PINT Working Group Murali Krishnaswamy
Internet Draft Lucent Technologies
Dan Romascanu
Avaya Communication
Expires January 2001 24 July 2000
Management Information Base for the PINT Services Architecture
<draft-ietf-pint-mib-03.txt>
Abstract
This memo describes a proposed MIB for the PINT Services
Architecture.
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet- Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
1. Introduction
PINT services are an emerging set of new Internet based applications
where voice (and fax) requests to the PSTN (Public Switched Telephone
Krishnaswamy, Romascanu [Page 1]
Internet Draft PINT MIB July 2000
Network) are carried over the Internet. RFC 2458 [1] gives a good
introduction to the (pre-standard) PINT architecture and services.
It also has examples of some of the early implementations of pre-
PINT.
This document defines a MIB which contains the elements for
monitoring the performance of a PINT based service. The MIB consists
of details of the four basic PINT services and their performance
statistics measured under various criteria.
It is not the purpose of this MIB to enable management of the PINT
networking elements. We are concerned only with the PINT specific
performance parameters. While it is understood that PINT service
performance is closely related to host and network performance, they
are not addressed here.
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [2].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
RFC 1155 [3], RFC 1212 [4] and RFC 1215 [5]. The second version,
called SMIv2, is described in RFC 2578 [6], RFC 2579 [7] and RFC
2580 [8].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in RFC 1157 [9]. A second version of the SNMP message
protocol, which is not an Internet standards track protocol, is
called SNMPv2c and described in RFC 1901 [10] and RFC 1906 [11].
The third version of the message protocol is called SNMPv3 and
described in RFC 1906 [11], RFC 2572 [12] and RFC 2574 [13].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in RFC 1157 [9]. A second set of protocol operations
and associated PDU formats is described in RFC 1905 [14].
o A set of fundamental applications described in RFC 2573 [15] and
the view-based access control mechanism described in RFC 2575
Krishnaswamy, Romascanu [Page 2]
Internet Draft PINT MIB July 2000
[16].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [17].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine-readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
3. The need for PINT services monitoring MIB
Traditionally voice (and fax) requests originate and terminate inside
a PSTN network. This network is well known for robust handling of the
requests, in terms of availability and security. However when the
requests originate from the Internet there is a concern both on the
part of the user as well as the provider about issues like reliable
forwarding of the call requests to the PINT gateway under various
network conditions, user/host authentication, secure handling of the
user information etc. Performance and security management becomes
all the more important where PINT services cross multiple administra-
tive domains (or providers).
This MIB is an attempt to list the parameters that need to be moni-
tored on an user, PINT client, PINT server and PINT gateway basis.
(PINT services, their invocation methods/protocols and security
issues associated with the PINT architecture are discussed in detail
in [18]).
4. PINT MIB - Overview
Following is a list of some explanations on the MIB definitions that
Krishnaswamy, Romascanu [Page 3]
Internet Draft PINT MIB July 2000
we have chosen to construct.
o The basic purpose of this MIB is to monitor the access to PINT
services both from the performance and security point of view.
Information may pertain to a certain user or his/her system
(PINT client) or the system providing the PINT services (PINT
server) or the PINT gateway that forwards the call to the PSTN
network.
o We propose to build the configuration table as an extension of
the Application MIB - RFC 2287 [19] using the augments con-
struct. Server location and contact might be retrieved from the
standard MIB-II sysLocation and sysContact objects. There is no
need to replicate this information in the PINT MIB. However, the
PINT administrator may be a different person than the sysadmin
with global responsibilities, thus a pintSysContact object is
defined.
o We chose to monitor the gateway connections from the PINT
server. While the agent runs in the PINT servers, the connec-
tions to the gateways might need to be monitored in order to
understand what goes on. We placed them in a separate MIB group,
and by using MODULE-COMPLIANCE clauses, agents that cannot
implement this stuff will not be mandated to do it.
o There is no traps definition in this preliminary proposal. Note
that thresholding on counters is always possible by using a
standard mechanism defined by the Remote Monitoring MIB, that
can be referenced here. Some events that may be defined by using
this mechanisms:
* continuous login/authentication failure or refusal from a
particular client or user
* nuisance call - repeated calls (within a specified period)
to a number originating from the same user
o The client performance and user performance tables may be rather
resource demanding for an agent implementation. In some MIBs,
like the Remote Monitoring (RMON) MIBs, control mechanisms were
built in order to activate those statistics on demand. If
needed, a sorting ('topN') mechanism can be designed, so that a
sorted view of clients or users is presented for the high level
Krishnaswamy, Romascanu [Page 4]
Internet Draft PINT MIB July 2000
debugging.
o We built a time-distribution trying to cover both short-lived,
as well as longer sessions (1-10 secs, 10 secs - 1 min., 1-15
min., 15 mins-24 hours, longer).
o PintServerClientAddress is defined as a SnmpAdminString. It may
include an IpAddress and/or name, but we preferred to minimize
the number of indices at this stage, and keep a human-readable
format at the same time.
o We define pintServerUserIdName as the UserId. This UserId needs
to be unique across multiple PINT servers and gateways (depend-
ing on the architecture) and is mapped to the SessionId. One
way to achieve this uniqueness is by appending clientId to the
UserId string before sending to the PINT server. The SessionId
could then be a combination of this new UserId and a timestamp.
5. Definitions
PINT-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, Counter32, MODULE-IDENTITY, mib-2
FROM SNMPv2-SMI
TEXTUAL-CONVENTION
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
SysApplInstallPkgIndex
FROM SYSAPPL-MIB
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB; -- RFC 2271 [20]
pintMib MODULE-IDENTITY
LAST-UPDATED "200007241525Z"
ORGANIZATION "IETF PINT Working Group"
CONTACT-INFO
"
Chairs:
Krishnaswamy, Romascanu [Page 5]
Internet Draft PINT MIB July 2000
Steve Bellovin
E-mail: smb@research.att.com
Igor Faynberg
E-mail: faynberg@lucent.com
Murali Krishnaswamy
Postal: 3C-512, 101 Crawfords Corner Rd.
Holmdel, NJ 07733
Tel: +1 (732)949-3611
FAX: +1 (732)949-3210
E-mail: murali@lucent.com
Dan Romascanu
Postal: Atidim Technology Park, Bldg 3
Tel Aviv, Israel
Tel: +972 3 6458414
E-mail: dromasca@avaya.com
General Discussion:pint@lists.bell-labs.com
To Subscribe: pint-request@lists.bell-labs.com
In Body: subscribe your-email-addres
Archive: http://www.bell-labs.com/mailing-lists/pint/
"
DESCRIPTION
"This MIB defines the objects necessary to monitor
PINT Services"
REVISION "200007241525Z"
DESCRIPTION
"Initial version, published as RFC xxxx."
::= { mib-2 99999 } -- Not an IANA number
PintServiceType ::= TEXTUAL-CONVENTION
STATUS current
SYNTAX INTEGER {
r2C(1), -- Request-to-Talk
r2F(2), -- Request-to-Fax
r2FB(3), -- Request-to-Fax-Back
r2HC(4) -- Request-to-Hear-Content
}
DESCRIPTION
Krishnaswamy, Romascanu [Page 6]
Internet Draft PINT MIB July 2000
"This TC describes the type of a PINT service."
PintPerfStatPeriod ::= TEXTUAL-CONVENTION
STATUS current
SYNTAX INTEGER {
last30sec(1), -- Performance Statics for the last 30 sec
last15min(2), -- 15 min
last24Hr(3), -- 24 Hour
sinceReboot(4) -- Since the time the pint server was
-- last rebooted
}
DESCRIPTION
"This TC describes the statistics period of time.
Note that the values of the counters indexed with a value
SinceReboot(4) can be potentially affected by a counter rollover.
It is the responsibility of the application using this object to
take into account that the counter has been zeroed each time it
reached a value of (2**32-1)."
pintServerConfig OBJECT IDENTIFIER ::= { pintMib 1 }
pintServerMonitor OBJECT IDENTIFIER ::= { pintMib 2 }
pintMibConformance OBJECT IDENTIFIER ::= { pintMib 3 }
-- pintServerConfig - PINT configuration MIB variables
pintReleaseNumber OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of version of the PINT protocol supported
by this agent."
::= { pintServerConfig 1 }
pintSysContact OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Contact information related to the administration of the PINT
services."
::= { pintServerConfig 2 }
pintApplInstallPkgTable OBJECT-TYPE
Krishnaswamy, Romascanu [Page 7]
Internet Draft PINT MIB July 2000
SYNTAX SEQUENCE OF PintApplInstallPkgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table describing the PINT applications that are installed."
::= { pintServerConfig 3 }
pintApplInstallPkgEntry OBJECT-TYPE
SYNTAX PintApplInstallPkgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries per PINT Application."
AUGMENTS { sysApplInstallPkgIndex }
::= { pintApplInstallPkgTable 1 }
PintApplInstallPkgEntry ::= SEQUENCE {
pintApplInstallPkgDescription SnmpAdminString
}
pintApplInstallPkgDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Textual description of the installed PINT application."
::= { pintApplInstallPkgEntry 1 }
pintRegisteredGatewayTable OBJECT-TYPE
SYNTAX SEQUENCE OF PintRegisteredGatewayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table describing the registered gateway applications."
::= { pintServerConfig 4 }
pintRegisteredGatewayEntry OBJECT-TYPE
SYNTAX PintRegisteredGatewayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries per Registered Gateway Application."
AUGMENTS { sysApplInstallPkgIndex, pintRegisteredGatewayName }
::= { pintRegisteredGatewayTable 1 }
pintRegisteredGatewayEntry ::= SEQUENCE {
pintRegisteredGatewayName SnmpAdminString
Krishnaswamy, Romascanu [Page 8]
Internet Draft PINT MIB July 2000
pintRegisteredGatewayDescription SnmpAdminString
}
pintRegisteredGatewayName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Name of the registered gateway."
::= { pintRegisteredGatewayEntry 1 }
pintRegisteredGatewayDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Textual description of the registered gateway."
::= { pintRegisteredGatewayEntry 2 }
-- pintServerMonitor - PINT monitoring statistics MIB variables
pintServerGlobalPerf OBJECT IDENTIFIER ::= {pintServerMonitor 1 }
pintServerClientPerf OBJECT IDENTIFIER ::= {pintServerMonitor 2 }
pintServerUserIdPerf OBJECT IDENTIFIER ::= {pintServerMonitor 3 }
pintServerGatewayPerf OBJECT IDENTIFIER ::= {pintServerMonitor 4 }
pintServerGlobalStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF PintServerGlobalStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table displaying the monitored global server statistics."
::= { pintServerGlobalPerf 1 }
pintServerGlobalStatsEntry OBJECT-TYPE
SYNTAX PintServerGlobalStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries in the global statistics table.
One entry is defined for each monitored service type and
performance statistics collection period."
INDEX {pintServerServiceTypeIndex, pintServerPerfStatPeriodIndex}
::= { pintServerGlobalStatsTable 1 }
PintServerGlobalStatsEntry ::= SEQUENCE {
Krishnaswamy, Romascanu [Page 9]
Internet Draft PINT MIB July 2000
pintServerServiceTypeIndex PintServiceType,
pintServerPerfStatPeriodIndex PintPerfStatPeriod,
pintServerGlobalCallsReceived Counter32,
pintServerGlobalSuccessfulCalls Counter32,
pintServerGlobalDisconnectedCalls Counter32,
pintServerGlobalDisconnectedClientUserAuthorizationFailureCalls
Counter32,
pintServerGlobalDisconnectedServerProblemCalls Counter32,
pintServerGlobalDisconnectedGatewayProblemCalls Counter32
}
pintServerServiceTypeIndex OBJECT-TYPE
SYNTAX PintServiceType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The unique identifier of the monitored service."
::= { pintServerGlobalStatsEntry 1 }
pintServerPerfStatPeriodIndex OBJECT-TYPE
SYNTAX PintPerfStatPeriod
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Time period for which the performance statistics are requested
from the pint server."
::= { pintServerGlobalStatsEntry 2 }
pintServerGlobalCallsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received global calls."
::= { pintServerGlobalStatsEntry 3 }
pintServerGlobalSuccessfulCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of global successful calls."
::= { pintServerGlobalStatsEntry 4 }
pintServerGlobalDisconnectedCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Krishnaswamy, Romascanu [Page 10]
Internet Draft PINT MIB July 2000
STATUS current
DESCRIPTION
"Number of global disconnected (failed) calls."
::= { pintServerGlobalStatsEntry 5 }
pintServerGlobalDisconnectedClientUserAuthorizationFailureCalls
OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of global calls that were disconnected because of client
or user authorization failure."
::= { pintServerGlobalStatsEntry 6 }
pintServerGlobalDisconnectedServerProblemCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of global calls that were disconnected because of
server problems."
::= { pintServerGlobalStatsEntry 7 }
pintServerGlobalDisconnectedGatewayProblemCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of global calls that were disconnected because of
gateway problems."
::= { pintServerGlobalStatsEntry 8 }
pintServerClientStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF PintServerClientStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table displaying the monitored server client statistics."
::= { pintServerClientPerf 1 }
pintServerClientStatsEntry OBJECT-TYPE
SYNTAX PintServerClientStatsEntry
Krishnaswamy, Romascanu [Page 11]
Internet Draft PINT MIB July 2000
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries in the client server statistics table.
One entry is defined for each client identified by name,
monitored service type and performance statistics collection
period."
INDEX {pintServerClientAddress, pintServerServiceTypeIndex,
pintServerPerfStatPeriodIndex}
::= { pintServerClientStatsTable 1 }
PintServerClientStatsEntry ::= SEQUENCE {
pintServerClientAddress SnmpAdminString,
pintServerClientCallsReceived Counter32,
pintServerClientSuccessfulCalls Counter32,
pintServerClientDisconnectedCalls Counter32,
pintServerClientDisconnectedClientAuthorizationFailureCalls
Counter32,
pintServerClientDisconnectedEgressFacilityProblemCalls Counter32
}
pintServerClientAddress OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The unique identifier of the monitored client
identified by its address represented as as a string."
::= { pintServerClientStatsEntry 1 }
pintServerClientCallsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls received from the specific client."
::= { pintServerClientStatsEntry 2 }
pintServerClientSuccessfulCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls from the client successfully completed."
::= { pintServerClientStatsEntry 3 }
Krishnaswamy, Romascanu [Page 12]
Internet Draft PINT MIB July 2000
pintServerClientDisconnectedCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls received from the client, and that were
disconnected (failed)."
::= { pintServerClientStatsEntry 4 }
pintServerClientDisconnectedClientAuthorizationFailureCalls
OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls from the client that were disconnected because of
client authorization failure."
::= { pintServerClientStatsEntry 5 }
pintServerClientDisconnectedEgressFacilityProblemCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls from the client that were disconnected because
of egress facility problems."
::= { pintServerClientStatsEntry 6 }
pintServerUserIdStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF PintServerUserIdStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table displaying the monitored Pint service user statistics."
::= { pintServerUserIdPerf 1 }
pintServerUserIdStatsEntry OBJECT-TYPE
SYNTAX PintServerUserIdStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries in the user statistics table.
One entry is defined for each user identified by name,
each monitored service type and performance statistics collection
period."
Krishnaswamy, Romascanu [Page 13]
Internet Draft PINT MIB July 2000
INDEX {pintServerUserIdName, pintServerServiceTypeIndex,
pintServerPerfStatPeriodIndex}
::= { pintServerUserIdStatsTable 1 }
PintServerUserIdStatsEntry ::= SEQUENCE {
pintServerUserIdName UserIdName,
pintServerUserIdCallsReceived Counter32,
pintServerUserIdSuccessfulCalls Counter32,
pintServerUserIdDisconnectedCalls Counter32,
pintServerUserIdDisconnectedUserIdAuthorizationFailureCalls
Counter32,
pintServerUserIdDisconnectedEgressFacilityProblemCalls Counter32
}
pintServerUserIdName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The unique identifier of the monitored user
identified by its name."
::= { pintServerUserIdStatsEntry 1 }
pintServerUserIdCallsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls received from the specific user."
::= { pintServerUserIdStatsEntry 2 }
pintServerUserIdSuccessfulCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls from the user successfully completed."
::= { pintServerUserIdStatsEntry 3 }
pintServerUserIdDisconnectedCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls received from the user that were
disconnected (failed)."
::= { pintServerUserIdStatsEntry 4 }
Krishnaswamy, Romascanu [Page 14]
Internet Draft PINT MIB July 2000
pintServerUserIdDisconnectedUserIdUserAuthorizationFailureCalls
OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls from the user that were disconnected because of user
authorization failure."
::= { pintServerUserIdStatsEntry 5 }
pintServerUserIdDisconnectedEgressFacilityProblemCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls from the user that were disconnected because of
egress facility problems."
::= { pintServerUserIdStatsEntry 6 }
pintServerGatewayStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF PintServerGatewayStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table displaying the monitored gateway statistics."
::= { pintServerGatewayPerf 1 }
pintServerGatewayStatsEntry OBJECT-TYPE
SYNTAX PintServerGatewayStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries in the gateway table.
One entry is defined for each gateway identified by name,
each monitored service type and performance statistics collection
period."
INDEX { pintRegisteredGatewayName, pintServerServiceTypeIndex,
pintServerPerfStatPeriodIndex
::= { pintServerGatewayStatsTable 1 }
PintServerGatewayStatsEntry ::= SEQUENCE {
pintServerGatewayCallsReceived Counter32,
pintServerGatewaySuccessfulCalls Counter32,
pintServerGatewayDisconnectedCalls Counter32
}
Krishnaswamy, Romascanu [Page 15]
Internet Draft PINT MIB July 2000
pintServerGatewayCallsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls received at the specified gateway."
::= { pintServerGatewayStatsEntry 1 }
pintServerGatewaySuccessfulCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls successfully completed at the specified gateway."
::= { pintServerGatewayStatsEntry 2 }
pintServerGatewayDisconnectedCalls OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of calls that were disconnected (failed) at the specified
gateway."
::= { pintServerGatewayStatsEntry 3 }
--
-- Notifications Section
-- (none defined)
--
--
-- Conformance Section
--
pintMibCompliances OBJECT IDENTIFIER ::= { pintMibConformance 1 }
pintMibGroups OBJECT IDENTIFIER ::= { pintMibConformance 2 }
pintMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
PINT MIB."
MODULE -- this module
MANDATORY-GROUPS { pintMibConfigGroup, pintMibMonitorGroup }
::= { pintMibCompliances 1 }
Krishnaswamy, Romascanu [Page 16]
Internet Draft PINT MIB July 2000
pintMibConfigGroup OBJECT-GROUP
OBJECTS {
pintReleaseNumber,
pintSysContact,
pintApplInstallPkgDescription,
pintRegisteredGatewayName,
pintRegisteredGatewayDescription
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration
information
for a PINT Server."
::= { pintMibGroups 1 }
pintMibMonitorGroup OBJECT-GROUP
OBJECTS {
pintServerServiceTypeIndex,
pintServerPerfStatPeriodIndex,
pintServerGlobalCallsReceived,
pintServerGlobalSuccessfulCalls,
pintServerGlobalDisconnectedCalls,
pintServerGlobalDisconnectedClientUserAuthorizationFailureCalls,
pintServerGlobalDisconnectedServerProblemCalls,
pintServerGlobalDisconnectedGatewayProblemCalls,
pintServerClientAddress,
pintServerClientCallsReceived,
pintServerClientSuccessfulCalls,
pintServerClientDisconnectedCalls,
pintServerClientDisconnectedClientAuthorizationFailureCalls,
pintServerClientDisconnectedEgressFacilityProblemCalls,
pintServerUserIdName,
pintServerUserIdCallsReceived,
pintServerUserIdSuccessfulCalls,
pintServerUserIdDisconnectedCalls,
pintServerUserIdDisconnectedUserIdAuthorizationFailureCalls,
pintServerUserIdDisconnectedEgressFacilityProblemCalls,
pintServerGatewayCallsReceived,
pintServerGatewaySuccessfulCalls,
pintServerGatewayDisconnectedCalls
}
STATUS current
DESCRIPTION
"A collection of objects providing monitoring
information
for a PINT Server."
::= { pintMibGroups 2 }
Krishnaswamy, Romascanu [Page 17]
Internet Draft PINT MIB July 2000
END
6. Acknowledgements
The authors would like to thank Igor Faynberg for his encouragement
to produce this work.
7. Security Considerations
There is only one management object defined in this MIB that has a
MAX-ACCESS clause of read-write (pintSysContact). There are no read-
create objects. This read-write object may be considered sensitive or
vulnerable in some network environments. The support for SET opera-
tions in a non-secure environment without proper protection can have
a negative effect on network operations.
There are a number of managed objects in this MIB that may contain
information that may be sensitive from a business perspective. One
could be the customer identification (UserIdName). Also information
on PINT services performance might itself be need to be guarded. It
is thus important to control even GET access to these objects and
possibly to even encrypt the values of these object when sending them
over the network via SNMP. Not all versions of SNMP provide features
for such a secure environment.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security fea-
tures as provided by the SNMPv3 framework. Specifically, the use of
the User-based Security Model RFC 2574 [13] and the View- based
Access Control Model RFC 2575 [16] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly config-
ured to give access to the objects only to those principals (users)
that have legitimate rights to indeed GET or SET (change/cre-
ate/delete) them.
8. IANA Considerations
All extensions to the values listed in this MIB must be done through
Krishnaswamy, Romascanu [Page 18]
Internet Draft PINT MIB July 2000
Standards Action processes as defined in RFC 2434 [21].
9. References
[1] H.Lu, et. al, "Toward the PSTN/Internet Inter-Networking --Pre-
PINT Implementations", RFC 2458, November 1998.
[2] Wijnen, B., Harrington, D., and Presuhn, R., "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, April 1999.
[3] Rose, M. and McCloghrie, K., "Structure and Identification of Man-
agement Information for TCP/IP-based Internets", RFC 1155, May
1990.
[4] Rose, M. and McCloghrie, K., "Concise MIB Definitions", RFC 1212,
March 1991.
[5] Rose, M., "A Convention for Defining Traps for use with the SNMP",
RFC 1215, March 1991.
[6] McCloghrie, K., Perkins, D., and Schoenwaelder, J., "Structure of
Management Information Version 2 (SMIv2)", RFC 2578, April 1999.
[7] McCloghrie, K., Perkins, D., and Schoenwaelder, J., "Textual Con-
ventions for SMIv2", RFC 2579, April 1999.
[8] McCloghrie, K., Perkins, D., and Schoenwaelder, J., "Conformance
Statements for SMIv2", RFC 2580, April 1999.
[9] Case, J., Fedor, M., Schoffstall, M., and Davin, J., "Simple Net-
work Management Protocol", RFC 1157, May 1990.
[10] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S., "Introduc-
tion to Community-based SNMPv2", RFC 1901, January 1996.
[11] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S., "Transport
Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996.
[12] Case, J., Harrington D., Presuhn R., and Wijnen, B., "Message Pro-
cessing and Dispatching for the Simple Network Management Protocol
(SNMP)", RFC 2572, April 1999.
[13] Blumenthal, U. and Wijnen, B., "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol (SNMPv3)",
RFC 2574, April 1999.
Krishnaswamy, Romascanu [Page 19]
Internet Draft PINT MIB July 2000
[14] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S., "Protocol
Operations for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, January 1996.
[15] Levi, D., Meyer, P., and Stewart, B., "SNMPv3 Applications", RFC
2573, April 1999.
[16] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999.
[17] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to
Version 3 of the Internet-standard Network Management Framework",
RFC 2570, April 1999.
[18] S. Petrack, L. Conroy, "The PINT Service Protocol: Extensions to
SIP and SDP for IP Access to Telephone Call Services", draft-ietf-
pint-protocol-01.txt, 14 July 1999.
[19] C. Krupczak, J. Saperia, "Definitions of System-Level Managed
Objects for Applications", RFC 2287, February 1998.
[20] D. Harrington, R. Presuhn, B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2271, January 1998.
[21] T. Narten, H. Alvestrand, "Guidelines for Writing an IANA Consid-
erations Section in RFCs", RFC 2434, October 1998.
10. Authors' Addresses
Murali Krishnaswamy
Lucent Technologies
3C-512, 101 Crawfords Corner Rd.
Holmdel, NJ 07733
Tel: +1 (732)949-3611
Fax: +1 (732)949-3210
E-mail: murali@lucent.com
Dan Romascanu
Avaya Communication
Atidim Technology Park, Bldg 3
Tel Aviv, Israel
Tel: +972 3 6458414
E-mail: dromasca@lucent.com
Krishnaswamy, Romascanu [Page 20]
