PCE Working Group                                                D. King
Internet Draft                                        Old Dog Consulting
Intended status: Informational                                 J. Meuric
Expires: January 21, 2017                                      O. Dugeon
                                                          France Telecom
                                                                 Q. Zhao
                                                                D. Dhody
                                                     Huawei Technologies
                                                  Oscar Gonzalez de Dios
                                                          Telefonica I+D
                                                           July 20, 2016

     Applicability of the Path Computation Element to Inter-Area and
           Inter-AS MPLS and GMPLS Traffic Engineering

           draft-ietf-pce-inter-area-as-applicability-06


   Abstract

   The Path Computation Element (PCE) may be used for computing services
   that traverse multi-area and multi-AS Multiprotocol Label Switching
   (MPLS) and Generalized MPLS (GMPLS) Traffic Engineered (TE) networks.

   This document examines the applicability of the PCE architecture,
   protocols, and protocol extensions for computing multi-area and
   multi-AS paths in MPLS and GMPLS networks.


Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

   This Internet-Draft will expire on January 21, 2017.


King, et al.           Expires on January 21, 2017           [Page 1]


Internet-Draft         Inter-Area-AS Applicability         July 2017


Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document. Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.


Table of Contents

   1. Introduction.................................................3
      1.1. Domains.................................................4
      1.2. Path Computation........................................4
        1.2.1 PCE-based Path Computation Procedure.................5
      1.3. Traffic Engineering Aggregation and Abstraction.........5
      1.4. Traffic Engineered Label Switched Paths.................
      1.5. Inter-area and Inter-AS Capable PCE Discovery...........6
      1.6. Objective Functions.....................................6
   2. Terminology..................................................7
   3. Issues and Considerations....................................7
      3.1 Multi-homing.............................................7
      3.2 Domain Confidentiality ..................................8
      3.3 Destination Location.....................................8
   4. Domain Topologies............................................8
      4.1 Selecting Domain Paths...................................8
      4.2 Multi-Homed Domains......................................9
      4.3 Domain Topologies........................................9
      4.4 Domain Diversity.........................................9
      4.5 Synchronized Path Computations...........................9
      4.6 Domain Inclusion or Exclusion............................10
   5. Applicability of the PCE to Inter-area Traffic Engineering...11
      5.1. Inter-area Routing......................................11
      5.1.1. Area Inclusion and Exclusion..........................11
      5.1.2. Strict Explicit Path and Loose Path...................12
      5.1.3. Inter-Area Diverse Path Computation...................12
      5.2. Control and Recording of Area Crossing..................12
   6. Applicability of the PCE to Inter-AS Traffic Engineering.....12
      6.1. Inter-AS Routing........................................13
      6.1.1. Strict Explicit Path and Loose Path...................13
      6.1.2. AS Inclusion and Exclusion............................13
      6.2. Inter-AS Bandwidth Guarantees...........................13


King, et al.           Expires on January 21, 2017           [Page 2]


Internet-Draft         Inter-Area-AS Applicability         July 2017


      6.3. Inter-AS Recovery.......................................14
      6.4. Inter-AS PCE Peering Policies...........................14
   7. Multi-Domain PCE Deployment..................................14
      7.1 Traffic Engineering Database.............................15
      7.1.1 Provisioning Techniques................................16
      7.3 Pre-Planning and Management-Based Solutions..............16
      7.4 Per-Domain Computation...................................16
      7.5 Cooperative PCEs.........................................16
      7.6 Hierarchical PCEs  ......................................17
   8. Domain Confidentiality.......................................17
      8.1 Loose Hops...............................................17
      8.2 Confidential Path Segments and Path Keys.................17
   9. Point-to-Multipoint..........................................18
   10. Optical Domains.............................................18
     10.1. PCE applied to the ASON Architecture....................18
   11. Policy......................................................19
   12. TED Topology and Synchronization............................19
     12.1. Applicability of BGP-LS to PCE..........................20
   13. Manageability Considerations................................20
     13.1 Control of Function and Policy...........................20
     13.2 Information and Data Models..............................21
     13.3 Liveness Detection and Monitoring........................21
     13.4 Verifying Correct Operation..............................22
     13.5 Impact on Network Operation..............................22
   14. Security Considerations.....................................22
   15. IANA Considerations.........................................22
   16. Acknowledgements............................................22
   17. References..................................................22
     17.1. Normative References....................................22
     17.2. Informative References..................................22
   18. Author's Addresses..........................................26


1. Introduction

   Computing paths across large multi-domain environments may
   require special computational components and cooperation between
   entities in different domains capable of complex path computation.
   The Path Computation Element (PCE) [RFC4655] provides an architecture
   and a set of functional components to address this problem space.

   A PCE may be used to compute end-to-end paths across multi-domain
   environments using a per-domain path computation technique [RFC5152].
   The so called backward recursive path computation (BRPC) mechanism
   [RFC5441] defines a PCE-based path computation procedure to compute
   inter-domain constrained  Multiprotocol Label Switching (MPLS) and
   Generalized MPLS (GMPLS) Traffic Engineered (TE) networks. However,
   both per-domain and BRPC techniques assume that the sequence of
   domains to be crossed from source to destination is known, either
   fixed by the network operator or obtained by other means.

King, et al.           Expires on January 21, 2017           [Page 3]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   In more advanced deployments (including multi-area and multi-
   Autonomous System (multi-AS) environments) the sequence of domains
   may not be known in advance and the choice of domains in the end-to-
   end domain sequence might be critical to the determination of an
   optimal end-to-end path. In this case the use of the Hierarchical PCE
   [RFC6805] architecture and mechanisms may be used to discover the
   intra-area path and select the optimal end-to-end domain sequence.

   This document describes the processes and procedures available when
   using the PCE architecture, protocols and protocol extensions for
   computing inter-area and inter-AS MPLS and GMPLS Traffic TE paths.

   This document does not discuss stateful PCE, active PCE, or remotely
   initiated PCE, deployment scenarios.

1.1 Domains

   A domain can be defined as a separate administrative, geographic, or
   switching environment within the network. A domain may be further
   defined as a zone of routing or computational ability. Under these
   definitions a domain might be categorized as an Antonymous System
   (AS) or an Interior Gateway Protocol (IGP) area (as per [RFC4726]
   and [RFC4655]).

   For the purposes of this document, a domain is considered to be a
   collection of network elements within an area or AS that has a common
   sphere of address management or path computational responsibility.
   Wholly or partially overlapping domains are not within the scope of
   this document.

   In the context of GMPLS, a particularly important example of a domain
   is the Automatically Switched Optical Network (ASON) subnetwork
   [G-8080]. In this case, computation of an end-to-end path requires
   the selection of nodes and links within a parent domain where some
   nodes may, in fact, be subnetworks. Furthermore, a domain might be an
   ASON routing area [G-7715]. A PCE may perform the path computation
   function of an ASON routing controller as described in [G-7715-2].

   It is assumed that the PCE architecture is not applied to a large
   group of domains, such as Internet.


1.2 Path Computation

   For the purpose of this document it is assumed that the
   path computation is the sole responsibility of the PCE as per the
   architecture defined in [RFC4655]. When a path is required the Path
   Computation Client (PCC) will send a request to the PCE. The PCE will
   apply the required constraints and compute a path and return a


King, et al.           Expires on January 21, 2017           [Page 4]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   response to the PCC. In the context of this document it maybe
   necessary for the PCE to co-operate with other PCEs in adjacent
   domains (as per BRPC [RFC5441]) or cooperate with a Parent PCE
   (as per [RFC6805]).

   It is entirely feasible that an operator could compute a path across
   multiple domains without the use of a PCE if the relevant domain
   information is available to the network planner or network management
   platform. The definition of what relevant information is required to
   perform this network planning operation and how that information is
   discovered and applied is outside the scope of this document.

1.2.1 PCE-based Path Computation Procedure

   As highlighted, the PCE is an entity capable of computing an
   inter-domain TE path upon receiving a request from a PCC. There could
   be a single PCE per domain, or single PCE responsible for all
   domains. A PCE may or may not reside on the same node as the
   requesting PCC. A path may be computed by either a single PCE node
   or a set of distributed PCE nodes that collaborate during path
   computation.

   [RFC4655] defines that a PCC should send a path computation request
   to a particular PCE, using [RFC5440] (PCC-to-PCE communication).
   This negates the need to broadcast a request to all the PCEs. Each
   PCC can maintain information about the computation capabilities
   of the PCEs it is aware of. The PCC-PCE capability awareness can be
   configured using static configurations or by automatic and dynamic
   PCE discovery procedures.

   Once a path computation request is received, the PCC will send a
   request to the PCE. A PCE may compute the end-to-end path
   if it is aware of the topology and TE information required to
   compute the entire path. If the PCE is unable to compute the
   entire path, the PCE architecture provides co-operative PCE
   mechanisms for the resolution of path computation requests when an
   individual PCE does not have sufficient TE visibility.

   End-to-end path segments may be kept confidential through the
   application of path keys, to protect partial or full path
   information. A path key that is a token that replaces a path segment
   in an explicit route. The path key mechanism is described in
   [RFC5520]

1.3 Traffic Engineering Aggregation and Abstraction

   Networks are often constructed from multiple areas or ASes that are
   interconnected via multiple interconnect points. To maintain
   network confidentiality and scalability TE properties of each area
   and AS are not generally advertized outside each specific area or AS.

King, et al.           Expires on January 21, 2017           [Page 5]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   TE aggregation or abstraction provide mechanism to hide information
   but may cause failed path setups or the selection of suboptimal
   end-to-end paths [RFC4726]. The aggregation process may also have
   significant scaling issues for networks with many possible routes
   and multiple TE metrics. Flooding TE information breaks
   confidentiality and does not scale in the routing protocol.

   The PCE architecture and associated mechanisms provide a solution
   to avoid the use of TE aggregation and abstraction.

1.4 Traffic Engineered Label Switched Paths

   This document highlights the PCE techniques and mechanisms that exist
   for establishing TE packet and optical LSPs across multiple areas
   (inter-area TE LSP) and ASes (inter-AS TE LSP). In this context and
   within the remainder of this document, we consider all LSPs to be
   constraint-based and traffic engineered.

   Three signaling options are defined for setting up an inter-area or
   inter-AS LSP [RFC4726]:

      - Contiguous LSP
      - Stitched LSP
      - Nested LSP

   All three signaling methods are applicable to the architectures and
   procedures discussed in this document.

1.5 Inter-area and Inter-AS Capable PCE Discovery

   When using a PCE-based approach for inter-area and inter-AS path
   computation, a PCE in one area or AS may need to learn information
   related to inter-AS capable PCEs located in other ASes. The PCE
   discovery mechanism defined in [RFC5088] and [RFC5089] allow
   the discovery of PCEs and disclosure of information related to
   inter-area and inter-AS capable PCEs.

1.6 Objective Functions

   An Objective Function (OF) [RFC5541], or set of OFs, specify the
   intentions of the path computation and so define the "optimality"
   in the context of that computation request.

   An OF specifies the desired outcome of a computation. An OF does not
   describe or specify the algorithm to use, and an implementation may
   apply any algorithm or set of algorithms to achieve the result
   indicated by the OF. [RFC5541] provides the following OFs when
   computing inter-domain paths:



King, et al.           Expires on January 21, 2017           [Page 6]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   o  Minimum Cost Path (MCP);
   o  Minimum Load Path (MLP);
   o  Maximum residual Bandwidth Path (MBP);
   o  Minimize aggregate Bandwidth Consumption (MBC);
   o  Minimize the Load of the most loaded Link (MLL);
   o  Minimize the Cumulative Cost of a set of paths (MCC).

   OFs can be included in the PCE computation requests to satisfy the
   policies encoded or configured at the PCC, and a PCE may be
   subject to policy in determining whether it meets the OFs included
   in the computation request, or applies its own OFs.

   During inter-domain path computation, the selection of a domain
   sequence, the computation of each (per-domain) path fragment, and
   the determination of the end-to-end path may each be subject to
   different OFs and policy.


2. Terminology

   This document also uses the terminology defined in [RFC4655] and
   [RFC5440]. Additional terminology is defined below:

   ABR: IGP Area Border Router, a router that is attached to more than
   one IGP area.

   ASBR: Autonomous System Border Router, a router used to connect
   together ASes of a different or the same Service Provider via one or
   more inter-AS links.

   Inter-area TE LSP: A TE LSP whose path transits through two or more
   IGP areas.

   Inter-AS MPLS TE LSP: A TE LSP whose path transits through two or
   more ASes or sub-ASes (BGP confederations

   SRLG: Shared Risk Link Group.

   TED: Traffic Engineering Database, which contains the topology and
   resource information of the domain.  The TED may be fed by Interior
   Gateway Protocol (IGP) extensions or potentially by other means.


3. Issues and Considerations

3.1 Multi-homing

   Networks constructed from multi-areas or multi-AS environments
   may have multiple interconnect points (multi-homing). End-to-end path


King, et al.           Expires on January 21, 2017           [Page 7]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   computations may need to use different interconnect points to avoid
   single point failures disrupting primary and backup services.

   Domain and path diversity may also be required when computing
   end-to-end paths. Domain diversity should facilitate the selection
   of paths that share ingress and egress domains, but do not share
   transit domains. Therefore, there must be a method allowing the
   inclusion or exclusion of specific domains when computing end-to-end
   paths.

3.2 Domain Confidentiality

   Where the end-to-end path crosses multiple domains, it may be
   possible that each domain (AS or area) are administered by separate
   Service Providers, it would break confidentiality rules for a PCE
   to supply a path segment to a PCE in another domain, thus disclosing
   AS-internal topology information.

   If confidentiality is required between domains (ASes and areas)
   belonging to different Service Providers. Then cooperating PCEs
   cannot exchange path segments or else the receiving PCE or PCC will
   be able to see the individual hops through another domain.

3.3 Destination Location

   The PCC asking for an inter-domain path computation is typically
   aware of the identity of the destination node. Additionally, if the
   PCC is aware of the destination domain, it can supply this
   information as part of the path computation request. However,
   if the PCC  does not know the egress domain this information must
   be determined by another method.


4. Domain Topologies

   Constraint-based inter-domain path computation is a fundamental
   requirement for operating traffic engineered  MPLS [RFC3209] and
   GMPLS [RFC3473] networks, in inter-area and inter-AS (multi-domain)
   environments. Path computation across multi-domain networks is
   complex and requires computational co-operational entities like the
   PCE.

4.1 Selecting Domain Paths

   Where the sequence of domains is known a priori, various techniques
   can be employed to derive an optimal multi-domain path. If the
   domains are simply-connected, or if the preferred points of
   interconnection are also known, the Per-Domain Path Computation
   [RFC5152] technique can be used. Where there are multiple connections


King, et al.           Expires on January 21, 2017           [Page 8]


Internet-Draft         Inter-Area-AS Applicability         July 2017

   between domains and there is no preference for the choice of points
   of interconnection, BRPC [RFC5441] can be used to derive an optimal
   path.

   When the sequence of domains is not known in advance, the optimum
   end-to-end path can be derived through the use of a hierarchical
   relationship between domains [RFC6805].

4.2 Multi-Homed Domains

   Networks constructed from multi-areas or multi-AS environments
   may have multiple interconnect points (multi-homing). End-to-end path
   computations may need to use different interconnect points to avoid
   single point failures disrupting primary and backup services.

4.3 Domain Topologies

   Very frequently network domains are composed by dozens or hundreds of
   network elements. These network elements are usually interconnected
   between them in a partial-mesh fashion, to provide survivability
   against dual failures, and to benefit from the traffic engineering
   capabilities from MPLS and GMPLS protocols. A typical node degree
   ranges from 3 to 10 (4-5 is quite common), being the node degree the
   number of neighbors per node.

   Networks are sometimes divided into domains. Some reasons for it
   range from manageability to separation into vendor-specific domains.
   The size of the domain will be usually limited by control plane, but
   it can also be stated by arbitrary design constraints.

4.4 Domain Diversity

   Whenever an specific connectivity service is required to have 1+1
   protection feature, two completely disjoint paths must be established
   in an end to end fashion. In a multi-domain environment, this can be
   accomplished either by selecting domain diversity, or by ensuring
   diverse connection within a domain. The domain diversity ensures
   diversity in the transit domain, the diverse path should be computed
   within the ingress and egress domain. In order to compute the path
   diversity, it could be helpful to also have SRLG information in the
   domains, to ensure SRLG diversity.

4.5 Synchronized Path Computations

   In some scenarios, it would be beneficial for the operator to rely on
   the capability of the PCE to perform synchronized path computation.

   Synchronized path computations, known as Synchronization VECtors
   (SVECs) are used for dependent path computations. SVECs are
   defined in [RFC5440] and [RFC6007] provides an overview for the


King, et al.           Expires on January 21, 2017           [Page 9]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   use of the PCE SVEC list for synchronized path computations when
   computing dependent requests.

   In a H-PCE deployment a child PCE will be able to request both
   dependent and synchronized domain diverse end to end paths from its
   parent PCE.

   A non-comprehensive list of synchronized path computations include
   the following examples:

   o Route diversity: computation of two disjoint paths from a source to
     a destination (as drafted in the previous section).

   o Synchronous restoration: joint computation of a set of alternative
     paths for a set of affected LSPs as a consequence of a failure
     event. Note that in this case, the requests will potentially
     involve different source-destination pairs. In this scenario, the
     different path computation requests may arrive at different time
     stamps.

   o Batch provisioning: It is common that the operator sends a set of
     LSPs requests together, e.g in a daily of weekly basis, mainly in
     case of long lived LSPs. In order to optimize the resource usage,
     a synchronized path computation is needed.

   o Network optimization: After some time of operation, the
     distribution of the established LSP paths results in a non optimal
     use of resources. Also, inter-domain policies/agreements may have
     been changed. In such cases, a full (or partial) network planning
     action regarding the inter-domain connections will be triggered.
     This process is also known as a Global Concurrent Optimization
     (GCO) [RFC5557].

4.6 Domain Inclusion or Exclusion

   A domain sequence is an ordered sequence of domains traversed to
   reach the destination domain, a domain sequence may be supplied
   during path computation to guide the PCEs or derived via use of
   Hierarchical PCE (H-PCE).

   During multi-domain path computation, a PCC may request
   specific domains to be included or excluded in the domain sequence
   using the Include Route Object (IRO) [RFC5440] and Exclude Route
   Object (XRO) [RFC5521]. The use of Autonomous Number (AS) as an
   abstract node representing a domain is defined in [RFC3209],
   [RFC7897] specifies new sub-objects to include or exclude domains
   such as an IGP area or a 4-Byte AS number.




King, et al.           Expires on January 21, 2017          [Page 10]


Internet-Draft         Inter-Area-AS Applicability         July 2017


5. Applicability of the PCE to Inter-area Traffic Engineering

   As networks increase in size and complexity it may be required to
   introduce scaling methods to reduce the amount information flooded
   within the network and make the network more manageable. An IGP
   hierarchy is designed to improve IGP scalability by dividing the
   IGP domain into areas and limiting the flooding scope of topology
   information to within area boundaries. This restricts visibility of
   the area to routers in a single area. If a router needs to compute a
   route to destination located in another area a method is required to
   compute a path across area boundaries.

   In order to support multiple vendors in a network, in cases where
   data and/or control plane technologies cannot interoperate, it is
   useful to divide the network in vendor domains. Each vendor domain is
   an IGP area, and the flooding scope of the topology (as well as any
   other relevant information) is limited to the area boundaries.

   Per-domain path computation [RFC5152] exists to provide a method of
   inter-area path computation. The per-domain solution is based on
   loose hop routing with an Explicit Route Object (ERO) expansion on
   each Area Border Router (ABR).  This allows an LSP to be established
   using a constrained path, however at least two issues exist:

   - This method does not guarantee an optimal constrained path.

   - The method may require several crankback signaling messages
     increasing signaling traffic and delaying the LSP setup.

   The PCE-based architecture [RFC4655] is designed to solve inter-area
   path computation problems. The issue of limited topology visibility
   is resolved by introducing path computation entities that are able to
   cooperate in order to establish LSPs with source and destinations
   located in different areas.

5.1. Inter-area Routing

   An inter-area TE-LSP is an LSP that transits through at least two
   IGP areas. In a multi-area network, topology visibility remains
   local to a given area, and a node in one area will not be able to
   compute an end-to-end path across multiple areas without the use
   of a PCE.

5.1.1. Area Inclusion and Exclusion

   [RFC5441] provides a more optimal method to specify inclusion or
   exclusion of an ABR. Using this method, an operator might decide if
   an area must be include or exclude from the inter-area path
   computation.


King, et al.           Expires on January 21, 2017         [Page 11]


Internet-Draft         Inter-Area-AS Applicability         July 2017


5.1.2. Strict Explicit Path and Loose Path

   A strict explicit Path is defined as a set of strict hops, while a
   loose path is defined as a set of at least one loose hop and zero,
   one or more strict hops.  It may be useful to indicate, during the
   path computation request, if a strict explicit path is required or
   not. An inter-area path may be strictly explicit or loose (e.g., a
   list of ABRs as loose hops).

   A PCC request to a PCE does allow the indication of if a strict
   explicit path across specific areas ([RFC7897]) is required or
   desired, or if the path request is loose.

5.1.3. Inter-Area Diverse Path Computation

   It may be necessary (for protection or load-balancing) to compute
   a path that is diverse, from a previously computed path. There are
   various levels of diversity in the context of an inter-area network:

   - Per-area diversity (intra-area path segments are link, node or
     SRLG disjoint.

   - Inter-area diversity (end-to-end inter-area paths are link,
     node or SRLG disjoint).

   Note that two paths may be disjoint in the backbone area but non-
   disjoint in peripheral areas. Also two paths may be node disjoint
   within areas but may share ABRs, in which case path segments within
   an area are node disjoint but end-to-end paths are not node-disjoint.

   Per-Domain [RFC5152], BRPC [RFC5441] and H-PCE [RFC6805] mechanisms
   support the capability to compute diverse across multi-area
   topologies.

5.2. Control and Recording of Area Crossing

   In some environments it be useful for the PCE to provide a PCC the
   set of areas crossed by the end-to-end path. Then an operator may
   either want to avoid crossing specific areas, and choose to select a
   sub-optimal intra-area path. Additionally the PCE can provide the
   path information and mark each segment so the PCC has visibility of
   which piece of the path lies within which area. Although by
   implementing Path-Key, the hop-by-hop (area topology) information is
   kept confidential.


6. Applicability of the PCE to Inter-AS Traffic Engineering

   As discussed in section 4 (Applicability of the PCE to Inter-area


King, et al.           Expires on January 21, 2017         [Page 12]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   Traffic Engineering) it is necessary to divide the network into
   smaller administrative domains, or ASes. If an LSR within an AS needs
   to compute a path across an AS boundary it must also use an inter-AS
   computation technique. [RFC5152] defines mechanisms for the
   computation of inter-domain TE LSPs using network elements along the
   signaling paths to compute per-domain constrained path segments.

   The PCE was designed to be capable of computing MPLS and GMPLS paths
   across AS boundaries. This section outlines the features of a
   PCE-enabled solution for computing inter-AS paths.

6.1 Inter-AS Routing

6.1.1. Strict Explicit Path and Loose Path

   During path computation, the PCE architecture and BRPC algorithm
   allow operators to specify if the resultant LSP must follow a strict
   or a loose path. By explicitly specify the path, the operator
   request a strict explicit path which must pass through one or many
   LSR. If this behaviour is well define and appropriate for inter-area,
   it implies some topology discovery for inter-AS. So, this feature
   when the operator owns several ASes (and so, knows the topology of
   its ASes) or restricts to the well-known ASBR to avoid topology
   discovery between operators. The loose path, even if it does not
   allow granular specification of the path, protects topology
   disclosure as it not obligatory for the operator to disclose
   information about its networks.

6.1.2. AS Inclusion and Exclusion

   Like explicit and loose path, [RFC5441] allows to specify inclusion
   or exclusion of respectively an AS or an ASBR. Using this method,
   an operator might decide if an AS must be include or exclude from
   the inter-AS path computation. Exclusion and/or inclusion could also
   be specified at any step in the LSP path computation process by a PCE
   (within the BRPC algorithm) but the best practice would be to specify
   them at the edge. In opposition to the strict and loose path, AS
   inclusion or exclusion doesn't impose topology disclosure as ASes are
   public entity as well as their interconnection.

6.2 Inter-AS Bandwidth Guarantees

   Many operators with multi-AS domains will have deployed MPLS-TE
   DiffServ either across their entire network or at the domain edges
   on CE-PE links. In situations where strict QOS bounds are required,
   admission control inside the network may also be required.

   When the propagation delay can be bounded, the performance targets,
   such as maximum one-way transit delay may be guaranteed by providing


King, et al.           Expires on January 21, 2017         [Page 13]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   bandwidth guarantees along the DiffServ-enabled path, these
   requirements are described in [RFC4216].

   One typical example of the requirements in [RFC4216] is to provide
   bandwidth guarantees over an end-to-end path for VoIP traffic
   classified as EF (Expedited Forwarding) class in a DiffServ-enabled
   network. In the case where the EF path is extended across multiple
   ASes, inter-AS bandwidth guarantee would be required.

   Another case for inter-AS bandwidth guarantee is the requirement for
   guaranteeing a certain amount of transit bandwidth across one or
   multiple ASes.

6.3 Inter-AS Recovery

   During a path computation process, a PCC request may contain a
   requirement to compute a backup LSP for protecting the primary LSP,
   1+1 protection. A single, or multiple backup LSPs may also be used
   for a group of primary LSPs, m:n protection.

   Other inter-AS recovery mechanisms include [RFC4090] which adds fast
   re-route (FRR) protection to an LSP. So, the PCE could be used to
   trigger computation of backup tunnels in order to protect Inter-AS
   connectivity.

   Inter-AS recovery needs not only LSP protection but it would also be
   advisable to have multiple PCEs deployed for redundancy.

6.4 Inter-AS PCE Peering Policies

   Like BGP peering policies, inter-AS PCE peering policies is a
   requirement for operator. In inter-AS BRPC process, PCE must
   cooperate in order to compute the end-to-end LSP. So, the AS path
   must not only follow technical constraints e.g. bandwidth
   availability, but also policies define by the operator.

   Typically PCE interconnections at an AS level must follow contract
   obligations, also known as peering agreements. The PCE peering
   policies are the result of the contract negotiation and govern
   the relation between the different PCE.

7. Multi-domain PCE Deployment Options

   The PCE provides the architecture and mechanisms to compute
   inter-area and inter-AS LSPs. The objective of this document is not
   to reprint the techniques and mechanisms available, but to highlight
   their existence and reference the relevant documents that introduce
   and describe the techniques and mechanisms necessary for computing
   inter-area and inter-AS LSP based services.


King, et al.           Expires on January 21, 2017         [Page 14]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   An area or AS may contain multiple PCEs:

   - The path computation load may be balanced among a set of PCEs to
     improve scalability.

   - For the purpose of redundancy, primary and backup PCEs may be used.

   - PCEs may have distinct path computation capabilities (P2P or P2MP).

   Discovery of PCEs and capabilities per area or AS is defined in
   [RFC5088] and [RFC5089].

   Each PCE per domain can be deployed in a centralized or distributed
   architecture, the latter model having local visibility and
   collaborating in a distributed fashion to compute a path across the
   domain. Each PCE may collect topology and TE information from the
   same sources as the LSR, such as the IGP TED.

   When the PCC sends a path computation request to the PCE, the PCE
   will compute the path across a domain based on the required
   constraints. The PCE will generate the full set of strict hops from
   source to destination. This information, encoded as an ERO, is then
   sent back to the PCC that requested the path. In the event that a
   path request from a PCC contains source and destination nodes that
   are located in different domains the PCE is required to co-operate
   between multiple PCEs, each responsible for its own domain.

   Techniques for inter-domain path computation are described in
   [RFC5152] and [RFC5441], both techniques assume that the sequence of
   domains to be crossed from source to destination is well known. In
   the event that the sequence of domains is not well known, [RFC6805]
   might be used. The sequence could also be retrieve locally from
   information previously stored in the PCE database (preferably in
   the TED) by Operational Support Systems (OSS) management or other
   protocols.

7.1 Traffic Engineering Database

   TEDs are automatically populated by the IGP-TE like IS-IS-TE or
   OSPF-TE. However, no information related to AS path are provided
   by such IGP-TE. It could be helpful for BRPC algorithm as AS path
   helper, to populate a TED with suitable information regarding
   inter-AS connectivity. Such information could be obtain from
   various sources, such as BGP protocol, peering policies, OSS of the
   operator or from neighbor PCE. In any case, no topology disclosure
   must be impose in order to provide such information.

   In particular, for both inter-area and inter-AS, the TED must be
   populated. Inter-as connectivity information may be populated via
   [RFC5316] and [RFC5392].

King, et al.           Expires on January 21, 2017         [Page 15]


Internet-Draft         Inter-Area-AS Applicability         July 2017


7.1.1 Provisioning Techniques

   As PCE algorithms rely on information contained in the TED, it
   is possible to populate TED information by means of provisioning. In
   this case, the operator must regularly update and store all suitable
   information in the TED in order for the PCE to correctly compute LSP.
   Such information range from policies (e.g. avoid this LSR, or use
   this ASBR for a specific IP prefix) up to topology information (e.g.
   AS X is reachable trough a 100 Mbit/s link on this ASBR and 30 Mbit/s
   are reserved for EF traffic). Operators may choose the type and
   amount of information they can use to manage their traffic engineered
   network.

   However, some LSPs might be provisioned to link ASes or areas. In
   this case, these LSP must be announced by the IGP-TE in order to
   automatically populate the TED.

7.3 Pre-Planning and Management-Based Solutions

   Offline path computation is performed ahead of time, before the LSP
   setup is requested.  That means that it is requested by, or performed
   as part of, a management application.  This model can be seen in
   Section 5.5 of [RFC4655].

   The offline model is particularly appropriate to long-lived LSPs
   (such as those present in a transport network) or for planned
   responses to network failures.  In these scenarios, more planning is
   normally a feature of LSP provisioning.

   This model may also be used where the network operator wishes to
   retain full manual control of the placement of LSPs, using the PCE
   only as a computation tool to assist the operator, not as part of an
   automated network.

   The management based solutions could also be used in conjunction
   with the BRPC algorithm. Operator just computes the AS-Path as
   parameter for the inter-AS path computation request and let each
   PCE along the AS path compute the LSP part on its own domain.

7.4 Per-Domain Computation

   [RFC5152] defines the mechanism to compute per-domain path and must
   be used in that condition. Otherwise, BRPC [RFC5441] or HPCE RFC6805]
   will be used..

7.5 Cooperative PCEs

   When PCE cooperatation is required to compute an inter-area or inter-
   AS LSP, the techniques described in [RFC5441] and [RFC6805] could be
   used.

King, et al.           Expires on January 21, 2017         [Page 16]


Internet-Draft         Inter-Area-AS Applicability         July 2017


7.6 Hierarchical PCEs

   The H-PCE [RFC6805] proposal defines how a hierarchy of PCEs may be
   used. An operator must enable a parent PCE, and a child PCE per
   domain (AS or area). A parent PCE can be announced in the other areas
   or ASes in order for the parent PCE to contact remote child PCEs.
   Reciprocally, child PCEs are announced in remote areas or ASes in
   order to be contacted by a remote parent PCE. Parent and each child
   PCE could also be provisioned in the TED if they are not announced.


8. Domain Confidentiality

   Confidentiality typically applies to inter-provider (inter-AS) PCE
   communication. Where the TE LSP crosses multiple domains (ASes or
   areas), the path may be computed by multiple PCEs that cooperate
   together. With each local PCE responsible for computing a segment
   of the path.  However, in some cases (e.g., when ASes are
   administered by separate Service Providers), it would break
   confidentiality rules for a PCE to supply a path segment to a
   PCE in another domain, thus disclosing AS-internal or area
   topology information.

8.1 Loose Hops

   A method for preserving the confidentiality of the path segment is
   for the PCE to return a path containing a loose hop in place of the
   segment that must be kept confidential.  The concept of loose and
   strict hops for the route of a TE LSP is described in [RFC3209].

   [RFC5440] supports the use of paths with loose hops, and it is a
   local policy decision at a PCE whether it returns a full explicit
   path with strict hops or uses loose hops.  A path computation
   request may request an explicit path with strict hops, or
   may allow loose hops as detailed in [RFC5440].

8.2 Confidential Path Segments and Path Keys

   [RFC5520] defines the concept and mechanism of Path-Key. A Path-Key
   is a token that replaces the path segment information in an explicit
   route. The Path-Key allows the explicit route information to be
   encoded and in the PCEP ([RFC5440]) messages exchanged between the
   PCE and PCC.

   This Path-Key technique allows explicit route information to used
   for end-to-end path computation, without disclosing internal topology
   information between domains.




King, et al.           Expires on January 21, 2017         [Page 17]


Internet-Draft         Inter-Area-AS Applicability         July 2017


9. Point-to-Multipoint

   For the Point-to-Multipoint application scenarios for MPLS-TE LSP,
   the complexity of domain sequences, domain policies, choice and
   number of domain interconnects is magnified comparing to P2P path
   computations. Also as the size of the network grows, the number of
   leaves and branches increase and it in turn puts the scalability of
   the path computation and optimization into a bigger issue. A
   solution for the point-to-multipoint path computations may be
   achieved using the PCEP protocol extension for P2MP [RFC6006] and
   using the inter-domain P2MP procedures defined in [RFC7334].


10. Optical Domains

   The International Telecommunications Union (ITU) defines the ASON
   architecture in [G-8080]. [G-7715] defines the routing architecture
   for ASON and introduces a hierarchical architecture. In this
   architecture, the Routing Areas (RAs) have a hierarchical
   relationship between different routing levels, which means a parent
   (or higher level) RA can contain multiple child RAs. The
   interconnectivity of the lower RAs is visible to the higher level RA.

10.1. PCE applied to the ASON Architecture

   In the ASON framework, a path computation request is termed a Route
   Query. This query is executed before signaling is used to establish
   an LSP termed a Switched Connection (SC) or a Soft Permanent
   Connection (SPC). [G-7715-2] defines the requirements and
   architecture for the functions performed by Routing Controllers (RC)
   during the operation of remote route queries - an RC is synonymous
   with a PCE.

   In the ASON routing environment, a RC responsible for an RA may
   communicate with its neighbor RC to request the computation of an
   end-to-end path across several RAs. The path computation components
   and sequences are defined as follows:

   o Remote route query. An operation where a routing controller
     communicates with another routing controller, which does not have
     the same set of layer resources, in order to compute a routing
     path in a collaborative manner.

   o Route query requester. The connection controller or RC that sends a
     route query message to a routing controller requesting for one or
     more routing path that satisfies a set of routing constraints.

   o Route query responder. An RC that performs path computation upon
     reception of a route query message from a routing controller or


King, et al.           Expires on January 21, 2017         [Page 18]


Internet-Draft         Inter-Area-AS Applicability         July 2017


     connection controller, sending a response back at the end of
     computation.

   When computing an end-to-end connection, the route may be computed by
   a single RC or multiple RCs in a collaborative manner and the two
   scenarios can be considered a centralized remote route query model
   and distributed remote route query model. RCs in an ASON environment
   can also use the hierarchical PCE [RFC6805] model to fully match the
   ASON  hierarchical routing model.

11. Policy

   Policy is important in the deployment of new services and the
   operation of the network. [RFC5394] provides a framework for PCE-
   based policy-enabled path computation. This framework is based on
   the Policy Core Information Model (PCIM) as defined in [RFC3060] and
   further extended by [RFC3460].

   When using a PCE to compute inter-domain paths, policy may be
   invoked by specifying:

   - Each PCC must select which computations will be requested to a PCE;

   - Each PCC must select which PCEs it will use;

   - Each PCE must determine which PCCs are allowed to use its services
     and for what computations;

   - The PCE must determine how to collect the information in its TED,
     who to trust for that information, and how to refresh/update the
     information;

   - Each PCE must determine which objective functions and which
     algorithms to apply.

   Finally, due to the nature of inter-domain (and particularly using
   H-PCE based) path computations, deployment of policy should also
   consider the need to be sensitive to commercial and reliability
   information about domains and the interactions of services crossing
   domains.


12. TED Topology and Synchronization

   The PCE operates on a view of the network topology as presented by a
   Traffic Engineering Database.  As discussed in [RFC4655] the TED
   used by a PCE may be learnt by the relevant IGP extensions.

   Thus, the PCE may operate its TED is by participating


King, et al.           Expires on January 21, 2017         [Page 19]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   in the IGP running in the network.  In an MPLS-TE network, this
   would require OSPF-TE [RFC3630] or ISIS-TE [RFC5305].  In a GMPLS
   network it would utilize the GMPLS extensions to OSPF and IS-IS
   defined in [RFC4203] and [RFC5307].

   An alternative method to provide network topology and resource
   information is offered by [RFC7752], which is described in the
   following section.

12.1 Applicability of BGP-LS to PCE

   The concept of exchange of TE information between Autonomous Systems
   (ASes) is discussed in [RFC7752].  The information exchanged in this
   way could be the full TE information from the AS, an aggregation of
   that information, or a representation of the potential connectivity
   across the AS.  Furthermore, that information could be updated
   frequently (for example, for every new LSP that is set up across the
   AS) or only at threshold-crossing events.

   In a H-PCE deployment, the parent PCE will require the inter-domain
   topology and link status between child domains. This information may
   be learnt by a BGP-LS speaker and provided to the parent PCE,
   furthermore link-state performance including: delay, available
   bandwidth and utilized bandwidth, may also be provided to the parent
   PCE for optimal link selection.


13. Manageability Considerations

   General PCE management considerations are discussed in [RFC4655].
   In the case of multi-domains within a single service provider
   network, the management responsibility for each PCE would most
   likely be handled by the same service provider.  In the case of
   multiple ASes within different service provider networks, it will
   likely be necessary for each PCE to be configured and managed
   separately by each participating service provider, with policy
   being implemented based on an a previously agreed set of principles.

13.1 Control of Function and Policy

   As per PCEP [RFC5440] implementation allow the user to configure
   a number of PCEP session parameters. These are detailed in section
   8.1 of [RFC5440].

   In H-PCE deployments the administrative entity responsible for the
   management of the parent PCEs for multi-areas would typically be a
   single service provider. In the multiple ASes (managed by different
   service providers), it may be necessary for a third party to manage
   the parent PCE.


King, et al.           Expires on January 21, 2017         [Page 20]


Internet-Draft         Inter-Area-AS Applicability         July 2017


13.2  Information and Data Models

   A PCEP MIB module is defined in [RFC7420] that describes managed
   objects for modeling of PCEP communication including:

   o  PCEP client configuration and status,

   o  PCEP peer configuration and information,

   o  PCEP session configuration and information,

   o  Notifications to indicate PCEP session changes.

   A YANG module for PCEP has also been proposed [PCEP-YANG].

   A H-PCE MIB module, or YANG data model, will be required to
   report parent PCE and child PCE information, including:

   o  parent PCE configuration and status,

   o  child PCE configuration and information,

   o  notifications to indicate session changes between parent PCEs and
      child PCEs, and

   o  notification of parent PCE TED updates and changes.
   section 8.4 of [RFC5440] and will not be repeated here.

13.5 Impact on Network Operation

   [RFC5440] states that in order to avoid any unacceptable impact on
   network operations, a PCEP implementation should allow a limit to be
   placed on the number of sessions that can be set up on a PCEP
   speaker, it may also be practical to place a limit on the rate
   of messages sent by a PCC and received my the PCE.


14. Security Considerations

   PCEP security is defined [RFC5440]. Any multi-domain operation
   necessarily involves the exchange of information across domain
   boundaries.  This does represent a significant security and
   confidentiality risk. PCEP allows individual PCEs to maintain
   confidentiality of their domain path information using path-keys

13.3 Liveness Detection and Monitoring

   PCEP includes a keepalive mechanism to check the liveliness of a PCEP
   peer and a notification procedure allowing a PCE to advertise its


King, et al.           Expires on January 21, 2017         [Page 21]


Internet-Draft         Inter-Area-AS Applicability         July 2017


   overloaded state to a PCC. In a multi-domain environment [RFC5886]
   provides the procedures necessary to monitor the liveliness and
   performances of a given PCE chain.

13.4 Verifying Correct Operation

   In order to verify the correct operation of PCEP, [RFC5440] specifies
   the monitoring of key parameters. These parameters are detailed in
   [RFC5520].

   As PCEP operates over TCP, it may also make use of TCP security
   mechanisms, such as Transport Layer Security (TLS) and TCP
   Authentication Option (TCP-AO). Usage of these security mechanisms
   for PCEP is described in [PCEPS].

   For further considerations of the security issues related PCECP and
   to inter-domain path computation, see [RFC6952] and [RFC5376].

15. IANA Considerations

   This document makes no requests for IANA action.

16. Acknowledgements

   The author would like to thank Adrian Farrel for his review, and
   Meral Shirazipour and Francisco Javier Jimenex Chico for their
   comments.


17. References

17.1. Normative References

17.2. Informative References

     [RFC3060] Moore, B., Ellesson, E., Strassner, J., and A.
               Westerinen, "Policy Core Information Model -- Version 1
               Specification", RFC 3060, February 2001.

     [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
               and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
               Tunnels", RFC 3209, December 2001.

     [RFC3460] Moore, B., Ed., "Policy Core Information Model (PCIM)
               Extensions", RFC 3460, January 2003.

     [RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label
               Switching (GMPLS) Signaling Resource ReserVation
               Protocol-Traffic Engineering (RSVP-TE) Extensions", RFC
               3473, January 2003.

King, et al.           Expires on January 21, 2017         [Page 22]


Internet-Draft         Inter-Area-AS Applicability         July 2017


     [RFC3630] Katz, D., Kompella, K., and D. Yeung, "Traffic
               Engineering (TE) Extensions to OSPF Version 2", RFC
               3630, September 2003.

     [RFC4090] Pan, P., Swallow, G., and A. Atlas, "Fast Reroute
               Extensions to RSVP-TE for LSP Tunnels", RFC 4090, May
               2005.

     [RFC4203] Kompella, K., Ed., and Y. Rekhter, Ed., "OSPF
               Extensions in Support of Generalized Multi-
               Protocol Label Switching (GMPLS)", RFC
               4203, October 2005.

     [RFC4216] Zhang, R., Ed., and J.-P. Vasseur, Ed., "MPLS Inter-
               Autonomous System (AS) Traffic Engineering (TE)
               Requirements", RFC 4216, November 2005.

     [RFC4655] Farrel, A., Vasseur, J., and J. Ash, "A Path Computation
               Element (PCE)-Based Architecture", RFC 4655, August 2006.

     [RFC4726] Farrel, A., Vasseur, J., and A. Ayyangar, "A Framework
               for Inter-Domain Multiprotocol Label Switching Traffic
               Engineering", RFC 4726, November 2006.

     [RFC5088] Le Roux, JL., Vasseur, JP., Ikejiri, Y., and R. Zhang,
               "OSPF Protocol Extensions for Path Computation Element
               (PCE) Discovery", RFC 5088, January 2008.

     [RFC5089] Le Roux, JL., Ed., Vasseur, JP., Ed., Ikejiri, Y., and R.
               Zhang, "IS-IS Protocol Extensions for Path Computation
               Element (PCE) Discovery", RFC 5089, January 2008.

     [RFC5152] Vasseur, JP., Ayyangar, A., and R. Zhang, "A Per-Domain
               Path Computation Method for Establishing Inter-Domain
               Traffic Engineering (TE) Label Switched Paths (LSPs)",
               RFC 5152, February 2008.

     [RFC5305] Li, T. and H. Smit, "IS-IS Extensions for Traffic
               Engineering", RFC 5305, October 2008.

     [RFC5307] Kompella, K., Ed., and Y. Rekhter, Ed., "IS-IS
               Extensions in Support of Generalized Multi-Protocol
               Label Switching (GMPLS)", RFC 5307,
               October 2008.

     [RFC5316] Chen, M., Zhang, R., and X. Duan, "ISIS Extensions in
               Support of Inter-Autonomous System (AS) MPLS and GMPLS
               Traffic Engineering", December 2008.



King, et al.           Expires on January 21, 2017         [Page 23]


Internet-Draft         Inter-Area-AS Applicability         July 2017


     [RFC5376] Bitar, N., et al., "Inter-AS Requirements for the Path
               Computation Element Communication Protocol (PCECP)", RFC
               5376, November 2008.

     [RFC5392] Chen, M., Zhang, R., and X. Duan, "OSPF Extensions in
               Support of Inter-Autonomous System (AS) MPLS and GMPLS
               Traffic Engineering", RFC 5392, January 2009.

     [RFC5394] Bryskin, I., Papadimitriou, D., Berger, L., and J. Ash,
               "Policy-Enabled Path Computation Framework", RFC 5394,
               December 2008.

     [RFC5440] Ayyangar, A., Farrel, A., Oki, E., Atlas, A., Dolganow,
               A., Ikejiri, Y., Kumaki, K., Vasseur, J., and J. Roux,
               "Path Computation Element (PCE) Communication Protocol
               (PCEP)", RFC 5440, March 2009.

     [RFC5441] Vasseur, J.P., Ed., "A Backward Recursive PCE-based
               Computation (BRPC) procedure to compute shortest inter-
               domain Traffic Engineering Label Switched Paths",
               RFC5441, April 2009.

     [RFC5520] Bradford, R., Ed., Vasseur, JP., and A. Farrel,
               "Preserving Topology Confidentiality in Inter-Domain Path
               Computation Using a Path-Key-Based Mechanism", RFC 5520,
               April 2009.

     [RFC5521] Oki, E., Takeda, T., and A. Farrel, "Extensions to the
               Path Computation Element Communication Protocol (PCEP)
               for Route Exclusions", RFC 5521, April 2009.

     [RFC5541] Le Roux, J., Vasseur, J., Lee, Y., "Encoding
               of Objective Functions in the Path Computation Element
               Communication Protocol (PCEP)", RFC5541, December 2008.

     [RFC5557] Lee, Y., Le Roux, JL., King, D., and E. Oki, "Path
               Computation Element Communication Protocol (PCEP)
               Requirements and Protocol Extensions in Support of Global
               Concurrent Optimization", RFC 5557, July 2009.

     [RFC5886] Vasseur, JP., Le Roux, JL., and Y. Ikejiri, "A Set of
               Monitoring Tools for Path ComputationElement (PCE)-Based
               Architecture", RFC 5886, June 2010.

     [RFC6006] Takeda, T., Chaitou M., Le Roux, J.L., Ali Z.,
               Zhao, Q., King, D., "Extensions to the Path Computation
               Element Communication Protocol (PCEP) for
               Point-to-Multipoint Traffic Engineering Label Switched
               Paths", RFC6006, September 2010.


King, et al.           Expires on January 21, 2017         [Page 24]


Internet-Draft         Inter-Area-AS Applicability         July 2017



     [RFC6007] Nishioka, I., King, D., "Use of the Synchronization
               VECtor (SVEC) List for Synchronized Dependent Path
               Computations", RFC6007, September 2010.

     [G-8080]  ITU-T Recommendation G.8080/Y.1304, Architecture for
               the automatically switched optical network (ASON).

     [G-7715]  ITU-T Recommendation G.7715 (2002), Architecture
               and Requirements for the Automatically Switched
               Optical Network (ASON).

     [G-7715-2] ITU-T Recommendation G.7715.2 (2007), ASON routing
               architecture and requirements for remote route query.

     [RFC6805] King, D. and A. Farrel, "The Application of the Path
               Computation Element Architecture to the Determination
               of a Sequence of Domains in MPLS & GMPLS", RFC6805, July
               2010.

     [RFC6952] Jethanandani, M., Patel, K., and L. Zheng, "Analysis of
               BGP, LDP, PCEP, and MSDP Issues According to the Keying
               and Authentication for Routing Protocols (KARP) Design
               Guide", RFC 6952, May 2013.

     [RFC7334] Zhao, Q., Dhody, D., Ali Z.,  King, D.,
               Casellas, R., "PCE-based Computation
               Procedure To Compute Shortest Constrained
               P2MP Inter-domain Traffic Engineering Label Switched
               Paths", August 2014.

     [RFC7420] Stephan, E., Koushik, K., Zhao, Q., King, D., "PCE
               Communication Protocol (PCEP) Management Information
               Base", December 2014.

     [RFC7752] Gredler, H., Medved, J., Previdi, S., Farrel, A., and
               S. Ray, "North-Bound Distribution of Link-State and TE
               Information using BGP", March 2016.


     [RFC7897] Dhody, D., Palle, U., and R. Casellas, "Domain Subobjects
               for the Path Computation Element Communication Protocol
               (PCEP)", June 2016.

       [PCEPS] Lopez, D., Dios, O., Wu, W., and D. Dhody, "Secure
               Transport for PCEP", work in progress, November 2015.

   [PCEP-YANG] Dhody, D., Hardwick, J., Beeram, V., and J. Tantsura, "A
               YANG Data Model for Path Computation Element


King, et al.           Expires on January 21, 2017         [Page 25]


Internet-Draft         Inter-Area-AS Applicability         July 2017

               Communications Protocol (PCEP)", work in progress,
               January 2016.


18. Author's Addresses

   Daniel King
   Old Dog Consulting
   UK

   EMail: daniel@olddog.co.uk

   Julien Meuric
   France Telecom
   2, avenue Pierre-Marzin
   22307 Lannion Cedex

   EMail: julien.meuric@orange-ftgroup.com

   Olivier Dugeon
   France Telecom
   2, avenue Pierre-Marzin
   22307 Lannion Cedex

   EMail: olivier.dugeon@orange-ftgroup.com

   Quintin Zhao
   Huawei Technology
   125 Nagog Technology Park
   Acton, MA  01719
   US

   EMail: qzhao@huawei.com

   Dhruv Dhody
   Huawei Technologies
   Divyashree Techno Park, Whitefield
   Bangalore, Karnataka  560066
   India

   Email: dhruv.ietf@gmail.com

   Oscar Gonzalez de Dios
   Telefonica I+D
   Emilio Vargas 6, Madrid
   Spain

   EMail: ogondio@tid.es




King, et al.           Expires on January 21, 2017         [Page 26]

Internet-Draft         Inter-Area-AS Applicability         July 2017