Internet Engineering Task Force H. Chen
Internet-Draft R. Li
Intended status: Experimental Huawei Technologies
Expires: June 25, 2016 A. Retana
Y. Yang
Cisco Systems, Inc.
V. Liu
China Mobile
M. Toy
Comcast
December 23, 2015
OSPF Topology-Transparent Zone
draft-ietf-ospf-ttz-02.txt
Abstract
This document presents a topology-transparent zone in a domain. A
topology-transparent zone comprises a group of routers and a number
of links connecting these routers. Any router outside of the zone is
not aware of the zone. The information about the links and routers
inside the zone is not distributed to any router outside of the zone.
Any link state change such as a link down inside the zone is not seen
by any router outside of the zone.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 25, 2016.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
Chen, et al. Expires June 25, 2016 [Page 1]
Internet-Draft Topology-Transparent Zone December 2015
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Conventions Used in This Document . . . . . . . . . . . . . . 4
4. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Topology-Transparent Zone . . . . . . . . . . . . . . . . . . 5
5.1. Overview of Topology-Transparent Zone . . . . . . . . . . 5
5.2. Some Details on TTZ . . . . . . . . . . . . . . . . . . . 5
6. Extensions to OSPF Protocols . . . . . . . . . . . . . . . . . 6
7. Constructing LSAs for TTZ . . . . . . . . . . . . . . . . . . 10
8. Establishing Adjacencies . . . . . . . . . . . . . . . . . . . 11
8.1. Discover TTZ Neighbor over Normal Adjacency . . . . . . . 11
8.2. Establishing TTZ Adjacencies . . . . . . . . . . . . . . . 12
8.3. Adjacency between TTZ Edge and TTZ External Router . . . . 12
9. Distribution of LSAs . . . . . . . . . . . . . . . . . . . . . 13
9.1. Distribution of LSAs within TTZ . . . . . . . . . . . . . 13
9.2. Distribution of LSAs through TTZ . . . . . . . . . . . . . 13
10. Computation of Routing Table . . . . . . . . . . . . . . . . . 13
11. Operations . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11.1. Configuring TTZ . . . . . . . . . . . . . . . . . . . . . 14
11.2. Smooth Migration to TTZ . . . . . . . . . . . . . . . . . 14
11.3. Adding a Router into TTZ . . . . . . . . . . . . . . . . . 15
12. Prototype Implementation . . . . . . . . . . . . . . . . . . . 15
12.1. What are Implemented and Tested . . . . . . . . . . . . . 16
12.2. Implementation Experience . . . . . . . . . . . . . . . . 17
13. Security Considerations . . . . . . . . . . . . . . . . . . . 17
14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 17
15. Contributors and Other Authors . . . . . . . . . . . . . . . . 18
16. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 19
17. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19
17.1. Normative References . . . . . . . . . . . . . . . . . . . 19
17.2. Informative References . . . . . . . . . . . . . . . . . . 20
Appendix A. Constants for LSA Distribution . . . . . . . . . . . 20
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 20
Chen, et al. Expires June 25, 2016 [Page 2]
Internet-Draft Topology-Transparent Zone December 2015
1. Introduction
The number of routers in a network becomes larger and larger as the
Internet traffic keeps growing. Through splitting the network into
multiple areas, we can extend the network further. However, there
are a number of issues when a network is split further into more
areas.
At first, dividing a network from one area into multiple areas or
from a number of existing areas to even more areas is a very
challenging and time consuming task since it is involved in
significant network architecture changes. Considering the one area
case, originally the network has only one area, which is the
backbone. This original backbone area will be split into a new
backbone and a number of non backbone areas. In general, each of the
non backbone areas is connected to the new backbone area through the
area border routers between the non backbone and the backbone area.
There is not any direct connection between any two non backbone
areas. Each area border router summarizes the topology of its
attached non backbone area for transmission on the backbone area, and
hence to all other area border routers.
Secondly, the services carried by the network may be interrupted
while the network is being split from one area into multiple areas or
from a number of existing areas into even more areas.
Furthermore, it is complex for a Multi-Protocol Label Switching
(MPLS) Traffic Engineering (TE) Label Switching Path (LSP) crossing
multiple areas to be setup. In one option, a TE path crossing
multiple areas is computed by using collaborating Path Computation
Elements (PCEs) [RFC5441] through the PCE Communication Protocol
(PCEP)[RFC5440], which is not easy to configure by operators since
the manual configuration of the sequence of domains is required.
Although this issue can be addressed by using the Hierarchical PCE,
this solution may further increase the complexity of network design.
Especially, the current PCE standard method may not guarantee that
the path found is optimal.
This document presents a topology-transparent zone in an area and
describes extensions to OSPF for supporting the topology-transparent
zone, which is scalable and resolves the issues above.
A topology-transparent zone comprises a group of routers and a number
of links connecting these routers. Any router outside of the zone is
not aware of the zone. The information about the links and routers
inside the zone is not distributed to any router outside of the zone.
Any link state change such as a link down inside the zone is not seen
by any router outside of the zone.
Chen, et al. Expires June 25, 2016 [Page 3]
Internet-Draft Topology-Transparent Zone December 2015
2. Terminology
TTZ internal link: a link between two TTZ adjacent routers in a same
TTZ.
TTZ external link: a link between a TTZ edge router and a router
outside of the TTZ.
TTZ internal router: a router in a TTZ whose adjacent routers are in
the same TTZ.
TTZ external router: a router outside of a TTZ without any TTZ
internal link.
TTZ edge router: a router in a TTZ that has one (or more) adjacent
routers which belong to the same TTZ, and one (or more) adjacent
routers which do not belong to the TTZ.
3. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119.
4. Requirements
Topology-Transparent Zone (TTZ) may be deployed for resolving some
critical issues in existing networks and future networks. The
requirements for TTZ are listed as follows:
o Routers outside a TTZ MUST NOT require any changes to operate with
the TTZ.
o A TTZ MUST be in an area.
o A TTZ MUST hide the topology of the TTZ from any router outside of
the TTZ.
o Users SHOULD be able to easily set up an end to end service
crossing TTZs.
o The configuration for a TTZ in a network SHOULD be minimum.
o The changes on the existing protocols for supporting TTZ SHOULD be
minimum.
Chen, et al. Expires June 25, 2016 [Page 4]
Internet-Draft Topology-Transparent Zone December 2015
5. Topology-Transparent Zone
5.1. Overview of Topology-Transparent Zone
A Topology-Transparent Zone (TTZ) is identified by an Identifier
(ID), and it includes a group of routers and a number of links
connecting the routers. A TTZ is in an OSPF area.
The ID of a TTZ or TTZ ID is a 32-bit number that is unique for
identifying an entity such as a node in an OSPF domain. It is not
zero in general.
In addition to having the functions of an OSPF area, an OSPF TTZ
makes some improvements on an OSPF area, which include:
o An OSPF TTZ is virtualized as the TTZ edges fully connected.
o An OSPF TTZ receives the link state information about the topology
outside of the TTZ, stores the information in the TTZ and floods
the information through the TTZ to the routers outside of the TTZ.
5.2. Some Details on TTZ
The figure below shows an area containing a TTZ: TTZ 600.
TTZ 600
\
\ ^~^~^~^~^~^~^~^~^~^~^~^~
( )
===[R15]========(==[R61]------------[R63]==)======[R29]===
|| ( | \ / | ) ||
|| ( | \ / | ) ||
|| ( | \ / | ) ||
|| ( | ___\ / | ) ||
|| ( | / [R71] | ) ||
|| ( | [R73] / \ | ) ||
|| ( | / \ | ) ||
|| ( | / \ | ) ||
|| ( | / \ | ) ||
===[R17]========(==[R65]------------[R67]==)======[R31]===
\\ (// \\) //
|| //v~v~v~v~v~v~v~v~v~v~v~\\ ||
|| // \\ ||
|| // \\ ||
\\ // \\ //
======[R23]==============================[R25]=====
// \\
// \\
Chen, et al. Expires June 25, 2016 [Page 5]
Internet-Draft Topology-Transparent Zone December 2015
The area comprises routers R15, R17, R23, R25, R29 and R31. It also
contains TTZ 600, which comprises routers R61, R63, R65, R67, R71 and
R73, and the links connecting them.
There are two types of routers in a TTZ: TTZ internal and TTZ edge
routers. TTZ 600 has four TTZ edge routers R61, R63, R65 and R67.
Each TTZ edge router is connected to at least one router outside of
TTZ 600. For instance, router R61 is a TTZ edge router since it is
connected to router R15, which is outside of TTZ 600.
In addition, TTZ 600 comprises two TTZ internal routers R71 and R73.
A TTZ internal router is not connected to any router outside of the
TTZ. For instance, router R71 is a TTZ internal router since it is
not connected to any router outside of TTZ 600. It is just connected
to routers R61, R63, R65, R67 and R73 in the TTZ.
A TTZ hides the internal topology of the TTZ from the outside. It
does not directly distribute any internal information about the TTZ
to a router outside of the TTZ.
For instance, TTZ 600 does not send the information about TTZ
internal router R71 to any router outside of TTZ 600; it does not
send the information about the link between TTZ router R61 and R65 to
any router outside of TTZ 600.
In order to create a TTZ, we may assign the same TTZ ID to the TTZ
edge routers and identify the TTZ internal links on them through CLI.
In addition, we assign the TTZ ID to every TTZ internal router which
indicates that every link of the router is a TTZ internal link.
From a router outside of the TTZ, a TTZ is seen as a group of routers
fully connected. For instance, router R15 in the figure above, which
is outside of TTZ 600, sees TTZ 600 as a group of TTZ edge routers:
R61, R63, R65 and R67, which are fully connected.
In addition, a router outside of the TTZ sees TTZ edge routers having
normal connections to the routers outside of the TTZ. For example,
router R15 sees four TTZ edge routers R61, R63, R65 and R67, which
have the normal connections to R15, R29, R17 and R23, R25 and R31
respectively.
6. Extensions to OSPF Protocols
The link state information about a TTZ includes router LSAs and
network LSAs. Router LSAs can be contained and distributed in opaque
LSAs [RFC5250] within the TTZ. Some control information on a TTZ can
also be contained and distributed in opaque LSAs within the TTZ.
Chen, et al. Expires June 25, 2016 [Page 6]
Internet-Draft Topology-Transparent Zone December 2015
These opaque LSAs are called TTZ opaque LSAs or TTZ LSAs for short.
The following is a general form of a TTZ LSA. It has an LS type =
10/9 and TTZ-LSA-Type, and contains a number of TLVs.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS age | Options | LS Type = 10/9|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TTZ-LSA-type(5)| Instance ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Advertising Router |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS checksum | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ TLVs ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Where TTZ-LSA-type is 5, the exact number for it is to be assigned by
IANA.
There are three top-level TLVs defined: TTZ ID TLV, TTZ Router TLV,
and TTZ Options TLV. A TTZ LSA of LS Type 10 contains a mandatory
TTZ ID TLV, which is followed by one of the other top-level TLVs.
A TTZ LSA containing a TTZ Router TLV is called TTZ Router LSA. A
TTZ LSA containing a TTZ Options TLV is called TTZ Control LSA.
A TTZ ID TLV has the following format. It contains a TTZ ID and some
flags.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTZ-ID-TLV-type (1) | Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTZ ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 |E|Z|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
E = 1: Indicating a router is a TTZ Edge router
Z = 1: Indicating a router has migrated to TTZ
Chen, et al. Expires June 25, 2016 [Page 7]
Internet-Draft Topology-Transparent Zone December 2015
When a TTZ router originates a TTZ LSA containing a TTZ ID TLV, it
sets flag E to 1 in the TTZ ID TLV if it is a TTZ edge router, and to
0 if it is a TTZ internal router. It sets flag Z to 1 after it has
migrated to TTZ.
The format of a TTZ Router TLV is as follows. It contains the
contents of a router LSA.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTZ-RT-TLV-type (2) | TLV-Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 |V|E|B| 0 | # links |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link Data |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | # TOS | metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
For a router link, the existing eight bit Type field for a router
link is split into two fields as follows:
0 1 2 3 4 5 6 7
+---+---+---+---+---+---+---+---+
| I | Type-1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
I bit flag:
1: Router link is a TTZ internal link.
0: Router link is a TTZ external link.
Type-1: The kind of the link.
For a link inside a TTZ, I bit flag is set to one, indicating that
this link is a TTZ internal link. For a link connecting to a router
outside of a TTZ from a TTZ edge router, I bit flag is set to zero,
indicating that this link is a TTZ external link.
The value of Type-1 is 1, 2, 3, or 4, which indicates that the kind
of a link being described is a point-to-point connection to another
router, a connection to a transit network, a connection to a stub
network, or a virtual link respectively.
The format of TTZ Options TLV is as follows.
Chen, et al. Expires June 25, 2016 [Page 8]
Internet-Draft Topology-Transparent Zone December 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTZ-OP-TLV-type (3) | Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|T|M|N|R| 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
T = 1: Distributing TTZ Topology Information for Migration
M = 1: Migrating to TTZ
N = 1: Distributing Normal Topology Information for Rollback
R = 1: Rolling back from TTZ
Flags T, M, N and R are exclusive. When one of them is set to 1, the
others MUST be set to 0.
After a user triggers a TTZ router in a way such as issuing a CLI
command to distribute TTZ topology information, the TTZ router
originates a TTZ Control LSA having a TTZ Options TLV with flag T set
to 1. It also originates its TTZ router LSA. When another TTZ
router receives the LSA with T = 1, it originates its TTZ router LSA
as needed.
After a user asks a TTZ router in a way such as a CLI command to
migrate to TTZ, the TTZ router originates a TTZ Control LSA having a
TTZ Options TLV with flag M set to 1 and migrates to TTZ. When
another TTZ router receives the LSA with M = 1, it also migrates to
TTZ.
After a user triggers a TTZ router to distribute normal topology
information, the TTZ router originates a TTZ Control LSA having a TTZ
Options TLV with flag N set to 1. It also distributes its normal
LSAs such as its normal router LSA and stops distributing its other
TTZ LSAs. When another TTZ router receives the LSA with N = 1, it
distributes its normal LSAs and stops distributing its TTZ LSAs.
After a user asks a TTZ router to roll back from TTZ, the TTZ router
originates a TTZ Control LSA having a TTZ Options TLV with flag R set
to 1 and rolls back from TTZ. When another TTZ router receives the
LSA with R = 1, it also rolls back from TTZ.
If two CLI trigger commands are issued on a TTZ router, two TTZ
Control LSAs having a same instance ID are originated by the TTZ
router.
A TTZ LSA of LS Type 9 with a TTZ ID TLV below is used to discover a
TTZ neighbor.
Chen, et al. Expires June 25, 2016 [Page 9]
Internet-Draft Topology-Transparent Zone December 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS age | Options | LS Type = 9 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TTZ-LSA-type(5)| Instance ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Advertising Router |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS checksum | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ TTZ ID TLV ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
7. Constructing LSAs for TTZ
The LSAs for representing a TTZ include TTZ router LSAs and normal
router LSAs for virtualizing the TTZ.
A TTZ router LSA generated by a TTZ edge router has a TTZ ID TLV and
a TTZ Router TLV. The former includes the ID of the TTZ to which the
router belongs and flag E set to 1, which indicates the originator of
the LSA is a TTZ Edge router. The latter contains the links to the
router.
A TTZ router LSA generated by a TTZ internal router has a TTZ ID TLV
containing the ID of the TTZ to which the router belongs and flag E
set to 0, which indicates the originator of the LSA is a TTZ internal
router. This LSA implies that all the links connected to the router
are TTZ internal links. In other words, all the router links in the
normal router LSA generated by the TTZ internal router are TTZ
internal links. Thus a TTZ internal router can choose one of two
options: 1) generating a TTZ router LSA with a TTZ ID TLV and a TTZ
Router TLV and 2) generating its normal router LSA and a TTZ router
LSA with just a TTZ ID TLV. These two options are compatible.
After receiving a trigger to migrate to TTZ such as a TTZ Control LSA
with flag M = 1, a TTZ edge router originates a normal router LSA for
virtualizing a TTZ, which comprises three groups of links in general.
The first group are the router links connecting the TTZ external
routers. These router links are normal router links. There is a
router link for every adjacency between this TTZ edge router and a
Chen, et al. Expires June 25, 2016 [Page 10]
Internet-Draft Topology-Transparent Zone December 2015
TTZ external router.
The second group are the "virtual" router links. For each of the
other TTZ edge routers, there is a point-to-point router link to it.
The cost of the link is the cost of the shortest path from this TTZ
edge router to it within the TTZ.
In addition, the LSA may contain a third group of links, which are
stub links for other destinations inside the TTZ. They may be the
loopback addresses to be accessed by a node outside of the TTZ.
To migrate to TTZ smoothly, a TTZ edge router virtualizes the TTZ in
two steps. At first, the router updates its normal router LSA by
adding a point-to-point link to each of the other edge routers of the
TTZ and a stub link for each of the loopback addresses in the TTZ to
be leaked. And then it removes the links configured as TTZ links
from its updated router LSA after sending its updated router LSA and
receiving the updated router LSAs originated by the other TTZ edge
routers for MaxLSADistTime or after sending its updated router LSA
for MaxLSAGenDistTime.
8. Establishing Adjacencies
This section describes the adjacencies in some different cases.
8.1. Discover TTZ Neighbor over Normal Adjacency
For two routers A and B connected by a P2P link and having a normal
adjacency, they discover TTZ each other through a TTZ LSA of LS Type
9 with a TTZ ID TLV. We call this LSA D-LSA for short. If two ends
of the link have the same TTZ ID, A and B are TTZ neighbors. The
following is a sequence of events related to TTZ.
A B
Configure TTZ Configure TTZ
D-LSA (TTZ-ID=100)
---------------------------> Same TTZ ID
A is B's TTZ Neighbor
D-LSA (TTZ-ID=100)
Same TTZ ID <---------------------------
B is A's TTZ Neighbor
A sends B a D-LSA with TTZ-ID after the TTZ is configured on it. B
sends A a D-LSA with TTZ-ID after the TTZ is configured on it. When
A receives the D-LSA from B and determines they have the same TTZ ID,
B is A's TTZ neighbor. When B receives the D-LSA from A and
Chen, et al. Expires June 25, 2016 [Page 11]
Internet-Draft Topology-Transparent Zone December 2015
determines they have the same TTZ ID, A is B's TTZ neighbor.
For a number of routers connected through a broadcast link and having
normal adjacencies among them, they also discover TTZ each other
through D-LSAs. The DR for the link "forms" TTZ adjacency with each
of the other routers if all the routers attached to the link have the
same TTZ ID configured on the connections to the link. Otherwise,
the DR does not "form" any TTZ adjacency with any router attached to
the link.
8.2. Establishing TTZ Adjacencies
When a router (say A) is connected via a P2P link to another router
(say B) and there is not any adjacency between them over the link, a
user configures TTZ on two ends of the link to form a TTZ adjacency.
They start to discover TTZ each other through D-LSAs in the same way
as described above after the normal adjacency is formed.
For a number of routers connected through a broadcast link and having
no adjacency among them, they start to form TTZ adjacencies after TTZ
is configured on the link. While forming adjacencies, they discover
TTZ each other through D-LSAs in the same way as described above
after the normal adjacency is formed.
8.3. Adjacency between TTZ Edge and TTZ External Router
For an edge router in a TTZ, it forms an adjacency with any TTZ
external router that has a connection with it.
When the edge router synchronizes its link state database with the
TTZ external router, it sends the TTZ external router the information
about all the LSAs except for the LSAs belonging to the TTZ that are
hidden from any router outside of the TTZ.
At the end of the link state database synchronization, the edge
router originates its own router LSA for virtualizing the TTZ and
sends this LSA to the TTZ external router.
From the point of view of the TTZ external router, which is outside
of the TTZ, it sees the other end as a normal router and forms the
adjacency in the same way as a normal router. It is not aware of
anything about its neighboring TTZ. From the LSAs related to the TTZ
edge router in the other end, it knows that the TTZ edge router is
connected to each of the other TTZ edge routers and some routers
outside of the TTZ.
Chen, et al. Expires June 25, 2016 [Page 12]
Internet-Draft Topology-Transparent Zone December 2015
9. Distribution of LSAs
LSAs can be divided into a couple of classes according to their
distributions. The first class of LSAs is distributed within a TTZ.
The second is distributed through a TTZ.
9.1. Distribution of LSAs within TTZ
Any LSA about a link state in a TTZ is distributed within the TTZ.
It is not distributed to any router outside of the TTZ. For example,
a router LSA generated for a router in a TTZ is distributed within
the TTZ and not distributed to any router outside of the TTZ.
Any network LSA generated for a broadcast or NBMA network in a TTZ is
distributed in the TTZ and not sent to a router outside of the TTZ.
Any opaque LSA generated for a TTZ internal TE link is distributed
within the TTZ and not distributed to any router outside of the TTZ.
After migrating to TTZ, every edge router of a TTZ MUST NOT
distribute any LSA about a link state in the TTZ to any router
outside of the TTZ.
For any TTZ LSA originated by a router within the TTZ, every edge
router of the TTZ MUST NOT distribute it to any router outside of the
TTZ.
9.2. Distribution of LSAs through TTZ
Any LSA about a link state outside of a TTZ received by an edge
router of the TTZ is distributed through the TTZ. For example, when
an edge router of a TTZ receives an LSA from a router outside of the
TTZ, it floods it to its neighboring routers both inside the TTZ and
outside of the TTZ. This LSA may be any LSA such as a router LSA
that is distributed in a domain.
The routers in the TTZ continue to flood the LSA. When another edge
router of the TTZ receives the LSA, it floods the LSA to its
neighboring routers both outside of the TTZ and inside the TTZ.
10. Computation of Routing Table
When a router migrates to TTZ, the computation of the routing table
on the router is the same as that described in RFC 2328, with one
exception. The router in a TTZ ignores the router LSAs generated by
the TTZ edge routers for virtualizing the TTZ. It computes routes
through using the TTZ topology and the topology outside of the TTZ.
Chen, et al. Expires June 25, 2016 [Page 13]
Internet-Draft Topology-Transparent Zone December 2015
11. Operations
11.1. Configuring TTZ
This section proposes some options for configuring a TTZ.
1. Configuring TTZ on Every Link in TTZ
If every link in a TTZ is configured with a same TTZ ID as a TTZ
link, the TTZ is determined. A router with some TTZ links and some
normal links is a TTZ edge router. A router with only TTZ links is a
TTZ internal router.
2. Configuring TTZ on Every Router in TTZ
We may configure a same TTZ ID on every router in the TTZ, and on
every edge router's links connecting to the routers in the TTZ.
A router configured with the TTZ ID on some of its links is a TTZ
edge router. A router configured with the TTZ ID only is a TTZ
internal router. All the links on a TTZ internal router are TTZ
links. This option is simpler than the above one.
11.2. Smooth Migration to TTZ
For a group of routers and a number of links connecting the routers
in an area, making them transfer to work as a TTZ without any service
interruption takes a few of steps or stages.
At first, a user configures the TTZ feature on every router in the
TTZ. In this stage, a router does not originate its TTZ router LSA.
It will discover its TTZ neighbors.
Secondly, after configuring the TTZ, a user issues a CLI command on
one router in the TTZ, which triggers every router in the TTZ to
generate and distribute TTZ information among the routers in the TTZ.
When the router receives the command, it originates a TTZ control LSA
with T=1 (indicating TTZ information generation and distribution for
migration). It also originates its TTZ router LSA, and distributes
the LSA to its TTZ neighbors. When a router in the TTZ receives the
LSA with T=1, it originates its TTZ router LSA. In this stage, every
router in the TTZ has dual roles. One is to function as a normal
router. The other is to generate and distribute TTZ information.
Thirdly, a user checks whether every router in the TTZ is ready for
migration to TTZ. A router in the TTZ is ready after it has received
all the necessary information from all the routers in the TTZ. This
information may be displayed on a router through a CLI command.
Chen, et al. Expires June 25, 2016 [Page 14]
Internet-Draft Topology-Transparent Zone December 2015
And then a user activates the TTZ through using a CLI command such as
migrate to TTZ on one router in the TTZ. The router migrates to TTZ,
generates and distributes a TTZ control LSA with M = 1 (indicating
Migrating to TTZ) after it receives the command.
After a router in the TTZ receives the TTZ control LSA with M = 1, it
also migrates to TTZ. Thus, activating the TTZ on one TTZ router
makes every router in the TTZ migrate to TTZ, which computes routes
through using the TTZ topology and the topology outside of the TTZ.
For an edge router of the TTZ, migrating to work as a TTZ router
comprises generating a router LSA to virtualize the TTZ and flooding
this LSA to all its neighboring routers in two steps described in
section 7.
In normal operations for migration to TTZ and rollback from TTZ, a
user issues a series of commands according to certain procedures. In
an abnormal case, for example two conflict commands are issued on two
TTZ routers in a TTZ at the same time, a TTZ router gives a warning
when it detects the abnormal case.
11.3. Adding a Router into TTZ
When a non TTZ router (say R1) is connected via a P2P link to a TTZ
router (say T1) working as TTZ and there is a normal adjacency
between them over the link, a user can configure TTZ on two ends of
the link to add R1 into the TTZ to which T1 belongs. They discover
TTZ each other in the same way as described in section 8.
When a number of non TTZ routers are connected via a broadcast link
to a TTZ router (say T1) working as TTZ and there are normal
adjacencies among them, a user configures TTZ on the connection to
the link on every router to add the non TTZ routers into the TTZ to
which T1 belongs. The DR for the link "forms" TTZ adjacency with
each of the other routers if all the routers have the same TTZ ID
configured on the connections to the link.
When a router (say R1) is connected via a P2P link to a TTZ router
(say T1) and there is not any adjacency between them over the link, a
user can configure TTZ on two ends of the link to add R1 into the TTZ
to which T1 belongs. R1 and T1 will form an adjacency in the same
way as described in section 8.
12. Prototype Implementation
Chen, et al. Expires June 25, 2016 [Page 15]
Internet-Draft Topology-Transparent Zone December 2015
12.1. What are Implemented and Tested
1. CLI Commands for TTZ
The CLIs implemented and tested include:
o the CLIs of the simpler option for configuring TTZ, and
o the CLIs for controlling migration to TTZ.
2. Extensions to OSPF Protocols for TTZ
All the extensions defined in section "Extensions to OSPF Protocols"
are implemented and tested except for rolling back from TTZ. The
testing results illustrate:
o A TTZ is virtualized to outside as its edge routers fully
connected. Any router outside of the TTZ sees the edge routers
(as normal routers) connecting each other and to some other
routers.
o The link state information about the routers and links inside the
TTZ is contained within the TTZ. It is not distributed to any
router outside of the TTZ.
o TTZ is transparent. From a router inside a TTZ, it sees the
topology (link state) outside of the TTZ. From a router outside
of the TTZ, it sees the topology beyond the TTZ. The link state
information outside of the TTZ is distributed through the TTZ.
o TTZ is backward compatible. Any router outside of a TTZ does not
need to support or know TTZ.
3. Smooth Migration to TTZ
The procedures and related protocol extensions for smooth migration
to TTZ are implemented and tested. The testing results show:
o A part of an area is smoothly migrated to a TTZ without any
routing disruptions. The routes on every router are stable while
the part of the area is being migrated to the TTZ.
o Migration to TTZ is very easy to operate.
4. Add a Router to TTZ
Adding a router into TTZ is implemented and tested. The testing
results illustrate:
Chen, et al. Expires June 25, 2016 [Page 16]
Internet-Draft Topology-Transparent Zone December 2015
o A router can be easily added into a TTZ and becomes a TTZ router.
o The router added into the TTZ is not seen on any router outside of
the TTZ, but it is a part of the TTZ.
5. Leak TTZ Loopbacks Outside
Leaking loopback addresses in a TTZ to routers outside of the TTZ is
implemented and tested. The testing results illustrate:
o The loopback addresses inside the TTZ are distributed to the
routers outside of the TTZ.
o The loopback addresses are accessible from a router outside of the
TTZ.
12.2. Implementation Experience
The implementation of TTZ is relatively easy compared to other
features of OSPF. Re-using the existing OSPF code along with
additional simple logic does the work. A couple of engineers started
to work on implementing the TTZ from the middle of June, 2014 and
finished coding it just before IETF 90. After some testing and bug
fixes, it works as expected.
In our implementation, the link state information in a TTZ opaque LSA
is stored in the same link state database as the link state
information in a normal LSA. For each TTZ link in the TTZ opaque LSA
stored, there is an additional flag, which is used to differentiate
between a TTZ link and a Normal link.
Before migration to TTZ, every router in the TTZ computes its routing
table using the normal links. After migration to TTZ, every router
in the TTZ computes its routing table using the TTZ links and normal
links. In the case that there are one TTZ link and one normal link
to select, the TTZ link is used.
13. Security Considerations
The mechanism described in this document does not raise any new
security issues for the OSPF protocols.
14. IANA Considerations
Under Registry Name: Opaque Link-State Advertisements (LSA) Option
Types [RFC5250], IANA is requested to assign a new Opaque type
Chen, et al. Expires June 25, 2016 [Page 17]
Internet-Draft Topology-Transparent Zone December 2015
registry value for Topology-Transparent Zone (TTZ) LSA as follows:
+====================+===============+=======================+
| Registry Value | Opaque Type | reference |
+====================+===============+=======================+
| 5 | TTZ LSA | This document |
+--------------------+---------------+-----------------------+
IANA is requested to assign Types for new TLVs in the new TTZ LSA as
follows:
Type Name Allowed in
1 TTZ ID TLV TTZ LSA of LS Type 10 and 9
2 TTZ Router TLV TTZ LSA of LS Type 10
3 TTZ Options TLV TTZ LSA of LS Type 10
15. Contributors and Other Authors
1. Other Authors
Gregory Cauchie
FRANCE
Email: greg.cauchie@gmail.com
Anil Kumar S N
Huawei Technologies
Banglore
India
Email: anil.sn@huawei.com
Ning So
Tata Communications
2613 Fairbourne Cir.
Plano, TX 75082
USA
Email: ningso01@gmail.com
Lei Liu
Fujitsu
USA
Email: lliu@us.fujitsu.com
Chen, et al. Expires June 25, 2016 [Page 18]
Internet-Draft Topology-Transparent Zone December 2015
2. Contributors
Veerendranatha Reddy Vallem
Huawei Technologies
Banglore
India
Email: veerendranatharv@huawei.com
William McCall
Cisco Systems, Inc.
Bellevue, WA
USA
wimccall@cisco.com
16. Acknowledgement
The author would like to thank Acee Lindem, Abhay Roy, Dean Cheng,
Russ White, Tony Przygienda, Wenhu Lu, Lin Han and Yang Yu for their
valuable comments on this draft.
17. References
17.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, DOI 10.17487/
RFC2328, April 1998,
<http://www.rfc-editor.org/info/rfc2328>.
[RFC5250] Berger, L., Bryskin, I., Zinin, A., and R. Coltun, "The
OSPF Opaque LSA Option", RFC 5250, DOI 10.17487/RFC5250,
July 2008, <http://www.rfc-editor.org/info/rfc5250>.
[RFC5613] Zinin, A., Roy, A., Nguyen, L., Friedman, B., and D.
Yeung, "OSPF Link-Local Signaling", RFC 5613,
DOI 10.17487/RFC5613, August 2009,
<http://www.rfc-editor.org/info/rfc5613>.
Chen, et al. Expires June 25, 2016 [Page 19]
Internet-Draft Topology-Transparent Zone December 2015
17.2. Informative References
[RFC5441] Vasseur, JP., Ed., Zhang, R., Bitar, N., and JL. Le Roux,
"A Backward-Recursive PCE-Based Computation (BRPC)
Procedure to Compute Shortest Constrained Inter-Domain
Traffic Engineering Label Switched Paths", RFC 5441,
DOI 10.17487/RFC5441, April 2009,
<http://www.rfc-editor.org/info/rfc5441>.
[RFC5440] Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
Element (PCE) Communication Protocol (PCEP)", RFC 5440,
DOI 10.17487/RFC5440, March 2009,
<http://www.rfc-editor.org/info/rfc5440>.
Appendix A. Constants for LSA Distribution
MaxLSADistTime: The maximum time for an LSA to be distributed to all
the routers in an area. The value of MaxLSADistTime is set to 0.1
second.
MaxLSAGenDistTime: The maximum time for all TTZ router LSAs to be
generated by all TTZ edge routers and distributed to all the routers
in an area after a first TTZ router LSA is generated. The value of
MaxLSAGenDistTime is set to 0.3 second.
Authors' Addresses
Huaimo Chen
Huawei Technologies
Boston, MA
USA
Email: huaimo.chen@huawei.com
Renwei Li
Huawei Technologies
2330 Central expressway
Santa Clara, CA
USA
Email: renwei.li@huawei.com
Chen, et al. Expires June 25, 2016 [Page 20]
Internet-Draft Topology-Transparent Zone December 2015
Alvaro Retana
Cisco Systems, Inc.
7025 Kit Creek Rd.
Raleigh, NC 27709
USA
Email: aretana@cisco.com
Yi Yang
Cisco Systems, Inc.
7025 Kit Creek Rd.
Raleigh, NC 27709
USA
Email: yiya@cisco.com
Vic Liu
China Mobile
No.32 Xuanwumen West Street, Xicheng District
Beijing, 100053
China
Email: liuzhiheng@chinamobile.com
Mehmet Toy
Comcast
1800 Bishops Gate Blvd.
Mount Laurel, NJ 08054
USA
Email: mehmet_toy@cable.comcast.com
Chen, et al. Expires June 25, 2016 [Page 21]