Network Working Group M. Brunner (Editor)
Internet Draft NEC
Category: Informational March 2003
Requirements for Signaling Protocols
<draft-ietf-nsis-req-07.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract
This document defines requirements for signaling across different
network environments, such as across administrative and/or
technology domains. Signaling is mainly considered for Quality of
Service such as The Resource Reservation Protocol, however in recent
years several other applications of signaling have been defined such
as signaling for label distribution in Multiprotocol Label Switching
or signaling to middleboxes. To achieve wide applicability of the
requirements, the starting point is a diverse set of scenarios/use
cases concerning various types of networks and application
interactions. This document presents the assumptions before listing
the requirements. The requirements are grouped according to areas
such as architecture and design goals, signaling flows, layering,
performance, flexibility, security, and mobility.
Brunner (Editor) Informational [Page 1]
Requirements for Signaling Protocols March 2003
Table of Contents
Status of this Memo................................................1
Abstract...........................................................1
Table of Contents..................................................2
1 Introduction.....................................................2
1.1. Keywords....................................................3
2 Terminology......................................................3
3 Problem Statement and Scope......................................4
4 Assumptions and Exclusions.......................................5
4.1 Assumptions and Non-Assumptions................................5
4.2 Exclusions.....................................................6
5 Requirements.....................................................7
5.1 Architecture and Design Goals..................................8
5.2 Signaling Flows................................................9
5.3 Messaging.....................................................10
5.4 Control Information...........................................12
5.5 Performance...................................................13
5.6 Flexibility...................................................15
5.7 Security......................................................16
5.8 Mobility......................................................18
5.9 Interworking with other protocols and techniques..............18
5.10 Operational..................................................19
6 Security Considerations.........................................19
7 References......................................................19
7.1 Normative References..........................................19
7.2 Non-Normative References......................................20
8 Acknowledgments.................................................20
9 Author's Addresses..............................................20
10 Appendix: Scenarios/Use cases..................................21
10.1 Terminal Mobility............................................21
10.2 3G Wireless Networks.........................................23
10.3 An example scenario for 3G wireless networks.................24
10.4 Wired part of wireless network...............................26
10.5 Session Mobility.............................................27
10.6 QoS s/negotiation from access to core network................28
10.7 QoS /negotiation over administrative boundaries..............28
10.8 QoS signaling between PSTN gateways and backbone routers.....29
10.9 PSTN trunking gateway........................................30
10.10 Application request end-to-end QoS path from the network....32
1 Introduction
This document defines requirements for signaling across different
network environments. It does not list any problems of existing
signaling protocols such as [RSVP].
In order to derive requirements for signaling it is necessary to
first have an idea of the scope within which they are applicable.
Therefore, we list use cases and scenarios where an NSIS protocol
could be applied. The scenarios are used to help derive requirements
and to test the requirements against use cases.
Brunner (Editor) Informational [Page 2]
Requirements for Signaling Protocols March 2003
The requirements listed are independent of any application. However,
resource reservation and QoS related issues are used as example
within the text. However, QoS is not the only field where signaling
is used in the Internet. Others might be the use for middlebox
communication [RFC3234].
There are several areas related to networking aspects which are
incomplete, for example, interaction with host and site multi-
homing, use of anycast services, and so on. These issues should be
considered in any future analysis work.
1.1. Keywords
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in RFC 2119
[KEYWORDS].
2 Terminology
We list the most often used terms in the document. However, they
cannot be made precise without a more complete architectural model,
and they are not meant to prescribe any solution in the document.
Where applicable, they will be defined in protocol documents.
NSIS Entity (NE): The function within a node, which implements an
NSIS protocol. In the case of path-coupled signaling, the NE will
always be on the data path.
NSIS Forwarder (NF): NSIS Entity between a NI and NR, which may
interact with local state management functions in the network. It
also propagates NSIS signaling further through the network.
NSIS Initiator (NI): NSIS Entity that starts NSIS signaling to set
up or manipulate network state.
NSIS Responder (NR): NSIS Entity that terminates NSIS signaling and
can optionally interact with applications as well.
Flow: A traffic stream (sequence of IP packets between two end
systems) for which a specific packet level treatment is provided.
The flow can be unicast (uni- or bi-directional) or multicast. For
multicast, a flow can diverge into multiple flows as it propagates
toward the receiver. For multi-sender multicast, a flow can also
diverge when viewed in the reverse direction (toward the senders).
Data Path: The route across the networks taken by a flow or
aggregate, i.e. which domains/subdomains it passes through and the
egress/ingress points for each.
Signaling Path: The route across the networks taken by a signaling
flow or aggregate, i.e. which domains/subdomains it passes through
and the egress/ingress points for each.
Brunner (Editor) Informational [Page 3]
Requirements for Signaling Protocols March 2003
Path-coupled signaling: A mode of signaling where the signaling
messages follow a path that is tied to the data packets. Signaling
messages are routed only through nodes (NEs) that are in the data
path.
Path-decoupled signaling: Signaling with independent data and
signaling paths. Signaling messages are routed to nodes (NEs) which
are not assumed to be on the data path, but which are (presumably)
aware of it. Signaling messages will always be directly addressed to
the neighbor NE, and the NI/NR may have no relation at all with the
ultimate data sender or receiver.
Service: A generic something provided by one entity and consumed by
another. It can be constructed by allocating resources. The network
can provide it to users or a network node can provide it to packets.
3 Problem Statement and Scope
We provide in the following a preliminary architectural picture as a
basis for discussion. We will refer to it in the following
requirement sections.
Note that this model is intended not to constrain the technical
approach taken subsequently, simply to allow concrete phrasing of
requirements (e.g. requirements about placement of the NSIS
Initiator.)
Roughly, the scope of NSIS is assumed to be the interaction between
the NSIS Initiator and NSIS Forwarder(s), and NSIS Responder
including a protocol to carry the information, and the
syntax/semantics of the information that is exchanged. Further
statements on assumptions/exclusions are given in the next Section.
The main elements are:
1. Something that starts the request for state to be set up in the
network, the NSIS Initiator.
This might be in the end system or within some other part of the
network. The distinguishing feature of the NSIS Initiator is that it
acts on triggers coming (directly or indirectly) from the higher
layers in the end systems. It needs to map the services requested by
them, and also provides feedback information to the higher layers,
which might be used by transport layer algorithms or adaptive
applications.
2. Something that assists in managing state further along the
signaling path, the NSIS Forwarder.
The NSIS Forwarder does not interact with higher layers, but
interacts with the NSIS Initiator, NSIS Responder, and possibly one
or more NSIS Forwarders on the signaling path, edge-to-edge or end-
to-end.
Brunner (Editor) Informational [Page 4]
Requirements for Signaling Protocols March 2003
3. Something that terminates the signaling path, the NSIS Responder.
The NSIS responder might be in an end-system or within other
equipment. The distinguishing feature of the NSIS Initiator is that
it responds to requests at the end of a signaling path.
4. The signaling path traverses an underlying network covering one
or more IP hops. The underlying network might use locally different
technology. For instance, QoS technology has to be provisioned
appropriately for the service requested. In the QoS example, an NSIS
Forwarder maps service-specific information to technology-related
QoS parameters and receives indications about success or failure in
response.
5. We can see the network at the level of domains/subdomains rather
than individual routers (except in the special case that the domain
contains one link). Domains are assumed to be administrative
entities, so security requirements apply to the signaling between
them.
4 Assumptions and Exclusions
4.1 Assumptions and Non-Assumptions
1. The NSIS signaling could run end to end, end-to-edge, or edge-to-
edge, or network-to-network ((between providers), depending on what
point in the network acts as NSIS initiator, and how far towards the
other end of the network the signaling propagates. In general, we
could expect NSIS Forwarders to become more 'dense' towards the
edges of the network, but this is not a requirement. For example, in
the case of QoS, an over-provisioned domain might contain no NSIS
Forwarders at all (and be NSIS transparent); at the other extreme,
NSIS Forwarders might be placed at every router. In the latter case,
QoS provisioning can be carried out in a local implementation-
dependent way without further signaling, whereas in the case of
remote NSIS Forwarders, a protocol might be needed to control the
routers along the path. This protocol is then independent of the
end-to-end NSIS signaling.
2. We do not consider 'pure' end-to-end signaling that is not
interpreted anywhere within the network. Such signaling is a higher-
layer issue and IETF protocols such as SIP etc. can be used.
3. Where the signaling does cover several domains, we do not exclude
that different signaling protocols are used in each domain. We only
place requirements on the universality of the control information
that is being transported. (The goals here would be to allow the use
of signaling protocols, which are matched to the characteristics of
the portion of the network being traversed.) Note that the outcome
of NSIS work might result in various flavors of the same protocol.
4. We assume that the service definitions a NSIS Initiator can ask
for are known in advance of the signaling protocol running. For
instance in the QoS example, the service definition includes QoS
Brunner (Editor) Informational [Page 5]
Requirements for Signaling Protocols March 2003
parameters, lifetime of QoS guarantee etc., or any other service-
specific parameters.
There are many ways service requesters get to know about available
services. There might be standardized services, the definition can
be negotiated together with a contract, the service definition is
published in some on-line directory (e.g., at a Web page), and so
on.
5. We assume that there are means for the discovery of NSIS entities
in order to know the signaling peers (solutions include static
configuration, automatically discovered, or implicitly runs over the
right nodes along the data path, etc.) The discovery of the NSIS
entities has security implications that need to be addressed
properly. For some security mechanisms (i.e. Kerberos, pre-shared
secret) it is required to know the identity of the other entity.
Hence the discovery mechanism may provide means to learn this
identity, which is then later used to retrieve the required keys and
parameters.
6. NSIS assumes layer 3 routing and the determination of next data
node selection is not done by NSIS.
4.2 Exclusions
1. Development of specific mechanisms and algorithms for application
and transport layer adaptation are not considered, nor are the
protocols that would support it.
2. Specific mechanisms (APIs and so on) for interaction between
transport/applications and the network layer are not considered,
except to clarify the requirements on the negotiation capabilities
and information semantics that would be needed of the signaling
protocol.
3. Specific mechanisms and protocols for provisioning or other
network control functions within a domain/subdomain are not
considered. The goal is to reuse existing functions and protocols
unchanged. However, NSIS itself can be used for signaling within a
domain/subdomain.
For instance in the QoS example, it means that the setting of QoS
mechanisms in a domain is out of scope, but if we have a tunnel,
NSIS could also be used for tunnel setup with QoS guarantees. It
should be possible to exploit these mechanisms optimally within the
end-to-end context. Consideration of how to do this might generate
new requirements for NSIS however. For example, the information
needed by a NSIS Forwarder to manage a radio subnetwork needs to be
provided by the NSIS solution.
4. Specific mechanisms (APIs and so on) for interaction between the
network layer and underlying provisioning mechanisms are not
considered.
Brunner (Editor) Informational [Page 6]
Requirements for Signaling Protocols March 2003
5. Interaction with resource management or other internal state
management capabilities is not considered. Standard protocols might
be used for this. This may imply requirements for the sort of
information that should be exchanged between the NSIS entities.
6. Security implications related to multicasting are outside the
scope of the signaling protocol.
7. Service definitions and in particular QoS services and classes
are out of scope. Together with the service definition any
definition of service specific parameters are not considered in this
document. Only the base NSIS signaling protocol for transporting the
service information are addressed.
8. Similarly, specific methods, protocols, and ways to express
service information in the Application/Session level are not
considered (e.g., SDP, SIP, RTSP, etc.).
9. The specification of any extensions needed to signal information
via application level protocols (e.g. SDP), and the mapping on NSIS
information are considered outside of the scope of NSIS working
group, as this work is in the direct scope of other IETF working
groups (e.g. MMUSIC).
10. Handoff decision and trigger sources: An NSIS protocol is not
used to trigger handoffs in mobile IP, nor is it used to decide
whether to handoff or not. As soon as or in some situation even
before a handoff happened, an NSIS protocol might be used for
signaling for the particular service again. The basic underlying
assumption is that the route comes first (defining the path) and the
signaling comes after it (following the path). This doesn't prevent
a signaling application at some node interacting with something that
modifies the path, but the requirement is then just for NSIS to live
with that possibility. However, NSIS must interwork with several
protocols for mobility management.
11. Service monitoring is out of scope. It is heavily dependent on
the type of the application and or transport service, and in what
scenario it is used.
5 Requirements
This section defines more detailed requirements for a signaling
solution, respecting the framework, scoping assumptions, and
terminology considered earlier. The requirements are in subsections,
grouped roughly according to general technical aspects: architecture
and design goals, topology issues, parameters, performance,
security, information, and flexibility.
Two general (and potentially contradictory) goals for the solution
are that it should be applicable in a very wide range of scenarios,
and at the same time lightweight in implementation complexity and
resource consumption requirements in NSIS Entities. One approach to
this is that the solution could deal with certain requirements via
Brunner (Editor) Informational [Page 7]
Requirements for Signaling Protocols March 2003
modular components or capabilities, which are optional to implement
or use in individual nodes.
In order to prioritize the various requirements we informally define
different 'parts of the network'. In the different parts of the
network a particular requirement might have a different priority.
The parts of the networks we differentiate are the host-to-first
router, the access network, and the core network. The host to first
router part includes all the layer 2 technologies to access to the
Internet. In many cases, there is an application and/or user running
on the host initiating signaling. The access network can be
characterized by low capacity links, medium speed IP processing
capabilities, and it might consist of a complete layer 2 network as
well. The core network characteristics include high-speed forwarding
capacities and inter-domain issues. These divisions between network
types are not strict and do not appear in all networks, but where
they do exist they may influence signaling requirements and will be
highlighted as necessary.
5.1 Architecture and Design Goals
This section contains requirements related to desirable overall
characteristics of a solution, e.g. enabling flexibility, or
independence of parts of the framework.
5.1.1 NSIS SHOULD provide availability information on request
NSIS SHOULD provide a mechanism to check whether state to be setup
is available without setting it up. For the resource reservation
example this translates into checking resource availability without
performing resource reservation. In some scenarios, e.g., the mobile
terminal scenario, it is required to query, whether resources are
available, without performing a reservation on the resource.
5.1.2 NSIS MUST be designed modularly
A modular design allows for more lightweight implementations, if
fewer features are needed. Mutually exclusive solutions are
supported. Examples for modularity:
- Work over any kind of network (narrowband versus broadband, error-
prone versus reliable, ...). This implies low bandwidth signaling,
and elimination of redundant information MUST be supported if
necessary.
- State setup for uni- and bi-directional flows is possible
- Extensible in the future with different add-ons for certain
environments or scenarios
- Protocol layering, where appropriate. This means NSIS MUST provide
a base protocol, which can be adapted to different environments.
Brunner (Editor) Informational [Page 8]
Requirements for Signaling Protocols March 2003
5.1.3 NSIS MUST decouple protocol and information
The signaling protocol MUST be clearly separated from the control
information being transported. This provides for the independent
development of these two aspects of the solution, and allows for
this control information to be carried within other protocols,
including application layer ones, existing ones or those being
developed in the future. The flexibility gained in the transport of
information allows for the applicability of the same protocol in
various scenarios.
However, note that the information carried needs to be standardized;
otherwise interoperability is difficult to achieve.
5.1.4 NSIS MUST support independence of signaling and network control
paradigm
The signaling MUST be independent of the paradigm and mechanism of
network control. E.g., in the case of signaling for QoS, the
independence of the signaling protocol from the QoS provisioning
allows for using the NSIS protocol together with various QoS
technologies in various scenarios.
5.1.5 NSIS SHOULD be able to carry opaque objects
NSIS SHOULD be able to pass around opaque objects, which are
interpreted only by some NSIS-capable nodes.
5.2 Signaling Flows
This section contains requirements related to the possible signaling
flows that should be supported, e.g. over what parts of the flow
path, between what entities (end-systems, routers, middle boxes,
management systems), in which direction.
5.2.1 The placement of NSIS Initiator, Forwarder, and Responder
anywhere in the network MUST be allowed
The protocol MUST work in various scenarios such as host-to-network-
to-host, edge-to-edge, (e.g., just within one provider's domain),
user-to-network (from end system into the network, ending, e.g., at
the entry to the network and vice versa), and network-to-network
(e.g., between providers).
Placing the NSIS Forwarder and NSIS Initiator functions at different
locations allows for various scenarios to work with the same
protocol.
5.2.2 NSIS MUST support path-coupled and SHOULD NOT exclude path-
decoupled signaling.
The path-coupled signaling mode MUST be supported. NSIS signaling
messages are routed only through nodes (NEs) that are in the data
path.
Brunner (Editor) Informational [Page 9]
Requirements for Signaling Protocols March 2003
However, there is a set of scenarios, where signaling is not on the
data path. Therefore, NSIS SHOULD NOT exclude the path-decoupled
signaling mode, where signaling messages are routed to nodes (NEs),
which are not assumed to be on the data path, but which are aware of
it.
5.2.3 Concealment of topology and technology information SHOULD be
possible
The NSIS protocol SHOULD allow for hiding the internal structure of
a NSIS domain from end-nodes and from other networks. Hence an
adversary should not be able to learn the internal structure of a
network with the help of the signaling protocol.
In various scenarios, topology information should be hidden for
various reasons. From a business point of view, some administrations
don't want to reveal the topology and technology used.
5.2.4 Transparent signaling through networks SHOULD be possible
It SHOULD be possible that the signaling for some flows traverses
path segments transparently, i.e., without interpretation at NSIS
Forwarders within the network. An example would be a subdomain
within a core network, which only interpreted signaling for
aggregates established at the domain edge, with the signaling for
individual flows passing transparently through it.
In other words, NSIS SHOULD work in hierarchical scenarios, where
big pipes/trunks are setup using NSIS signaling, but also flows
which run within that big pipe/trunk are setup using NSIS.
5.3 Messaging
5.3.1 Explicit erasure of state MUST be possible
When state along a path is no longer necessary, e.g., because the
application terminates, or because a mobile host experienced a hand-
off, it MUST be possible to erase the state explicitly.
5.3.2 Automatic release of state after failure SHOULD be possible
When the NSIS Initiator goes down, the state it requested in the
network SHOULD be released, since it will no longer be necessary.
After detection of a failure in the network, any NSIS
Forwarder/Initiator MUST be able to release state it is involved in.
For example, this may require signaling of the "Release after
Failure" message upstream as well as downstream, or soft state
timing out.
The goal is to prevent stale state within the network and adds
robustness to the operation of NSIS. So in other words, an NSIS
Brunner (Editor) Informational [Page 10]
Requirements for Signaling Protocols March 2003
signaling protocol or mechanisms MUST provide means for an NSIS
entity to discover and remove local stale state.
Note that this might need to work together with a notification
mechanism.
5.3.3 NSIS SHOULD allow for sending notifications upstream
NSIS Forwarders SHOULD notify the NSIS Initiator or any other NSIS
Forwarder upstream, if there is a state change inside the network.
There are various types of network changes for instance among them:
Recoverable errors: the network nodes can locally repair this type
error. The network nodes do not have to notify the users of the
error immediately. This is a condition when the danger of
degradation (or actual short term degradation) of the provided
service was overcome by the network (NSIS Forwarder) itself.
Unrecoverable errors: the network nodes cannot handle this type of
error, and have to notify the users as soon as possible.
Service degradation: In case the service cannot be provided
completely but only partially.
Repair indication: If an error occurred and it has been fixed, this
triggers the sending of a notification.
Service upgrade available: If a previously requested better service
becomes available.
The content of the notification is very service specific, but it is
must at least carry type information. Additionally, it may carry the
location of the state change.
The notifications may or may not be in response to a NSIS message.
This means an NSIS entity has to be able to handle notifications at
any time.
Note however, that there are a number of security consideration
needs to be solved with notification, even more important if the
notification is sent without prior request (asynchronously). The
problem basically is, that everybody could send notifications to any
NSIS entity and the NSIS entity most likely reacts on the
notification. For example, if it gets an error notification it might
erase state, even if everything is ok. So the notification might
depend on security associations between the sender of the
notification and its receiver. If a hop-by-hop security mechanism is
chosen, this implies also that notifications need to be sent on the
reverse path.
.3.4 Establishment and refusal to set up state MUST be notified.
An NR MUST acknowledge establishment of state on behalf of the NI
requesting establishment of that state. A refusal to set up state
Brunner (Editor) Informational [Page 11]
Requirements for Signaling Protocols March 2003
MUST be replied with a negative acknowledgement by the NE refusing
to set up state. It MUST be sent to the NI. Depending on the
signaling application the (positive or negative) notifications may
have to pass through further NEs upstream. Information on the reason
of the refusal to set up state MAY be made available. For example,
in the resource reservation example, together with a negative
answer, the amount of resources available might also be returned.
5.3.5 NSIS MUST allow for local information exchange
The signaling protocol MUST be able to exchange local information
between NSIS Forwarders located within one single administrative
domain. The local information exchange is performed by a number of
separate messages not belonging to an end-to-end signaling process.
Local information might, for example, be IP addresses , notification
of successful or erroneous processing of signaling messages, or
other conditions.
In some cases, the NSIS signaling protocol MAY carry identification
of the NSIS Forwarders located at the boundaries of a domain.
However, the identification of edge should not be visible to the end
host (NSIS Initiator) and only applies within one administrative
domain.
5.4 Control Information
This section contains requirements related to the control
information that needs to be exchanged.
5.4.1 Mutability information on parameters SHOULD be possible
It SHOULD be possible for the NSIS initiator to control the
mutability of the signaled information. This prevents them from
being changed in a non-recoverable way. The NSIS initiator SHOULD be
able to control what is requested end to end, without the request
being gradually mutated as it passes through a sequence of domains.
This implies that in case of changes made on the parameters, the
original requested ones must still be available.
Note that we do not require anything about particular parameters
being changed.
Additionally, note that the provider of the particular requested
services can still influence the provisioning but in the signaling
message the request should stay the same.
5.4.2 It SHOULD be possible to add and remove local domain information
It SHOULD be possible to add and remove local scope elements.
Compared to Requirement 5.3.5 this requirement does use the normal
signaling process and message exchange for transporting local
information. For example, at the entrance to a domain domain-
specific information is added, which is used in this domain only,
and the information is removed again when a signaling message leaves
Brunner (Editor) Informational [Page 12]
Requirements for Signaling Protocols March 2003
the domain. The motivation is in the economy of re-using the
protocol for domain internal signaling of various information
pieces. Where additional information is needed within a particular
domain, it should be possible to carry this at the same time as the
end-to-end information.
5.4.3 State MUST be addressed independent of flow identification
Addressing or identifying state MUST be independent of the flow
identifier (flow end-points, topological addresses). Various
scenarios in the mobility area require this independence because
flows resulting from handoff might have changed end-points etc. but
still have the same service requirement. Also several proxy-based
signaling methods profit from such independence.
5.4.4 Modification of already established state SHOULD be seamless
In many case, the established state needs to be updated (in QoS
example upgrade or downgrade of resource usage). This SHOULD happen
seamlessly without service interruption. At least the signaling
protocol should allow for it, even if some data path elements might
not be capable of doing so.
5.4.5 Grouping of signaling for several micro-flows MAY be provided
NSIS MAY group signaling information for several micro-flow into one
signaling message. The goal of this is the optimization in terms of
setup delay, which can happen in parallel. This helps applications
requesting several flows at once. Also potential refreshes (in case
of a soft state solution) might profit from grouping.
However, the network needs not know that a relationship between the
grouped flows exists. There MUST NOT be any transactional semantic
associated with the grouping. It is only meant for optimization
purposes.
5.5 Performance
This section discusses performance requirements and evaluation
criteria and the way in which these could and should be traded off
against each other in various parts of the solution.
Scalability is always an important requirement for signaling
protocols. However, the type of scalability and its importance
varies from one scenario to another.
Note that many of the performance issues are heavily dependent on
the scenario assumed and are normally a trade-off between speed,
reliability, complexity, and scalability. The trade-off varies in
different parts of the network. For example, in radio access
networks low bandwidth consumption will outweigh the low latency
requirement, while in core networks it may be reverse.
Brunner (Editor) Informational [Page 13]
Requirements for Signaling Protocols March 2003
5.5.1 Scalability
NSIS MUST be scalable in the number of messages received by a
signaling communication partner (NSIS Initiator, NSIS Forwarder, and
NSIS Responder). The major concern lies in the core of the network,
where large numbers of messages arrive.
It MUST be scalable in number of hand-offs in mobile environments.
This mainly applies in access networks, because the core is
transparent to mobility in most cases.
It MUST be scalable in the number of interactions for setting up a
state. This applies for end-systems setting up several states. Some
servers might be expected to setup a large number of states.
Scalability in the amount of state per entity MUST be achieved for
NSIS Forwarders in the core of the network.
Scalability in CPU usage MUST be achieved on end terminals and
intermediate nodes in case of many state setup processes at the same
time.
5.5.2 NSIS SHOULD allow for low latency in setup
NSIS SHOULD allow for low latency setup of states. This is only
needed in scenarios, where state setups are required on a short time
scale (e.g. handover in mobile environments), or where human
interaction is immediately concerned (e.g., voice communication
setup delay).
5.5.3 NSIS MUST allow for low bandwidth consumption for the signaling
protocol
NSIS MUST allow for low bandwidth consumption in certain access
networks. Again only small sets of scenarios call for low bandwidth,
mainly those where wireless links are involved.
5.5.4 NSIS SHOULD allow to constrain load on devices
The NSIS architecture SHOULD give the ability to constrain the load
(CPU load, memory space, signaling bandwidth consumption and
signaling intensity) on devices where it is needed. One of the
reasons is that the protocol handling should have a minimal impact
on interior (core) nodes.
This can be achieved by many different methods. Examples include
message aggregation, header compression, or minimizing
functionality. The framework may choose any method as long as the
requirement is met.
5.5.5 NSIS SHOULD target the highest possible network utilization
This requirement applies specifically to QoS signaling.
Brunner (Editor) Informational [Page 14]
Requirements for Signaling Protocols March 2003
There are networking environments that require high network
utilization for various reasons, and the signaling protocol SHOULD
to its best ability support high resource utilization while
maintaining appropriate service quality.
In networks where resources are very expensive (as is the case for
many wireless networks), efficient network utilization for signaling
traffic is of critical financial importance. On the other hand
there are other parts of the network where high utilization is not
required.
5.6 Flexibility
This section lists the various ways the protocol can flexibly be
employed.
5.6.1 Flow aggregation
NSIS MUST allow for flow aggregation, including the capability to
select and change the level of aggregation.
5.6.2 Flexibility in the placement of the NSIS Initiator/Responder
NSIS MUST be flexible in placing an NSIS Initiator and NSIS
Responder. The NSIS Initiator might be located at the sending or the
receiving side of a data stream, and the NSIS Responder naturally on
the other side.
Also network-initiated signaling and termination MUST be allowed in
various scenarios such as PSTN gateways, some VPNs, and mobility.
This means the NSIS Initiator and NSIS Responder might not be at the
end points of the data stream.
5.6.3 Flexibility in the initiation of state change
The NSIS Initiator or the NSIS Responder SHOULD be able to initiate
a change of state. In the example of resource reservation this is
often referred to as resource re-negotiation. It can happen due to
various reasons, such as local resource shortage (CPU, memory on
end-system) or a user changed application preference/profiles.
5.6.4 SHOULD support network-initiated state change
NSIS SHOULD support network-initiated state change. In the QoS
example, this is used in cases, where the network is not able to
further guarantee resources and wants to e.g. downgrade a resource
reservation.
5.6.5 Uni / bi-directional state setup
Both unidirectional as well as bi-direction state setup SHOULD be
possible. With bi-directional state setup we mean that the state for
Brunner (Editor) Informational [Page 15]
Requirements for Signaling Protocols March 2003
bi-directional data flows is setup. The bi-directional data flows
have the same end-points, but the path in the two directions does
not need to be the same.
The goal of a bi-directional state setup is mainly an optimization
in terms of setup delay. There is no requirements on constrains such
as use of the same data path etc.
5.7 Security
This section discusses security-related requirements. The NSIS
protocol MUST provide means for security, but it MUST be allowed
that nodes implementing NSIS signaling do not need use the security
means.
5.7.1 Authentication of signaling requests
A signaling protocol MUST make provision for enabling various
entities to be authenticated against each other using strong
authentication mechanisms. The term strong authentication points to
the fact that weak plain-text password mechanisms must not be used
for authentication.
5.7.2 Request Authorization
The signaling protocol MUST provide means to authorize state setup
requests. This requirement demands a hook to interact with a policy
entity to request authorization data. This allows an authenticated
entity to be associated with authorization data and to verify the
request. Authorization prevents state setup by unauthorized entities,
setups violating policies, and theft of service. Additionally it
limits denial of service attacks against parts of the network or the
entire network caused by unrestricted state setups. Additionally it
might be helpful to provide some means to inform other protocols of
participating nodes within the same administrative domain about a
previous successful authorization event.
5.7.3 Integrity protection
The signaling protocol MUST provide means to protect the message
payloads against modifications. Integrity protection prevents an
adversary from modifying parts of the signaling message and from
mounting denial of service or theft of service type of attacks
against network elements participating in the protocol execution.
5.7.4 Replay protection
To prevent replay of previous signaling messages the signaling
protocol MUST provide means to detect old i.e. already transmitted
signaling messages. A solution must cover issues of synchronization
problems in the case of a restart or a crash of a participating
network element.
Brunner (Editor) Informational [Page 16]
Requirements for Signaling Protocols March 2003
5.7.5 Hop-by-hop security
Hop-by-Hop security SHOULD be supported. It is a well known and
proven concept in Quality-of-Service and other signaling protocols
that allows intermediate nodes that actively participate in the
protocol to modify the messages as it is required by processing
rules. Note that this requirement does not exclude end-to-end or
network-to-network security of a signaling message. End-to-end
security between the initiator and the responder may be used to
provide protection of non-mutable data fields. Network-to-network
security refers to the protection of messages over various hops but
not in an end-to-end manner i.e. protected over a particular network.
5.7.6 Identity confidentiality and network topology hiding
Identity confidentiality SHOULD be supported. It enables privacy and
avoids profiling of entities by adversary eavesdropping the signaling
traffic along the path. The identity used in the process of
authentication may also be hidden to a limited extent from a network
to which the initiator is attached. However the identity MUST provide
enough information for the nodes in the access network to collect
accounting data.
Network topology hiding MAY be supported to prevent entities along
the path to learn the topology of a network. Supporting this property
might conflict with a diagnostic capability.
5.7.7 Denial-of-service attacks
A signaling protocol SHOULD provide prevention of Denial-of-service
attacks. To effectively prevent denial-of-service attacks it is
necessary that the used security and protocol mechanisms MUST have
low computational complexity to verify a state setup request prior to
authenticating the requesting entity. Additionally the signaling
protocol and the used security mechanisms SHOULD NOT require large
resource consumption on NSIS Entities (for example main memory or
other additional message exchanges) before a successful
authentication is done.
5.7.8 Confidentiality of signaling messages
Based on the signaling information exchanged between nodes
participating in the signaling protocol an adversary may learn both
the identities and the content of the signaling messages. To prevent
this from happening, confidentiality of the signaling message in a
hop-by-hop manner MAY be provided. Note that the protection can be
provided on a hop-by-hop basis for most message payloads since it is
required that entities which actively participating in the signaling
protocol must be able to read and eventually modify the content of
the signaling messages.
5.7.9 Ownership of state
Brunner (Editor) Informational [Page 17]
Requirements for Signaling Protocols March 2003
When existing states have to be modified then there is a need to use
a session identifier to uniquely identify the established state. A
signaling protocol MUST provide means of security protection to
prevent adversaries from modifying state.
5.8 Mobility
5.8.1 Allow efficient service re-establishment after handover
Handover is an essential function in wireless networks. After
handover, the states may need to be completely or partially re-
established due to route changes. The re-establishment may be
requested by the mobile node itself or triggered by the access point
that the mobile node is attached to. In the first case, the
signaling MUST allow efficient re-establishment after handover. Re-
establishment after handover MUST be as quick as possible so that
the mobile node does not experience service interruption or service
degradation. The re-establishment SHOULD be localized, and not
require end-to-end signaling.
5.9 Interworking with other protocols and techniques
Hooks SHOULD be provided to enable efficient interworking between
various protocols and techniques including the following listed.
5.9.1 MUST interwork with IP tunneling
IP tunneling for various applications MUST be supported. More
specifically IPSec tunnels are of importance. This mainly impacts
the identification of flows. When using IPSec, parts of information
commonly used for flow identification (e.g. transport protocol
information and ports) may not be accessible due to encryption.
5.9.2 MUST NOT constrain either to IPv4 or IPv6
5.9.3 MUST be independent from charging model
Signaling MUST NOT be constrained by charging models or the charging
infrastructure used.
5.9.4 SHOULD provide hooks for AAA protocols
The NSIS SHOULD be developed with respect to be able to collect
usage records from one or more network elements.
5.9.5 SHOULD interwork with seamless handoff protocols
An NSIS protocol SHOULD interwork with seamless handoff protocols
such as context transfer and candidate access router (CAR)
discovery.
5.9.6 MAY interwork with non-traditional routing
Brunner (Editor) Informational [Page 18]
Requirements for Signaling Protocols March 2003
NSIS assumes L3 routing, but networks, which do non-traditional
routing, should not break it.
5.10 Operational
5.10.1 Ability to assign transport quality to signaling messages.
The NSIS architecture SHOULD allow the network operator to assign
the NSIS protocol messages a certain transport quality. As signaling
opens up for possible denial-of-service attacks, this requirement
gives the network operator a means, but also the obligation, to
trade-off between signaling latency and the impact (from the
signaling messages) on devices within the network. From protocol
design this requirement states that the protocol messages SHOULD be
detectable, at least where the control and assignment of the
messages priority is done.
Furthermore, the protocol design must take into account reliability
concerns. Communication reliability is seen as part of the quality
assigned to signaling messages. So procedures MUST be defined how an
NSIS signaling system behaves if some kind of request it sent stays
unanswered. The basic transport protocol to be used between adjacent
NSIS Entities MAY ensure message integrity and reliable transport.
5.10.2 Graceful fail over
Any unit participating in NSIS signaling MUST NOT cause further
damage to other systems involved in NSIS signaling when it has to go
out of service.
5.10.3 Graceful handling of NSIS entity problems
NSIS entities SHOULD be able to detect a malfunctioning peer. It may
notify the NSIS Initiator or another NSIS entity involved in the
signaling process. The NSIS peer may handle the problem itself e.g.
switching to a backup NSIS entity. In the latter case note that
synchronization of state between the primary and the backup entity
is needed.
6 Security Considerations
Section 5.7 of this document provides security related requirements
of a signaling protocol.
7 References
7.1 Normative References
[KEYWORDS] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
Brunner (Editor) Informational [Page 19]
Requirements for Signaling Protocols March 2003
7.2 Non-Normative References
[RSVP] Braden, R., Zhang, L., Berson, S., Herzog, A., Jamin, S.,
"Resource Protocol (RSVP) -- Version 1 Functional Specification",
RFC 2205, September 1997.
[RSVP-TE] D. Awduche, L. Berger, D. Gan, T. Li, V. Srinivasan, G.
Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
[RFC3234] B. Carpenter, S. Brim, "Middleboxes: Taxonomy and Issues",
RFC 3234, February 2002.
8 Acknowledgments
Quite a number of people have been involved in the discussion of the
document, adding some ideas, requirements, etc. We list them without
a guarantee on completeness: Changpeng Fan (Siemens), Krishna Paul
(NEC), Maurizio Molina (NEC), Mirko Schramm (Siemens), Andreas
Schrader (NEC), Hannes Hartenstein (NEC), Ralf Schmitz (NEC),
Juergen Quittek (NEC), Morihisa Momona (NEC), Holger Karl (Technical
University Berlin), Xiaoming Fu (Technical University Berlin), Hans-
Peter Schwefel (Siemens), Mathias Rautenberg (Siemens), Christoph
Niedermeier (Siemens), Andreas Kassler (University of Ulm), Ilya
Freytsis.
Some text and/or ideas for text, requirements, scenarios have been
taken from an Internet Draft written by the following authors: David
Partain (Ericsson), Anders Bergsten (Telia Research), Marc Greis
(Nokia), Georgios Karagiannis (Ericsson), Jukka Manner (University
of Helsinki), Ping Pan (Juniper), Vlora Rexhepi (Ericsson), Lars
Westberg (Ericsson), Haihong Zheng (Nokia). Some of those have
actively contributed new text to this document as well.
Another Internet Draft impacting this document has been written by
Sven Van den Bosch, Maarten Buchli, and Danny Goderis (all Alcatel).
These people contributed also new text.
Thanks also to Kwok Ho Chan (Nortel) for text changes.
9 Author's Addresses
Marcus Brunner (Editor)
NEC Europe Ltd.
Network Laboratories
Kurfuersten-Anlage 36
D-69115 Heidelberg
Germany
E-Mail: brunner@ccrle.nec.de
Robert Hancock
Roke Manor Research Ltd
Romsey, Hants, SO51 0ZN
United Kingdom
Brunner (Editor) Informational [Page 20]
Requirements for Signaling Protocols March 2003
E-Mail: robert.hancock@roke.co.uk
Eleanor Hepworth
Roke Manor Research Ltd
Romsey, Hants, SO51 0ZN
United Kingdom
E-Mail: eleanor.hepworth@roke.co.uk
Cornelia Kappler
Siemens AG
Berlin 13623
Germany
E-Mail: cornelia.kappler@icn.siemens.de
Hannes Tschofenig
Siemens AG
Otto-Hahn-Ring 6
81739 Munchen
Germany
Email: Hannes.Tschofenig@mchp.siemens.de
10 Appendix: Scenarios/Use cases
In the following we describe scenarios, which are important to
cover, and which allow us to discuss various requirements. Some
regard this as use cases to be covered defining the use of a
signaling protocol. In general, these scenarios consider the
specific case of signaling for QoS (resource reservation), although
many of the issues carry over directly to other signaling types.
10.1 Terminal Mobility
The scenario we are looking at is the case where a mobile terminal
(MT) changes from one access point to another access point. The
access points are located in separate QoS domains. We assume Mobile
IP to handle mobility on the network layer in this scenario and
consider the various extensions (i.e., IETF proposals) to Mobile IP,
in order to provide 'fast handover' for roaming Mobile Terminals.
The goal to be achieved lies in providing, keeping, and adapting the
requested QoS for the ongoing IP sessions in case of handover.
Furthermore, the negotiation of QoS parameters with the new domain
via the old connection might be needed, in order to support the
different 'fast handover' proposals within the IETF.
The entities involved in this scenario include a mobile terminal,
access points, an access network manager, and communication partners
of the MT (the other end(s) of the communication association).
From a technical point of view, terminal mobility means changing the
access point of a mobile terminal (MT). However, technologies might
change in various directions (access technology, QoS technology,
administrative domain). If the access points are within one specific
QoS technology (independent of access technology) we call this
intra-QoS technology handoff. In the case of an inter-QoS technology
handoff, one change from e.g. a DiffServ to an IntServ domain,
Brunner (Editor) Informational [Page 21]
Requirements for Signaling Protocols March 2003
however still using the same access technology. Finally, if the
access points are using different access technologies we call it
inter-technology hand-off.
The following issues are of special importance in this scenario:
1) Handoff decision
- The QoS management requests handoff. The QoS management can decide
to change the access point, since the traffic conditions of the new
access point are better supporting the QoS requirements. The metric
may be different (optimized towards a single or a group/class of
users). Note that the MT or the network (see below) might trigger
the handoff.
- The mobility management forces handoff. This can have several
reasons. The operator optimizes his network, admission is no longer
granted (e.g. emptied prepaid condition). Or another example is when
the MT is reaching the focus of another base station. However, this
might be detected via measurements of QoS on the physical layer and
is therefore out of scope of QoS signaling in IP. Note again that
the MT or the network (see below) might trigger the handoff.
- This scenario shows that local decisions might not be enough. The
rest of the path to the other end of the communication needs to be
considered as well. Hand-off decisions in a QoS domain do not only
depend on the local resource availability, e.g., the wireless part,
but involve the rest of the path as well. Additionally,
decomposition of an end-to-end signaling might be needed, in order
to change only parts of it.
2) Trigger sources
- Mobile terminal: If the end-system QoS management identifies
another (better-suited) access point, it will request the handoff
from the terminal itself. This will be especially likely in the case
that two different provider networks are involved. Another important
example is when the current access point bearer disappears (e.g.
removing the Ethernet cable). In this case, the NSIS Initiator is
basically located on the mobile terminal.
- Network (access network manager): Sometimes, the handoff trigger
will be issued from the network management to optimize the overall
load situation. Most likely this will result in changing the base-
station of a single providers network. Most likely the NSIS
Initiator is located on a system within the network.
3) Integration with other protocols
- Interworking with other protocol must be considered in one or the
other form. E.g., it might be worth combining QoS signaling between
different QoS domains with mobility signaling at hand-over.
4) Handover rates
Brunner (Editor) Informational [Page 22]
Requirements for Signaling Protocols March 2003
In mobile networks, the admission control process has to cope with
far more admission requests than call setups alone would generate.
For example, in the GSM (Global System for Mobile communications)
case, mobility usually generates an average of one to two handovers
per call. For third generation networks (such as UMTS), where it is
necessary to keep radio links to several cells simultaneously
(macro-diversity), the handover rate is significantly higher.
5) Fast s
Handover can also cause packet losses. This happens when the
processing of an admission request causes a delayed handover to the
new base station. In this situation, some packets might be
discarded, and the overall speech quality might be degraded
significantly. Moreover, a delay in handover may cause degradation
for other users. In the worst-case scenario, a delay in handover may
cause the connection to be dropped if the handover occurred due to
bad air link quality. Therefore, it is critical that QoS signaling
in connection with handover be carried out very quickly.
6) Call blocking in case of overload
Furthermore, when the network is overloaded, it is preferable to
keep s for previously established flows while blocking new requests.
Therefore, the resource reservation requests in connection with
handover should be given higher priority than new requests for
resource reservation.
10.2 3G Wireless Networks
In this scenario, the user is using the packet services of a 3rd
generation wireless system (e.g. 3GPP/UMTS, 3GPP2/cdma2000). The
region between the End Host and the Edge Node (Edge Router)
connecting the wireless network to another QoS domain is considered
to be a single QoS domain.
The issues in such an environment regarding QoS include:
1) 3G wireless networks provide their own QoS technology with
specialized parameters to co-ordinate the QoS provided by both the
radio access and wired access networks. Provisioning of QoS
technologies within a 3G wireless network can be described mainly in
terms of calling bearer classes, service options and service
instances. These QoS technologies need to be invoked with suitable
parameters when higher layers trigger a request for QoS. Therefore
these involve mapping of the requested higher layer QoS parameters
onto specific bearer classes or service instances. The request for
allocation of resources might be triggered by signaling at the IP
level that passes across the wireless system, and possibly other QoS
domains. Typically, wireless network specific messages are invoked
to setup the underlying bearer classes or service instances in
parallel with the IP layer QoS negotiation, to allocate resources
within the radio access network.
Brunner (Editor) Informational [Page 23]
Requirements for Signaling Protocols March 2003
2) The IP signaling messages are initiated by the NSIS initiator and
interpreted by the NSIS Forwarder. The most efficient placement of
the NSIS Initiator and NSIS Forwarder has not been determined in 3G
wireless networks, but a few potential scenarios can be envisioned.
The NSIS Initiator could be located at the End Host e.g. UE or MS
(triggered by applications), the Access Gateway or at a node that is
not directly on the data path, such as a Policy Decision Function.
The Access Gateway could act as a proxy NSIS Initiator on behalf of
the UE/MS or an End Host. The Policy Decision Function that controls
per-flow/aggregate resources with respect to the session within its
QoS domain (e.g. the 3G wireless network) may act as a proxy NSIS
Initiator for the UE/MS or the Access Gateway. Depending on the
placement of the NSIS Initiator, the NSIS Forwarder may be located
at an appropriate point in the 3G wireless network.
3) The need for re-negotiation of resources in a new 3G wireless
domain due to UE/MS mobility. In this case the NSIS Initiator and
the NSIS Forwarder should detect mobility events and autonomously
trigger re-negotiation of resources.
10.3 An example scenario for 3G wireless networks
The 3G wireless access scenario is shown in Figure 1. The Proxy-Call
State Control Function (P-CSCF) is the outbound SIP proxy (only used
in IMS). The Access Gateway is the egress router of the 3G wireless
domain and it connects the radio access network to the Edge Router
(ER) of the backbone IP network. The Policy Decision Function (PDF)
is an entity responsible for controlling bearer level resource
allocations/de-allocations in relation to session level services
e.g. SIP. The Policy Decision Function may also control the Access
Gateway to open and close the gates and to configure per-flow
policies, i.e. to authorize or forbid user traffic. The P-CSCF (only
used in IMS) and the Access Gateway communicate with the Policy
Decision Function, for network resource allocation/de-allocation
decisions. The User Equipment (UE) or the Mobile Station (MS)
consists of a Mobile Terminal (MT) and Terminal Equipment (TE), e.g.
a laptop.
Brunner (Editor) Informational [Page 24]
Requirements for Signaling Protocols March 2003
+--------+
+--------->| P-CSCF |---------> SIP signaling
/ +--------+
/ SIP |
| |
| +-----+ +----------------+
| | PDF |<---------->| NSIS Forwarder |<--->
| +-----+ +----------------+
| | ^
| | |
| | |
| |COPS |
| | |
+------+ +---------+ |
| UE/MS|----------| Access |<-----------+ +----+
+------+ | Gateway |------------------| ER |
+---------+ +----+
Figure 1: 3G wireless access scenario
The PDF has all the required QoS information for per-flow or
aggregate admission control in 3G wireless networks. It receives
resource allocation/de-allocation requests from the P-CSCF and/or
Access Gateway etc. and responds with policy decisions. Hence the
PDF may be a candidate entity to host the functionality of the NSIS
Initiator, initiating the "NSIS" QoS signaling towards the backbone
IP network. On the other hand, the UE/MS may act as the NSIS
Initiator or the Access Gateway may act as a Proxy NSIS Initiator on
behalf of the UE/MS. In the former case, the P-CSCF/PDF has to do
the mapping from codec types and media descriptors (derived from
SIP/SDP signaling) to IP traffic descriptor. In the latter case, the
UE/MS may use any appropriate QoS signaling mechanism as the NSIS
Initiator. If the Access Gateway is acting as the Proxy NSIS
initiator on behalf of the UE/MS, then it may have to do the mapping
of parameters from radio access specific QoS to IP QoS traffic
parameters before forwarding the request to the NSIS Forwarder.
The NSIS Forwarder is currently not part of the standard 3G wireless
architecture. However, to achieve end-to-end QoS a NSIS Forwarder is
needed such that the NSIS Initiators can request a QoS connection to
the IP network. As in the previous example, the NSIS Forwarder could
manage a set of pre-provisioned resources in the IP network, i.e.
bandwidth pipes, and the NSIS Forwarder performs per-flow admission
control into these pipes. In this way, a connection can be made
between two 3G wireless access networks, and hence, end-to-end QoS
can be achieved. In this case the NSIS Initiator and NSIS Forwarder
are clearly two separate logical entities. The Access Gateway or/and
the Edge Router in Fig.1 may contain the NSIS Forwarder
functionality, depending upon the placement of the NSIS Initiator as
discussed in scenario 2 in section 10.2. This use case clearly
illustrates the need for an "NSIS" QoS signaling protocol between
NSIS Initiator and NSIS Forwarder. An important application of such
a protocol may be its use in the end-to-end establishment of a
Brunner (Editor) Informational [Page 25]
Requirements for Signaling Protocols March 2003
connection with specific QoS characteristics between a mobile host
and another party (e.g. end host or content server).
10.4 Wired part of wireless network
A wireless network, seen from a QoS domain perspective, usually
consists of three parts: a wireless interface part (the "radio
interface"), a wired part of the wireless network (i.e., Radio
Access Network) and the backbone of the wireless network, as shown
in Figure 2. Note that this figure should not be seen as an
architectural overview of wireless networks but rather as showing
the conceptual QoS domains in a wireless network.
In this scenario, a mobile host can roam and perform a handover
procedure between base stations/access routers. In this scenario the
NSIS QoS protocol can be applied between a base station and the
gateway (GW). In this case a GW can also be considered as a local
handover anchor point. Furthermore, in this scenario the NSIS QoS
protocol can also be applied either between two GWs, or between two
edge routers (ER).
|--|
|GW|
|--| |--|
|MH|--- .
|--| / |-------| .
/--|base | |--| .
|station|-|ER|...
|-------| |--| . |--| back- |--| |---| |----|
..|ER|.......|ER|..|BGW|.."Internet"..|host|
-- |-------| |--| . |--| bone |--| |---| |----|
|--| \ |base |-|ER|... .
|MH| \ |station| |--| .
|--|--- |-------| . MH = mobile host
|--| ER = edge router
<----> |GW| GW = gateway
Wireless link |--| BGW = border gateway
... = interior nodes
<------------------->
Wired part of wireless network
<---------------------------------------->
Wireless Network
Figure 2. QoS architecture of wired part of wireless network
Each of these parts of the wireless network impose different issues
to be solved on the QoS signaling solution being used:
- Wireless interface: The solution for the air interface link
has to ensure flexibility and spectrum efficient transmission
of IP packets. However, this link layer QoS can be solved in
the same way as any other last hop problem by allowing a
Brunner (Editor) Informational [Page 26]
Requirements for Signaling Protocols March 2003
host to request the proper QoS profile.
- Wired part of the wireless network: This is the part of
the network that is closest to the base stations/access
routers. It is an IP network although some parts logically
perform tunneling of the end user data. In cellular networks,
the wired part of the wireless network is denoted as a
radio access network.
This part of the wireless network has different
characteristics when compared to traditional IP networks:
1. The network supports a high proportion of real-time
traffic. The majority of the traffic transported in the
wired part of the wireless network is speech, which is
very sensitive to delays and delay variation (jitter).
2. The network must support mobility. Many wireless
networks are able to provide a combination of soft
and hard handover procedures. When handover occurs,
reservations need to be established on new paths.
The establishment time has to be as short as possible
since long establishment times for s degrade
the performance of the wireless network. Moreover,
for maximal utilization of the radio spectrum, frequent
handover operations are required.
3. These links are typically rather bandwidth-limited.
4. The wired transmission in such a network contains a
relatively high volume of expensive leased lines.
Overprovisioning might therefore be prohibitively
expensive.
5. The radio base stations are spread over a wide
geographical area and are in general situated a large
distance from the backbone.
- Backbone of the wireless network: the requirements imposed
by this network are similar to the requirements imposed by
other types of backbone networks.
Due to these very different characteristics and requirements, often
contradictory, different QoS signaling solutions might be needed in
each of the three network parts.
10.5 Session Mobility
In this scenario, a session is moved from one end-system to another.
Ongoing sessions are kept and QoS parameters need to be adapted,
since it is very likely that the new device provides different
capabilities. Note that it is open which entity initiates the move,
which implies that the NSIS Initiator might be triggered by
different entities.
Brunner (Editor) Informational [Page 27]
Requirements for Signaling Protocols March 2003
User mobility (i.e., a user changing the device and therefore moving
the sessions to the new device) is considered to be a special case
within the session mobility scenario.
Note that this scenario is different from terminal mobility. Not the
terminal (end-system) has moved to a different access point. Both
terminals are still connected to an IP network at their original
points.
The issues include:
1) Keeping the QoS guarantees negotiated implies that the end-
point(s) of communication are changed without changing the s.
2) The trigger of the session move might be the user or any other
party involved in the session.
10.6 QoS s/negotiation from access to core network
The scenario includes the signaling between access networks and core
networks in order to setup and change s together with potential
negotiation.
The issues to be solved in this scenario are different from previous
ones.
1) The entity of reservation is most likely an aggregate.
2) The time scales of s might be different (long living s of
aggregates, less often re-negotiation).
3) The specification of the traffic (amount of traffic), a
particular QoS is guaranteed for, needs to be changed. E.g., in case
additional flows are added to the aggregate, the traffic
specification of the flow needs to be added if it is not already
included in the aggregates specification.
4) The flow specification is more complex including network
addresses and sets of different address for the source as well as
for the destination of the flow.
10.7 QoS /negotiation over administrative boundaries
Signaling between two or more core networks to provide QoS is
handled in this scenario. This might also include access to core
signaling over administrative boundaries. Compared to the previous
one it adds the case, where the two networks are not in the same
administrative domain. Basically, it is the inter-domain/inter
provider signaling which is handled in here.
The domain boundary is the critical issue to be resolved. Which as
various flavors of issues a QoS signaling protocol has to be
concerned with.
Brunner (Editor) Informational [Page 28]
Requirements for Signaling Protocols March 2003
1) Competing administrations: Normally, only basic information
should be exchanged, if the signaling is between competing
administrations. Specifically information about core network
internals (e.g., topology, technology, etc.) should not be
exchanged. Some information exchange about the "access points" of
the core networks (which is topology information as well) may need
to be exchanged, because it is needed for proper signaling.
2) Additionally, as in scenario 4, signaling most likely is based on
aggregates, with all the issues raise there.
3) Authorization: It is critical that the NSIS Initiator is
authorized to perform a QoS path setup.
4) Accountability: It is important to notice that signaling might be
used as an entity to charge money for, therefore the interoperation
with accounting needs to be available.
10.8 QoS signaling between PSTN gateways and backbone routers
A PSTN gateway (i.e., host) requires information from the network
regarding its ability to transport voice traffic across the network.
The voice quality will suffer due to packet loss, latency and
jitter. Signaling is used to identify and admit a flow for which
these impairments are minimized. In addition, the disposition of
the signaling request is used to allow the PSTN GW to make a call
routing decision before the call is actually accepted and delivered
to the final destination.
PSTN gateways may handle thousands of calls simultaneously and there
may be hundreds of PSTN gateways in a single provider network. These
numbers are likely to increase as the size of the network increases.
The point being that scalability is a major issue.
There are several ways that a PSTN gateway can acquire assurances
that a network can carry its traffic across the network. These
include:
1. Over-provisioning a high availability network.
2. Handling admission control through some policy server
that has a global view of the network and its resources.
3. Per PSTN GW pair admission control.
4. Per call admission control (where a call is defined as
the 5-tuple used to carry a single RTP flow).
Item 1 requires no signaling at all and is therefore outside the
scope of this working group.
Item 2 is really a better informed version of 1, but it is also
outside the scope of this working group as it relies on a particular
telephony signaling protocol rather than a packet admission control
protocol.
Brunner (Editor) Informational [Page 29]
Requirements for Signaling Protocols March 2003
Item 3 is initially attractive, as it appears to have reasonable
scaling properties, however, its scaling properties only are
effective in cases where there are relatively few PSTN GWs. In the
more general case were a PSTN GW reduces to a single IP phone
sitting behind some access network, the opportunities for
aggregation are reduced and the problem reduces to item 4.
Item 4 is the most general case. However, it has the most difficult
scaling problems. The objective here is to place the requirements on
Item 4 such that a scalable per-flow admission control protocol or
protocol suite may be developed.
The case where per-flow signaling extends to individual IP end-
points allows the inclusion of IP phones on cable, DSL, wireless or
other access networks in this scenario.
Call Scenario
A PSTN GW signals end-to-end for some 5-tuple defined flow a
bandwidth and QoS requirement. Note that the 5-tuple might include
masking/wildcarding. The access network admits this flow according
to its local policy and the specific details of the access
technology.
At the edge router (i.e., border node), the flow is admitted, again
with an optional authentication process, possibly involving an
external policy server. Note that the relationship between the PSTN
GW and the policy server and the routers and the policy server is
outside the scope of NSIS. The edge router then admits the flow into
the core of the network, possibly using some aggregation technique.
At the interior nodes, the NSIS host-to-host signaling should either
be ignored or invisible as the Edge router performed the admission
control decision to some aggregate.
At the inter-provider router (i.e., border node), again the NSIS
host-to-host signaling should either be ignored or invisible, as the
Edge router has performed an admission control decision about an
aggregate across a carrier network.
10.9 PSTN trunking gateway
One of the use cases for the NSIS signaling protocol is the scenario
of interconnecting PSTN gateways with an IP network that supports
QoS.
Four different scenarios are considered here.
1. In-band QoS signaling is used. In this case the Media Gateway
(MG) will be acting as the NSIS Initiator and the Edge Router
(ER) will be the NSIS Forwarder. Hence, the ER should do
admission control (into pre-provisioned traffic trunks) for the
individual traffic flows. This scenario is not further
considered here.
Brunner (Editor) Informational [Page 30]
Requirements for Signaling Protocols March 2003
2. Out-of-band signaling in a single domain, the NSIS forwarder is
integrated in the MGC. In this case no NSIS protocol is
required.
3. Out-of-band signaling in a single domain, the NSIS forwarder is
a separate box. In this case NSIS signaling is used between the
MGC and the NSIS Forwarder.
4. Out-of-band signaling between multiple domains, the NSIS
Forwarder (which may be integrated in the MGC) triggers the
NSIS Forwarder of the next domain.
When the out-of-band QoS signaling is used the Media Gateway
Controller (MGC) will be acting as the NSIS Initiator.
In the second scenario the voice provider manages a set of traffic
trunks that are leased from a network provider. The MGC does the
admission control in this case. Since the NSIS Forwarder acts both
as a NSIS Initiator and a NSIS Forwarder, no NSIS signaling is
required. This scenario is shown in Figure 3.
+-------------+ ISUP/SIGTRAN +-----+ +-----+
| SS7 network |---------------------| MGC |--------------| SS7 |
+-------------+ +-------+-----+---------+ +-----+
: / : \
: / : \
: / +--------:----------+ \
: MEGACO / / : \ \
: / / +-----+ \ \
: / / | NMS | \ \
: / | +-----+ | \
: : | | :
+--------------+ +----+ | bandwidth pipe (SLS) | +----+
| PSTN network |--| MG |--|ER|======================|ER|-| MG |--
+--------------+ +----+ \ / +----+
\ QoS network /
+-------------------+
Figure 3: PSTN trunking gateway scenario
In the third scenario, the voice provider does not lease traffic
trunks in the network. Another entity may lease traffic trunks and
may use a NSIS Forwarder to do per-flow admission control. In this
case the NSIS signaling is used between the MGC and the NSIS
Forwarder, which is a separate box here. Hence, the MGC acts only as
a NSIS Initiator. This scenario is depicted in Figure 4.
Brunner (Editor) Informational [Page 31]
Requirements for Signaling Protocols March 2003
+-------------+ ISUP/SIGTRAN +-----+ +-----+
| SS7 network |---------------------| MGC |--------------| SS7 |
+-------------+ +-------+-----+---------+ +-----+
: / : \
: / +-----+ \
: / | NF | \
: / +-----+ \
: / : \
: / +--------:----------+ \
: MEGACO : / : \ :
: : / +-----+ \ :
: : / | NMS | \ :
: : | +-----+ | :
: : | | :
+--------------+ +----+ | bandwidth pipe (SLS) | +----+
| PSTN network |--| MG |--|ER|======================|ER|-| MG |--
+--------------+ +----+ \ / +----+
\ QoS network /
+-------------------+
Figure 4: PSTN trunking gateway scenario
In the fourth scenario multiple transport domains are involved. In
the originating network either the MGC may have an overview on the
resources of the overlay network or a separate NSIS Forwarder will
have the overview. Hence, depending on this either the MGC or the
NSIS Forwarder of the originating domain will contact the NSIS
Forwarder of the next domain. The MGC always acts as a NSIS
Initiator and may also be acting as a NSIS Forwarder in the first
domain.
10.10 Application request end-to-end QoS path from the network
This is actually the easiest case, nevertheless might be most often
used in terms of number of users. So multimedia application requests
a guaranteed service from an IP network. We assume here that the
application is somehow able to specify the network service. The
characteristics here are that many hosts might do it, but that the
requested service is low capacity (bounded by the access line).
Additionally, we assume no mobility and standard devices.
QOS for Virtual Private Networks
In a Virtual Private Network (VPN) a variety of tunnels might be
used between its edges. These tunnels could be for example, IP-Sec,
GRE, and IP-IP. One of the most significant issues in VPNs is
related to how a flow is identified and what quality a flow gets. A
flow identification might consist among others of the transport
protocol port numbers. In an IP-Sec tunnel this will be problematic
since the transport protocol information is encrypted.
There are two types of L3 VPNs, distinguished by where the endpoints
of the tunnels exist. The endpoints of the tunnels may either be on
the customer (CPE) or the provider equipment or provider edge (PE).
Brunner (Editor) Informational [Page 32]
Requirements for Signaling Protocols March 2003
Virtual Private networks are also likely to request bandwidth or
other type of service in addition to the premium services the PSTN
GW are likely to use.
Tunnel end points at the Customer premises
When the endpoints are the CPE, the CPE may want to signal across
the public IP network for a particular amount of bandwidth and QoS
for the tunnel aggregate. Such signaling may be useful when a
customer wants to vary their network cost with demand, rather than
paying a flat rate. Such signaling exists between the two CPE
routers. Intermediate access and edge routers perform the same exact
call admission control, authentication and aggregation functions
performed by the corresponding routers in the PSTN GW scenario with
the exception that the endpoints are the CPE tunnel endpoints rather
than PSTN GWs and the 5-tuple used to describe the RTP flow is
replaced with the corresponding flow spec to uniquely identify the
tunnels. Tunnels may be of any variety (e.g. IP-Sec, GRE, IP-IP).
In such a scenario, NSIS would actually allow partly for customer
managed VPNs, which means a customer can setup VPNs by subsequent
NSIS signaling to various end-point. Plus the tunnel end-points are
not necessarily bound to an application. The customer administrator
might be the one triggering NSIS signaling.
Tunnel end points at the provider premises
In the case were the tunnel end-points exist on the provider edge,
requests for bandwidth may be signaled either per flow, where a flow
is defined from a customers address space, or between customer
sites.
In the case of per flow signaling, the PE router must map the
bandwidth request to the tunnel carrying traffic to the destination
specified in the flow spec. Such a tunnel is a member of an
aggregate to which the flow must be admitted. In this case, the
operation of admission control is very similar to the case of the
PSTN GW with the additional level of indirection imposed by the VPN
tunnel. Therefore, authentication, accounting and policing may be
required on the PE router.
In the case of per site signaling, a site would need to be
identified. This may be accomplished by specifying the network
serviced at that site through an IP prefix. In this case, the
admission control function is performed on the aggregate to the PE
router connected to the site in question.
Full Copyright Statement
Copyright (C) The Internet Society (2002). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
Brunner (Editor) Informational [Page 33]
Requirements for Signaling Protocols March 2003
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDIN
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Notices
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances
of licenses to be made available, or the result of an attempt made
to obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification
can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights, which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Brunner (Editor) Informational [Page 34]