Internet Draft                                            Anwar Siddiqui
                                                              Avaya Inc.
                                                           Dan Romascanu
                                                                   Avaya
                                                       Eugene Golovinsky
                                                            BMC Software
                                                        12 February 2006


                 Real-time Application Quality of Service
                        Monitoring (RAQMON) MIB

              <draft-ietf-rmonmib-raqmon-mib-12.txt>


Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress".

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/1id-abstracts.html

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   The document proposes an extension to the Remote Monitoring MIB - RFC
   2819.  In particular, it describes managed objects used for real-time
   application Quality of Service (QoS) monitoring.

   Distribution of this memo is unlimited.




RMON MIB WG                Expires August 2006                  [Page 1]


INTERNET DRAFT                 RAQMON MIB                  February 2006


Table of Contents

   Status of this Memo                                             1
   Abstract                                                        1
    1 Introduction                                                 2
    2 The Internet-Standard Management Framework                   2
    3 RAQMON Framework                                             2
    4 Structure of the RAQMON MIB                                  3
    5 RAQMON MIB Definitions                                       3
    6 Security Considerations                                     34
    7 IANA Considerations                                         36
    8 Acknowledgements                                            36
    Normative References                                          36
    Informative References                                        37
    Author's Address                                              37
    Full Copyright Statement                                      38
    IPR Disclosure Acknowledgement                                38

1.  Introduction

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it extends [RFC2819] with managed objects used for
   real-time application QOS monitoring.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].


2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].


3.  RAQMON Framework




RMON MIB WG                Expires August 2006                  [Page 2]


INTERNET DRAFT                 RAQMON MIB                  February 2006


   As outlined in [RAQMON-FRAMEWORK], the RAQMON framework is based on
   three entities:

      - RAQMON Data Source (RDS)

      - RAQMON Report Collector (RRC)

      - RAQMON MIB Structure


   The RAQMON MIB describes information passed between RRCs and a RAQMON
   Application ("RAQMON manager").

4.  Structure of the RAQMON MIB

   The RAQMON MIB module is composed of three MIB groups: raqmonSession,
   raqmonException, and raqmonConfig.

   The raqmonSession MIB group incorporates the following tables:
      - The raqmonParticpantTable contains information about
      participants in open and closed (terminated) sessions, including
      parameters of the sessions they are involved in, aggregated since
      the beginning of the session.
      - The raqmonQosTable contains historical information about QoS
      during sessions. The set of parameters represented in this table
      is more restricted, but it includes historical per RAQMON report
      information.
      - The raqmonParticpantAddrTable maps participant addresses into
      the indices of the raqmonParticpantTable. This table allows
      management applications to find entries sorted by
      raqmonParticipantAddr rather than raqmonParticipantStartDate.

   The raqmonException MIB group includes a table of filters that
   trigger notifications for sessions with poor QoS.

   The raqmonConfig MIB group includes object that define the
   configuration of the RAQMON Report Collector.

   This MIB module MUST be implemented by RAQMON Report Collectors.

   A separate MIB module is defined in [RAQMON-PDU] for mapping the
   RAQMON PDUs onto an SNMP transport.  The MIB module defined in
   [RAQMON-PDU] is normally implemented by RAQMON Data Sources (RDS).

5.  RAQMON MIB Definitions

   The following MIB module IMPORTS definitions from the following:
         SNMPv2-SMI [RFC2578]



RMON MIB WG                Expires August 2006                  [Page 3]


INTERNET DRAFT                 RAQMON MIB                  February 2006


         SNMPv2-TC [RFC2579]
         SNMPv2-CONF [RFC2580]
         RMON-MIB [RFC2819]
         SNMP-FRAMEWORK-MIB [RFC3411]
         INET-ADDRESS-MIB [RFC4001]

   It also uses REFERENCE clauses to refer to [RAQMON-FRAMEWORK].

   It also mentions [RFC3737] with respect to the MODULE-IDENTITY OID
   allocation.



   RAQMON-MIB DEFINITIONS ::= BEGIN

       IMPORTS
           OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE
               FROM SNMPv2-CONF
           Integer32, Unsigned32,
           Gauge32, Counter32, OBJECT-TYPE,
           MODULE-IDENTITY, NOTIFICATION-TYPE
               FROM SNMPv2-SMI
           InetAddressType, InetAddress, InetPortNumber
               FROM INET-ADDRESS-MIB
                    SnmpAdminString
           FROM SNMP-FRAMEWORK-MIB
           rmon
               FROM RMON-MIB
           RowStatus, TruthValue, DateAndTime, RowPointer
               FROM SNMPv2-TC;

       raqmonMIB MODULE-IDENTITY
           LAST-UPDATED "200602120000Z"     -- February 12, 2006
           ORGANIZATION
               "IETF RMON MIB Working Group"
           CONTACT-INFO
               "WG Charter:
                http://www.ietf.org/html.charters/rmonmib-charter.html

                Mailing lists:
                    General Discussion: rmonmib@ietf.org
                    To Subscribe: rmonmib-requests@ietf.org
                    In Body: subscribe your_email_address

                Chair: Andy Bierman
                       Email: ietf@andybierman.com

                Editor: Dan Romascanu



RMON MIB WG                Expires August 2006                  [Page 4]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                        Avaya
                        Email:  dromasca@avaya.com"
           DESCRIPTION
               "Real-Time Application QoS Monitoring MIB.

                Copyright (c) The Internet Society (2006).
                This version of this MIB module is part of
                RFC yyyy; See the RFC itself for full legal notices."

   -- RFC Ed.: replace yyyy with the actual RFC
   -- number & remove this notice.

           REVISION    "200602120000Z"
           DESCRIPTION
               "Initial version, published as RFC yyyy."
   -- RFC-Editor assigns yyyy
           ::= { rmon 31 }

   -- This OID allocation conforms to [RFC3737]


   --
   -- Node definitions
   --
       raqmonNotifications OBJECT IDENTIFIER ::= { raqmonMIB 0 }

       raqmonSessionAlarm NOTIFICATION-TYPE
           OBJECTS { raqmonParticipantAddr,
               raqmonParticipantName,
               raqmonParticipantPeerAddrType,
               raqmonParticipantPeerAddr,
               raqmonQoSEnd2EndNetDelay,
               raqmonQoSInterArrivalJitter,
               raqmonQosLostPackets,
               raqmonQosRcvdPackets }
           STATUS current
           DESCRIPTION
               "A notification generated by an entry in the
               raqmonSessionExceptionTable."
           ::= { raqmonNotifications 1 }


       raqmonMIBObjects OBJECT IDENTIFIER ::= { raqmonMIB 1 }

       raqmonSession OBJECT IDENTIFIER ::= { raqmonMIBObjects 1 }

       raqmonParticipantTable OBJECT-TYPE
           SYNTAX SEQUENCE OF RaqmonParticipantEntry



RMON MIB WG                Expires August 2006                  [Page 5]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "This table contains information about participants in
                both active and closed (terminated) sessions."
           ::= { raqmonSession 1 }

       raqmonParticipantEntry OBJECT-TYPE
           SYNTAX RaqmonParticipantEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "Each row contains information for a single session
                (application) run by one participant.
                Indexation by the start time of the session aims
                easing sorting by management applications. Agents MUST
                NOT report identical start time for any two sessions
                on the same host.
                Rows are removed for inactive sessions
                when implementation-specific age or space limits are
                reached."
           INDEX { raqmonParticipantStartDate, raqmonParticipantIndex }
           ::= { raqmonParticipantTable 1 }

       RaqmonParticipantEntry ::=
           SEQUENCE {
               raqmonParticipantStartDate     DateAndTime,
               raqmonParticipantIndex         Unsigned32,
               raqmonParticipantReportCaps    BITS,
               raqmonParticipantAddrType      InetAddressType,
               raqmonParticipantAddr          InetAddress,
               raqmonParticipantSendPort      InetPortNumber,
               raqmonParticipantRecvPort      InetPortNumber,
               raqmonParticipantSetupDelay    Integer32,
               raqmonParticipantName          SnmpAdminString,
               raqmonParticipantAppName       SnmpAdminString,
               raqmonParticipantQosCount      Gauge32,
               raqmonParticipantEndDate       DateAndTime,
               raqmonParticipantDestPayloadType  Integer32,
               raqmonParticipantSrcPayloadType   Integer32,
               raqmonParticipantActive        TruthValue,
               raqmonParticipantPeer          RowPointer,
               raqmonParticipantPeerAddrType  InetAddressType,
               raqmonParticipantPeerAddr      InetAddress,
               raqmonParticipantSrcL2Priority     Integer32,
               raqmonParticipantDestL2Priority    Integer32,
               raqmonParticipantSrcDSCP       Integer32,
               raqmonParticipantDestDSCP      Integer32,



RMON MIB WG                Expires August 2006                  [Page 6]


INTERNET DRAFT                 RAQMON MIB                  February 2006


               raqmonParticipantCpuMean       Integer32,
               raqmonParticipantCpuMin        Integer32,
               raqmonParticipantCpuMax        Integer32,
               raqmonParticipantMemoryMean    Integer32,
               raqmonParticipantMemoryMin     Integer32,
               raqmonParticipantMemoryMax     Integer32,
               raqmonParticipantNetRTTMean    Integer32,
               raqmonParticipantNetRTTMin     Integer32,
               raqmonParticipantNetRTTMax     Integer32,
               raqmonParticipantIAJitterMean  Integer32,
               raqmonParticipantIAJitterMin   Integer32,
               raqmonParticipantIAJitterMax   Integer32,
               raqmonParticipantIPDVMean      Integer32,
               raqmonParticipantIPDVMin       Integer32,
               raqmonParticipantIPDVMax       Integer32,
               raqmonParticipantNetOwdMean    Integer32,
               raqmonParticipantNetOwdMin     Integer32,
               raqmonParticipantNetOwdMax     Integer32,
               raqmonParticipantAppDelayMean  Integer32,
               raqmonParticipantAppDelayMin   Integer32,
               raqmonParticipantAppDelayMax   Integer32,
               raqmonParticipantPacketsRcvd   Integer32,
               raqmonParticipantPacketsSent   Integer32,
               raqmonParticipantOctetsRcvd    Integer32,
               raqmonParticipantOctetsSent    Integer32,
               raqmonParticipantLostPackets   Integer32,
               raqmonParticipantLostPacketsFrct  Integer32,
               raqmonParticipantDiscards      Integer32,
               raqmonParticipantDiscardsFrct  Integer32
            }

       raqmonParticipantStartDate OBJECT-TYPE
           SYNTAX DateAndTime
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "The date and time of this entry.
                It will be the date and time
                of the first report received."
           ::= { raqmonParticipantEntry 1 }

       raqmonParticipantIndex OBJECT-TYPE
           SYNTAX Unsigned32 (1..2147483647)
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "The index of the conceptual row which is for SNMP
                purposes only and has no relation to any protocol value.



RMON MIB WG                Expires August 2006                  [Page 7]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                There is no requirement that these rows be created or
                maintained sequentially.  The index will be unique for a
                particular date and time."
           ::= { raqmonParticipantEntry 2 }

       raqmonParticipantReportCaps   OBJECT-TYPE
           SYNTAX      BITS {
               raqmonPartRepDsrcName(0),
               raqmonPartRepRecvName(1),
               raqmonPartRepDsrcPort(2),
               raqmonPartRepRecvPort(3),
               raqmonPartRepSetupTime(4),
               raqmonPartRepSetupDelay(5),
               raqmonPartRepSessionDuration(6),
               raqmonPartRepSetupStatus(7),
               raqmonPartRepRTEnd2EndNetDelay(8),
               raqmonPartRepOWEnd2EndNetDelay(9),
               raqmonPartApplicationDelay(10),
               raqmonPartRepIAJitter(11),
               raqmonPartRepIPDV(12),
               raqmonPartRepRcvdPackets(13),
               raqmonPartRepRcvdOctets(14),
               raqmonPartRepSentPackets(15),
               raqmonPartRepSentOctets(16),
               raqmonPartRepCumPacketsLoss(17),
               raqmonPartRepFractionPacketsLoss(18),
               raqmonPartRepCumDiscards(19),
               raqmonPartRepFractionDiscards(20),
               raqmonPartRepSrcPayloadType(21),
               raqmonPartRepDestPayloadType(22),
               raqmonPartRepSrcLayer2Priority(23),
               raqmonPartRepSrcTosDscp(24),
               raqmonPartRepDestLayer2Priority(25),
               raqmonPartRepDestTosDscp(26),
               raqmonPartRepCPU(27),
               raqmonPartRepMemory(28),
               raqmonPartRepAppName(29)
               }
           MAX-ACCESS  read-only
           STATUS      current
           DESCRIPTION
               "The Report capabilities of the participant, as
                perceived by the Collector.

                If the participant can report the Data Source Name
                as defined in [RAQMON-FRAMEWORK], Section 5.3,
                then the raqmonPartRepDsrcName bit will be set.




RMON MIB WG                Expires August 2006                  [Page 8]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                If the participant can report the Receiver Name
                as defined in [RAQMON-FRAMEWORK], Section 5.4,
                then the raqmonPartRepRecvName bit will be set.

                If the participant can report the Data Source Port
                as defined in [RAQMON-FRAMEWORK], Section 5.5,
                then the raqmonPartRepDsrcPort bit will be set.

                If the participant can report the Receiver Port
                as defined in [RAQMON-FRAMEWORK], Section 5.6,
                then the raqmonPartRepRecvPort bit will be set.

                If the participant can report the Session Setup Time
                as defined in [RAQMON-FRAMEWORK], Section 5.7,
                then the raqmonPartRepSetupTime bit will be set.

                If the participant can report the Session Setup Delay
                as defined in [RAQMON-FRAMEWORK], Section 5.8,
                then the raqmonPartRepSetupDelay bit will be set.

                If the participant can report the Session Duration
                as defined in [RAQMON-FRAMEWORK], Section 5.9,
                then the raqmonPartRepSessionDuration bit will be set.

                If the participant can report the Setup Status
                as defined in [RAQMON-FRAMEWORK], Section 5.10,
                then the raqmonPartRepSetupStatus bit will be set.

                If the participant can report the Round-Trip
                End-to-end Network Delay
                as defined in [RAQMON-FRAMEWORK], Section 5.11,
                then the raqmonPartRepRTEnd2EndNetDelay bit will be set.

                If the participant can report the One-way
                End-to-end Network Delay
                as defined in [RAQMON-FRAMEWORK], Section 5.12,
                then the raqmonPartRepOWEnd2EndNetDelay bit will be set.

                If the participant can report the Application Delay
                as defined in [RAQMON-FRAMEWORK], Section 5.13,
                then the raqmonPartApplicationDelay bit will be set.

                If the participant can report the Inter-Arrival Jitter
                as defined in [RAQMON-FRAMEWORK], Section 5.14,
                then the raqmonPartRepIAJitter bit will be set.

                If the participant can report the IP Packet Delay
                Variation as defined in [RAQMON-FRAMEWORK], Section



RMON MIB WG                Expires August 2006                  [Page 9]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                5.15, then the raqmonPartRepIPDV bit will be set.

                If the participant can report the number of application
                packets received
                as defined in [RAQMON-FRAMEWORK], Section 5.16,
                then the raqmonPartRepRcvdPackets bit will be set.

                If the participant can report the number of application
                octets received
                as defined in [RAQMON-FRAMEWORK], Section 5.17,
                then the raqmonPartRepRcvdOctets bit will be set.

                If the participant can report the number of application
                packets sent
                as defined in [RAQMON-FRAMEWORK], Section 5.18,
                then the raqmonPartRepSentPackets bit will be set.

                If the participant can report the number of application
                octets sent
                as defined in [RAQMON-FRAMEWORK], Section 5.19,
                then the raqmonPartRepSentOctets bit will be set.

                If the participant can report the number of
                cumulative packets lost
                as defined in [RAQMON-FRAMEWORK], Section 5.20,
                then the raqmonPartRepCumPacketsLoss bit will be set.

                If the participant can report the fraction of packets
                loss as defined in [RAQMON-FRAMEWORK], Section 5.21,
                then the raqmonPartRepFractionPacketsLoss bit will be
                set.

                If the participant can report the number of
                cumulative discards
                as defined in [RAQMON-FRAMEWORK], Section 5.22,
                then the raqmonPartRepCumDiscards bit will be set.

                If the participant can report the fraction of discards
                as defined in [RAQMON-FRAMEWORK], Section 5.23,
                then the raqmonPartRepFractionDiscards bit will be set.

                If the participant can report the Source Payload Type
                as defined in [RAQMON-FRAMEWORK], Section 5.24,
                then the raqmonPartRepSrcPayloadType bit will be set.

                If the participant can report the Destination Payload
                Type as defined in [RAQMON-FRAMEWORK], Section 5.25,
                then the raqmonPartRepDestPayloadType bit will be set.



RMON MIB WG                Expires August 2006                 [Page 10]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                If the participant can report the Source layer 2
                Priority as defined in [RAQMON-FRAMEWORK], Section 5.26,
                then the raqmonPartRepSrcLayer2Priority bit will be set.

                If the participant can report the Source DSCP/ToS value
                as defined in [RAQMON-FRAMEWORK], Section 5.27,
                then the raqmonPartRepSrcToSDscp bit will be set.

                If the participant can report the Destination layer 2
                Priority as defined in [RAQMON-FRAMEWORK], Section 5.28,
                then the raqmonPartRepDestLayer2Priority bit will be
                set.

                If the participant can report the Destination DSCP/ToS
                Value as defined in [RAQMON-FRAMEWORK], Section 5.29,
                then the raqmonPartRepDestToSDscp bit will be set.


                If the participant can report the CPU utilization
                as defined in [RAQMON-FRAMEWORK], Section 5.30,
                then the raqmonPartRepCPU bit will be set.

                If the participant can report the memory utilization
                as defined in [RAQMON-FRAMEWORK], Section 5.31,
                then the raqmonPartRepMemory bit will be set.

                If the participant can report the Application Name
                as defined in [RAQMON-FRAMEWORK], Section 5.32,
                then the raqmonPartRepAppName bit will be set.

                The capability of reporting of a specific metric
                does not mandate that the metric must be reported
                permanently by the data source to the respective
                collector. Some data sources MAY be configured not
                to send a metric, or some metrics may not be relevant
                to the specific application."
               ::= { raqmonParticipantEntry 3 }

       raqmonParticipantAddrType OBJECT-TYPE
           SYNTAX InetAddressType
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The type of the Internet address of the participant for
                this session."
           ::= { raqmonParticipantEntry 4 }

      raqmonParticipantAddr OBJECT-TYPE



RMON MIB WG                Expires August 2006                 [Page 11]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           SYNTAX InetAddress
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The Internet Address of the participant for this
                session. Formatting of this object is determined
                by the value of raqmonParticipantAddrType."
           ::= { raqmonParticipantEntry 5 }

      raqmonParticipantSendPort OBJECT-TYPE
           SYNTAX InetPortNumber
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Port from which session data is sent.
                If the value was not reported to the collector,
                this object will have the value 0."
           REFERENCE
               "Section 5.5 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 6 }

       raqmonParticipantRecvPort OBJECT-TYPE
           SYNTAX InetPortNumber
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Port on which session data is received.
                If the value was not reported to the collector,
                this object will have the value 0."
           REFERENCE
               "Section 5.6 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 7 }

       raqmonParticipantSetupDelay OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Session setup time.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.8 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 8 }

       raqmonParticipantName OBJECT-TYPE
           SYNTAX SnmpAdminString



RMON MIB WG                Expires August 2006                 [Page 12]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The data source name for the participant."
           REFERENCE
               "Section 5.3 of the [RAQMON-FRAMEWORK]"
          ::= { raqmonParticipantEntry 9 }

       raqmonParticipantAppName OBJECT-TYPE
           SYNTAX SnmpAdminString
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "A string giving the name and possibly the version
                of the application generating the stream, e.g.,
                'videotool 1.2.'

                This information may be useful for debugging purposes
                and is similar to the Mailer or Mail-System-Version SMTP
                headers.  The tool value is expected to remain constant
                for the duration of the session."
           REFERENCE
               "Section 5.32 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 10 }

       raqmonParticipantQosCount OBJECT-TYPE
           SYNTAX Gauge32
           UNITS  "entries"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The current number of entries in the raqmonQosTable
                for this participant and session."
           ::= { raqmonParticipantEntry 11 }

       raqmonParticipantEndDate OBJECT-TYPE
           SYNTAX DateAndTime
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The date and time of the most recent report received."
           ::= { raqmonParticipantEntry 12 }

       raqmonParticipantDestPayloadType OBJECT-TYPE
           SYNTAX Integer32 (-1|0..127)
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION



RMON MIB WG                Expires August 2006                 [Page 13]


INTERNET DRAFT                 RAQMON MIB                  February 2006


               "Destination Payload Type.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "RFC 3551 and Section 5.25 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 13 }

       raqmonParticipantSrcPayloadType OBJECT-TYPE
           SYNTAX Integer32 (-1|0..127)
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Source Payload Type.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "RFC 3551 and Section 5.24 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 14 }

       raqmonParticipantActive OBJECT-TYPE
           SYNTAX TruthValue
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Value 'true' indicates that the session
                       for this participant is active (open).
                Value 'false' indicates that the session
                is closed (terminated)."
           ::= { raqmonParticipantEntry 15 }

       raqmonParticipantPeer OBJECT-TYPE
           SYNTAX RowPointer
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The pointer to the corresponding entry in this table for
                the other peer participant.  If there is no such entry
                in the particpant table of the collector represented by
                this SNMP agent, then the value will be { 0 0 }.
               "
           ::= { raqmonParticipantEntry 16 }

       raqmonParticipantPeerAddrType OBJECT-TYPE
           SYNTAX InetAddressType
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The type of the Internet address of the peer participant



RMON MIB WG                Expires August 2006                 [Page 14]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                for this session."
           ::= { raqmonParticipantEntry 17 }

      raqmonParticipantPeerAddr OBJECT-TYPE
           SYNTAX InetAddress
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The Internet Address of the peer participant for this
                session. Formatting of this object is determined by
                the value of raqmonParticipantPeerAddrType."
           ::= { raqmonParticipantEntry 18 }

      raqmonParticipantSrcL2Priority OBJECT-TYPE
           SYNTAX Integer32 (-1|0..7)
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Source Layer 2 priority.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.26 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 19 }

       raqmonParticipantDestL2Priority OBJECT-TYPE
           SYNTAX Integer32 (-1|0..7)
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Destination Layer 2 priority.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.28 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 20 }

       raqmonParticipantSrcDSCP OBJECT-TYPE
           SYNTAX Integer32 (-1|0..63)
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Source Layer 3 DSCP value.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.27 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 21 }



RMON MIB WG                Expires August 2006                 [Page 15]


INTERNET DRAFT                 RAQMON MIB                  February 2006


       raqmonParticipantDestDSCP OBJECT-TYPE
           SYNTAX Integer32  (-1|0..63)
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Destination Layer 3 DSCP value"
           REFERENCE
               "Section 5.29 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 22 }

       raqmonParticipantCpuMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean CPU utilization.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.30 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 23 }

       raqmonParticipantCpuMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum CPU utilization.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.30 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 24 }

       raqmonParticipantCpuMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximum CPU utilization.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.30 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 25 }



RMON MIB WG                Expires August 2006                 [Page 16]


INTERNET DRAFT                 RAQMON MIB                  February 2006


       raqmonParticipantMemoryMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean memory utilization.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.31 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 26 }

       raqmonParticipantMemoryMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum memory utilization.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.31 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 27 }

       raqmonParticipantMemoryMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximum memory utilization.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.31 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 28 }

       raqmonParticipantNetRTTMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean round trip end-to-end network
                delay over the entire session.
                If the value was not reported to the collector,



RMON MIB WG                Expires August 2006                 [Page 17]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                this object will have the value -1."
           REFERENCE
               "Section 5.11 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 29 }

       raqmonParticipantNetRTTMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum round trip end-to-end network delay
                over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.11 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 30 }

       raqmonParticipantNetRTTMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximum round trip end-to-end network delay
                over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.11 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 31 }

       raqmonParticipantIAJitterMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean inter-arrival jitter over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.14 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 32 }

       raqmonParticipantIAJitterMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)



RMON MIB WG                Expires August 2006                 [Page 18]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum inter-arrival jitter over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.14 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 33 }

       raqmonParticipantIAJitterMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximim inter-arrival jitter over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.14 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 34 }

       raqmonParticipantIPDVMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean IP packet delay variation over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.15 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 35 }

       raqmonParticipantIPDVMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum IP packet delay variation over the entire
                session. If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.15 of the [RAQMON-FRAMEWORK]"



RMON MIB WG                Expires August 2006                 [Page 19]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           ::= { raqmonParticipantEntry 36 }

       raqmonParticipantIPDVMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximim IP packet delay variation over the entire
                session. If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.15 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 37 }

       raqmonParticipantNetOwdMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean Network one-way delay over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.12 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 38 }

       raqmonParticipantNetOwdMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum Network one-way delay over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.12 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 39 }

       raqmonParticipantNetOwdMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximim Network one-way delay over the entire session.



RMON MIB WG                Expires August 2006                 [Page 20]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.1 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 40 }

       raqmonParticipantAppDelayMean OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Mean application delay over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.13 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 41 }

       raqmonParticipantAppDelayMin OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Minimum application delay over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.13 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 42 }

       raqmonParticipantAppDelayMax OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Maximum application delay over the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.13 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 43 }

       raqmonParticipantPacketsRcvd OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "packets"



RMON MIB WG                Expires August 2006                 [Page 21]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of packets received for the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.16 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 44 }

       raqmonParticipantPacketsSent OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "packets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of packets sent for the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.17 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 45 }

       raqmonParticipantOctetsRcvd OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "Octets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of Octets received for the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.18 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 46 }

       raqmonParticipantOctetsSent OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "Octets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of Octets sent for the entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.19 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 47 }



RMON MIB WG                Expires August 2006                 [Page 22]


INTERNET DRAFT                 RAQMON MIB                  February 2006


       raqmonParticipantLostPackets OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "packets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of packets lost by this receiver for the entire
                session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.20 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 48 }

       raqmonParticipantLostPacketsFrct OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Fraction of lost packets out of total packets received.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.21 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 49 }

       raqmonParticipantDiscards OBJECT-TYPE
           SYNTAX Integer32 (-1|0..2147483647)
           UNITS  "packets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of packets discarded by this receiver for the
                entire session.
                If the value was not reported to the collector,
                this object will have the value -1."
           REFERENCE
               "Section 5.22 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 50 }

       raqmonParticipantDiscardsFrct OBJECT-TYPE
           SYNTAX Integer32 (-1|0..100)
           UNITS  "percents"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Fraction of discarded packets out of total packets



RMON MIB WG                Expires August 2006                 [Page 23]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                received. If the value was not reported to the
                collector, this object will have the value -1."
           REFERENCE
               "Section 5.23 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonParticipantEntry 51 }




    raqmonQosTable OBJECT-TYPE
           SYNTAX SEQUENCE OF RaqmonQosEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "Table of historical information about quality of service
                data during sessions."
           ::= { raqmonSession 2 }

       raqmonQosEntry OBJECT-TYPE
           SYNTAX RaqmonQosEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "Each entry contains information from a single RAQMON
                packet, related to a single session
                (application) run by one participant.
                Indexation by the start time of the session aims
                easing sorting by management applications. Agents MUST
                NOT report identical start time for any two sessions
                on the same host.
                Rows are removed for inactive sessions when
                implementation-specific time or space limits are
                reached."
           INDEX { raqmonParticipantStartDate,
                   raqmonParticipantIndex,
                   raqmonQosTime }
           ::= { raqmonQosTable 1 }

       RaqmonQosEntry ::=
           SEQUENCE {
               raqmonQosTime          Unsigned32,
               raqmonQoSEnd2EndNetDelay           Integer32,
               raqmonQoSInterArrivalJitter        Integer32,
               raqmonQosRcvdPackets   Integer32,
               raqmonQosRcvdOctets    Integer32,
               raqmonQosSentPackets   Integer32,
               raqmonQosSentOctets    Integer32,
               raqmonQosLostPackets   Integer32,



RMON MIB WG                Expires August 2006                 [Page 24]


INTERNET DRAFT                 RAQMON MIB                  February 2006


               raqmonQosSessionStatus SnmpAdminString
               }

       raqmonQosTime OBJECT-TYPE
           SYNTAX Unsigned32 (0..2147483647)
           UNITS  "seconds"
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "Time of this entry measured from the start of the
                corresponding participant session.
               "
           ::= { raqmonQosEntry 1 }

       raqmonQoSEnd2EndNetDelay OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The round trip time.
                Will contain the previous value if there was no report
                for this time, or -1 if the value has never
                been reported.
               "
           REFERENCE
               "Section 5.11 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonQosEntry 2 }

       raqmonQoSInterArrivalJitter OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "milliseconds"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "An estimate of delay variation as observed by this
                receiver.  Will contain the previous value if there
                was no report for this time, or -1 if the value
                has never been reported.
               "
           REFERENCE
               "Section 5.14 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonQosEntry 3 }

       raqmonQosRcvdPackets OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "packets"
           MAX-ACCESS read-only



RMON MIB WG                Expires August 2006                 [Page 25]


INTERNET DRAFT                 RAQMON MIB                  February 2006


           STATUS current
           DESCRIPTION
               "Count of packets received by this receiver since the
                previous entry. Will contain the previous value if there
                was no report for this time, or -1 if the value
                has never been reported.
               "
           REFERENCE
               "Section 5.16 of the [RAQMON-FRAMEWORK]"
       ::= { raqmonQosEntry 4 }

       raqmonQosRcvdOctets OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "octets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of octets received by this receiver since the
                previous report. Will contain the previous value if
                there was no report for this time, or -1 if the value
                has never been reported.
               "
               REFERENCE
                     "Section 5.18 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonQosEntry 5 }

       raqmonQosSentPackets OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "packets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of packets sent since the previous report.
                Will contain the previous value if there
                was no report for this time, or -1 if the value
                has never been reported.
               "
          REFERENCE
              "Section 5.17 of the [RAQMON-FRAMEWORK]"
       ::= { raqmonQosEntry 6 }

       raqmonQosSentOctets OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "octets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of octets sent since the previous report.



RMON MIB WG                Expires August 2006                 [Page 26]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                Will contain the previous value if there
                was no report for this time, or -1 if the value
                has never been reported.
               "
           REFERENCE
               "Section 5.19 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonQosEntry 7 }

       raqmonQosLostPackets OBJECT-TYPE
           SYNTAX Integer32 (-1 | 0..2147483647)
           UNITS  "packets"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "A count of packets lost as observed by this receiver
                since the Will contain the previous value if there
                was no report for this time, or -1 if the value
                has never been reported.
               "
           REFERENCE
               "Section 5.20 of the [RAQMON-FRAMEWORK]"
       ::= { raqmonQosEntry 8 }

       raqmonQosSessionStatus OBJECT-TYPE
           SYNTAX SnmpAdminString
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The session status.  Will contain the previous value
                if there was no report for this time or the zero length
                string if no value was ever reported."
           REFERENCE
               "Section 5.10 of the [RAQMON-FRAMEWORK]"
           ::= { raqmonQosEntry 9 }


       raqmonParticipantAddrTable OBJECT-TYPE
           SYNTAX SEQUENCE OF RaqmonParticipantAddrEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "Maps raqmonParticipantAddr to the index of the
                raqmonParticipantTable.  This table allows
                management applications to find entries
                sorted by raqmonParticipantAddr rather than
                raqmonParticipantStartDate."
           ::= { raqmonSession 3 }




RMON MIB WG                Expires August 2006                 [Page 27]


INTERNET DRAFT                 RAQMON MIB                  February 2006


       raqmonParticipantAddrEntry OBJECT-TYPE
           SYNTAX RaqmonParticipantAddrEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "Each entry corresponds to exactly one entry in the
                raqmonParticipantEntry - the entry containing the
                index pair raqmonParticipantStartDate,
                raqmonParticipantIndex.

                Note that there is no concern about the indexation of
                this table exceeding the limits defined by RFC 2578
                Section 3.5. According to [RAQMON-FRAMEWORK], Section
                5.1, only IPv4 and IPv6 addresses can be reported as
                participant addresses."
           INDEX { raqmonParticipantAddrType,
                   raqmonParticipantAddr,
                   raqmonParticipantStartDate,
                   raqmonParticipantIndex }
           ::= { raqmonParticipantAddrTable 1 }

       RaqmonParticipantAddrEntry ::=
           SEQUENCE { raqmonParticipantAddrEndDate DateAndTime }

       raqmonParticipantAddrEndDate OBJECT-TYPE
           SYNTAX DateAndTime
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The value of raqmonParticipantEndDate for the
                corresponding raqmonParticipantEntry."
           ::= { raqmonParticipantAddrEntry 1 }


       raqmonException OBJECT IDENTIFIER ::= { raqmonMIBObjects 2 }

       raqmonSessionExceptionTable OBJECT-TYPE
           SYNTAX SEQUENCE OF RaqmonSessionExceptionEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "This table defines thresholds for management
                station to get notifications about sessions that
                encountered poor quality of service.

                The information in this table MUST be persistent
                across agent reboots."
           ::= { raqmonException 2 }



RMON MIB WG                Expires August 2006                 [Page 28]


INTERNET DRAFT                 RAQMON MIB                  February 2006


       raqmonSessionExceptionEntry OBJECT-TYPE
           SYNTAX RaqmonSessionExceptionEntry
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "A conceptual row in the raqmonSessionExceptionTable."
           INDEX { raqmonSessionExceptionIndex }
           ::= { raqmonSessionExceptionTable 1 }

       RaqmonSessionExceptionEntry ::=
           SEQUENCE {
               raqmonSessionExceptionIndex                Unsigned32,
               raqmonSessionExceptionIAJitterThreshold    Unsigned32,
               raqmonSessionExceptionNetRTTThreshold      Unsigned32,
               raqmonSessionExceptionLostPacketsThreshold Unsigned32,
               raqmonSessionExceptionRowStatus            RowStatus
               }

       raqmonSessionExceptionIndex OBJECT-TYPE
           SYNTAX Unsigned32 (1..65535)
           MAX-ACCESS not-accessible
           STATUS current
           DESCRIPTION
               "An index that uniquely identifies an
                entry in the raqmonSessionExceptionTable.
                Management applications can determine unused indices
                by performing GetNext or GetBulk operations on the
                Table."
           ::= { raqmonSessionExceptionEntry 2 }

       raqmonSessionExceptionIAJitterThreshold OBJECT-TYPE
           SYNTAX Unsigned32
           UNITS  "milliseconds"
           MAX-ACCESS read-create
           STATUS current
           DESCRIPTION
               "Threshold for jitter.
                The value during a session must be greater than or
                equal to this value for an exception to be created."
           ::= { raqmonSessionExceptionEntry 3 }

       raqmonSessionExceptionNetRTTThreshold OBJECT-TYPE
           SYNTAX Unsigned32
           UNITS  "milliseconds"
           MAX-ACCESS read-create
           STATUS current
           DESCRIPTION
               "Threshold for round trip time.



RMON MIB WG                Expires August 2006                 [Page 29]


INTERNET DRAFT                 RAQMON MIB                  February 2006


                The value during a session must be greater than or
                equal to this value for an exception to be created."
           ::= { raqmonSessionExceptionEntry 4 }

       raqmonSessionExceptionLostPacketsThreshold OBJECT-TYPE
           SYNTAX Unsigned32 (0..1000)
           UNITS  "tenth of a percent"
           MAX-ACCESS read-create
           STATUS current
           DESCRIPTION
               "Threshold for lost packets in units of tenth
                of a percent.  The value during a session must
                be greater than or equal to this value for an
                exception to be created."
           ::= { raqmonSessionExceptionEntry 5 }

       raqmonSessionExceptionRowStatus OBJECT-TYPE
           SYNTAX RowStatus
           MAX-ACCESS read-create
           STATUS current
           DESCRIPTION
               "This object has a value of 'active' when
                exceptions are being monitored by the system.
                A newly-created conceptual row must have all
                the read-create objects initialized before
                becoming 'active'. A conceptual row that is in
                the 'notReady' or 'notInService' state MAY be
                removed after 5  minutes. No writeable objects
                can be changed while the row is active."
           ::= { raqmonSessionExceptionEntry 7 }


       raqmonConfig OBJECT IDENTIFIER ::= { raqmonMIBObjects 3 }

       raqmonConfigPort OBJECT-TYPE
           SYNTAX InetPortNumber
           MAX-ACCESS read-write
           STATUS current
           DESCRIPTION
               "The UDP port to listen on for RAQMON reports,
                running on other transport protocols than SNMP.
                If the RAQMON PDU transport protocol is SNMP,
                a write operation on this object has no effect, as
                the standard port 162 is always used.
                The value of this object MUST be persistent across
                agent reboots."
           ::= { raqmonConfig 1 }




RMON MIB WG                Expires August 2006                 [Page 30]


INTERNET DRAFT                 RAQMON MIB                  February 2006


          raqmonConfigPduTransport OBJECT-TYPE
            SYNTAX BITS
               {
                   other(0),
                   tcp(1),
                   snmp(2)
               }
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "The PDU transport(s) used by this collector.
                If other(0) is set, the collector supports a
                transport other than SNMP or TCP.
                If tcp(1) is set, the collector supports TCP as a
                transport protocol.
                If snmp(2) is set, the collector supports SNMP as a
                transport protocol."
           ::= { raqmonConfig 2 }


       raqmonConfigRaqmonPdus OBJECT-TYPE
           SYNTAX Counter32
           UNITS  "PDUs"
           MAX-ACCESS read-only
           STATUS current
           DESCRIPTION
               "Count of RAQMON PDUs received by the Collector."
           ::= { raqmonConfig 3 }

       raqmonConfigRDSTimeout OBJECT-TYPE
           SYNTAX Unsigned32
           MAX-ACCESS read-write
           STATUS current
           DESCRIPTION
               "The number of seconds since the reception of the
                last RAQMON PDU from a RDS after which a session
                between the respective RDS and the collector will be
                considered terminated.
                The value of this object MUST be persistent across
                agent reboots."
           ::= { raqmonConfig 4 }




       raqmonConformance OBJECT IDENTIFIER ::= { raqmonMIB 2 }





RMON MIB WG                Expires August 2006                 [Page 31]


INTERNET DRAFT                 RAQMON MIB                  February 2006


       raqmonCompliances OBJECT IDENTIFIER ::= { raqmonConformance 1 }
       raqmonGroups OBJECT IDENTIFIER ::= { raqmonConformance 2 }

       raqmonCompliance MODULE-COMPLIANCE
           STATUS  current
           DESCRIPTION
               "Describes the requirements for conformance to the
                RAQMON MIB."
           MODULE  -- this module
           MANDATORY-GROUPS { raqmonCollectorGroup,
                              raqmonCollectorNotificationsGroup
                            }

           OBJECT raqmonParticipantAddrType
           SYNTAX  InetAddressType { ipv4(1), ipv6(2) }
           DESCRIPTION
               "Only IPv4 and IPv6 addresses need to be supported"

           OBJECT raqmonParticipantAddr
           SYNTAX  InetAddress (SIZE(4|16))
           DESCRIPTION
               "Only IPv4 and IPv6 addresses need to be supported"

           OBJECT raqmonParticipantPeerAddrType
           SYNTAX  InetAddressType { ipv4(1), ipv6(2) }
           DESCRIPTION
               "Only IPv4 and IPv6 addresses need to be supported"

           OBJECT raqmonParticipantPeerAddr
           SYNTAX  InetAddress (SIZE(4|16))
           DESCRIPTION
               "Only IPv4 and IPv6 addresses need to be supported"

              ::= { raqmonCompliances 1 }


       raqmonCollectorGroup OBJECT-GROUP
           OBJECTS {
               raqmonParticipantReportCaps,
               raqmonParticipantAddrType,
               raqmonParticipantAddr,
               raqmonParticipantSendPort,
               raqmonParticipantRecvPort,
               raqmonParticipantSetupDelay,
               raqmonParticipantName,
               raqmonParticipantAppName,
               raqmonParticipantQosCount,
               raqmonParticipantEndDate,



RMON MIB WG                Expires August 2006                 [Page 32]


INTERNET DRAFT                 RAQMON MIB                  February 2006


               raqmonParticipantDestPayloadType,
               raqmonParticipantSrcPayloadType,
               raqmonParticipantActive,
               raqmonParticipantPeer,
               raqmonParticipantPeerAddrType,
               raqmonParticipantPeerAddr,
               raqmonParticipantSrcL2Priority,
               raqmonParticipantDestL2Priority,
               raqmonParticipantSrcDSCP,
               raqmonParticipantDestDSCP,
               raqmonParticipantCpuMean,
               raqmonParticipantCpuMin,
               raqmonParticipantCpuMax,
               raqmonParticipantMemoryMean,
               raqmonParticipantMemoryMin,
               raqmonParticipantMemoryMax,
               raqmonParticipantNetRTTMean,
               raqmonParticipantNetRTTMin,
               raqmonParticipantNetRTTMax,
               raqmonParticipantIAJitterMean,
               raqmonParticipantIAJitterMin,
               raqmonParticipantIAJitterMax,
               raqmonParticipantIPDVMean,
               raqmonParticipantIPDVMin,
               raqmonParticipantIPDVMax,
               raqmonParticipantNetOwdMean,
               raqmonParticipantNetOwdMin,
               raqmonParticipantNetOwdMax,
               raqmonParticipantAppDelayMean,
               raqmonParticipantAppDelayMin,
               raqmonParticipantAppDelayMax,
               raqmonParticipantPacketsRcvd,
               raqmonParticipantPacketsSent,
               raqmonParticipantOctetsRcvd,
               raqmonParticipantOctetsSent,
               raqmonParticipantLostPackets,
               raqmonParticipantLostPacketsFrct,
               raqmonParticipantDiscards,
               raqmonParticipantDiscardsFrct,
               raqmonQoSEnd2EndNetDelay,
               raqmonQoSInterArrivalJitter,
               raqmonQosRcvdPackets,
               raqmonQosRcvdOctets,
               raqmonQosSentPackets,
               raqmonQosSentOctets,
               raqmonQosLostPackets,
               raqmonQosSessionStatus,
               raqmonParticipantAddrEndDate,



RMON MIB WG                Expires August 2006                 [Page 33]


INTERNET DRAFT                 RAQMON MIB                  February 2006


               raqmonConfigPort,
               raqmonSessionExceptionIAJitterThreshold,
               raqmonSessionExceptionNetRTTThreshold,
               raqmonSessionExceptionLostPacketsThreshold,
               raqmonSessionExceptionRowStatus,
               raqmonConfigPduTransport,
               raqmonConfigRaqmonPdus,
               raqmonConfigRDSTimeout}
           STATUS current
           DESCRIPTION
               "Objects used in RAQMON by a Collector"


           ::= { raqmonGroups 1 }

       raqmonCollectorNotificationsGroup NOTIFICATION-GROUP
           NOTIFICATIONS { raqmonSessionAlarm }
           STATUS current
           DESCRIPTION
               "Notifications emitted by a RAQMON collector."
           ::= { raqmonGroups 2 }

   END



6.  Security Considerations

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write.  Such objects may be
   considered sensitive or vulnerable in some network environments.
   The support for SET operations in a non-secure environment without
   proper protection can have a negative effect on network operations.

   Setting the value of the object raqmonRDSTimeout to a too low value
   would result in RDS sessions being terminated sooner than necessary,
   while setting at a too high value may result in terminated sessions
   continuing to be managed, with unnecessary memory allocations.

   Setting the following object to incorrect values can result in
   collectors either flooding the management applications with
   unnecessary notifications, or not sending notifications when the
   QoS in the network may be degraded.

      raqmonSessionExceptionIAJitterThreshold
      raqmonSessionExceptionRTTThreshold
      raqmonSessionExceptionLostPacketsThreshold




RMON MIB WG                Expires August 2006                 [Page 34]


INTERNET DRAFT                 RAQMON MIB                  February 2006


   Setting the raqmonConfigPort object to incorrect values can result in
   the collector not being able to receive RAQMON PDUs from the data
   sources.

   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments.  These are:

      raqmonParticipantTable
      raqmonQoSTable
      raqmonParticpantAddrTable

   Unauthorized exposure of these objects may lead to disclosure of the
   addresses of the participants in applications, or information about
   the traffic patents of the applications, which may be considered
   sensitive in certain environments.

   It is thus important to control even GET and/or NOTIFY access to
   these objects and possibly to even encrypt their values when sending
   them over the network via SNMP.

   The structure of the RAQMON tables limits what can be usefully done
   for access control configuration using VACM. For example, it would
   not be possible with these structures to provide a group, with access
   to performance data to a specific group of devices, since the index
   values for raqmonParticpantEntry cannot be known in advance.
   Likewise, raqmonSessionExceptionEntries apply to all entries in the
   raqmonQoSTable.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   in this MIB module.

   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.




RMON MIB WG                Expires August 2006                 [Page 35]


INTERNET DRAFT                 RAQMON MIB                  February 2006


7. IANA Considerations

   No requirements from IANA are defined in this document. The root OID
   of the MIB module defined in this document belongs to the RMON
   subtree, as reserved in [RFC3737].


8.  Acknowledgements

   Richard Smith created the first proprietary version of this MIB.

   The authors would also like to thank to all the participants in the
   Remote Monitoring MIB Working Group, and especially to Andy Bierman,
   Steven Waldbusser, Alan Clark, Itai Zilbershtein, and Robert Cole for
   interesting discussions, ideas, comments and direct contributions
   to this work.

   The authors would also like to thank Randy Presuhn for the precious
   technical comments, as well as for the laborious activity of
   reviewing the syntax and spelling of the document.

   The authors would like to thank Bert Wijnen for the review of the
   final versions of the document, as well as for the guidance provided
   during the whole period of editing.

Normative References

   [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
               Rose, M., and S. Waldbusser, "Structure of Management
               Information Version 2 (SMIv2)", STD 58, RFC 2578, April
               1999.

   [RFC2579]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
               Rose, M., and S. Waldbusser, "Textual Conventions for
               SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
               Rose, M., and S. Waldbusser, "Conformance Statements for
               SMIv2", STD 58, RFC 2580, April 1999.

   [RFC2819]   Waldbusser, S., "Remote Network Monitoring Management
               Information Base", STD 59, RFC 2819, May 2000.

   [RFC3411]   Harrington, D., Preshun, R. and B. Wijnen, "An
               Architecture for Describing Simple Network Management



RMON MIB WG                Expires August 2006                 [Page 36]


INTERNET DRAFT                 RAQMON MIB                  February 2006


               Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
               December 2002.

   [RFC4001]   Daniele, M., Haberman, B., Routhier, S. and
               J. Schoenwalder, "Textual Conventions for Internet
               Network Addresses", RFC 4001, February 2005.

   [RAQMON-FRAMEWORK] A. Siddiqui, D.Romascanu, and Golovinsky, E.,
               "Framework for Real-time Application Quality of
               Service Monitoring (RAQMON)", Internet-Draft,
               draft-ietf-rmonmib-raqmon-framework-15.txt,
               February 2006.

Informative References

   [RFC3410]   Case, J., Mundy, R., Partain, D., and B. Stewart,
               "Introduction and Applicability Statements for Internet-
               Standard Management Framework", RFC 3410, December 2002.

   [RAQMON-PDU] Siddiqui, A., Romascanu, D., Golovinsky, E., Ramhman,
                M.,and Y. Kim, "Transport Mappings for Real-time
                Application Quality of Service Monitoring (RAQMON)
                Protocol Data Unit (PDU)",Internet-Draft,
                draft-ietf-raqmon-pdu-13.txt,
    February 2006.

   [RFC3737]   Wijnen B., and A.Bierman
               "IANA Guidelines for the Registry of Remote Monitoring
               (RMON) MIB modules", RFC 3737, April 2004.


Authors' Addresses

   Anwar A. Siddiqui
   Avaya Labs
   307 Middletown Lincroft Road
   Lincroft, New Jersey 07738
   USA
   Tel: +1 732 852-3200
   Fax: +1 732 817-5922
   E-mail: anwars@avaya.com

   Dan Romascanu
   Avaya
   Atidim Technology Park, Bldg. #3
   Tel Aviv, 61131
   Israel
   Tel: +972 3-645-8414



RMON MIB WG                Expires August 2006                 [Page 37]


INTERNET DRAFT                 RAQMON MIB                  February 2006


   Email: dromasca@avaya.com

   Eugene Golovinsky
   BMC Software
   2101 CityWest Blvd.
   Houston, Texas 77042
   USA
   Tel: +1 713 918-1816
   Email: eugene_golovinsky@bmc.com

Full Copyright Statement

   Copyright (C) The Internet Society (2006).  This document is subject
   to the rights, licenses and restrictions contained in BCP 78, and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


IPR Disclosure Acknowledgement

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights. Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.



RMON MIB WG                Expires August 2006                 [Page 38]


INTERNET DRAFT                 RAQMON MIB                  February 2006





















































RMON MIB WG                Expires August 2006                 [Page 39]