Network Working Group Z. Sarker
Internet-Draft I. Johansson
Intended status: Informational Ericsson AB
Expires: December 13, 2015 June 11, 2015
Evaluation Test Cases for Interactive Real-Time Media over Wireless
Networks
draft-ietf-rmcat-wireless-tests-00
Abstract
It is evident that to ensure seamless and robust user experience
across all type of access networks multimedia communication suits
should adapt to the changing network conditions. There is an ongoing
effort in IETF RMCAT working group to standardize rate adaptive
algorithm(s) to be used in the real-time interactive communication.
In this document test cases are described to evaluate the
performances of the proposed endpoint adaptation solutions in LTE
networks and Wi-Fi networks. It is aimed that the proposed solutions
should be evaluated using the test cases defined in this document to
select most optimal solutions.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 13, 2015.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Sarker & Johansson Expires December 13, 2015 [Page 1]
Internet-Draft RMCAT Wireless Test Cases June 2015
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminologies . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Cellular Network Specific Test Cases . . . . . . . . . . . . 3
3.1. Varying Network Load . . . . . . . . . . . . . . . . . . 5
3.1.1. Network Connection . . . . . . . . . . . . . . . . . 6
3.1.2. Simulation Setup . . . . . . . . . . . . . . . . . . 6
3.2. Bad Radio Coverage . . . . . . . . . . . . . . . . . . . 8
3.2.1. Network connection . . . . . . . . . . . . . . . . . 8
3.2.2. Simulation Setup . . . . . . . . . . . . . . . . . . 8
3.3. Desired Evaluation Metrics for cellular test cases . . . 9
4. Wi-Fi Networks Specific Test Cases . . . . . . . . . . . . . 9
5. Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . 10
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 10
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
8. Security Considerations . . . . . . . . . . . . . . . . . . . 10
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 10
9.1. Normative References . . . . . . . . . . . . . . . . . . 10
9.2. Informative References . . . . . . . . . . . . . . . . . 11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 11
1. Introduction
Wireless networks (both cellular and Wi-Fi [IEEE802.11] local area
network) are an integral part of the Internet. Mobile devices
connected to the wireless networks produces huge amount of media
traffic in the Internet. They covers the scenarios of having a video
call in the bus to media consumption sitting on a couch in a living
room. It is a well known fact that the characteristic and challenges
for offering service over wireless network are very different than
providing the same over a wired network. Even though RMCAT basic
test cases defines number of test cases that covers lots of effects
of the impairments visible in the wireless networks but there are
characteristics and dynamics those are unique to particular wireless
environment. For example, in the LTE the base station maintains
queues per radio bearer per user hence it gives different interaction
when all traffic from user share the same queue. Again, the user
mobility in a cellular network is different than the user mobility in
a Wi-Fi network. Thus, It is important to evaluate the performance
Sarker & Johansson Expires December 13, 2015 [Page 2]
Internet-Draft RMCAT Wireless Test Cases June 2015
of the proposed RMCAT candidates separately in the cellular mobile
networks and Wi-Fi local networks (IEEE 802.11xx protocol family ).
RMCAT evaluation criteria [I-D.ietf-rmcat-eval-criteria] document
provides the guideline to perform the evaluation on candidate
algorithms and recognizes wireless networks to be important access
link. However, it does not provides particular test cases to
evaluate the performance of the candidate algorithm. In this
document we device test cases specifically targeting cellular
networks such as LTE networks and Wi-Fi local networks.
2. Terminologies
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [RFC2119]
3. Cellular Network Specific Test Cases
A cellular environment is more complicated than a wireline ditto
since it seeks to provide services in the context of variable
available bandwidth, location dependencies and user mobilities at
different speeds. In a cellular network the user may reach the cell
edge which may lead to a significant amount of retransmissions to
deliver the data from the base station to the destination and vice
versa. These network links or radio links will often act as a
bottleneck for the rest of the network which will eventually lead to
excessive delays or packet drops. An efficient retransmission or
link adaptation mechanism can reduce the packet loss probability but
there will still be some packet losses and delay variations.
Moreover, with increased cell load or handover to a congested cell,
congestion in transport network will become even worse. Besides,
there are certain characteristics which make the cellular network
different and challenging than other types of access network such as
Wi-Fi and wired network. In a cellular network -
o The bottleneck is often a shared link with relatively few users.
* The cost per bit over the shared link varies over time and is
different for different users.
* Left over/ unused resource can be grabbed by other greedy
users.
o Queues are always per radio bearer hence each user can have many
of such queues.
Sarker & Johansson Expires December 13, 2015 [Page 3]
Internet-Draft RMCAT Wireless Test Cases June 2015
o Users can experience both Inter and Intra Radio Access Technology
(RAT) handovers ("handover" definition in [HO-def-3GPP] ).
o Handover between cells, or change of serving cells (see in
[HO-LTE-3GPP] and [HO-UMTS-3GPP] ) might cause user plane
interruptions which can lead to bursts of packet losses, delay
and/or jitter. The exact behavior depends on the type of radio
bearer. Typically, the default best effort bearers do not
generate packet loss, instead packets are queued up and
transmitted once the handover is completed.
o The network part decides how much the user can transmit.
o The cellular network has variable link capacity per user
* Can vary as fast as a period of milliseconds.
* Depends on lots of facts (such as distance, speed,
interference, different flows).
* Uses complex and smart link adaptation which makes the link
behavior ever more dynamic.
* The scheduling priority depends on the estimated throughput.
o Both Quality of Service (QoS) and non-QoS radio bearers can be
used.
Hence, a real-time communication application operating in such a
cellular network need to cope with shared bottleneck link and
variable link capacity, event likes handover, non-congestion related
loss, abrupt change in bandwidth (both short term and long term) due
to handover, network load and bad radio coverage. Even though 3GPP
define QoS bearers [QoS-3GPP] to ensure high quality user experience,
adaptive real-time applications are desired.
Different mobile operators deploy their own cellular network with
their own set of network functionalities and policies. Usually, a
mobile operator network includes 2G, EDGE, 3G and 4G radio access
technologies. Looking at the specifications of such radio
technologies it is evident that only 3G and 4G radio technologies can
support the high bandwidth requirements from real-time interactive
video applications. The future real-time interactive application
will impose even greater demand on cellular network performance which
makes 4G (and beyond radio technologies) more suitable access
technology for such genre of application.
The key factors to define test cases for cellular network are
Sarker & Johansson Expires December 13, 2015 [Page 4]
Internet-Draft RMCAT Wireless Test Cases June 2015
o Shared and varying link capacity
o Mobility
o Handover
However, for cellular network it is very hard to separate such events
from one another as these events are heavily related. Hence instead
of devising separate test cases for all those important events we
have divided the test case in two categories. It should be noted
that in the following test cases the goal is to evaluate the
performance of candidate algorithms over radio interface of the
cellular network. Hence it is assumed that the radio interface is
the bottleneck link between the communicating peers and that the core
network does not add any extra congestion in the path. Also the
combination of multiple access technologies such as one user has LTE
connection and another has Wi-Fi connection is kept out of the scope
of this document. However, later those additional scenarios can also
be added in this list of test cases. While defining the test cases
we assumed a typical real-time telephony scenario over cellular
networks where one real-time session consists of one voice stream and
one video stream. We recommend that an LTE network simulator is used
for the test cases defined in this document, for example-NS-3 LTE
simulator [LTE-simulator].
3.1. Varying Network Load
The goal of this test is to evaluate the performance of the candidate
congestion control algorithm under varying network load. The network
load variation is created by adding and removing network users a.k.a.
User Equipments (UEs) during the simulation. In this test case, each
of the user/UE in the media session is an RMCAT compliant endpoint.
The arrival of users follows a Poisson distribution, which is
proportional to the length of the call, so that the number of users
per cell is kept fairly constant during the evaluation period. At
the beginning of the simulation there should be enough amount of time
to warm-up the network. This is to avoid running the evaluation in
an empty network where network nodes are having empty buffers, low
interference at the beginning of the simulation. This network
initialization period is therefore excluded from the evaluation
period.
This test case also includes user mobility and competing traffic.
The competing traffics includes both same kind of flows (with same
adaptation algorithms) and different kind of flows (with different
service and congestion control). The investigated congestion control
algorithms should show maximum possible network utilization and
stability in terms of rate variations, lowest possible end to end
Sarker & Johansson Expires December 13, 2015 [Page 5]
Internet-Draft RMCAT Wireless Test Cases June 2015
frame latency, network latency and Packet Loss Rate (PLR) at
different cell load level.
3.1.1. Network Connection
Each mobile user is connected to a fixed user. The connection
between the mobile user and fixed user consists of a LTE radio
access, an Evolved Packet Core (EPC) and an Internet connection. The
mobile user is connected to the EPC using LTE radio access technology
which is further connected to the Internet. The fixed user is
connected to the Internet via wired connection with no bottleneck
(practically infinite bandwidth). The Internet and wired connection
in this setup does not add any network impairments to the test, it
only adds 10ms of one-way transport propagation delay.
The path from the fixed user to mobile user is defines as "Downlink"
and the path from mobile user to the fixed user is defined as
"Uplink". We assume that only uplink or downlink is congested for
the mobile users. Hence, we recommend that the uplink and downlink
simulations are run separately.
uplink
++))) +-------------------------->
++-+ ((o))
| | / \ +-------+ +------+ +---+
+--+ / \----+ +-----+ +----+ |
/ \ +-------+ +------+ +---+
UE BS EPC Internet fixed
<--------------------------+
downlink
Figure 1: Simulation Topology
3.1.2. Simulation Setup
The values enclosed within " [ ] " for the following simulation
attributes follow the notion set in [I-D.ietf-rmcat-eval-test]. The
desired simulation setup as follows-
1. Radio environment
A. Deployment and propagation model : 3GPP case 1[Deployment]
B. Antenna: Multiple-Input and Multiple-Output (MIMO), [2D, 3D]
C. Mobility: [3km/h, 30km/h]
D. Transmission bandwidth: 10Mhz
Sarker & Johansson Expires December 13, 2015 [Page 6]
Internet-Draft RMCAT Wireless Test Cases June 2015
E. Number of cells: multi cell deployment (3 Cells per Base
Station (BS) * 7 BS) = 21 cells
F. Cell radius: 166.666 Meters
G. Scheduler: Proportional fair with no priority
H. Bearer: Default bearer for all traffic.
I. Active Queue Management (AQM) settings: AQM [on,off]
2. End to end Round Trip Time (RTT): [ 40, 150]
3. User arrival model: Poisson arrival model
4. User intensity:
* Downlink user intensity: {0.7, 1.4, 2.1, 2.8, 3.5, 4.2, 4.9,
5.6, 6.3, 7.0, 7.7, 8.4, 9,1, 9.8, 10.5}
* Uplink user intercity : {0.7, 1.4, 2.1, 2.8, 3.5, 4.2, 4.9,
5.6, 6.3, 7.0}
5. Simulation duration: 91s
6. Evaluation period : 30s-60s
7. Media traffic
1. Media type: Video
a. Media direction: [Uplink, Downlink]
b. Number of Media source per user: One (1)
c. Media duration per user: 30s
d. Media source: same as define in section 4.3 of
[I-D.ietf-rmcat-eval-test]
2. Media Type : Audio
a. Media direction: Uplink and Downlink
b. Number of Media source per user: One (1)
c. Media duration per user: 30s
Sarker & Johansson Expires December 13, 2015 [Page 7]
Internet-Draft RMCAT Wireless Test Cases June 2015
d. Media codec: Constant BitRate (CBR)
e. Media bitrate : 20 Kbps
f. Adaptation: off
8. Other traffic model:
* Downlink simulation: Maximum of 4Mbps/cell (web browsing or
FTP traffic)
* Unlink simulation: Maximum of 2Mbps/cell (web browsing or FTP
traffic)
3.2. Bad Radio Coverage
The goal of this test is to evaluate the performance of candidate
congestion control algorithm when users visit part of the network
with bad radio coverage. The scenario is created by using larger
cell radius than previous test case. In this test case each of the
user/UE in the media session is an RMCAT compliant endpoint. The
arrival of users follows a Poisson distribution, which is
proportional to the length of the call, so that the number of users
per cell is kept fairly constant during the evaluation period. At
the beginning of the simulation there should be enough amount of time
to warm-up the network. This is to avoid running the evaluation in
an empty network where network nodes are having empty buffers, low
interference at the beginning of the simulation. This network
initialization period is therefore excluded from the evaluation
period.
This test case also includes user mobility and competing traffic.
The competing traffics includes same kind of flows (with same
adaptation algorithms) . The investigated congestion control
algorithms should show maximum possible network utilization and
stability in terms of rate variations, lowest possible end to end
frame latency, network latency and Packet Loss Rate (PLR) at
different cell load level.
3.2.1. Network connection
Same as defined in Section 3.1.1
3.2.2. Simulation Setup
The desired simulation setup is same as Varying Network Load test
case defined in Section 3.1 except following changes-
Sarker & Johansson Expires December 13, 2015 [Page 8]
Internet-Draft RMCAT Wireless Test Cases June 2015
1. Radio environment : Same as defined in Section 3.1.2 except
followings
A. Deployment and propagation model : 3GPP case 3[Deployment]
B. Cell radius: 577.3333 Meters
C. Mobility: 3km/h
2. User intensity = {0.7, 1.4, 2.1, 2.8, 3.5, 4.2, 4.9, 5.6, 6.3,
7.0}
3. Media traffic model: Same as defined in Section 3.1.2
4. Other traffic model: None
3.3. Desired Evaluation Metrics for cellular test cases
RMCAT evaluation criteria document [I-D.ietf-rmcat-eval-criteria]
defines metrics to be used to evaluate candidate algorithms.
However, looking at the nature and distinction of cellular networks
we recommend at minimum following metrics to be used to evaluate the
performance of the candidate algorithms for the test cases defined in
this document.
The desired metrics are-
o Average cell throughput (for all cells), shows cell utilizations.
o Application sending and receiving bitrate, goodput.
o Packet Loss Rate (PLR).
o End to end Media frame delay. For video, this means the delay
from capture to display.
o Transport delay.
o Algorithm stability in terms of rate variation.
4. Wi-Fi Networks Specific Test Cases
TBD
Sarker & Johansson Expires December 13, 2015 [Page 9]
Internet-Draft RMCAT Wireless Test Cases June 2015
5. Conclusion
This document defines two test cases that are considered important
for cellular networks. Moreover, this document also provides a
framework to define more additional test cases for cellular network.
6. Acknowledgements
We would like to thank Tomas Frankkila, Magnus Westerlund, Kristofer
Sandlund for their valuable comments while writing this draft.
7. IANA Considerations
This memo includes no request to IANA.
8. Security Considerations
Security issues have not been discussed in this memo.
9. References
9.1. Normative References
[Deployment]
TS 25.814, 3GPP., "Physical layer aspects for evolved
Universal Terrestrial Radio Access (UTRA)", October 2006,
<http://www.3gpp.org/ftp/specs/
archive/25_series/25.814/25814-710.zip>.
[HO-def-3GPP]
TR 21.905, 3GPP., "Vocabulary for 3GPP Specifications",
December 2009, <http://www.3gpp.org/ftp/specs/
archive/21_series/21.905/21905-940.zip>.
[HO-LTE-3GPP]
TS 36.331, 3GPP., "E-UTRA- Radio Resource Control (RRC);
Protocol specification", December 2011,
<http://www.3gpp.org/ftp/specs/
archive/36_series/36.331/36331-990.zip>.
[HO-UMTS-3GPP]
TS 25.331, 3GPP., "Radio Resource Control (RRC); Protocol
specification", December 2011,
<http://www.3gpp.org/ftp/specs/
archive/25_series/25.331/25331-990.zip>.
Sarker & Johansson Expires December 13, 2015 [Page 10]
Internet-Draft RMCAT Wireless Test Cases June 2015
[I-D.ietf-rmcat-eval-criteria]
Singh, V. and J. Ott, "Evaluating Congestion Control for
Interactive Real-time Media", draft-ietf-rmcat-eval-
criteria-03 (work in progress), March 2015.
[QoS-3GPP]
TS 23.203, 3GPP., "Policy and charging control
architecture", June 2011, <http://www.3gpp.org/ftp/specs/
archive/23_series/23.203/23203-990.zip>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
9.2. Informative References
[I-D.ietf-rmcat-cc-requirements]
Jesup, R. and Z. Sarker, "Congestion Control Requirements
for Interactive Real-Time Media", draft-ietf-rmcat-cc-
requirements-09 (work in progress), December 2014.
[I-D.ietf-rmcat-eval-test]
Sarker, Z., Singh, V., Zhu, X., and M. Ramalho, "Test
Cases for Evaluating RMCAT Proposals", draft-ietf-rmcat-
eval-test-01 (work in progress), March 2015.
[IEEE802.11]
"Standard for Information technology--Telecommunications
and information exchange between systems Local and
metropolitan area networks--Specific requirements Part 11:
Wireless LAN Medium Access Control (MAC) and Physical
Layer (PHY) Specifications", 2012.
[LTE-simulator]
"NS-3, A discrete-Event Network Simulator",
<https://www.nsnam.org/docs/release/3.23/manual/html/
index.html>.
Authors' Addresses
Zaheduzzaman Sarker
Ericsson AB
Laboratoriegraend 11
Luleae 97753
Sweden
Phone: +46 107173743
Email: zaheduzzaman.sarker@ericsson.com
Sarker & Johansson Expires December 13, 2015 [Page 11]
Internet-Draft RMCAT Wireless Test Cases June 2015
Ingemar Johansson
Ericsson AB
Laboratoriegraend 11
Luleae 97753
Sweden
Phone: +46 10 7143042
Email: ingemar.s.johansson@ericsson.com
Sarker & Johansson Expires December 13, 2015 [Page 12]