PWE3 Working Group Andrew G. Malis
Internet Draft Tellabs
Expiration Date: October 2004
Prayson Pate
Overture Networks
Ron Cohen (Editor)
Lycium Networks
David Zelig
Corrigent Systems
April 2004
SONET/SDH Circuit Emulation over Packet (CEP)
draft-ietf-pwe3-sonet-05.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of section 10 of [RFC2026].
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
The generic requirements and architecture for Pseudo Wire Emulation
Edge-to-Edge (PWE3) have been described in [PWE3-REQ] and [PWE3-
ARCH]. Additional requirements for emulation of SONET/SDH and
lower-rate TDM circuits have been defined in [PWE3-TDM-REQ].
This draft provides encapsulation formats and semantics for
emulating SONET/SDH circuits and services over a packet-switched
network (PSN).
pwe3-sonet Expires October 2004 [Page 1]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Co-Authors
The following individuals are co-authors of this document. Tom
Johnson from Litchfield Communication did most of the editing work
for pre WG versions of the SONET SPE work up to version 01 of this
document.
Craig White Level3 Communications
Ed Hallman Litchfield Communications
Jeremy Brayley Laurel Networks
Jim Boyle Juniper Networks
John Shirron Laurel Networks
Luca Martini Cisco Systems
Marlene Drost Litchfield Communications
Steve Vogelsang Laurel Networks
Tom Johnson Litchfield Communications
Ken Hsu Tellabs
pwe3-sonet Expires December 2003 [Page 2]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Table of Contents
1 CONVENTIONS USED IN THIS DOCUMENT.................3
2 ACRONYMS..........................................4
3 SCOPE.............................................5
4 CEP ENCAPSULATION FORMAT..........................6
4.1 SONET/SDH Fragment...............................7
4.2 CEP Header.......................................9
4.3 RTP Header......................................11
4.4 PSN Encapsulation...............................12
5 CEP OPERATION....................................16
5.1 CEP Packetizer and De-Packetizer................16
5.2 Packet Synchronization..........................17
6 SONET/SDH MAINTENANCE SIGNALS....................19
6.1 SONET/SDH to PSN................................19
6.2 PSN to SONET/SDH................................21
7 SONET/SDH TRANSPORT TIMING.......................23
8 SONET/SDH POINTER MANAGEMENT.....................23
8.1 Explicit Pointer Adjustment Relay (EPAR)........23
8.2 Adaptive Pointer Management (APM)...............24
9 CEP PERFORMANCE MONITORS.........................25
9.1 Near-End Performance Monitors...................25
9.2 Far-End Performance Monitors....................26
10 PAYLOAD COMPRESSION OPTIONS.....................27
10.1 Dynamic Bandwidth Allocation...................27
10.2 Service-Specific Payload Formats...............27
11 SIGNALING OF CEP PSEUDO WIRES...................37
11.1 CEP/TDM Payload Bytes..........................37
11.2 CEP/TDM Bit Rate...............................38
11.3 CEP Options....................................38
12 SECURITY CONSIDERATIONS.........................40
13 INTELLECTUAL PROPERTY DISCLAIMER................40
14 REFERENCES......................................40
15 AUTHORS ADDRESSES..............................42
Appendix A SONET/SDH Rates and Formats..............44
Appendix B Example Network Diagrams.................46
Full Copyright Statement............................48
Acknowledgement.....................................48
1 Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC 2119].
pwe3-sonet Expires December 2003 [Page 3]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
2 Acronyms
ADM Add Drop Multiplexer
AIS Alarm Indication Signal
APM Adaptive Pointer Management
AU-n Administrative Unit-n (SDH)
AUG Administrative Unit Group (SDH)
BIP Bit Interleaved Parity
BITS Building Integrated Timing Supply
CEP Circuit Emulation over Packet
DBA Dynamic Bandwidth Allocation
EBM Equipped Bit Mask
EPAR Explicit Pointer Adjustment Relay
LOF Loss of Frame
LOS Loss of Signal
LTE Line Terminating Equipment
PSN Packet Switched Network
POH Path Overhead
PTE Path Terminating Equipment
PW Pseudo-Wire
PWE3 Pseudo-Wire Emulation Edge-to-Edge
RDI Remote Defect Indication
SDH Synchronous Digital Hierarchy
SONET Synchronous Optical Network
STM-n Synchronous Transport Module-n (SDH)
STS-n Synchronous Transport Signal-n (SONET)
TDM Time Division Multiplexing
TOH Transport Overhead
TU-n Tributary Unit-n (SDH)
TUG-n Tributary Unit Group-n (SDH)
UNEQ Unequipped
VC-n Virtual Container-n (SDH)
VT Virtual Tributary (SONET)
VTG Virtual Tributary Group (SONET)
pwe3-sonet Expires December 2003 [Page 4]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
3 Scope
This document describes how to emulate the following digital signals
over a packet switched network:
1. Synchronous Payload Envelope (SPE): STS-1/VC-3, STS-3c/VC-4, STS-
12c/VC-4-4c, STS-48c/VC-4-16c, STS-192c/VC-4-64c.
2. Virtual Tributary (VT): VT1.5/VC-11, VT2/VC-12, VT3, VT6/VC-2
For the remainder of this document, these constructs will be
referred to as SONET/SDH channels.
Although this document currently covers up to OC-192c/VC-4-64c,
future revision MAY address higher rates.
pwe3-sonet Expires December 2003 [Page 5]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
4 CEP Encapsulation Format
In order to transport SONET/SDH circuits through a packet-oriented
network, the SPE (or VT) is broken into fragments, and a CEP Header
is pre-pended to each fragment. The resulting packet is
encapsulated in RTP for transmission over an arbitrary PSN. The RTP
header location differs for MPLS PSNs. See section 4.4.2 for
details.
Under certain circumstances the RTP header may be suppressed to
conserve network bandwidth (See section 4.4.4 for details).
The basic CEP packet appears in Figure 1.
+-----------------------------------+
| PSN and Multiplexing Layer |
| Headers |
+-----------------------------------+
| RTP Header |
| (RFC1889) |
+-----------------------------------+
| CEP Header |
+-----------------------------------+
| |
| |
| SONET/SDH |
| Fragment |
| |
| |
+-----------------------------------+
Figure 1 - Basic CEP Packet
pwe3-sonet Expires December 2003 [Page 6]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
4.1 SONET/SDH Fragment
The SONET/SDH Fragments MUST be byte aligned with the SONET/SDH SPE
or VT.
The first bit received from each byte of the SONET/SDH MUST be the
Most Significant Bit of each byte in the SONET/SDH fragment.
SONET/SDH bytes are placed into the SONET/SDH fragment in the same
order in which they are received.
SONET/SDH optical interfaces use binary coding and therefore are
scrambled prior to transmission to insure an adequate number of
transitions. For clarity, this scrambling will be referred to as
physical layer scrambling/descrambling.
In addition, many payload formats (such as for ATM and HDLC) include
an additional layer of scrambling to provide protection against
transition density violations within the SPEs. This function will
be referred to as payload scrambling/descrambling.
CEP assumes that physical layer scrambling/descrambling occurs as
part of the SONET/SDH section/line termination Native Service
Processing (NSP) functions.
However, CEP makes no assumption about payload scrambling. The
SONET/SDH fragments MUST be constructed without knowledge or
processing of any incidental payload scrambling.
CEP implementations MUST include the H3 (or V3) byte in the
SONET/SDH fragment during negative pointer adjustment events, and
MUST remove the stuff-byte from the SONET/SDH fragment during
positive pointer adjustment events.
VT emulation implementations MUST NOT carry the VT pointer bytes V1,
V2, V3 and V4 as part of the CEP payload. The only exception being
carriage of V3 during negative pointer adjustment as described
above.
All CEP SPE Implementations MUST support a packet size of 783 Bytes
and MAY support other packet sizes.
VT emulation implementations MUST support payload size of full VT
super-frame, and MAY support 1/2 and 1/4 VT super-frame payload
sizes.
pwe3-sonet Expires December 2003 [Page 7]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Table 1 below describes single super-frame payload size per VT type.
+-------------+-------------+
| VT type | size |
+-------------+-------------+
| VT1.5/VC-11 | 104 bytes |
| VT2/VC-12 | 140 bytes |
| VT3 | 212 bytes |
| VT6/VC-2 | 428 bytes |
+-------------+-------------+
Table 1 - VT Super-frame Payload Sizes
OPTIONAL SONET/SDH Fragment formats have been defined to reduce the
bandwidth requirements of the emulated SONET/SDH circuits under
certain conditions. These OPTIONAL Formats are included in
Section 10.
pwe3-sonet Expires December 2003 [Page 8]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
4.2 CEP Header
The CEP Header supports a basic and extended mode. The Basic CEP
Header provides the minimum functionality necessary to accurately
emulate a SONET/SDH circuit over a PSN.
Enhanced functionality and commonality with other real-time Internet
applications is provided by RTP encapsulation.
Bit 0 of the first 32-bit CEP header indicates whether or not the
extended header is present. When this bit is 0, then no extended
header is present. When this bit is 1, then an extended header is
present. Extended headers are utilized for the some of the OPTIONAL
SONET/SDH fragment formats described in Section 10.
The Basic CEP header has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|R|D|N|P| Structure Pointer[0:12] | Sequence Number[0:13] |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2 - Basic CEP Header Format
The above fields are defined as follows:
R bit: CEP-RDI. This bit is set to one to signal to the remote CEP
function that a loss of packet synchronization has occurred.
D bit: Signals DBA Mode. The D bit MUST be set to zero for Normal
Operation. It MUST be set to one if CEP is currently in DBA mode.
DBA is an optional mode during which trivial payloads are not
transmitted into the packet network. See Table 2 and section 10.1
for further details.
The N and P bits: MAY be used to explicitly relay negative and
positive pointer adjustment events across the PSN. They are also
used to relay SONET/SDH maintenance signals such as AIS-P/V. See
Table 2 and section 8.1 for more details.
pwe3-sonet Expires December 2003 [Page 9]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
+---+---+---+----------------------------------------------+
| D | N | P | Interpretation |
+---+---+---+----------------------------------------------+
| 0 | 0 | 0 | Normal Mode No Ptr Adjustment |
| 0 | 0 | 1 | Normal Mode Positive Ptr Adjustment |
| 0 | 1 | 0 | Normal Mode Negative Ptr Adjustment |
| 0 | 1 | 1 | Normal Mode AIS-P/V |
| | | | |
| 1 | 0 | 0 | DBA Mode UNEQ-P/V |
| 1 | 0 | 1 | DBA Mode UNEQ-P/V Positive Ptr Adj |
| 1 | 1 | 0 | DBA Mode UNEQ-P/V Negative Ptr Adj |
| 1 | 1 | 1 | DBA Mode AIS-P/V |
+---+---+---+----------------------------------------------+
Table 2 - Interpretation of D, N, and P bits
Sequence Number [0:13]: This is a packet sequence number, which
MUST continuously cycle from 0 to 0x3FFF. It is generated and
processed in accordance with the rules established in [RFC1889].
When the RTP header is used, this sequence number MUST match the
LSBs of the RTP sequence Number.
Structure Pointer [0:12]: The Structure Pointer MUST contain the
offset of the first byte of the payload structure. For SPE
emulation, the structure pointer locates the J1 byte within the CEP
SONET/SDH Fragment. For VT emulation the structure pointer locates
the V5 byte within the SONET/SDH fragment. The value is from 0 to
0x1FFE, where 0 means the first byte after the CEP header. The
Structure Pointer MUST be set to 0x1FFF if a packet does not carry
the J1 (or V5) byte.
pwe3-sonet Expires December 2003 [Page 10]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
4.3 RTP Header
CEP uses the RTP Header as shown below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
Figure 3 - RTP Header
V : Version. The Version field MUST be set to 2.
P : Padding. No padding is required. The P bit MUST be set to 0.
X : Header extension. No extensions are defined. The X bit MUST be
set to 0.
CC: CSRC count. CC field MUST be set to zero.
M : Marker. The M bit MUST be set to 0 for CEP packets.
PT [0:6]: Payload type. The payload type is used to identify CEP
packets. A PT value SHOULD be allocated from the range of dynamic
values for every CEP pseudo-wire. Allocation is done during the
pseudo-wire setup and MUST be the same for both pseudo-wire
directions.
Sequence Number [0:15]: The sequence number provides the common PW
sequencing function as well as detection of lost packets. It is
generated and processed in accordance with the rules established in
[RFC1889].
Timestamp [0:31]: The time stamp is used primarily for carrying
timing information over the network. Their values are used in
accordance with the rules established in [RFC1889]. Frequency of
the clock used for generating timestamps MUST be 19.44 MHz based on
a local reference.
SSRC [0:31]: Synchronization source. The SSRC field MAY be used for
detection of misconnections.
pwe3-sonet Expires December 2003 [Page 11]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
4.4 PSN Encapsulation
In principle, CEP packets can be carried over any packet-oriented
network. The following sections describe specifically how CEP
packets are encapsulated for carriage over MPLS or IP networks.
4.4.1 IP Encapsulation
CEP uses the standard IP/UDP/RTP encapsulation scheme as shown
below. The UDP destination port MUST be used to De-multiplex
individual CEP channels. RTP header MAY be suppressed to conserve
network bandwidth (See section 4.4.4 for details).
+-----------------------------------+
| |
| IPv6/v4 Header |
| |
+-----------------------------------+
| UDP Header |
+-----------------------------------+
| RTP Header |
+-----------------------------------+
| CEP Header |
+-----------------------------------+
| |
| |
| SONET/SDH Fragment |
| |
| |
+-----------------------------------+
Figure 4 - IP Transport Encapsulation
pwe3-sonet Expires December 2003 [Page 12]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
4.4.2 MPLS Encapsulation
Figure 5 describes CEP encapsulation over an MPLS network. To
transport a CEP packet over an MPLS network, an MPLS label-stack
MUST be pushed on top of the CEP packet. The bottom label in the
MPLS label stack MUST be used to de-multiplex individual CEP
channels. In keeping with the conventions used in [PWE3-CONTROL],
this de-multiplexing label is referred to as the PW Label and the
upper labels are referred to as Tunnel Labels.
To allow accurate packet inspection in an MPLS PSN, and/or to
operate correctly over MPLS networks that have deployed equal-cost
multiple-path load-balancing (ECMP), a PW packet SHOULD not alias an
IP packet. Since the CEP header's first 4 bits are used to carry CEP
signaling and therefore may alias an IP packet, a CEP MPLS
adaptation header is added. The CEP MPLS adaptation header format is
defined in Figure 6 . The CEP MPLS adaptation header MAY be
suppressed in MPLS networks where IP aliasing is not a problem.
RTP header immediately follows the PW CEP header. RTP header MAY be
suppressed to conserve network bandwidth (See section 4.4.4 for
details).
+-----------------------------------+
| One or more MPLS Tunnel Labels |
+-----------------------------------+
| PW Label |
+-----------------------------------+
| CEP MPLS Adaptation Header |
+-----------------------------------+
| CEP Header |
+-----------------------------------+
| RTP Header |
+-----------------------------------+
| |
| |
| SONET/SDH Fragment |
| |
| |
+-----------------------------------+
Figure 5 - MPLS Transport Encapsulation
pwe3-sonet Expires December 2003 [Page 13]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6 - CEP MPLS Adaptation Header
First four bits of the CEP MPLS Adaptation Header are set to zero.
The rest of the bits are reserved for future use. The reserved bits
MUST be set to zero by transmitter and ignored by the receiver.
4.4.3 L2TPv3 Encapsulation
Figure 7 describes CEP encapsulation over Layer 2 Tunneling Protocol
version 3 [L2TPv3]. RTP header may be suppressed to conserve network
bandwidth (See section 4.4.4 for details). The L2TPv3 header MUST
be used to de-multiplex individual CEP channels.
+-----------------------------------+
| L2TPv3 Header |
+-----------------------------------+
| RTP Header |
+-----------------------------------+
| CEP Header |
+-----------------------------------+
| |
| |
| SONET/SDH Fragment |
| |
| |
+-----------------------------------+
Figure 7 - L2TPv3 Transport Encapsulation
pwe3-sonet Expires December 2003 [Page 14]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
CEP uses the L2TPv3 header as defined below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Session ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cookie |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cookie (Long) |
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
Figure 8 - L2TPv3 Header
Session ID: Used to de-multiplex individual CEP channels
Cookie: Optional 0/32/64 bit field. The cookie MAY be used for
detection of misconnections. Cookie field is suppressed by default.
Use of the Cookie field and its length may be statically configured
or signaled using [L2TPv3].
4.4.4 RTP Header Suppression
In addition to normal RTP header compression mechanisms as described
in [RFC2508] and [RFC3095], an additional option may be used in CEP
which suppresses transmission of the RTP header altogether.
pwe3-sonet Expires December 2003 [Page 15]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
5 CEP operation
CEP MUST support a normal mode of operation and MAY support
additional bandwidth conserving modes described in section 10.
During normal operation, SONET/SDH payloads are fragmented, pre-
pended with the appropriate headers and then transmitted into the
packet network.
5.1 CEP Packetizer and De-Packetizer
As with all adaptation functions, CEP has two distinct components:
adapting TDM SONET/SDH into a CEP packet stream, and converting the
CEP packet stream back into a TDM SONET/SDH. The first function
will be referred to as CEP Packetizer and the second as CEP De-
Packetizer. This terminology is illustrated in Figure 9.
+------------+ +---------------+
| | | |
SONET --> | CEP | --> PSN --> | CEP | --> SONET
SDH | Packetizer | | De-Packetizer | SDH
| | | |
+------------+ +---------------+
Figure 9 - CEP Terminology
Note: the CEP de-packetizer requires a buffering mechanism to
account for delay variation in the CEP packet stream. This
buffering mechanism will be generically referred to as the CEP
jitter buffer.
During normal operation, the CEP packetizer will receive a fixed
rate byte stream from a SONET/SDH interface. When a packet worth
of data has been received from a SONET/SDH channel, the necessary
headers are pre-pended to the SPE fragment and the resulting CEP
packet is transmitted into the packet network. Because all CEP
packets associated with a specific SONET/SDH channel will have the
same length, the transmission of CEP packets for that channel SHOULD
occur at regular intervals.
At the far end of the packet network, the CEP de-packetizer will
receive packets into a jitter buffer and then play out the received
byte stream at a fixed rate onto the corresponding SONET/SDH
channel. The jitter buffer SHOULD be adjustable in length to
account for varying network delay behavior. The receive packet rate
from the packet network should be exactly balanced by the
transmission rate onto the SONET/SDH channel, on average. The time
over which this average is taken corresponds to the depth of the
jitter buffer for a specific CEP channel.
pwe3-sonet Expires December 2003 [Page 16]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
The RTP sequence numbers provide a mechanism to detect lost and/or
mis-ordered packets. The sequence number in the CEP header MUST be
used when transmission of the RTP header is suppressed (see 4.4.4
for details). The CEP de-packetizer MUST detect lost or miss-
ordered packets. The CEP de-packetizer SHOULD play out an all ones
pattern (AIS) in place of any dropped packets. The CEP de-
packetizer MAY re-order packets received out of order. If the CEP
de-packetizer does not support re-ordering, it MUST drop miss-
ordered packets.
5.2 Packet Synchronization
A key component in declaring the state of a CEP service is whether
or not the CEP de-packetizer is in or out of packet synchronization.
The following paragraphs describe how that determination is made.
As packets are received from the PSN, they are placed into a jitter
buffer prior to play out on the SONET/SDH interface. If a CEP de-
packetizer supports re-ordering, any packet received before its play
out time will still be considered valid.
If a CEP de-packetizer does not support re-ordering, a number of
approaches may be used to minimize the impact of miss-ordered or
lost packets on the final re-assembled SONET/SDH stream. For
example, [AAL1] uses a simple state-machine to re-order packets in a
sub-set of possible cases.
However, the final determination as to whether or not to declare
acquisition or loss of packet synchronization MUST be based on the
same criteria regardless of whether an implementation supports or
does not support re-ordering.
Therefore, the determination of acquisition or loss of packet
synchronization is always made at SONET/SDH play-out time. During
SONET/SDH play-out, the CEP de-packetizer will play received CEP
packets onto the SONET/SDH interface. However, if the jitter buffer
is empty or the packet to be played out has not been received, the
CEP de-packetizer will play out an empty packet onto the SONET/SDH
interface in place of the unavailable packet.
The acquisition of packet synch is based on the number of sequential
CEP packets that are played onto the SONET/SDH interface. Loss of
packet synch is based on the number of sequential 'empty' packets
that are played onto the SONET/SDH interface. Specific details of
these two cases are described below.
pwe3-sonet Expires December 2003 [Page 17]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
5.2.1 Acquisition of Packet Synchronization
At startup, a CEP de-packetizer will be out of packet
synchronization by default. To declare packet synchronization at
startup or after a loss of packet synchronization, the CEP de-
packetizer must play-out a configurable number of CEP packets with
sequential sequence numbers towards the SONET/SDH interface.
5.2.2 Loss of Packet Synchronization
Once a CEP de-packetizer is in packet sync, it may encounter a set
of events that will cause it to lose packet synchronization.
If the CEP de-packetizer encounters more than a configurable number
of sequential empty packets, the CEP de-packetizer MUST declare loss
of packet synchronization (LOPS) defect.
Loss of Packet Synchronization (LOPS) failure is declared after 2.5
+/- 0.5 seconds of LOPS defect, and cleared after 10 seconds free of
LOPS defect state. The circuit is considered down as long as LOPS
failure is declared.
pwe3-sonet Expires December 2003 [Page 18]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
6 SONET/SDH Maintenance Signals
This section describes mapping of maintenance and alarm signals
between the SONET/SDH network and the CEP pseudo-wire. For clarity,
the mappings are split into two groups: SONET/SDH to PSN, and PSN to
SONET/SDH.
For coherent failure detection, isolation, monitoring and trouble
shooting, SONET/SDH failure indications MUST be transferred
correctly over the CEP pseudo-wire, and CEP connection failures MUST
be mapped to SONET/SDH PATH/VT failure indications.
6.1 SONET/SDH to PSN
The following sections describe how SONET/SDH Maintenance Signals
and Alarm conditions are mapped into a CEP pseudo-wire.
6.1.1 AIS-P/V Indication
SONET/SDH Path outages are signaled using maintenance alarms such as
Path AIS (AIS-P). In particular, AIS-P indicates that the SONET/SDH
Path is not currently transmitting valid end-user data, and the SPE
contains all ones. Similarly, AIS-V indicates that the VT is not
currently transmitting valid end-user data, and the VT contains all
ones.
It should be noted that nearly every type of service-affecting
section or line defect would result in an AIS-P/V condition.
The mapping of SONET/SDH failures into the PATH/VT layer is
considered part of the NSP function, and is based on the principles
specified in [GR253] and [G.707]. Should the Section Layer detect a
Loss of Signal (LOS) or Loss of Frame (LOF) conditions, it sends
AIS-L up to the Line Layer. If the Line Layer detects AIS-L or Loss
of Path (LOP), it sends AIS-P to the Path Layer. If the Path layer
detects AIS-P and is terminated at the NSP, it sends AIS-V to the VT
Layer.
The AIS-P indication is transferred to the CEP packetizer. During
AIS-P, SPE CEP packets are generated as usual. The N and P bits MUST
be set to 11 binary to signal AIS-P explicitly through the packet
network. The D-bit MUST be set to zero to indicate that the SPE is
being carried through the packet network. Normal CEP packets with
the SPE fragment, CEP Header, the Circuit ID Word, and PSN Header
MUST be transmitted into the packet network. If DBA has been enabled
for AIS SPE/VT the D-bit MUST be set to one to indicate DBA is
active and only the necessary headers and optional padding are
transmitted into the packet network. The same rules are followed for
VT CEP packets during AIS-V condition.
pwe3-sonet Expires December 2003 [Page 19]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
6.1.2 Unequipped Indication
The declaration of SPE/VT unequipped MUST conform to [GR253].
Unequipped indication is used for DBA bandwidth conserving mode as a
trigger for payload removal.
STS PTE shall detect an STS Path Unequipped (UNEQ-P) defect within
10 ms of the onset of at least five consecutive samples (which may
or may not be consecutive frames) of unequipped STS Signal Labels
(C2 byte). STS PTE shall terminate an UNEQ-P defect within 10 ms of
the onset of at least five consecutive samples (which may or may not
be consecutive frames) of STS Signal Labels that are not unequipped
or all-ones. Similar rules apply to detection and termination of VT
Unequipped (UNEQ-V) defects.
During SPE/VT Unequipped, the N and P bits MUST be interpreted as
usual. The SPE/VT MUST be transmitted into the packet network along
with the appropriate headers, and the D-Bit MUST be set to zero.
If DBA has been enabled for Unequipped SPE/VT the D-bit MUST be set
to one to indicate DBA is active and only the necessary headers and
optional padding are transmitted into the packet network. The N and
P bits MAY be used to signal pointer adjustments as normal.
6.1.3 CEP-RDI
The CEP function MUST send CEP-RDI towards the packet network during
loss of packet synchronization. This MUST be accomplished by
setting the R bit to one in the CEP header.
pwe3-sonet Expires December 2003 [Page 20]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
6.2 PSN to SONET/SDH
The following sections discuss how the various conditions on the
packet network are converted into SONET/SDH indications.
The SONET/SDH hierarchy combined with CEP is illustrated below.
+----------+
| VT |
+----------+
^ ^
| |
| LOPS
| | +------------+
| +-----| CEP VT PW |
| +------------+
AIS-V
|
+----------+
| PATH |
+----------+
^ ^
| |
| LOPS
| | +------------+
| +-----| CEP SPE PW |
| +------------+
---------------- | -----------------------
^
AIS-P
NSP |
+----------+
| LINE |
+ ---------+
^ ^
| |
AIS-L +------ LOP
|
+----------+
| SECTION |
+----------+
^ ^
| |
LOS LOF
Figure 10 - SONET/SDH and CEP AIS Fault Hierarchy
pwe3-sonet Expires December 2003 [Page 21]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
6.2.1 AIS-P/V Indication
There are several conditions in the packet network that will cause
the CEP de-packetization function to play out an AIS-P/V indication
towards a SONET/SDH channel.
The first of these is the receipt of CEP packets with the N and P
bits set to one. This is an explicit indication of AIS-P or AIS-V
being received at the far-end of the packet network. The CEP de-
packetizer MUST play out one packet's worth of all ones for each
packet received, and MUST set the SONET/SDH Overhead to signal AIS-
P/V as defined in [SONET], [GR253] and [G707].
The second case that will cause a CEP de-packetization function to
play out an AIS-P indication onto a SONET/SDH channel is during loss
of packet synchronization. In this case, the CEP de-packetizer MUST
set the SONET/SDH Overhead to signal AIS-P/V as defined in [SONET],
[GR253] and [G707].
6.2.2 Unequipped Indication
There are several conditions in the packet network that will cause
the CEP function to transmit Unequipped indications onto the
SONET/SDH channel.
The first, which is transparent to CEP, is the receipt of regular
CEP packets that happen to be carrying an SPE that contains the
appropriate Path overhead or VT overhead set to unequipped. This
case does not require any special processing on the part of the CEP
de-packetizer.
The second case is the receipt of CEP packets that have the D-bit
set to one to indicate DBA active and the N and P bits set to 00
binary, 01 binary, or 10 binary to indicate SPE Unequipped with or
without pointer adjustments. The CEP de-packetizer MUST use this
information to transmit a packet of all zeros onto the SONET/SDH
interface, and adjust the payload pointer as necessary.
The third case when a CEP de-packetizer MUST play out an SPE/VT
Unequipped Indication towards the SONET/SDH interface is when the
circuit has been de-provisioned.
pwe3-sonet Expires December 2003 [Page 22]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
7 SONET/SDH Transport Timing
It is assumed that the distribution of SONET/SDH Transport timing
information is addressed either through external mechanisms such as
Building Integrated Timing System (BITS), Stand Alone
Synchronization Equipment (SASE), Global Positioning System (GPS) or
other such methods, or is through an adaptive timing recovery
mechanism.
8 SONET/SDH Pointer Management
A pointer management system is defined as part of the definition of
SONET/SDH. Details on SONET/SDH pointer management can be found in
[SONET], [GR253] and [G707]. If there is a frequency offset between
the frame rate of the transport overhead and that of the SONET/SDH
SPE or VT, then the alignment of the SPE (or VT) will periodically
slip back or advance in time through positive or negative stuffing.
The emulation of this aspect of SONET/SDH networks may be
accomplished using a variety of techniques including (but not
limited to) explicit pointer adjustment relay (EPAR) and adaptive
pointer management (APM).
In any case, the handling of the SPE data by the CEP packetizer is
the same.
During a negative pointer adjustment event, the CEP packetizer MUST
incorporate the H3 (or V3) byte from the SONET/SDH stream into the
CEP packet payload in order with the rest of the SPE. During a
positive pointer adjustment event, the CEP packetizer MUST strip the
stuff byte from the CEP packet payload.
When playing out a negative pointer adjustment event, the
appropriate byte of the CEP payload MUST be placed into the H3 (or
V3) byte of the SONET/SDH stream. When playing out a positive
pointer adjustment, the CEP de-packetizer MUST insert a stuff-byte
into the appropriate position within the SONET/SDH stream.
The details regarding the use of the H3 (and V3) byte and stuff byte
during positive and negative pointer adjustments can be found in
[SONET], [GR253] and [G707].
8.1 Explicit Pointer Adjustment Relay (EPAR)
CEP provides an OPTIONAL mechanism to explicitly relay pointer
adjustment events from one side of the PSN to the other. This
technique will be referred to as Explicit Pointer Adjustment Relay
(EPAR). EPAR is only effective when both ends of the PW have access
to a common timing reference.
pwe3-sonet Expires December 2003 [Page 23]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
The following text only applies to implementations that choose to
implement EPAR. Any CEP implementation that does not support EPAR
MUST either set the N and P bits to zero or utilize them to relay
AIS-P/V and STS/VT Unequipped as shown in Table 2.
When working in EPAR mode, it is assumed that a common reference
clock is available for both the de-packetizer and the packetizer.
The CEP service relay the pointer adjustments which represents the
difference between the SPE/VT frequency and the reference clock,
keeping the SPE/VT payload rate equal at the de-packetizer and
packetizer outputs.
The mechanics of EPAR are described below.
For SPE Emulation, the pointer adjustment event MUST be transmitted
in three consecutive packets by the packetizer. The de-packetizer
MUST play out the pointer adjustment event when any one packet with
N/P bit set is received.
The CEP de-packetizer MUST utilize the CEP sequence numbers to
insure that SONET/SDH pointer adjustment events are not played any
more frequently than once per every three CEP packets transmitted by
the remote CEP packetizer.
For VT emulation, a pointer adjustment event MUST be transmitted in
all packets carrying a single VT super-frame, starting from the
packet carrying the V5 byte and not including the packet carrying
the V5 byte of the next VT super-frame. Pointer adjustment events at
the VT and STS-1 levels are mapped to N and P indications. Pointer
adjustments at the VT level are mapped 1:1 to CEP indications, while
SPE pointer indications are mapped according to the ratio of VT/SPE
byte rates.
If both bits are set, then an AIS-P/V event has been detected at the
PW ingress, making the pointer invalid.
When DBA is invoked (i.e. the D-bit = 1), N and P have additional
meanings. See Table 2 and section 10.1 for more details.
8.2 Adaptive Pointer Management (APM)
Another OPTIONAL method that may be used to emulate SONET/SDH
pointer management is Adaptive Pointer Management (APM). In basic
terms, APM uses information about the depth of the CEP jitter
buffers to introduce pointer adjustments in the reassembled
SONET/SDH SPE.
Details about specific APM algorithms are not considered to be
within scope for this document.
pwe3-sonet Expires December 2003 [Page 24]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
9 CEP Performance Monitors
SONET/SDH as defined in [SONET], [GR253] and [G707] includes the
definition of several counters that may be used to monitor the
performance of SONET/SDH services. These counters are referred to
as Performance Monitors.
In order for CEP to be utilized by traditional SONET/SDH network
operators, CEP SHOULD provide similar functionality. To this end,
the following sections describe a number of counters that will
collectively be referred to as CEP Performance Monitors.
9.1 Near-End Performance Monitors
These performance monitors are maintained by the CEP De-Packetizer
during reassembly of the SONET/SDH stream.
The performance monitors are based on two types of defects.
Type 1 : missing or dropped packet.
Type 2 : buffer under run, buffer over-run, LOPS, missing packets
above pre-defined configurable threshold.
The specific performance monitors defined for CEP are as follows:
ES-CEP - CEP Errored Seconds
SES-CEP - CEP Severely Errored Seconds
UAS-CEP - CEP Unavailable Seconds
Each second that contain at least one type 1 defect SHALL be
declared as ES-CEP. Each second that contain at least one type 2
defect SHALL be declared as SES-CEP.
UAS-CEP SHALL be declared after configurable number of consecutives
SES-CEP, and cleared after a configurable number of consecutive
seconds without SES-CEP. Default value for each is 10 seconds.
Once unavailability is declared, ES and SES counts SHALL be
inhibited up to the point where the unavailability was started. Once
unavailability is removed, ES that occurred along the X seconds
clearing period SHALL be added to the ES counts.
pwe3-sonet Expires December 2003 [Page 25]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
9.2 Far-End Performance Monitors
Far-End performance monitors provide insight into the CEP De-
packetizer at the far-end of the PSN.
Far end statistics are based on the RDI-CEP bit. CEP-FE defect is
declared when CEP-RDI is set in the incoming CEP packets.
CEP-FE failure declared after 2.5 +/- 0.5 seconds of CEP-FE defect,
and cleared after 10 seconds free of CES-FE defect state. Sending
notification to the OS for CEP-FE failure is local policy.
pwe3-sonet Expires December 2003 [Page 26]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
10 Payload Compression Options
In addition to pure emulation, CEP also offers a number of options
for reducing the total bandwidth utilized by the emulated circuit.
These options fall into two categories: Dynamic Bandwidth Allocation
and Service-Specific Payload Formats.
Dynamic Bandwidth Allocation (DBA) suppresses transmission of the
CEP payload altogether under certain circumstances such as AIS-P/V
and STS/VT Unequipped. Service-Specific Payload formats reduce
bandwidth by suppressing transmission of portions of the SPE based
on specific knowledge of the SPE payload.
Details on these payload compression options are described in the
following subsections.
10.1 Dynamic Bandwidth Allocation
Dynamic Bandwidth Allocation (DBA) is an OPTIONAL mechanism for
suppressing the transmission of the SPE (or VT) fragment when one of
two trigger conditions are met, AIS-P/V or STS/VT Unequipped.
Implementations that support DBA MUST include a mechanism for
disabling DBA on a channel-by-channel basis to allow for
interoperability with implementations that do not support DBA.
When a DBA trigger is recognized at PW ingress, the CEP payload will
be suppressed. Padding bytes SHOULD be added if the intervening
packet network has a minimum packet size which is larger than the
payload-suppressed DBA packet.
Other than the suppression of the CEP payload, the CEP behavior
during DBA should be equivalent to normal CEP behavior. In
particular, the packet transmission rate during DBA should be
equivalent to the normal packet transmission rate.
10.2 Service-Specific Payload Formats
In addition to the standard payload encapsulations for SPE and VT
transport, several OPTIONAL payload formats have been defined to
provide varying amounts of payload compression depending on the type
and amount of user traffic present within the SPE. These are
described below.
pwe3-sonet Expires December 2003 [Page 27]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
10.2.1 Fractional STS-1 (VC-3) Encapsulation
Fractional STS-1 (VC-3) encapsulation carries only selected set of
VTs within an STS-1 container. This mode is applicable for STS-1
with POH signal label byte C2=2 (VT-structured SPE) and for C2=3
(Locked VT mode).
Implementations of fractional STS-1 (VC-3) encapsulation MUST
support payload length of one SPE and MAY support payload length of
1/3 SPE.
The mapping of VTs into an STS-1 container is described in section
3.2.4 of [GR253] and the mapping into VC-3 is defined in section
7.2.4 in [G.707]. The CEP packetizer removes all fixed column bytes
(columns 30 and 59) and all bytes that belong to the removed VTs.
Only STS-1 POH bytes and bytes that belong to the selected VTs are
carried within the payload. The CEP de-packetizer adds the fixed
stuff bytes and generates unequipped VT data replacing the removed
VT bytes. Figure 11 below describes VT mapping into an STS-1 SPE.
1 2 3 * * * 29 30 31 32 * * * 58 59 60 61 * * * 87
+--+------------------+-+------------------+-+------------------+
1 |J1| Byte 1 (V1-V4) |R| | | | |R| | | | |
+--+---+---+------+---+-+------------------+-+------------------+
2 |B3|VT | | | |R| | | | |R| | | | |
+--+1.5| | | +-+---+---+------+---+-+------------------+
3 |C2| | | | |R| | | | |R| | | | |
+--+ | | | +-+---+---+------+---+-+------------------+
4 |G1| | | | |R| | | | |R| | | | |
+--+ | | | +-+---+---+------+---+-+------------------+
5 |F2| | | | |R| | | | |R| | | | |
+--|1-1|2-1| * * *|7-4|-|1-1|2-1| * * *|7-4|-|1-1|2-1| * * *|7-4|
6 |H4| | | | |R| | | | |R| | | | |
+--+ | | | +-+---+---+------+---+-+------------------+
7 |Z3| | | | |R| | | | |R| | | | |
+--+ | | | +-+---+---+------+---+-+------------------+
8 |Z4| | | | |R| | | | |R| | | | |
+--+ | | | +-+---+---+------+---+-+------------------+
9 |Z5| | | | |R| | | | |R| | | | |
+--+---+---+------+---+-+---+---+------+---+-+------------------+
| | |
+-- Path Overhead +--------------------+-- Fixed Stuffs
Figure 11 - SONET SPE Mapping of VT1.5
The SPE always contains seven interleaved VT groups (VTGs). Each VTG
contains a single type of VT, and each VTG occupies 12 columns (108
bytes) within each SPE. A VTG can contain 4 VT1.5s (T1s), 3 VT2s
(E1s), 2 VT3s or a single VT6. Altogether, the SPE can carry 28 T1s
or carry 21 E1s.
pwe3-sonet Expires December 2003 [Page 28]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
The fractional STS-1 encapsulation can optionally carry a bit mask
that specifies which VTs are carried within the STS-1 payload and
which VTs have been removed. This optional bit mask attribute allows
the ingress circuit emulation node to remove an unequipped VT on the
fly, providing the egress circuit emulation node enough information
for reconstructing the VTs in the right order. The use of bit mask
enables on-the-fly compression, whereby only equipped VTs (carrying
actual data) are sent.
10.2.1.1 Fractional STS-1 CEP header
The fractional STS-1 CEP header uses the STS-1 CEP header
encapsulation as defined in this draft. Optionally, an additional 4
byte header extension word is added. The extended header is
described in Figure 12.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|R|D|N|P| Structure Pointer[0:12] | Sequence Number[0:13] |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|E|0|0|0| Equipped Bit Mask (EBM) [0:27] |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 12 - Extended Fractional STS-1 Header
The following fields are used within the extended header:
- R, D, N, P, Structured Pointer and Sequence Number: All
fields are used as defined in this draft for STS-1
encapsulation.
- E: Extension bit.
E=0: indicates that extended header is not used.
E=1: indicates that extended header is carried within the
packet.
The E bit in the first word is set to 1 to indicate use
of the Equipped Bit Mask (EBM). The E bit in the second
word indicates whether the extended header (to be defined
in future revision of this draft) is used.
- EBM: Each bit within the bit mask refers to a different VT
within the STS-1 container. A bit set to 1 indicates that
the corresponding VT is equipped, hence carried within the
fractional STS-1 payload.
pwe3-sonet Expires December 2003 [Page 29]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
The format of the EBM is defined in Figure 13.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| VTG7 | VTG6 | VTG5 | VTG4 | VTG3 | VTG2 | VTG1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 13 - Equipped Bit Mask (EBM) for fractional STS-1
The 28 bits of the EBM are divided into groups of 4 bits, each
corresponding to a different VTG within the STS container. All 4 bits
are used to indicate whether VT1.5 (T1) tributaries are carried
within a VTG. The first 3 bits read from right to left are used to
indicate whether VT2 (E1) tributaries are carried within a VTG. The
first two bits are used to indicate whether VT3 (DS1C) tributaries
are carried within a VTG and the right most bit is used to indicate
whether a VT6 (DS2) is carried within the VTG. The VTs within the VTG
are numbered from right to left, starting from the first VT as the
first bit on the right. For example, the EBM of a fully occupied STS-
1 with VT1.5 is all ones, while that of an STS-1 fully occupied with
VT2 (E1) tributaries has the binary value
0111011101110111011101110111.
10.2.1.2 B3 Compensation
Fractional STS-1 encapsulation can be implemented in Line
Terminating Equipment (LTE) or in Path Terminating Equipment (PTE).
PTE implementations terminate the path layer at the ingress PE and
generate a new path layer at the egress PE.
LTE implementations do not terminate the path layer, and therefore
need to keep the content and integrity of the POH bytes across the
PSN. In LTE implementations, special care must be taken to maintain
the B3 bit-wise parity POH byte. The B3 compensation algorithm is
defined below.
pwe3-sonet Expires December 2003 [Page 30]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Since the BIP-8 value in a given frame reflects the parity check
over the previous frame, the changes made to BIP-8 bits in the
previous frame shall also be considered in the compensation of BIP-8
in the current frame. Therefore the following equation shall be used
for compensation of the individual bits of the BIP-8:
B3[i]'(t) = B3[i](t-1) || B3[i]'(t-1) || B3[i](t) || B*3[i](t-1)
Where:
B3[i] = the existing B3[i] value in the incoming signal
B3[i]' = the new (compensated) B3[i] value.
B3*[i] = the B3[i] value of the unequipped VT(VC)s in the
incoming signal
|| = exclusive OR operator.
t = the time of the current frame.
t-1 = the time of the previous frame.
The egress PE MUST reconstruct the unequipped VTs and modify the B3
parity value in the same manner to accommodate for the additional VTs
added. In this way the end-to-end BIP is preserved.
10.2.1.3 Actual Payload Size
The actual CEP payload size depends on the number of virtual
tributaries carried within the fractional SPE. The contributions of
each tributary to the fractional STS-1 payload size as well as the
path overhead contribution are described below.
Each VT1.5 contributes 27 bytes
Each VT2 contributes 36 bytes
Each VT3 contributes 54 bytes
Each VT6 contributes 108 bytes
STS-1 POH contributes 9 bytes
For example, a fractional STS-1 carrying 7 VT2 circuit in full-SPE
encapsulation would have an actual size of 261=36*7+9 bytes. Divide
by 3 to calculate the third-SPE encapsulation actual payload sizes.
pwe3-sonet Expires December 2003 [Page 31]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
10.2.2 Asynchronous T3/E3 STS-1 (VC-3) Encapsulation
Asynchronous T3/E3 STS-1 (VC-3) encapsulation is applicable for STS-
1 with POH signal label byte C2=4, carrying asynchronous mapping of
T3 or E3 signals.
Implementations of asynchronous T3/E3 STS-1 (VC-3) encapsulation
MUST support payload length of one SPE and MAY support payload
length of 1/3 SPE.
10.2.2.1 T3 payload compression
A T3 is encapsulated asynchronously into an STS-1 SPE using the
format defined in section 3.4.2.1 of [GR253]. The STS-1 SPE is then
encapsulated as defined in this draft.
Optionally, the STS-1 SPE can be compressed by removing the fixed
columns leaving only data columns. STS-1 columns are numbered 1 to
87, starting from the POH column numbered 1. The following columns
have fixed values and are removed: 2, 3, 30, 31, 59, 60.
Bandwidth saving is approximately 7% (6 columns out of 87). The B3
parity byte need not be modified as the parity of the fixed columns
amounts to zero. The actual payload size for full-SPE encapsulation
would be 729 bytes and 243 bytes for third-SPE encapsulation.
A T3 is encapsulated asynchronously into a VC-3 container as
described in section 10.1.2.1 of [G.707]. VC-3 container has only 85
data columns, which is identical to the STS-1 container with the two
fixed stuff columns 30 and 59 removed. Other than that, the mapping
is identical.
10.2.2.2 E3 payload compression
An E3 is encapsulated asynchronously into a VC-3 SPE using the
format defined in section 10.1.2.2 of [G.707]. The VC-3 SPE is then
encapsulated as defined in this draft.
Optionally, the VC3 SPE can be compressed by removing the fixed
columns leaving only data columns. VC-3 columns are numbered 1 to 85
(and not 87), starting from the POH column numbered 1. The following
columns have fixed values and are removed: 2, 6, 10, 14, 18, 19, 23,
27, 31, 35, 39, 44, 48, 52, 56, 60, 61, 65, 69, 73, 77 and 81.
Bandwidth saving is approximately 28% (24 columns out of 85). The B3
parity byte need not be modified as the parity of the fixed columns
amounts to zero. The actual payload size for full-SPE encapsulation
would be 567 bytes and 189 bytes for third-SPE encapsulation.
pwe3-sonet Expires December 2003 [Page 32]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
10.2.3 Fractional VC-4 Encapsulation
SDH defines a mapping of VC-11, VC-12, VC-2 and VC-3 directly into
VC-4. This mapping does not have an equivalent within the SONET
hierarchy. The VC-4 mapping is common in SDH implementations.
VC-4 <--x3-- TUG-3 <--------x1-------- TU-3 <-- VC-3 <---- E3/T3
|
+--x7-- TUG-2 <--x1-- TU-2 <-- VC-2 <---- DS2
|
+----x3---- TU-12 <-- VC-12<---- E1
|
+----x4---- TU-11 <-- VC-11<---- T1
Figure 14 - Mapping of VCs into VC-4
Figure 14 describes the mapping options of VCs into VC-4. A VC-4
contains three TUG-3s. Each TUG-3 is composed of either a single TU-
3, or 7 TUG-2s. A TU-3 contains a single VC-3. A TUG-2 contains
either 4 VC-11s (T1s), 3 VC-12s (E1s) or one VC-2. Therefore a VC-4
may contain 3 VC-3s, 1 VC-3 and 42 VC-12s, 63 VC-12s, etc.
Fractional VC-4 encapsulation carries only selected set of VCs
within a VC-4 container. This mode is applicable for VC-4 with POH
signal label byte C2=2 (TUG structure) and for C2=3 (Locked TU-n).
The mapping of VCs into a VC-4 container is described in section 7.2
of [G.707]. The CEP packetizer removes all fixed column bytes and
all bytes that belong to the removed VCs. Only VC-4 POH bytes and
bytes that belong to the selected VCs are carried within the
payload. The CEP de-packetizer adds the fixed stuff bytes and
generates unequipped VC data replacing the removed VC bytes.
The fractional VC-4 encapsulation can optionally carry a bit mask
that specifies which VCs are carried within the VC-4 payload and
which VCs have been removed. This optional bit mask attribute allows
the ingress circuit emulation node to remove an unequipped VCs on the
fly, providing the egress circuit emulation node enough information
for reconstructing the VCs in the right order. The use of bit mask
enables on-the-fly compression, whereby only equipped VCs (carrying
actual data) are sent.
VC-3 carrying asynchronous T3/E3 signals within the VC-4 container
can optionally be compressed by removing the fixed column bytes as
described in section 10.2.2, providing additional bandwidth saving.
Implementations of fractional VC-4 encapsulation MUST support
payload length of 1/3 SPE and MAY support payload lengths of 4/9,
5/9, 6/9, 7/9, 8/9 and full SPE. The actual payload size of
fractional VC-4 encapsulation depends on the number of VCs carried
within the payload.
pwe3-sonet Expires December 2003 [Page 33]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
10.2.3.1 Fractional VC-4 Mapping
[G.707] defines the mapping of TUG-3 to a VC-4 in section 7.2.1. Each
TUG-3 includes 86 columns. TUG-3#1, TUG-3#2 and TUG-3#3 are byte
multiplexed, starting from column 4. Column 1 is the VC-4 POH, while
columns 2 and 3 are fixed, and therefore removed within the
fractional VC-4 encapsulation.
The mapping of TU-3 into TUG-3 is defined in section 7.2.2 of
[G.707]. The TU-3 consists of the VC-3 with a 9-byte VC-3 POH and
the TU-3 pointer. The first column of the 9-row by 86-column TUG-3
is allocated to the TU-3 pointer (bytes H1, H2, H3) and fixed stuff.
The phase of the VC-3 with respect to the TUG-3 is indicated by the
TU-3 pointer.
The mapping of TUG-2 into TUG-3 is defined in section 7.2.3 of
[G707]. The first two columns of the TUG-3 are fixed and therefore
removed in the fractional VC-4 encapsulation. The 7 TUG-2, each 12
columns wide, are byte multiplexed starting from column 3 of the TUG-
3. This is the equivalent of multiplexing 7 VTGs within STS-1
container in SONET terminology, except for the location of the fixed
columns.
The static fractional VC-4 mapping assumes that both the ingress and
egress nodes are preconfigured with the set of equipped VCs carried
within the fractional VC-4 encapsulation. The ingress emulation edge
removes the fixed columns as well as columns of the VCs agreed upon
by the two edges, and updates the B3 VC-4 byte. The egress side adds
the fixed columns and the unequipped VCs and updates B3.
10.2.3.2 Fractional VC-4 CEP Header
The fractional VC-4 CEP header uses the VC-4 CEP header defined
Section 3.3 in this draft. Optionally, an additional 12 byte header
extension word is added. The extended header is described in Figure
15.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|R|D|N|P| Structure Pointer[0:12] | Sequence Number[0:13] |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| Equipped Bit Mask #1 (EBM) [0:29] TUG-3#1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| Equipped Bit Mask #2 (EBM) [0:29] TUG-3#2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|E|0| Equipped Bit Mask #3 (EBM) [0:29] TUG-3#3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 15 - Extended Fractional VC-4 Header
pwe3-sonet Expires December 2003 [Page 34]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
The following fields are used within the extended header:
- R, D, N, P, Structured Pointer and Sequence Number: All
fields are used as defined in this draft for VC-4
encapsulation.
- E: Extension bit.
E=0: indicates that extended header is not used.
E=1: indicates that extended header is carried within the
packet.
The E bit in the first word is set to 1 to indicate use
of the Equipped Bit Mask (EBM). The E bit in the forth
word indicates whether the extended header (to be defined
in future revision of this draft) is used. The MSB bits of
second and third words are always set to 1 to indicate that
header is extended.
- EBM: The Equipped Bit Mask indicate which tributaries are
carried within the fractional VC-4 payload.
Three EBM fields are used. Each EBM field corresponds to a different
TUG-3 within the VC-4. The EBM includes 7 groups of 4 bits per TUG-2.
A bit set to 1 indicates that the corresponding VC is equipped, hence
carried within the fractional VC-4 payload. Additional 2 bit within
the EBM indicates whether VC-3 carried within the TUG-3 is equipped
and whether it is in AIS mode.
The format of the EBM for fractional VC-4 is defined corresponding to
one of the TUG-3 is defined in Figure 16.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|A|T|TUG2#7 |TUG2#6 |TUG2#5 |TUG2#4 |TUG2#3 |TUG2#2 |TUG2#1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 16 - Equipped Bit Mask (EBM) for fractional VC-4
The 30 bits of the EBM are divided into two bits that control the VC-
3 within the TUG-3 and 7 groups of 4 bits, each corresponding to a
different TUG-2 within the TUG-3 container.
For a TUG-3 containing TUG-2, the first two A and T bits MUST be set
to zero. The TUG-2 bits indicate whether the VCs within the TUG-2 are
equipped. All 4 bits are used to indicate whether VC11 (T1)
tributaries are carried within a TUG-2. The first 3 bits read right
to left are used to indicate whether VC12 (E1) tributaries are
carried within a TUG-2. The first bit is used to indicate a VC-2 is
carried within a TUG-2. The VCs within the VUG-2 are numbered from
right to left, starting from the first VC as the first bit on the
pwe3-sonet Expires December 2003 [Page 35]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
right. For example, 28 bits of the EBM of a fully occupied TUG-3 with
VC11 is all ones, while that of a TUG-3 fully occupied with VC12 (E1)
tributaries has the binary value 000111011101110111011101110111.
For a TUG-3 containing VC-3, all TUG-2 bits MUST be set to zero. The
A and T bits are defined as follows:
T: TUG-3 carried bit. If set to 1, the VC-3 payload is carried within
the TUG-3 container. If set to 0, all the TUG-3 columns are not
carried within the fractional VC-4 encapsulation. The TUG-3 columns
are removed either because the VC-3 is unequipped or in AIS mode.
A: VC-3 AIS bit. The A bit MUST be set to 0 when the T bit is 1 (i.e.
when the TUG-3 columns are carried within the fractional VC-4
encapsulation). The A bit indicate the reason for removal of the
entire TUG-3 columns. If set to 0, the TUG-3 columns were removed
because the VC-3 is unequipped. If set to 1, the TUG-3 columns were
removed because the VC-3 is in AIS mode.
10.2.3.3 B3 Compensation
Fractional VC-4 encapsulation can be implemented in Line Terminating
Equipment (LTE) or in Path Terminating Equipment (PTE). PTE
implementations terminate the path layer at the ingress PE and
generate a new path layer at the egress PE. LTE implementations do
not terminate the path layer, and therefore need to keep the content
and integrity of the POH bytes across the PSN. In LTE
implementations, special care must be taken to maintain the B3 bit-
wise parity POH byte. The same procedures for B3 compensation as
described in section 7.2.1.2 for fractional STS-1 encapsulation are
used.
10.2.3.4 Actual Payload Sizes
The actual CEP payload size depends on the number of virtual
tributaries carried within the fractional SPE. The contributions of
each tributary to the fractional VC-4 payload length as well as the
path overhead contribution are described below.
Each VC-11 contributes 27 bytes
Each VC-12 contributes 36 bytes
Each VC-2 contributes 108 bytes
Each VC-3(T3) contributes 738 bytes
Each VC-3(E3) contributes 576 bytes
Each VC-3(uncompressed) contributes 774 bytes
VC-4 POH contributes 9 bytes
The VC-3 contribution includes the AU-3 pointer. For example, the
payload size of a fractional VC-4 configured to third-SPE
encapsulation that carries a single compressed T3 VC-3 and 6 VC-12s
would be: 321=(9 + 6*36 + 738) / 3 bytes payload per each packet.
pwe3-sonet Expires December 2003 [Page 36]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
11 Signaling of CEP Pseudo Wires
[PWE3-CONTROL] specifies the use of the MPLS Label Distribution
Protocol, LDP, as a protocol for setting up and maintaining pseudo
wires. It enables LDP to identify pseudo-wires and to signal
attributes of pseudo-wires. In particular it provides a way to bind
a de-multiplexer field value to a pseudo-wire, specifies procedures
for reporting pseudo-wire status changes and for releasing the
bindings. [PWE3-CONTROL] assumes the pseudo-wire de-multiplexer
field is an MPLS label; however the PSN tunnel itself can be either
an IP or MPLS PSN.
The use of LDP for setting up and maintaining CEP pseudo-wires is
OPTIONAL. This section describes the use of the CEP-specific fields
and error codes.
The PW Type field in PWid FEC and PW generalized ID FEC elements
MUST be set to SONET/SDH Circuit Emulation over Packet (CEP)[IANA].
The control word is REQUIRED for CEP pseudo-wires. Therefore the
C-bit in PWid FEC and PW generalized ID FEC elements MUST be set. If
the C-bit is not set the pseudo-wire MUST not be established and a
Label Release MUST be sent with an Illegal C-bit status code [IANA].
The PWid FEC and PW generalized ID FEC elements can include one or
more Interface Parameters fields. The Interface Parameters fields
are used to validate that the two ends of the pseudo-wire have the
necessary capabilities to interoperate with each other. The CEP
specific Interface Parameters fields are the CEP/TDM Payload Bytes,
the CEP Option and the CEP/TDM Bit Rate parameters.
11.1 CEP/TDM Payload Bytes
This parameter MUST contain the expected CEP payload size in bytes.
The payload size does not include network headers, control word or
padding. If payload compression is used, the CEP/TDM Payload Bytes
parameter MUST be set to the uncompressed payload size as if payload
compression was disabled. In particular, when Fractional SPE (STS-
1/VC-3 or VC-4) payload compression is used, the payload bytes
parameter MUST be set to the payload size before removal of the
unequipped VT containers and fixed value columns. Therefore, when
fractional SPE mode is used, the actual (i.e. on the wire) packet
length would normally be less than advertised, and in dynamic
fractional SPE, even change while the connection is active.
Similarly when DBA payload compression is used, the CEP/TDM Payload
Bytes parameter MUST be set to the payload size prior to
compression.
The CEP/TDM Payload Bytes parameter is OPTIONAL. Default payload
sizes are assumed if this parameter is not included as part of the
Interface Parameters fields. The default payload size for VT is a
single super frame. The default payload size for SPE is 783 bytes.
pwe3-sonet Expires December 2003 [Page 37]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
A PE that receives a label-mapping message with request for a
CEP/TDM Payload Bytes value that is not locally supported MUST
return CEP/TDM mis-configuration status error code [IANA] and the
pseudo wire MUST not be established.
11.2 CEP/TDM Bit Rate
The CEP/TDM Bit Rate parameter MUST be set to the data rate in
64Kbps units of the CEP payload. If payload compression is used, the
CEP/TDM Bit Rate parameter MUST be set to the uncompressed payload
data rate as if payload compression was disabled. Table 3 specifies
the CEP/TDM Bit Rate parameters that MUST be set for each of the
pseudo-wire circuits.
+-----------------+---------------------------+
| Circuit | Bit Rate Parameter |
+-----------------+---------------------------+
| VT1.5/VC-11 | 26 |
| VT2/VC-12 | 35 |
| VT3 | 53 |
| VT6/VC-2 | 107 |
| STS-Nc | 783*N N=1,3,12,48,192 |
+-----------------+---------------------------+
Table 3 - CEP/TDM Bit Rates
The CEP/TDM Bit Rate parameter is MANDATORY. Attempts to establish a
pseudo-wire between two peers with different bit-rates MUST be
rejected with incompatible bit rate status error code [IANA] and
the pseudo wire MUST not be established.
11.3 CEP Options
The CEP Options parameter is MANDATORY. The format of the CEP
Options parameter is shown in Figure 17.
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
|AIS|UNE|RTP|EBM|MAH| RESERVED [0:5] | CEP Type | Async |
| | | | | | | [0:2] |T3 |E3 |
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
Figure 17 - CEP Options
AIS - When set, indicates that the PE sending the label-mapping
message is able to accept DBA packets with AIS indication.
pwe3-sonet Expires December 2003 [Page 38]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
UNE - When set, indicates that the PE sending the label-mapping
message is able to accept DBA packets with unequipped indication.
RTP - When set, indicates that RTP header is required.
EBM - When set, indicates that EBM header is required.
MAH - When set, indicates that CEP MPLS Adaptation Header is
required.
CEP Type - indicates the CEP connection type:
0x0 SPE mode (STS-1/STS-Mc)
0x1 VT mode (VT1.5/VT2/VT3/VT6)
0x2 Fractional SPE (STS-1/VC-3/VC-4)
Async Type - indicates the Async E3/T3 bandwidth reduction
capabilities. Relevant only when CEP type is set to fractional SPE,
and fractional SPE is expected to carry Asynchronous T3/E3
payload:
T3 - When set, indicates that the PE sending the label-mapping
message is able to accept Fractional SPE packets with T3 bandwidth
reduction.
E3 - When set, indicates that the PE sending the label-mapping
message is able to accept Fractional SPE packets with E3 bandwidth
reduction.
A PE that does not support the DBA option or one of the DBA sub
option, can simply ignore label-mapping messages with either AIS or
UNE bits set, and no further protocol action is required. A PE that
is configured to use one of the DBA options but receives a label-
mapping message indicating that its peer cannot process DBA packets
MUST not use the DBA option, and SHOULD report the mismatch to the
operator.
A PE that does not support the Async bandwidth reduction mode can
simply ignore label-mapping messages with either T3 or E-3 bits
set, and no further protocol action is required. A PE that is
configured to use one of the Async options but receives a label-
mapping message indicating that its peer cannot process Async
bandwidth reduction T3/E3 payloads MUST not use the Async option,
and SHOULD report the mismatch to the operator.
The setting of the CEP type, RTP, EBM and MAH bits MUST be
consistent between peers. If a peer receives a label-mapping message
with inconsistent setting compared with the local configuration, it
should send a label-withdraw message with status code of CEP/TDM
mis-configuration [IANA], report to the operator and wait for a new
(consistent) label mapping. A PE MUST send a new label-mapping
message once it is re-configured.
pwe3-sonet Expires December 2003 [Page 39]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
12 Security Considerations
The CEP encapsulation is subject to all of the general security
considerations discussed in [PWE3-ARCH]. In addition, this document
specifies only encapsulations, and not the protocols used to carry
the encapsulated packets across the PSN. Each such protocol may
have its own set of security issues, but those issues are not
affected by the encapsulations specified herein. Note that the
security of the transported CEP service will only be as good as the
security of the PSN. This level of security may be less rigorous
then that available from a native TDM service due to the inherent
differences between circuit-switched and packet-switched public
networks.
13 Intellectual Property Disclaimer
This document is being submitted for use in IETF standards
discussions. Tellabs, Inc. and Lycium Networks, Inc. have filed one
or more patent applications relating to the CEP technology described
in this document. In the event that Tellabs, Inc is granted a patent
or patents essential to the implementation of this document,
Tellabs, Inc. agrees to grant a free unlimited license to all
parties implementing the document, subject to reciprocity of the
licensed party.
In the event that Lycium Network, Inc is granted a patent or patents
essential to the implementation of this document, Lycium Networks,
Inc. agrees to grant a free unlimited license to all parties
implementing the document, subject to reciprocity of the licensed
party.
Level3 Communications, LLC. has filed one or more patent
applications relating to the technology outlined in this document.
14 References
Normative References
[RFC2026] Bradner, S., The Internet Standards Process - Revision 3,
BCP 9, RFC2026, October 1996.
[RFC2119] Bradner, S., Key words for use in RFCs to Indicate
Requirement Levels, BCP 14, RFC 2119, March 1997.
[PWE3-REQ] XiPeng Xiao et al, Requirements for Pseudo Wire Emulation
Edge-to-Edge (PWE3), Work in Progress, December 2003, draft-ietf-
pwe3-requirements-08.txt
pwe3-sonet Expires December 2003 [Page 40]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
[PWE3-TDM-REQ] Max Riegel, Requirements for Edge-to-Edge Emulation
of TDM Circuits over Packet Switching Networks (PSN), Work in
Progress, January 2004, draft-ietf-pwe3-tdm-requirements-04.txt.
[PWE3-ARCH] Stewart Bryant and Prayson Pate, PWE3 Architecture, Work
in progress, March 2004, draft-ietf-pwe3-arch-07.txt
[PWE3-CONTROL] Martini et al, Pseudo-wire Setup and Maintenance
using LDP, work in progress, March 2004, draft-ietf-pwe3-control-
protocol-06.txt.
[SONET] American National Standards Institute, Synchronous Optical
Network (SONET) - Basic Description including Multiplex Structure,
Rates and Formats, ANSI T1.105-1995.
[GR253] Telcordia Technologies, Synchronous Optical Network (SONET)
Transport Systems: Common Generic Criteria, GR-253-CORE, Issue 3,
September 2000.
[G707] ITU Recommendation G.707, Network Node Interface For The
Synchronous Digital Hierarchy, 1996.
[RFC1889] H. Schulzrinne et al, RTP: A Transport Protocol for Real-
Time Applications, RFC 1889, IETF, 1996
Informative References
[CEP-MIB] Danenberg et al, SONET/SDH Circuit Emulation Service Over
PSN (CEP) Management Information Base Using SMIv2,draft-ietf-pwe3-
cep-mib-04.txt, work in progress, December 2003.
[RFC2508] S.Casner, V.Jacobson, Compressing IP/UDP/RTP Headers for
Low-Speed Serial Links, RFC 2508, IETF, 1999
[RFC3095] C.Bormann (Ed.), RObust Header Compression (ROHC):
Framework and four profiles: RTP, UDP, ESP, and uncompressed, RFC
3095, IETF, 2001
[AAL1] ITU-T, Recommendation I.363.1, B-ISDN Adaptation Layer
Specification: Type AAL1, Appendix III, August 1996.
[L2TPv3] Layer Two Tunneling Protocol (Version 3) 'L2TPv3', J Lau,
et. al., work in progress, March 2004, draft-ietf-l2tpext-l2tp-base-
12.txt.
[IANA] Luca Martini and Mark Townsley, IANA Allocations for pseudo
Wire Edge to Edge Emulation (PWE3), Work in Progress, March 2004,
draft-ietf-pwe3-iana-allocation-03.txt.
pwe3-sonet Expires December 2003 [Page 41]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
15 Author's Addresses
Andrew G. Malis
Tellabs, Inc.
2730 Orchard Parkway
San Jose, CA 95134
Email: Andy.Malis@tellabs.com
Ken Hsu
Tellabs, Inc.
2730 Orchard Parkway
San Jose, CA 95134
Email: Ken.Hsu@tellabs.com
Jeremy Brayley
Laurel Networks, Inc.
Omega Corporate Center
1300 Omega Drive
Pittsburgh, PA 15205
Email: jbrayley@laurelnetworks.com
Steve Vogelsang
Laurel Networks, Inc.
Omega Corporate Center
1300 Omega Drive
Pittsburgh, PA 15205
Email: sjv@laurelnetworks.com
John Shirron
Laurel Networks, Inc.
Omega Corporate Center
1300 Omega Drive
Pittsburgh, PA 15205
Email: jshirron@laurelnetworks.com
Luca Martini
Cisco Systems, Inc.
9155 East Nichols Avenue, Suite 400
Englewood, CO, 80112
Email: lmartini@cisco.com
Tom Johnson
Litchfield Communications, Inc.
Ed Hallman
Litchfield Communications, Inc.
Marlene Drost
Litchfield Communications, Inc.
pwe3-sonet Expires December 2003 [Page 42]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Jim Boyle
Juniper Networks, Inc.
1194 N. Mathilda Ave
Sunnyvale, CA 94089
David Zelig
Corrigent Systems
126, Yigal Alon st.
Tel Aviv, ISRAEL
Email: davidz@corrigent.com
Ron Cohen
Lycium Networks, Inc.
2480 Sand Hill Road, suite 200
Menlo-Park, CA, 94025
Email: ronc@lyciumnetworks.com
Prayson Pate
Overture Networks, Inc.
507 Airport Blvd, Suite 111
Morrisville, NC, USA 27560
Email: prayson.pate@overturenetworks.com
Craig White
Level3 Communications, LLC.
1025 Eldorado Blvd,
Broomfield CO 80021
Email: Craig.White@Level3.com
pwe3-sonet Expires December 2003 [Page 43]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Appendix A. SONET/SDH Rates and Formats
For simplicity, the discussion in this section uses SONET
terminology, but it applies equally to SDH as well. SDH-equivalent
terminology is shown in the tables.
The basic SONET modular signal is the synchronous transport signal-
level 1 (STS-1). A number of STS-1s may be multiplexed into higher-
level signals denoted as STS-N, with N synchronous payload envelopes
(SPEs). The optical counterpart of the STS-N is the Optical Carrier-
level N, or OC-N. Table 4 lists standard SONET line rates discussed
in this document.
OC Level OC-1 OC-3 OC-12 OC-48 OC-192
SDH Term - STM-1 STM-4 STM-16 STM-64
Line Rate(Mb/s) 51.840 155.520 622.080 2,488.320 9,953.280
Table 4 - Standard SONET Line Rates
Each SONET frame is 125us and consists of nine rows. An STS-N frame
has nine rows and N*90 columns. Of the N*90 columns, the first N*3
columns are transport overhead and the other N*87 columns are SPEs.
A number of STS-1s may also be linked together to form a super-rate
signal with only one SPE. The optical super-rate signal is denoted
as OC-Nc, which has a higher payload capacity than OC-N.
The first 9-byte column of each SPE is the path overhead (POH) and
the remaining columns form the payload capacity with fixed stuff
(STS-Nc only). The fixed stuff, which is purely overhead, is N/3-1
columns for STS-Nc. Thus, STS-1 and STS-3c do not have any fixed
stuff, STS-12c has three columns of fixed stuff, and so on.
The POH of an STS-1 or STS-Nc is always nine bytes in nine rows. The
payload capacity of an STS-1 is 86 columns (774 bytes) per frame.
The payload capacity of an STS-Nc is (N*87)-(N/3) columns per frame.
Thus, the payload capacity of an STS-3c is (3*87 - 1)*9 = 2,340
bytes per frame. As another example, the payload capacity of an STS-
192c is 149,760 bytes, which is 64 times the capacity of an STS-3c.
There are 8,000 SONET frames per second. Therefore, the SPE size,
(POH plus payload capacity) of an STS-1 is 783*8*8,000 = 50.112
Mb/s. The SPE size of a concatenated STS-3c is 2,349 bytes per frame
or 150.336 Mb/s. The payload capacity of an STS-192c is 149,760
bytes per frame, which is equivalent to 9,584.640 Mb/s. Table 5
lists the SPE and payload rates supported.
pwe3-sonet Expires December 2003 [Page 44]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
SONET STS Level STS-1 STS-3c STS-12c STS-48c STS-192c
SDH VC Level - VC-4 VC-4-4c VC-4-16c VC-4-64c
Payload Size(Bytes) 774 2,340 9,360 37,440 149,760
Payload Rate(Mb/s) 49.536 149.760 599.040 2,396.160 9,584.640
SPE Size(Bytes) 783 2,349 9,396 37,584 150,336
SPE Rate(Mb/s) 50.112 150.336 601.344 2,405.376 9,621.504
Table 5 - Payload Size and Rate
To support circuit emulation, the entire SPE of a SONET STS or SDH
VC level is encapsulated into packets, using the encapsulation
defined in section 4, for carriage across packet-switched networks.
VTs are organized in SONET super-frames, where a SONET super-frame
is a sequence of four SONET SPEs. The SPE path overhead byte H4
indicates the SPE number within the super-frame. The VT data can
float relative to the SPE position. The overhead bytes V1, V2 and
V3 are used as pointer and stuffing byte similar to the use of the
H1, H2 and H3 TOH bytes.
pwe3-sonet Expires December 2003 [Page 45]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Appendix B: Example Network Diagrams
Figure 18 below illustrates a SONET interconnect example. Site A
and Site B are connected back to a Hub Site, Site C by means of a
SONET infrastructure. The OC3 from Site A and the OC12 from Site B
are partially equipped. Each of them is transported through a SONET
network back to a hub site (C). Equipped SPEs (or VTs) are then
groomed onto the OC-12 towards site C.
SONET Network
____ ___ ____
_/ \___/ \ _/ \__
+------+ Physical / \__/ \
|Site A| OC-12 / +---+ OC-12 \ Hub Site
| |=================|\S/|-------------+-----+ \ +------+
| | \ |/ \|=============|\ /| \ | |
+------+ /\ +---+-------------| \ / | / OC12 | |
/ | S |=========|Site C|
+------+ Physical/ +---+-------------| / \ | \ | |
|Site B| OC-12 \ |\S/|=============|/ \| \ | |
| |=================|/ \|-------------+-----+ / +------+
| | \ +---+ OC12 __ /
+------+ \ __/ \ /
\ ___ ___ / \_/
\_/ \____/ \___/
Figure 18 - SONET Interconnect Example Diagram
pwe3-sonet Expires December 2003 [Page 46]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Figure 19 below illustrates the same pair of OC12s being emulated
over a PSN. This configuration frees up bandwidth in the grooming
network, since only equipped SPEs (or VTs) are sent through the PSN.
Additional bandwidth savings can be realized by taking advantage of
the various payload compression options described in section 10. .0.
SONET/TDM/Packet Network
____ ___ ____
/ \___/ \ / \__
+------+ Physical /+-+ \__/ \_
|Site A| OC12 / | | +---+ \ Hub Site
| |=============|P|=| R | +---+ +-+ +-----+ \ +------+
| | \ |E| | |===| | | |=|\ /| \ | |
+------+ /\+-+ +---+ | | | | | \ / | / OC12| |
/ | R |=|P| | S |========|Site C|
+------+ Physical/ +-+ +---+ | | |E| | / \ | \ | |
|Site B| OC12 \ |P| | R |===| | | |=|/ \| \ | |
| |=============|E|=| | +---+ +-+ +-----+ / +------+
| | \ | | +---+ __ /
+------+ \ +-+ __/ \ /
\ ___ ___ / \_/
\_/ \____/ \___/
Figure 19 - SONET Interconnect Emulation Example Diagram
Figure 20 below shows an example of T1 grooming into OC-12 in access
networks. The VT encapsulation is used to transport the T1s from the
Hub site to customer sites, maintaining SONET/SDH OA&M.
SONET/TDM/Packet Network
____ ___ ____
_/ \___/ \ _/ \__
+------+ Physical /+-+ \__/ \_
|Site A| T1 / | | +---+ \ Hub Site
| |=============|P|=| R | +---+ +-+ +-----+ \ +------+
| | \ |E| | |===| | | |=|\ /| \ | |
+------+ /\+-+ +---+ | | | | | \ / | / OC12| |
/ | R |=|P| | S |========|Site C|
+------+ Physical/ +-+ +---+ | | |E| | / \ | \ | |
|Site B| T1 \ |P| | R |===| | | |=|/ \| \ | |
| |=============|E|=| | +---+ +-+ +-----+ / +------+
| | \ | | +---+ __ /
+------+ \ +-+ __/ \ /
\ ___ ___ / \_/
\_/ \____/ \___/
Figure 20 - T1 to OC-12 Grooming Emulation Example Diagram
pwe3-sonet Expires December 2003 [Page 47]
Internet Draft draft-ietf-pwe3-sonet-05 April 2004
Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved. This
document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
AS IS basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
We thank Sasha Vainshtein for his valuable feedback.
pwe3-sonet Expires December 2003 [Page 48]