE object, carried in the EXT and CREATE message, is used
   to build the relationship between received CREATEs at the message
   initiator.  An NI+ uses the presence of the NATFW_NONCE object to
   correlate it to the particular EXT-PROXY.  The absence of a NONCE
   object indicates a CREATE initiated by the DS and not by the edge-
   NAT.  Therefore, these processing rules of EXT-PROXY messages are
   added to the regular EXT processing:

   o  NSLP initiator (NI+): The NI+ MUST choose a random value and place
      it in the NATFW_NONCE object.

   o  NSLP forwarder being either edge-NAT or edge-firewall: When the NF
      accepts a EXT_PROXY message, it generates a successful RESPONSE
      message as if it were the NR and additionally, it generates a
      CREATE message as defined in Section 3.7.1 and includes a
      NATFW_NONCE object having the same value as of the received
      NATFW_NONCE object.  The NF MUST not generate a CREATE-PROXY
      message.  The NF MUST refresh the CREATE message signaling session
      only if a EXT-PROXY refresh message has been received first.  This
      also includes tearing down signaling sessions, i.e., the NF must
      teardown the CREATE signaling session only if a EXT-PROXY message
      with lifetime set to 0 has been received first.



Stiemerling, et al.     Expires January 10, 2008               [Page 47]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   The scenario described in this section challenges the data receiver
   because it must make a correct assumption about the data sender's
   ability to use NSIS NATFW NSLP signaling.  It is possible for the DR
   to make the wrong assumption in two different ways:

      a) the DS is NSIS unaware but the DR assumes the DS to be NSIS
      aware and

      b) the DS is NSIS aware but the DR assumes the DS to be NSIS
      unaware.

   Case a) will result in middleboxes blocking the data traffic, since
   DS will never send the expected CREATE message.  Case b) will result
   in the DR successfully requesting proxy mode support by the edge-NAT
   or edge-firewall.  The edge-NAT/edge-firewall will send CREATE
   messages and DS will send CREATE messages as well.  Both CREATE
   messages are handled as separated NATFW NSLP signaling sessions and
   therefore the common rules per NATFW NSLP signaling session apply;
   the NATFW_NONCE object is used to differentiate CREATE messages
   generated by the edge-NAT/edge-firewall from NI initiated CREATE
   messages.  It is the NR's responsibility to decide whether to
   teardown the EXT-PROXY signaling sessions in the case where the data
   sender's side is NSIS aware, but was incorrectly assumed not to be so
   by the DR.  It is RECOMMENDED that a DR behind NATs uses the proxy
   mode of operation by default, unless the DR knows that the DS is NSIS
   aware.  The DR MAY cache information about data senders which it has
   found to be NSIS aware in past NATFW NSLP signaling sessions.

   There is a possible race condition between the RESPONSE message to
   the EXT-PROXY and the CREATE message generated by the edge-NAT.  The
   CREATE message can arrive earlier than the RESPONSE message.  An NI+
   MUST accept CREATE messages generated by the edge-NAT even if the
   RESPONSE message to the EXT-PROXY was not received.

3.7.6.2.  Proxying for a Data Receiver

   As with data receivers behind middleboxes, data senders behind
   middleboxes can require proxy mode support.  The issue here is that
   there is no NSIS support at the data receiver's side and, by default,
   there will be no response to CREATE messages.  This scenario requires
   the last NSIS NATFW NSLP aware node to terminate the forwarding and
   to proxy the response to the CREATE message, meaning that this node
   is generating RESPONSE messages.  This last node may be an edge-NAT/
   edge-firewall, or any other NATFW NSLP peer, that detects that there
   is no NR available (probably as a result of GIST timeouts but there
   may be other triggers).





Stiemerling, et al.     Expires January 10, 2008               [Page 48]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


      DS       Private Address      NAT/FW   Public Internet      NR
      NI           Space              NF                         no NR

      |                               |                           |
      |         CREATE-PROXY          |                           |
      |------------------------------>|                           |
      |                               |                           |
      |   RESPONSE[SUCCESS/ERROR]     |                           |
      |<------------------------------|                           |
      |                               |                           |

                 Figure 19: Proxy Mode CREATE Message Flow

   The processing of CREATE-PROXY messages and RESPONSE messages is
   similar to Section 3.7.1, except that forwarding is stopped at the
   edge-NAT/edge-firewall.  The edge-NAT/edge-firewall responds back to
   NI according the situation (error/success) and will be the NR for
   future NATFW NSLP communication.

   The NI can choose the proxy mode of operation although the DR is NSIS
   aware.  The CREATE-PROXY mode would not configure all NATs and
   firewalls along the data path, since it is terminated at the edge-
   device.  Any device beyond this point will never receive any NATFW
   NSLP signaling for this flow.

3.8.  De-Multiplexing at NATs

   Section 3.7.2 describes how NSIS nodes behind NATs can obtain a
   public reachable IP address and port number at a NAT and and how the
   resulting mapping rule can be activated by using CREATE messages (see
   Section 3.7.1).  The information about the public IP address/port
   number can be transmitted via an application level signaling protocol
   and/or third party to the communication partner that would like to
   send data toward the host behind the NAT.  However, NSIS signaling
   flows are sent towards the address of the NAT at which this
   particular IP address and port number is allocated and not directly
   to the allocated IP address and port number.  The NATFW NSLP
   forwarder at this NAT needs to know how the incoming NSLP CREATE
   messages are related to reserved addresses, meaning how to de-
   multiplex incoming NSIS CREATE messages.

   The de-multiplexing method uses information stored at the local NATFW
   NSLP node and the of the policy rule.  The policy rule uses the LE-
   MRM MRI source-address (see [2]) as the flow destination IP address
   and the network-layer-version as IP version.  The external IP address
   at the NAT is stored as the external flow destination IP address.
   All other parameters of the policy rule other than the flow
   destination IP address are wildcarded if no NATFW_DTINFO object is



Stiemerling, et al.     Expires January 10, 2008               [Page 49]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   included in the EXT message.  The LE-MRM MRI destination-address MUST
   NOT be used in the policy rule, since it is solely a signaling
   destination address.

   If the NATFW_DTINFO object is included in the EXT message, the policy
   rule is filled with further information.  The 'dst port number' field
   of the NATFW_DTINFO is stored as the flow destination port number.
   The 'protocol' field is stored as the flow protocol.  The 'src port
   number' field is stored as the flow source port number.  The 'data
   sender's IPv4 address' is stored as the flow source IP address.  Note
   that some of these field can contain wildcards.

   When receiving a CREATE message at the NATFW NSLP it uses the flow
   information stored in the MRI to do the matching process.  This table
   shows the parameters to be compared against each others.  Note that
   not all parameters can be present in a MRI at the same time.

    +-------------------------------+--------------------------------+
    |  Flow parameter (Policy Rule) | MRI parameter (CREATE message) |
    +-------------------------------+--------------------------------+
    |           IP version          |      network-layer-version     |
    |                               |                                |
    |            Protocol           |           IP-protocol          |
    |                               |                                |
    |     source IP address (w)     |       source-address (w)       |
    |                               |                                |
    |      external IP address      |       destination-address      |
    |                               |                                |
    |  destination IP address (n/u) |               N/A              |
    |                               |                                |
    |     source port number (w)    |       L4-source-port (w)       |
    |                               |                                |
    |    external port number (w)   |     L4-destination-port (w)    |
    |                               |                                |
    | destination port number (n/u) |               N/A              |
    |                               |                                |
    |           IPsec SPI           |            ipsec-SPI           |
    +-------------------------------+--------------------------------+

    Table entries marked with (w) can be wildcarded and entries marked
                 with (n/u) are not used for the matching.

                                  Table 1








Stiemerling, et al.     Expires January 10, 2008               [Page 50]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


3.9.  Reacting to Route Changes

   The NATFW NSLP needs to react to route changes in the data path.
   This assumes the capability to detect route changes, to perform NAT
   and firewall configuration on the new path and possibly to tear down
   NATFW NSLP signaling session state on the old path.  The detection of
   route changes is described in Section 7 of [2] and the NATFW NSLP
   relies on notifications about route changes by the NTLP.  This
   notification will be conveyed by the API between NTLP and NSLP, which
   is out of scope of this memo.

   A NATFW NSLP node other than the NI or NI+ detecting a route change,
   by means described in the NTLP specification or others, generates a
   NOTIFY message indicating this change and sends this inbound towards
   NI.  Intermediate NFs on the way to the NI can use this information
   to decide later if their NATFW NSLP signaling session can be deleted
   locally, if they do not receive an update within a certain time
   period, as described in Section 3.2.3.  It is important to consider
   the transport limitations of NOTIFY messages as mandated in
   Section 3.7.5.

   The NI receiving this NOTIFY message MAY generate a new CREATE or EXT
   message and sends it towards the NATFW NSLP signaling session's NI as
   for the initial message using the same session ID.  All the remaining
   processing and message forwarding, such as NSLP next hop discovery,
   is subject to regular NSLP processing as described in the particular
   sections.  Normal routing will guide the new CREATE or EXT message to
   the correct NFs along the changed route.  NFs that were on the
   original path receiving these new CREATE or EXT messages (see also
   Section 3.10), can use the session ID to update the existing NATFW
   NSLP signaling session, whereas NFs that were not on the original
   path will create new state for this NATFW NSLP signaling session.
   The next section describes how policy rules are updated.

3.10.  Updating Policy Rules

   NSIS initiators can request an update of the installed/reserved
   policy rules at any time within a NATFW NSLP signaling session.
   Updates to policy rules can be required due to node mobility (NI is
   moving from one IP address to another), route changes (this can
   result in a different NAT mapping at a different NAT device), or the
   wish of the NI to simply change the rule.  NIs can update policy
   rules in existing NATFW NSLP signaling sessions by sending an
   appropriate CREATE or EXT message (similar to Section 3.4) with
   modified message routing information (MRI) as compared with that
   installed previously, but using the existing session ID to identify
   the intended target of the update.  With respect to authorization and
   authentication, this update CREATE or EXT message is treated in



Stiemerling, et al.     Expires January 10, 2008               [Page 51]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   exactly the same way as any initial message.  Therefore, any node
   along in the NATFW NSLP signaling session can reject the update with
   an error RESPONSE message, as defined in the previous sections.

   The message processing and forwarding is executed as defined in the
   particular sections.  A NF or the NR receiving an update, simply
   replaces the installed policy rules installed in the firewall/NAT.
   The local procedures on how to update the MRI in the firewall/NAT is
   out of scope of this memo










































Stiemerling, et al.     Expires January 10, 2008               [Page 52]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


4.  NATFW NSLP Message Components

   A NATFW NSLP message consists of a NSLP header and one or more
   objects following the header.  The NSLP header is carried in all
   NATFW NSLP message and objects are Type-Length-Value (TLV) encoded
   using big endian (network ordered) binary data representations.
   Header and objects are aligned to 32 bit boundaries and object
   lengths that are not multiples of 32 bits must be padded to the next
   higher 32 bit multiple.

   The whole NSLP message is carried as payload of a NTLP message.

   Note that the notation 0x is used to indicate hexadecimal numbers.

4.1.  NSLP Header

   All GIST NSLP-Data objects for the NATFW NSLP MUST contain this
   common header as the first 32 bits of the object (this is not the
   same as the GIST Common Header).  It contains two fields, the NSLP
   message type and a reserved field.  The total length is 32 bits.  The
   layout of the NSLP header is defined by Figure 20.


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Message type  |P| reserved    |       reserved                |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 20: Common NSLP header

   The reserved field MUST be set to zero in the NATFW NSLP header
   before sending and MUST be ignored during processing of the header.

   The defined messages types are:

   o  IANA-TBD(1) : CREATE

   o  IANA-TBD(2) : EXTERNAL(EXT)

   o  IANA-TBD(3) : RESPONSE

   o  IANA-TBD(4) : NOTIFY

   If a message with another type is received, an error RESPONSE of
   class 'Protocol error' (0x3) with response code 'Illegal message
   type' (0x01) MUST be generated.




Stiemerling, et al.     Expires January 10, 2008               [Page 53]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   The P flag indicates the usage of proxy mode.  If proxy mode is used
   it MUST be set to 1.  Proxy mode usage is only allowed in combination
   with the message types CREATE and EXT, P=1 MUST NOT be set with
   message types other than CREATE and EXT.  The P flag MUST be ignored
   when processing messages with type RESPONSE.  An error RESPONSE
   message of class 'Protocol error' (0x3) and type 'Bad flags value'
   (0x03) MUST be generated, if the P flag is set in NOTIFY messages.

4.2.  NSLP Objects

   NATFW NSLP objects use a common header format defined by Figure 21.
   The object header contains two fields, the NSLP object type and the
   object length.  Its total length is 32 bits.


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |A|B|r|r|   Object Type         |r|r|r|r|   Object Length       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                   Figure 21: Common NSLP object header

   The object length field contains the total length of the object
   without the object header.  The unit is a word, consisting of 4
   octets.  The particular values of type and length for each NSLP
   object are listed in the subsequent sections that define the NSLP
   objects.  An error RESPONSE of class 'Protocol error' (0x3) with
   response code 'Wrong object length' (0x07) MUST be generated if the
   length given for the object in the object header did not match the
   length of the object data present.  The two leading bits of the NSLP
   object header are used to signal the desired treatment for objects
   whose treatment has not been defined in this memo (see [2], Section
   A.2.1), i.e., the Object Type has not been defined.  NATFW NSLP uses
   a subset of the categories defined in GIST:

   o  AB=00 ("Mandatory"): If the object is not understood, the entire
      message containing it MUST be rejected with an error RESPONSE of
      class 'Protocol error' (0x3) with response code 'Unknown object
      present' (0x06).

   o  AB=01 ("Optional"): If the object is not understood, it should be
      deleted and then the rest of the message processed as usual.

   o  AB=10 ("Forward"): If the object is not understood, it should be
      retained unchanged in any message forwarded as a result of message
      processing, but not stored locally.




Stiemerling, et al.     Expires January 10, 2008               [Page 54]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   The combination AB=11 MUST NOT be used and an error RESPONSE of class
   'Protocol error' (0x3) with response code 'Invalid Flag-Field
   combination' (0x09) MUST be generated.

   The following sections do not repeat the common NSLP object header,
   they just list the type and the length.

4.2.1.  Signaling Session Lifetime Object

   The signaling session lifetime object carries the requested or
   granted lifetime of a NATFW NSLP signaling session measured in
   seconds.

      Type: NATFW_LT (IANA-TBD)

      Length: 1


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          NATFW NSLP signaling session lifetime                |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

               Figure 22: Signaling Session Lifetime object

4.2.2.  External Address Object

   The external address object can be included in RESPONSE messages
   (Section 4.3.3) only.  It carries the publicly reachable IP address,
   and if applicable port number, at an edge-NAT.

      Type: NATFW_EXT_IP (IANA-TBD)

      Length: 2


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         port number           |           reserved            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                           IPv4 address                        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 23: External Address Object for IPv4 addresses

   Please note that the field 'port number' MUST be set to 0 if only an



Stiemerling, et al.     Expires January 10, 2008               [Page 55]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   IP address has been reserved, for instance, by a traditional NAT.  A
   port number of 0 MUST be ignored in processing this object.

4.2.3.  Extended Flow Information Object

   In general, flow information is kept in the message routing
   information (MRI) of the NTLP.  Nevertheless, some additional
   information may be required for NSLP operations.  The 'extended flow
   information' object carries this additional information about the
   action of the policy rule for firewalls/NATs and contiguous port .

      Type: NATFW_EFI (IANA-TBD)

      Length: 1


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           rule action         |           sub_ports           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                   Figure 24: Extended Flow Information

   This object has two fields, 'rule action' and 'sub_ports'.  The 'rule
   action' field has these meanings:

   o  0x0001: Allow: A policy rule with this action allows data traffic
      to traverse the middlebox and the NATFW NSLP MUST allow NSLP
      signaling to be forwarded.

   o  0x0002: Deny: A policy rule with this action blocks data traffic
      from traversing the middlebox and the NATFW NSLP MUST NOT allow
      NSLP signaling to be forwarded.

   If the 'rule action' field contains neither 0x0001 nor 0x0002, an
   error RESPONSE of class 'Signaling session error' (0x6) with response
   code 'Unknown policy rule action' (0x05) MUST be generated.

   The 'sub_ports' field contains the number of contiguous transport
   layer ports to which this rule applies.  The default value of this
   field is 0, i.e., only the port specified in the NTLP's MRM or
   NATFW_DTINFO object is used for the policy rule.  A value of 1
   indicates that additionally to the port specified in the NTLP's MRM
   (port1), a second port (port2) is used.  This value of port 2 is
   calculated as: port2 = port1 + 1.  Other values than 0 or 1 MUST NOT
   be used in this field and an error RESPONSE of class 'Signaling
   session error' (0x6) with response code 'Requested value in sub_ports



Stiemerling, et al.     Expires January 10, 2008               [Page 56]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   field in NATFW_EFI not permitted' (0x08) MUST be generated.  Further
   version of this memo may allow other values for the 'sub_ports'
   field.  This two contiguous port numbered ports, can be used by
   legacy voice over IP equipment.  This legacy equipment assumes that
   two adjacent port numbers for its RTP/RTCP flows respectively.

4.2.4.  Information Code Object

   This object carries the response code, which may be indications for
   either a successful or failed CREATE or EXT message depending on the
   value of the 'response code' field.

      Type: NATFW_INFO (IANA-TBD)

      Length: 1


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Resv. | Class | Response Code |r|r|r|r|     Object Type       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 25: Information Code Object

   The field 'resv.' is reserved for future extensions and MUST be set
   to zero when generating such an object and MUST be ignored when
   receiving.  The 'Object Type' field contains the type of the object
   causing the error.  The value of 'Object Type' is set to 0, if no
   object is concerned and the leading fours bits marked with 'r' are
   always set to zero and ignored.  The 4 bit class field contains the
   severity class.  The following classes are defined:

   o  0x1: Informational (NOTIFY only)

   o  0x2: Success

   o  0x3: Protocol error

   o  0x4: Transient failure

   o  0x5: Permanent failure

   o  0x6: Signaling session failures

   Within each severity class a number of responses values are defined





Stiemerling, et al.     Expires January 10, 2008               [Page 57]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  Informational:

      *  0x01: Route change: possible route change on the outbound path.

      *  0x02: Re-authentication required.

      *  0x03: NATFW node is going down soon.

   o  Success:

      *  0x01: All successfully processed.

   o  Protocol error:

      *  0x01: Illegal message type: the type given in the Message Type
         field of the NSLP header is unknown.

      *  0x02: Wrong message length: the length given for the message in
         the NSLP header does not match the length of the message data.

      *  0x03: Bad flags value: an undefined flag or combination of
         flags was set in the NSLP header.

      *  0x04: Mandatory object missing: an object required in a message
         of this type was missing.

      *  0x05: Illegal object present: an object was present which must
         not be used in a message of this type.

      *  0x06: Unknown object present: an object of an unknown type was
         present in the message.

      *  0x07: Wrong object length: the length given for the object in
         the object header did not match the length of the object data
         present.

      *  0x08: Unknown object field value: a field in an object had an
         unknown value.

      *  0x09: Invalid Flag-Field combination: An object contains an
         invalid combination of flags and/or fields.

      *  0x0A: Duplicate object present.

      *  0x0B: Received EXT request message on external side.






Stiemerling, et al.     Expires January 10, 2008               [Page 58]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   o  Transient failure:

      *  0x01: Requested resources temporarily not available.

   o  Permanent failure:

      *  0x01: Authentication failed.

      *  0x02: Authorization failed.

      *  0x03: Unable to agree transport security with peer.

      *  0x04: Internal or system error.

      *  0x05: No NAT here.

      *  0x06: No edge-device here.

      *  0x07: Did not reach the NR.

   o  Signaling session failures:

      *  0x01: Session terminated asynchronously.

      *  0x02: Requested lifetime is too big.

      *  0x03: No reservation found matching the MRI of the CREATE
         request.

      *  0x04: Requested policy rule denied due to policy conflict.

      *  0x05: Unknown policy rule action.

      *  0x06: Requested rule action not applicable.

      *  0x07: NATFW_DTINFO object is required.

      *  0x08: Requested value in sub_ports field in NATFW_EFI not
         permitted.

      *  0x09: Requested IP protocol not supported.

      *  0x0A: Plain IP policy rules not permitted -- need transport
         layer information.

      *  0x0B: ICMP type value not permitted.





Stiemerling, et al.     Expires January 10, 2008               [Page 59]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


      *  0x0C: source IP address range is too large.

      *  0x0D: destination IP address range is too large.

      *  0x0E: source L4-port range is too large.

      *  0x0F: destination L4-port range is too large.

      *  0x10: Requested lifetime is too small.

4.2.5.  Nonce Object

   This object carries the nonce value as described in Section 3.7.6.

      Type: NATFW_NONCE (IANA-TBD)

      Length: 1


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                         nonce                                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                          Figure 26: Nonce Object

4.2.6.  Message Sequence Number Object

   This object carries the MSN value as described in Section 3.5.

      Type: NATFW_MSN (IANA-TBD)

      Length: 1


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                    message sequence number                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                 Figure 27: Message Sequence Number Object








Stiemerling, et al.     Expires January 10, 2008               [Page 60]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


4.2.7.  Data Terminal Information Object

   The 'data terminal information' object carries additional information
   possibly needed during EXT operations.  EXT messages are transported
   by the NTLP using the Loose-End message routing method (LE-MRM).  The
   LE-MRM contains only DR's IP address and a signaling destination
   address (destination address).  This destination address is used for
   message routing only and is not necessarily reflecting the address of
   the data sender.  This object contains information about (if
   applicable) DR's port number (the destination port number), DS' port
   number (the source port number), the used transport protocol, the
   prefix length of the IP address, and DS' IP address.

      Type: NATFW_DTINFO (IANA-TBD)

      Length: variable.  Maximum 3.


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |I|P|S|    reserved             | sender prefix |    protocol   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     :      DR port number           |       DS port number          :
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     :                            IPsec SPI                          :
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                  data sender's IPv4 address                   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

               Figure 28: Data Terminal IPv4 Address Object

   The flags are:

   o  I: I=1 means that 'protocol' should be interpreted.

   o  P: P=1 means that 'dst port number' and 'src port number' are
      present and should be interpreted.

   o  S: S=1 means that SPI is present and should be interpreted.

   The SPI field is only present if S is set.  The port numbers are only
   present if P is set.  The flags P and S MUST NOT be set at the same
   time.  An error RESPONSE of class 'Protocol error' (0x3) with
   response code 'Invalid Flag-Field combination' (0x09) MUST be
   generated if they are both set.  If either P or S is set, I MUST be
   set as well and the protocol field MUST carry the particular
   protocol.  An error RESPONSE of class 'Protocol error' (0x3) with



Stiemerling, et al.     Expires January 10, 2008               [Page 61]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   response code 'Invalid Flag-Field combination' (0x09) MUST be
   generated if S or P is set but I is not set.

   The fields MUST be interpreted according these rules:

   o  (data) sender prefix: This parameter indicates the prefix length
      of the 'data sender's IP address' in bits.  For instance, a full
      IPv4 address requires 'sender prefix' to be set to 32.  A value of
      0 indicates an IP address wildcard.

   o  protocol: The IPv4 protocol field.  This field MUST be interpreted
      if I=1, otherwise it MUST be set to 0 and MUST be ignored.

   o  DR port number: The port number at the data receiver (DR), i.e.,
      the destination port.  A value of 0 indicates a port wildcard,
      i.e., the destination port number is not known.  Any other value
      indicates the destination port number.

   o  DS port number: The port number at the data sender (DS), i.e., the
      source port.  A value of 0 indicates a port wildcard, i.e., the
      source port number is not known.  Any other value indicates the
      source port number.

   o  data sender's IPv4 address: The source IP address of the data
      sender.  This field MUST be set to zero if no IP address is
      provided, i.e., a complete wildcard is desired (see dest prefix
      field above).

4.2.8.  ICMP Types Object

   The 'ICMP types' object contains additional information needed to
   configure a NAT of firewall with rules to control ICMP traffic.  The
   object contains a number of values of the ICMP Type field for which a
   filter action should be set up:

      Type: NATFW_ICMP_TYPES (IANA-TBD)

      Length: Variable = ((Number of Types carried + 1) + 3) DIV 4

   Where DIV is an integer division.











Stiemerling, et al.     Expires January 10, 2008               [Page 62]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    Count      |     Type      |      Type     |    ........   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       ................                        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    ........   |     Type      |           (Padding)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 29: ICMP Types Object

   The fields MUST be interpreted according these rules:

      count: 8 bit integer specifying the number of 'Type' entries in
      the object.

      type: 8 bit field specifying an ICMP Type value to which this rule
      applies.

      padding: Sufficient 0 bits to pad out the last word so that the
      total size of object is an even multiple of words.  Ignored on
      reception.

4.3.  Message Formats

   This section defines the content of each NATFW NSLP message type.
   The message types are defined in Section 4.1.

   Basically, each message is constructed of NSLP header and one or more
   NSLP objects.  The order of objects is not defined, meaning that
   objects may occur in any sequence.  Objects are marked either with
   mandatory (M) or optional (O).  Where (M) implies that this
   particular object MUST be included within the message and where (O)
   implies that this particular object is OPTIONAL within the message.
   Objects defined in this memo carry always the flag combination AB=00
   in the NSLP object header.  An error RESPONSE message of class
   'Protocol error' (0x3) with response code 'Mandatory object missing'
   (0x02) MUST be generated if a mandatory declared object is missing.
   An error RESPONSE message of class 'Protocol error' (0x3) with
   response code 'Illegal object present' (0x05) MUST be generated if an
   object was present which must not be used in a message of this type.
   An error RESPONSE message of class 'Protocol error' (0x3) with
   response code 'Duplicate object present' (0x0A) MUST be generated if
   an object appears more than once in a message.

   Each section elaborates the required settings and parameters to be
   set by the NSLP for the NTLP, for instance, how the message routing



Stiemerling, et al.     Expires January 10, 2008               [Page 63]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   information is set.

4.3.1.  CREATE

   The CREATE message is used to create NATFW NSLP signaling sessions
   and to create policy rules.  Furthermore, CREATE messages are used to
   refresh NATFW NSLP signaling sessions and to delete them.

   The CREATE message carries these objects:

   o  Signaling Session Lifetime object (M)

   o  Extended flow information object (M)

   o  Message sequence number object (M)

   o  Nonce object (M) if P flag set to 1 in the NSLP header, otherwise
      (O)

   o  ICMP Types Object (O)

   The message routing information in the NTLP MUST be set to DS as
   source address and DR as destination address.  All other parameters
   MUST be set according the required policy rule.  CREATE messages MUST
   be transported by using the path-coupled MRM with direction set to
   'downstream' (outbound).

4.3.2.  EXTERNAL (EXT)

   The EXTERNAL (EXT) message is used to a) reserve an external IP
   address/port at NATs, b) to notify firewalls about NSIS capable DRs,
   or c) to block incoming data traffic at inbound firewalls.

   The EXT message carries these objects:

   o  Signaling Session Lifetime object (M)

   o  Message sequence number object (M)

   o  Extended flow information object (M)

   o  Data terminal information object (M)

   o  Nonce object [M if P flag set to 1 in the NSLP header, otherwise
      (O)

   o  ICMP Types Object (O)




Stiemerling, et al.     Expires January 10, 2008               [Page 64]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   The selected message routing method of the EXT message depends on a
   number of considerations.  Section 3.7.2 describes it exhaustively
   how to select the correct method.  EXT messages can be transported
   via the path-coupled message routing method (PC-MRM) or via the
   loose-end message routing method (LE-MRM).  In the case of PC-MRM,
   the source-address is set to DS' address and the destination address
   is set to DR's address, the direction is set to inbound.  In the case
   of LE-MRM, the destination-address is set to DR's address or to the
   signaling destination address.  The source-address is set to DS's
   address.

4.3.3.  RESPONSE

   RESPONSE messages are responses to CREATE and EXT messages.  RESPONSE
   messages MUST NOT be generated for any other message, such as NOTIFY
   and RESPONSE.

   The RESPONSE message for the class 'Success' (0x2) carries these
   objects:

   o  Signaling Session Lifetime object (M)

   o  Message sequence number object (M)

   o  Information code object (M)

   o  External address object (O)

   The RESPONSE message for other classes than 'Success' (0x2) carries
   these objects:

   o  Message sequence number object (M)

   o  Information code object (M)

   This message is routed towards the NI hop-by-hop, using existing NTLP
   messaging associations.  The MRM used for this message MUST be the
   same as MRM used by the corresponding CREATE or EXT message.

4.3.4.  NOTIFY

   The NOTIFY messages is used to report asynchronous events happening
   along the signaled path to other NATFW NSLP nodes.

   The NOTIFY message carries this object:

   o  Information code object (M).




Stiemerling, et al.     Expires January 10, 2008               [Page 65]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   The NOTIFY message is routed towards the NI hop-by-hop using the
   existing inbound node messaging association entry within the node's
   Message Routing State table.  The MRM used for this message MUST be
   the same as MRM used by the corresponding CREATE or EXT message.















































Stiemerling, et al.     Expires January 10, 2008               [Page 66]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


5.  Security Considerations

   Security is of major concern particularly in case of firewall
   traversal.  This section provides security considerations for the
   NAT/firewall traversal and is organized as follows.

   In Section 5.1 we describe the participating entities relate to each
   other from a security point of view.  This subsection also motivates
   a particular authorization model.

   Security threats that focus on NSIS in general are described in [8]
   and they are applicable to this document as well.

   Finally, we illustrate how the security requirements that were
   created based on the security threats can be fulfilled by specific
   security mechanisms.  These aspects will be elaborated in
   Section 5.2.

5.1.  Authorization Framework

   The NATFW NSLP is a protocol which may involve a number of NSIS nodes
   and is, as such, not a two-party protocol.  Figure 1 and Figure 2 of
   [8] already depict the possible set of communication patterns.  In
   this section we will re-evaluate these communication patters with
   respect to the NATFW NSLP protocol interaction.

   The security solutions for providing authorization have a direct
   impact on the treatment of different NSLPs.  As it can be seen from
   the QoS NSLP [6] and the corresponding Diameter QoS work [19]
   accounting and charging seems to play an important role for QoS
   reservations, whereas monetary aspects might only indirectly effect
   authorization decisions for NAT and firewall signaling.  Hence, there
   are differences in the semantic of authorization handling between QoS
   and NATFW signaling.  A NATFW aware node will most likely want to
   authorize the entity (e.g., user or machine) requesting the
   establishment of pinholes or NAT bindings.  The outcome of the
   authorization decision is either allowed or disallowed whereas a QoS
   authorization decision might indicate that a different set of QoS
   parameters is authorization (see [19] as an example).

5.1.1.  Peer-to-Peer Relationship

   Starting with the simplest scenario, it is assumed that neighboring
   nodes are able to authenticate each other and to establish keying
   material to protect the signaling message communication.  The nodes
   will have to authorize each other, additionally to the
   authentication.  We use the term 'Security Context' as a placeholder
   for referring to the entire security procedure, the necessary



Stiemerling, et al.     Expires January 10, 2008               [Page 67]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   infrastructure that needs to be in place in order for this to work
   (e.g., key management) and the established security related state.
   The required long-term key (symmetric or asymmetric keys) used for
   authentication are either made available using an out-of-band
   mechanism between the two NSIS NATFW nodes or they are dynamically
   established using mechanisms not further specified in this document.
   Note that the deployment environment will most likely have an impact
   on the choice of credentials being used.  The choice of these
   credentials used is also outside the scope of this document.


   +------------------------+              +-------------------------+
   |Network A               |              |                Network B|
   |              +---------+              +---------+               |
   |        +-///-+ Middle- +---///////----+ Middle- +-///-+         |
   |        |     |  box 1  | Security     |  box 2  |     |         |
   |        |     +---------+ Context      +---------+     |         |
   |        | Security      |              |  Security     |         |
   |        | Context       |              |  Context      |         |
   |        |               |              |               |         |
   |     +--+---+           |              |            +--+---+     |
   |     | Host |           |              |            | Host |     |
   |     |  A   |           |              |            |  B   |     |
   |     +------+           |              |            +------+     |
   +------------------------+              +-------------------------+

                   Figure 30: Peer-to-Peer Relationship

   Figure 30 shows a possible relationship between participating NSIS
   aware nodes.  Host A might be, for example, a host in an enterprise
   network that has keying material established (e.g., a shared secret)
   with the company's firewall (Middlebox 1).  The network administrator
   of Network A (company network) has created access control lists for
   Host A (or whatever identifiers a particular company wants to use).
   Exactly the same procedure might also be used between Host B and
   Middlebox 2 in Network B. For the communication between Middlebox 1
   and Middlebox 2 a security context is also assumed in order to allow
   authentication, authorization and signaling message protection to be
   successful.

5.1.2.  Intra-Domain Relationship

   In larger corporations, for example, a middlebox is used to protect
   individual departments.  In many cases, the entire enterprise is
   controlled by a single (or a small number of) security department,
   which gives instructions to the department administrators.  In such a
   scenario, the previously discussed peer-to-peer relationship might be
   prevalent.  Sometimes it might be necessary to preserve



Stiemerling, et al.     Expires January 10, 2008               [Page 68]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   authentication and authorization information within the network.  As
   a possible solution, a centralized approach could be used, whereby an
   interaction between the individual middleboxes and a central entity
   (for example a policy decision point - PDP) takes place.  As an
   alternative, individual middleboxes exchange the authorization
   decision with another middlebox within the same trust domain.
   Individual middleboxes within an administrative domain may exploit
   their relationship instead of requesting authentication and
   authorization of the signaling initiator again and again.  Figure 31
   illustrates a network structure which uses a centralized entity.


       +-----------------------------------------------------------+
       |                                               Network A   |
       |                      +---------+                +---------+
       |      +----///--------+ Middle- +------///------++ Middle- +---
       |      | Security      |  box 2  | Security       |  box 2  |
       |      | Context       +----+----+ Context        +----+----+
       | +----+----+               |                          |    |
       | | Middle- +--------+      +---------+                |    |
       | |  box 1  |        |                |                |    |
       | +----+----+        |                |                |    |
       |      | Security    |           +----+-----+          |    |
       |      | Context     |           | Policy   |          |    |
       |   +--+---+         +-----------+ Decision +----------+    |
       |   | Host |                     | Point    |               |
       |   |  A   |                     +----------+               |
       |   +------+                                                |
       +-----------------------------------------------------------+

                   Figure 31: Intra-domain Relationship

   The interaction between individual middleboxes and a policy decision
   point (or AAA server) is outside the scope of this document.

5.1.3.  End-to-Middle Relationship

   The peer-to-peer relationship between neighboring NSIS NATFW NSLP
   nodes might not always be sufficient.  Network B might require
   additional authorization of the signaling message initiator (in
   addition to the authorization of the neighboring node).  If
   authentication and authorization information is not attached to the
   initial signaling message then the signaling message arriving at
   Middlebox 2 would result in an error message being created, which
   indicates the additional authorization requirement.  In many cases
   the signaling message initiator might already be aware of the
   additionally required authorization before the signaling message
   exchange is executed.



Stiemerling, et al.     Expires January 10, 2008               [Page 69]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   Figure 32 shows this scenario.

       +--------------------+              +---------------------+
       |          Network A |              |Network B            |
       |                    |   Security   |                     |
       |          +---------+   Context    +---------+           |
       |    +-///-+ Middle- +---///////----+ Middle- +-///-+     |
       |    |     |  box 1  |      +-------+  box 2  |     |     |
       |    |     +---------+      |       +---------+     |     |
       |    |Security       |      |       | Security      |     |
       |    |Context        |      |       | Context       |
       |    |               |      |       |               |     |
       | +--+---+           |      |       |            +--+---+ |
       | | Host +----///----+------+       |            | Host | |
       | |  A   |           |   Security   |            |  B   | |
       | +------+           |   Context    |            +------+ |
       +--------------------+              +---------------------+

                   Figure 32: End-to-Middle Relationship

5.2.  Security Framework for the NAT/Firewall NSLP

   The following list of security requirements has been created to
   ensure proper secure operation of the NATFW NSLP.

5.2.1.  Security Protection between neighboring NATFW NSLP Nodes

   Based on the analyzed threats it is RECOMMENDED to provide, between
   neighboring NATFW NSLP nodes, the following mechanism:

   o  data origin authentication

   o  replay protection

   o  integrity protection and

   o  optionally confidentiality protection

   It is RECOMMENDED to use the authentication and key exchange security
   mechanisms provided in [2] between neighboring nodes when sending
   NATFW signaling messages.  The proposed security mechanisms of GIST
   provide support for authentication and key exchange in addition to
   denial of service protection.  Depending on the chosen security
   protocol, support for multiple authentication protocols might be
   provided.  If security between neighboring nodes is desired than the
   usage of C-MODE for the delivery of data packets and the usage of
   D-MODE only to discover the next NATFW NSLP aware node along the path
   is highly RECOMMENDED.  Almost all security threats at the NATFW NSLP



Stiemerling, et al.     Expires January 10, 2008               [Page 70]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   layer can be prevented by using a mutually authenticated Transport
   Layer secured connection and by relying on authorization by the
   neighboring NATFW NSLP entities.

   The NATFW NSLP relies on an established security association between
   neighboring peers to prevent unauthorized nodes to modify or delete
   installed state.  Between non-neighboring nodes the session ID (SID)
   carried in the NTLP is used to show ownership of a NATFW NSLP
   signaling session.  The session ID MUST be generated in a random way
   and thereby prevent an off-path adversary to mount targeted attacks.
   Hence, an adversary would have to learn the randomly generated
   session ID to perform an attack.  In a mobility environment a former
   on-path node that is now off-path can perform an attack.  Messages
   for a particular NATFW NSLP signaling session are handled by the NTLP
   to the NATFW NSLP for further processing.  Messages carrying a
   different session ID not associated with any NATFW NSLP are subject
   to the regular processing for new NATFW NSLP signaling sessions.

5.2.2.  Security Protection between non-neighboring NATFW NSLP Nodes

   Based on the security threats and the listed requirements it was
   noted that some threats also demand authentication and authorization
   of a NATFW signaling entity (including the initiator) towards a non-
   neighboring node.  This mechanism mainly demands entity
   authentication.  Additionally, security protection of certain
   payloads may be required between non-neighboring signaling entities
   and the Cryptographic Message Syntax (CMS) [14] migh be a potential
   solution.  Payload protection using CMS is not described in this
   document.  The most important information exchanged at the NATFW NSLP
   is information related to the establishment for firewall pinholes and
   NAT bindings.  This information can, however, not be protected over
   multiple NSIS NATFW NSLP hops since this information might change
   depending on the capability of each individual NATFW NSLP node.

   Some scenarios might also benefit from the usage of authorization
   tokens.  Their purpose is to associate two different signaling
   protocols (e.g., SIP and NSIS) and their authorization decision.
   These tokens are obtained by non-NSIS protocols, such as SIP or as
   part of network access authentication.  When a NAT or firewall along
   the path receives the token it might be verified locally or passed to
   the AAA infrastructure.  Examples of authorization tokens can be
   found in RFC 3520 [17] and RFC 3521 [18].  Figure 33 shows an example
   of this protocol interaction.

   An authorization token is provided by the SIP proxy, which acts as
   the assertion generating entity and gets delivered to the end host
   with proper authentication and authorization.  When the NATFW
   signaling message is transmitted towards the network, the



Stiemerling, et al.     Expires January 10, 2008               [Page 71]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   authorization token is attached to the signaling messages to refer to
   the previous authorization decision.  The assertion verifying entity
   needs to process the token or it might be necessary to interact with
   the assertion granting entity using HTTP (or other protocols).  As a
   result of a successfully authorization by a NATFW NSLP node, the
   requested action is executed and later a RESPONSE message is
   generated.


    +----------------+   Trust Relationship    +----------------+
    | +------------+ |<.......................>| +------------+ |
    | | Protocol   | |                         | | Assertion  | |
    | | requesting | |    HTTP, SIP Request    | | Granting   | |
    | | authz      | |------------------------>| | Entity     | |
    | | assertions | |<------------------------| +------------+ |
    | +------------+ |    Artifact/Assertion   |  Entity Cecil  |
    |       ^        |                         +----------------+
    |       |        |                          ^     ^|
    |       |        |                          .     || HTTP,
    |       |        |              Trust       .     || other
    |   API Access   |              Relationship.     || protocols
    |       |        |                          .     ||
    |       |        |                          .     ||
    |       |        |                          v     |v
    |       v        |                         +----------------+
    | +------------+ |                         | +------------+ |
    | | Protocol   | |  NSIS NATFW CREATE +    | | Assertion  | |
    | | using authz| |  Assertion/Artifact     | | Verifying  | |
    | | assertion  | | ----------------------- | | Entity     | |
    | +------------+ |                         | +------------+ |
    |  Entity Alice  | <---------------------- |  Entity Bob    |
    +----------------+   RESPONSE              +----------------+

                   Figure 33: Authorization Token Usage

   Threats against the usage of authorization tokens have been mentioned
   in [8].  Hence, it is required to provide confidentiality protection
   to avoid allowing an eavesdropper to learn the token and to use it in
   another NATFW NSLP signaling session (replay attack).  The token
   itself also needs to be protected against tempering.

   To harmonize the usage of authorization tokens in NSLPs a separate
   document is available, see [20].








Stiemerling, et al.     Expires January 10, 2008               [Page 72]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


6.  IAB Considerations on UNSAF

   UNilateral Self-Address Fixing (UNSAF) is described in [12] as a
   process at originating endpoints that attempt to determine or fix the
   address (and port) by which they are known to another endpoint.
   UNSAF proposals, such as STUN [15] are considered as a general class
   of workarounds for NAT traversal and as solutions for scenarios with
   no middlebox communication.

   This memo specifies a path-coupled middlebox communication protocol,
   i.e., the NSIS NATFW NSLP.  NSIS in general and the NATFW NSLP are
   not intended as a short-term workaround, but more as a long-term
   solution for middlebox communication.  In NSIS, endpoints are
   involved in allocating, maintaining, and deleting addresses and ports
   at the middlebox.  However, the full control of addresses and ports
   at the middlebox is at the NATFW NSLP daemon located to the
   respective NAT.

   Therefore, this document addresses the UNSAF considerations in [12]
   by proposing a long-term alternative solution.































Stiemerling, et al.     Expires January 10, 2008               [Page 73]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


7.  IANA Considerations

   This section provides guidance to the Internet Assigned Numbers
   Authority (IANA) regarding registration of values related to the
   NATFW NSLP, in accordance with BCP 26 RFC 2434 [13].

   The NATFW NSLP requires IANA to create a number of new registries.
   These registries may require further coordination with the registries
   of the NTLP [2] and the QoS NSLP [6].

   NATFW NSLP Message Type Registry

   The NATFW NSLP Message Type is a 8 bit value.  The allocation of
   values for new message types requires standards action.  Updates and
   deletion of values from the registry is not possible.  This
   specification defines four NATFW NSLP message types, which form the
   initial contents of this registry.  IANA is requested to add these
   four NATFW NSLP Message Types: CREATE, EXT, RESPONSE, and NOTIFY.

   NATFW NSLP Header Flag Registry

   NATFW NSLP messages have a messages-specific 8 bit flags/reserved
   field in their header.  The registration of flags is subject to IANA
   registration.  The allocation of values for flag types requires
   standards action.  Updates and deletion of values from the registry
   is not possible.  This specification defines only one flag, the P
   flag in Figure 20.

   NSLP Object Type Registry

   [Delete this part if already done by another NSLP:

   A new registry is to be created for NSLP Message Objects.  This is a
   12-bit field (giving values from 0 to 4095).  This registry is shared
   between a number of NSLPs.  Allocation policies are as follows:

      0-1023: Standards Action

      1024-1999: Specification Required

      2000-2047: Private/Experimental Use

      2048-4095: Reserved

   When a new object is defined, the extensbility bits (A/B) must also
   be defined.]

   This document defines 8 objects for the NATFW NSLP: NATFW_LT,



Stiemerling, et al.     Expires January 10, 2008               [Page 74]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   NATFW_EXT_IP, NATFW_EFI, NATFW_INFO, NATFW_NONCE, NATFW_MSN,
   NATFW_DTINFO, NATFW_ICMP_TYPES.  IANA is request to assigned values
   for them from NSLP Object Type registry and to replace the
   corresponding IANA-TBD tags with the numeric values.

   NSLP Response Code Registry

   In addition it defines a number of Response Codes for the NATFW NSLP.
   These can be found in Section 4.2.4 and are to be assigned values
   from NSLP Response Code registry.  The allocation of values for
   Response Codes Codes requires standards action.  IANA is request to
   assigned values for them from NSLP Response Code registry.

   Furthermore, IANA is requested to add a new value to the NSLP
   Identifiers (NSLPID) registry defined in [2] for the NATFW NSLP.




































Stiemerling, et al.     Expires January 10, 2008               [Page 75]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


8.  Open Issues

   A more detailed list of open issue can be found at:
   https://kobe.netlab.nec.de/roundup/nsis-natfw-nslp/index















































Stiemerling, et al.     Expires January 10, 2008               [Page 76]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


9.  Acknowledgments

   We would like to thank the following individuals for their
   contributions to this document at different stages:

   o  Marcus Brunner and Henning Schulzrinne for work on work on IETF
      drafts which lead us to start with this document,

   o  Miquel Martin for his help on the initial version of this
      document,

   o  Srinath Thiruvengadam and Ali Fessi work for their work on the
      NAT/firewall threats draft,

   o  Henning Peters for his comments and suggestions,

   o  and the NSIS working group.


































Stiemerling, et al.     Expires January 10, 2008               [Page 77]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


10.  References

10.1.  Normative References

   [1]   Bradner, S., "Key words for use in RFCs to Indicate Requirement
         Levels", BCP 14, RFC 2119, March 1997.

   [2]   Schulzrinne, H. and R. Hancock, "GIST: General Internet
         Signaling Transport", draft-ietf-nsis-ntlp-11 (work in
         progress), August 2006.

   [3]   Elz, R. and R. Bush, "Serial Number Arithmetic", RFC 1982,
         August 1996.

10.2.  Informative References

   [4]   Hancock, R., Karagiannis, G., Loughney, J., and S. Van den
         Bosch, "Next Steps in Signaling (NSIS): Framework", RFC 4080,
         June 2005.

   [5]   Brunner, M., "Requirements for Signaling Protocols", RFC 3726,
         April 2004.

   [6]   Manner, J., "NSLP for Quality-of-Service Signaling",
         draft-ietf-nsis-qos-nslp-12 (work in progress), October 2006.

   [7]   Srisuresh, P., Kuthan, J., Rosenberg, J., Molitor, A., and A.
         Rayhan, "Middlebox communication architecture and framework",
         RFC 3303, August 2002.

   [8]   Tschofenig, H. and D. Kroeselberg, "Security Threats for Next
         Steps in Signaling (NSIS)", RFC 4081, June 2005.

   [9]   Srisuresh, P. and M. Holdrege, "IP Network Address Translator
         (NAT) Terminology and Considerations", RFC 2663, August 1999.

   [10]  Carpenter, B. and S. Brim, "Middleboxes: Taxonomy and Issues",
         RFC 3234, February 2002.

   [11]  Braden, B., Zhang, L., Berson, S., Herzog, S., and S. Jamin,
         "Resource ReSerVation Protocol (RSVP) -- Version 1 Functional
         Specification", RFC 2205, September 1997.

   [12]  Daigle, L. and IAB, "IAB Considerations for UNilateral Self-
         Address Fixing (UNSAF) Across Network Address Translation",
         RFC 3424, November 2002.

   [13]  Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA



Stiemerling, et al.     Expires January 10, 2008               [Page 78]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


         Considerations Section in RFCs", BCP 26, RFC 2434,
         October 1998.

   [14]  Housley, R., "Cryptographic Message Syntax (CMS)", RFC 3852,
         July 2004.

   [15]  Rosenberg, J., Weinberger, J., Huitema, C., and R. Mahy, "STUN
         - Simple Traversal of User Datagram Protocol (UDP) Through
         Network Address Translators (NATs)", RFC 3489, March 2003.

   [16]  Westerinen, A., Schnizlein, J., Strassner, J., Scherling, M.,
         Quinn, B., Herzog, S., Huynh, A., Carlson, M., Perry, J., and
         S. Waldbusser, "Terminology for Policy-Based Management",
         RFC 3198, November 2001.

   [17]  Hamer, L-N., Gage, B., Kosinski, B., and H. Shieh, "Session
         Authorization Policy Element", RFC 3520, April 2003.

   [18]  Hamer, L-N., Gage, B., and H. Shieh, "Framework for Session
         Set-up with Media Authorization", RFC 3521, April 2003.

   [19]  Zorn, G., "Diameter Quality of Service Application",
         draft-ietf-dime-diameter-qos-00 (work in progress),
         February 2007.

   [20]  Manner, J., "Authorization for NSIS Signaling Layer Protocols",
         draft-manner-nsis-nslp-auth-02 (work in progress),
         October 2006.

   [21]  Roedig, U., Goertz, M., Karten, M., and R. Steinmetz, "RSVP as
         firewall Signalling Protocol", Proceedings of the 6th IEEE
         Symposium on Computers and Communications, Hammamet,
         Tunisia pp. 57 to 62, IEEE Computer Society Press, July 2001.


















Stiemerling, et al.     Expires January 10, 2008               [Page 79]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Appendix A.  Selecting Signaling Destination Addresses for EXT

   As with all other message types, EXT messages need a reachable IP
   address of the data sender on the GIST level.  For the path-coupled
   MRM the source-address of GIST is the reachable IP address (i.e., the
   real IP address of the data sender, or a wildcard).  While this is
   straight forward, it is not necessarily so for the loose-end MRM.
   Many applications do not provide the IP address of the communication
   counterpart, i.e., either the data sender or both a data sender and
   receiver.  For the EXT messages, the case of data sender is of
   interest only.  The rest of this section is giving informational
   guidance about determining a good destination-address of the LE-MRM
   in GIST for EXT messages.

   This signaling destination address (SDA, the destination-address in
   GIST) can be the data sender, but for applications which do not
   provide an address upfront, the destination address has to be chosen
   independently, as it is unknown at the time when the NATFW NSLP
   signaling has to start.  Choosing the 'correct' destination IP
   address may be difficult and it is possible that there is no 'right
   answer' for all applications relying on the NATFW NSLP.

   Whenever possible it is RECOMMENDED to chose the data sender's IP
   address as SDA.  It necessary to differentiate between the received
   IP addresses on the data sender.  Some application level signaling
   protocols (e.g., SIP) have the ability to transfer multiple contact
   IP addresses of the data sender.  For instance, private IP address,
   public IP address at NAT, and public IP address at a relay.  It is
   RECOMMENDED to use all non-private IP addresses as SDAs.

   A different SDA must be chosen, should the IP address of the data
   sender be unknown.  This can have multiple reasons: The application
   level signaling protocol cannot determine any data sender IP address
   at this point of time or the data receiver is server behind a NAT,
   i.e., accepting inbound packets from any host.  In this case, the
   NATFW NSLP can be instructed to use the public IP address of an
   application server or any other node.  Choosing the SDA in this case
   is out of the scope of the NATFW NSLP and depends on the
   application's choice.  The local network can provide a network-SDA,
   i.e., a SDA which is only meaningful to the local network.  This will
   ensure that GIST packets with destination-address set to this
   network-SDA are going to be routed to a edge-NAT or edge-firewall.









Stiemerling, et al.     Expires January 10, 2008               [Page 80]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Appendix B.  Applicability Statement on Data Receivers behind Firewalls

   Section 3.7.2 describes how data receivers behind middleboxes can
   instruct inbound firewalls/NATs to forward NATFW NSLP signaling
   towards them.  Finding an inbound edge-NAT in address environment
   with NAT'ed addresses is quite easy.  It is only required to find
   some edge-NAT, as the data traffic will be route-pinned to the NAT,
   which is done with the LE-MRM.  Locating the appropriate edge-
   firewall with the PC-MRM, sent inbound is difficult.  For cases with
   a single, symmetric route from the Internet to the data receiver, it
   is quite easy; simply follow the default route in the inbound
   direction.


                             +------+                  Data Flow
                     +-------| EFW1 +----------+     <===========
                     |       +------+       ,--+--.
                  +--+--+                  /       \
          NI+-----| FW1 |                 (Internet )----NR+/NI/DS
          NR      +--+--+                  \       /
                     |       +------+       `--+--'
                     +-------| EFW2 +----------+
                             +------+

           ~~~~~~~~~~~~~~~~~~~~~>
             Signaling Flow



   Figure 34: Data receiver behind multiple, parallel located firewalls

   When a data receiver, and thus NR, is located in a network site that
   is multihomed with several independently firewalled connections to
   the public Internet (as shown in Figure 34), the specific firewall
   through which the data traffic will be routed has to be ascertained.
   NATFW NSLP signaling messages sent from the NI+/NR during the EXT
   message exchange towards the NR+ must be routed by the NTLP to the
   edge-firewall that will be passed by the data traffic as well.  The
   NTLP would need to be aware about the routing within the Internet to
   determine the path between DS and DR.  Out of this, the NTLP could
   determine which of the edge-firewalls, either EFW1 or EFW2, must be
   selected to forward the NATFW NSLP signaling.  Signaling to the wrong
   edge-firewall, as shown in Figure 34, would install the NATFW NSLP
   policy rules at the wrong device.  This causes either a blocked data
   flow (when the policy rule is 'allow') or an ongoing attack (when the
   policy rule is 'deny').  Requiring the NTLP to know all about the
   routing within the Internet is definitely a tough challenge and
   usually not possible.  In such described case, the NTLP must



Stiemerling, et al.     Expires January 10, 2008               [Page 81]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   basically give up and return an error to the NSLP level, indicating
   that the next hop discovery is not possible.

















































Stiemerling, et al.     Expires January 10, 2008               [Page 82]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Appendix C.  Firewall and NAT Resources

   This section gives some examples on how NATFW NSLP policy rules could
   be mapped to real firewall or NAT resources.  The firewall rules and
   NAT bindings are described in a natural way, i.e., in a way one will
   find it in common implementation.

C.1.  Wildcarding of Policy Rules

   The policy rule/MRI to be installed can be wildcarded to some degree.
   Wildcarding applies to IP address, transport layer port numbers, and
   the IP payload (or next header in IPv6).  Processing of wildcarding
   splits into the NTLP and the NATFW NSLP layer.  The processing at the
   NTLP layer is independent of the NSLP layer processing and per layer
   constraints apply.  For wildcarding in the NTLP see Section 5.8 of
   [2].

   Wildcarding at the NATFW NSLP level is always a node local policy
   decision.  A signaling message carrying a wildcarded MRI (and thus
   policy rule) arriving at an NSLP node can be rejected if the local
   policy does not allow the request.  For instance, a MRI with IP
   addresses set (not wildcarded), transport protocol TCP, and TCP port
   numbers completely wildcarded.  Now the local policy allows only
   requests for TCP with all ports set and not wildcarded.  The request
   is going to be rejected.

C.2.  Mapping to Firewall Rules

   This section describes how a NSLP policy rule signaled with a CREATE
   message is mapped to a firewall rule.  The MRI is set as follows:

   o  network-layer-version=IPv4

   o  source-address=192.0.2.100, prefix-length=32

   o  destination-address=192.0.50.5, prefix-length=32

   o  IP-protocol=UDP

   o  L4-source-port=34543, L4-destination-port=23198

   The NATFW_EFI object is set to action=allow and sub_ports=0.

   The resulting policy rule (firewall rule) to be installed might look
   like: allow udp from 192.0.2.100 port=34543 to 192.0.50.5 port=23198






Stiemerling, et al.     Expires January 10, 2008               [Page 83]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


C.3.  Mapping to NAT Bindings

   This section describes how a NSLP policy rule signaled with a EXT
   message is mapped to a NAT binding.  It is assumed that the EXT
   message is sent by a NI+ being located behind a NAT and does contain
   a NATFW_DTINFO object.  The MRI is set following using the signaling
   destination address, since the IP address of the real data sender is
   not known:

   o  network-layer-version=IPv4

   o  source-address= 192.168.5.100

   o  destination-address=SDA

   o  IP-protocol=UDP

   The NATFW_EFI object is set to action=allow and sub_ports=0.  The
   NATFW_DTINFO object contains these parameters:

   o  P=1

   o  dest prefix=0

   o  protocol=UDP

   o  dst port number = 20230, src port number=0

   o  src IP=0.0.0.0

   The edge-NAT allocates the external IP 192.0.2.79 and port 45000.

   The resulting policy rule (NAT binding) to be installed could look
   like: translate from any to 192.0.2.79 port=45000 to 192.168.5.100
   port=20230

C.4.  NSLP Handling of Twice-NAT

   The dynamic configuration of twice-NATs requires application level
   support, as stated in Section 2.5.  The NATFW NSLP cannot be used for
   configuring twice-NATs if application level support is needed.
   Assuming application level support performing the configuration of
   the twice-NAT and the NATFW NSLP being installed at this devices, the
   NATFW NSLP must be able to traverse it.  The NSLP is probably able to
   traverse the twice-NAT, as any other data traffic, but the flow
   information stored in the NTLP's MRI will be invalidated through the
   translation of source and destination address.  The NATFW NSLP
   implementation on the twice-NAT MUST intercept NATFW NSLP and NTLP



Stiemerling, et al.     Expires January 10, 2008               [Page 84]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


   signaling messages as any other NATFW NSLP node does.  For the given
   signaling flow, the NATFW NSLP node MUST look up the corresponding IP
   address translation and modify the NTLP/NSLP signaling accordingly.
   The modification results in an updated MRI with respect to the source
   and destination IP addresses.














































Stiemerling, et al.     Expires January 10, 2008               [Page 85]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Appendix D.  Assigned Numbers for Testing

   NOTE: This section MUST be removed before publication.

   This section defines temporarily used values of the NATFW NSLP for
   testing the different implementations.

   Values for the NATFW NSLP message types:

   o  CREATE: 0x01

   o  EXT: 0x02

   o  RESPONSE: 0x03

   o  NOTIFY: 0x04

   Values for the NSLP object types

   o  NATFW_LT: 0x00F1

   o  NATFW_EXT_IP: 0x00F2

   o  NATFW_EFI: 0x00F3

   o  NATFW_INFO: 0x00F4

   o  NATFW_NONCE: 0x00F5

   o  NATFW_MSN: 0x00F6

   o  NATFW_DTINFO: 0x00F7

   o  NATFW_ICMP_TYPES: 0x00F9

   1345















Stiemerling, et al.     Expires January 10, 2008               [Page 86]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Authors' Addresses

   Martin Stiemerling
   NEC Europe Ltd. and University of Goettingen
   Kurfuersten-Anlage 36
   Heidelberg  69115
   Germany

   Phone: +49 (0) 6221 4342 113
   Email: stiemerling@netlab.nec.de
   URI:   http://www.stiemerling.org


   Hannes Tschofenig
   Nokia Siemens Networks
   Otto-Hahn-Ring 6
   Munich  81739
   Germany

   Phone:
   Email: Hannes.Tschofenig@nsn.com
   URI:   http://www.tschofenig.com


   Cedric Aoun
   Paris
   France

   Email: cedric@caoun.net


   Elwyn Davies
   Folly Consulting
   Soham
   UK

   Phone: +44 7889 488 335
   Email: elwynd@dial.pipex.com













Stiemerling, et al.     Expires January 10, 2008               [Page 87]


Internet-Draft              NAT/FW NSIS NSLP                   July 2007


Full Copyright Statement

   Copyright (C) The IETF Trust (2007).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.


Acknowledgment

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).





Stiemerling, et al.     Expires January 10, 2008               [Page 88]