Network Working Group Yiqun. Cai
Internet-Draft Heidi. Ou
Intended status: Standards Track Alibaba Group
Expires: December 30, 2017 Sri. Vallepalli
Mankamana. Mishra
Stig. Venaas
Cisco Systems
Andy. Green
British Telecom
June 28, 2017
PIM Designated Router Load Balancing
draft-ietf-pim-drlb-06
Abstract
On a multi-access network, one of the PIM routers is elected as a
Designated Router (DR). On the last hop LAN, the PIM DR is
responsible for tracking local multicast listeners and forwarding
traffic to these listeners if the group is operating in PIM-SM. In
this document, we propose a modification to the PIM-SM protocol that
allows more than one of these last hop routers to be selected so that
the forwarding load can be distributed among these routers.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 30, 2017.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
Cai, et al. Expires December 30, 2017 [Page 1]
Internet-Draft PIM Designated Router Load Balancing June 2017
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Functional Overview . . . . . . . . . . . . . . . . . . . . . 6
4.1. GDR Candidates . . . . . . . . . . . . . . . . . . . . . 7
4.2. Hash Mask and Hash Algorithm . . . . . . . . . . . . . . 7
4.3. Modulo Hash Algorithm . . . . . . . . . . . . . . . . . . 8
4.4. PIM Hello Options . . . . . . . . . . . . . . . . . . . . 9
5. Hello Option Formats . . . . . . . . . . . . . . . . . . . . 10
5.1. PIM DR Load Balancing Capability (DRLBC) Hello Option . . 10
5.2. PIM DR Load Balancing GDR (DRLBGDR) Hello Option . . . . 10
6. Protocol Specification . . . . . . . . . . . . . . . . . . . 11
6.1. PIM DR Operation . . . . . . . . . . . . . . . . . . . . 12
6.2. PIM GDR Candidate Operation . . . . . . . . . . . . . . . 12
6.2.1. Router receives new DRLBGDR . . . . . . . . . . . . . 13
6.2.2. Router receives updated DRLBGDR . . . . . . . . . . . 13
6.3. PIM Assert Modification . . . . . . . . . . . . . . . . . 14
7. Compatibility . . . . . . . . . . . . . . . . . . . . . . . . 15
8. Manageability Considerations . . . . . . . . . . . . . . . . 15
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16
10. Security Considerations . . . . . . . . . . . . . . . . . . . 16
11. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 16
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 16
12.1. Normative References . . . . . . . . . . . . . . . . . . 16
12.2. Informative References . . . . . . . . . . . . . . . . . 17
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 17
1. Introduction
On a multi-access LAN such as an Ethernet, one of the PIM routers is
elected as a DR. The PIM DR has two roles in the PIM-SM protocol.
On the first hop network, the PIM DR is responsible for registering
an active source with the Rendezvous Point (RP) if the group is
operating in PIM-SM. On the last hop LAN, the PIM DR is responsible
for tracking local multicast listeners and forwarding to these
listeners if the group is operating in PIM-SM.
Cai, et al. Expires December 30, 2017 [Page 2]
Internet-Draft PIM Designated Router Load Balancing June 2017
Consider the following last hop LAN in Figure 1:
( core networks )
| | |
| | |
R1 R2 R3
| | |
--(last hop LAN)--
|
|
(many receivers)
Figure 1: Last Hop LAN
Assume R1 is elected as the Designated Router. According to
[RFC4601], R1 will be responsible for forwarding traffic to that LAN
on behalf of any local members. In addition to keeping track of IGMP
and MLD membership reports, R1 is also responsible for initiating the
creation of source and/or shared trees towards the senders or the
RPs.
Forcing sole data plane forwarding responsibility on the PIM DR
proves a limitation in the protocol. In comparison, even though an
OSPF DR, or an IS-IS DIS, handles additional duties while running the
OSPF or IS-IS protocols, they are not required to be solely
responsible for forwarding packets for the network. On the other
hand, on a last hop LAN, only the PIM DR is asked to forward packets
while the other routers handle only control traffic (and perhaps drop
packets due to RPF failures). The forwarding load of a last hop LAN
is concentrated on a single router.
This leads to several issues. One of the issues is that the
aggregated bandwidth will be limited to what R1 can handle towards
this particular interface. These days, it is very common that the
last hop LAN usually consists of switches that run IGMP/MLD or PIM
snooping. This allows the forwarding of multicast packets to be
restricted only to segments leading to receivers who have indicated
their interest in multicast groups using either IGMP or MLD. The
emergence of the switched Ethernet allows the aggregated bandwidth to
exceed, some times by a large number, that of a single link. For
example, let us modify Figure 1 and introduce an Ethernet switch in
Figure 2.
Cai, et al. Expires December 30, 2017 [Page 3]
Internet-Draft PIM Designated Router Load Balancing June 2017
( core networks )
| | |
| | |
R1 R2 R3
| | |
+=gi0===gi1===gi2=+
+ +
+ switch +
+ +
+=gi4===gi5===gi6=+
| | |
H1 H2 H3
Figure 2: Last Hop Network with Ethernet Switch
Let us assume that each individual link is a Gigabit Ethernet. Each
router, R1, R2 and R3, and the switch have enough forwarding capacity
to handle hundreds of Gigabits of data.
Let us further assume that each of the hosts requests 500 Mbps of
data and different traffic is requested by each host. This
represents a total 1.5 Gbps of data, which is under what each switch
or the combined uplink bandwidth across the routers can handle, even
under failure of a single router.
On the other hand, the link between R1 and switch, via port gi0, can
only handle a throughput of 1Gbps. And if R1 is the only router, the
PIM DR elected using the procedure defined by [RFC4601], at least 500
Mbps worth of data will be lost because the only link that can be
used to draw the traffic from the routers to the switch is via gi0.
In other words, the entire network's throughput is limited by the
single connection between the PIM DR and the switch (or the last hop
LAN as in Figure 1).
The problem may also manifest itself in a different way. For
example, R1 happens to forward 500 Mbps worth of unicast data to H1,
and at the same time, H2 and H3 each requests 300 Mbps of different
multicast data. Once again packet drop happens on R1 while in the
mean time, there is sufficient forwarding capacity left on R2 and R3
and link capacity between the switch and R2/R3.
Another important issue is related to failover. If R1 is the only
forwarder on the last hop router for shared LAN, in the event of a
failure when R1 goes out of service, multicast forwarding for the
Cai, et al. Expires December 30, 2017 [Page 4]
Internet-Draft PIM Designated Router Load Balancing June 2017
entire LAN has to be rebuilt by the newly elected PIM DR. However,
if there was a way that allowed multiple routers to forward to the
LAN for different groups, failure of one of the routers would only
lead to disruption to a subset of the flows, therefore improving the
overall resilience of the network.
In this document, we propose a modification to the PIM-SM protocol
that allows more than one of these routers, called Group Designated
Router (GDR) to be selected so that the forwarding load can be
distributed among a number of routers.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119] .
With respect to PIM, this document follows the terminology that has
been defined in [RFC4601] .
This document also introduces the following new acronyms:
o GDR: GDR stands for "Group Designated Router". For each multicast
flow, either a (*,G) for ASM, or an (S,G) for SSM, a hash
algorithm (described below) is used to select one of the routers
as a GDR. The GDR is responsible for initiating the forwarding
tree building for the corresponding multicast flow.
o GDR Candidate: a last hop router that has potential to become a
GDR. A GDR Candidate must have the same DR priority and must run
the same GDR election hash algorithm as the DR router. It must
send and process new PIM Hello Options as defined in this
document. There might be more than one GDR Candidate on a LAN.
But only one can become GDR for a specific multicast flow.
3. Applicability
The proposed change described in this specification applies to PIM-SM
last hop routers only.
It does not alter the behavior of a PIM DR on the first hop network
This is because the source tree is built using the IP address of the
sender, not the IP address of the PIM DR that sends the registers
towards the RP. The load balancing between first hop routers can be
achieved naturally if an IGP provides equal cost multiple paths
(which it usually does in practice). And distributing the load to do
registering does not justify the additional complexity required to
support it.
Cai, et al. Expires December 30, 2017 [Page 5]
Internet-Draft PIM Designated Router Load Balancing June 2017
4. Functional Overview
In the existing PIM DR election, when multiple last hop routers are
connected to a multi-access LAN (for example, an Ethernet), one of
them is selected to act as PIM DR. The PIM DR is responsible for
sending local Join/Prune messages towards the RP or source. To elect
the PIM DR, each PIM router on the LAN examines the received PIM
Hello messages and compares its DR priority and IP address with those
of its neighbors. The router with the highest DR priority is the PIM
DR. If there are multiple such routers, their IP addresses are used
as the tie-breaker, as described in [RFC4601].
In order to share forwarding load among last hop routers, besides the
normal PIM DR election, the GDR is also elected on the last hop
multi-access LAN. There is only one PIM DR on the multi-access LAN,
but there might be multiple GDR Candidates.
For each multicast flow, that is (*,G) for ASM and (S,G) for SSM, a
hash algorithm is used to select one of the routers to be the GDR. A
new DR Load Balancing Capability (DRLBC) PIM Hello Option, which
contains hash algorithm type, is announced by routers on interfaces
where this specification is enabled. Last hop routers with the new
DRLBC Option advertised in its Hello, and using the same GDR election
hash algorithm and the same DR priority as the PIM DR, are considered
as GDR Candidates.
Hash Masks are defined for Source, Group and RP separately, in order
to handle PIM ASM/SSM. The masks, as well as a sorted list of GDR
Candidates' Addresses are announced by DR in a new DR Load Balancing
GDR (DRLBGDR) PIM Hello Option.
For each multicast flow, a hash algorithm is used to select one of
the routers to be the GDR. The masks are announced in PIM Hello by
DR as a DR Load Balancing GDR (DRLBGDR) Hello Option. Besides that,
a DR Load Balancing Capability (DRLBC) Hello Option, which contains
hash algorithm type, is also announced by the router on interfaces
where this specification is enabled. Last hop routers with the new
DRLBC Option advertised in its Hello, and using the same GDR election
hash algorithm and the same DR priority as the PIM DR, are considered
as GDR Candidates.
A hash algorithm based on the announced Source, Group or RP masks
allows one GDR to be assigned to a corresponding multicast state.
And that GDR is responsible for initiating the creation of the
multicast forwarding tree for multicast traffic.
Cai, et al. Expires December 30, 2017 [Page 6]
Internet-Draft PIM Designated Router Load Balancing June 2017
4.1. GDR Candidates
GDR is the new concept introduced by this specification. GDR
Candidates are routers eligible for GDR election on the LAN. To
become a GDR Candidate, a router MUST support this specification,
have the same DR priority and run the same GDR election hash
algorithm as the DR on the LAN.
For example, assume there are 4 routers on the LAN: R1, R2, R3 and
R4, which all support this specification on the LAN. R1, R2 and R3
have the same DR priority while R4's DR priority is less preferred.
In this example, R4 will not be eligible for GDR election, because R4
will not become a PIM DR unless all of R1, R2 and R3 go out of
service.
Further assume router R1 wins the PIM DR election, and R1, R2 run the
same hash algorithm for GDR election, while R3 runs a different one.
Then only R1 and R2 will be eligible for GDR election, R3 will not.
As a DR, R1 will include its own Load Balancing Hash Masks, and also
the identity of R1 and R2 (the GDR Candidates) in its DRLBGDR Hello
Option.
4.2. Hash Mask and Hash Algorithm
A Hash Mask is used to extract a number of bits from the
corresponding IP address field (32 for v4, 128 for v6), and calculate
a hash value. A hash value is used to select a GDR from GDR
Candidates advertised by PIM DR. For example, 0.0.255.0 defines a
Hash Mask for an IPv4 address that masks the first, the second and
the fourth octets.
There are three Hash Masks defined,
o RP Hash Mask
o Source Hash Mask
o Group Hash Mask
The hask masks need to be configured on the PIM routers that can
potentially become a PIM DR, unless the implementation provides
default hash mask. An implementation SHOULD provide masks with
default values 255.255.255.255 (IPv4) and
FFFF:FFFF:FFFF:FFFF:FFFFF:FFFF:FFFF:FFFF (IPv6).
Cai, et al. Expires December 30, 2017 [Page 7]
Internet-Draft PIM Designated Router Load Balancing June 2017
o If the group is ASM, and if the RP Hash Mask announced by the PIM
DR is not 0, calculate the value of hashvalue_RP [Section 4.3] to
determine GDR.
o If the group is ASM and if the RP Hash Mask announced by the PIM
DR is 0, obtain the value of hashvalue_Group [Section 4.3 ] to
determine GDR.
o If the group is SSM, use hashvalue_SG [Section 4.3] to determine
GDR.
A simple Modulo hash algorithm will be discussed in this document.
However, to allow other hash algorithm to be used, a 4-bytes "Hash
Algorithm Type" field is included in DRLBC Hello Option to specify
the hash algorithm used by a last hop router.
If different hash algorithm types are advertised among last hop
routers, only last hop routers running the same hash algorithm as the
DR (and having the same DR priority as the DR) are eligible for GDR
election.
4.3. Modulo Hash Algorithm
Modulo hash algorithm is discussed here as an example, with detailed
description on hashvalue_RP.
o For ASM groups, with a non-zero RP_hash mask, hash value is
calculated as:
hashvalue_RP = (((RP_address & RP_hashmask) >> N) & 0xFFFF) % M
RP_address is the address of the RP defined for the group. N
is the number of zeros, counted from the least significant bit
of the RP_hashmask. M is the number of GDR Candidates.
For example, Router X with IPv4 address 203.0.113.1, receives a
DRLBGDR Hello Option from the DR, which announces RP Hash Mask
0.0.255.0, and a list of GDR Candidates, sorted by IP addresses
from high to low, 203.0.113.3, 203.0.113.2 and 203.0.113.1.
The ordinal number assigned to those addresses would be:
0 for 203.0.113.3; 1 for 203.0.113.2; 2 for 203.0.113.1 (Router
X)
Assume there are 2 RPs: RP1 192.0.2.1 for Group1 and RP2
198.51.100.2 for Group2. Following the modulo hash algorithm:
Cai, et al. Expires December 30, 2017 [Page 8]
Internet-Draft PIM Designated Router Load Balancing June 2017
N is 8 for 0.0.255.0, and M is 3 for the total number of GDR
Candidates. The hashvalue_RP for RP1 192.0.2.1 is:
(((192.0.2.1 & 0.0.255.0) >> 8) & 0xFFFF % 3) = 2 % 3 = 2
matches the ordinal number assigned to Router X. Router X will
be the GDR for Group1, which uses 192.0.2.1 as the RP.
The hashvalue_RP for RP2 198.51.100.2 is:
(((198.51.100.2 & 0.0.255.0) >> 8) & 0xFFFF % 3) = 100 % 3 = 1
which is different from Router X's ordinal number 2, hence,
Router X will not be GDR for Group2.
o If RP_hashmask is 0, a hash value for ASM group is calculated
using the group Hash Mask:
hashvalue_Group = (((Group_address & Group_hashmask) >> N) &
0xFFFF) % M
Compare hashvalue_Group with Ordinal number assigned to Router
X, to decide if Router X is the GDR.
o For SSM groups, a hash value is calculated using both the source
and group Hash Mask
hashvalue_SG = ((((Source_address & Source_hashmask) >> N_S) &
0xFFFF) ^ (((Group_address & Group_hashmask) >> N_G) & 0xFFFF))
% M
4.4. PIM Hello Options
When a last hop PIM router sends a PIM Hello from an interface with
this specification enabled, it includes a new option, called "Load
Balancing Capability (DRLBC)".
Besides this DRLBC Hello Option, the elected PIM DR also includes a
new "DR Load Balancing GDR (DRLBGDR) Hello Option". The DRLBGDR
Hello Option consists of three Hash Masks as defined above and also
the sorted list of all GDR Candidates' Address on the last hop LAN.
The elected PIM DR uses DRLBC Hello Option advertised by all routers
on the last hop LAN to compose its DRLBGDR . The GDR Candidates use
DRLBGDR Hello Option advertised by PIM DR to calculate hash value.
Cai, et al. Expires December 30, 2017 [Page 9]
Internet-Draft PIM Designated Router Load Balancing June 2017
5. Hello Option Formats
5.1. PIM DR Load Balancing Capability (DRLBC) Hello Option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = TBD | Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Hash Algorithm Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Capability Hello Option
Type: TBD.
Length: 4 octets
Hash Algorithm Type: 0 for Modulo hash algorithm
This DRLBC Hello Option SHOULD be advertised by last hop routers from
interfaces with this specification enabled.
5.2. PIM DR Load Balancing GDR (DRLBGDR) Hello Option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = TBD | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Group Mask |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Mask |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RP Mask |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| GDR Candidate Address(es) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: GDR Hello Option
Type: TBD
Length: 3 x (4 byte or 16 byte) + n x (4 byte or 16 byte) where n
is number of GDR candidate
Cai, et al. Expires December 30, 2017 [Page 10]
Internet-Draft PIM Designated Router Load Balancing June 2017
Group Mask (32/128 bits): Mask
Source Mask (32/128 bits): Mask
RP Mask (32/128 bits): Mask
All masks MUST be in the same address family as the Hello IP
header.
GDR Address (32/128 bits): Address(es) of GDR Candidate(s)
All addresses must be in the same address family as the Hello
IP header. The addresses are sorted from high to low. The
order is converted to the ordinal number associated with each
GDR candidate in hash value calculation. For example,
addresses advertised are R3, R2, R1, the ordinal number
assigned to R3 is 0, to R2 is 1 and to R1 is 2.
If "Interface ID" option, as described in [RFC6395], presents
in a GDR Candicate's PIM Hello message, and the "Router ID"
portion is non-zero,
+ For IPv4, the "GDR Candidate Address" will be set directly
to "Router ID".
+ For IPv6, the "GDR Candidate Address" will be set to the
IPv4-IPv6 translated address of "Router ID", as described in
[RFC4291] , that is the "Router-ID" is appended to the
prefix of 96-bits zeros.
If the "Interface ID" option is not present in a GDR
Candidate's PIM Hello message, or if the "Interface ID" option
is present, but"Router ID" field is zero, the "GDR Candidate
Address" will be the IPv4 or IPv6 source address from PIM Hello
message.
This DRLBGDR Hello Option SHOULD only be advertised by the
elected PIM DR.
6. Protocol Specification
Cai, et al. Expires December 30, 2017 [Page 11]
Internet-Draft PIM Designated Router Load Balancing June 2017
6.1. PIM DR Operation
The DR election process is still the same as defined in [RFC4601]. A
DR that has this specification enabled on the interface, advertises
the new LBGRD Hello Option, which contains value of masks from user
configuration, followed by a sorted list of all GDR Candidates'
Addresses, from high to low. Moreover, same as non-DR routers, DR
also advertises DRLBC Hello Option to indicate its capability of
supporting this specification and the type of its GDR election hash
algorithm.
If a PIM DR receives a PIM Hello with DRLBGRD Option, the PIM DR
SHOULD ignore the TLV.
If a PIM DR receives a neighbor DRLBC Hello Option, which contains
the same hash algorithm type as the DR, and the neighbor has the same
DR priority as the DR, PIM DR SHOULD consider the neighbor as a GDR
Candidate and insert the GDR Candidate's Address into the sorted list
of DRLBGRD Option.
6.2. PIM GDR Candidate Operation
When an IGMP/MLD join is received, without this proposal, only PIM DR
will handle the join and potentially run into the issues described
earlier. Using this proposal, a hash algorithm is used on GDR
Candidate to determine which router is going to be responsible for
building forwarding trees on behalf of the host.
A router which supports this specification, a interface where this
protocol is enabled advertises DRLBC Hello Option in its PIM Hello,
even if the router may not be considered as a GDR Candidate, for
example, due to low DR priority. once DR election is done, DRLBGDR
Hello option would be received from the current PIM DR on link.
A GDR Candidate may receive a DRLBGDR Hello Option from PIM DR, with
different Hash Masks from those configured on it, The GDR Candidate
must use the Hash Masks advertised by the PIM DR to calculate the
hash value.
A GDR Candidate may receive a DRLBGDR Hello Option from a PIM router
which is not DR. The GDR Candidate MUST ignore such DRLBGDR Hello
Option.
A GDR Candidate may receive a Hello from the elected PIM DR, and the
PIM DR does not support this specification. The GDR election
described by this specification will not take place, that is only the
PIM DR joins the multicast tree.
Cai, et al. Expires December 30, 2017 [Page 12]
Internet-Draft PIM Designated Router Load Balancing June 2017
A router only act as GDR if it is included in the GDR list of DRLBGDR
Hello Option
6.2.1. Router receives new DRLBGDR
When a router receives new DRLBGDR from the current PIM DR, it need
to process and check if router is in list of of GDR
1. If router is not listed as a GDR candidate in DRLBGDR , no action
needed.
2. If router is listed as a GDR candidate in DRLBGDR, then it need
to process each of the groups in the IGMP/MLD reports. The masks
are announced in the PIM Hello by DR as DRLBGDR Hello option.
For each of groups in the reports it need to run hash algorithem
(described in section 4.3) based on the announced Source, Group
or RP masks to determine if it is GDR for specified group. If
hash result is to be GDR for multicast flow, it does build
multicast forwarding tree. if it is not GDR for flow, no action
is needed.
6.2.2. Router receives updated DRLBGDR
If router (GDR or non GDR) receives an unchanged DRLBGDR from the
current PIM DR, no action needed.
If router (GDR or non GDR) receives a new or modified DRLBGDR from
the current PIM DR. It requires processing as described below
1. If it was GDR and still included in current GDR list: It need to
process each of the groups, run hash algorithem to check if it is
still GDR for given group.
If it was GDR for group earlier. and even new hash choose it
as GDR, no processing required.
If it was GDR for group earlier and now it is no more GDR,
then it sets its assert metric for this flow to be
(PIM_ASSERT_INFINITY - 1), as explained in Sec 6.3
If it was not GDR for group earlier, and even new hash does
not make it GDR no processing required.
If it was not GDR earlier and now becomes GDR, it starts
building multicast forwarding tree for this flow.
2. If it was non GDR , and updated DRLBGDR from current PIM DR
contains this router as one of the GDR. In this case this router
Cai, et al. Expires December 30, 2017 [Page 13]
Internet-Draft PIM Designated Router Load Balancing June 2017
being new GDR candiate MUST run hash algorithem for each of the
groups (multicast flows) and for given group,
If it is not GDR, no processing is required.
If it is hased as GDR , it need to build multicast forwarding
tree.
3. If a router receives IGMP/MLD report for flow for which the
router has been the GDR AND the DRLBGDR has changed since last
report for this flow, then the router MUST determine if it is
still the GDR. if it is, no action needed. if it is not, then the
router sets its assert metric for this flow to be
(PIM_ASSERT_INFINITY - 1) as explained in Sec 6.3.
6.3. PIM Assert Modification
It is possible that the identity of the GDR might change in the
middle of an active flow. Examples this could happen include:
When a new PIM router comes up
When a GDR restarts
When the GDR changes, existing traffic might be disrupted.
Duplicates or packet loss might be observed. To illustrate the case,
consider the following scenario: there are two streams G1 and G2. R1
is the GDR for G1, and R2 is the GDR for G2. When R3 comes up
online, it is possible that R3 becomes GDR for both G1 and G2, hence
R3 starts to build the forwarding tree for G1 and G2. If R1 and R2
stop forwarding before R3 completes the process, packet loss might
occur. On the other hand, if R1 and R2 continue forwarding while R3
is building the forwarding trees, duplicates might occur.
This is not a typical deployment scenario but it still might happen.
Here we describe a mechanism to minimize the impact. The motivation
is that we want to minimize packet loss. And therefore, we would
allow a small amount of duplicates and depend on PIM Assert to
minimize the duplication.
When the role of GDR changes as above, instead of immediately
stopping forwarding, R1 and R2 continue forwarding to G1 and G2
respectively, while at the same time, R3 build forwarding trees for
G1 and G2. This will lead to PIM Asserts.
With introduction of GDR, the following modification to the Assert
packet MUST be done: if a router enables this specification on its
downstream interface, but it is not a GDR (before network event it
Cai, et al. Expires December 30, 2017 [Page 14]
Internet-Draft PIM Designated Router Load Balancing June 2017
was GDR), it would adjust its Assert metric to (PIM_ASSERT_INFINITY -
1).
Using the above example, for G1, assume R1 and R3 agree on the new
GDR, which is R3. R1 will set its Assert metric as
(PIM_ASSERT_INFINITY - 1). That will make R3, which has normal
metric in its Assert as the Assert winner.
For G2, assume it takes a little bit longer time for R2 to find out
that R3 is the new GDR and still thinks itself being the GDR while R3
already has assumed the role of GDR. Since both R2 and R3 think they
are GDRs, they further compare the metric and IP address. If R3 has
the better routing metric, or same metric but better tie-breaker, the
result will be consistent with GDR selection. If unfortunately, R2
has the better metric or same metric but better tie-breaker R2 will
become the Assert winner and continues to forward traffic. This will
continue until:
The next PIM Hello option from DR is seen that selects R3 as the GDR.
R3 will then build the forwarding tree and send an Assert.
The process continues until R2 agrees to the selection of R3 as being
the GDR, and set its own Assert metric to (PIM_ASSERT_INFINITY - 1),
which will make R3 the Assert winner. During the process, we will
see intermittent duplication of traffic but packet loss will be
minimized. In the unlikely case that R2 never relinquishes its role
as GDR (while every other router thinks otherwise), the proposed
mechanism also helps to keep the duplication to a minimum until
manual intervention takes place to remedy the situation.
7. Compatibility
In case of hybrid Ethernet shared LAN ( where some PIM router enables
specification defined in this draft and some do not enable)
o If router which does not support specification defined in this
draft becomes DR on link, it MUST be only DR on link as [RFC4601]
and there would be no router which would act as GDR.
o If router which does not support specification defined in this
draft becomes non DR on link, then it should act as non-DR defined
in [RFC4601].
8. Manageability Considerations
o All of the router in LAN who are supporting this specification
MUST use identical Hash Algorithm Type (described in section 5.1).
In case of hybrid Hash Algorithm Type router must go backward to
Cai, et al. Expires December 30, 2017 [Page 15]
Internet-Draft PIM Designated Router Load Balancing June 2017
use DR election method defined in PIM-SM [RFC4601]. Migration
between different algorithem type is out of scope of this
document.
9. IANA Considerations
Two new PIM Hello Option Types have been assigned to the DR Load
Balancing messages. [HELLO-OPT], this document recommends 34(0x22)
as the new "PIM DR Load Balancing Capability Hello Option", and
35(0x23) as the new "PIM DR Load Balancing GDR Hello Option".
10. Security Considerations
Security of the new DR Load Balancing PIM Hello Options is only
guaranteed by the security of PIM Hello message, so the security
considerations for PIM Hello messages as described in PIM-SM
[RFC4601] apply here.
11. Acknowledgement
The authors would like to thank Steve Simlo, Taki Millonis for
helping with the original idea, Bill Atwood, Bharat Joshi for review
comments, Toerless Eckert and Rishabh Parekh for helpful conversation
on the document.
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, DOI 10.17487/RFC4291, February
2006, <http://www.rfc-editor.org/info/rfc4291>.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)", RFC 4601,
DOI 10.17487/RFC4601, August 2006,
<http://www.rfc-editor.org/info/rfc4601>.
[RFC6395] Gulrajani, S. and S. Venaas, "An Interface Identifier (ID)
Hello Option for PIM", RFC 6395, DOI 10.17487/RFC6395,
October 2011, <http://www.rfc-editor.org/info/rfc6395>.
Cai, et al. Expires December 30, 2017 [Page 16]
Internet-Draft PIM Designated Router Load Balancing June 2017
12.2. Informative References
[HELLO-OPT]
IANA, "PIM Hello Options", IANA PIM-HELLO-OPTIONS, March
2007.
Authors' Addresses
Yiqun Cai
Alibaba Group
Email: yiqun.cai@alibaba-inc.com
Heidi Ou
Alibaba Group
Sri Vallepalli
Cisco Systems
3625 Cisco Way,
Sanjose, CALIFORNIA 95134
UNITED STATES
Email: svallepa@cisco.com
Mankamana Prasad Mishra
Cisco Systems
821 Alder Drive,
MILPITAS, CALIFORNIA 95035
UNITED STATES
Email: mankamis@cisco.com
Stig Venaas
Cisco Systems
821 Alder Drive,
MILPITAS, CALIFORNIA 95035
UNITED STATES
Email: stig@cisco.com
Cai, et al. Expires December 30, 2017 [Page 17]
Internet-Draft PIM Designated Router Load Balancing June 2017
Andy Green
British Telecom
Adastral Park
Ipswich IP5 2RE
United Kingdom
Email: andy.da.green@bt.com
Cai, et al. Expires December 30, 2017 [Page 18]