Internet-Draft | MUD (D)TLS Profile for IoT devices | January 2024 |
Reddy, et al. | Expires 26 July 2024 | [Page] |
- Workgroup:
- OPSAWG WG
- Internet-Draft:
- draft-ietf-opsawg-mud-tls-13
- Published:
- Intended Status:
- Standards Track
- Expires:
Manufacturer Usage Description (MUD) (D)TLS Profiles for IoT Devices
Abstract
This memo extends the Manufacturer Usage Description (MUD) specification to incorporate (D)TLS profile parameters. This allows a network security service to identify unexpected (D)TLS usage, which can indicate the presence of unauthorized software or malware on an endpoint.¶
Status of This Memo
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 26 July 2024.¶
Copyright Notice
Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
1. Introduction
Encryption is necessary to enhance the privacy of end users using IoT devices. TLS [RFC8446] and DTLS [RFC9147] are the dominant protocols (counting all (D)TLS versions) providing encryption for IoT device traffic. Unfortunately, in conjunction with IoT applications' rise of encryption, malware authors are also using encryption which thwarts network-based analysis such as deep packet inspection (DPI). Other mechanisms are thus needed to help detecting malware running on an IoT device.¶
Malware frequently uses proprietary libraries for its activities, and those libraries are reused much like any other software engineering project. [malware] indicates that there are observable differences in how malware uses encryption compared with how non-malware uses encryption. There are several interesting findings specific to (D)TLS which were found common to malware:¶
-
Older and weaker cryptographic parameters (e.g., TLS_RSA_WITH_RC4_128_SHA).¶
-
TLS server name indication (SNI) extension [RFC6066] and server certificates are composed of subjects with characteristics of a domain generation algorithm (DGA) (e.g., 'www.33mhwt2j.net').¶
-
Higher use of self-signed certificates compared with typical legitimate software.¶
-
Discrepancies in the SNI TLS extension and the DNS names in the SubjectAltName (SAN) X.509 extension in the server certificate message.¶
-
Discrepancies in the key exchange algorithm and the client public key length in comparison with legitimate flows. As a reminder, the Client Key Exchange message has been removed from TLS 1.3.¶
-
Lower diversity in TLS client advertised extensions compared to legitimate clients.¶
-
Using privacy enhancing technologies like Tor, Psiphon, Ultrasurf (see [malware-tls]), and evasion techniques such as ClientHello randomization.¶
-
Using DNS-over-HTTPS (DoH) [RFC8484] to avoid detection by malware DNS filtering services [malware-doh]. Specifically, malware may not use the DoH server provided by the local network.¶
If observable (D)TLS profile parameters are used, the following functions are possible which have a positive impact on the local network security:¶
-
Permit intended DTLS or TLS use and block malicious DTLS or TLS use. This is superior to the layers 3 and 4 ACLs of Manufacturer Usage Description Specification (MUD) [RFC8520] which are not suitable for broad communication patterns.¶
-
Ensure TLS certificates are valid. Several TLS deployments have been vulnerable to active Man-In-The-Middle (MITM) attacks because of the lack of certificate validation or vulnerability in the certificate validation function (see [cryto-vulnerability]). By observing (D)TLS profile parameters, a network element can detect when the TLS SNI mismatches the SubjectAltName and when the server's certificate is invalid. In (D)TLS 1.2 [RFC5246][RFC6347], the ClientHello, ServerHello and Certificate messages are all sent in clear-text. This check is not possible with (D)TLS 1.3, which encrypts the Certificate message thereby hiding the server identity from any intermediary. In (D)TLS 1.3, the server certificate validation functions should be executed within an on-path (D)TLS proxy, if such a proxy exists.¶
-
Support new communication patterns. An IoT device can learn a new capability, and the new capability can change the way the IoT device communicates with other devices located in the local network and Internet. There would be an inaccurate policy if an IoT device rapidly changes the IP addresses and domain names it communicates with while the MUD ACLs were slower to update (see [clear-as-mud]). In such a case, observable (D)TLS profile parameters can be used to permit intended use and to block malicious behavior from the IoT device.¶
The YANG module specified in Section 5.2 of this document is an extension of YANG Data Model for Network Access Control Lists (ACLs) [RFC8519] to enhance MUD [RFC8520] to model observable (D)TLS profile parameters. Using these (D)TLS profile parameters, an active MUD-enforcing network security service (e.g., firewall) can identify MUD non-compliant (D)TLS behavior indicating outdated cryptography or malware. This detection can prevent malware downloads, block access to malicious domains, enforce use of strong ciphers, stop data exfiltration, etc. In addition, organizations may have policies around acceptable ciphers and certificates for the websites the IoT devices connect to. Examples include no use of old and less secure versions of TLS, no use of self-signed certificates, deny-list or accept-list of Certificate Authorities, valid certificate expiration time, etc. These policies can be enforced by observing the (D)TLS profile parameters. Network security services can use the IoT device's (D)TLS profile parameters to identify legitimate flows by observing (D)TLS sessions, and can make inferences to permit legitimate flows and to block malicious or insecure flows. The proposed technique is also suitable in deployments where decryption techniques are not ideal due to privacy concerns, non-cooperating end-points, and expense.¶
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119][RFC8174] when, and only when, they appear in all capitals, as shown here.¶
"(D)TLS" is used for statements that apply to both Transport Layer Security [RFC8446] and Datagram Transport Layer Security [RFC6347]. Specific terms "TLS" and "DTLS" are used for any statement that applies to either protocol alone.¶
'DoH/DoT' refers to DNS-over-HTTPS and/or DNS-over-TLS.¶
3. Overview of MUD (D)TLS profiles for IoT devices
In Enterprise networks, protection and detection are typically done both on end hosts and in the network. Host security agents have deep visibility on the devices where they are installed, whereas the network has broader visibility. Installing host security agents may not be a viable option on IoT devices, and network-based security is an efficient means to protect such IoT devices. If the IoT device supports a MUD (D)TLS profile, the (D)TLS profile parameters of the IoT device can be used by a middlebox to detect and block malware communication, while at the same time preserving the privacy of legitimate uses of encryption. The middlebox need not proxy (D)TLS but can passively observe the parameters of (D)TLS handshakes from IoT devices and gain visibility into TLS 1.2 parameters and partial visibility into TLS 1.3 parameters.¶
Malicious agents can try to use the (D)TLS profile parameters of legitimate agents to evade detection, but it becomes a challenge to mimic the behavior of various IoT device types and IoT device models from several manufacturers. In other words, malware developers will have to develop malicious agents per IoT device type, manufacturer and model, infect the device with the tailored malware agent and will have keep up with updates to the device's (D)TLS profile parameters over time. Furthermore, the malware's command and control server certificates need to be signed by the same certifying authorities trusted by the IoT devices. Typically, IoT devices have an infrastructure that supports a rapid deployment of updates, and malware agents will have a near-impossible task of similarly deploying updates and continuing to mimic the TLS behavior of the IoT device it has infected. However, if the IoT device has reached end-of-life and the IoT manufacturer will not issue a firmware or software update to the Thing or will not update the MUD file, the "is-supported" attribute defined in Section 3.6 of [RFC8520] can be used by the MUD manager to identify the IoT manufacturer no longer supports the device.¶
The end-of-life of a device does not necessarily mean that it is defective; rather, it denotes a need to replace and upgrade the network to next-generation devices for additional functionality. The network security service will have to rely on other techniques discussed in Section 8 to identify malicious connections until the device is replaced.¶
Compromised IoT devices are typically used for launching DDoS attacks (Section 3 of [RFC8576]). For example, DDoS attacks like Slowloris and Transport Layer Security (TLS) re-negotiation can be blocked if the victim's server certificate is not be signed by the same certifying authorities trusted by the IoT device.¶
4. (D)TLS 1.3 Handshake
In (D)TLS 1.3, full (D)TLS handshake inspection is not possible since all (D)TLS handshake messages excluding the ClientHello message are encrypted. (D)TLS 1.3 has introduced new extensions in the handshake record layers called Encrypted Extensions. Using these extensions handshake messages will be encrypted and network security services (such as a firewall) are incapable of deciphering the handshake, and thus cannot view the server certificate. However, the ClientHello and ServerHello still have some fields visible, such as the list of supported versions, named groups, cipher suites, signature algorithms and extensions in ClientHello, and chosen cipher in the ServerHello. For instance, if the malware uses evasion techniques like ClientHello randomization, the observable list of cipher suites and extensions offered by the malware agent in the ClientHello message will not match the list of cipher suites and extensions offered by the legitimate client in the ClientHello message, and the middlebox can block malicious flows without acting as a (D)TLS 1.3 proxy.¶
4.1. Full (D)TLS 1.3 Handshake Inspection
To obtain more visibility into negotiated TLS 1.3 parameters, a middlebox can act as a (D)TLS 1.3 proxy. A middlebox can act as a (D)TLS proxy for the IoT devices owned and managed by the IT team in the Enterprise network and the (D)TLS proxy must meet the security and privacy requirements of the organization. In other words, the scope of middlebox acting as a (D)TLS proxy is restricted to Enterprise network owning and managing the IoT devices. The middlebox would have to follow the behaviour detailed in Section 9.3 of [RFC8446] to act as a compliant (D)TLS 1.3 proxy.¶
To further increase privacy, Encrypted Client Hello (ECH) extension [I-D.ietf-tls-esni] prevents passive observation of the TLS Server Name Indication extension and other potentially sensitive fields, such as the ALPN [RFC7301]. To effectively provide that privacy protection, ECH extension needs to be used in conjunction with DNS encryption (e.g., DoH). A middlebox (e.g., firewall) passively inspecting ECH extension cannot observe the encrypted SNI nor observe the encrypted DNS traffic. The middlebox acting as a (D)TLS 1.3 proxy that does not support ECH extension will act as if connecting to the public name and it follows the behaviour discussed in Section 6.1.6 of [I-D.ietf-tls-esni] to securely signal the client to disable ECH.¶
4.2. Encrypted DNS
A common usage pattern for certain type of IoT devices (e.g., light bulb) is for it to "call home" to a service that resides on the public Internet, where that service is referenced through a domain name (A or AAAA record). As discussed in Manufacturer Usage Description Specification [RFC8520], because these devices tend to require access to very few sites, all other access should be considered suspect. If an IoT device is pre-configured to use a DNS resolver not signaled by the network, the MUD policy enforcement point is moved to that resolver, which cannot enforce the MUD policy based on domain names (Section 8 of [RFC8520]). If the DNS query is not accessible for inspection, it becomes quite difficult for the infrastructure to suspect anything. Thus the use of a DNS resolver not signaled by the network is incompatible with MUD in general. A network-designated DoH/DoT server is necessary to allow MUD policy enforcement on the local network, for example, using the techniques specified in DNR[RFC9463] and DDR [RFC9462].¶
5. (D)TLS Profile of a IoT device
This document specifies a YANG module for representing (D)TLS profile. The (D)TLS profile YANG module provides a method for network security services to observe the (D)TLS profile parameters in the (D)TLS handshake to permit intended use and to block malicious behavior. This module uses the cryptographic types defined in [I-D.ietf-netconf-crypto-types]. See [RFC7925] for (D)TLS 1.2 and [I-D.ietf-uta-tls13-iot-profile] for DTLS 1.3 recommendations related to IoT devices, and [RFC7525] for additional (D)TLS 1.2 recommendations.¶
A companion YANG module is defined to include a collection of (D)TLS parameters and (D)TLS versions maintained by IANA: "iana-tls-profile" (Section 5.3).¶
The (D)TLS parameters in each (D)TLS profile include the following:¶
-
Profile name¶
-
(D)TLS versions supported by the IoT device.¶
-
List of supported cipher suites (Section 11 of [RFC8446]). For (D)TLS1.2, [RFC7925] recommends AEAD ciphers for IoT devices.¶
-
List of supported extension types¶
-
List of trust anchor certificates used by the IoT device. If the server certificate is signed by one of the trust anchors, the middlebox continues with the connection as normal. Otherwise, the middlebox will react as if the server certificate validation has failed and takes appropriate action (e.g, block the (D)TLS session). An IoT device can use a private trust anchor to validate a server's certificate (e.g., the private trust anchor can be preloaded at manufacturing time on the IoT device and the IoT device fetches the firmware image from the Firmware server whose certificate is signed by the private CA). This empowers the middlebox to reject TLS sessions to servers that the IoT device does not trust.¶
-
List of pre-shared key exchange modes¶
-
List of named groups (DHE or ECDHE) supported by the client¶
-
List of signature algorithms the client can validate in X.509 server certificates¶
-
List of signature algorithms the client is willing to accept for CertificateVerify message (Section 4.2.3 of [RFC8446]). For example, a TLS client implementation can support different sets of algorithms for certificates and in TLS to signal the capabilities in "signature_algorithms_cert" and "signature_algorithms" extensions.¶
-
List of supported application protocols (e.g., h3, h2, http/1.1 etc.)¶
-
List of certificate compression algorithms (defined in [RFC8879])¶
-
List of the distinguished names [X501] of acceptable certificate authorities, represented in DER-encoded format [X690] (defined in Section 4.2.4 of [RFC8446])¶
GREASE [RFC8701] defines a mechanism for TLS peers to send random values on TLS parameters to ensure future extensibility of TLS extensions. Similar random values might be extended to other TLS parameters. Thus, the (D)TLS profile parameters defined in the YANG module by this document MUST NOT include the GREASE values for extension types, named groups, signature algorithms, (D)TLS versions, pre-shared key exchange modes, cipher suites and for any other TLS parameters defined in future RFCs.¶
The (D)TLS profile does not include parameters like compression methods for data compression, [RFC7525] recommends disabling TLS-level compression to prevent compression-related attacks. In TLS 1.3, only the "null" compression method is allowed (Section 4.1.2 of [RFC8446]).¶
5.1. Tree Structure of the (D)TLS profile Extension to the ACL YANG Model
This document augments the "ietf-acl" ACL YANG module defined in [RFC8519] for signaling the IoT device (D)TLS profile. This document defines the YANG module "ietf-acl-tls". The meaning of the symbols in the YANG tree diagram are defined in [RFC8340] and it has the following tree structure:¶
module: ietf-acl-tls augment /acl:acls/acl:acl/acl:aces/acl:ace/acl:matches: +--rw client-profiles {match-on-tls-dtls}? +--rw tls-dtls-profile* [name] +--rw name string +--rw supported-tls-version* ianatp:tls-version +--rw supported-dtls-version* ianatp:dtls-version +--rw cipher-suite* ianatp:cipher-algorithm +--rw extension-type* | ianatp:extension-type +--rw accept-list-ta-cert* | ct:trust-anchor-cert-cms +--rw psk-key-exchange-mode* | ianatp:psk-key-exchange-mode | {tls13 or dtls13}? +--rw supported-groups* | ianatp:supported-group +--rw signature-algorithm-cert* | ianatp:signature-algorithm | {tls13 or dtls13}? +--rw signature-algorithm* | ianatp:signature-algorithm +--rw application-protocol* | ianatp:application-protocol +--rw cert-compression-algorithm* | ianatp:cert-compression-algorithm | {tls13 or dtls13}? +--rw certificate-authorities* certificate-authority {tls13 or dtls13}?¶
5.2. The (D)TLS profile Extension to the ACL YANG Model
<CODE BEGINS> file "ietf-acl-tls@2024-23-01.yang" module ietf-acl-tls { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-acl-tls"; prefix acl-tls; import iana-tls-profile { prefix ianatp; reference "RFC XXXX: Manufacturer Usage Description (MUD) (D)TLS Profiles for IoT Devices"; } import ietf-crypto-types { prefix ct; reference "draft-ietf-netconf-crypto-types: YANG Data Types and Groupings for Cryptography"; } import ietf-access-control-list { prefix acl; reference "RFC 8519: YANG Data Model for Network Access Control Lists (ACLs)"; } organization "IETF OPSAWG (Operations and Management Area Working Group)"; contact "WG Web: <https://datatracker.ietf.org/wg/opsawg/> WG List: opsawg@ietf.org Author: Konda, Tirumaleswar Reddy kondtir@gmail.com "; description "This YANG module defines a component that augments the IETF description of an access list to allow (D)TLS profile as matching criteria. Copyright (c) 2020 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices."; revision 2022-10-10 { description "Initial revision"; reference "RFC XXXX: Manufacturer Usage Description (MUD) (D)TLS Profiles for IoT Devices"; } feature tls12 { description "TLS Protocol Version 1.2 is supported."; reference "RFC 5246: The Transport Layer Security (TLS) Protocol Version 1.2"; } feature tls13 { description "TLS Protocol Version 1.3 is supported."; reference "RFC 8446: The Transport Layer Security (TLS) Protocol Version 1.3"; } feature dtls12 { description "DTLS Protocol Version 1.2 is supported."; reference "RFC 6347: Datagram Transport Layer Security Version 1.2"; } feature dtls13 { description "DTLS Protocol Version 1.3 is supported."; reference "RFC 9147: Datagram Transport Layer Security 1.3"; } feature match-on-tls-dtls { description "The networking device can support matching on (D)TLS parameters."; } typedef spki-pin-set { type binary; description "Subject Public Key Info pin set as discussed in Section 2.4 of RFC7469."; } typedef certificate-authority { type string; description "Distinguished Name of Certificate authority as discussed in Section 4.2.4 of RFC8446."; } augment "/acl:acls/acl:acl/acl:aces/acl:ace/acl:matches" { if-feature "match-on-tls-dtls"; description "(D)TLS specific matches."; container client-profiles { description "A grouping for (D)TLS profiles."; list tls-dtls-profile { key "name"; description "A list of (D)TLS version profiles supported by the client."; leaf name { type string { length "1..64"; } description "The name of (D)TLS profile; space and special characters are not allowed."; } leaf-list supported-tls-version { type ianatp:tls-version; description "TLS versions supported by the client."; } leaf-list supported-dtls-version { type ianatp:dtls-version; description "DTLS versions supported by the client."; } leaf-list cipher-suite { type ianatp:cipher-algorithm; description "A list of Cipher Suites supported by the client."; } leaf-list extension-type { type ianatp:extension-type; description "A list of Extension Types supported by the client."; } leaf-list accept-list-ta-cert { type ct:trust-anchor-cert-cms; description "A list of trust anchor certificates used by the client."; } leaf-list psk-key-exchange-mode { if-feature "tls13 or dtls13"; type ianatp:psk-key-exchange-mode; description "pre-shared key exchange modes."; } leaf-list supported-group { type ianatp:supported-group; description "A list of named groups supported by the client."; } leaf-list signature-algorithm-cert { if-feature "tls13 or dtls13"; type ianatp:signature-algorithm; description "A list signature algorithms the client can validate in X.509 certificates."; } leaf-list signature-algorithm { type ianatp:signature-algorithm; description "A list signature algorithms the client can validate in the CertificateVerify message."; } leaf-list application-protocol { type ianatp:application-protocol; description "A list application protocols supported by the client."; } leaf-list cert-compression-algorithm { if-feature "tls13 or dtls13"; type ianatp:cert-compression-algorithm; description "A list certificate compression algorithms supported by the client."; } leaf-list certificate-authorities { if-feature "tls13 or dtls13"; type certificate-authority; description "A list of the distinguished names of certificate authorities acceptable to the client."; } } } } } <CODE ENDS>¶
5.3. IANA (D)TLS profile YANG Module
The TLS and DTLS IANA registries are available from https://www.iana.org/assignments/tls-parameters/tls-parameters.txt and https://www.iana.org/assignments/tls-extensiontype-values/tls-extensiontype-values.txt. Changes to TLS and DTLS related IANA registries are discussed in [RFC8447].¶
The values for all the parameters in the "iana-tls-profile" YANG module are defined in the TLS and DTLS IANA registries excluding the tls-version, dtls-version, spki-pin-set, and certificate-authority parameters. The values of spki-pin-set and certificate-authority parameters will be specific to the IoT device.¶
The TLS and DTLS IANA registries do not maintain (D)TLS version numbers. In (D)TLS 1.2 and below, "legacy_version" field in the ClientHello message is used for version negotiation. However in (D)TLS 1.3, the "supported_versions" extension is used by the client to indicate which versions of (D)TLS it supports. TLS 1.3 ClientHello messages are identified as having a "legacy_version" of 0x0303 and a "supported_versions" extension present with 0x0304 as the highest version. DTLS 1.3 ClientHello messages are identified as having a "legacy_version" of 0xfefd and a "supported_versions" extension present with 0x0304 as the highest version.¶
In order to ease updating the "iana-tls-profile" YANG module with future (D)TLS versions, new (D)TLS version registries are defined in Section 10.2 and Section 10.3. Whenever a new (D)TLS protocol version is defined, the registry will be updated using expert review; the "iana-tls-profile" YANG module will be automatically updated by IANA.¶
Implementers or users of this specification must refer to the IANA-maintained "iana-tls-profile" YANG module available at XXXX [Note to RFC Editor to replace "XXXX" with the URL link of the IANA-maintained "iana-tls-profile" YANG module].¶
The initial version of the "iana-tls-profile" YANG module is defined as follows:¶
<CODE BEGINS> file "iana-tls-profile@2024-23-01.yang" module iana-tls-profile { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:iana-tls-profile"; prefix ianatp; organization "IANA"; contact " Internet Assigned Numbers Authority Postal: ICANN 12025 Waterfront Drive, Suite 300 Los Angeles, CA 90094-2536 United States Tel: +1 310 301 5800 E-Mail: iana@iana.org>"; description "This module contains YANG definition for the (D)TLS profile. Copyright (c) 2020 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices."; revision 2022-10-10 { description "Initial revision"; reference "RFC XXXX: Manufacturer Usage Description (MUD) (D)TLS Profiles for IoT Devices"; } typedef extension-type { type uint16; description "Extension type in the TLS ExtensionType Values registry as defined in Section 7 of RFC8447."; } typedef supported-group { type uint16; description "Supported Group in the TLS Supported Groups registry as defined in Section 9 of RFC8447."; } typedef signature-algorithm { type uint16; description "Signature algorithm in the TLS SignatureScheme registry as defined in Section 11 of RFC8446."; } typedef psk-key-exchange-mode { type uint8; description "Pre-shared key exchange mode in the TLS PskKeyExchangeMode registry as defined in Section 11 of RFC8446."; } typedef application-protocol { type string; description "Application-Layer Protocol Negotiation (ALPN) Protocol ID registry as defined in Section 6 of RFC7301."; } typedef cert-compression-algorithm { type uint16; description "Certificate compression algorithm in TLS Certificate Compression Algorithm IDs registry as defined in Section 7.3 of RFC8879."; } typedef cipher-algorithm { type uint16; description "Cipher suite in TLS Cipher Suites registry as discussed in Section 11 of RFC8446."; } typedef tls-version { type enumeration { enum tls12 { value 1; description "TLS Protocol Version 1.2. TLS 1.2 ClientHello contains 0x0303 in 'legacy_version'."; reference "RFC 5246: The Transport Layer Security (TLS) Protocol Version 1.2"; } enum tls13 { value 2; description "TLS Protocol Version 1.3. TLS 1.3 ClientHello contains a supported_versions extension with 0x0304 contained in its body and the ClientHello contains 0x0303 in 'legacy_version'."; reference "RFC 8446: The Transport Layer Security (TLS) Protocol Version 1.3"; } } description "Indicates the TLS version."; } typedef dtls-version { type enumeration { enum dtls12 { value 1; description "DTLS Protocol Version 1.2. DTLS 1.2 ClientHello contains 0xfefd in 'legacy_version'."; reference "RFC 6347: Datagram Transport Layer Security 1.2"; } enum dtls13 { value 2; description "DTLS Protocol Version 1.3. DTLS 1.3 ClientHello contains a supported_versions extension with 0x0304 contained in its body and the ClientHello contains 0xfefd in 'legacy_version'."; reference "RFC 9147: Datagram Transport Layer Security 1.3"; } } description "Indicates the DTLS version."; } } <CODE ENDS>¶
5.4. MUD (D)TLS Profile Extension
This document augments the "ietf-mud" MUD YANG module to indicate whether the device supports (D)TLS profile. If the "ietf-mud-tls" extension is supported by the device, MUD file is assumed to implement the "match-on-tls-dtls" ACL model feature defined in this specification. Furthermore, only "accept" or "drop" actions SHOULD be included with the (D)TLS profile similar to the actions allowed in Section 2 of [RFC8520].¶
This document defines the YANG module "ietf-mud-tls", which has the following tree structure:¶
module: ietf-mud-tls augment /ietf-mud:mud: +--rw is-tls-dtls-profile-supported? boolean¶
The model is defined as follows:¶
<CODE BEGINS> file "ietf-mud-tls@2020-10-20.yang" module ietf-mud-tls { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-mud-tls"; prefix ietf-mud-tls; import ietf-mud { prefix ietf-mud; reference "RFC 8520: Manufacturer Usage Description Specification"; } organization "IETF OPSAWG (Operations and Management Area Working Group)"; contact "WG Web: <https://datatracker.ietf.org/wg/opsawg/> WG List: opsawg@ietf.org Author: Konda, Tirumaleswar Reddy kondtir@gmail.com "; description "Extension to a MUD module to indicate (D)TLS profile support. Copyright (c) 2020 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Revised BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices."; revision 2022-10-10 { description "Initial revision."; reference "RFC XXXX: Manufacturer Usage Description (MUD) (D)TLS Profiles for IoT Devices"; } augment "/ietf-mud:mud" { description "This adds a extension for a manufacturer to indicate whether (D)TLS profile is is supported by a device."; leaf is-tls-dtls-profile-supported { type boolean; default false; description "This value will equal 'true' if a device supports (D)TLS profile."; } } } <CODE ENDS>¶
6. Processing of the MUD (D)TLS Profile
The following text outlines the rules for a network security service (e.g., firewall) to follow to process the MUD (D)TLS Profile so as to avoid ossification:¶
-
If the (D)TLS parameter observed in a (D)TLS session is not specified in the MUD (D)TLS profile and the parameter is recognized by the firewall, it can identify unexpected (D)TLS usage, which can indicate the presence of unauthorized software or malware on an endpoint. The firewall can take several actions like block the (D)TLS session or raise an alert to quarantine and remediate the compromised device. For example, if the cipher suite TLS_RSA_WITH_AES_128_CBC_SHA in the ClientHello message is not specified in the MUD (D)TLS profile and the cipher suite is recognized by the firewall, it can identify unexpected TLS usage.¶
-
If the (D)TLS parameter observed in a (D)TLS session is not specified in the MUD (D)TLS profile and the (D)TLS parameter is not recognized by the firewall, it can ignore the unrecognized parameter and the correct behavior is not to block the (D)TLS session. The behaviour is functionally equivalent to the compliant TLS middlebox description in Section 9.3 of [RFC8446] to ignore all unrecognized cipher suites, extensions, and other parameters. For example, if the cipher suite TLS_CHACHA20_POLY1305_SHA256 in the ClientHello message is not specified in the MUD (D)TLS profile and the cipher suite is not recognized by the firewall, it can ignore the unrecognized cipher suite. This rule also ensures that the network security service will ignore the GREASE values advertised by TLS peers and interoperate with the implementations advertising GREASE values.¶
-
Deployments update at different rates, so an updated MUD (D)TLS profile may support newer parameters. If the firewall does not recognize the newer parameters, an alert should be triggered to the firewall vendor and the IoT device owner or administrator. A firewall must be readily updatable, so that when new parameters in the MUD (D)TLS profile are discovered that are not recognized by the firewall, it can be updated quickly. Most importantly, if the firewall is not readily updatable, its protection efficacy to identify emerging malware will decrease with time. For example, if the cipher suite TLS_AES_128_CCM_8_SHA256 specified in the MUD (D)TLS profile is not recognized by the firewall, an alert will be triggered. Similarly, if the (D)TLS version specified in the MUD file is not recognized by the firewall, an alert will be triggered.¶
7. MUD File Example
The example below contains (D)TLS profile parameters for a IoT device used to reach servers listening on port 443 using TCP transport. JSON encoding of YANG modelled data [RFC7951] is used to illustrate the example.¶
{ "ietf-mud:mud": { "mud-version": 1, "mud-url": "https://example.com/IoTDevice", "last-update": "2019-18-06T03:56:40.105+10:00", "cache-validity": 100, "extensions": [ "ietf-mud-tls" ], "ietf-mud-tls:is-tls-dtls-profile-supported": "true", "is-supported": true, "systeminfo": "IoT device name", "from-device-policy": { "access-lists": { "access-list": [ { "name": "mud-7500-profile" } ] } }, "ietf-access-control-list:acls": { "acl": [ { "name": "mud-7500-profile", "type": "ipv6-acl-type", "aces": { "ace": [ { "name": "cl0-frdev", "matches": { "ipv6": { "protocol": 6 }, "tcp": { "ietf-mud:direction-initiated": "from-device", "destination-port": { "operator": "eq", "port": 443 } }, "ietf-acl-tls:client-profile" : { "tls-dtls-profiles" : [ { "name" : "profile1", "supported-tls-versions" : ["tls13"], "cipher-suite" : [4865, 4866], "extension-types" : [10,11,13,16,24], "supported-groups" : [29] } ] }, "actions": { "forwarding": "accept" } } } ] } } ] } } }¶
The following illustrates the example scenarios for processing the above profile:¶
-
If the extension type "encrypt_then_mac" (code point 22) [RFC7366] in the ClientHello message is recognized by the firewall, it can identify unexpected TLS usage.¶
-
If the extension type "token_binding" (code point 24) [RFC8472] in the MUD (D)TLS profile is not recognized by the firewall, it can ignore the unrecognized extension. Because the extension type "token_binding" is specified in the profile, an alert will be triggered to the firewall vendor and the IoT device owner or administrator to notify the firewall is not up to date.¶
-
The two-byte values assigned by IANA for the cipher suites TLS_AES_128_GCM_SHA256 and TLS_AES_256_GCM_SHA384 are represented in decimal format.¶
8. Security Considerations
Security considerations in [RFC8520] need to be taken into consideration. The middlebox must adhere to the invariants discussed in Section 9.3 of [RFC8446] to act as a compliant proxy.¶
Although it is challenging for a malware to mimic the TLS behavior of various IoT device types and IoT device models from several manufacturers, malicious agents have a very low probability of using the same (D)TLS profile parameters as legitimate agents on the IoT device to evade detection. Network security services should also rely on contextual network data to detect false negatives. In order to detect such malicious flows, anomaly detection (deep learning techniques on network data) can be used to detect malicious agents using the same (D)TLS profile parameters as legitimate agent on the IoT device. In anomaly detection, the main idea is to maintain rigorous learning of "normal" behavior and where an "anomaly" (or an attack) is identified and categorized based on the knowledge about the normal behavior and a deviation from this normal behavior.¶
Please note that the security considerations mentioned in Section 3.7 of [RFC8407] are not applicable in this case because the YANG serialization is not intended to be accessed via NETCONF. However, for those who try to instantiate this model in a network element via the Network Configuration Protocol (NETCONF), all objects in each model in this document exhibit similar security characteristics as [RFC8519].¶
9. Privacy Considerations
Privacy considerations discussed in Section 16 of [RFC8520] to not reveal the MUD URL to an attacker need to be taken into consideration. The MUD URL can be stored in Trusted Execution Environment (TEE) for secure operation, enhanced data security, and prevent exposure to unauthorized software. The MUD URL MUST be encrypted and shared only with the authorized components in the network (see Section 1.5 and Section 1.8 of [RFC8520]) so that an on-path attacker cannot read the MUD URL and identify the IoT device. Otherwise, it provides the attacker with guidance on what vulnerabilities may be present on the IoT device. Note that while protecting the MUD URL is valuable as described above, a compromised IoT device may be susceptible to malware performing vulnerability analysis (and version mapping) of the legitimate software located in memory or on non-volatile storage (e.g., disk, NVRAM). However, the malware on the IoT device won't be able to establish a (D)TLS connection with the C&C server to reveal this information because the connection would be blocked by the network security service supporting this specification.¶
Full handshake inspection (Section 4.1) requires a (D)TLS proxy device which needs to decrypt traffic between the IoT device and its server(s). There is a tradeoff between privacy of the data carried inside (D)TLS (especially e.g., personally identifiable information and protected health information) and efficacy of endpoint security. It is strongly RECOMMENDED to avoid a (D)TLS proxy whenever possible. For example, an enterprise firewall administrator can configure the middlebox to bypass (D)TLS proxy functionality or payload inspection for connections destined to specific well-known services. Alternatively, a IoT device could be configured to reject all sessions that involve proxy servers to specific well-known services. In addition, mechanisms based on object security can be used by IoT devices to enable end-to-end security and the middlebox will not have any access to the packet data. For example, Object Security for Constrained RESTful Environments (OSCORE) [RFC8613] is a proposal that protects CoAP messages by wrapping them in the COSE format [RFC8152].¶
10. IANA Considerations
10.1. (D)TLS Profile YANG Modules
This document requests IANA to register the following URIs in the "ns" subregistry within the "IETF XML Registry" [RFC3688]:¶
URI: urn:ietf:params:xml:ns:yang:iana-tls-profile Registrant Contact: IANA. XML: N/A; the requested URI is an XML namespace.¶
URI: urn:ietf:params:xml:ns:yang:ietf-acl-tls Registrant Contact: IESG. XML: N/A; the requested URI is an XML namespace.¶
URI: urn:ietf:params:xml:ns:yang:ietf-mud-tls Registrant Contact: IESG. XML: N/A; the requested URI is an XML namespace.¶
IANA is requested to create an IANA-maintained YANG Module called "iana-tls-profile", based on the contents of Section 5.3, which will allow for new (D)TLS parameters and (D)TLS versions to be added to "client-profile". The registration procedure will be Expert Review, as defined by [RFC8126]. The designated expert allows new (D)TLS parameters to be added to the YANG Module provided they were added to the TLS and DTLS IANA registries and if the new (D)TLS parameters can be used by a middlebox to identify a MUD non-compliant (D)TLS behavior. The designated expert allows new (D)TLS version to be added to the YANG Module provided the new (D)TLS version specification is adopted by the TLS WG.¶
This document requests IANA to register the following YANG modules in the "YANG Module Names" subregistry [RFC6020] within the "YANG Parameters" registry.¶
name: iana-tls-profile namespace: urn:ietf:params:xml:ns:yang:iana-tls-profile maintained by IANA: Y prefix: ianatp reference: RFC XXXX¶
name: ietf-acl-tls namespace: urn:ietf:params:xml:ns:yang:ietf-acl-tls maintained by IANA: N prefix: ietf-acl-tls reference: RFC XXXX¶
name: ietf-mud-tls namespace: urn:ietf:params:xml:ns:yang:ietf-mud-tls maintained by IANA: N prefix: ietf-mud-tls reference: RFC XXXX¶
IANA is requested to create an the initial version of the IANA-maintained YANG Module called "iana-tls-profile", based on the contents of Section 5.3, which will allow for new (D)TLS parameters and (D)TLS versions to be added. IANA is requested to add this note:¶
-
tls-version and dtls-version values must not be directly added to the iana-tls-profile YANG module. They must instead be respectively added to the "ACL TLS Version Codes", and "ACL DTLS Version Codes" registries.¶
-
(D)TLS parameters must not be directly added to the iana-tls-profile YANG module. They must instead be added to the "ACL (D)TLS Parameters" registry.¶
When a 'tls-version' or 'dtls-version' value is respectively added to the "ACL TLS Version Codes" or "ACL DTLS Version Codes" registry, a new "enum" statement must be added to the iana-tls-profile YANG module. The following "enum" statement, and substatements thereof, should be defined:¶
- "enum":
- Replicates the label from the registry.¶
- "value":
- Contains the IANA-assigned value corresponding to the 'tls-version' or 'dtls-version'.¶
- "description":
- Replicates the description from the registry.¶
- "reference":
- Replicates the reference from the registry and adds the title of the document.¶
When a (D)TLS parameter is added to "ACL (D)TLS Parameters" registry, a new "type" statement must be added to the iana-tls-profile YANG module. The following "type" statement, and substatements thereof, should be defined:¶
- "derived type":
- Replicates the parameter name from the registry.¶
- "built-in type":
- Contains the built-in YANG type.¶
- "description":
- Replicates the description from the registry.¶
When the iana-tls-profile YANG module is updated, a new "revision" statement must be added in front of the existing revision statements.¶
IANA is requested to add this note to "ACL TLS Version Codes", "ACL DTLS Version Codes", and "ACL (D)TLS Parameters" registries:¶
-
When this registry is modified, the YANG module iana-tls-profile must be updated as defined in [RFCXXXX].¶
The registration procedure for "ietf-acl-tls" YANG module will be Specification Required, as defined by [RFC8126].¶
10.2. ACL TLS Version registry
IANA is requested to create a new registry titled "ACL TLS Version Codes". Codes in this registry are used as valid values of 'tls-version' parameter. Further assignments are to be made through Expert Review [RFC8126].¶
+-------+---------+-----------------+-----------+ | Value | Label | Description | Reference | | | | | | | | | | | +-------+---------+-----------------+-----------+ | 1 | tls12 | TLS Version 1.2 | [RFC5246] | +-------+---------+-----------------+-----------+ | 2 | tls13 | TLS Version 1.3 | [RFC8446] | +-------+---------+-----------------+-----------+¶
10.3. ACL DTLS version registry
IANA is requested to create a new registry titled "ACL DTLS Version Codes". Codes in this registry are used as valid values of 'dtls-version' parameter. Further assignments are to be made through Expert Review [RFC8126].¶
+-------+---------+----------------+-----------------------+ | Value | Label | Description | Reference | | | | | | | | | | | +-------+---------+----------------+-----------------------+ | 1 |dtls12 |DTLS Version 1.2| [RFC6347] | +-------+---------+----------------+-----------------------+ | 2 |dtls13 |DTLS Version 1.3| [RFC9147| | +-------+---------+----------------+-----------------------+¶
10.4. ACL (D)TLS Parameters registry
IANA is requested to create a new registry titled "ACL (D)TLS parameters".¶
The values for all the (D)TLS parameters in the registry are defined in the TLS and DTLS IANA registries (https://www.iana.org/assignments/tls-parameters/tls-parameters.txt and https://www.iana.org/assignments/tls-extensiontype-values/tls-extensiontype-values.txt) excluding the tls-version and dtls-version parameters. Further assignments are to be made through Expert Review [RFC8126]. The registry is initially populated with the following parameters:¶
+----------------------------+-------------+--------+---------------------------------------------+ | Parameter Name | YANG | JSON | | | | Type | Type | Description | | | | | | +----------------------------+-------------+--------+---------------------------------------------+ | extension-type | uint16 | Number | Extension type | +----------------------------+-------------+--------+---------------------------------------------+ | supported-group | uint16 | Number | Supported group | +----------------------------+-------------+--------+---------------------------------------------+ | signature-algorithm | uint16 | Number | Signature algorithm | +----------------------------+-------------+--------+---------------------------------------------+ | psk-key-exchange-mode | uint8 | Number | pre-shared key exchange mode | +----------------------------+-------------+--------+---------------------------------------------+ | application-protocol | string | String | Application protocol | +----------------------------+-------------+--------+---------------------------------------------+ | cert-compression-algorithm | uint16 | Number | Certificate compression algorithm | +----------------------------+-------------+--------+---------------------------------------------+ | cipher-algorithm | uint16 | Number | Cipher Suite | +----------------------------+-------------+--------+---------------------------------------------+ | tls-version | enumeration | String | TLS version | +----------------------------+-------------+--------+---------------------------------------------+ | dtls-version | enumeration | String | DTLS version | +----------------------------+-------------+--------+---------------------------------------------+¶
10.5. MUD Extensions registry
IANA is requested to create a new MUD Extension Name "ietf-mud-tls" in the MUD Extensions IANA registry https://www.iana.org/assignments/mud/mud.xhtml.¶
11. Acknowledgments
Thanks to Flemming Andreasen, Shashank Jain, Michael Richardson, Piyush Joshi, Eliot Lear, Harsha Joshi, Qin Wu, Mohamed Boucadair, Ben Schwartz, Eric Rescorla, Panwei William, Nick Lamb, Tom Petch, Paul Wouters and Nick Harper for the discussion and comments.¶
Thanks to Xufeng Liu for YANGDOCTOR review. Thanks to Linda Dunbar for SECDIR review.¶
12. References
12.1. Normative References
- [I-D.ietf-netconf-crypto-types]
- Watsen, K., "YANG Data Types and Groupings for Cryptography", Work in Progress, Internet-Draft, draft-ietf-netconf-crypto-types-28, , <https://datatracker.ietf.org/doc/html/draft-ietf-netconf-crypto-types-28>.
- [RFC2119]
- Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
- [RFC3688]
- Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, , <https://www.rfc-editor.org/info/rfc3688>.
- [RFC5246]
- Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2", RFC 5246, DOI 10.17487/RFC5246, , <https://www.rfc-editor.org/info/rfc5246>.
- [RFC6234]
- Eastlake 3rd, D. and T. Hansen, "US Secure Hash Algorithms (SHA and SHA-based HMAC and HKDF)", RFC 6234, DOI 10.17487/RFC6234, , <https://www.rfc-editor.org/info/rfc6234>.
- [RFC6347]
- Rescorla, E. and N. Modadugu, "Datagram Transport Layer Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347, , <https://www.rfc-editor.org/info/rfc6347>.
- [RFC8174]
- Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
- [RFC8446]
- Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, , <https://www.rfc-editor.org/info/rfc8446>.
- [RFC8519]
- Jethanandani, M., Agarwal, S., Huang, L., and D. Blair, "YANG Data Model for Network Access Control Lists (ACLs)", RFC 8519, DOI 10.17487/RFC8519, , <https://www.rfc-editor.org/info/rfc8519>.
- [RFC8520]
- Lear, E., Droms, R., and D. Romascanu, "Manufacturer Usage Description Specification", RFC 8520, DOI 10.17487/RFC8520, , <https://www.rfc-editor.org/info/rfc8520>.
- [RFC8701]
- Benjamin, D., "Applying Generate Random Extensions And Sustain Extensibility (GREASE) to TLS Extensibility", RFC 8701, DOI 10.17487/RFC8701, , <https://www.rfc-editor.org/info/rfc8701>.
- [RFC8879]
- Ghedini, A. and V. Vasiliev, "TLS Certificate Compression", RFC 8879, DOI 10.17487/RFC8879, , <https://www.rfc-editor.org/info/rfc8879>.
- [RFC9147]
- Rescorla, E., Tschofenig, H., and N. Modadugu, "The Datagram Transport Layer Security (DTLS) Protocol Version 1.3", RFC 9147, DOI 10.17487/RFC9147, , <https://www.rfc-editor.org/info/rfc9147>.
- [X690]
- ITU-T, "Information technology - ASN.1 encoding Rules: Specification of Basic Encoding Rules (BER), Canonical Encoding Rules (CER) and Distinguished Encoding Rules (DER)", ISO/IEC 8825-1:2002, .
12.2. Informative References
- [clear-as-mud]
- "Clear as MUD: Generating, Validating and Applying IoT Behaviorial Profiles", , <https://arxiv.org/pdf/1804.04358.pdf>.
- [cryto-vulnerability]
- Perez, B., "Exploiting the Windows CryptoAPI Vulnerability", , <https://media.defense.gov/2020/Jan/14/2002234275/-1/-1/0/CSA-WINDOWS-10-CRYPT-LIB-20190114.PDF>.
- [I-D.ietf-tls-esni]
- Rescorla, E., Oku, K., Sullivan, N., and C. A. Wood, "TLS Encrypted Client Hello", Work in Progress, Internet-Draft, draft-ietf-tls-esni-17, , <https://datatracker.ietf.org/doc/html/draft-ietf-tls-esni-17>.
- [I-D.ietf-uta-tls13-iot-profile]
- Tschofenig, H., Fossati, T., and M. Richardson, "TLS/DTLS 1.3 Profiles for the Internet of Things", Work in Progress, Internet-Draft, draft-ietf-uta-tls13-iot-profile-08, , <https://datatracker.ietf.org/doc/html/draft-ietf-uta-tls13-iot-profile-08>.
- [malware]
- Anderson, B., Paul, S., and D. McGrew, "Deciphering Malware's use of TLS (without Decryption)", , <https://arxiv.org/abs/1607.01639>.
- [malware-doh]
- Cimpanu, C., "First-ever malware strain spotted abusing new DoH (DNS over HTTPS) protocol", , <https://www.zdnet.com/article/first-ever-malware-strain-spotted-abusing-new-doh-dns-over-https-protocol/>.
- [malware-tls]
- Anderson, B. and D. McGrew, "TLS Beyond the Browser: Combining End Host and Network Data to Understand Application Behavior", , <https://dl.acm.org/citation.cfm?id=3355601>.
- [RFC5869]
- Krawczyk, H. and P. Eronen, "HMAC-based Extract-and-Expand Key Derivation Function (HKDF)", RFC 5869, DOI 10.17487/RFC5869, , <https://www.rfc-editor.org/info/rfc5869>.
- [RFC6020]
- Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/info/rfc6020>.
- [RFC6066]
- Eastlake 3rd, D., "Transport Layer Security (TLS) Extensions: Extension Definitions", RFC 6066, DOI 10.17487/RFC6066, , <https://www.rfc-editor.org/info/rfc6066>.
- [RFC7301]
- Friedl, S., Popov, A., Langley, A., and E. Stephan, "Transport Layer Security (TLS) Application-Layer Protocol Negotiation Extension", RFC 7301, DOI 10.17487/RFC7301, , <https://www.rfc-editor.org/info/rfc7301>.
- [RFC7366]
- Gutmann, P., "Encrypt-then-MAC for Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS)", RFC 7366, DOI 10.17487/RFC7366, , <https://www.rfc-editor.org/info/rfc7366>.
- [RFC7525]
- Sheffer, Y., Holz, R., and P. Saint-Andre, "Recommendations for Secure Use of Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS)", RFC 7525, DOI 10.17487/RFC7525, , <https://www.rfc-editor.org/info/rfc7525>.
- [RFC7925]
- Tschofenig, H., Ed. and T. Fossati, "Transport Layer Security (TLS) / Datagram Transport Layer Security (DTLS) Profiles for the Internet of Things", RFC 7925, DOI 10.17487/RFC7925, , <https://www.rfc-editor.org/info/rfc7925>.
- [RFC7951]
- Lhotka, L., "JSON Encoding of Data Modeled with YANG", RFC 7951, DOI 10.17487/RFC7951, , <https://www.rfc-editor.org/info/rfc7951>.
- [RFC8126]
- Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, , <https://www.rfc-editor.org/info/rfc8126>.
- [RFC8152]
- Schaad, J., "CBOR Object Signing and Encryption (COSE)", RFC 8152, DOI 10.17487/RFC8152, , <https://www.rfc-editor.org/info/rfc8152>.
- [RFC8340]
- Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, , <https://www.rfc-editor.org/info/rfc8340>.
- [RFC8407]
- Bierman, A., "Guidelines for Authors and Reviewers of Documents Containing YANG Data Models", BCP 216, RFC 8407, DOI 10.17487/RFC8407, , <https://www.rfc-editor.org/info/rfc8407>.
- [RFC8447]
- Salowey, J. and S. Turner, "IANA Registry Updates for TLS and DTLS", RFC 8447, DOI 10.17487/RFC8447, , <https://www.rfc-editor.org/info/rfc8447>.
- [RFC8472]
- Popov, A., Ed., Nystroem, M., and D. Balfanz, "Transport Layer Security (TLS) Extension for Token Binding Protocol Negotiation", RFC 8472, DOI 10.17487/RFC8472, , <https://www.rfc-editor.org/info/rfc8472>.
- [RFC8484]
- Hoffman, P. and P. McManus, "DNS Queries over HTTPS (DoH)", RFC 8484, DOI 10.17487/RFC8484, , <https://www.rfc-editor.org/info/rfc8484>.
- [RFC8576]
- Garcia-Morchon, O., Kumar, S., and M. Sethi, "Internet of Things (IoT) Security: State of the Art and Challenges", RFC 8576, DOI 10.17487/RFC8576, , <https://www.rfc-editor.org/info/rfc8576>.
- [RFC8613]
- Selander, G., Mattsson, J., Palombini, F., and L. Seitz, "Object Security for Constrained RESTful Environments (OSCORE)", RFC 8613, DOI 10.17487/RFC8613, , <https://www.rfc-editor.org/info/rfc8613>.
- [RFC9462]
- Pauly, T., Kinnear, E., Wood, C. A., McManus, P., and T. Jensen, "Discovery of Designated Resolvers", RFC 9462, DOI 10.17487/RFC9462, , <https://www.rfc-editor.org/info/rfc9462>.
- [RFC9463]
- Boucadair, M., Ed., Reddy.K, T., Ed., Wing, D., Cook, N., and T. Jensen, "DHCP and Router Advertisement Options for the Discovery of Network-designated Resolvers (DNR)", RFC 9463, DOI 10.17487/RFC9463, , <https://www.rfc-editor.org/info/rfc9463>.
- [X501]
- "Information Technology - Open Systems Interconnection - The Directory: Models", ITU-T X.501, .