Internet Draft Andy Bierman
Cisco Systems, Inc.
12 May 2000
Remote Monitoring MIB Extensions for
Differentiated Services
<draft-ietf-rmonmib-dsmon-mib-01.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC2026 [RFC2026].
Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups. Note that other groups
may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet- Drafts as reference material
or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Distribution of this document is unlimited. Please send comments to the
RMONMIB WG mailing list <rmonmib@cisco.com>.
1. Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved.
Internet-Draft DSMON MIB May 2000
2. Abstract
This memo defines an experimental portion of the Management Information
Base (MIB) for use with network management protocols in the Internet
community. In particular, it describes managed objects used for
monitoring Differentiated Services Codepoint usage in IP packets,
utilizing the monitoring framework defined in the RMON-2 MIB [RFC2021].
3. Table of Contents
1 Copyright Notice ................................................ 1
2 Abstract ........................................................ 2
3 Table of Contents ............................................... 2
4 The SNMP Network Management Framework ........................... 2
5 Overview ........................................................ 3
5.1 Terms ......................................................... 4
5.2 Relationship to Differentiated Services ....................... 5
5.3 Relationship to the Remote Monitoring MIBs .................... 5
5.4 MIB Structure ................................................. 7
5.4.1 DSCP Aggregation Control Group .............................. 7
5.4.2 DS Statistics Group ......................................... 8
5.4.3 DS Protocol Distribution Group .............................. 8
5.4.4 DS Host Distribution Group .................................. 9
6 Definitions ..................................................... 10
7 Intellectual Property ........................................... 66
8 Acknowledgements ................................................ 66
9 References ...................................................... 66
10 Security Considerations ........................................ 69
11 Author's Address ............................................... 70
12 Full Copyright Statement ....................................... 71
4. The SNMP Network Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
RFC 1155 [RFC1155], RFC 1212 [RFC1212] and RFC 1215 [RFC1215].
The second version, called SMIv2, is described in RFC 2578
[RFC2578], RFC 2579 [RFC2579] and RFC 2580 [RFC2580].
Expires November 2000 [Page 2]
Internet-Draft DSMON MIB May 2000
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in RFC 1157 [RFC1157]. A second version of the SNMP
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
and RFC 1906 [RFC1906]. The third version of the message
protocol is called SNMPv3 and described in RFC 1906 [RFC1906],
RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in RFC 1157 [RFC1157]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[RFC1905].
o A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism described
in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
5. Overview
There is a need for a standardized way of monitoring the network traffic
usage of Differentiated Services (DS) [RFC2474] codepoint values. Each
DS codepoint (DSCP) value may be given a different preference by a
forwarding device, and this affects which packets get dropped or delayed
during periods of network congestion.
Expires November 2000 [Page 3]
Internet-Draft DSMON MIB May 2000
The IETF DIFFSERV working group has redefined the semantics of the Type
of Service (TOS) octet in the IP header, which is now called the 'DS
field'. The 6-bit Codepoint (DSCP) portion is contained in the DS field,
which provides for 64 different packet treatments for the implementation
of differentiated network services. The actual packet treatment, or per-
hop behavior (PHB), applied by a forwarding device, is independent of a
particular DSCP value.
By polling DSCP usage counters, an NMS can determine the network
throughput for traffic associated with different DSCPs. This data can
then be analyzed in order to 'tune' DSCP 'allocations' within a network,
based on the Quality of Service (QoS) policies for that network.
5.1. Terms
This document uses some terms that need introduction:
DataSource
A source of data for monitoring purposes. This term is used exactly
as defined in the RMON-2 MIB [RFC2021].
protocol
A specific protocol encapsulation, as identified for monitoring
purposes. This term is used exactly as defined in the RMON
Protocol Identifiers document [RFC2074].
Aggregation Group
An arbitrary set of DSCP values, grouped together for counting
purposes. This term is not related to the term 'Behavior
Aggregate', or any other use of the term 'Aggregate' in the
DIFFSERV WG [RFC2474]. An aggregation group may be used to model a
particular per-hop behavior (PHB), but specific PHBs are not
enumerated in this document, in order to reduce the coupling
between this document and documents produced by the DIFFSERV WG.
Also, new PHBs will likely be added over time, making static
assignments in this MIB impractical.
For the purposes of this MIB, a aggregation group is simply a group
of codepoints that are being counted in the same manner (i.e., same
buckets), for the purpose of (potentially) reducing the number of
MIB objects that a management station must retrieve.
Expires November 2000 [Page 4]
Internet-Draft DSMON MIB May 2000
5.2. Relationship to Differentiated Services
The DS-MON MIB focuses only on the DSCP values used in IP packets on a
monitored dataSource. The per-hop behavior (PHB) associated with each
DSCP may be different at each DS-capable forwarding device in the
network.
This MIB does not address the following Differentiated Services issues
in any way:
- configuration and characterization of each PHB in each device
- identification of the mapping between DSCPs and PHBs in each device
- identification of DS capabilities of each forwarding device
- characterization of DSCP values or PHBs, as they relate to standard
or proprietary QoS policy and deployment strategy.
It is expected that such a MIB (targeted for DS-capable forwarding
devices) will be developed by the DIFFSERV working group to address
these issues.
It is also desirable to keep the monitoring of DSCP usage independent of
the DS forwarding devices, in order to keep probe placement more
flexible, which, in turn, enables better statistics aggregation by the
probe.
This document assumes the reader is somewhat familiar with the DS
Architecture [RFC2475], but the DS-MON MIB addresses only the aspects of
monitoring DSCP usage, and therefore is completely decoupled from the
larger issues of network-wide DS configuration and performance analysis.
It is expected that complex NMS applications will use the counters in
this MIB to help analyze DS-related throughput. It is expected that
other metrics, such as delay and jitter, will also be analyzed, but
support for other metrics is outside the scope of this document.
5.3. Relationship to the Remote Monitoring MIBs
This MIB is intended to be implemented in Remote Monitoring (RMON)
probes, which implement the RMON-2 MIB [RFC2021]. Such probes may be
stand-alone devices, or may not be co-located with other networking
devices (e.g., ethernet switches and repeaters).
Expires November 2000 [Page 5]
Internet-Draft DSMON MIB May 2000
The DS-MON probe must be capable of parsing the DS field in IP packets
and correlating the embedded DSCP value with other statistics, as
defined in the DS-MON MIB. The DS-MON functions are intended to be
implemented in conjunction with the associated RMON functions, but the
MIB is independent of all other RMON data tables. For example, an agent
might wish to implement the RMON-2 protocol distribution group and the
DS-MON protocol distribution group, in order to provide the fine
granularity, 'per DSCP' statistics with the DS-MON MIB, and the 'grand
total' statistics with the RMON-2 MIB.
Several concepts and even MIB objects from the RMON MIBs are used in the
DS-MON MIB:
DataSource
This textual convention is used to describe the identification of
an RMON monitoring source (defined in the RMON-2 MIB [RFC2021]).
The DataSource textual convention is used throughout the DS-MON MIB
to identify the monitoring source for each configured collection.
A DataSource MIB object is an OBJECT IDENTIFIER, which contains the
particular instance of the ifIndex object associated with the
monitored dataSource.
Protocol Directory
The RMON-2 MIB [RFC2021] defines the protocolDirTable, which is a
directory of all the protocols that the RMON-2 agent is capable of
decoding and counting. The DS-MON MIB utilizes this directory to
identify the protocols detected in monitored packets.
TimeFilter
The RMON-2 TimeFilter textual convention provides a mechanism to
retrieve only rows which have been created or modified since the
last polling interval (for a particular NMS). The DS-MON MIB uses
this textual convention in the large data tables, in order to
minimize polling impact.
Zero-Based Counters
Since counters are instantiated by management action, as in the
RMON MIBs, the DS-MON MIB uses zero-based counters in all data
collection tables. Specifically, the ZeroBasedCounter32 textual
convention from the RMON-2 MIB [RFC2021] and the ZeroBasedCounter64
textual convention (defined in the HC-RMON MIB [HC-RMON]) are used
to define counter objects in this MIB.
High Capacity Counters
The DS-MON MIB uses the same 'SNMPv1 coexistence' strategy as the
Expires November 2000 [Page 6]
Internet-Draft DSMON MIB May 2000
RMONMIB WG. That is, where a 64-bit counter is provided, a 32-bit
version of the counter, and a 32-bit overflow counter are also
provided.
TopN Reports
The DS-MON MIB uses the same TopN reporting MIB structure as the
RMON-2 MIB [RFC2021]. TopN reporting can greatly reduce the polling
overhead required to analyze DSCP usage patterns.
5.4. MIB Structure
The DS-MON MIB contains three groups of MIB objects:
- dsmonAggregateControl group
Controls the configuration of Aggregation Groups, for the purpose
of reducing the total number of counters maintained by the agent.
- dsmonStatsObjects group
Report per Aggregation Group distribution statistics for a
particular RMON dataSource.
- dsmonPdistObjects group
Report per Aggregation Group distribution statistics for each
protocol detected on a particular RMON dataSource.
- dsmonHostObjects group
Report IP host address distribution statistics for each Aggregation
Group, detected on a particular RMON dataSource.
5.4.1. DSCP Aggregation Control Group
This group contains 4 scalar objects and two tables, and is used by an
NMS to configure each DS codepoint to be counted in exactly one
aggregation group.
The dsmonMaxAggGroups scalar is a read-only integer which indicates the
maximum number of aggregation groups that can be configured on this
agent. This value should be equal to the number of codepoints (64), but
an agent may limit the number of aggregation groups because of resource
limitations (e.g., small number of HW-based counters). At leasst two
aggregation groups must be supported by the agent.
The dsmonAggControlLocked scalar is used as a top level switch,
Expires November 2000 [Page 7]
Internet-Draft DSMON MIB May 2000
controlling access to the dsmonAggControlTable. All DS-MON data is
deleted, and collection suspended, while this object is equal to
'false', since the meaning of one or more aggregation groups may change
when it is set back to 'true'.
The dsmonAggControlChanges counter and dsmonAggControlLastChangeTime
timestamp can be used by a management station to detect that the
codepoint to aggregation group mappings may have changed between polls.
The dsmonAggControlTable contains 64 rows, one for each DSCP value. Each
row contains the aggregation group index for that codepoint (also in the
range 0..63). The default assignment is 'Row(x) = x', which results in
no aggregation at all.
The dsmonAggDescrTable contains an administratively assigned descriptive
label for each configured aggregation group.
5.4.2. DS Statistics Group
This group contains two tables, the dsmonStatsControlTable and the
dsmonStatsTable, and supports Aggregation Group distribution statistics
for half and full-duplex, low and high speed interfaces. Packet and
octets distributions (by Aggregation Group) are maintained in the
dsmonStatsTable for each active control row in the
dsmonStatsControlTable.
This group provides the lowest statistics granularity in the DS-MON MIB.
It is expected than NMS applications will analyze certain DS deployment
or performance problems by first examining the Aggregation Group
distribution for an entire interface with this group.
5.4.3. DS Protocol Distribution Group
This group contains two tables for statistics collection,
(dsmonPdistControlTable and dsmonPdistStatsTable), and two tables for a
'Top N' reporting function for the collected statistics
(dsmonPdistTopNControlTable and dsmonPdistTopNTable).
The dsmonPdistControlTable and dsmonPdistStatsTable tables provide
Aggregation Group distribution statistics for each selected protocol
encapsulation in packets monitored on a particular dataSource. Packet
and octets distributions (per protocol per Aggregation Group) are
maintained in the dsmonPdistStatsTable for each active control row in
the dsmonPdistControlTable.
Expires November 2000 [Page 8]
Internet-Draft DSMON MIB May 2000
Due the potentially large number of entries, the DS Protocol
Distribution is different from the RMON-2 protocol distribution group in
several ways:
- maximum desired entries parameter added to the control table
- inserts and deletes counters added to the control table
- support for LRU garbage collection in the dsmonPdistStatsTable
- TimeFilter index added to the dsmonPdistStatsTable
- the selection of protocols is not configurable. Rather than select
individual protocols to monitor, (e.g., via a 'supportedOn/Off'
extension to the protocolDirTable [RFC 2021]), a simplified
configuration mechanism is provided. Since DSCP usage statistics
are most interesting at the application layer, the
dsmonPdistStatsTable is 'hardwired' to select only application
layer (i.e., 'terminal') protocols for statistical analysis.
The TopN feature requires two additional tables: the
dsmonPdistTopNControlTable and the dsmonPdistTopNTable, and supports
periodic usage reporting for the statistics maintained in the
dsmonPdistStatsTable. This feature allows for simple periodic retrieval
of the most used application/Aggregation Group combinations.
5.4.4. DS Host Distribution Group
This group contains two tables for statistics collection,
(dsmonHostControlTable and dsmonHostTable), and two tables for a 'Top N'
reporting function for the collected statistics
(dsmonHostTopNControlTable and dsmonHostTopNTable).
The dsmonHostControlTable and dsmonHostTables provide IP host
distribution statistics for each Aggregation Group detected in packets
monitored on a particular dataSource.
It is expected than NMS applications will analyze certain DS deployment
or performance problems by first determining the high priority DSCP
values to examine (beyond the scope of this document) and then examining
the dsmonHostTable statistics to determine which IP hosts are using the
selected Aggregation Groups.
Expires November 2000 [Page 9]
Internet-Draft DSMON MIB May 2000
Packet and octets distributions (in and out, per DSCP per IP host) are
maintained in the dsmonHostTable for each active control row in the
dsmonHostControlTable.
The DS Host Distribution is different from the RMON-2 network layer host
group in two ways:
- there is no protocolDirLocalIndex in the dsmonHostTable INDEX,
since only IPv4 and IPv6 packets contain a DS field, the protocol
(IPv4 or IPv6) is determined by the length of each dsmonHostAddress
instance.
- the dsmonHostControlTable supports limited IPv4 subnet aggregation
by allowing the number of 'monitored address bits' in each address
to be configured for each collection. The agent will zero out the
selected number of rightmost IPv4 address bits for counting
purposes. This configuration parameter can dramatically reduce the
number of entries which must be maintained by the agent, which
should reduce CPU and memory resource requirements on the agent,
and reduce polling overhead on the network and the management
station.
The TopN feature requires two additional tables: the
dsmonHostTopNControlTable and the dsmonHostTopNTable. and supports
periodic usage reporting for the statistics maintained in the
dsmonHostTable. This feature allows for simple periodic retrieval of
the most used IP-host/DSCP combinations.
6. Definitions
-- RMON-2 Extensions for the Monitoring of Differentiated Services
-- Enabled Networks
--
-- IP DIFFSERV DSCP statistics
-- * Per Aggregation Group
-- * Per Protocol Per Aggregation Group
-- * Per Aggregation Group Per IP Host Address
--
--
DSMON-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32,
Expires November 2000 [Page 10]
Internet-Draft DSMON MIB May 2000
Counter32, Gauge32, Counter64
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, TimeStamp, TEXTUAL-CONVENTION, TruthValue,
FROM SNMPv2-TC
OwnerString
FROM IF-MIB
rmon
FROM RMON-MIB
protocolDirLocalIndex, LastCreateTime,
DataSource, ZeroBasedCounter32, TimeFilter
FROM RMON2-MIB
CounterBasedGauge64, ZeroBasedCounter64
FROM HCNUM-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB;
dsmonMIB MODULE-IDENTITY
LAST-UPDATED "200005120000Z"
ORGANIZATION "IETF RMONMIB Working Group"
CONTACT-INFO
" Andy Bierman
Cisco Systems, Inc.
Postal: 170 West Tasman Drive
San Jose, CA USA 95134
Tel: +1 408 527-3711
E-mail: abierman@cisco.com
Send comments to <rmonmib@cisco.com>
Subscribe: majordomo@cisco.com
Msg body: subscribe rmonmib"
DESCRIPTION
"This module defines Remote Monitoring MIB extensions for
Differentiated Services enabled networks."
REVISION "200005120000Z"
DESCRIPTION
"Initial version of the DS-MON MIB module. This version
published as RFC xxxx (to be assigned by the RFC Editor)."
::= { rmon 26 }
dsmonObjects OBJECT IDENTIFIER ::= { dsmonMIB 1 }
dsmonNotifications OBJECT IDENTIFIER ::= { dsmonMIB 2 }
dsmonConformance OBJECT IDENTIFIER ::= { dsmonMIB 3 }
Expires November 2000 [Page 11]
Internet-Draft DSMON MIB May 2000
dsmonAggObjects OBJECT IDENTIFIER ::= { dsmonObjects 1 }
dsmonStatsObjects OBJECT IDENTIFIER ::= { dsmonObjects 2 }
dsmonPdistObjects OBJECT IDENTIFIER ::= { dsmonObjects 3 }
dsmonHostObjects OBJECT IDENTIFIER ::= { dsmonObjects 4 }
--
-- Extensions to the RMON-2 MIB for Differentiated Services
-- Monitoring
--
-- In order to maintain the RMON 'look-and-feel', some of
-- the text from the RMON-2 and HC-RMON MIBs by
-- Steve Waldbusser has been used in this MIB.
--
--
-- Textual Convention to define a DSCP for
-- monitoring purposes
--
DSCodePoint ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes an object which identifies the
Differentiated Services Codepoint (DSCP) value in an IPv4 or
IPv6 packet header."
REFERENCE
"Definition of the Differentiated Services Field (DS Field)
in the IPv4 and IPv6 Headers [RFC2474]."
SYNTAX Integer32 (0..63)
AggGroupIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes an object which identifies an arbitrary
grouping of DSCP values, for monitoring purposes only."
SYNTAX Integer32 (0..63)
-- ***********************************************************
-- * *
-- * A G G R E G A T I O N C O N T R O L G R O U P S *
-- * *
-- ***********************************************************
Expires November 2000 [Page 12]
Internet-Draft DSMON MIB May 2000
dsmonMaxAggGroups OBJECT-TYPE
SYNTAX Integer32 (2..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of Aggregation Groups that this agent
can support. The agent will allow this number of distinct
groups to be configured in the dsmonAggControlTable,
numbered from '0' to 'dsmonMaxAggGroups - 1'.
The agent may not lower this value during system operation,
and should set this object to an appropriate value during
system initialization."
::= { dsmonAggObjects 1 }
dsmonAggControlLocked OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the setup of Aggregation Groups for this agent.
If this object contains the value 'true', then the objects
in the dsmonAggControlTable may not be modified in any way
by a management station.
If this object contains the value 'false', then the objects
in the dsmonAggControlTable may be modified by a management
station.
While this object contains the value 'false', all objects in
all DS-MON data tables (e.g., dsmonStatsTable) shall be
deleted, and the agent will not count any packets
whatsoever, on behalf of any configured DS-MON collections.
An agent is not required to process SNMP Set Requests for
this object in conjunction with other objects from this MIB.
This is intended to simplify the processing of Set Requests
for the dsmonAggControlTable, by eliminating the possibility
that a single Set PDU will contain multiple varbinds which
are in conflict. (E.g., a PDU which both modifies the
dsmonAggControlTable and locks the dsmonAggControlTable at
the same time.)"
DEFVAL { false }
::= { dsmonAggObjects 2 }
Expires November 2000 [Page 13]
Internet-Draft DSMON MIB May 2000
dsmonAggControlChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times the value of the
dsmonAggControlLocked object has changed. A management
station can use this object to detect if counters in the DS-
MON data tables (e.g., dsmonStatsEntry) have been deleted
and recreated between polls.
This object shall be incremented by one each time the
dsmonAggControlLocked object changes from 'false' to 'true',
or from 'true' to 'false'."
::= { dsmonAggObjects 3 }
dsmonAggControlLastChangeTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the value of sysUpTime at the moment
the dsmonAggControlLocked object was last modified. A
management station can use this object to detect if counters
in the DS-MON data tables (e.g., dsmonStatsEntry) have been
deleted and recreated between polls.
This object shall be updated with the current value of
sysUpTime, if the dsmonAggControlLocked object changes from
'false' to 'true', or from 'true' to 'false'.
Upon system initialization, this object shall contain the
value zero."
::= { dsmonAggObjects 4 }
--
-- Aggregation Group Control Table
--
dsmonAggControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Expires November 2000 [Page 14]
Internet-Draft DSMON MIB May 2000
"Controls the setup of Aggregation Groups for this agent.
Each DSCP value must be configured into exactly one
Aggregation Group.
This table may only be modified if the dsmonAggControlLocked
object is equal to 'false'.
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table should be
initialized with the saved values. Otherwise, an agent
should default to no aggregation at all, by initially
configuring each DSCP value in its own aggregation group,
identified by the DSCP value. (e.g., DSCP 14 in aggregation
group 14)."
::= { dsmonAggObjects 5 }
dsmonAggControlEntry OBJECT-TYPE
SYNTAX DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggControlTable."
INDEX { dsmonAggControlDSCP }
::= { dsmonAggControlTable 1 }
DsmonAggControlEntry ::= SEQUENCE {
dsmonAggControlDSCP DSCodePoint,
dsmonAggGroupIndex AggGroupIndex
}
dsmonAggControlDSCP OBJECT-TYPE
SYNTAX DSCodePoint
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The specific DSCP value which is configured in an
Aggregation Group by this entry."
::= { dsmonAggControlEntry 1 }
dsmonAggGroupIndex OBJECT-TYPE
SYNTAX AggGroupIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Aggregation Group which contains this DSCP value. This
Expires November 2000 [Page 15]
Internet-Draft DSMON MIB May 2000
object may not be modified if the dsmonAggControlLocked
object is equal to 'true'."
::= { dsmonAggControlEntry 2 }
--
-- Aggregation Group Description Table
--
dsmonAggDescrTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggDescrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides a description of each configured
aggregation group. It should be configured at the same time
the dsmonAggControlTable is configured.
This table may only be modified if the dsmonAggControlLocked
object is equal to 'false'.
If the agent supports non-volatile configuration of this
table, then upon system initialization, the table should be
initialized with the saved values. Otherwise, each
potential aggregation group description string should
contain the empty string."
::= { dsmonAggObjects 6 }
dsmonAggDescrEntry OBJECT-TYPE
SYNTAX DsmonAggDescrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggDescrTable. The
dsmonAggGroupIndex INDEX identifies the aggregation group
associated with each entry. Entries with a
dsmonAggGroupIndex INDEX value greater or equal to the value
of the dsmonMaxAggGroups object shall contain the empty
string."
INDEX { dsmonAggGroupIndex }
::= { dsmonAggDescrTable 1 }
DsmonAggDescrEntry ::= SEQUENCE {
dsmonAggGroupDescr SnmpAdminString
}
Expires November 2000 [Page 16]
Internet-Draft DSMON MIB May 2000
dsmonAggGroupDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An administratively assigned description of this
aggregation group. The agent will only allow entries to be
modified which have a dsmonAggGroupIndex value less than the
value of the dsmonMaxAggGroups object.
Upon first instantiation of this object, the agent should
set this object to the empty string. If the agent supports
non-volatile storage, then this object should be re-
initialized with its stored value after a system reboot."
::= { dsmonAggDescrEntry 1 }
-- ***********************************************************
-- * *
-- * P E R - D A T A S O U C E C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- Per-DataSource Statistics Control Table
--
dsmonStatsControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per-data source per Aggregation Group
distribution statistics."
::= { dsmonStatsObjects 1 }
dsmonStatsControlEntry OBJECT-TYPE
SYNTAX DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonStatsControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonStatsControlStatus
Expires November 2000 [Page 17]
Internet-Draft DSMON MIB May 2000
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonStatsTable to be created and maintained by
the agent."
INDEX { dsmonStatsControlIndex }
::= { dsmonStatsControlTable 1 }
DsmonStatsControlEntry ::= SEQUENCE {
dsmonStatsControlIndex Integer32,
dsmonStatsControlDataSource DataSource,
dsmonStatsControlDroppedFrames Counter32,
dsmonStatsControlCreateTime LastCreateTime,
dsmonStatsControlOwner OwnerString,
dsmonStatsControlStatus RowStatus
}
dsmonStatsControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonStatsControlEntry."
::= { dsmonStatsControlEntry 1 }
dsmonStatsControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the this per-protocol per
Aggregation Group distribution.
The statistics in this group reflect all IPv4 and IPv6
packets on the local network segment attached to the
identified interface.
This object may not be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 2 }
dsmonStatsControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
Expires November 2000 [Page 18]
Internet-Draft DSMON MIB May 2000
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonStatsControlEntry 3 }
dsmonStatsControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonStatsControlEntry 4 }
dsmonStatsControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonStatsControlEntry 5 }
dsmonStatsControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry may not exist in the active state unless all
Expires November 2000 [Page 19]
Internet-Draft DSMON MIB May 2000
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonStatsTable shall be deleted."
::= { dsmonStatsControlEntry 6 }
--
-- Per-DataSource Statistics Table
--
dsmonStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Per Protocol per Aggregation Group
usage.
The following table defines per-Aggregation Group statistics
for full and/or half-duplex links as well as high capacity
links.
For half-duplex links, or full-duplex-capable links
operating in half-duplex mode, the dsmonStatsIn* objects
shall be used and the dsmonStatsOut* objects will not
increment.
For full-duplex links, the dsmonStatsOut* objects will be
present. Whenever possible, the probe should count packets
moving away from the closest terminating equipment as output
packets. Failing that, the probe should count packets moving
away from the DTE as output packets.
If the dsmonAggControlLocked object is equal to 'true', then
all entries in this table will be deleted and the agent will
not process packets on behalf of any
dsmonStatsControlEntry."
::= { dsmonStatsObjects 2 }
dsmonStatsEntry OBJECT-TYPE
SYNTAX DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
Expires November 2000 [Page 20]
Internet-Draft DSMON MIB May 2000
usage, containing inbound and outbound packet and octet
counters for each Aggregation Group configured for
collection.
The dsmonStatsControlIndex value in the index identifies the
dsmonStatsControlEntry on whose behalf this entry was
created.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggControlTable entry for that DSCP value.
Note that only protocols which are encapsulated in IPv4 or
IPv6 packets will be counted in this table.
An example of the indexing of this entry is
dsmonStatsOutPkts.1.16"
INDEX { dsmonStatsControlIndex, dsmonAggGroupIndex }
::= { dsmonStatsTable 1 }
DsmonStatsEntry ::= SEQUENCE {
dsmonStatsInPkts ZeroBasedCounter32,
dsmonStatsInOctets ZeroBasedCounter32,
dsmonStatsInOvflPkts ZeroBasedCounter32,
dsmonStatsInOvflOctets ZeroBasedCounter32,
dsmonStatsInHCPkts ZeroBasedCounter64,
dsmonStatsInHCOctets ZeroBasedCounter64,
dsmonStatsOutPkts ZeroBasedCounter32,
dsmonStatsOutOctets ZeroBasedCounter32,
dsmonStatsOutOvflPkts ZeroBasedCounter32,
dsmonStatsOutOvflOctets ZeroBasedCounter32,
dsmonStatsOutHCPkts ZeroBasedCounter64,
dsmonStatsOutHCOctets ZeroBasedCounter64
}
dsmonStatsInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated aggregation group, received on a half-duplex link
or on the inbound connection of a full-duplex link."
::= { dsmonStatsEntry 1 }
Expires November 2000 [Page 21]
Internet-Draft DSMON MIB May 2000
dsmonStatsInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, received on a
half-duplex link or on the inbound connection of a full-
duplex link."
::= { dsmonStatsEntry 2 }
dsmonStatsInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonStatsInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 3 }
dsmonStatsInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonStatsInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 4 }
dsmonStatsInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInPkts object.
Note that this object will only be instantiated if the RMON
Expires November 2000 [Page 22]
Internet-Draft DSMON MIB May 2000
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 5 }
dsmonStatsInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 6 }
dsmonStatsOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated aggregation group, received on a full-duplex link
in the direction of the network."
::= { dsmonStatsEntry 7 }
dsmonStatsOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, received on a
full-duplex link in the direction of the network."
::= { dsmonStatsEntry 8 }
dsmonStatsOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires November 2000 [Page 23]
Internet-Draft DSMON MIB May 2000
"The number of times the associated dsmonStatsOutPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 9 }
dsmonStatsOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonStatsOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 10 }
dsmonStatsOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 11 }
dsmonStatsOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 12 }
Expires November 2000 [Page 24]
Internet-Draft DSMON MIB May 2000
-- ***********************************************************
-- * *
-- * P E R - P R O T O C O L C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- DSCP Per-Protocol Statistics Control Table
--
dsmonPdistControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per-application per Aggregation Group
distribution statistics."
::= { dsmonPdistObjects 1 }
dsmonPdistControlEntry OBJECT-TYPE
SYNTAX DsmonPdistControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonPdistControlStatus
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonPdistStatsTable to be created and maintained
by the agent."
INDEX { dsmonPdistControlIndex }
::= { dsmonPdistControlTable 1 }
DsmonPdistControlEntry ::= SEQUENCE {
dsmonPdistControlIndex Integer32,
dsmonPdistControlDataSource DataSource,
dsmonPdistControlMaxDesiredEntries Integer32,
dsmonPdistControlDroppedFrames Counter32,
dsmonPdistControlInserts Counter32,
dsmonPdistControlDeletes Counter32,
dsmonPdistControlCreateTime LastCreateTime,
dsmonPdistControlOwner OwnerString,
Expires November 2000 [Page 25]
Internet-Draft DSMON MIB May 2000
dsmonPdistControlStatus RowStatus
}
dsmonPdistControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonPdistControlEntry."
::= { dsmonPdistControlEntry 1 }
dsmonPdistControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the this per-protocol Aggregation
Group distribution.
The statistics in this group reflect all IPv4 and IPv6
packets on the local network segment attached to the
identified interface.
This object may not be modified if the associated
dsmonPdistControlStatus object is equal to active(1)."
::= { dsmonPdistControlEntry 2 }
dsmonPdistControlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonPdistStatsTable on behalf of this control entry. The
probe will not create more than this number of associated
entries in the table, but may choose to create fewer entries
in this table for any reason including the lack of
resources.
If this value is set to -1, the probe may create any number
of entries in this table.
This object may not be modified if the associated
dsmonPdistControlStatus object is equal to active(1)."
Expires November 2000 [Page 26]
Internet-Draft DSMON MIB May 2000
::= { dsmonPdistControlEntry 3 }
dsmonPdistControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonPdistControlEntry 4 }
dsmonPdistControlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been inserted
into the dsmonPdistTable. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents may
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistControlDeletes from dsmonPdistControlInserts."
::= { dsmonPdistControlEntry 5 }
dsmonPdistControlDeletes OBJECT-TYPE
Expires November 2000 [Page 27]
Internet-Draft DSMON MIB May 2000
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been deleted
from the dsmonPdist table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents may
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistControlDeletes from dsmonPdistControlInserts."
::= { dsmonPdistControlEntry 6 }
dsmonPdistControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonPdistControlEntry 7 }
dsmonPdistControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistControlEntry 8 }
dsmonPdistControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
Expires November 2000 [Page 28]
Internet-Draft DSMON MIB May 2000
DESCRIPTION
"The status of this row.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistStatsTable shall be deleted."
::= { dsmonPdistControlEntry 9 }
--
-- Per-Protocol Statistics Table
--
dsmonPdistStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on a Per Protocol per Aggregation
Group usage.
If the dsmonAggControlLocked object is equal to 'true', then
all entries in this table will be deleted and the agent will
not process packets on behalf of any
dsmonPdistControlEntry."
::= { dsmonPdistObjects 2 }
dsmonPdistStatsEntry OBJECT-TYPE
SYNTAX DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each
Aggregation Group configured for collection, and each
protocol (as identified by the protocolDirLocalIndex for the
protocol) identified in each monitored packet.
The dsmonPdistControlIndex value in the index identifies the
dsmonPdistControlEntry on whose behalf this entry was
created.
Note that only protocols which are encapsulated in IPv4 or
IPv6 packets will be counted in this table, as indicated by
Expires November 2000 [Page 29]
Internet-Draft DSMON MIB May 2000
the protocolDirTable configuration.
The agent will include only application layer protocols in
the associated dsmonPdistStatsTable. Any 'terminal' protocol
is considered to be an application protocol.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggControlTable entry for that value.
An example of the indexing of this entry is
dsmonPdistStatsPkts.9.29943.42.0."
INDEX { dsmonPdistControlIndex,
dsmonPdistTimeMark,
protocolDirLocalIndex,
dsmonAggGroupIndex }
::= { dsmonPdistStatsTable 1 }
DsmonPdistStatsEntry ::= SEQUENCE {
dsmonPdistTimeMark TimeFilter,
dsmonPdistStatsPkts ZeroBasedCounter32,
dsmonPdistStatsOctets ZeroBasedCounter32,
dsmonPdistStatsOvflPkts ZeroBasedCounter32,
dsmonPdistStatsOvflOctets ZeroBasedCounter32,
dsmonPdistStatsHCPkts ZeroBasedCounter64,
dsmonPdistStatsHCOctets ZeroBasedCounter64,
dsmonPdistStatsCreateTime LastCreateTime
}
dsmonPdistTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonPdistStatsEntry 1 }
dsmonPdistStatsPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
Expires November 2000 [Page 30]
Internet-Draft DSMON MIB May 2000
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets, using one of the DSCP values in the
indicated aggregation group, for the protocol identified by
the associated protocolDirLocalIndex value."
::= { dsmonPdistStatsEntry 2 }
dsmonPdistStatsOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, for the protocol
identified by the associated protocolDirLocalIndex value.
Note that this object doesn't count just those octets in the
particular protocol frames, but includes the entire packet
that contained the protocol."
::= { dsmonPdistStatsEntry 3 }
dsmonPdistStatsOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonPdistStatsPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCPkts object
is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 4 }
dsmonPdistStatsOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonPdistStatsOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCOctets
Expires November 2000 [Page 31]
Internet-Draft DSMON MIB May 2000
object is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 5 }
dsmonPdistStatsHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonPdistStatsEntry 6 }
dsmonPdistStatsHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonPdistStatsEntry 7 }
dsmonPdistStatsCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonPdistStats entry was
last instantiated by the agent. This can be used by the
management station to detect if the entry has been deleted
and recreated between polls."
::= { dsmonPdistStatsEntry 8 }
--
-- Per-Protocol Statistics TopN Control Table
--
Expires November 2000 [Page 32]
Internet-Draft DSMON MIB May 2000
dsmonPdistTopNControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonPdist entries according to a selected
metric."
::= { dsmonPdistObjects 3 }
dsmonPdistTopNControlEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNControlTable.
Entries are created and deleted from this table by
management action only, using the
dsmonPdistTopNControlStatus RowStatus object.
Activation of a control row in this table will cause an
associated dsmonPdistTopNTable to be created and maintained
by the agent."
INDEX { dsmonPdistTopNControlIndex }
::= { dsmonPdistTopNControlTable 1 }
DsmonPdistTopNControlEntry ::= SEQUENCE {
dsmonPdistTopNControlIndex Integer32,
dsmonPdistTopNControlPdistIndex Integer32,
dsmonPdistTopNControlRateBase INTEGER,
dsmonPdistTopNControlTimeRemaining Integer32,
dsmonPdistTopNControlGeneratedReports Counter32,
dsmonPdistTopNControlDuration Integer32,
dsmonPdistTopNControlRequestedSize Integer32,
dsmonPdistTopNControlGrantedSize Integer32,
dsmonPdistTopNControlStartTime TimeStamp,
dsmonPdistTopNControlOwner OwnerString,
dsmonPdistTopNControlStatus RowStatus
}
dsmonPdistTopNControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
Expires November 2000 [Page 33]
Internet-Draft DSMON MIB May 2000
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNControlTable. Each such entry defines one Top
N report prepared for one RMON dataSource."
::= { dsmonPdistTopNControlEntry 1 }
dsmonPdistTopNControlPdistIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonPdistTable for which a top N report will be
prepared on behalf of this entry. The dsmonPdistTable is
identified by the value of the dsmonPdistControlIndex for
that table - that value is used here to identify the
particular table.
This object may not be modified if the associated
dsmonPdistTopNControlStatus object is equal to active(1)."
::= { dsmonPdistTopNControlEntry 2 }
dsmonPdistTopNControlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonPdistTopNPkts(1),
dsmonPdistTopNOctets(2),
dsmonPdistTopNHCPkts(3),
dsmonPdistTopNHCOctets(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable for each dsmonPdist that the
dsmonPdistTopNRate and dsmonPdistTopNHCRate variables are
based upon. Each dsmonPdistTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonPdistStatsTable counter,
identified by this object.
The following table identifies the dsmonPdistTable counter
associated with each enumeration:
Enumeration RateBase MIB Object
----------- -------------------
dsmonPdistTopNPkts dsmonPdistStatsPkts
dsmonPdistTopNOctets dsmonPdistStatsOctets
Expires November 2000 [Page 34]
Internet-Draft DSMON MIB May 2000
dsmonPdistTopNHCPkts dsmonPdistStatsHCPkts
dsmonPdistTopNHCOctets dsmonPdistStatsHCOctets
Note that the dsmonPdistTopNHCPkts and
dsmonPdistTopNHCOctets enumerations are only available if
the agent supports High Capacity RMON collection.
This object may not be modified if the associated
dsmonPdistTopNControlStatus object is equal to active(1)."
::= { dsmonPdistTopNControlEntry 3 }
dsmonPdistTopNControlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonPdistTopNControlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonPdistTopNControlTimeRemaining. Thus the management
station may simply read the resulting reports repeatedly,
checking the startTime and duration each time to ensure that
a report was not missed or that the report parameters were
not changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonPdistTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonPdistTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonPdistTopNControlEntry 4 }
dsmonPdistTopNControlGeneratedReports OBJECT-TYPE
Expires November 2000 [Page 35]
Internet-Draft DSMON MIB May 2000
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonPdistTopNControlEntry 5 }
dsmonPdistTopNControlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonPdistTopNControlTimeRemaining
object is set, this object shall be set by the probe to the
same value and shall not be modified until the next time the
dsmonPdistTopNControlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonPdistTopNControlEntry."
::= { dsmonPdistTopNControlEntry 6 }
dsmonPdistTopNControlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries requested for this
report.
When this object is created or modified, the probe should
set dsmonPdistTopNControlGrantedSize as closely to this
object as is possible for the particular probe
implementation and available resources."
DEFVAL { 150 }
::= { dsmonPdistTopNControlEntry 7 }
dsmonPdistTopNControlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
Expires November 2000 [Page 36]
Internet-Draft DSMON MIB May 2000
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries in this report.
When the associated dsmonPdistTopNControlRequestedSize
object is created or modified, the probe should set this
object as closely to the requested value as is possible for
the particular implementation and available resources. The
probe must not lower this value except as a result of a set
to the associated dsmonPdistTopNControlRequestedSize object.
When the associated dsmonPdistTopNControlRequestedSize
object is created or modified, the probe should set this
object as closely to the requested value as is possible for
the particular implementation and available resources. The
probe must not lower this value except as a result of a set
to the associated dsmonPdistTopNControlRequestedSize object.
Protocol entries with the highest value of
dsmonPdistTopNRate or dsmonPdistTopNHCRate (depending on the
value of the associated dsmonPdistTopNControlRateBase
object) shall be placed in this table in decreasing order of
this rate until there is no more room or until there are no
more dsmonPdist entries."
::= { dsmonPdistTopNControlEntry 8 }
dsmonPdistTopNControlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonPdistTopNControlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonPdistTopNControlEntry 9 }
dsmonPdistTopNControlOwner OBJECT-TYPE
SYNTAX OwnerString
Expires November 2000 [Page 37]
Internet-Draft DSMON MIB May 2000
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistTopNControlEntry 10 }
dsmonPdistTopNControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonPdistTopNControlEntry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistTopNTable shall be deleted by the
agent."
::= { dsmonPdistTopNControlEntry 11 }
--
-- dsmonPdist TopN Table
--
dsmonPdistTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those protocol distribution entries
that have counted the highest number of octets or packets.
All entries in this table will be deleted if the
dsmonAggControlLocked object is equal to 'true'. The agent
will not process TopN reports on behalf of any
dsmonPdistTopNControlEntry while dsmonAggControlLocked is
equal to 'true'.
Note that dsmonPdist entries which did not increment at all
during the report interval are not included in
dsmonPdistTopN reports."
::= { dsmonPdistObjects 4 }
Expires November 2000 [Page 38]
Internet-Draft DSMON MIB May 2000
dsmonPdistTopNEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNTable.
The dsmonPdistTopNControlIndex value in the index identifies
the dsmonPdistTopNControlEntry on whose behalf this entry
was created."
INDEX { dsmonPdistTopNControlIndex, dsmonPdistTopNIndex }
::= { dsmonPdistTopNTable 1 }
DsmonPdistTopNEntry ::= SEQUENCE {
dsmonPdistTopNIndex Integer32,
dsmonPdistTopNProtocolDirLocalIndex Integer32,
dsmonPdistTopNAggGroup AggGroupIndex,
dsmonPdistTopNRate Gauge32,
dsmonPdistTopNRateOvfl Gauge32,
dsmonPdistTopNHCRate CounterBasedGauge64
}
dsmonPdistTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonPdistTopNEntry 1 }
dsmonPdistTopNProtocolDirLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with this entry."
::= { dsmonPdistTopNEntry 2 }
dsmonPdistTopNAggGroup OBJECT-TYPE
SYNTAX AggGroupIndex
MAX-ACCESS read-only
Expires November 2000 [Page 39]
Internet-Draft DSMON MIB May 2000
STATUS current
DESCRIPTION
"The DSCP Aggregation Group index value associated with
protocol identified in this entry."
::= { dsmonPdistTopNEntry 3 }
dsmonPdistTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNControlRateBase.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the the least significant 32 bits
of the associated dsmonPdistTopNHCRate object."
::= { dsmonPdistTopNEntry 4 }
dsmonPdistTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The most significant 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the upper 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero.
The agent may choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonPdistTopNEntry 5 }
dsmonPdistTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
Expires November 2000 [Page 40]
Internet-Draft DSMON MIB May 2000
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNControlRateBase.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero, and the associated
dsmonPdistTopNRate object will contain the change in the
selected variable during the sampling interval.
The agent may choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonPdistTopNEntry 6 }
-- ***********************************************************
-- * *
-- * P E R - H O S T C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- IP Host Statistics Control Table
--
dsmonHostControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls setup of per Aggregation Group, per IP host
distribution statistics."
::= { dsmonHostObjects 1 }
dsmonHostControlEntry OBJECT-TYPE
SYNTAX DsmonHostControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostControlTable.
Expires November 2000 [Page 41]
Internet-Draft DSMON MIB May 2000
Entries are created and deleted from this table by
management action only, using the dsmonHostControlStatus
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonHostTable to be created and maintained by
the agent."
INDEX { dsmonHostControlIndex }
::= { dsmonHostControlTable 1 }
DsmonHostControlEntry ::= SEQUENCE {
dsmonHostControlIndex Integer32,
dsmonHostControlDataSource DataSource,
dsmonHostControlMaxDesiredEntries Integer32,
dsmonHostControlNumAddrBits Integer32,
dsmonHostControlDroppedFrames Counter32,
dsmonHostControlInserts Counter32,
dsmonHostControlDeletes Counter32,
dsmonHostControlCreateTime LastCreateTime,
dsmonHostControlOwner OwnerString,
dsmonHostControlStatus RowStatus
}
dsmonHostControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonHostControlEntry."
::= { dsmonHostControlEntry 1 }
dsmonHostControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the associated dsmonHostTable.
The statistics in this group reflect all IPv4 and IPv6
packets on the local network segment attached to the
identified interface.
This object may not be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
Expires November 2000 [Page 42]
Internet-Draft DSMON MIB May 2000
::= { dsmonHostControlEntry 2 }
dsmonHostControlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonHostTable on behalf of this control entry. The probe
will not create more than this number of associated entries
in the table, but may choose to create fewer entries in this
table for any reason including the lack of resources.
If this value is set to -1, the probe may create any number
of entries in this table.
This object may not be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
::= { dsmonHostControlEntry 3 }
dsmonHostControlNumAddrBits OBJECT-TYPE
SYNTAX Integer32 (8..32)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the IPv4 host
address (as identified by the dsmonHostAddress object) that
should be maintained in this collection.
If this object has a value less than '32', then 'm'
rightmost bits, where 'm' is equal to '32 -
dsmonHostControlNumAddrBits', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
Note that this object only affects IPv4 host entries in the
associated dsmonHostTable. IPv6 entries are not affected by
this object.
This object may not be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
DEFVAL { 32 }
Expires November 2000 [Page 43]
Internet-Draft DSMON MIB May 2000
::= { dsmonHostControlEntry 4 }
dsmonHostControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for the associated
dsmonHost entries for whatever reason. Most often, this
event occurs when the probe is out of some resources and
decides to shed load from this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that if the dsmonHostTable is inactive because no
appropriate protocols are enabled in the protocol directory,
this value should be 0.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonHostControlEntry 5 }
dsmonHostControlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been inserted
into the dsmonHost table. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents may
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
Expires November 2000 [Page 44]
Internet-Draft DSMON MIB May 2000
dsmonHostControlDeletes from dsmonHostControlInserts."
::= { dsmonHostControlEntry 6 }
dsmonHostControlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been deleted from
the dsmonHost table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents may
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonHostControlDeletes from dsmonHostControlInserts."
::= { dsmonHostControlEntry 7 }
dsmonHostControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonHostControlEntry 8 }
dsmonHostControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostControlEntry 9 }
Expires November 2000 [Page 45]
Internet-Draft DSMON MIB May 2000
dsmonHostControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostControlEntry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTable shall be deleted."
::= { dsmonHostControlEntry 10 }
--
-- IP Host Statistics Table
--
dsmonHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of statistics for a particular IPv4 or IPv6
address that has been discovered on a particular dataSource.
The probe will add to this table all IP addresses seen as
the source or destination address in all packets with no MAC
errors, and will increment octet and packet counts in the
table for all packets with no MAC errors.
All entries in this table will be deleted if the
dsmonAggControlLocked object is equal to 'true'. The agent
will not process packets on behalf of any
dsmonHostControlEntry while dsmonAggControlLocked is equal
to 'true'."
::= { dsmonHostObjects 2 }
dsmonHostEntry OBJECT-TYPE
SYNTAX DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each
Expires November 2000 [Page 46]
Internet-Draft DSMON MIB May 2000
Aggregation Group index configured for collection per host
address, as identified in the dsmonAggControlTable.
The dsmonHostControlIndex value in the index identifies the
dsmonHostControlEntry on whose behalf this entry was
created. The length of the dsmonHostAddress field
identifies the network layer protocol as either IPv4 or
IPv6.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggControlTable entry for that value.
An example of the indexing of this entry is
dsmonHostOutPkts.1.273.32.4.171.69.120.0"
INDEX { dsmonHostControlIndex,
dsmonHostTimeMark,
dsmonAggGroupIndex,
dsmonHostAddress }
::= { dsmonHostTable 1 }
DsmonHostEntry ::= SEQUENCE {
dsmonHostTimeMark TimeFilter,
dsmonHostAddress OCTET STRING,
dsmonHostInPkts ZeroBasedCounter32,
dsmonHostInOctets ZeroBasedCounter32,
dsmonHostInOvflPkts ZeroBasedCounter32,
dsmonHostInOvflOctets ZeroBasedCounter32,
dsmonHostInHCPkts ZeroBasedCounter64,
dsmonHostInHCOctets ZeroBasedCounter64,
dsmonHostOutPkts ZeroBasedCounter32,
dsmonHostOutOctets ZeroBasedCounter32,
dsmonHostOutOvflPkts ZeroBasedCounter32,
dsmonHostOutOvflOctets ZeroBasedCounter32,
dsmonHostOutHCPkts ZeroBasedCounter64,
dsmonHostOutHCOctets ZeroBasedCounter64,
dsmonHostCreateTime LastCreateTime
}
dsmonHostTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
Expires November 2000 [Page 47]
Internet-Draft DSMON MIB May 2000
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonHostEntry 1 }
dsmonHostAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4 | 16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network address for this dsmonHostEntry.
The length of the address string is used to determine if
this entry represents an IPv4 or IPv6 address. For example,
if the length of this object is '4', then this object is
encoded as an IPv4 address in network byte order.
Note that IPv4 addresses may have some 'rightmost' bits
cleared to zero for counting purposes, as specified by the
associated dsmonHostControlNumHostBits object."
::= { dsmonHostEntry 2 }
dsmonHostInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated aggregation group, and transmitted
to this address, since this entry was added to the
dsmonHostTable. Note that this is the number of link-layer
packets, so if a single network-layer packet is fragmented
into several link-layer frames, this counter is incremented
several times."
::= { dsmonHostEntry 3 }
dsmonHostInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
Expires November 2000 [Page 48]
Internet-Draft DSMON MIB May 2000
DESCRIPTION
"The number of octets in all packets, transmitted to this
address and using one of the DSCP values in the indicated
aggregation group, since this entry was added to the
dsmonHostTable (excluding framing bits but including FCS
octets), excluding those octets in packets that contained
errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 4 }
dsmonHostInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonHostInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 5 }
dsmonHostInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonHostInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCOctets object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 6 }
dsmonHostInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInPkts object.
Expires November 2000 [Page 49]
Internet-Draft DSMON MIB May 2000
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 7 }
dsmonHostInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 8 }
dsmonHostOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated aggregation group, and transmitted
by this address, since this entry was added to the
dsmonHostTable. Note that this is the number of link-layer
packets, so if a single network-layer packet is fragmented
into several link-layer frames, this counter is incremented
several times."
::= { dsmonHostEntry 9 }
dsmonHostOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets, transmitted by this address and using
one of the DSCP values in the identified aggregation group,
since this entry was added to the dsmonHostTable (excluding
framing bits but including FCS octets), excluding those
octets in packets that contained errors.
Expires November 2000 [Page 50]
Internet-Draft DSMON MIB May 2000
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 10 }
dsmonHostOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonHostOutPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 11 }
dsmonHostOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the associated dsmonHostOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonHostEntry 12 }
dsmonHostOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 13 }
dsmonHostOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
Expires November 2000 [Page 51]
Internet-Draft DSMON MIB May 2000
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 14 }
dsmonHostCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonHost entry was last
instantiated by the agent. This can be used by the
management station to ensure that the entry has not been
deleted and recreated between polls."
::= { dsmonHostEntry 15 }
--
-- Per-Protocol Per-Host Statistics TopN Control Table
--
dsmonHostTopNControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonHost entries according to a selected
metric."
::= { dsmonHostObjects 3 }
dsmonHostTopNControlEntry OBJECT-TYPE
SYNTAX DsmonHostTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostTopNControlStatus
Expires November 2000 [Page 52]
Internet-Draft DSMON MIB May 2000
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonHostTopNTable to be created and maintained
by the agent."
INDEX { dsmonHostTopNControlIndex }
::= { dsmonHostTopNControlTable 1 }
DsmonHostTopNControlEntry ::= SEQUENCE {
dsmonHostTopNControlIndex Integer32,
dsmonHostTopNControlHostIndex Integer32,
dsmonHostTopNControlRateBase INTEGER,
dsmonHostTopNControlTimeRemaining Integer32,
dsmonHostTopNControlGeneratedReports Counter32,
dsmonHostTopNControlDuration Integer32,
dsmonHostTopNControlRequestedSize Integer32,
dsmonHostTopNControlGrantedSize Integer32,
dsmonHostTopNControlStartTime TimeStamp,
dsmonHostTopNControlOwner OwnerString,
dsmonHostTopNControlStatus RowStatus
}
dsmonHostTopNControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNControlTable. Each such entry defines one Top
N report prepared for one RMON dataSource."
::= { dsmonHostTopNControlEntry 1 }
dsmonHostTopNControlHostIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonHostTable for which a top N report will be
prepared on behalf of this entry. The dsmonHostTable is
identified by the value of the dsmonHostControlIndex for
that table - that value is used here to identify the
particular table.
This object may not be modified if the associated
dsmonHostTopNControlStatus object is equal to active(1)."
Expires November 2000 [Page 53]
Internet-Draft DSMON MIB May 2000
::= { dsmonHostTopNControlEntry 2 }
dsmonHostTopNControlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonHostTopNInPkts(1),
dsmonHostTopNInOctets(2),
dsmonHostTopNOutPkts(3),
dsmonHostTopNOutOctets(4),
dsmonHostTopNTotalPkts(5),
dsmonHostTopNTotalOctets(6),
dsmonHostTopNInHCPkts(7),
dsmonHostTopNInHCOctets(8),
dsmonHostTopNOutHCPkts(9),
dsmonHostTopNOutHCOctets(10),
dsmonHostTopNTotalHCPkts(11),
dsmonHostTopNTotalHCOctets(12)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable(s) for each dsmonHost that the
dsmonHostTopNRate and dsmonHostTopNHCRate variables are
based upon. Each dsmonHostTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonHostTable counter(s),
identified by this object.
The following table identifies the dsmonHostTable counters
associated with each enumeration:
Enumeration RateBase MIB Objects
----------- --------------------
dsmonHostTopNInPkts dsmonHostInPkts
dsmonHostTopNInOctets dsmonHostInOctets
dsmonHostTopNOutPkts dsmonHostOutPkts
dsmonHostTopNOutOctets dsmonHostOutOctets
dsmonHostTopNTotalPkts dsmonHostInPkts +
dsmonHostOutPkts
dsmonHostTopNTotalOctets dsmonHostInOctets +
dsmonHostOutOctets
dsmonHostTopNInHCPkts dsmonHostInHCPkts
dsmonHostTopNInHCOctets dsmonHostInHCOctets
dsmonHostTopNOutHCPkts dsmonHostOutHCPkts
dsmonHostTopNOutHCOctets dsmonHostOutHCPkts
dsmonHostTopNTotalHCPkts dsmonHostInHCPkts +
Expires November 2000 [Page 54]
Internet-Draft DSMON MIB May 2000
dsmonHostOutHCPkts
dsmonHostTopNTotalHCOctets dsmonHostInHCOctets +
dsmonHostOutHCOctets
The following enumerations are only available if the agent
supports High Capacity RMON collection:
dsmonHostTopNInHCPkts
dsmonHostTopNInHCOctets
dsmonHostTopNOutHCPkts
dsmonHostTopNOutHCOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
It is an implementation-specific matter whether an agent can
detect an overflow condition resulting from the addition of
two counter delta values for the following enumerations:
dsmonHostTopNTotalPkts
dsmonHostTopNTotalOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
In the event such an overflow condition can be detected by
the agent, the associated dsmonHostTopNRate,
dsmonHostTopNRateOvfl, and/or dsmonHostTopNHCRate objects
should be set to their maximum value.
This object may not be modified if the associated
dsmonHostTopNControlStatus object is equal to active(1)."
::= { dsmonHostTopNControlEntry 3 }
dsmonHostTopNControlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonHostTopNControlDuration object.
Expires November 2000 [Page 55]
Internet-Draft DSMON MIB May 2000
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonHostTopNControlTimeRemaining. Thus the management
station may simply read the resulting reports repeatedly,
checking the startTime and duration each time to ensure that
a report was not missed or that the report parameters were
not changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonHostTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonHostTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonHostTopNControlEntry 4 }
dsmonHostTopNControlGeneratedReports OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonHostTopNControlEntry 5 }
dsmonHostTopNControlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonHostTopNControlTimeRemaining object
is set, this object shall be set by the probe to the same
value and shall not be modified until the next time the
dsmonHostTopNControlTimeRemaining is set.
This value shall be zero if no reports have been requested
Expires November 2000 [Page 56]
Internet-Draft DSMON MIB May 2000
for this dsmonHostTopNControlEntry."
::= { dsmonHostTopNControlEntry 6 }
dsmonHostTopNControlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries requested for this
report.
When this object is created or modified, the probe should
set dsmonHostTopNControlGrantedSize as closely to this
object as is possible for the particular probe
implementation and available resources."
DEFVAL { 150 }
::= { dsmonHostTopNControlEntry 7 }
dsmonHostTopNControlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries in this report.
When the associated dsmonHostTopNControlRequestedSize object
is created or modified, the probe should set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
must not lower this value except as a result of a set to the
associated dsmonHostTopNControlRequestedSize object.
When the associated dsmonHostTopNControlRequestedSize object
is created or modified, the probe should set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
must not lower this value except as a result of a set to the
associated dsmonHostTopNControlRequestedSize object.
Protocol entries with the highest value of dsmonHostTopNRate
or dsmonHostTopNHCRate (depending on the value of the
associated dsmonHostTopNControlRateBase object) shall be
placed in this table in decreasing order of this rate until
Expires November 2000 [Page 57]
Internet-Draft DSMON MIB May 2000
there is no more room or until there are no more dsmonHost
entries."
::= { dsmonHostTopNControlEntry 8 }
dsmonHostTopNControlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonHostTopNControlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonHostTopNControlEntry 9 }
dsmonHostTopNControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostTopNControlEntry 10 }
dsmonHostTopNControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostTopNControlEntry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTopNTable shall be deleted by the
agent."
::= { dsmonHostTopNControlEntry 11 }
--
-- dsmonHost TopN Table
Expires November 2000 [Page 58]
Internet-Draft DSMON MIB May 2000
--
dsmonHostTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those dsmonHost entries that have
counted the highest number of octets or packets.
All entries in this table will be deleted if the
dsmonAggControlLocked object is equal to 'true'. The agent
will not process TopN reports on behalf of any
dsmonHostTopNControlEntry while dsmonAggControlLocked is
equal to 'true'.
Note that dsmonHost entries which did not increment at all
during the report interval are not included in dsmonHostTopN
reports."
::= { dsmonHostObjects 4 }
dsmonHostTopNEntry OBJECT-TYPE
SYNTAX DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNTable.
The dsmonHostTopNControlIndex value in the index identifies
the dsmonHostTopNControlEntry on whose behalf this entry was
created."
INDEX { dsmonHostTopNControlIndex, dsmonHostTopNIndex }
::= { dsmonHostTopNTable 1 }
DsmonHostTopNEntry ::= SEQUENCE {
dsmonHostTopNIndex Integer32,
dsmonHostTopNAddress OCTET STRING,
dsmonHostTopNAggGroup AggGroupIndex,
dsmonHostTopNRate Gauge32,
dsmonHostTopNRateOvfl Gauge32,
dsmonHostTopNHCRate CounterBasedGauge64
}
dsmonHostTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
Expires November 2000 [Page 59]
Internet-Draft DSMON MIB May 2000
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonHostTopNEntry 1 }
dsmonHostTopNAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4 | 16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network address of the IP host identified in this
entry. The length of this field identifies the network
layer protocol as either IPv4 or IPv6. Addresses are
encoded in network byte order."
::= { dsmonHostTopNEntry 2 }
dsmonHostTopNAggGroup OBJECT-TYPE
SYNTAX AggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Aggregation Group index value associated with host
identified in this entry."
::= { dsmonHostTopNEntry 3 }
dsmonHostTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by
dsmonHostTopNControlRateBase.
If the associated dsmonHostTopNControlRateBase indicates a
High Capacity RMON enumeration, (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
the least significant 32 bits of the associated
dsmonHostTopNHCRate object."
::= { dsmonHostTopNEntry 4 }
Expires November 2000 [Page 60]
Internet-Draft DSMON MIB May 2000
dsmonHostTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The most significant 32 bits of the associated
dsmonHostTopNHCRate object.
If the associated dsmonHostTopNControlRateBase is equal to
any of the High Capacity RMON enumerations (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
upper 32 bits of the associated dsmonHostTopNHCRate object.
If the associated dsmonHostTopNControlRateBase is not equal
to any of High Capacity RMON enumerations, then this object
will contain the value zero.
The agent may choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonHostTopNEntry 5 }
dsmonHostTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by
dsmonHostTopNControlRateBase.
If the associated dsmonHostTopNControlRateBase is not equal
to any of the High Capacity RMON enumerations (e.g.,
'dsmonHostTopNInPkts'), then this object will contain the
value zero, and the associated dsmonHostTopNRate object will
contain the change in the selected variable during the
sampling interval.
The agent may choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonHostTopNEntry 6 }
--
-- Notifications Section
Expires November 2000 [Page 61]
Internet-Draft DSMON MIB May 2000
-- (none defined)
--
--
-- Conformance Section
--
dsmonCompliances OBJECT IDENTIFIER ::= { dsmonConformance 1 }
dsmonGroups OBJECT IDENTIFIER ::= { dsmonConformance 2 }
dsmonCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB."
MODULE -- this module
MANDATORY-GROUPS { dsmonAggControlGroup, dsmonStatsGroup }
GROUP dsmonStatsHCGroup
DESCRIPTION
"The dsmonStatsHCGroup is mandatory for systems which
implement High Capacity RMON monitoring."
::= { dsmonCompliances 1 }
dsmonAggControlGroup OBJECT-GROUP
OBJECTS {
dsmonMaxAggGroups,
dsmonAggControlLocked,
dsmonAggControlChanges,
dsmonAggControlLastChangeTime,
dsmonAggGroupIndex,
dsmonAggGroupDescr
}
STATUS current
DESCRIPTION
"A collection of objects used to configure and manage
Aggregation Groups for DS-MON collection purposes."
::= { dsmonGroups 1 }
dsmonStatsGroup OBJECT-GROUP
OBJECTS {
dsmonStatsControlDataSource,
dsmonStatsControlDroppedFrames,
dsmonStatsControlCreateTime,
dsmonStatsControlOwner,
dsmonStatsControlStatus,
Expires November 2000 [Page 62]
Internet-Draft DSMON MIB May 2000
dsmonStatsInPkts,
dsmonStatsInOctets,
dsmonStatsOutPkts,
dsmonStatsOutOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics."
::= { dsmonGroups 2 }
dsmonStatsHCGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInOvflPkts,
dsmonStatsInOvflOctets,
dsmonStatsInHCPkts,
dsmonStatsInHCOctets,
dsmonStatsOutOvflPkts,
dsmonStatsOutOvflOctets,
dsmonStatsOutHCPkts,
dsmonStatsOutHCOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics for
high capacity data sources."
::= { dsmonGroups 3 }
dsmonPdistGroup OBJECT-GROUP
OBJECTS {
dsmonPdistControlDataSource,
dsmonPdistControlMaxDesiredEntries,
dsmonPdistControlDroppedFrames,
dsmonPdistControlInserts,
dsmonPdistControlDeletes,
dsmonPdistControlCreateTime,
dsmonPdistControlOwner,
dsmonPdistControlStatus,
dsmonPdistStatsPkts,
dsmonPdistStatsOctets,
dsmonPdistStatsCreateTime,
dsmonPdistTopNControlPdistIndex,
dsmonPdistTopNControlRateBase,
dsmonPdistTopNControlTimeRemaining,
dsmonPdistTopNControlGeneratedReports,
dsmonPdistTopNControlDuration,
Expires November 2000 [Page 63]
Internet-Draft DSMON MIB May 2000
dsmonPdistTopNControlRequestedSize,
dsmonPdistTopNControlGrantedSize,
dsmonPdistTopNControlStartTime,
dsmonPdistTopNControlOwner,
dsmonPdistTopNControlStatus,
dsmonPdistTopNProtocolDirLocalIndex,
dsmonPdistTopNAggGroup,
dsmonPdistTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB."
::= { dsmonGroups 4 }
dsmonPdistHCGroup OBJECT-GROUP
OBJECTS {
dsmonPdistStatsOvflPkts,
dsmonPdistStatsOvflOctets,
dsmonPdistStatsHCPkts,
dsmonPdistStatsHCOctets,
dsmonPdistTopNRateOvfl,
dsmonPdistTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB for High Capacicy
networks."
::= { dsmonGroups 5 }
dsmonHostGroup OBJECT-GROUP
OBJECTS {
dsmonHostControlDataSource,
dsmonHostControlMaxDesiredEntries,
dsmonHostControlNumAddrBits,
dsmonHostControlDroppedFrames,
dsmonHostControlInserts,
dsmonHostControlDeletes,
dsmonHostControlCreateTime,
dsmonHostControlOwner,
dsmonHostControlStatus,
dsmonHostInPkts,
dsmonHostInOctets,
dsmonHostOutPkts,
Expires November 2000 [Page 64]
Internet-Draft DSMON MIB May 2000
dsmonHostOutOctets,
dsmonHostCreateTime,
dsmonHostTopNControlHostIndex,
dsmonHostTopNControlRateBase,
dsmonHostTopNControlTimeRemaining,
dsmonHostTopNControlGeneratedReports,
dsmonHostTopNControlDuration,
dsmonHostTopNControlRequestedSize,
dsmonHostTopNControlGrantedSize,
dsmonHostTopNControlStartTime,
dsmonHostTopNControlOwner,
dsmonHostTopNControlStatus,
dsmonHostTopNAddress,
dsmonHostTopNAggGroup,
dsmonHostTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per IP Host monitoring
functions."
::= { dsmonGroups 6 }
dsmonHostHCGroup OBJECT-GROUP
OBJECTS {
dsmonHostInOvflPkts,
dsmonHostInOvflOctets,
dsmonHostInHCPkts,
dsmonHostInHCOctets,
dsmonHostOutOvflPkts,
dsmonHostOutOvflOctets,
dsmonHostOutHCPkts,
dsmonHostOutHCOctets,
dsmonHostTopNRateOvfl,
dsmonHostTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per IP Host monitoring
functions for High Capacity networks."
::= { dsmonGroups 7 }
END
Expires November 2000 [Page 65]
Internet-Draft DSMON MIB May 2000
7. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to pertain
to the implementation or use of the technology described in this
document or the extent to which any license under such rights might or
might not be available; neither does it represent that it has made any
effort to identify any such rights. Information on the IETF's
procedures with respect to rights in standards-track and standards-
related documentation can be found in BCP-11. Copies of claims of
rights made available for publication and any assurances of licenses to
be made available, or the result of an attempt made to obtain a general
license or permission for the use of such proprietary rights by
implementors or users of this specification can be obtained from the
IETF Secretariat."
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary rights
which may cover technology that may be required to practice this
standard. Please address the information to the IETF Executive
Director.
8. Acknowledgements
This memo has been produced with a great deal of assistance from Keith
McCloghrie and Bijendra Jain.
9. References
[HC-RMON]
S. Waldbusser, "Remote Network Monitoring Management Information
Base for High Capacity Networks", draft-ietf-rmonmib-hcrmon-05.txt,
International Network Services, February 1999.
[RFC1155]
Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
Performance Systems International, Hughes LAN Systems, May 1990.
[RFC1157]
Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, SNMP Research, Performance Systems
International, Performance Systems International, MIT Laboratory
for Computer Science, May 1990.
Expires November 2000 [Page 66]
Internet-Draft DSMON MIB May 2000
[RFC1212]
Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212,
Performance Systems International, Hughes LAN Systems, March 1991.
[RFC1215]
M. Rose, "A Convention for Defining Traps for use with the SNMP",
RFC 1215, Performance Systems International, March 1991.
[RFC1901]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901,
SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting,
Inc., International Network Services, January 1996.
[RFC1905]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Protocol Operations for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1905, SNMP Research,
Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc.,
International Network Services, January 1996.
[RFC1906]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco
Systems, Inc., Dover Beach Consulting, Inc., International Network
Services, January 1996.
[RFC2021]
S. Waldbusser, "Remote Network Monitoring MIB (RMON-2)", RFC 2021,
International Network Services, January 1997.
[RFC2026]
Bradner, S., "The Internet Standards Process -- Revision 3", RFC
2026, Harvard University, October, 1996.
[RFC2074]
Bierman, A., and R. Iddon, "Remote Network Monitoring MIB Protocol
Identifiers", RFC 2074, Cisco Systems, AXON Networks, Inc., January
1997.
[RFC2474]
Nichols, K., Blake, S., Baker, F., and D. L. Black, "Definition of
the Differentiated Services Field (DS Field) in the IPv4 and IPv6
Headers", RFC 2474, Cisco Systems, Torrent Networking Technologies,
Expires November 2000 [Page 67]
Internet-Draft DSMON MIB May 2000
EMC Corporation, December, 1998.
[RFC2475]
Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z., and W.
Weiss, "An Architecture for Differentiated Services", RFC 2475,
Torrent Networking Technologies, EMC Corporation, Sun Microsystems,
Nortel UK, Bell Labs Lucent Technologies, Lucent Technologies,
December, 1998.
[RFC2570]
Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to
Version 3 of the Internet-standard Network Management Framework",
RFC 2570, SNMP Research, Inc., TIS Labs at Network Associates,
Inc., Ericsson, Cisco Systems, April 1999.
[RFC2571]
Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, April
1999.
[RFC2572]
Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, SNMP Research, Inc., Cabletron Systems,
Inc., BMC Software, Inc., IBM T. J. Watson Research, April 1999.
[RFC2573]
Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, SNMP Research, Inc., Secure Computing Corporation, Cisco
Systems, April 1999.
[RFC2574]
Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for
version 3 of the Simple Network Management Protocol (SNMPv3)", RFC
2574, IBM T. J. Watson Research, April 1999.
[RFC2575]
Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, IBM T. J. Watson Research, BMC Software, Inc.,
Cisco Systems, Inc., April 1999.
[RFC2578]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
Expires November 2000 [Page 68]
Internet-Draft DSMON MIB May 2000
and S. Waldbusser, "Structure of Management Information Version 2
(SMIv2)", RFC 2578, STD 58, Cisco Systems, SNMPinfo, TU
Braunschweig, SNMP Research, First Virtual Holdings, International
Network Services, April 1999.
[RFC2579]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Textual Conventions for SMIv2", RFC 2579, STD
58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First
Virtual Holdings, International Network Services, April 1999.
[RFC2580]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Conformance Statements for SMIv2", RFC 2580,
STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research,
First Virtual Holdings, International Network Services, April 1999.
10. Security Considerations
There are a number of management objects defined in this MIB that have a
MAX-ACCESS clause of read-write and/or read-create. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
There are a number of managed objects in this MIB that may contain
sensitive information. These are:
dsmonPdistStatsPkts
dsmonPdistStatsOctets
dsmonPdistStatsHCPkts
dsmonPdistStatsHCOctets
dsmonPdistTopNRate
dsmonPdistTopNHCRate
These objects expose some basic statistics about the DCSP distribution
for each protocol detected on a particular network interface.
dsmonHostInPkts
dsmonHostInOctets
dsmonHostInHCPkts
dsmonHostInHCOctets
dsmonHostOutPkts
Expires November 2000 [Page 69]
Internet-Draft DSMON MIB May 2000
dsmonHostOutOctets
dsmonHostOutHCPkts
dsmonHostOutHCOctets
dsmonHostTopNRate
dsmonHostTopNHCRate
These objects expose some basic statistics about the DCSP distribution
for each IP host detected on a particular network interface.
dsmonHostTopNAddress
This object exposes IP addresses in use on the monitored network
interfaces.
It is thus important to control even GET access to these objects and
possibly to even encrypt the values of these object when sending them
over the network via SNMP. Not all versions of SNMP provide features
for such a secure environment.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and GET/SET
(read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security features
as provided by the SNMPv3 framework. Specifically, the use of the User-
based Security Model RFC 2574 [RFC2574] and the View-based Access
Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity
giving access to an instance of this MIB, is properly configured to give
access to the objects only to those principals (users) that have
legitimate rights to indeed GET or SET (change/create/delete) them.
11. Author's Address
Andy Bierman
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA USA 95134
Phone: +1 408-527-3711
Email: abierman@cisco.com
Expires November 2000 [Page 70]
Internet-Draft DSMON MIB May 2000
12. Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it or
assist in its implementation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are included
on all such copies and derivative works. However, this document itself
may not be modified in any way, such as by removing the copyright notice
or references to the Internet Society or other Internet organizations,
except as needed for the purpose of developing Internet standards in
which case the procedures for copyrights defined in the Internet
Standards process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT
INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE."
Expires November 2000 [Page 71]
