Internet Draft Andy Bierman
Cisco Systems, Inc.
26 October 2001
Remote Monitoring MIB Extensions for
Differentiated Services
<draft-ietf-rmonmib-dsmon-mib-07.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC2026 [RFC2026].
Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups. Note that other groups
may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet- Drafts as reference material
or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Distribution of this document is unlimited. Please send comments to the
RMONMIB WG mailing list <rmonmib@ietf.org>.
1. Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Internet Draft DSMON MIB October 2001
2. Abstract
This memo defines a portion of the Management Information Base (MIB) for
use with network management protocols in the Internet community. In
particular, it describes managed objects used for monitoring
Differentiated Services Codepoint usage in packets which contain a DS
field [RFC2474], utilizing the monitoring framework defined in the
RMON-2 MIB [RFC2021].
3. Table of Contents
1 Copyright Notice ................................................ 1
2 Abstract ........................................................ 2
3 Table of Contents ............................................... 2
4 The SNMP Network Management Framework ........................... 3
5 Overview ........................................................ 4
5.1 Terms ......................................................... 4
5.2 Relationship to Differentiated Services ....................... 5
5.3 Relationship to the Remote Monitoring MIBs .................... 5
6 MIB Structure ................................................... 7
6.1 DSCP Statistical Aggregation .................................. 8
6.1.1 Aggregation Configuration ................................... 9
6.2 MIB Group Overview ............................................ 9
6.2.1 DSCP Aggregation Control Group .............................. 10
6.2.2 DS Statistics Group ......................................... 11
6.2.3 DS Protocol Distribution Group .............................. 11
6.2.4 DS Host Distribution Group .................................. 12
6.2.5 DSMON Capabilities Group .................................... 13
6.2.6 DS Matrix Distribution Group ................................ 13
6.3 RMON vs. DSMON Indexing Structure ............................. 14
7 Definitions ..................................................... 17
8 Aggregation Configuration Usage Examples ........................ 114
8.1 Step 1: Unlock the Aggregation Configuration .................. 114
8.2 Step 2: Check the Maximum number of Aggregation Groups ........ 114
8.3 Step 3: Check if the aggregation profiles already exist ....... 114
8.4 Step 4: Create the Aggregation Control Entries ................ 115
8.5 Step 5: Create the Aggregation Group Descriptions ............. 115
8.6 Step 6: Create the Aggregation Profile Mappings ............... 117
8.7 Step 7: Lock the Aggregation Configuration .................... 121
9 Intellectual Property ........................................... 121
10 Acknowledgements ............................................... 121
11 References ..................................................... 121
12 Security Considerations ........................................ 124
13 Author's Address ............................................... 125
14 Full Copyright Statement ....................................... 126
Expires April 26, 2002 [Page 2]
Internet Draft DSMON MIB October 2001
4. The SNMP Network Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
RFC 1155 [RFC1155], RFC 1212 [RFC1212] and RFC 1215 [RFC1215].
The second version, called SMIv2, is described in RFC 2578
[RFC2578], RFC 2579 [RFC2579] and RFC 2580 [RFC2580].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in RFC 1157 [RFC1157]. A second version of the SNMP
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
and RFC 1906 [RFC1906]. The third version of the message
protocol is called SNMPv3 and described in RFC 1906 [RFC1906],
RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in RFC 1157 [RFC1157]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[RFC1905].
o A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism described
in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
Expires April 26, 2002 [Page 3]
Internet Draft DSMON MIB October 2001
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
5. Overview
There is a need for a standardized way of monitoring the network traffic
usage of Differentiated Services (DS) [RFC2474] codepoint values. Each
DS codepoint (DSCP) value may be given a different treatment by a
forwarding device, and this affects which packets get dropped or delayed
during periods of network congestion.
The IETF DIFFSERV working group has redefined the semantics of the Type
of Service (TOS) octet in the IP header, which is now called the 'DS
field'. The 6-bit Codepoint (DSCP) portion is contained in the DS field,
which provides for 64 different packet treatments for the implementation
of differentiated network services.
By polling DSCP usage counters, an NMS can determine the network
throughput for traffic associated with different DSCPs. This data can
then be analyzed in order to 'tune' DSCP 'allocations' within a network,
based on the Quality of Service (QoS) policies for that network.
Remote monitoring agents are typically implemented as independent
software (and sometimes hardware) components, called 'RMON probes'.
Note that DSMON-capable RMON probes simply collect and aggregate
statistics, based on criteria (which includes the DSCP value) that can
be determined by inspecting the contents of monitored packets. and do
not in any way monitor any aspect of a DS forwarding device's internal
statistics.
5.1. Terms
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119. [RFC2119]
This document uses some terms that need introduction:
DataSource
A source of data for monitoring purposes. This term is used exactly
as defined in the RMON-2 MIB [RFC2021].
Expires April 26, 2002 [Page 4]
Internet Draft DSMON MIB October 2001
protocol
A specific protocol encapsulation, as identified for monitoring
purposes. This term is used exactly as defined in the RMON
Protocol Identifiers document [RFC2074].
Aggregation Group
A group of codepoints that are being counted in the same manner
(i.e., same buckets). Refer to sections 6.1 and 6.2.1 for details
on aggregation groups.
Aggregation Profile
A complete set of aggregation group mappings (i.e. 64 mappings, for
DSCP values 0 to 63), which are applied to all monitored packets on
a particular data source and/or DSMON collection. Refer to
sections 6.1 and 6.2.1 for details on aggregation profiles.
High Capacity Monitoring
The generic capability to collect and store statistics with an
internal range of 64 bits (e.g. Counter64). This term does not
refer to implementation of the High Capacity RMON MIB (HC-RMON).
5.2. Relationship to Differentiated Services
The DSMON MIB is a product of the RMONMIB WG, not the DIFFSERV WG, and
it focuses on extending several existing RMON mechanisms to support
additional packet classification, based on DSCP values observed in
monitored packets. This document assumes the reader is familiar with
the DS Architecture [RFC2475]. It is expected that complex management
applications will use the counters in this MIB to help analyze DS-
related throughput. It is expected that other metrics, such as delay and
jitter, will also be analyzed, but support for other metrics is outside
the scope of this document.
5.3. Relationship to the Remote Monitoring MIBs
This MIB is intended to be implemented in Remote Monitoring (RMON)
probes, which support the RMON-2 MIB [RFC2021]. Such probes may be
stand-alone devices, or may be co-located with other networking devices
(e.g., ethernet switches and repeaters).
The DSMON functions are intended to be implemented in conjunction with
the associated RMON functions, but the MIB is independent of all other
RMON data tables.
Expires April 26, 2002 [Page 5]
Internet Draft DSMON MIB October 2001
Several concepts and even MIB objects from the RMON MIBs are used in the
DSMON MIB:
Protocol Directory
The RMON-2 MIB [RFC2021] defines the protocolDirTable, which is a
directory of all the protocols that the RMON-2 agent is capable of
decoding and counting. The DSMON MIB utilizes this directory to
identify the protocols detected in monitored packets. The
protocolDirLocalIndex MIB object is used to identify protocol
encapsulations in all DSMON data tables which classify and
aggregate by protocol type in some manner. Note that the
protocolDirTable is used for protocol identification only,
independent of DSCP classification.
TimeFilter
The RMON-2 TimeFilter textual convention provides a mechanism to
retrieve only rows which have been created or modified since the
last polling interval (for a particular NMS). The DSMON MIB uses
this textual convention in the large data tables, in order to
minimize polling impact.
Zero-Based Counters
Since counters are instantiated by management action, as in the
RMON MIBs, the DSMON MIB uses zero-based counters in all data
collection tables. Specifically, the ZeroBasedCounter32 textual
convention from the RMON-2 MIB [RFC2021] and the ZeroBasedCounter64
textual convention (defined in the HCNUM-TC MIB [RFC2856]) are used
to define counter objects in this MIB.
High Capacity Counters
The DSMON MIB uses the 'SNMPv1 coexistence' strategy adopted by the
RMONMIB WG. That is, where a 64-bit counter is provided, a 32-bit
version of the counter, and a 32-bit overflow counter are also
provided.
TopN Reports
The DSMON MIB uses the same TopN reporting MIB structure as the
RMON-2 MIB [RFC2021]. TopN reporting can greatly reduce the polling
overhead required to analyze DSCP usage patterns.
Some DESCRIPTION clauses for DSMON objects are very similar to those for
existing RMON-2 or HC-RMON objects. This is intentional, since the
semantics of the DSMON features are designed to be as close to existing
RMON feature as possible, to allow developers and users some level of
'MIB re-use'.
Expires April 26, 2002 [Page 6]
Internet Draft DSMON MIB October 2001
6. MIB Structure
Figure 1: DSMON MIB Functional Structure
+--------------+ +---------------+
| | | |
| DSMON | | Aggregation |
| Capabilities | | Control |
| | | |
+--------------+ +---------------+
|
|
+------------------------------+----------------------------+
| V |
| |
| +-----------+ +-----------+ +-----------+ +------------+ |
| | | | | | | | | |
| | Data Src | | Protocol | | Net. Host | | App Matrix | |
| | Stats | | Stats | | Stats | | Stats | |
| | | | | | | | | |
| +-----------+ +-----------+ +-----------+ +------------+ |
| | | | |
| V V V |
| +-----------+ +-----------+ +------------+ |
| | | | | | | |
| | Protocol | | Net. Host | | App Matrix | |
| | TopN | | TopN | | TopN | |
| | | | | | | |
| +-----------+ +-----------+ +------------+ |
| |
| Data Collection |
| |
+-----------------------------------------------------------+
The DSMON MIB can divided into three functional components:
- DSMON Capabilities
Describes which DSMON object groups are supported by the agent on
at least one data source.
- Aggregation Control
Controls how individual DIFFSERV codepoints are aggregated for
counting purposes in DSMON data collections.
Expires April 26, 2002 [Page 7]
Internet Draft DSMON MIB October 2001
- Data Collection
Controls how individual statistical collections are maintained by
the agent and reported to management applications. The individual
boxes within the Data Collection box represent the DSMON data
collections (described in section 6.2):
- Data Source Statistics
- Protocol Statistics
- Protocol Statistics TopN Reporting
- Network Protocol Host Statistics
- Network Protocol Host Statistics TopN Reporting
- Application Protocol Matrix Statistics
- Application Protocol Matrix Statistics TopN Reporting
6.1. DSCP Statistical Aggregation
A statistical aggregation mechanism is provided, based on DSCP values.
This is desirable for several reasons:
- agent data reduction
An agent implementation can potentially reduce the number of
counters maintained for a given DSMON collection.
- agent data collection limitations
Some implementation strategies might provide for a limited number
of high-speed (e.g. hardware-based) counters for either single or
aggregated codepoints.
- application data retrieval reduction
Applications that would otherwise aggregate counters for individual
codepoints can move that function to the agent in order to reduce
the polling overhead on the application, the network, and the agent
device.
- some unused codepoints at this time
Various DSCP values may be expected to remain unused on a given
network, and may be aggregated for counting purposes.
- some DSCP values are mapped to the same packet treatment
A network administrator may align the aggregation configuration of
the monitoring device with the DS configuration, and aggregate
statistics for DSCP values which are expected to receive the same
treatment by the forwarding devices.
Expires April 26, 2002 [Page 8]
Internet Draft DSMON MIB October 2001
6.1.1. Aggregation Configuration
The configuration of DSCP to aggregation group mappings is managed in a
global manner, so that these settings can be shared across several DSMON
collections and/or data sources. One complete set of DSCP mappings is
called an aggregation profile. The DSMON control tables are very
similar to existing RMON-2 control tables, except they contain an extra
parameter to identify the aggregation profile the agent should use for
the collection.
The appropriate granularity for aggregation profile assignment may be
the data source, but in order to reduce MIB complexity (by avoiding an
extra layer of tables), an instance of the aggregation profile parameter
exists for each collection. An agent MAY choose to restrict
configurations such that all DSMON data collections for the same data
source must use the same aggregation profile.
The DSMON MIB supports the configuration of an arbitrary number of
aggregation profiles. There is a top-level aggregation control table,
which contains one entry for each aggregation profile. A subordinate
aggregation profile table provides information about each DSCP to
aggregation group mapping in each profile. An auxiliary aggregation
group table also provides descriptive information about each aggregation
group in each aggregation profile. Refer to section 6.2.1 for details
on these MIB objects.
6.2. MIB Group Overview
The DSMON MIB contains six groups of MIB objects:
- dsmonAggregateControl group
Controls the configuration of aggregation groups, for the purpose
of reducing the total number of counters maintained by the agent.
- dsmonStatsObjects group
Report per aggregation group distribution statistics for a
particular RMON dataSource.
- dsmonPdistObjects group
Report per aggregation group distribution statistics for each
application protocol detected on a particular RMON dataSource.
- dsmonHostObjects group
Report host address distribution statistics for each aggregation
group, detected on a particular RMON dataSource.
Expires April 26, 2002 [Page 9]
Internet Draft DSMON MIB October 2001
- dsmonCapsObjects group
Report the static DSMON MIB functional capabilities of the agent
implementation.
- dsmonMatrixObjects group
Report host address pair distribution statistics for each
aggregation group, detected on a particular RMON dataSource.
6.2.1. DSCP Aggregation Control Group
This group contains 4 scalar objects and three tables, and is used by a
management station to configure aggregation profiles.
The dsmonMaxAggGroups scalar is a read-only integer which indicates the
maximum number of aggregation groups that the agent will allow to be
configured into a single aggregation profile. This value SHOULD be
equal to 64 (the number of codepoints), but an agent MAY limit the
number of aggregation groups because of resource limitations (e.g.,
small number of hardware-based counters). At least one aggregation
profile containing at least two aggregation groups SHOULD be supported
by the agent. (Note that classifying all DSCP values into the same
statistical 'bucket' may yield a redundant data collection, which can be
achieved more easily with an HC-RMON or RMON-2 collection instead.)
The dsmonAggControlLocked scalar is used as a top level switch,
controlling most write access to the dsmonAggControlTable,
dsmonAggProfileTable, and dsmonAggGroupTable. (The dsmonAggControlOwner
object is the only exception.) All active DSMON collection data is
deleted, and collection suspended, while this object is equal to
'false', since the meaning of one or more aggregation control tables may
change when it is set back to 'true'.
The dsmonAggControlChanges counter and dsmonAggControlLastChangeTime
timestamp can be used by a management station to detect that the
codepoint to aggregation group mappings may have changed between polls.
The dsmonAggControlTable is a read-create table which contains one entry
for each aggregation profile configured on the agent. Each entry is
identified by a dsmonAggControlIndex value, which is also used as the
major index into the dsmonAggProfileTable and dsmonAggGroupTable. The
DSMON control tables with DataSource objects select an aggregation
profile by referencing this index value.
The dsmonAggProfileTable is a read-write table which contains 64 rows
for each associated entry in the dsmonAggControlTable, which MUST be
Expires April 26, 2002 [Page 10]
Internet Draft DSMON MIB October 2001
indexed from 0 to 63. The agent creates this set of 64 instances when
the associated dsmonAggControlEntry is activated, and deletes them when
that dsmonAggControlEntry is deactivated. Each of the 64 rows
represents a DSCP identified by the same dsmonAggProfileDSCP value, and
contains the DSCP to aggregation group mapping for that DSCP, in the
indicated aggregation profile. The agent SHOULD use the value zero as
the initial aggregation group assignment for each entry in this table.
The dsmonAggGroupTable contains an administratively assigned descriptive
label for each configured aggregation group. This table is not required
to be fully configured in order for data collection to occur, since
collections are identified by the agent with integer indices. It is
provided to allow the agent to store a descriptive string for each
configured aggregation group. There is no attempt made to convey any
real semantics for each aggregation group. A management station MAY
choose not to configure entries in this table.
6.2.2. DS Statistics Group
This group contains two tables, the dsmonStatsControlTable and the
dsmonStatsTable, and supports aggregation group distribution statistics
for half and full-duplex, low and high speed interfaces. Packet and
octets distributions are maintained in the dsmonStatsTable for each
active control row in the dsmonStatsControlTable.
This group provides the lowest statistics granularity in the DSMON MIB.
It is expected that a management application will analyze certain DS
deployment or performance problems by first examining the aggregation
group distribution for an entire data source with this group.
6.2.3. DS Protocol Distribution Group
This group contains two tables for statistics collection,
(dsmonPdistCtlTable and dsmonPdistStatsTable), and two tables for a 'Top
N' reporting function for the collected statistics
(dsmonPdistTopNCtlTable and dsmonPdistTopNTable).
The dsmonPdistCtlTable and dsmonPdistStatsTable tables provide
aggregation group distribution statistics for each selected protocol
encapsulation in packets monitored on a particular dataSource. Packet
and octets distributions (per aggregation group per protocol) are
maintained in the dsmonPdistStatsTable for each active control row in
the dsmonPdistCtlTable.
Expires April 26, 2002 [Page 11]
Internet Draft DSMON MIB October 2001
Due the potentially large number of entries, the DS Protocol
Distribution is different from the RMON-2 protocol distribution group in
several ways:
- maximum desired entries parameter added to the control table
- inserts and deletes counters added to the control table
- support for LRU garbage collection in the dsmonPdistStatsTable
- TimeFilter index added to the dsmonPdistStatsTable
- the selection of protocols is not configurable. Rather than select
individual protocols to monitor, (e.g., via a 'supportedOn/Off'
extension to the protocolDirTable [RFC 2021]), a simplified
configuration mechanism is provided. Since DSCP usage statistics
are most interesting at the application layer, the
dsmonPdistStatsTable is 'hardwired' to select only application
layer (i.e., 'terminal') protocols for statistical analysis.
The TopN feature requires two additional tables: the
dsmonPdistTopNCtlTable and the dsmonPdistTopNTable, and supports
periodic usage reporting for the statistics maintained in the
dsmonPdistStatsTable. This feature allows for simple periodic retrieval
of the most used application/aggregation group combinations.
6.2.4. DS Host Distribution Group
This group contains two tables for statistics collection,
(dsmonHostCtlTable and dsmonHostTable), and two tables for a 'Top N'
reporting function for the collected statistics (dsmonHostTopNCtlTable
and dsmonHostTopNTable).
The dsmonHostCtlTable and dsmonHostTables provide host distribution
statistics for each aggregation group detected in packets monitored on a
particular dataSource. The DSMON Host collection is similar to the
RMON-2 network layer host collection (nlHostTable). There is no DSMON
application host table defined at this time.
It is expected that a management application will analyze certain DS
deployment or performance problems by first determining the high
priority DSCP values to examine (beyond the scope of this document) and
then examining the dsmonHostTable or dsmonHostTopNTable statistics to
determine which hosts are using the selected aggregation groups.
Expires April 26, 2002 [Page 12]
Internet Draft DSMON MIB October 2001
Packet and octets distributions (in and out, per aggregation group per
host) are maintained in the dsmonHostTable for each active control row
in the dsmonHostCtlTable.
The DS Host Distribution is different from the RMON-2 network layer host
group in two ways:
- the protocolDirLocalIndex in the INDEX clause MUST identify a
network protocol encapsulation which contains a DS field (e.g.,
IPv4 or IPv6). If a protocol encapsulation with multiple network
layers is specified, then associated entries in this table refer to
the innermost network protocol layer.
- the dsmonHostCtlTable supports limited IPv4 and IPv6 prefix
aggregation by allowing the number of 'monitored address bits' in
each address to be configured for each collection. The agent will
zero out the selected number of rightmost address bits for counting
purposes. This configuration parameter can dramatically reduce the
number of entries which must be maintained by the agent, which
should reduce CPU and memory resource requirements on the agent,
and reduce polling overhead on the network and the management
station. However, only one mask can be configured for each address
type, rather than multiple different length masks for each address
type, based on prefix value.
The TopN feature requires two additional tables: the
dsmonHostTopNCtlTable and the dsmonHostTopNTable. and supports periodic
usage reporting for the statistics maintained in the dsmonHostTable.
This feature allows for simple periodic retrieval of the most used IP-
host/DSCP combinations.
6.2.5. DSMON Capabilities Group
This group contains a single read-only scalar object, dsmonCapabilities,
which provides an indication the MIB groups within this MIB that the
agent supports.
6.2.6. DS Matrix Distribution Group
This group contains three tables for statistics collection,
(dsmonMatrixCtlTable, dsmonMatrixSDTable, and dsmonMatrixDSTable), and
two tables for a 'Top N' reporting function for the collected statistics
(dsmonMatrixTopNCtlTable and dsmonMatrixTopNTable).
The dsmonMatrixCtlTable, dsmonMatrixSDTable, and dsmonMatrixDSTable
Expires April 26, 2002 [Page 13]
Internet Draft DSMON MIB October 2001
provide host-pair distribution statistics for each aggregation group
detected in packets monitored on a particular dataSource. The DSMON
Matrix collection is similar to the RMON-2 application layer matrix
collection (alMatrixSDTable and alMatrixDSTable). There is no DSMON
network layer matrix table defined at this time.
It is expected that a management application will analyze certain DS
deployment or performance problems by first determining the high
priority DSCP values to examine (beyond the scope of this document) and
then examining the dsmonMatrixSDTable, dsmonMatrixDSTable, and/or
dsmonMatrixTopNTable statistics to determine which host-pairs are using
the selected aggregation groups.
Packet and octets distributions (source to destination, per aggregation
group per host-pair) are maintained in the dsmonMatrixSDTable and
dsmonMatrixDSTable for each active control row in the
dsmonMatrixCtlTable.
The TopN feature requires two additional tables: the
dsmonMatrixTopNCtlTable and the dsmonMatrixTopNTable. and supports
periodic usage reporting for the statistics maintained in the
dsmonMatrixSDTable. This feature allows for simple periodic retrieval
of the most used IP-host-pair/DSCP combinations.
6.3. RMON vs. DSMON Indexing Structure
The DSMON-MIB control and data tables are very similar in structure and
look-and-feel to existing RMON-2 and HC-RMON control tables for the
comparable feature, in order to maintain consistent agent behavior and
functionality across RMON MIBs. The DSMON data tables are indexed as
closely as possible to the comparable RMON-2 or HC-RMON tables, with the
addition of an index component for DSCP-based classification (i.e.
dsmonAggGroup). Refer to Table 1 for a comparison of DSMON indexing
structure with similar existing RMON features.
Expires April 26, 2002 [Page 14]
Internet Draft DSMON MIB October 2001
Table 1: DSMON Indexing Comparison
Existing RMON DSMON
--------------------------------------------------------------------
Full Duplex Interface Statistics
mediaIndependentEntry | dsmonStatsControlEntry
mediaIndependentIndex | dsmonStatsControlIndex
| dsmonStatsEntry
| dsmonStatsControlIndex,
| dsmonAggGroupIndex
---------------------------------+------------------------------
Protocol Statistics
protocolDistControlEntry | dsmonPdistCtlEntry
protocolDistControlIndex | dsmonPdistCtlIndex
protocolDistStatsEntry | dsmonPdistStatsEntry
protocolDistControlIndex, | dsmonPdistCtlIndex,
protocolDirLocalIndex | dsmonPdistTimeMark,
| dsmonAggGroupIndex,
| protocolDirLocalIndex
---------------------------------+--------------------------------
Protocol TopN Distribution
| dsmonPdistTopNCtlEntry
| dsmonPdistTopNCtlIndex
none | dsmonPdistTopNEntry
| dsmonPdistTopNCtlIndex,
| dsmonPdistTopNIndex
---------------------------------+--------------------------------
Network Host Statistics
hlHostControlEntry | dsmonHostCtlEntry
hlHostControlIndex | dsmonHostCtlIndex
nlHostEntry | dsmonHostEntry
hlHostControlIndex, | dsmonHostCtlIndex,
nlHostTimeMark, | dsmonHostTimeMark,
protocolDirLocalIndex, | dsmonAggGroupIndex,
nlHostAddress | protocolDirLocalIndex,
| dsmonHostAddress
---------------------------------+--------------------------------
Expires April 26, 2002 [Page 15]
Internet Draft DSMON MIB October 2001
Table 1 (Continued): DSMON Indexing Comparison
Existing RMON DSMON
---------------------------------+--------------------------------
Network Host TopN Distribution
| dsmonHostTopNCtlEntry
| dsmonHostTopNCtlIndex
none | dsmonHostTopNEntry
| dsmonHostTopNCtlIndex,
| dsmonHostTopNIndex
---------------------------------+--------------------------------
Application Matrix Statistics
hlMatrixControlEntry | dsmonMatrixCtlEntry
hlMatrixControlIndex | dsmonMatrixCtlIndex
alMatrixSDEntry | dsmonMatrixSDEntry
hlMatrixControlIndex, | dsmonMatrixCtlIndex,
alMatrixSDTimeMark, | dsmonMatrixTimeMark,
protocolDirLocalIndex, | dsmonAggGroupIndex,
nlMatrixSDSourceAddress, | dsmonMatrixNLIndex,
nlMatrixSDDestAddress | dsmonMatrixSourceAddress
protocolDirLocalIndex | dsmonMatrixDestAddress
| dsmonMatrixALIndex
alMatrixDSEntry | dsmonMatrixDSEntry
hlMatrixControlIndex, | dsmonMatrixCtlIndex,
alMatrixDSTimeMark, | dsmonMatrixTimeMark,
protocolDirLocalIndex, | dsmonAggGroupIndex,
nlMatrixDSDestAddress, | dsmonMatrixNLIndex,
nlMatrixDSSourceAddress | dsmonMatrixDestAddress
protocolDirLocalIndex | dsmonMatrixSourceAddress
| dsmonMatrixALIndex
---------------------------------+--------------------------------
Application Matrix TopN Distribution
| dsmonMatrixTopNCtlEntry
none | dsmonMatrixTopNCtlIndex
| dsmonMatrixTopNEntry
(similar to nlMatrixTopN) | dsmonMatrixTopNCtlIndex,
| dsmonMatrixTopNIndex
---------------------------------+--------------------------------
Expires April 26, 2002 [Page 16]
Internet Draft DSMON MIB October 2001
7. Definitions
DSMON-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32,
Counter32, Gauge32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, TimeStamp, TEXTUAL-CONVENTION, TruthValue
FROM SNMPv2-TC
OwnerString, rmon
FROM RMON-MIB
protocolDirLocalIndex, LastCreateTime,
DataSource, ZeroBasedCounter32, TimeFilter
FROM RMON2-MIB
CounterBasedGauge64, ZeroBasedCounter64
FROM HCNUM-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
Dscp
FROM DIFFSERV-DSCP-TC;
dsmonMIB MODULE-IDENTITY
LAST-UPDATED "200110260000Z"
ORGANIZATION "IETF RMONMIB Working Group"
CONTACT-INFO
" Andy Bierman
Cisco Systems, Inc.
RMONMIB WG Chair and DSMON MIB Editor
Postal: 170 West Tasman Drive
San Jose, CA USA 95134
Tel: +1 408 527-3711
E-mail: abierman@cisco.com
Send comments to <rmonmib@ietf.org>
Mailing list subscription info:
http://www.ietf.org/mailman/listinfo/rmonmib "
DESCRIPTION
"This module defines Remote Monitoring MIB extensions for
Differentiated Services enabled networks.
RMON DIFFSERV DSCP statistics
Expires April 26, 2002 [Page 17]
Internet Draft DSMON MIB October 2001
* Per Aggregation Group
* Per Protocol Per Aggregation Group
* Per Aggregation Group Per Host
* Per Aggregation Group Per Host-Pair
In order to maintain the RMON 'look-and-feel' and semantic
consistency, some of the text from the RMON-2 and HC-RMON
MIBs by Steve Waldbusser has been adapted for use in this
MIB."
REVISION "200110260000Z"
DESCRIPTION
"Initial version of the DSMON MIB module. This version
published as RFC xxxx (to be assigned by the RFC Editor)."
::= { rmon 26 }
dsmonObjects OBJECT IDENTIFIER ::= { dsmonMIB 1 }
dsmonNotifications OBJECT IDENTIFIER ::= { dsmonMIB 2 }
dsmonConformance OBJECT IDENTIFIER ::= { dsmonMIB 3 }
dsmonAggObjects OBJECT IDENTIFIER ::= { dsmonObjects 1 }
dsmonStatsObjects OBJECT IDENTIFIER ::= { dsmonObjects 2 }
dsmonPdistObjects OBJECT IDENTIFIER ::= { dsmonObjects 3 }
dsmonHostObjects OBJECT IDENTIFIER ::= { dsmonObjects 4 }
dsmonCapsObjects OBJECT IDENTIFIER ::= { dsmonObjects 5 }
dsmonMatrixObjects OBJECT IDENTIFIER ::= { dsmonObjects 6 }
--
-- Textual Convention to define a
-- DSMON Aggregation Group Index
--
DsmonAggGroupIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes a data type which identifies a DSMON
aggregation group, which is an arbitrary grouping of DSCP
values, for monitoring purposes only. The range for this
data type begins with zero (instead of one), to allow for a
direct mapping between DSCP and aggregation group values."
SYNTAX Integer32 (0..2147483647)
--
-- Textual Convention to define a
-- DSMON Aggregation Profile Index
Expires April 26, 2002 [Page 18]
Internet Draft DSMON MIB October 2001
--
DsmonAggProfileIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes a data type which identifies a DSMON
aggregation profile, which is a set of aggregation group
assignments for each of the 64 DSCP values, for a particular
statistical collection."
SYNTAX Integer32 (1..2147483647)
-- ***********************************************************
-- * *
-- * D S M O N C A P A B I L I T I E S *
-- * *
-- ***********************************************************
dsmonCapabilities OBJECT-TYPE
SYNTAX BITS {
dsmonAggControl(0),
dsmonStats(1),
dsmonStatsOvfl(2),
dsmonStatsHC(3),
dsmonPdist(4),
dsmonPdistOvfl(5),
dsmonPdistHC(6),
dsmonHost(7),
dsmonHostOvfl(8),
dsmonHostHC(9),
dsmonCaps(10),
dsmonMatrix(11),
dsmonMatrixOvfl(12),
dsmonMatrixHC(13)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object provides an indication of the DSMON groups
supported by the agent. If a bit is set, then the agent
implements all of the objects in the DSMON object group,
where bit 'n' represents the MIB group identified by the
OBJECT IDENTIFIER value { dsmonGroups n+1 }."
::= { dsmonCapsObjects 1 }
Expires April 26, 2002 [Page 19]
Internet Draft DSMON MIB October 2001
-- ***********************************************************
-- * *
-- * A G G R E G A T I O N C O N T R O L G R O U P S *
-- * *
-- ***********************************************************
dsmonMaxAggGroups OBJECT-TYPE
SYNTAX Integer32 (2..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of aggregation groups that this agent
can support. The agent will allow this number of distinct
groups to be configured in the dsmonAggProfileTable,
numbered from '0' to 'dsmonMaxAggGroups - 1', for each
aggregation profile entry supported by the agent.
The agent MUST NOT lower this value during system operation,
and SHOULD set this object to an appropriate value during
system initialization."
::= { dsmonAggObjects 1 }
dsmonAggControlLocked OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the setup of aggregation groups for this agent.
If this object contains the value 'true', then write access
to the objects in the dsmonAggControlTable (except the
dsmonAggControlOwner object), dsmonAggProfileTable, and
dsmonAggGroupTable is not permitted, and data collection is
possible. This object only controls write access to these
MIB objects. The DSMON data collection control tables (e.g.,
dsmonHostCtlTable) can be configured at any time, regardless
of the value of this object.
If this object contains the value 'false', write access to
the objects in the dsmonAggControlTable,
dsmonAggProfileTable, and dsmonAggGroupTable is permitted,
and data collection is not possible. In addition, all
objects in all DSMON data tables (e.g., dsmonStatsTable)
shall be deleted.
Expires April 26, 2002 [Page 20]
Internet Draft DSMON MIB October 2001
An agent is not required to process SNMP Set Requests for
this object in conjunction with other objects from this MIB.
This is intended to simplify the processing of Set Requests
for tables such as the dsmonAggProfileTable, by eliminating
the possibility that a single Set PDU will contain multiple
varbinds which are in conflict, such as a PDU which both
modifies the dsmonAggProfileTable and locks the
dsmonAggProfileTable at the same time.
Note that the agent is not required to validate the entire
aggregation configuration when an attempt is made to
transition an instance of this object from 'true' to
'false'. That validation is done if and when a DSMON data
collection is activated.
An agent is required to reactivate any suspended data
collections when this object transitions to 'true', Each
active data control entry (e.g., dsmonStatsControlEntry),
will be validated with respect to the new aggregation
configuration. If the aggregation profile referenced in the
data collection is valid, then that collection will be
restarted. Otherwise, the RowStatus object (e.g.,
dsmonStatsControlStatus) will be set to 'notReady' for that
collection control entry."
::= { dsmonAggObjects 2 }
dsmonAggControlChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times the value of the
dsmonAggControlLocked object has changed. A management
station can use this object to detect if counters in the
DSMON data tables (e.g., dsmonStatsEntry) have been deleted
and recreated between polls.
This object shall be incremented by one each time the
dsmonAggControlLocked object changes from 'false' to 'true',
or from 'true' to 'false'."
::= { dsmonAggObjects 3 }
dsmonAggControlLastChangeTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
Expires April 26, 2002 [Page 21]
Internet Draft DSMON MIB October 2001
STATUS current
DESCRIPTION
"This object identifies the value of sysUpTime at the moment
the dsmonAggControlLocked object was last modified. A
management station can use this object to detect if counters
in the DSMON data tables (e.g., dsmonStatsEntry) have been
deleted and recreated between polls.
This object shall be updated with the current value of
sysUpTime, if the dsmonAggControlLocked object changes from
'false' to 'true', or from 'true' to 'false'.
Upon system initialization, this object shall contain the
value zero."
::= { dsmonAggObjects 4 }
--
-- Aggregation Control Table
--
dsmonAggControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides an overall description and control
point for all dsmonAggProfileEntries with the same
dsmonAggControlIndex value.
A management application SHOULD create an aggregation
profile by first creating and activating an entry in this
table. This will cause the agent to create a set of 64
dsmonAggProfileEntries on behalf of this control entry. An
application can then set the individual aggregation group
assignments for each of the 64 DSCP values,
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table, and
(independently) the number of aggregation profiles which may
be applied to a particular data source. In this case, the
agent SHOULD return an error-status of
Expires April 26, 2002 [Page 22]
Internet Draft DSMON MIB October 2001
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905].
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values. Otherwise, each
potential aggregation group description string SHOULD
contain the empty string."
::= { dsmonAggObjects 5 }
dsmonAggControlEntry OBJECT-TYPE
SYNTAX DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggControlTable."
INDEX { dsmonAggControlIndex }
::= { dsmonAggControlTable 1 }
DsmonAggControlEntry ::= SEQUENCE {
dsmonAggControlIndex DsmonAggProfileIndex,
dsmonAggControlDescr SnmpAdminString,
dsmonAggControlOwner OwnerString,
dsmonAggControlStatus RowStatus
}
dsmonAggControlIndex OBJECT-TYPE
SYNTAX DsmonAggProfileIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer index value used to identify the
aggregation profile specified by this control entry."
::= { dsmonAggControlEntry 1 }
dsmonAggControlDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned description of the aggregation
profile identified by this entry.
Upon first creation of an instance of this object, the agent
SHOULD set this object to the empty string. If the agent
Expires April 26, 2002 [Page 23]
Internet Draft DSMON MIB October 2001
supports non-volatile storage, then this object SHOULD be
re-initialized with its stored value after a system reboot.
This object MUST NOT be modified if the associated
dsmonAggControlStatus object is equal to 'active', or the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggControlEntry 2 }
dsmonAggControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonAggControlEntry 3 }
dsmonAggControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
Upon setting this object to active(1), the agent will create
a complete set of 64 associated entries in the
dsmonAggProfileTable.
If this object is not equal to active(1), all associated
entries in the dsmonAggProfileTable shall be deleted.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggControlEntry 4 }
--
-- Aggregation Profile Table
--
dsmonAggProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggProfileEntry
Expires April 26, 2002 [Page 24]
Internet Draft DSMON MIB October 2001
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of aggregation profiles for this agent.
For each such profile, every DSCP value MUST be configured
into exactly one aggregation group.
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
The agent will create a set of 64 entries in this table
(with the same dsmonAggControlIndex value) when the
associated dsmonAggControlEntry is activated.
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table SHOULD be
initialized with the saved values."
::= { dsmonAggObjects 6 }
dsmonAggProfileEntry OBJECT-TYPE
SYNTAX DsmonAggProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggProfileTable. The
dsmonAggControlIndex value in the index identifies the
dsmonAggControlEntry associated with each entry in this
table."
INDEX { dsmonAggControlIndex, dsmonAggProfileDSCP }
::= { dsmonAggProfileTable 1 }
DsmonAggProfileEntry ::= SEQUENCE {
dsmonAggProfileDSCP Dscp,
dsmonAggGroupIndex DsmonAggGroupIndex
}
dsmonAggProfileDSCP OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The specific DSCP value which is configured in an
aggregation group by this entry."
::= { dsmonAggProfileEntry 1 }
Expires April 26, 2002 [Page 25]
Internet Draft DSMON MIB October 2001
dsmonAggGroupIndex OBJECT-TYPE
SYNTAX DsmonAggGroupIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The aggregation group which contains this DSCP value. Upon
creation of a new sub-tree (set of 64 entries with the same
dsmonAggControlIndex value) in this table, the agent SHOULD
initialize all related instances of this object to the value
zero.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
DEFVAL { 0 }
::= { dsmonAggProfileEntry 2 }
--
-- Aggregation Group Table
--
dsmonAggGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides a description of each aggregation group
configured on this system. Note that the semantics of a
particular aggregation group are only relevant within the
scope of a particular aggregation profile.
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table, and
(independently) the number of aggregation profiles which may
be applied to a particular data source. In this case, the
agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905].
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table SHOULD be
initialized with the saved values. Otherwise, each
Expires April 26, 2002 [Page 26]
Internet Draft DSMON MIB October 2001
potential aggregation group description string SHOULD
contain the empty string.
An agent SHOULD allow entries to be created or modified in
this table, even if the specified dsmonAggControlIndex value
does not identify a valid dsmonAggControlEntry or a complete
set of valid dsmonAggProfileEntries, to reduce row creation
order dependencies."
::= { dsmonAggObjects 7 }
dsmonAggGroupEntry OBJECT-TYPE
SYNTAX DsmonAggGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggGroupTable. The
dsmonAggGroupIndex value in the INDEX identifies the
aggregation group associated with each entry.
The dsmonAggControlIndex in the index identifies the
aggregation profile associated with each entry, identified
by the dsmonAggControlEntry and dsmonAggProfileEntries with
the same index value.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
The dsmonAggGroupIndex in the index identifies the
aggregation group associated with each entry. This object
SHOULD be indexed from zero to 'N', where 'N' is less than
the value of the dsmonMaxAggGroups for this agent."
INDEX { dsmonAggControlIndex, dsmonAggGroupIndex }
::= { dsmonAggGroupTable 1 }
DsmonAggGroupEntry ::= SEQUENCE {
dsmonAggGroupDescr SnmpAdminString,
dsmonAggGroupStatus RowStatus
}
dsmonAggGroupDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..64))
MAX-ACCESS read-create
STATUS current
Expires April 26, 2002 [Page 27]
Internet Draft DSMON MIB October 2001
DESCRIPTION
"An administratively assigned description of the aggregation
group identified by this entry.
Upon first creation of an instance of this object, the agent
SHOULD set this object to the empty string.
This object MUST NOT be modified if the associated
dsmonAggGroupStatus object is equal to 'active', or the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggGroupEntry 1 }
dsmonAggGroupStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggGroupEntry 2 }
-- *************************************************************
-- * *
-- * P E R - D A T A S O U R C E C O L L E C T I O N S *
-- * *
-- *************************************************************
--
-- Per-DataSource Statistics Control Table
--
dsmonStatsControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per data source per aggregation group
distribution statistics.
Expires April 26, 2002 [Page 28]
Internet Draft DSMON MIB October 2001
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonStatsObjects 1 }
dsmonStatsControlEntry OBJECT-TYPE
SYNTAX DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonStatsControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonStatsControlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonStatsTable to be created and maintained by
the agent."
INDEX { dsmonStatsControlIndex }
::= { dsmonStatsControlTable 1 }
DsmonStatsControlEntry ::= SEQUENCE {
dsmonStatsControlIndex Integer32,
dsmonStatsControlDataSource DataSource,
dsmonStatsControlAggProfile DsmonAggProfileIndex,
dsmonStatsControlDroppedFrames Counter32,
dsmonStatsControlCreateTime LastCreateTime,
dsmonStatsControlOwner OwnerString,
dsmonStatsControlStatus RowStatus
}
dsmonStatsControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonStatsControlEntry."
Expires April 26, 2002 [Page 29]
Internet Draft DSMON MIB October 2001
::= { dsmonStatsControlEntry 1 }
dsmonStatsControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The data source of this per protocol per aggregation group
distribution.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 2 }
dsmonStatsControlAggProfile OBJECT-TYPE
SYNTAX DsmonAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonStatsControlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonStats collection. In this case, the
associated dsmonStatsControlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 3 }
Expires April 26, 2002 [Page 30]
Internet Draft DSMON MIB October 2001
dsmonStatsControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonStatsControlEntry 4 }
dsmonStatsControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonStatsControlEntry 5 }
dsmonStatsControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonStatsControlEntry 6 }
dsmonStatsControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires April 26, 2002 [Page 31]
Internet Draft DSMON MIB October 2001
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonStatsTable shall be deleted."
::= { dsmonStatsControlEntry 7 }
--
-- Per-DataSource Statistics Table
--
dsmonStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on aggregation group usage for each
monitored data source.
The following table defines per aggregation group statistics
for full and/or half-duplex links as well as high capacity
links.
For half-duplex links, or full-duplex-capable links
operating in half-duplex mode, the dsmonStatsIn* objects
shall be used and the dsmonStatsOut* objects will not
increment.
For full-duplex links, the dsmonStatsOut* objects will be
present. Whenever possible, the probe SHOULD count packets
moving away from the closest terminating equipment as output
packets. Failing that, the probe SHOULD count packets moving
away from the DTE as output packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted and the agent
will not process packets on behalf of any
dsmonStatsControlEntry."
::= { dsmonStatsObjects 2 }
dsmonStatsEntry OBJECT-TYPE
SYNTAX DsmonStatsEntry
MAX-ACCESS not-accessible
Expires April 26, 2002 [Page 32]
Internet Draft DSMON MIB October 2001
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing inbound and outbound packet and octet
counters for each aggregation group configured for
collection.
The dsmonStatsControlIndex value in the index identifies the
dsmonStatsControlEntry on whose behalf this entry was
created.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry for that DSCP value.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
An example of the indexing of this entry is
dsmonStatsOutPkts.1.16"
INDEX { dsmonStatsControlIndex, dsmonAggGroupIndex }
::= { dsmonStatsTable 1 }
DsmonStatsEntry ::= SEQUENCE {
dsmonStatsInPkts ZeroBasedCounter32,
dsmonStatsInOctets ZeroBasedCounter32,
dsmonStatsInOvflPkts ZeroBasedCounter32,
dsmonStatsInOvflOctets ZeroBasedCounter32,
dsmonStatsInHCPkts ZeroBasedCounter64,
dsmonStatsInHCOctets ZeroBasedCounter64,
dsmonStatsOutPkts ZeroBasedCounter32,
dsmonStatsOutOctets ZeroBasedCounter32,
dsmonStatsOutOvflPkts ZeroBasedCounter32,
dsmonStatsOutOvflOctets ZeroBasedCounter32,
dsmonStatsOutHCPkts ZeroBasedCounter64,
dsmonStatsOutHCOctets ZeroBasedCounter64
}
dsmonStatsInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires April 26, 2002 [Page 33]
Internet Draft DSMON MIB October 2001
"The number of packets using one of the DSCP values in the
indicated aggregation group, received on a half-duplex link
or on the inbound connection of a full-duplex link."
::= { dsmonStatsEntry 1 }
dsmonStatsInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, received on a
half-duplex link or on the inbound connection of a full-
duplex link."
::= { dsmonStatsEntry 2 }
dsmonStatsInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 3 }
dsmonStatsInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 4 }
dsmonStatsInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires April 26, 2002 [Page 34]
Internet Draft DSMON MIB October 2001
"The 64-bit version of the dsmonStatsInPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 5 }
dsmonStatsInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 6 }
dsmonStatsOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated aggregation group, received on a full-duplex link
in the direction of the network."
::= { dsmonStatsEntry 7 }
dsmonStatsOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, received on a
full-duplex link in the direction of the network."
::= { dsmonStatsEntry 8 }
dsmonStatsOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
Expires April 26, 2002 [Page 35]
Internet Draft DSMON MIB October 2001
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsOutPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 9 }
dsmonStatsOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 10 }
dsmonStatsOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 11 }
dsmonStatsOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonStatsEntry 12 }
Expires April 26, 2002 [Page 36]
Internet Draft DSMON MIB October 2001
-- ***********************************************************
-- * *
-- * P E R - P R O T O C O L C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- DSCP Per-Protocol Statistics Control Table
--
dsmonPdistCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per application per aggregation group
distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonPdistObjects 1 }
dsmonPdistCtlEntry OBJECT-TYPE
SYNTAX DsmonPdistCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonPdistCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonPdistStatsTable to be created and maintained
by the agent."
INDEX { dsmonPdistCtlIndex }
::= { dsmonPdistCtlTable 1 }
Expires April 26, 2002 [Page 37]
Internet Draft DSMON MIB October 2001
DsmonPdistCtlEntry ::= SEQUENCE {
dsmonPdistCtlIndex Integer32,
dsmonPdistCtlDataSource DataSource,
dsmonPdistCtlAggProfile DsmonAggProfileIndex,
dsmonPdistCtlMaxDesiredEntries Integer32,
dsmonPdistCtlDroppedFrames Counter32,
dsmonPdistCtlInserts Counter32,
dsmonPdistCtlDeletes Counter32,
dsmonPdistCtlCreateTime LastCreateTime,
dsmonPdistCtlOwner OwnerString,
dsmonPdistCtlStatus RowStatus
}
dsmonPdistCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this dsmonPdistCtlEntry."
::= { dsmonPdistCtlEntry 1 }
dsmonPdistCtlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the this per protocol aggregation
group distribution.
This object MUST NOT be modified if the associated
dsmonPdistCtlStatus object is equal to active(1)."
::= { dsmonPdistCtlEntry 2 }
dsmonPdistCtlAggProfile OBJECT-TYPE
SYNTAX DsmonAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonPdistCtlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
Expires April 26, 2002 [Page 38]
Internet Draft DSMON MIB October 2001
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonPdist collection. In this case, the
associated dsmonPdistCtlStatus object will be changed to the
'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonPdistCtlStatus object is equal to active(1)."
::= { dsmonPdistCtlEntry 3 }
dsmonPdistCtlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonPdistStatsTable on behalf of this control entry. The
probe will not create more than this number of associated
entries in the table, but MAY choose to create fewer entries
in this table for any reason including the lack of
resources.
If this value is set to -1, the probe MAY create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonPdistCtlStatus object is equal to active(1)."
::= { dsmonPdistCtlEntry 4 }
dsmonPdistCtlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
Expires April 26, 2002 [Page 39]
Internet Draft DSMON MIB October 2001
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonPdistCtlEntry 5 }
dsmonPdistCtlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been inserted
into the dsmonPdistTable. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistCtlDeletes from dsmonPdistCtlInserts."
::= { dsmonPdistCtlEntry 6 }
dsmonPdistCtlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been deleted
from the dsmonPdist table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
Expires April 26, 2002 [Page 40]
Internet Draft DSMON MIB October 2001
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistCtlDeletes from dsmonPdistCtlInserts."
::= { dsmonPdistCtlEntry 7 }
dsmonPdistCtlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonPdistCtlEntry 8 }
dsmonPdistCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistCtlEntry 9 }
dsmonPdistCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistStatsTable shall be deleted."
::= { dsmonPdistCtlEntry 10 }
--
-- Per-Protocol Statistics Table
--
Expires April 26, 2002 [Page 41]
Internet Draft DSMON MIB October 2001
dsmonPdistStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on a per protocol per aggregation
group usage.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted and the agent
will not process packets on behalf of any
dsmonPdistCtlEntry."
::= { dsmonPdistObjects 2 }
dsmonPdistStatsEntry OBJECT-TYPE
SYNTAX DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each
aggregation group configured for collection, and each
protocol (as identified by the protocolDirLocalIndex for the
protocol) identified in each monitored packet.
The dsmonPdistCtlIndex value in the index identifies the
dsmonPdistCtlEntry on whose behalf this entry was created.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry for that value.
The protocolDirLocalIndex in the index identifies the
protocolDirEntry for the protocol encapsulation of each
monitored packet. The agent will include only application
layer protocols in the associated dsmonPdistStatsTable. Any
'terminal' protocol is considered to be an application
protocol.
An example of the indexing of this entry is
dsmonPdistStatsPkts.9.29943.0.42."
Expires April 26, 2002 [Page 42]
Internet Draft DSMON MIB October 2001
INDEX { dsmonPdistCtlIndex,
dsmonPdistTimeMark,
dsmonAggGroupIndex,
protocolDirLocalIndex }
::= { dsmonPdistStatsTable 1 }
DsmonPdistStatsEntry ::= SEQUENCE {
dsmonPdistTimeMark TimeFilter,
dsmonPdistStatsPkts ZeroBasedCounter32,
dsmonPdistStatsOctets ZeroBasedCounter32,
dsmonPdistStatsOvflPkts ZeroBasedCounter32,
dsmonPdistStatsOvflOctets ZeroBasedCounter32,
dsmonPdistStatsHCPkts ZeroBasedCounter64,
dsmonPdistStatsHCOctets ZeroBasedCounter64,
dsmonPdistStatsCreateTime LastCreateTime
}
dsmonPdistTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonPdistStatsEntry 1 }
dsmonPdistStatsPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets, using one of the DSCP values in the
indicated aggregation group, for the protocol identified by
the associated protocolDirLocalIndex value."
::= { dsmonPdistStatsEntry 2 }
dsmonPdistStatsOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
Expires April 26, 2002 [Page 43]
Internet Draft DSMON MIB October 2001
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, for the protocol
identified by the associated protocolDirLocalIndex value.
Note that this object doesn't count just those octets in the
particular protocol frames, but includes the entire packet
that contained the protocol."
::= { dsmonPdistStatsEntry 3 }
dsmonPdistStatsOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonPdistStatsPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCPkts object
is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 4 }
dsmonPdistStatsOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonPdistStatsOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCOctets
object is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 5 }
dsmonPdistStatsHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
Expires April 26, 2002 [Page 44]
Internet Draft DSMON MIB October 2001
::= { dsmonPdistStatsEntry 6 }
dsmonPdistStatsHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonPdistStatsEntry 7 }
dsmonPdistStatsCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonPdistStats entry was
last instantiated by the agent. This can be used by the
management station to detect if the entry has been deleted
and recreated between polls."
::= { dsmonPdistStatsEntry 8 }
--
-- Per-Protocol Statistics TopN Control Table
--
dsmonPdistTopNCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonPdist entries according to a particular
metric.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
Expires April 26, 2002 [Page 45]
Internet Draft DSMON MIB October 2001
::= { dsmonPdistObjects 3 }
dsmonPdistTopNCtlEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonPdistTopNCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonPdistTopNTable to be created and maintained
by the agent."
INDEX { dsmonPdistTopNCtlIndex }
::= { dsmonPdistTopNCtlTable 1 }
DsmonPdistTopNCtlEntry ::= SEQUENCE {
dsmonPdistTopNCtlIndex Integer32,
dsmonPdistTopNCtlPdistIndex Integer32,
dsmonPdistTopNCtlRateBase INTEGER,
dsmonPdistTopNCtlTimeRemaining Integer32,
dsmonPdistTopNCtlGeneratedReprts Counter32,
dsmonPdistTopNCtlDuration Integer32,
dsmonPdistTopNCtlRequestedSize Integer32,
dsmonPdistTopNCtlGrantedSize Integer32,
dsmonPdistTopNCtlStartTime TimeStamp,
dsmonPdistTopNCtlOwner OwnerString,
dsmonPdistTopNCtlStatus RowStatus
}
dsmonPdistTopNCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNCtlTable, with the same dsmonPdistTopNCtlIndex
value as this object. Each entry in this table defines one
Expires April 26, 2002 [Page 46]
Internet Draft DSMON MIB October 2001
Top N report prepared on behalf of the dsmonPdistStatsEntry
collection with the same dsmonPdistCtlIndex as this object."
::= { dsmonPdistTopNCtlEntry 1 }
dsmonPdistTopNCtlPdistIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonPdistTable for which a top N report will be
prepared on behalf of this entry. The dsmonPdistTable is
identified by the value of the dsmonPdistCtlIndex for that
table - that value is used here to identify the particular
table.
This object MUST NOT be modified if the associated
dsmonPdistTopNCtlStatus object is equal to active(1)."
::= { dsmonPdistTopNCtlEntry 2 }
dsmonPdistTopNCtlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonPdistTopNPkts(1),
dsmonPdistTopNOctets(2),
dsmonPdistTopNHCPkts(3),
dsmonPdistTopNHCOctets(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable for each dsmonPdist that the
dsmonPdistTopNRate and dsmonPdistTopNHCRate variables are
based upon. Each dsmonPdistTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonPdistStatsTable counter,
identified by this object.
The following table identifies the dsmonPdistTable counter
associated with each enumeration:
Enumeration RateBase MIB Object
----------- -------------------
dsmonPdistTopNPkts dsmonPdistStatsPkts
dsmonPdistTopNOctets dsmonPdistStatsOctets
dsmonPdistTopNHCPkts dsmonPdistStatsHCPkts
dsmonPdistTopNHCOctets dsmonPdistStatsHCOctets
Expires April 26, 2002 [Page 47]
Internet Draft DSMON MIB October 2001
Note that the dsmonPdistTopNHCPkts and
dsmonPdistTopNHCOctets enumerations are only available if
the agent supports High Capacity monitoring.
This object MUST NOT be modified if the associated
dsmonPdistTopNCtlStatus object is equal to active(1)."
::= { dsmonPdistTopNCtlEntry 3 }
dsmonPdistTopNCtlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonPdistTopNCtlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonPdistTopNCtlTimeRemaining. Thus the management station
may simply read the resulting reports repeatedly, checking
the startTime and duration each time to ensure that a report
was not missed or that the report parameters were not
changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonPdistTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonPdistTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonPdistTopNCtlEntry 4 }
dsmonPdistTopNCtlGeneratedReprts OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
Expires April 26, 2002 [Page 48]
Internet Draft DSMON MIB October 2001
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonPdistTopNCtlEntry 5 }
dsmonPdistTopNCtlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonPdistTopNCtlTimeRemaining object is
set, this object shall be set by the probe to the same value
and shall not be modified until the next time the
dsmonPdistTopNCtlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonPdistTopNCtlEntry."
::= { dsmonPdistTopNCtlEntry 6 }
dsmonPdistTopNCtlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries requested for this
report.
When this object is created or modified, the probe SHOULD
set dsmonPdistTopNCtlGrantedSize as closely to this object
as is possible for the particular probe implementation and
available resources."
DEFVAL { 150 }
::= { dsmonPdistTopNCtlEntry 7 }
dsmonPdistTopNCtlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
Expires April 26, 2002 [Page 49]
Internet Draft DSMON MIB October 2001
DESCRIPTION
"The maximum number of dsmonPdist entries in this report.
When the associated dsmonPdistTopNCtlRequestedSize object is
created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
MUST NOT lower this value except as a result of a set to the
associated dsmonPdistTopNCtlRequestedSize object.
Protocol entries with the highest value of
dsmonPdistTopNRate or dsmonPdistTopNHCRate (depending on the
value of the associated dsmonPdistTopNCtlRateBase object)
shall be placed in this table in decreasing order of this
rate until there is no more room or until there are no more
dsmonPdist entries."
::= { dsmonPdistTopNCtlEntry 8 }
dsmonPdistTopNCtlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonPdistTopNCtlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonPdistTopNCtlEntry 9 }
dsmonPdistTopNCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistTopNCtlEntry 10 }
dsmonPdistTopNCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
Expires April 26, 2002 [Page 50]
Internet Draft DSMON MIB October 2001
STATUS current
DESCRIPTION
"The status of this dsmonPdistTopNCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistTopNTable shall be deleted by the
agent."
::= { dsmonPdistTopNCtlEntry 11 }
--
-- dsmonPdist TopN Table
--
dsmonPdistTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those protocol distribution entries
that have counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonPdistTopNCtlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the dsmonPdistTopNCtlTable.
Note that dsmonPdist entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonPdistTopN reports."
::= { dsmonPdistObjects 4 }
dsmonPdistTopNEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNTable.
Expires April 26, 2002 [Page 51]
Internet Draft DSMON MIB October 2001
The dsmonPdistTopNCtlIndex value in the index identifies the
dsmonPdistTopNCtlEntry on whose behalf this entry was
created. Entries in this table are ordered from 1 to 'N',
where lower numbers represent higher values of the rate base
object, over the report interval."
INDEX { dsmonPdistTopNCtlIndex, dsmonPdistTopNIndex }
::= { dsmonPdistTopNTable 1 }
DsmonPdistTopNEntry ::= SEQUENCE {
dsmonPdistTopNIndex Integer32,
dsmonPdistTopNPDLocalIndex Integer32,
dsmonPdistTopNAggGroup DsmonAggGroupIndex,
dsmonPdistTopNRate Gauge32,
dsmonPdistTopNRateOvfl Gauge32,
dsmonPdistTopNHCRate CounterBasedGauge64
}
dsmonPdistTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report. Note that 'N' may change over time, and may
also be less than the dsmonPdistTopNCtlGrantedSize value
associated with this entry."
::= { dsmonPdistTopNEntry 1 }
dsmonPdistTopNPDLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonPdistTopN entry."
::= { dsmonPdistTopNEntry 2 }
dsmonPdistTopNAggGroup OBJECT-TYPE
Expires April 26, 2002 [Page 52]
Internet Draft DSMON MIB October 2001
SYNTAX DsmonAggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The DSCP aggregation group index value associated with
protocol identified in this entry. This object identifies
the dsmonAggGroupEntry with the same dsmonAggControlIndex
value as the associated dsmonPdistCtlAggProfile object and
the same dsmonAggGroupIndex value as this object."
::= { dsmonPdistTopNEntry 3 }
dsmonPdistTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNCtlRateBase.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the the least significant 32 bits
of the associated dsmonPdistTopNHCRate object."
::= { dsmonPdistTopNEntry 4 }
dsmonPdistTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the upper 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Expires April 26, 2002 [Page 53]
Internet Draft DSMON MIB October 2001
Capacity monitoring is not supported."
::= { dsmonPdistTopNEntry 5 }
dsmonPdistTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNCtlRateBase.
If the associated dsmonPdistTopNCtlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero, and the associated
dsmonPdistTopNRate object will contain the change in the
selected variable during the sampling interval.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonPdistTopNEntry 6 }
-- ***********************************************************
-- * *
-- * P E R - H O S T C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- NL Host Statistics Control Table
--
dsmonHostCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls setup of per aggregation group, per network layer
host distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
Expires April 26, 2002 [Page 54]
Internet Draft DSMON MIB October 2001
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonHostObjects 1 }
dsmonHostCtlEntry OBJECT-TYPE
SYNTAX DsmonHostCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonHostTable to be created and maintained by
the agent."
INDEX { dsmonHostCtlIndex }
::= { dsmonHostCtlTable 1 }
DsmonHostCtlEntry ::= SEQUENCE {
dsmonHostCtlIndex Integer32,
dsmonHostCtlDataSource DataSource,
dsmonHostCtlAggProfile DsmonAggProfileIndex,
dsmonHostCtlMaxDesiredEntries Integer32,
dsmonHostCtlIPv4PrefixLen Integer32,
dsmonHostCtlIPv6PrefixLen Integer32,
dsmonHostCtlDroppedFrames Counter32,
dsmonHostCtlInserts Counter32,
dsmonHostCtlDeletes Counter32,
dsmonHostCtlCreateTime LastCreateTime,
dsmonHostCtlOwner OwnerString,
dsmonHostCtlStatus RowStatus
}
dsmonHostCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
Expires April 26, 2002 [Page 55]
Internet Draft DSMON MIB October 2001
DESCRIPTION
"An arbitrary and unique index for this dsmonHostCtlEntry."
::= { dsmonHostCtlEntry 1 }
dsmonHostCtlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the associated dsmonHostTable.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
::= { dsmonHostCtlEntry 2 }
dsmonHostCtlAggProfile OBJECT-TYPE
SYNTAX DsmonAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonHostCtlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonHost collection. In this case, the
associated dsmonHostCtlStatus object will be changed to the
'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
::= { dsmonHostCtlEntry 3 }
Expires April 26, 2002 [Page 56]
Internet Draft DSMON MIB October 2001
dsmonHostCtlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonHostTable on behalf of this control entry. The probe
will not create more than this number of associated entries
in the table, but MAY choose to create fewer entries in this
table for any reason including the lack of resources.
If this value is set to -1, the probe MAY create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
::= { dsmonHostCtlEntry 4 }
dsmonHostCtlIPv4PrefixLen OBJECT-TYPE
SYNTAX Integer32 (8..32)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the host
address field for encapsulations of IPv4, that should be
maintained in this collection. This object controls how the
dsmonHostAddress object is derived for packets which contain
an encapsulation of IPv4.
If this object has a value less than 32, then 'm' rightmost
bits, where 'm' is equal to '32 -
dsmonHostCtlIPv4PrefixLen', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
If this object is equal to 32, then no bits are cleared in
each dsmonHostAddress field.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
DEFVAL { 32 }
::= { dsmonHostCtlEntry 5 }
Expires April 26, 2002 [Page 57]
Internet Draft DSMON MIB October 2001
dsmonHostCtlIPv6PrefixLen OBJECT-TYPE
SYNTAX Integer32 (8..128)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the host
address field for encapsulations of IPv6, that should be
maintained in this collection. This object controls how the
dsmonHostAddress object is derived for packets which contain
an encapsulation of IPv6.
If this object has a value less than 128, then 'm' rightmost
bits, where 'm' is equal to '128 -
dsmonHostCtlIPv6PrefixLen', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
If this object is equal to 128, then no bits are cleared in
each dsmonHostAddress field.
This object MUST NOT be modified if the associated
dsmonHostCtlStatus object is equal to active(1)."
DEFVAL { 128 }
::= { dsmonHostCtlEntry 6 }
dsmonHostCtlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for the associated
dsmonHost entries for whatever reason. Most often, this
event occurs when the probe is out of some resources and
decides to shed load from this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that if the dsmonHostTable is inactive because no
appropriate protocols are enabled in the protocol directory,
Expires April 26, 2002 [Page 58]
Internet Draft DSMON MIB October 2001
this value SHOULD be 0.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonHostCtlEntry 7 }
dsmonHostCtlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been inserted
into the dsmonHost table. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonHostCtlDeletes from dsmonHostCtlInserts."
::= { dsmonHostCtlEntry 8 }
dsmonHostCtlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been deleted from
the dsmonHost table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Expires April 26, 2002 [Page 59]
Internet Draft DSMON MIB October 2001
Note that the table size can be determined by subtracting
dsmonHostCtlDeletes from dsmonHostCtlInserts."
::= { dsmonHostCtlEntry 9 }
dsmonHostCtlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonHostCtlEntry 10 }
dsmonHostCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostCtlEntry 11 }
dsmonHostCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTable shall be deleted."
::= { dsmonHostCtlEntry 12 }
--
-- NL Host Statistics Table
--
dsmonHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostEntry
MAX-ACCESS not-accessible
Expires April 26, 2002 [Page 60]
Internet Draft DSMON MIB October 2001
STATUS current
DESCRIPTION
"A collection of statistics for particular network protocols
which contain a DS field, and that has been discovered on a
particular dataSource.
The probe will add to this table all appropriate network
protocols, for each network address seen as the source or
destination address in all packets with no MAC errors, and
will increment octet and packet counts in the table for all
packets with no MAC errors.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted, and the
agent will not process packets on behalf of any
dsmonHostCtlEntry."
::= { dsmonHostObjects 2 }
dsmonHostEntry OBJECT-TYPE
SYNTAX DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each
aggregation group index configured for collection per host
address, as identified in the dsmonAggProfileTable.
The dsmonHostCtlIndex value in the index identifies the
dsmonHostCtlEntry on whose behalf this entry was created.
The protocolDirLocalIndex value in the index identifies the
specific network layer protocol encapsulation associated
with each entry, and the network protocol type of the
dsmonHostAddress object. It MUST identify a
protocolDirEntry which contains a DS field (e.g., IPv4 or
IPv6). Note that if a protocol encapsulation with multiple
network layers is specified, then associated entries in this
table refer to the innermost network protocol layer host
address.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value.
Expires April 26, 2002 [Page 61]
Internet Draft DSMON MIB October 2001
An example of the indexing of this entry is
dsmonHostOutPkts.1.27273.3.200.4.171.69.120.0"
INDEX { dsmonHostCtlIndex,
dsmonHostTimeMark,
dsmonAggGroupIndex,
protocolDirLocalIndex,
dsmonHostAddress }
::= { dsmonHostTable 1 }
DsmonHostEntry ::= SEQUENCE {
dsmonHostTimeMark TimeFilter,
dsmonHostAddress OCTET STRING,
dsmonHostInPkts ZeroBasedCounter32,
dsmonHostInOctets ZeroBasedCounter32,
dsmonHostInOvflPkts ZeroBasedCounter32,
dsmonHostInOvflOctets ZeroBasedCounter32,
dsmonHostInHCPkts ZeroBasedCounter64,
dsmonHostInHCOctets ZeroBasedCounter64,
dsmonHostOutPkts ZeroBasedCounter32,
dsmonHostOutOctets ZeroBasedCounter32,
dsmonHostOutOvflPkts ZeroBasedCounter32,
dsmonHostOutOvflOctets ZeroBasedCounter32,
dsmonHostOutHCPkts ZeroBasedCounter64,
dsmonHostOutHCOctets ZeroBasedCounter64,
dsmonHostCreateTime LastCreateTime
}
dsmonHostTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonHostEntry 1 }
dsmonHostAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0 .. 65535))
MAX-ACCESS not-accessible
STATUS current
Expires April 26, 2002 [Page 62]
Internet Draft DSMON MIB October 2001
DESCRIPTION
"The network address for this dsmonHostEntry.
This object is encoded according to the protocol type
indicated by the protocolDirLocalIndex value in the index.
In addition, this object may have some 'rightmost' bits
cleared to zero for counting purposes, as indicated by the
associated dsmonHostCtlIPv4PrefixLen or
dsmonHostCtlIPv6PrefixLen objects."
::= { dsmonHostEntry 2 }
dsmonHostInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated aggregation group, and transmitted
to this address, since this entry was added to the
dsmonHostTable. Note that this is the number of link-layer
packets, so if a single network-layer packet is fragmented
into several link-layer frames, this counter is incremented
several times."
::= { dsmonHostEntry 3 }
dsmonHostInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in all packets, transmitted to this
address and using one of the DSCP values in the indicated
aggregation group, since this entry was added to the
dsmonHostTable (excluding framing bits but including FCS
octets), excluding those octets in packets that contained
errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 4 }
Expires April 26, 2002 [Page 63]
Internet Draft DSMON MIB October 2001
dsmonHostInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 5 }
dsmonHostInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCOctets object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 6 }
dsmonHostInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 7 }
dsmonHostInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
Expires April 26, 2002 [Page 64]
Internet Draft DSMON MIB October 2001
dataSource."
::= { dsmonHostEntry 8 }
dsmonHostOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated aggregation group, and transmitted
by this address, since this entry was added to the
dsmonHostTable. Note that this is the number of link-layer
packets, so if a single network-layer packet is fragmented
into several link-layer frames, this counter is incremented
several times."
::= { dsmonHostEntry 9 }
dsmonHostOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets, transmitted by this address and using
one of the DSCP values in the identified aggregation group,
since this entry was added to the dsmonHostTable (excluding
framing bits but including FCS octets), excluding those
octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 10 }
dsmonHostOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostOutPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 11 }
Expires April 26, 2002 [Page 65]
Internet Draft DSMON MIB October 2001
dsmonHostOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonHostEntry 12 }
dsmonHostOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 13 }
dsmonHostOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonHostEntry 14 }
dsmonHostCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonHost entry was last
instantiated by the agent. This can be used by the
management station to ensure that the entry has not been
Expires April 26, 2002 [Page 66]
Internet Draft DSMON MIB October 2001
deleted and recreated between polls."
::= { dsmonHostEntry 15 }
--
-- Per-Protocol Per-Host NL Statistics TopN Control Table
--
dsmonHostTopNCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonHost entries according to a selected
metric.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonHostObjects 3 }
dsmonHostTopNCtlEntry OBJECT-TYPE
SYNTAX DsmonHostTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostTopNCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonHostTopNTable to be created and maintained
by the agent."
INDEX { dsmonHostTopNCtlIndex }
::= { dsmonHostTopNCtlTable 1 }
Expires April 26, 2002 [Page 67]
Internet Draft DSMON MIB October 2001
DsmonHostTopNCtlEntry ::= SEQUENCE {
dsmonHostTopNCtlIndex Integer32,
dsmonHostTopNCtlHostIndex Integer32,
dsmonHostTopNCtlRateBase INTEGER,
dsmonHostTopNCtlTimeRemaining Integer32,
dsmonHostTopNCtlGeneratedReports Counter32,
dsmonHostTopNCtlDuration Integer32,
dsmonHostTopNCtlRequestedSize Integer32,
dsmonHostTopNCtlGrantedSize Integer32,
dsmonHostTopNCtlStartTime TimeStamp,
dsmonHostTopNCtlOwner OwnerString,
dsmonHostTopNCtlStatus RowStatus
}
dsmonHostTopNCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNCtlTable. Each such entry defines one Top N
report prepared for one RMON dataSource."
::= { dsmonHostTopNCtlEntry 1 }
dsmonHostTopNCtlHostIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonHostTable for which a top N report will be
prepared on behalf of this entry. The dsmonHostTable is
identified by the value of the dsmonHostCtlIndex for that
table - that value is used here to identify the particular
table.
This object MUST NOT be modified if the associated
dsmonHostTopNCtlStatus object is equal to active(1)."
::= { dsmonHostTopNCtlEntry 2 }
dsmonHostTopNCtlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonHostTopNInPkts(1),
dsmonHostTopNInOctets(2),
dsmonHostTopNOutPkts(3),
dsmonHostTopNOutOctets(4),
Expires April 26, 2002 [Page 68]
Internet Draft DSMON MIB October 2001
dsmonHostTopNTotalPkts(5),
dsmonHostTopNTotalOctets(6),
dsmonHostTopNInHCPkts(7),
dsmonHostTopNInHCOctets(8),
dsmonHostTopNOutHCPkts(9),
dsmonHostTopNOutHCOctets(10),
dsmonHostTopNTotalHCPkts(11),
dsmonHostTopNTotalHCOctets(12)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable(s) for each dsmonHost that the
dsmonHostTopNRate and dsmonHostTopNHCRate variables are
based upon. Each dsmonHostTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonHostTable counter(s),
identified by this object.
The following table identifies the dsmonHostTable counters
associated with each enumeration:
Enumeration RateBase MIB Objects
----------- --------------------
dsmonHostTopNInPkts dsmonHostInPkts
dsmonHostTopNInOctets dsmonHostInOctets
dsmonHostTopNOutPkts dsmonHostOutPkts
dsmonHostTopNOutOctets dsmonHostOutOctets
dsmonHostTopNTotalPkts dsmonHostInPkts +
dsmonHostOutPkts
dsmonHostTopNTotalOctets dsmonHostInOctets +
dsmonHostOutOctets
dsmonHostTopNInHCPkts dsmonHostInHCPkts
dsmonHostTopNInHCOctets dsmonHostInHCOctets
dsmonHostTopNOutHCPkts dsmonHostOutHCPkts
dsmonHostTopNOutHCOctets dsmonHostOutHCPkts
dsmonHostTopNTotalHCPkts dsmonHostInHCPkts +
dsmonHostOutHCPkts
dsmonHostTopNTotalHCOctets dsmonHostInHCOctets +
dsmonHostOutHCOctets
The following enumerations are only available if the agent
supports High Capacity monitoring:
Expires April 26, 2002 [Page 69]
Internet Draft DSMON MIB October 2001
dsmonHostTopNInHCPkts
dsmonHostTopNInHCOctets
dsmonHostTopNOutHCPkts
dsmonHostTopNOutHCOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
It is an implementation-specific matter whether an agent can
detect an overflow condition resulting from the addition of
two counter delta values for the following enumerations:
dsmonHostTopNTotalPkts
dsmonHostTopNTotalOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
In the event such an overflow condition can be detected by
the agent, the associated dsmonHostTopNRate,
dsmonHostTopNRateOvfl, and/or dsmonHostTopNHCRate objects
should be set to their maximum value.
This object MUST NOT be modified if the associated
dsmonHostTopNCtlStatus object is equal to active(1)."
::= { dsmonHostTopNCtlEntry 3 }
dsmonHostTopNCtlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonHostTopNCtlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonHostTopNCtlTimeRemaining. Thus the management station
may simply read the resulting reports repeatedly, checking
the startTime and duration each time to ensure that a report
was not missed or that the report parameters were not
changed.
Expires April 26, 2002 [Page 70]
Internet Draft DSMON MIB October 2001
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonHostTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonHostTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonHostTopNCtlEntry 4 }
dsmonHostTopNCtlGeneratedReports OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonHostTopNCtlEntry 5 }
dsmonHostTopNCtlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonHostTopNCtlTimeRemaining object is
set, this object shall be set by the probe to the same value
and shall not be modified until the next time the
dsmonHostTopNCtlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonHostTopNCtlEntry."
::= { dsmonHostTopNCtlEntry 6 }
dsmonHostTopNCtlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
Expires April 26, 2002 [Page 71]
Internet Draft DSMON MIB October 2001
DESCRIPTION
"The maximum number of dsmonHost entries requested for this
report.
When this object is created or modified, the probe SHOULD
set dsmonHostTopNCtlGrantedSize as closely to this object as
is possible for the particular probe implementation and
available resources."
DEFVAL { 150 }
::= { dsmonHostTopNCtlEntry 7 }
dsmonHostTopNCtlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries in this report.
When the associated dsmonHostTopNCtlRequestedSize object is
created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
MUST NOT lower this value except as a result of a set to the
associated dsmonHostTopNCtlRequestedSize object.
Protocol entries with the highest value of dsmonHostTopNRate
or dsmonHostTopNHCRate (depending on the value of the
associated dsmonHostTopNCtlRateBase object) shall be placed
in this table in decreasing order of this rate until there
is no more room or until there are no more dsmonHost
entries."
::= { dsmonHostTopNCtlEntry 8 }
dsmonHostTopNCtlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonHostTopNCtlTimeRemaining object was modified
to start the requested report or the time the report was
last automatically (re)started.
Expires April 26, 2002 [Page 72]
Internet Draft DSMON MIB October 2001
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonHostTopNCtlEntry 9 }
dsmonHostTopNCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostTopNCtlEntry 10 }
dsmonHostTopNCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostTopNCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTopNTable shall be deleted by the
agent."
::= { dsmonHostTopNCtlEntry 11 }
--
-- dsmonHost TopN Table
--
dsmonHostTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those dsmonHost entries that have
counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonHostTopNCtlEntry.
Expires April 26, 2002 [Page 73]
Internet Draft DSMON MIB October 2001
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the dsmonHostTopNCtlTable.
Note that dsmonHost entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonHostTopN reports."
::= { dsmonHostObjects 4 }
dsmonHostTopNEntry OBJECT-TYPE
SYNTAX DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNTable.
The dsmonHostTopNCtlIndex value in the index identifies the
dsmonHostTopNCtlEntry on whose behalf this entry was
created.
Entries in this table are ordered from 1 to 'N', where lower
numbers represent higher values of the rate base object,
over the report interval."
INDEX { dsmonHostTopNCtlIndex, dsmonHostTopNIndex }
::= { dsmonHostTopNTable 1 }
DsmonHostTopNEntry ::= SEQUENCE {
dsmonHostTopNIndex Integer32,
dsmonHostTopNPDLocalIndex Integer32,
dsmonHostTopNAddress OCTET STRING,
dsmonHostTopNAggGroup DsmonAggGroupIndex,
dsmonHostTopNRate Gauge32,
dsmonHostTopNRateOvfl Gauge32,
dsmonHostTopNHCRate CounterBasedGauge64
}
dsmonHostTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
Expires April 26, 2002 [Page 74]
Internet Draft DSMON MIB October 2001
::= { dsmonHostTopNEntry 1 }
dsmonHostTopNPDLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with the dsmonHostTopNAddress object in
this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonHostTopN entry."
::= { dsmonHostTopNEntry 2 }
dsmonHostTopNAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonHostAddress value for the network host identified
in this entry. The associated dsmonHostTopNPDLocalIndex
object identifies the network protocol type and the encoding
rules for this object."
::= { dsmonHostTopNEntry 3 }
dsmonHostTopNAggGroup OBJECT-TYPE
SYNTAX DsmonAggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregation group index value associated with host
identified in this entry. This object identifies the
dsmonAggGroupEntry with the same dsmonAggControlIndex value
as the associated dsmonHostCtlAggProfile object and the same
dsmonAggGroupIndex value as this object."
::= { dsmonHostTopNEntry 4 }
dsmonHostTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires April 26, 2002 [Page 75]
Internet Draft DSMON MIB October 2001
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by dsmonHostTopNCtlRateBase.
If the associated dsmonHostTopNCtlRateBase indicates a High
Capacity monitoring enumeration, (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
the least significant 32 bits of the associated
dsmonHostTopNHCRate object."
::= { dsmonHostTopNEntry 5 }
dsmonHostTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonHostTopNHCRate object.
If the associated dsmonHostTopNCtlRateBase is equal to any
of the High Capacity monitoring enumerations (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
upper 32 bits of the associated dsmonHostTopNHCRate object.
If the associated dsmonHostTopNCtlRateBase is not equal to
any of High Capacity monitoring enumerations, then this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonHostTopNEntry 6 }
dsmonHostTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by dsmonHostTopNCtlRateBase.
If the associated dsmonHostTopNCtlRateBase is not equal to
any of the High Capacity monitoring enumerations (e.g.,
'dsmonHostTopNInPkts'), then this object will contain the
value zero, and the associated dsmonHostTopNRate object will
Expires April 26, 2002 [Page 76]
Internet Draft DSMON MIB October 2001
contain the change in the selected variable during the
sampling interval.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonHostTopNEntry 7 }
-- **************************************************************
-- * *
-- * P E R - C O N V E R S I O N C O L L E C T I O N S *
-- * *
-- **************************************************************
--
-- AL Matrix Statistics Control Table
--
dsmonMatrixCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls setup of per aggregation group, per host-pair,
application protocol distribution statistics.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonMatrixObjects 1 }
dsmonMatrixCtlEntry OBJECT-TYPE
SYNTAX DsmonMatrixCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonMatrixCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
Expires April 26, 2002 [Page 77]
Internet Draft DSMON MIB October 2001
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Activation of a control row in this table will cause an
associated dsmonMatrixSDTable and dsmonMatrixDSTable to be
created and maintained by the agent."
INDEX { dsmonMatrixCtlIndex }
::= { dsmonMatrixCtlTable 1 }
DsmonMatrixCtlEntry ::= SEQUENCE {
dsmonMatrixCtlIndex Integer32,
dsmonMatrixCtlDataSource DataSource,
dsmonMatrixCtlAggProfile DsmonAggProfileIndex,
dsmonMatrixCtlMaxDesiredEntries Integer32,
dsmonMatrixCtlDroppedFrames Counter32,
dsmonMatrixCtlInserts Counter32,
dsmonMatrixCtlDeletes Counter32,
dsmonMatrixCtlCreateTime LastCreateTime,
dsmonMatrixCtlOwner OwnerString,
dsmonMatrixCtlStatus RowStatus
}
dsmonMatrixCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonMatrixCtlEntry."
::= { dsmonMatrixCtlEntry 1 }
dsmonMatrixCtlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the associated dsmonMatrixSDTable
and dsmonMatrixDSTable.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonMatrixCtlStatus object is equal to active(1)."
Expires April 26, 2002 [Page 78]
Internet Draft DSMON MIB October 2001
::= { dsmonMatrixCtlEntry 2 }
dsmonMatrixCtlAggProfile OBJECT-TYPE
SYNTAX DsmonAggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonMatrixCtlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonMatrix collection. In this case, the
associated dsmonMatrixCtlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonMatrixCtlStatus object is equal to active(1)."
::= { dsmonMatrixCtlEntry 3 }
dsmonMatrixCtlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonMatrix tables on behalf of this control entry. The
probe will not create more than this number of associated
entries in these tables, but may choose to create fewer
entries in this table for any reason including the lack of
resources.
If this value is set to -1, the probe may create any number
of entries in this table.
Expires April 26, 2002 [Page 79]
Internet Draft DSMON MIB October 2001
This object MUST NOT be modified if the associated
dsmonMatrixCtlStatus object is equal to active(1)."
::= { dsmonMatrixCtlEntry 4 }
dsmonMatrixCtlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for the associated
dsmonMatrixSD dsmonMatrixDS entries for whatever reason.
Most often, this event occurs when the probe is out of some
resources and decides to shed load from this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that if the dsmonMatrix tables are inactive because no
appropriate protocols are enabled in the protocol directory,
this value SHOULD be 0.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonMatrixCtlEntry 5 }
dsmonMatrixCtlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonMatrix entry has been inserted
into the dsmonMatrix tables. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2. The addition of a conversation into both the
dsmonMatrixSDTable and dsmonMatrixDSTable shall be counted
as two insertions (even though every addition into one table
must be accompanied by an insertion into the other).
To allow for efficient implementation strategies, agents may
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
Expires April 26, 2002 [Page 80]
Internet Draft DSMON MIB October 2001
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time. Note that the
sum of then dsmonMatrixSDTable and dsmonMatrixDSTable sizes
can be determined by subtracting dsmonMatrixCtlDeletes from
dsmonMatrixCtlInserts."
::= { dsmonMatrixCtlEntry 6 }
dsmonMatrixCtlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonMatrix entry has been deleted
from the dsmonMatrix tables (for any reason). If an entry
is deleted, then inserted, and then deleted, this counter
will be incremented by 2. The deletion of a conversation
from both the dsmonMatrixSDTable and dsmonMatrixDSTable
shall be counted as two deletions (even though every
deletion from one table must be accompanied by a deletion
from the other).
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonMatrixCtlDeletes from dsmonMatrixCtlInserts."
::= { dsmonMatrixCtlEntry 7 }
dsmonMatrixCtlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonMatrixCtlEntry 8 }
Expires April 26, 2002 [Page 81]
Internet Draft DSMON MIB October 2001
dsmonMatrixCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonMatrixCtlEntry 9 }
dsmonMatrixCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonMatrixCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonMatrixSDTable and dsmonMatrixDSTable
shall be deleted."
::= { dsmonMatrixCtlEntry 10 }
--
-- AL Matrix SD Statistics Table
--
dsmonMatrixSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of application traffic matrix entries which collect
statistics for conversations of a particular application
protocol between two network-level addresses. This table is
indexed first by the source address and then by the
destination address to make it convenient to collect all
statistics from a particular address.
The probe will add to this table all pairs of addresses for
all protocols seen in all packets with no MAC errors, and
will increment octet and packet counts in the table for all
packets with no MAC errors."
::= { dsmonMatrixObjects 2 }
Expires April 26, 2002 [Page 82]
Internet Draft DSMON MIB October 2001
dsmonMatrixSDEntry OBJECT-TYPE
SYNTAX DsmonMatrixSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixSDTable.
The dsmonMatrixCtlIndex value in the index identifies the
dsmonMatrixCtlEntry on whose behalf this entry was created.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value."
INDEX { dsmonMatrixCtlIndex,
dsmonMatrixTimeMark,
dsmonAggGroupIndex,
dsmonMatrixNLIndex,
dsmonMatrixSourceAddress,
dsmonMatrixDestAddress,
dsmonMatrixALIndex
}
::= { dsmonMatrixSDTable 1 }
DsmonMatrixSDEntry ::= SEQUENCE {
dsmonMatrixTimeMark TimeFilter,
dsmonMatrixNLIndex Integer32,
dsmonMatrixSourceAddress OCTET STRING,
dsmonMatrixDestAddress OCTET STRING,
dsmonMatrixALIndex Integer32,
dsmonMatrixSDPkts ZeroBasedCounter32,
dsmonMatrixSDOvflPkts ZeroBasedCounter32,
dsmonMatrixSDHCPkts ZeroBasedCounter64,
dsmonMatrixSDOctets ZeroBasedCounter32,
dsmonMatrixSDOvflOctets ZeroBasedCounter32,
dsmonMatrixSDHCOctets ZeroBasedCounter64,
dsmonMatrixSDCreateTime LastCreateTime
}
dsmonMatrixTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
Expires April 26, 2002 [Page 83]
Internet Draft DSMON MIB October 2001
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonMatrixSDEntry 1 }
dsmonMatrixNLIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value of a protocolDirEntry
representing the specific network layer protocol
encapsulation associated with each entry, and the network
protocol type of the dsmonMatrixSourceAddress and
dsmonMatrixDestAddress objects."
::= { dsmonMatrixSDEntry 2 }
dsmonMatrixSourceAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..65535))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network source address for this dsmonMatrix entry.
This is represented as an octet string with specific
semantics and length as identified by the dsmonMatrixNLIndex
component of the index.
For example, if the dsmonMatrixNLIndex indicates an
encapsulation of IPv4, this object is encoded as a length
octet of 4, followed by the 4 octets of the IPv4 address, in
network byte order."
::= { dsmonMatrixSDEntry 3 }
dsmonMatrixDestAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..65535))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network destination address for this dsmonMatrix entry.
This is represented as an octet string with specific
semantics and length as identified by the dsmonMatrixNLIndex
Expires April 26, 2002 [Page 84]
Internet Draft DSMON MIB October 2001
component of the index.
For example, if the dsmonMatrixNLIndex indicates an
encapsulation of IPv4, this object is encoded as a length
octet of 4, followed by the 4 octets of the IPv4 address, in
network byte order."
::= { dsmonMatrixSDEntry 4 }
dsmonMatrixALIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value of the protocolDirEntry
representing the specific application layer protocol
associated with each entry.
It MUST identify an protocolDirEntry which is a direct or
indirect descendant of the protocolDirEntry identified by
the associated dsmonMatrixNLIndex object."
::= { dsmonMatrixSDEntry 5 }
dsmonMatrixSDPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets of this protocol type (indicated by
the associated dsmonMatrixALIndex object) without errors
transmitted from the source address to the destination
address since this entry was added to the
dsmonMatrixSDTable. Note that this is the number of link-
layer packets, so if a single network-layer packet is
fragmented into several link-layer frames, this counter is
incremented several times."
::= { dsmonMatrixSDEntry 6 }
dsmonMatrixSDOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixSDPkts
counter has overflowed, since this entry was added to the
Expires April 26, 2002 [Page 85]
Internet Draft DSMON MIB October 2001
dsmonMatrixSDTable."
::= { dsmonMatrixSDEntry 7 }
dsmonMatrixSDHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixSDPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixSDEntry 8 }
dsmonMatrixSDOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets of this protocol type
transmitted from the source address to the destination
address since this entry was added to the dsmonMatrixSDTable
(excluding framing bits but including FCS octets), excluding
those octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonMatrixSDEntry 9 }
dsmonMatrixSDOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixSDOctets
counter has overflowed, since this entry was added to the
dsmonMatrixSDTable."
::= { dsmonMatrixSDEntry 10 }
dsmonMatrixSDHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
Expires April 26, 2002 [Page 86]
Internet Draft DSMON MIB October 2001
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixSDPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixSDEntry 11 }
dsmonMatrixSDCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this entry was last activated.
This can be used by the management station to ensure that
the entry has not been deleted and recreated between polls."
::= { dsmonMatrixSDEntry 12 }
--
-- AL Matrix DS Statistics Table
--
dsmonMatrixDSTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixDSEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of application traffic matrix entries which collect
statistics for conversations of a particular application
protocol between two network-level addresses. This table is
indexed first by the destination address and then by the
source address to make it convenient to collect all
statistics from a particular address.
The probe will add to this table all pairs of addresses for
all protocols seen in all packets with no MAC errors, and
will increment octet and packet counts in the table for all
packets with no MAC errors."
::= { dsmonMatrixObjects 3 }
dsmonMatrixDSEntry OBJECT-TYPE
Expires April 26, 2002 [Page 87]
Internet Draft DSMON MIB October 2001
SYNTAX DsmonMatrixDSEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixDSTable. Note that this
table is conceptually a re-ordered version of the
dsmonMatrixSDTable. Therefore, all of the index values from
that table are used by reference, and their semantics are
exactly as described in the dsmonMatrixSDTable.
The dsmonMatrixCtlIndex value in the index identifies the
dsmonMatrixCtlEntry on whose behalf this entry was created.
The dsmonMatrixTimeMark value in the index identifies the
Time Filter index for this table.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value.
The dsmonMatrixNLIndex value in the index identifies the
protocolDirLocalIndex value of a protocolDirEntry
representing the specific network layer protocol
encapsulation associated with each entry, and the network
protocol type of the dsmonMatrixSourceAddress and
dsmonMatrixDestAddress objects.
The dsmonMatrixDestAddress value in the index identifies the
network destination address for this dsmonMatrix entry.
The dsmonMatrixSourceAddress value in the index identifies
the network source address for this dsmonMatrix entry.
The dsmonMatrixALIndex value in the index identifies the
protocolDirLocalIndex value of the protocolDirEntry
representing the specific application layer protocol
associated with each entry."
INDEX { dsmonMatrixCtlIndex,
dsmonMatrixTimeMark,
dsmonAggGroupIndex,
dsmonMatrixNLIndex,
dsmonMatrixDestAddress,
dsmonMatrixSourceAddress,
dsmonMatrixALIndex
}
Expires April 26, 2002 [Page 88]
Internet Draft DSMON MIB October 2001
::= { dsmonMatrixDSTable 1 }
DsmonMatrixDSEntry ::= SEQUENCE {
dsmonMatrixDSPkts ZeroBasedCounter32,
dsmonMatrixDSOvflPkts ZeroBasedCounter32,
dsmonMatrixDSHCPkts ZeroBasedCounter64,
dsmonMatrixDSOctets ZeroBasedCounter32,
dsmonMatrixDSOvflOctets ZeroBasedCounter32,
dsmonMatrixDSHCOctets ZeroBasedCounter64,
dsmonMatrixDSCreateTime LastCreateTime
}
dsmonMatrixDSPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets of this protocol type (indicated by
the associated dsmonMatrixALIndex object) without errors
transmitted from the source address to the destination
address since this entry was added to the
dsmonMatrixDSTable. Note that this is the number of link-
layer packets, so if a single network-layer packet is
fragmented into several link-layer frames, this counter is
incremented several times."
::= { dsmonMatrixDSEntry 1 }
dsmonMatrixDSOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixDSPkts
counter has overflowed, since this entry was added to the
dsmonMatrixDSTable."
::= { dsmonMatrixDSEntry 2 }
dsmonMatrixDSHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixDSPkts object.
Expires April 26, 2002 [Page 89]
Internet Draft DSMON MIB October 2001
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixDSEntry 3 }
dsmonMatrixDSOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets of this protocol type
transmitted from the source address to the destination
address since this entry was added to the dsmonMatrixDSTable
(excluding framing bits but including FCS octets), excluding
those octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonMatrixDSEntry 4 }
dsmonMatrixDSOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonMatrixDSOctets
counter has overflowed, since this entry was added to the
dsmonMatrixDSTable."
::= { dsmonMatrixDSEntry 5 }
dsmonMatrixDSHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonMatrixDSPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity monitoring for a particular
dataSource."
::= { dsmonMatrixDSEntry 6 }
Expires April 26, 2002 [Page 90]
Internet Draft DSMON MIB October 2001
dsmonMatrixDSCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this entry was last activated.
This can be used by the management station to ensure that
the entry has not been deleted and recreated between polls."
::= { dsmonMatrixDSEntry 7 }
--
-- Per-Protocol Per-Matrix Statistics TopN Control Table
--
dsmonMatrixTopNCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonMatrix entries according to a selected
metric.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table. In this case,
the agent SHOULD return an error-status of
'resourceUnavailable(13)', as per section 4.2.5 of the
'Protocol Operations for SNMPv2' specification [RFC1905]."
::= { dsmonMatrixObjects 4 }
dsmonMatrixTopNCtlEntry OBJECT-TYPE
SYNTAX DsmonMatrixTopNCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixTopNCtlTable.
Entries are created and deleted from this table by
management action only, using the dsmonMatrixTopNCtlStatus
RowStatus object.
The agent SHOULD support non-volatile configuration of this
table, and upon system initialization, the table SHOULD be
initialized with the saved values.
Expires April 26, 2002 [Page 91]
Internet Draft DSMON MIB October 2001
Activation of a control row in this table will cause an
associated dsmonMatrixTopNTable to be created and maintained
by the agent."
INDEX { dsmonMatrixTopNCtlIndex }
::= { dsmonMatrixTopNCtlTable 1 }
DsmonMatrixTopNCtlEntry ::= SEQUENCE {
dsmonMatrixTopNCtlIndex Integer32,
dsmonMatrixTopNCtlMatrixIndex Integer32,
dsmonMatrixTopNCtlRateBase INTEGER,
dsmonMatrixTopNCtlTimeRemaining Integer32,
dsmonMatrixTopNCtlGeneratedRpts Counter32,
dsmonMatrixTopNCtlDuration Integer32,
dsmonMatrixTopNCtlRequestedSize Integer32,
dsmonMatrixTopNCtlGrantedSize Integer32,
dsmonMatrixTopNCtlStartTime TimeStamp,
dsmonMatrixTopNCtlOwner OwnerString,
dsmonMatrixTopNCtlStatus RowStatus
}
dsmonMatrixTopNCtlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonMatrixTopNCtlTable. Each such entry defines one Top N
report prepared for one RMON dataSource."
::= { dsmonMatrixTopNCtlEntry 1 }
dsmonMatrixTopNCtlMatrixIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonMatrixSDTable for which a top N report will be
prepared on behalf of this entry. The dsmonMatrixSDTable is
identified by the same value of the dsmonMatrixCtlIndex
object.
This object MUST NOT be modified if the associated
dsmonMatrixTopNCtlStatus object is equal to active(1)."
::= { dsmonMatrixTopNCtlEntry 2 }
dsmonMatrixTopNCtlRateBase OBJECT-TYPE
Expires April 26, 2002 [Page 92]
Internet Draft DSMON MIB October 2001
SYNTAX INTEGER {
dsmonMatrixTopNPkts(1),
dsmonMatrixTopNOctets(2),
dsmonMatrixTopNHCPkts(3),
dsmonMatrixTopNHCOctets(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable(s) for each dsmonMatrixSD entry that the
dsmonMatrixTopNRate and dsmonMatrixTopNHCRate variables are
based upon. Each dsmonMatrixTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonMatrixSDTable counter(s),
identified by this object.
The following table identifies the dsmonMatrixSDTable
counters associated with each enumeration:
Enumeration RateBase MIB Objects
----------- --------------------
dsmonMatrixTopNPkts dsmonMatrixSDPkts
dsmonMatrixTopNOctets dsmonMatrixSDOctets
dsmonMatrixTopNHCPkts dsmonMatrixSDHCPkts
dsmonMatrixTopNHCOctets dsmonMatrixSDHCOctets
The following enumerations are only available if the agent
supports High Capacity monitoring:
dsmonMatrixTopNHCPkts
dsmonMatrixTopNHCOctets
This object MUST NOT be modified if the associated
dsmonMatrixTopNCtlStatus object is equal to active(1)."
::= { dsmonMatrixTopNCtlEntry 3 }
dsmonMatrixTopNCtlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
Expires April 26, 2002 [Page 93]
Internet Draft DSMON MIB October 2001
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonMatrixTopNCtlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonMatrixTopNCtlTimeRemaining. Thus the management
station may simply read the resulting reports repeatedly,
checking the startTime and duration each time to ensure that
a report was not missed or that the report parameters were
not changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonMatrixTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonMatrixTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonMatrixTopNCtlEntry 4 }
dsmonMatrixTopNCtlGeneratedRpts OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonMatrixTopNCtlEntry 5 }
dsmonMatrixTopNCtlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonMatrixTopNCtlTimeRemaining object
is set, this object shall be set by the probe to the same
Expires April 26, 2002 [Page 94]
Internet Draft DSMON MIB October 2001
value and shall not be modified until the next time the
dsmonMatrixTopNCtlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonMatrixTopNCtlEntry."
::= { dsmonMatrixTopNCtlEntry 6 }
dsmonMatrixTopNCtlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonMatrix entries requested for
this report.
When this object is created or modified, the probe SHOULD
set dsmonMatrixTopNCtlGrantedSize as closely to this object
as is possible for the particular probe implementation and
available resources."
DEFVAL { 150 }
::= { dsmonMatrixTopNCtlEntry 7 }
dsmonMatrixTopNCtlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonMatrix entries in this report.
When the associated dsmonMatrixTopNCtlRequestedSize object
is created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
MUST NOT lower this value except as a result of a set to the
associated dsmonMatrixTopNCtlRequestedSize object.
Protocol entries with the highest value of
dsmonMatrixTopNRate or dsmonMatrixTopNHCRate (depending on
the value of the associated dsmonMatrixTopNCtlRateBase
object) shall be placed in this table in decreasing order of
this rate until there is no more room or until there are no
more dsmonMatrix entries."
::= { dsmonMatrixTopNCtlEntry 8 }
Expires April 26, 2002 [Page 95]
Internet Draft DSMON MIB October 2001
dsmonMatrixTopNCtlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonMatrixTopNCtlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonMatrixTopNCtlEntry 9 }
dsmonMatrixTopNCtlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonMatrixTopNCtlEntry 10 }
dsmonMatrixTopNCtlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonMatrixTopNCtlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonMatrixTopNTable shall be deleted by the
agent."
::= { dsmonMatrixTopNCtlEntry 11 }
--
-- dsmonMatrix TopN Table
--
dsmonMatrixTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonMatrixTopNEntry
Expires April 26, 2002 [Page 96]
Internet Draft DSMON MIB October 2001
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those dsmonMatrix entries that have
counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonMatrixTopNCtlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the dsmonMatrixTopNCtlTable.
Note that dsmonMatrix entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonMatrixTopN reports."
::= { dsmonMatrixObjects 5 }
dsmonMatrixTopNEntry OBJECT-TYPE
SYNTAX DsmonMatrixTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonMatrixTopNTable.
The dsmonMatrixTopNCtlIndex value in the index identifies
the dsmonMatrixTopNCtlEntry on whose behalf this entry was
created.
Entries in this table are ordered from 1 to 'N', where lower
numbers represent higher values of the rate base object,
over the report interval."
INDEX { dsmonMatrixTopNCtlIndex, dsmonMatrixTopNIndex }
::= { dsmonMatrixTopNTable 1 }
DsmonMatrixTopNEntry ::= SEQUENCE {
dsmonMatrixTopNIndex Integer32,
dsmonMatrixTopNAggGroup DsmonAggGroupIndex,
dsmonMatrixTopNNLIndex Integer32,
dsmonMatrixTopNSourceAddress OCTET STRING,
dsmonMatrixTopNDestAddress OCTET STRING,
dsmonMatrixTopNALIndex Integer32,
dsmonMatrixTopNPktRate Gauge32,
Expires April 26, 2002 [Page 97]
Internet Draft DSMON MIB October 2001
dsmonMatrixTopNPktRateOvfl Gauge32,
dsmonMatrixTopNHCPktRate CounterBasedGauge64,
dsmonMatrixTopNRevPktRate Gauge32,
dsmonMatrixTopNRevPktRateOvfl Gauge32,
dsmonMatrixTopNHCRevPktRate CounterBasedGauge64,
dsmonMatrixTopNOctetRate Gauge32,
dsmonMatrixTopNOctetRateOvfl Gauge32,
dsmonMatrixTopNHCOctetRate CounterBasedGauge64,
dsmonMatrixTopNRevOctetRate Gauge32,
dsmonMatrixTopNRevOctetRateOvfl Gauge32,
dsmonMatrixTopNHCRevOctetRate CounterBasedGauge64
}
dsmonMatrixTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonMatrixTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonMatrixTopNEntry 1 }
dsmonMatrixTopNAggGroup OBJECT-TYPE
SYNTAX DsmonAggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregation group index value associated with host
identified in this entry. This object identifies the
dsmonAggGroupEntry with the same dsmonAggControlIndex value
as the associated dsmonMatrixCtlAggProfile object and the
same dsmonAggGroupIndex value as this object."
::= { dsmonMatrixTopNEntry 2 }
dsmonMatrixTopNNLIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with the dsmonMatrixTopNSourceAddress
and dsmonMatrixTopNDestAddress objects in this entry.
Expires April 26, 2002 [Page 98]
Internet Draft DSMON MIB October 2001
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonMatrixTopN entry."
::= { dsmonMatrixTopNEntry 3 }
dsmonMatrixTopNSourceAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonMatrixSDSourceAddress value for the source network
host identified in this entry. The associated
dsmonMatrixTopNNLIndex object identifies the network
protocol type and the encoding rules for this object."
::= { dsmonMatrixTopNEntry 4 }
dsmonMatrixTopNDestAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonMatrixSDDestAddress value for the destination
network host identified in this entry. The associated
dsmonMatrixTopNNLIndex object identifies the network
protocol type and the encoding rules for this object."
::= { dsmonMatrixTopNEntry 5 }
dsmonMatrixTopNALIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
application protocol associated with this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonMatrixTopN entry."
::= { dsmonMatrixTopNEntry 6 }
dsmonMatrixTopNPktRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
Expires April 26, 2002 [Page 99]
Internet Draft DSMON MIB October 2001
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the dsmonMatrixSDPkts
object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNPkts, this variable will be used to sort this
report.
If the value of the dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the the least significant 32 bits of the
associated dsmonMatrixTopNHCPktRate object."
::= { dsmonMatrixTopNEntry 7 }
dsmonMatrixTopNPktRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCPktRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCPktRate object, otherwise this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 8 }
dsmonMatrixTopNHCPktRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the dsmonMatrixSDHCPkts
object.
Expires April 26, 2002 [Page 100]
Internet Draft DSMON MIB October 2001
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCPkts, this variable will be used to sort
this report.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 9 }
dsmonMatrixTopNRevPktRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSPkts object (note that the corresponding
dsmonMatrixSDPkts object selected is the one whose source
address is equal to dsmonMatrixTopNDestAddress and whose
destination address is equal to
dsmonMatrixTopNSourceAddress.)"
::= { dsmonMatrixTopNEntry 10 }
dsmonMatrixTopNRevPktRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCRevPktRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOCtets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCRevPktRate object, otherwise
this object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 11 }
dsmonMatrixTopNHCRevPktRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
Expires April 26, 2002 [Page 101]
Internet Draft DSMON MIB October 2001
DESCRIPTION
"The number of packets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSHCPkts object (note that the corresponding
dsmonMatrixSDHCPkts object selected is the one whose source
address is equal to dsmonMatrixTopNDestAddress and whose
destination address is equal to
dsmonMatrixTopNSourceAddress.)
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 12 }
dsmonMatrixTopNOctetRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the dsmonMatrixSDOctets
object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNOctets, this variable will be used to sort
this report.
If the value of the dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the the least significant 32 bits of the
associated dsmonMatrixTopNHCPktRate object."
::= { dsmonMatrixTopNEntry 13 }
dsmonMatrixTopNOctetRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonMatrixTopNHCOctetRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOctets, then this
object will contain the most significant 32 bits of the
Expires April 26, 2002 [Page 102]
Internet Draft DSMON MIB October 2001
associated dsmonMatrixTopNHCOctetRate object, otherwise this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 14 }
dsmonMatrixTopNHCOctetRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the source
host to the destination host during this sampling interval,
counted using the rules for counting the
dsmonMatrixSDHCOctets object.
If the value of dsmonMatrixTopNCtlRateBase is
dsmonMatrixTopNHCOctets, this variable will be used to sort
this report.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 15 }
dsmonMatrixTopNRevOctetRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSOctets object (note that the corresponding
dsmonMatrixSDOctets object selected is the one whose source
address is equal to dsmonMatrixTopNDestAddress and whose
destination address is equal to
dsmonMatrixTopNSourceAddress.)"
::= { dsmonMatrixTopNEntry 16 }
dsmonMatrixTopNRevOctetRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
Expires April 26, 2002 [Page 103]
Internet Draft DSMON MIB October 2001
"The most significant 32 bits of the associated
dsmonMatrixTopNHCRevOctetRate object.
If the associated dsmonMatrixTopNCtlRateBase is equal to
dsmonMatrixTopNHCPkts or dsmonMatrixTopNHCOCtets, then this
object will contain the most significant 32 bits of the
associated dsmonMatrixTopNHCRevPktRate object, otherwise
this object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 17 }
dsmonMatrixTopNHCRevOctetRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets seen of this protocol from the
destination host to the source host during this sampling
interval, counted using the rules for counting the
dsmonMatrixDSHCOctets object (note that the corresponding
dsmonMatrixSDHCOctets object selected is the one whose
source address is equal to dsmonMatrixTopNDestAddress and
whose destination address is equal to
dsmonMatrixTopNSourceAddress.)
The agent MAY choose not to instantiate this object if High
Capacity monitoring is not supported."
::= { dsmonMatrixTopNEntry 18 }
--
-- Conformance Section
--
dsmonCompliances OBJECT IDENTIFIER ::= { dsmonConformance 1 }
dsmonGroups OBJECT IDENTIFIER ::= { dsmonConformance 2 }
dsmonCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB."
MODULE -- this module
MANDATORY-GROUPS {
Expires April 26, 2002 [Page 104]
Internet Draft DSMON MIB October 2001
dsmonAggControlGroup,
dsmonStatsGroup,
dsmonCapsGroup
}
GROUP dsmonStatsHCGroup
DESCRIPTION
"The dsmonStatsHCGroup is mandatory for systems which
implement High Capacity monitoring."
GROUP dsmonPdistGroup
DESCRIPTION
"The dsmonPdistGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonPdistHCGroup
DESCRIPTION
"The dsmonPdistHCGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring on high capacity interfaces."
GROUP dsmonHostGroup
DESCRIPTION
"The dsmonHostGroup is mandatory for systems which implement
RMON-2 nlHostTable based network protocol monitoring."
GROUP dsmonHostHCGroup
DESCRIPTION
"The dsmonHostHCGroup is mandatory for systems which
implement RMON-2 nlHostTable based network protocol
monitoring, on high capacity interfaces."
GROUP dsmonMatrixGroup
DESCRIPTION
"The dsmonMatrixGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
GROUP dsmonMatrixHCGroup
DESCRIPTION
"The dsmonMatrixHCGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring, on high capacity interfaces."
Expires April 26, 2002 [Page 105]
Internet Draft DSMON MIB October 2001
::= { dsmonCompliances 1 }
dsmonHCCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB for agents which also
support High Capacity monitoring."
MODULE -- this module
MANDATORY-GROUPS {
dsmonAggControlGroup,
dsmonStatsGroup,
dsmonStatsHCGroup,
dsmonCapsGroup
}
GROUP dsmonPdistGroup
DESCRIPTION
"The dsmonPdistGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonPdistHCGroup
DESCRIPTION
"The dsmonPdistHCGroup is mandatory for systems which
implement RMON-2 protocolDirTable based protocol
distribution monitoring."
GROUP dsmonHostGroup
DESCRIPTION
"The dsmonHostGroup is mandatory for systems which implement
RMON-2 nlHostTable based network protocol monitoring."
GROUP dsmonHostHCGroup
DESCRIPTION
"The dsmonHostHCGroup is mandatory for systems which
implement RMON-2 nlHostTable based network protocol
monitoring."
GROUP dsmonMatrixGroup
DESCRIPTION
"The dsmonMatrixGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
Expires April 26, 2002 [Page 106]
Internet Draft DSMON MIB October 2001
monitoring."
GROUP dsmonMatrixHCGroup
DESCRIPTION
"The dsmonMatrixHCGroup is mandatory for systems which
implement RMON-2 alMatrix based application protocol
monitoring."
::= { dsmonCompliances 2 }
-- Object Groups
dsmonAggControlGroup OBJECT-GROUP
OBJECTS {
dsmonMaxAggGroups,
dsmonAggControlLocked,
dsmonAggControlChanges,
dsmonAggControlLastChangeTime,
dsmonAggControlDescr,
dsmonAggControlOwner,
dsmonAggControlStatus,
dsmonAggGroupIndex,
dsmonAggGroupDescr,
dsmonAggGroupStatus
}
STATUS current
DESCRIPTION
"A collection of objects used to configure and manage
aggregation groups for DSMON collection purposes."
::= { dsmonGroups 1 }
dsmonStatsGroup OBJECT-GROUP
OBJECTS {
dsmonStatsControlDataSource,
dsmonStatsControlAggProfile,
dsmonStatsControlDroppedFrames,
dsmonStatsControlCreateTime,
dsmonStatsControlOwner,
dsmonStatsControlStatus,
dsmonStatsInPkts,
dsmonStatsInOctets,
dsmonStatsOutPkts,
Expires April 26, 2002 [Page 107]
Internet Draft DSMON MIB October 2001
dsmonStatsOutOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics."
::= { dsmonGroups 2 }
dsmonStatsOvflGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInOvflPkts,
dsmonStatsInOvflOctets,
dsmonStatsOutOvflPkts,
dsmonStatsOutOvflOctets
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per-DSCP overflow
counters for systems with high capacity data sources, but
without support for the Counter64 data type."
::= { dsmonGroups 3 }
dsmonStatsHCGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInHCPkts,
dsmonStatsInHCOctets,
dsmonStatsOutHCPkts,
dsmonStatsOutHCOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics for
high capacity data sources."
::= { dsmonGroups 4 }
dsmonPdistGroup OBJECT-GROUP
OBJECTS {
dsmonPdistCtlDataSource,
dsmonPdistCtlAggProfile,
dsmonPdistCtlMaxDesiredEntries,
dsmonPdistCtlDroppedFrames,
dsmonPdistCtlInserts,
dsmonPdistCtlDeletes,
dsmonPdistCtlCreateTime,
dsmonPdistCtlOwner,
dsmonPdistCtlStatus,
Expires April 26, 2002 [Page 108]
Internet Draft DSMON MIB October 2001
dsmonPdistStatsPkts,
dsmonPdistStatsOctets,
dsmonPdistStatsCreateTime,
dsmonPdistTopNCtlPdistIndex,
dsmonPdistTopNCtlRateBase,
dsmonPdistTopNCtlTimeRemaining,
dsmonPdistTopNCtlGeneratedReprts,
dsmonPdistTopNCtlDuration,
dsmonPdistTopNCtlRequestedSize,
dsmonPdistTopNCtlGrantedSize,
dsmonPdistTopNCtlStartTime,
dsmonPdistTopNCtlOwner,
dsmonPdistTopNCtlStatus,
dsmonPdistTopNPDLocalIndex,
dsmonPdistTopNAggGroup,
dsmonPdistTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB."
::= { dsmonGroups 5 }
dsmonPdistOvflGroup OBJECT-GROUP
OBJECTS {
dsmonPdistStatsOvflPkts,
dsmonPdistStatsOvflOctets,
dsmonPdistTopNRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per-protocol DSCP
overflow counters for systems with high capacity data
sources, but without support for the Counter64 data type."
::= { dsmonGroups 6 }
dsmonPdistHCGroup OBJECT-GROUP
OBJECTS {
dsmonPdistStatsHCPkts,
dsmonPdistStatsHCOctets,
dsmonPdistTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
Expires April 26, 2002 [Page 109]
Internet Draft DSMON MIB October 2001
monitoring extensions to the RMON-2 MIB for High Capacity
networks."
::= { dsmonGroups 7 }
dsmonHostGroup OBJECT-GROUP
OBJECTS {
dsmonHostCtlDataSource,
dsmonHostCtlAggProfile,
dsmonHostCtlMaxDesiredEntries,
dsmonHostCtlIPv4PrefixLen,
dsmonHostCtlIPv6PrefixLen,
dsmonHostCtlDroppedFrames,
dsmonHostCtlInserts,
dsmonHostCtlDeletes,
dsmonHostCtlCreateTime,
dsmonHostCtlOwner,
dsmonHostCtlStatus,
dsmonHostInPkts,
dsmonHostInOctets,
dsmonHostOutPkts,
dsmonHostOutOctets,
dsmonHostCreateTime,
dsmonHostTopNCtlHostIndex,
dsmonHostTopNCtlRateBase,
dsmonHostTopNCtlTimeRemaining,
dsmonHostTopNCtlGeneratedReports,
dsmonHostTopNCtlDuration,
dsmonHostTopNCtlRequestedSize,
dsmonHostTopNCtlGrantedSize,
dsmonHostTopNCtlStartTime,
dsmonHostTopNCtlOwner,
dsmonHostTopNCtlStatus,
dsmonHostTopNPDLocalIndex,
dsmonHostTopNAddress,
dsmonHostTopNAggGroup,
dsmonHostTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per Host monitoring
functions."
::= { dsmonGroups 8 }
dsmonHostOvflGroup OBJECT-GROUP
OBJECTS {
Expires April 26, 2002 [Page 110]
Internet Draft DSMON MIB October 2001
dsmonHostInOvflPkts,
dsmonHostInOvflOctets,
dsmonHostOutOvflPkts,
dsmonHostOutOvflOctets,
dsmonHostTopNRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per host DSCP overflow
counters for systems with high capacity data sources, but
without support for the Counter64 data type."
::= { dsmonGroups 9 }
dsmonHostHCGroup OBJECT-GROUP
OBJECTS {
dsmonHostInHCPkts,
dsmonHostInHCOctets,
dsmonHostOutHCPkts,
dsmonHostOutHCOctets,
dsmonHostTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per Host monitoring
functions for High Capacity networks."
::= { dsmonGroups 10 }
dsmonCapsGroup OBJECT-GROUP
OBJECTS {
dsmonCapabilities
}
STATUS current
DESCRIPTION
"A collection of objects providing an indication of the
DSMON monitoring functions supported by the agent."
::= { dsmonGroups 11 }
dsmonMatrixGroup OBJECT-GROUP
OBJECTS {
dsmonMatrixCtlDataSource,
dsmonMatrixCtlAggProfile,
dsmonMatrixCtlMaxDesiredEntries,
dsmonMatrixCtlDroppedFrames,
dsmonMatrixCtlInserts,
dsmonMatrixCtlDeletes,
Expires April 26, 2002 [Page 111]
Internet Draft DSMON MIB October 2001
dsmonMatrixCtlCreateTime,
dsmonMatrixCtlOwner,
dsmonMatrixCtlStatus,
dsmonMatrixSDPkts,
dsmonMatrixSDOctets,
dsmonMatrixSDCreateTime,
dsmonMatrixDSPkts,
dsmonMatrixDSOctets,
dsmonMatrixDSCreateTime,
dsmonMatrixTopNCtlMatrixIndex,
dsmonMatrixTopNCtlRateBase,
dsmonMatrixTopNCtlTimeRemaining,
dsmonMatrixTopNCtlGeneratedRpts,
dsmonMatrixTopNCtlDuration,
dsmonMatrixTopNCtlRequestedSize,
dsmonMatrixTopNCtlGrantedSize,
dsmonMatrixTopNCtlStartTime,
dsmonMatrixTopNCtlOwner,
dsmonMatrixTopNCtlStatus,
dsmonMatrixTopNAggGroup,
dsmonMatrixTopNNLIndex,
dsmonMatrixTopNSourceAddress,
dsmonMatrixTopNDestAddress,
dsmonMatrixTopNALIndex,
dsmonMatrixTopNPktRate,
dsmonMatrixTopNRevPktRate,
dsmonMatrixTopNOctetRate,
dsmonMatrixTopNRevOctetRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per conversation
monitoring functions."
::= { dsmonGroups 12 }
dsmonMatrixOvflGroup OBJECT-GROUP
OBJECTS {
dsmonMatrixSDOvflPkts,
dsmonMatrixSDOvflOctets,
dsmonMatrixDSOvflPkts,
dsmonMatrixDSOvflOctets,
dsmonMatrixTopNPktRateOvfl,
dsmonMatrixTopNRevPktRateOvfl,
dsmonMatrixTopNOctetRateOvfl,
dsmonMatrixTopNRevOctetRateOvfl
Expires April 26, 2002 [Page 112]
Internet Draft DSMON MIB October 2001
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per conversation
monitoring functions for systems with high capacity data
sources, but without support for the Counter64 data type."
::= { dsmonGroups 13 }
dsmonMatrixHCGroup OBJECT-GROUP
OBJECTS {
dsmonMatrixSDHCPkts,
dsmonMatrixSDHCOctets,
dsmonMatrixDSHCPkts,
dsmonMatrixDSHCOctets,
dsmonMatrixTopNHCPktRate,
dsmonMatrixTopNHCRevPktRate,
dsmonMatrixTopNHCOctetRate,
dsmonMatrixTopNHCRevOctetRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per conversation
monitoring functions for High Capacity networks."
::= { dsmonGroups 14 }
END
Expires April 26, 2002 [Page 113]
Internet Draft DSMON MIB October 2001
8. Aggregation Configuration Usage Examples
This section contains an example of the steps that may be followed by a
management station to configure the objects in the dsmonAggControlGroup.
A note about these examples:
- they do not define a standard
- an agent is not obligated to support them
- a management application is not constrained by them
- the SET(object = value [, ...]) notation is
only conceptual, and is not meant to represent an actual SNMP Set
PDU.
8.1. Step 1: Unlock the Aggregation Configuration
Before any write operations to the tabular objects in this group can be
made, the aggregation configuration must be unlocked, by setting the
dsmonAggControlLocked scalar to false:
SET(dsmonAggControlLocked.0 = false(2));
8.2. Step 2: Check the Maximum number of Aggregation Groups
Make sure the desired aggregation groups have a chance of being
configured on the agent.
maxGroups = GET(dsmonAggMaxAggGroups.0);
For this example, maxGroups is greater or equal to 64.
8.3. Step 3: Check if the aggregation profiles already exist
Make sure the desired aggregation profiles have not already been
configured, or perhaps recreated after an agent restart. The following
example is oversimplified, in that the entire aggregation configuration
should actually be verified.
profile1Descr = GET(dsmonAggControlDescr.1);
profile1Owner = GET(dsmonAggControlOwner.1);
profile1Status = GET(dsmonAggControlStatus.1);
Expires April 26, 2002 [Page 114]
Internet Draft DSMON MIB October 2001
For this example, none of the aggregation profiles already exist.
8.4. Step 4: Create the Aggregation Control Entries
The management station should create one entry in the
dsmonAggControlTable for each aggregation profile to be configured on
the agent.
Steps 4, 5, and 6 are repeated for each aggregation profile to be
configured on the agent. There are 3 example aggregation profiles shown
in each of these steps.
Example 1: Each DSCP in its own aggregation group
SET(dsmonAggControlStatus.1 = createAndGo(4),
dsmonAggControlOwner.1 = "Example App 1",
dsmonAggControlDescr.1 = "1 DSCP Per Group");
Example 2: a collection of DIFFSERV PHBs.
SET(dsmonAggControlStatus.2 = createAndGo(4),
dsmonAggControlOwner.2 = "Example App 2",
dsmonAggControlDescr.2 = "June 2000 DIFFSERV PHBs");
Example 3: an aggregated collection of DIFFSERV PHBs.
SET(dsmonAggControlStatus.3 = createAndGo(4),
dsmonAggControlOwner.3 = "Example App 3",
dsmonAggControlDescr.3 = "Limited June 2000 PHBs");
8.5. Step 5: Create the Aggregation Group Descriptions
Example 1: Each DSCP in its own aggregation group One group is created
for each codepoint, for a total of 64 rows.
SET(dsmonAggGroupStatus.1.0 = createAndGo(4),
dsmonAggGroupDescr.1.0 = "DSCP 0");
SET(dsmonAggGroupStatus.1.1 = createAndGo(4),
dsmonAggGroupDescr.1.1 = "DSCP 1");
SET(dsmonAggGroupStatus.1.2 = createAndGo(4),
dsmonAggGroupDescr.1.2 = "DSCP 2");
SET(dsmonAggGroupStatus.1.3 = createAndGo(4),
dsmonAggGroupDescr.1.3 = "DSCP 3");
Expires April 26, 2002 [Page 115]
Internet Draft DSMON MIB October 2001
...
SET(dsmonAggGroupStatus.1.63 = createAndGo(4),
dsmonAggGroupDescr.1.63 = "DSCP 63");
Example 2: a collection of current DIFFSERV PHBs. One group is created
for each PHB to be monitored
SET(dsmonAggGroupStatus.2.0 = createAndGo(4),
dsmonAggGroupDescr.2.0 = "CS0");
SET(dsmonAggGroupStatus.2.1 = createAndGo(4),
dsmonAggGroupDescr.2.1 = "CS1");
SET(dsmonAggGroupStatus.2.2 = createAndGo(4),
dsmonAggGroupDescr.2.2 = "CS2");
SET(dsmonAggGroupStatus.2.3 = createAndGo(4),
dsmonAggGroupDescr.2.3 = "CS3");
SET(dsmonAggGroupStatus.2.4 = createAndGo(4),
dsmonAggGroupDescr.2.4 = "CS4");
SET(dsmonAggGroupStatus.2.5 = createAndGo(4),
dsmonAggGroupDescr.2.5 = "CS5");
SET(dsmonAggGroupStatus.2.6 = createAndGo(4),
dsmonAggGroupDescr.2.6 = "CS6");
SET(dsmonAggGroupStatus.2.7 = createAndGo(4),
dsmonAggGroupDescr.2.7 = "CS7");
SET(dsmonAggGroupStatus.2.8 = createAndGo(4),
dsmonAggGroupDescr.2.8 = "EF");
SET(dsmonAggGroupStatus.2.9 = createAndGo(4),
dsmonAggGroupDescr.2.9 = "AF11");
SET(dsmonAggGroupStatus.2.10 = createAndGo(4),
dsmonAggGroupDescr.2.10 = "AF12");
SET(dsmonAggGroupStatus.2.11 = createAndGo(4),
dsmonAggGroupDescr.2.11 = "AF13");
SET(dsmonAggGroupStatus.2.12 = createAndGo(4),
dsmonAggGroupDescr.2.12 = "AF21");
SET(dsmonAggGroupStatus.2.13 = createAndGo(4),
dsmonAggGroupDescr.2.13 = "AF22");
SET(dsmonAggGroupStatus.2.14 = createAndGo(4),
dsmonAggGroupDescr.2.14 = "AF23");
SET(dsmonAggGroupStatus.2.15 = createAndGo(4),
dsmonAggGroupDescr.2.15 = "AF31");
SET(dsmonAggGroupStatus.2.16 = createAndGo(4),
dsmonAggGroupDescr.2.16 = "AF32");
SET(dsmonAggGroupStatus.2.17 = createAndGo(4),
dsmonAggGroupDescr.2.17 = "AF33");
SET(dsmonAggGroupStatus.2.18 = createAndGo(4),
Expires April 26, 2002 [Page 116]
Internet Draft DSMON MIB October 2001
dsmonAggGroupDescr.2.18 = "AF41");
SET(dsmonAggGroupStatus.2.19 = createAndGo(4),
dsmonAggGroupDescr.2.19 = "AF42");
SET(dsmonAggGroupStatus.2.20 = createAndGo(4),
dsmonAggGroupDescr.2.20 = "AF43");
SET(dsmonAggGroupStatus.2.21 = createAndGo(4),
dsmonAggGroupDescr.2.21 = "Nonzero Default");
Example 3: an aggregated representation of current DIFFSERV PHBs. One
group is created for each aggregation to be monitored (8 rows in this
example).
SET(dsmonAggGroupStatus.3.0 = createAndGo(4),
dsmonAggGroupDescr.3.0 = "Zero CS");
SET(dsmonAggGroupStatus.3.1 = createAndGo(4),
dsmonAggGroupDescr.3.1 = "Nonzero CS");
SET(dsmonAggGroupStatus.3.2 = createAndGo(4),
dsmonAggGroupDescr.3.2 = "EF");
SET(dsmonAggGroupStatus.3.3 = createAndGo(4),
dsmonAggGroupDescr.3.3 = "AF1");
SET(dsmonAggGroupStatus.3.4 = createAndGo(4),
dsmonAggGroupDescr.3.4 = "AF2");
SET(dsmonAggGroupStatus.3.5 = createAndGo(4),
dsmonAggGroupDescr.3.5 = "AF3");
SET(dsmonAggGroupStatus.3.6 = createAndGo(4),
dsmonAggGroupDescr.3.6 = "AF4");
SET(dsmonAggGroupStatus.3.7 = createAndGo(4),
dsmonAggGroupDescr.3.7 = "Nonzero Default");
8.6. Step 6: Create the Aggregation Profile Mappings
After the dsmonAggControlEntries are activated, the associated read-
write dsmonAggProfileEntries will be created. The management station
must create 64 entries in the dsmonAggProfileTable for each aggregation
profile configured in the dsmonAggControlTable.
Example 1: Each DSCP in its own aggregation group
SET(dsmonAggGroupIndex.1.0 = 0,
dsmonAggGroupIndex.1.1 = 1,
dsmonAggGroupIndex.1.2 = 2,
dsmonAggGroupIndex.1.3 = 3,
...
dsmonAggGroupIndex.1.63 = 63);
Expires April 26, 2002 [Page 117]
Internet Draft DSMON MIB October 2001
Example 2: a collection of current DIFFSERV PHBs.
SET(dsmonAggGroupIndex.2.0 = 0, -- CS0
dsmonAggGroupIndex.2.1 = 21, -- Nonzero Default
dsmonAggGroupIndex.2.2 = 21,
dsmonAggGroupIndex.2.3 = 21,
dsmonAggGroupIndex.2.4 = 21,
dsmonAggGroupIndex.2.5 = 21,
dsmonAggGroupIndex.2.6 = 21,
dsmonAggGroupIndex.2.7 = 21,
dsmonAggGroupIndex.2.8 = 1, -- CS1
dsmonAggGroupIndex.2.9 = 21,
dsmonAggGroupIndex.2.10 = 9, -- AF11
dsmonAggGroupIndex.2.11 = 21,
dsmonAggGroupIndex.2.12 = 10, -- AF12
dsmonAggGroupIndex.2.13 = 21,
dsmonAggGroupIndex.2.14 = 11, -- AF13
dsmonAggGroupIndex.2.15 = 21,
dsmonAggGroupIndex.2.16 = 2, -- CS2
dsmonAggGroupIndex.2.17 = 21,
dsmonAggGroupIndex.2.18 = 12, -- AF21
dsmonAggGroupIndex.2.19 = 21,
dsmonAggGroupIndex.2.20 = 13, -- AF22
dsmonAggGroupIndex.2.21 = 21,
dsmonAggGroupIndex.2.22 = 14, -- AF23
dsmonAggGroupIndex.2.23 = 21,
dsmonAggGroupIndex.2.24 = 3, -- CS3
dsmonAggGroupIndex.2.25 = 21,
dsmonAggGroupIndex.2.26 = 15, -- AF31
dsmonAggGroupIndex.2.27 = 21,
dsmonAggGroupIndex.2.28 = 16, -- AF32
dsmonAggGroupIndex.2.29 = 8, -- EF
dsmonAggGroupIndex.2.30 = 17, -- AF33
dsmonAggGroupIndex.2.31 = 21,
dsmonAggGroupIndex.2.32 = 4, -- CS4
dsmonAggGroupIndex.2.33 = 21,
dsmonAggGroupIndex.2.34 = 18, -- AF41
dsmonAggGroupIndex.2.35 = 21,
dsmonAggGroupIndex.2.36 = 19, -- AF42
dsmonAggGroupIndex.2.37 = 21,
dsmonAggGroupIndex.2.38 = 20, -- AF43
dsmonAggGroupIndex.2.39 = 21,
dsmonAggGroupIndex.2.40 = 5, -- CS5
dsmonAggGroupIndex.2.41 = 21,
dsmonAggGroupIndex.2.42 = 21,
Expires April 26, 2002 [Page 118]
Internet Draft DSMON MIB October 2001
dsmonAggGroupIndex.2.43 = 21,
dsmonAggGroupIndex.2.44 = 21,
dsmonAggGroupIndex.2.45 = 21,
dsmonAggGroupIndex.2.46 = 21,
dsmonAggGroupIndex.2.47 = 21,
dsmonAggGroupIndex.2.48 = 6, -- CS6
dsmonAggGroupIndex.2.49 = 21,
dsmonAggGroupIndex.2.50 = 21,
dsmonAggGroupIndex.2.51 = 21,
dsmonAggGroupIndex.2.52 = 21,
dsmonAggGroupIndex.2.53 = 21,
dsmonAggGroupIndex.2.54 = 21,
dsmonAggGroupIndex.2.55 = 21,
dsmonAggGroupIndex.2.56 = 7, -- CS7
dsmonAggGroupIndex.2.57 = 21,
dsmonAggGroupIndex.2.58 = 21,
dsmonAggGroupIndex.2.59 = 21,
dsmonAggGroupIndex.2.60 = 21,
dsmonAggGroupIndex.2.61 = 21,
dsmonAggGroupIndex.2.62 = 21,
dsmonAggGroupIndex.2.63 = 21);
Example 3: an aggregated collection of current DIFFSERV PHBs.
SET(dsmonAggGroupIndex.3.0 = 0, -- Zero CS
dsmonAggGroupIndex.3.1 = 7, -- Nonzero Default
dsmonAggGroupIndex.3.2 = 7,
dsmonAggGroupIndex.3.3 = 7,
dsmonAggGroupIndex.3.4 = 7,
dsmonAggGroupIndex.3.5 = 7,
dsmonAggGroupIndex.3.6 = 7,
dsmonAggGroupIndex.3.7 = 7,
dsmonAggGroupIndex.3.8 = 1, -- Nonzero CS
dsmonAggGroupIndex.3.9 = 7,
dsmonAggGroupIndex.3.10 = 3, -- AF1
dsmonAggGroupIndex.3.11 = 7,
dsmonAggGroupIndex.3.12 = 3,
dsmonAggGroupIndex.3.13 = 7,
dsmonAggGroupIndex.3.14 = 3,
dsmonAggGroupIndex.3.15 = 7,
dsmonAggGroupIndex.3.16 = 1,
dsmonAggGroupIndex.3.17 = 7,
dsmonAggGroupIndex.3.18 = 4, -- AF2
dsmonAggGroupIndex.3.19 = 7,
dsmonAggGroupIndex.3.20 = 4,
Expires April 26, 2002 [Page 119]
Internet Draft DSMON MIB October 2001
dsmonAggGroupIndex.3.21 = 7,
dsmonAggGroupIndex.3.22 = 4,
dsmonAggGroupIndex.3.23 = 7,
dsmonAggGroupIndex.3.24 = 1,
dsmonAggGroupIndex.3.25 = 7,
dsmonAggGroupIndex.3.26 = 5, -- AF3
dsmonAggGroupIndex.3.27 = 7,
dsmonAggGroupIndex.3.28 = 5,
dsmonAggGroupIndex.3.29 = 2, -- EF
dsmonAggGroupIndex.3.30 = 5,
dsmonAggGroupIndex.3.31 = 7,
dsmonAggGroupIndex.3.32 = 1,
dsmonAggGroupIndex.3.33 = 7,
dsmonAggGroupIndex.3.34 = 6, -- AF4
dsmonAggGroupIndex.3.35 = 7,
dsmonAggGroupIndex.3.36 = 6,
dsmonAggGroupIndex.3.37 = 7,
dsmonAggGroupIndex.3.38 = 6,
dsmonAggGroupIndex.3.39 = 7,
dsmonAggGroupIndex.3.40 = 1,
dsmonAggGroupIndex.3.41 = 7,
dsmonAggGroupIndex.3.42 = 7,
dsmonAggGroupIndex.3.43 = 7,
dsmonAggGroupIndex.3.44 = 7,
dsmonAggGroupIndex.3.45 = 7,
dsmonAggGroupIndex.3.46 = 7,
dsmonAggGroupIndex.3.47 = 7,
dsmonAggGroupIndex.3.48 = 1,
dsmonAggGroupIndex.3.49 = 7,
dsmonAggGroupIndex.3.50 = 7,
dsmonAggGroupIndex.3.51 = 7,
dsmonAggGroupIndex.3.52 = 7,
dsmonAggGroupIndex.3.53 = 7,
dsmonAggGroupIndex.3.54 = 7,
dsmonAggGroupIndex.3.55 = 7,
dsmonAggGroupIndex.3.56 = 1,
dsmonAggGroupIndex.3.57 = 7,
dsmonAggGroupIndex.3.58 = 7,
dsmonAggGroupIndex.3.59 = 7,
dsmonAggGroupIndex.3.60 = 7,
dsmonAggGroupIndex.3.61 = 7,
dsmonAggGroupIndex.3.62 = 7,
dsmonAggGroupIndex.3.63 = 7);
Expires April 26, 2002 [Page 120]
Internet Draft DSMON MIB October 2001
8.7. Step 7: Lock the Aggregation Configuration
Before any existing collections can be activated by the agent, the
aggregation configuration must be locked, by setting the
dsmonAggControlLocked scalar to 'true'.
SET(dsmonAggControlLocked.0 = true(1));
9. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to pertain
to the implementation or use of the technology described in this
document or the extent to which any license under such rights might or
might not be available; neither does it represent that it has made any
effort to identify any such rights. Information on the IETF's
procedures with respect to rights in standards-track and standards-
related documentation can be found in BCP-11. Copies of claims of
rights made available for publication and any assurances of licenses to
be made available, or the result of an attempt made to obtain a general
license or permission for the use of such proprietary rights by
implementors or users of this specification can be obtained from the
IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary rights
which may cover technology that may be required to practice this
standard. Please address the information to the IETF Executive
Director.
10. Acknowledgements
This memo is a product of the RMONMIB WG. It is based on an Internet
Draft that was produced with a great deal of assistance from Keith
McCloghrie and Bijendra Jain.
11. References
[RFC1155]
Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
Performance Systems International, Hughes LAN Systems, May 1990.
Expires April 26, 2002 [Page 121]
Internet Draft DSMON MIB October 2001
[RFC1157]
Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, SNMP Research, Performance Systems
International, Performance Systems International, MIT Laboratory
for Computer Science, May 1990.
[RFC1212]
Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212,
Performance Systems International, Hughes LAN Systems, March 1991.
[RFC1215]
M. Rose, "A Convention for Defining Traps for use with the SNMP",
RFC 1215, Performance Systems International, March 1991.
[RFC1901]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901,
SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting,
Inc., International Network Services, January 1996.
[RFC1905]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Protocol Operations for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1905, SNMP Research,
Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc.,
International Network Services, January 1996.
[RFC1906]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco
Systems, Inc., Dover Beach Consulting, Inc., International Network
Services, January 1996.
[RFC2021]
S. Waldbusser, "Remote Network Monitoring MIB (RMON-2)", RFC 2021,
International Network Services, January 1997.
[RFC2026]
Bradner, S., "The Internet Standards Process -- Revision 3", RFC
2026, Harvard University, October, 1996.
[RFC2074]
Bierman, A., and R. Iddon, "Remote Network Monitoring MIB Protocol
Identifiers", RFC 2074, Cisco Systems, AXON Networks, Inc., January
Expires April 26, 2002 [Page 122]
Internet Draft DSMON MIB October 2001
1997.
[RFC2119]
S. Bradner, "Key words for use in RFCs to Indicate Requirement
Levels" RFC 2119, Harvard University, March 1997.
[RFC2474]
Nichols, K., Blake, S., Baker, F., and D. L. Black, "Definition of
the Differentiated Services Field (DS Field) in the IPv4 and IPv6
Headers", RFC 2474, Cisco Systems, Torrent Networking Technologies,
EMC Corporation, December, 1998.
[RFC2475]
Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z., and W.
Weiss, "An Architecture for Differentiated Services", RFC 2475,
Torrent Networking Technologies, EMC Corporation, Sun Microsystems,
Nortel UK, Bell Labs Lucent Technologies, Lucent Technologies,
December, 1998.
[RFC2570]
Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to
Version 3 of the Internet-standard Network Management Framework",
RFC 2570, SNMP Research, Inc., TIS Labs at Network Associates,
Inc., Ericsson, Cisco Systems, April 1999.
[RFC2571]
Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, April
1999.
[RFC2572]
Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, SNMP Research, Inc., Cabletron Systems,
Inc., BMC Software, Inc., IBM T. J. Watson Research, April 1999.
[RFC2573]
Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, SNMP Research, Inc., Secure Computing Corporation, Cisco
Systems, April 1999.
[RFC2574]
Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for
version 3 of the Simple Network Management Protocol (SNMPv3)", RFC
Expires April 26, 2002 [Page 123]
Internet Draft DSMON MIB October 2001
2574, IBM T. J. Watson Research, April 1999.
[RFC2575]
Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, IBM T. J. Watson Research, BMC Software, Inc.,
Cisco Systems, Inc., April 1999.
[RFC2578]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Structure of Management Information Version 2
(SMIv2)", RFC 2578, STD 58, Cisco Systems, SNMPinfo, TU
Braunschweig, SNMP Research, First Virtual Holdings, International
Network Services, April 1999.
[RFC2579]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Textual Conventions for SMIv2", RFC 2579, STD
58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First
Virtual Holdings, International Network Services, April 1999.
[RFC2580]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Conformance Statements for SMIv2", RFC 2580,
STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research,
First Virtual Holdings, International Network Services, April 1999.
[RFC2856]
Bierman, A., McCloghrie, K., and R. Presuhn, "Textual Conventions
for Additional High Capacity Data Types", RFC 2856, June, 2000.
12. Security Considerations
In order to implement this MIB, a probe must capture all packets on the
locally-attached network, including packets between third parties.
These packets are analyzed to collect network addresses, protocol usage
information, and conversation statistics. Data of this nature may be
considered sensitive in some environments. In such environments the
administrator may wish to restrict SNMP access to the probe.
There are a number of management objects defined in this MIB that have a
MAX-ACCESS clause of read-write and/or read-create. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
Expires April 26, 2002 [Page 124]
Internet Draft DSMON MIB October 2001
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and GET/SET
(read/change/create/delete) the objects in this MIB.
It is recommended that the implementors consider the security features
as provided by the SNMPv3 framework. Specifically, the use of the User-
based Security Model RFC 2574 [RFC2574] and the View-based Access
Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity
giving access to an instance of this MIB, is properly configured to give
access to the objects only to those principals (users) that have
legitimate rights to indeed GET or SET (change/create/delete) them.
13. Author's Address
Andy Bierman
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA USA 95134
Phone: +1 408-527-3711
Email: abierman@cisco.com
Expires April 26, 2002 [Page 125]
Internet Draft DSMON MIB October 2001
14. Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it or
assist in its implementation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are included
on all such copies and derivative works. However, this document itself
may not be modified in any way, such as by removing the copyright notice
or references to the Internet Society or other Internet organizations,
except as needed for the purpose of developing Internet standards in
which case the procedures for copyrights defined in the Internet
Standards process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT
INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
Expires April 26, 2002 [Page 126]
