Routing over Large Clouds Working Group Dave Katz
INTERNET-DRAFT (cisco Systems)
<draft-ietf-rolc-nhrp-07.txt> David Piscitello
(Core Competence, Inc.)
Bruce Cole
(cisco Systems)
James V. Luciani
(Ascom Nexion)
Expires June 1996
NBMA Next Hop Resolution Protocol (NHRP)
Status of this Memo
This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as ``work in progress.''
To learn the current status of any Internet-Draft, please check the
``1id-abstracts.txt'' listing contained in the Internet-Drafts Shadow
Directories on ds.internic.net (US East Coast), nic.nordu.net
(Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific
Rim).
Abstract
This document describes the NBMA Next Hop Resolution Protocol (NHRP).
NHRP can be used by a source station (host or router) connected to a
Non-Broadcast, Multi-Access (NBMA) subnetwork to determine the
internetworking layer address and NBMA subnetwork addresses of the
"NBMA next hop" towards a destination station. If the destination is
connected to the NBMA subnetwork, then the NBMA next hop is the
destination station itself. Otherwise, the NBMA next hop is the
egress router from the NBMA subnetwork that is "nearest" to the
destination station. NHRP is intended for use in a multiprotocol
internetworking layer environment over NBMA subnetworks.
This document is intended to be a functional superset of the NBMA
Address Resolution Protocol (NARP) documented in [1].
Katz, Piscitello, Cole, Luciani [Page 1]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Operation of NHRP as a means of establishing a transit path across an
NBMA subnetwork between two routers will be addressed in a separate
document.
1. Introduction
The NBMA Next Hop Resolution Protocol (NHRP) allows a source station
(a host or router), wishing to communicate over a Non-Broadcast,
Multi-Access (NBMA) subnetwork, to determine the internetworking
layer addresses and NBMA addresses of suitable "NBMA next hops"
toward a destination station. A subnetwork can be non-broadcast
either because it technically doesn't support broadcasting (e.g., an
X.25 subnetwork) or because broadcasting is not feasible for one
reason or another (e.g., an SMDS multicast group or an extended
Ethernet would be too large). If the destination is connected to the
NBMA subnetwork, then the NBMA next hop is the destination station
itself. Otherwise, the NBMA next hop is the egress router from the
NBMA subnetwork that is "nearest" to the destination station.
An NBMA subnetwork may, in general, consist of multiple Local Address
Groups (LAGs). In the case of IP, a logically independent IP subnet
(LIS) is an example of a LAG. LISs, as defined in [3] and [4], have
the following properties:
1) All members of a LIS have the same IP network/subnet number
and address mask.
2) All members within a LIS are directly connected to the same
NBMA subnetwork.
3) All members outside of the LIS are accessed via a router.
Address resolution as described in [3] and [4] only resolves the next
hop address if the destination station is a member of the same LIS as
the source station; otherwise, the source station must forward
packets to a router that is a member of multiple LIS's. In multi-LIS
configurations, hop-by-hop address resolution may not be sufficient
to resolve the "NBMA next hop" toward the destination station, and IP
packets may traverse the NBMA subnetwork more than once.
NHRP describes a next hop resolution method that relaxes the
forwarding restrictions of the LIS model. With NHRP when the
internetwork layer address is of type IP, once the NBMA next hop has
been resolved, the source may either start sending IP packets to the
destination (in a connectionless NBMA subnetwork such as SMDS) or may
first establish a connection to the destination with the desired
bandwidth and QOS characteristics (in a connection-oriented NBMA
Katz, Piscitello, Cole, Luciani [Page 2]
INTERNET-DRAFT NBMA NHRP Expires June 1996
subnetwork such as ATM).
NHRP in its most basic form provides a simple internetworking layer
to NBMA subnetwork layer address binding service. This may be
sufficient for hosts which are directly connected to an NBMA
subnetwork, allowing for straightforward implementations in NBMA
stations. NHRP also has the capability of determining the egress
point from an NBMA subnetwork when the destination is not directly
connected to the NBMA subnetwork and the identity of the egress
router is not learned by other methods (such as routing protocols).
Optional extensions to NHRP provide additional robustness and
diagnosability.
Address resolution techniques such as those described in [3] and [4]
may be in use when NHRP is deployed. ARP servers and services over
NBMA subnetworks may be required to support hosts that are not
capable of dealing with any model for communication other than the
LIS model, and deployed hosts may not implement NHRP but may continue
to support ARP variants such as those described in [3] and [4]. NHRP
is intended to reduce or eliminate the extra router hops required by
the LIS model, and can be deployed in a non-interfering manner
alongside existing ARP services.
The operation of NHRP to establish transit paths across NBMA
subnetworks between two routers requires additional mechanisms to
avoid stable routing loops, and will be described in a separate
document.
2. Overview
2.1 Terminology
The term "network" is highly overloaded, and is especially confusing
in the context of NHRP. We use the following terms:
Internetwork layer--the media-independent layer (IP in the case of
TCP/IP networks).
Subnetwork layer--the media-dependent layer underlying the
internetwork layer, including the NBMA technology (ATM, X.25, SMDS,
etc.)
2.2 Protocol Overview
In this section, we briefly describe how a source S (which
potentially can be either a router or a host) uses NHRP to determine
Katz, Piscitello, Cole, Luciani [Page 3]
INTERNET-DRAFT NBMA NHRP Expires June 1996
the "NBMA next hop" to destination D.
For administrative and policy reasons, a physical NBMA subnetwork may
be partitioned into several, disjoint "Logical NBMA subnetworks". A
Logical NBMA subnetwork is defined as a collection of hosts and
routers that share unfiltered subnetwork connectivity over an NBMA
subnetwork. "Unfiltered subnetwork connectivity" refers to the
absence of closed user groups, address screening or similar features
that may be used to prevent direct communication between stations
connected to the same NBMA subnetwork. (Hereafter, unless otherwise
specified, we use the term "NBMA subnetwork" to mean *logical* NBMA
subnetwork.)
Placed within the NBMA subnetwork are one or more entities that
implement the NHRP protocol. Such stations which are capable of
answering Next Hop Resolution Requests are known as "Next Hop
Servers" (NHSs). Each NHS serves a set of destination hosts, which
may or may not be directly connected to the NBMA subnetwork. NHSs
cooperatively resolve the NBMA next hop within their logical NBMA
subnetwork. In addition to NHRP, NHSs may participate in protocols
used to disseminate routing information across (and beyond the
boundaries of) the NBMA subnetwork, and may support "classical" ARP
service as well.
An NHS maintains a "next-hop resolution" cache, which is a table of
address mappings (internetwork layer address to NBMA subnetwork layer
address). This table can be constructed from information gleaned from
NHRP Register packets (see Section 5.2.3 and 5.2.4), extracted from
Next Hop Resolution Requests/Replies that traverse the NHS as they
are forwarded, or through mechanisms outside the scope of this
document (examples of such mechanisms include ARP [2, 3, 4] and pre-
configured tables). Section 6.2 further describes cache management
issues.
A host or router that is not an NHRP server must be configured with
the identity of the NHS which serves it (see Configuration, Section
4).
[Note: for NBMA subnetworks that offer group or multicast addressing
features, it may be desirable to configure stations with a group
identity for NHSs, i.e., addressing information that would solicit a
response from "all NHSs". The means whereby a group of NHSs divide
responsibilities for next hop resolution are not described here.]
Whether or not a particular station within the NBMA subnetwork which
is making use of the NHRP protocol needs to be able to act as an NHS
is a local matter. For a station to avoid providing NHS
functionality, there must be one or more NHSs within the NBMA
Katz, Piscitello, Cole, Luciani [Page 4]
INTERNET-DRAFT NBMA NHRP Expires June 1996
subnetwork which are providing authoritative NBMA information on its
behalf. If NHRP is to be able to resolve the NBMA address for
stations that lack NHS functionality, these serving NHSs must exist
along all routed paths between Next Hop Resolution Requesters and the
station which cannot answer Next Hop Resolution Requests.
The protocol proceeds as follows. An event occurs triggering station
S to want to resolve the NBMA address of a path to D. This is most
likely to be when a data packet addressed to station D is to be
emitted from station S (either because station S is a host, or
station S is a transit router), but the address resolution could also
be triggered by other means (a routing protocol update packet, for
example). Station S first determines the next hop to station D
through normal routing processes (for a host, the next hop may simply
be the default router; for routers, this is the "next hop" to the
destination internetwork layer address). If the next hop is
reachable through its NBMA interface, S constructs an Next Hop
Resolution Request packet (see Section 5.2.1) containing station D's
internetwork layer address as the (target) destination address, S's
own internetwork layer address as the source address (Next Hop
Resolution Request initiator), and station S's NBMA addressing
information. Station S may also indicate that it prefers an
authoritative Next Hop Resolution Reply (i.e., station S only wishes
to receive a Next Hop Resolution Reply from the NHS-speaker that
maintains the NBMA-to-internetwork layer address mapping for this
destination). Station S emits the Next Hop Resolution Request packet
towards the destination, using the NBMA address of the next routed
hop.
If the Next Hop Resolution Request is triggered by a data packet,
station S may choose to dispose of the data packet while awaiting a
Next Hop Resolution Reply in one of the following ways:
(a) Drop the packet
(b) Retain the packet until the Next Hop Resolution Reply arrives
and a more optimal path is available
(c) Forward the packet along the routed path toward D
The choice of which of the above to perform is a local policy matter,
though option (c) is the recommended default, since it may allow data
to flow to the destination while the NBMA address is being resolved.
Note that an Next Hop Resolution Request for a given destination MUST
NOT be triggered on every packet, though periodically retrying a Next
Hop Resolution Request is permitted.
When the NHS receives an Next Hop Resolution Request, a check is made
to see if it "serves" station D, i.e., the NHS checks to see if there
is a "next hop" entry for D in its next-hop resolution cache. If the
Katz, Piscitello, Cole, Luciani [Page 5]
INTERNET-DRAFT NBMA NHRP Expires June 1996
NHS does not serve D, the NHS forwards the Next Hop Resolution
Request to another NHS. (Mechanisms for determining how to forward
the Next Hop Resolution Request are discussed in Section 3,
Deployment.) Note that NHSs must be next hops to one another in order
for forwarding of NHRP packets to be possible.
If this NHS serves D, the NHS resolves station D's NBMA address, and
generates a positive Next Hop Resolution Reply on D's behalf. (Next
Hop Resolution Replies in this scenario are always marked as
"authoritative".) The Next Hop Resolution Reply packet contains the
next hop internetwork layer address and the NBMA address for station
D and is sent back to S. (Note that if station D is not on the NBMA
subnetwork, the next hop internetwork layer address will be that of
the egress router through which packets for station D are forwarded.)
An NHS receiving a Next Hop Resolution Reply may cache the NBMA next
hop information contained therein. To a subsequent Next Hop
Resolution Request, this NHS may respond with the cached, non-
authoritative, NBMA next hop information or with cached negative
information, if the NHS is allowed to do so, see section 6.2. Non-
authoritative Next Hop Resolution Replies are distinguished from
authoritative Next Hop Resolution Replies so that if a communication
attempt based on non-authoritative information fails, a source
station can choose to send an authoritative Next Hop Resolution
Request. NHSs MUST NOT respond to authoritative Next Hop Resolution
Requests with cached information.
[Note: An Next Hop Resolution Reply can be returned directly to the
Next Hop Resolution Request initiator, i.e., without traversing the
list of NHSs that forwarded the Next Hop Resolution Request, if all
of the following criteria are satisfied:
(a) Direct communication is available via datagram transfer
(e.g., SMDS) or the NHS has an existing virtual circuit
connection to the Next Hop Resolution Request initiator or is
permitted to open one.
(b) The Next Hop Resolution Request initiator has not included the
NHRP Reverse NHS record Extension (see Section 5.3.5).
(c) The authentication policy in force permits direct
communication between the NHS and the Next Hop Resolution
Request initiator.
The purpose of allowing an NHS to send a Next Hop Resolution Reply
directly is to reduce response time. A consequence of allowing a
direct Next Hop Resolution Reply is that NHSs that would under
normal circumstances be traversed by the Next Hop Resolution Reply
would not cache next hop information contained therein.]
Katz, Piscitello, Cole, Luciani [Page 6]
INTERNET-DRAFT NBMA NHRP Expires June 1996
The process of forwarding the Next Hop Resolution Request is repeated
until the Next Hop Resolution Request is satisfied, or an error
occurs (e.g., no NHS in the NBMA subnetwork can resolve the Next Hop
Resolution Request.) If the determination is made that station D's
next hop cannot be resolved, a negative Next Hop Resolution Reply
(NAK) is returned. This occurs when (a) no next-hop resolution
information is available for station D from any NHS, or (b) an NHS is
unable to forward the Next Hop Resolution Request (e.g., connectivity
is lost).
NHRP Registration Requests, NHRP Registration Replies, NHRP Purge
Requests, NHRP Purge Replies, and NHRP Error Indications follow the
routed path from sender to receiver in the same fashion that Next Hop
Resolution Requests and Next Hop Resolution Replies do. That is,
"requests" and "indications" follow the routed path from Source
Protocol Address (which is the address of the station initiating the
communication) to the Destination Protocol Address. "Replies", on
the other hand, follow the routed path from the Destination Protocol
Address back to the Source Protocol Address with the exceptions
mentioned above where a direct VC may be created.
Next Hop Resolution Requests and Next Hop Resolution Replies MUST NOT
cross the borders of a logical NBMA subnetwork (an explicit NBMA
subnetwork identifier may be included as an extension in the Next Hop
Resolution Request, see section 5.3.2). Thus, the internetwork layer
traffic out of and into a logical NBMA subnetwork always traverses an
internetwork layer router at its border. Internetwork layer
filtering can then be implemented at these border routers.
NHRP optionally provides a mechanism to send a Next Hop Resolution
Reply which contains aggregated NBMA next hop information. Suppose
that router X is the NBMA next hop from station S to station D.
Suppose further that X is an egress router for all stations sharing
an internetwork layer address prefix with station D. When an Next
Hop Resolution Reply is generated in response to a Next Hop
Resolution Request, the responder may augment the internetwork layer
address of station D with a prefix length (see Section 5.3.1). A
subsequent (non-authoritative) Next Hop Resolution Request for some
destination that shares an internetwork layer address prefix (for the
number of bits specified in the prefix length) with D may be
satisfied with this cached information. See section 6.2 regarding
caching issues.
To dynamically detect subnetwork-layer filtering in NBMA subnetworks
(e.g., X.25 closed user group facility, or SMDS address screens), as
well as to provide loop detection and diagnostic capabilities, a
"Route Record" may be included in NHRP packets (see Sections 5.3.4
and 5.3.5). The Route Record extensions contain the internetwork
Katz, Piscitello, Cole, Luciani [Page 7]
INTERNET-DRAFT NBMA NHRP Expires June 1996
(and subnetwork layer) addresses of all intermediate NHSs between
source and destination (in the forward direction) and between
destination and source (in the reverse direction). When a source
station is unable to communicate with the responder (e.g., an attempt
to open an SVC fails), it may attempt to do so successively with
other subnetwork layer addresses in the Route Record until it
succeeds (if authentication policy permits such action). This
approach can find a suitable egress point in the presence of
subnetwork-layer filtering (which may be source/destination
sensitive, for instance, without necessarily creating separate
logical NBMA subnetworks) or subnetwork-layer congestion (especially
in connection-oriented media).
3. Deployment
Next Hop Resolution Requests traverse one or more hops within an NBMA
subnetwork before reaching the station that is expected to generate a
response. Each station, including the source station, chooses a
neighboring NHS to which it will forward the Next Hop Resolution
Request. The NHS selection procedure typically involves performing a
routing decision based upon the network layer destination address of
the Next Hop Resolution Request. Ignoring error situations, the Next
Hop Resolution Request eventually arrives at a station that is to
generate an Next Hop Resolution Reply. This responding station
either serves the destination, or is the destination itself if both
NHRP client and server functionality are co-resident in the same
station. The responding station generates a Next Hop Resolution
Reply using the source address from within the NHRP packet to
determine where the Next Hop Resolution Reply should be sent.
The Next Hop Resolution Request packet is carried at the NBMA layer,
with a destination NBMA address set to that of the locally determined
NHS. If the addressed NHS does not serve the destination address
specified in the Next Hop Resolution Request, the Next Hop Resolution
Request packet is routed at the network layer based upon the Next Hop
Resolution Requester's destination address, and forwarded to the
neighboring NHS determined by the routing decision. Alternately, the
NHS may use static configuration information in order to determine to
which neighboring NHSs to forward the Next Hop Resolution Request
packet. Each NHS/router examines the Next Hop Resolution Request
packet on its way toward the destination, optionally modifying it on
the way (such as updating the Forward Record extension), and
continues to forward it until it reaches the NHS that serves the
destination network layer address.
In order to forward NHRP packets to a neighboring NHS, NHRP clients
must nominally be configured with the NBMA address of at least one
Katz, Piscitello, Cole, Luciani [Page 8]
INTERNET-DRAFT NBMA NHRP Expires June 1996
NHS. In practice, a client's default router should also be its NHS.
A client may be able to derive the NBMA address of its NHS from the
configuration that was already required for the client to be able to
communicate with its next hop router.
Forwarding of NHRP packets within an NBMA subnetwork requires a
contiguous deployment of NHRP capable stations. During migration to
NHRP, it cannot be expected that all stations within the NBMA
subnetwork are NHRP capable. NHRP traffic which would otherwise need
to be forwarded through such stations can be expected to be dropped
due to the NHRP packet being unrecognized. In this case, NHRP will
be unable to establish any transit paths whose discovery requires the
traversal of the non-NHRP speaking stations. If the client has tried
and failed to acquire a cut through path the the client should use
the network layer routed path as a default.
The path taken by Next Hop Resolution Requests will normally be the
same as the path taken by data packets which are routed at the
network layer to the desired destination. (The paths may be
different in situations where NHSs have been statically configured to
forward traffic by other means. For example, an Next Hop Resolution
Request may be forwarded to a group multicast address.)
NHSs should acquire knowledge about destinations other NHSs serve as
a direct consequence of participating in intra-domain and inter-
domain routing protocol exchange. In this case, the NHS serving a
particular destination must lie along the routed path to that
destination. In practice, this means that all egress routers must
double as NHSs serving the destinations beyond them, and that hosts
on the NBMA subnetwork are served by routers that double as NHSs.
NHSs (and end stations) may alternately be statically configured with
the NBMA addresses of their neighbors, the identities of the
destinations that each of them serves, and optionally a logical NBMA
subnetwork identifier. Such static configurations may be necessary
in cases where NHSs do not contain network layer routing protocol
implementations.
If the NBMA subnetwork offers a link layer group addressing or
multicast feature, the client (station) may be configured with a
group address assigned to the group of next-hop servers. The client
might then submit Next Hop Resolution Requests to the group address,
eliciting a response from one or more NHSs, depending on the response
strategy selected. Note that the constraints described in Section 2
regarding directly sending Next Hop Resolution Reply may apply.
NHSs may also be deployed with the group or multicast address of
their peers, and an NHS might use this as a means of forwarding Next
Katz, Piscitello, Cole, Luciani [Page 9]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Hop Resolution Requests it cannot satisfy to its peers. This might
elicit a response (to the NHS) from one or more NHSs, depending on
the response strategy. The NHS would then forward the Next Hop
Resolution Reply to the Next Hop Resolution Request originator. The
purpose of using group addressing or a similar multicast mechanism in
this scenario would be to eliminate the need to preconfigure each NHS
in a logical NBMA subnetwork with both the individual identities of
other NHSs as well as the destinations they serve. It reduces the
number of NHSs that might be traversed to process an Next Hop
Resolution Request (in those configurations where NHSs either respond
or forward via the multicast, only two NHSs would be traversed), and
allows the NHS that serves the Next Hop Resolution Request originator
to cache next hop information associated with the Next Hop Resolution
Reply (again, within the constraints described in Section 2).
4. Configuration
Stations
To participate in NHRP, a station connected to an NBMA subnetwork
should be configured with the NBMA address(es) of its NHS(s)
(alternatively, it should be configured with a means of acquiring
them, i.e., the group address that members of a NHS group use for
the purpose of address or next-hop resolution.) The NHS(s) will
likely also represent the station's default or peer routers, so
their NBMA addresses may be obtained from the station's existing
configuration. If the station is attached to several subnetworks
(including logical NBMA subnetworks), the station should also be
configured to receive routing information from its NHS(s) and peer
routers so that it can determine which internetwork layer networks
are reachable through which subnetworks.
Next Hop Servers
An NHS is configured with knowledge of its own internetwork layer
and NBMA addresses, a set of internetwork layer address prefixes
that correspond to the internetwork layer addresses of the stations
it serves, and a logical NBMA subnetwork identifier (see Section
5.3.2). If a served station is attached to several subnetworks,
the NHS may also need to be configured to advertise routing
information to such stations.
If an NHS acts as an egress router for stations connected to other
subnetworks than the NBMA subnetwork, the NHS must, in addition to
the above, be configured to exchange routing information between
the NBMA subnetwork and these other subnetworks.
Katz, Piscitello, Cole, Luciani [Page 10]
INTERNET-DRAFT NBMA NHRP Expires June 1996
In all cases, routing information is exchanged using conventional
intra-domain and/or inter-domain routing protocols.
The NBMA addresses of the stations served by the NHS may be learned
via NHRP Register packets or manual configuration.
5. NHRP Packet Formats
This section describes the format of NHRP packets.
An NHRP packet consists of a Fixed Part, a Mandatory Part, and an
Extensions Part. The Fixed Part is common to all NHRP packet types.
The Mandatory Part MUST be present, but varies depending on packet
type. The Extensions Part also varies depending on packet type, and
need not be present.
The length of the Fixed Part is fixed at 20 octets. The length of
the Mandatory Part is determined by the contents of the extensions
offset field (ar$extoff). If ar$extoff=0x0 then the mandatory part
length is equal to total packet length (ar$pktsz) minus 20 otherwise
the mandatory part length is equal to ar$extoff minus 20. The length
of the Extensions Part is implied by ar$pktsz minus ar$extoff minus
20. NHSs may increase the size of an NHRP packet as a result of
extension processing, but not beyond the offered maximum SDU size of
the NBMA network.
NHRP packets are encapsulated using the native formats used on the
particular NBMA network over which NHRP is carried. For example,
SMDS networks always use LLC/SNAP encapsulation at the NBMA layer,
and an NHRP packet is preceded by the following LLC/SNAP
encapsulation:
[0xAA-AA-03] [0x00-00-5E] [0x00-03]
The first three octets are LLC, indicating that SNAP follows. The
SNAP OUI portion is the IANA's OUI, and the SNAP PID portion
identifies NHRP (see [4]).
ATM uses either LLC/SNAP encapsulation of each packet (including
NHRP), or uses no encapsulation on VCs dedicated to a single protocol
(see [7]). Frame Relay and X.25 both use NLPID/SNAP encapsulation or
identification of NHRP, using a NLPID of 0x0080 and the same SNAP
contents as above (see [8], [9]).
Fields marked "unused" MUST be set to zero on transmission, and
ignored on receipt.
Most packet types (ar$op.type) have both internetwork layer
protocol-independent fields and protocol-specific fields. The
Katz, Piscitello, Cole, Luciani [Page 11]
INTERNET-DRAFT NBMA NHRP Expires June 1996
protocol-independent fields always come first in the packet, and the
protocol type/snap fields (ar$pro.type/snap) qualify the format of
the protocol-specific fields.
5.1 NHRP Fixed Header
The Fixed Part of the NHRP packet contains those elements of the NHRP
packet which are always present and do not vary in size with the type
of packet.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$afn | ar$pro.type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$pro.snap |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$pro.snap | ar$hopcnt | ar$pktsz |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$chksum | ar$extoff |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$op.version | ar$op.type | ar$shtl | ar$sstl |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ar$afn
Defines the type of "link layer" addresses being carried. This
number is taken from the 'address family number' list specified in
[6]. This field has implications to the coding of ar$shtl and
ar$sstl as described below.
ar$pro.type
field is a 16 bit unsigned integer representing the following
number space:
0x0000 to 0x00FF Protocols defined by the equivalent NLPIDs.
0x0100 to 0x03FF Reserved for future use by the IETF.
0x0400 to 0x04FF Allocated for use by the ATM Forum.
0x0500 to 0x05FF Experimental/Local use.
0x0600 to 0xFFFF Protocols defined by the equivalent Ethertypes.
(based on the observations that valid Ethertypes are never smaller
than 0x600, and NLPIDs never larger than 0xFF.)
ar$pro.snap
When ar$pro.type has a value of 0x0080, a SNAP encoded extension is
Katz, Piscitello, Cole, Luciani [Page 12]
INTERNET-DRAFT NBMA NHRP Expires June 1996
being used to encode the protocol type. This snap extension is
placed in the ar$pro.snap field. This is termed the 'long form'
protocol ID. If ar$pro != 0x0080 then the ar$pro.snap field MUST be
zero on transmit and ignored on receive. The ar$pro.type field
itself identifies the protocol being referred to. This is termed
the 'short form' protocol ID.
In all cases, where a protocol has an assigned number in the
ar$pro.type space (excluding 0x0080) the short form MUST be used
when transmitting NHRP messages. Additionally, where a protocol has
valid short and long forms of identification, receivers MAY choose
to recognize the long form.
ar$hopcnt
The Hop count indicates the maximum number of NHSs that an NHRP
packet is allowed to traverse before being discarded.
ar$pktsz
The total length of the NHRP packet, in octets (excluding link
layer encapsulation).
ar$chksum
The standard IP checksum over the entire NHRP packet (starting with
the fixed header). If only the hop count field is changed, the
checksum is adjusted without full recomputation. The checksum is
completely recomputed when other header fields are changed.
ar$extoff
This field identifies the existence and location NHRP extensions.
If this field is 0 then no extensions exist otherwise this field
represents the offset from the beginning of the NHRP packet (i.e.,
starting from the ar$afn field) of the first extension.
ar$op.version
This field is set to 0x0001 for NHRP version 1.
ar$op.type
This is the NHRP packet type: NHRP Next Hop Resolution Request(1),
NHRP Next Hop Resolution Reply(2), NHRP Registration Request(3),
NHRP Registration Reply(4), NHRP Purge Request(5), NHRP Purge
Reply(6), or NHRP Error Indication(7).
ar$shtl
Type & length of source NBMA address interpreted in the context of
the 'address family number'[6] indicated by ar$afn (e.g.,
ar$afn=0x0003 for NSAP, ar$afn=8 for E.164). When ar$afn=0x000F
(E.164 address plus NSAP subaddress) then both ar$shtl and ar$sstl
must be coded appropriately (see below).
Katz, Piscitello, Cole, Luciani [Page 13]
INTERNET-DRAFT NBMA NHRP Expires June 1996
ar$sstl
Type & length of source NBMA subaddress interpreted in the context
of the 'address family number'[6] indicated by ar$afn (e.g.,
ar$afn=0x000F for NSAP). When an NBMA technology has no concept of
a subaddress, the subaddress length is always coded ar$sstl = 0 and
no storage is allocated for the subaddress in the appropriate
mandatory part.
ar$shtl, ar$sstl, subnetwork layer addresses, and subnetwork layer
subaddresses fields are coded as follows:
7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+
|0|x| length |
+-+-+-+-+-+-+-+-+
The most significant bit is reserved and MUST be set to zero. The
second most significant bit (x) is a flag indicating whether the
address being referred to is in:
- NSAP format (x = 0).
- Native E.164 format (x = 1).
For NBMA technologies that use neither NSAP nor E.164 format
addresses, x = 0 SHALL be used to indicate the native form for the
particular NBMA technology.
In the case where the NBMA is ATM, if a subaddress is to be included
then ar$afn MUST be set to 0x000F which means that if a subaddress
exists then it is of type NSAP.
The bottom 6 bits is an unsigned integer value indicating the length
of the associated NBMA address in octets. If this value is zero the
flag x is ignored.
5.2 Mandatory Part
The Mandatory Part of the NHRP packet contains the operation specific
information (e.g., Next Hop Resolution Request/Reply, etc.) and
variable length data which is pertinent to the packet type.
5.2.1 NHRP Next Hop Resolution Request
The NHRP Next Hop Resolution Request packet has a Type code of 1. The
Mandatory Part has the following format:
Katz, Piscitello, Cole, Luciani [Page 14]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len |Q|A|P|B| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Maximum Transmission Unit | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
NHRP Next Hop Resolution Request/Reply Flags
Q
Set if the station sending the Next Hop Resolution Request is a
router; clear if the it is a host.
A
A response to a Next Hop Resolution Request may contain cached
information. If an authoritative answer is desired, then this bit
("Authoritative") should be set. If non-authoritative (cached)
information is acceptable, this bit should be clear.
P
Unused (clear on transmit)
B
Unused (clear on transmit)
Request ID
A value which, when coupled with the address of the source,
Katz, Piscitello, Cole, Luciani [Page 15]
INTERNET-DRAFT NBMA NHRP Expires June 1996
provides a unique identifier for the information contained in a
Next Hop Resolution Request and its associated Next Hop Resolution
Reply, and any subsequent Purge. This value can be used by the
source to aid in matching a Next Hop Resolution Request with a Next
Hop Resolution Reply. This value could also be sent across a
virtual circuit (in SVC environments) to aid in matching NHRP
transactions with virtual circuits (this use is for further study).
The value is taken from a 32 bit counter that is incremented each
time a new Next Hop Resolution Request is transmitted. The same
value MUST be used when sending another Next Hop Resolution Request
for the same destination when a previous Next Hop Resolution
Request is still active or pending, i.e., when retransmitting a
Next Hop Resolution Request because a Next Hop Resolution Reply was
not received, or when refreshing an existing entry to avoid holding
timer expiration. A new value MUST be used when sending a Next Hop
Resolution Request when no cache entry is present, or a previous
cache entry was deleted for any reason.
Maximum Transmission Unit
This field gives the maximum transmission unit for the target
station. This field is ignored in Next Hop Resolution Requests and
should be set to 0. A possible use of this field in the Next Hop
Resolution Request packet is for the Next Hop Resolution Requester
to ask for a target MTU. This use is for further study.
Holding Time
The Holding Time field specifies the number of seconds for which
the client NBMA information (the information of the client issuing
the Next Hop Resolution Request) is considered to be valid. The
contents of this field along with the source address information
MAY be cached by transit NHSs. The holding time should be set to
the remaining time left in the client's registration with its
server. If this field is set to 0 then transit NHSs MUST not cache
the client's NBMA information.
Source NBMA Address
The Source NBMA address field is the address of the source station
which is sending the Next Hop Resolution Request. If the field's
length as specified in ar$shtl is 0 then no storage is allocated
for this address at all.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the source
station which is sending the Next Hop Resolution Request. If the
field's length as specified in ar$sstl is 0 then no storage is
allocated for this address at all.
Katz, Piscitello, Cole, Luciani [Page 16]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Source Protocol Address
This is the protocol address of the station which is sending the
Next Hop Resolution Request.
Destination Protocol Address
This is the protocol address of the station for which the NBMA next
hop is desired.
(The NBMA address/subaddress form allows combined E.164/NSAPA form of
NBMA addressing. For NBMA technologies without a subaddress concept,
the subaddress field is always ZERO length and ar$sstl = 0.)
5.2.2 NHRP Next Hop Resolution Reply
The NHRP Next Hop Resolution Reply packet has a type code of 2. The
Mandatory Part has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len |Q|A|P|B| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Maximum Transmission Unit | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NH Addr T/L | NH SAddr T/L | NH Proto Len | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Katz, Piscitello, Cole, Luciani [Page 17]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Next Hop Resolution Request/Reply Flags
Q
Copied from the Next Hop Resolution Request. Set if the Next Hop
Resolution Requester is a router; clear if it is a host.
A
Set if the next hop in the Next Hop Resolution Reply is
authoritative; clear if the Next Hop Resolution Reply is non-
authoritative.
P
Set if the Next Hop Resolution Reply is positive; clear if the
Next Hop Resolution Reply is negative.
B
Set if the association between the destination and the next hop
information is guaranteed to be stable for the lifetime of the
information (the holding time). This is the case if the Next Hop
protocol address identifies the destination (though it may be
different in value than the Destination address if the
destination system has multiple addresses) or if the destination
is not connected directly to the NBMA subnetwork but the egress
router to that destination is guaranteed to be stable (such as
when the destination is immediately adjacent to the egress router
through a non-NBMA interface). This information affects caching
strategies (see section 6.2).
An NHS is not allowed to send a Next Hop Resolution Reply to an
Next Hop Resolution Request for authoritative information with
cached information, but may do so for an NHRP Next Hop Resolution
Request which indicates a request for non-authoritative
information. An NHS may send an Next Hop Resolution Reply to an
Next Hop Resolution Request for non-authoritative information with
authoritative information.
Request ID
A value which, when coupled with the address of the source,
provides a unique identifier for the information contained in a
Next Hop Resolution Request and its associated Next Hop Resolution
Reply, and any subsequent Purge. This value can be used by the
source to aid in matching a Next Hop Resolution Request with a Next
Hop Resolution Reply. This value could also be sent across a
virtual circuit (in SVC environments) to aid in matching NHRP
Katz, Piscitello, Cole, Luciani [Page 18]
INTERNET-DRAFT NBMA NHRP Expires June 1996
transactions with virtual circuits (this use is for further study).
The value is taken from a 32 bit counter that is incremented each
time a new Next Hop Resolution Request is transmitted. The same
value MUST be used when sending another Next Hop Resolution Request
for the same destination when a previous Next Hop Resolution
Request is still active or pending, i.e., when retransmitting a
Next Hop Resolution Request because a Next Hop Resolution Reply was
not received, or when refreshing an existing entry to avoid holding
timer expiration. A new value MUST be used when sending a Next Hop
Resolution Request when no cache entry is present, or a previous
cache entry was deleted for any reason.
Maximum Transmission Unit
This field gives the maximum transmission unit for the Next Hop
information supplied in the mandatory part of the packet. If this
value is 0 then either the default MTU is used or the MTU
negotiated via signaling is used if such negotiation is possible
for the given NBMA.
Holding Time
The Holding Time field specifies the number of seconds for which
the Next Hop NBMA information specified in the mandatory part of
the packet is considered to be valid. Cached information SHALL be
discarded when the holding time expires. This field must be set to
0 on a NAK.
NH Addr T/L
Type & length of next hop NBMA address specified in the mandatory
part of the packet. This field is interpreted in the context of the
'address family number'[6] indicated by ar$afn (e.g., ar$afn=0x0003
for ATM).
NH SAddr T/L
Type & length of next hop NBMA subaddress specified in the
mandatory part of the packet. This field is interpreted in the
context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0015 for ATM makes the address an E.164 and the
subaddress an ATM Forum NSAP address). When an NBMA technology has
no concept of a subaddress the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
NH Proto Len
This field holds the length in octets of the Next Hop Protocol
Address specified in the mandatory part of the packet (additional
next hop entries may be specified in the Additional Next Hop
Entries Extension (see Section 5.2.9)).
Katz, Piscitello, Cole, Luciani [Page 19]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Preference
This field specifies the preference of the Next Hop entry specified
in the mandatory part of the packet. This preference value is
relative to other Next Hop entries in this NHRP Next Hop Resolution
Reply packet which may be by the Additional Next Hop Entries
Extension (see Section 5.3.9) for the given internetworking
protocol. Higher values indicate higher preference. Action taken
when multiple next hop entries have the highest preference value is
a local matter. Set to 0 on a NAK.
Source NBMA Address
The Source NBMA address field is the address of the source station
which sent the Next Hop Resolution Request. If the field's length
as specified in ar$shtl is 0 then no storage is allocated for this
address at all.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the source
station which sent the Next Hop Resolution Request. If the field's
length as specified in ar$sstl is 0 then no storage is allocated
for this address at all.
Source Protocol Address
This is the protocol address of the station which sent the Next Hop
Resolution Request.
Destination Protocol Address
This is the protocol address of the station for which the NBMA next
hop is desired.
(The NBMA address/subaddress form allows combined E.164/NSAPA form
of NBMA addressing. For NBMA technologies without a subaddress
concept, the subaddress field is always ZERO length and ar$sstl =
0.)
The following is the Next Hop entry as specified in the Mandatory
Part of the packet:
Next Hop NBMA Address
This is the NBMA address of the station that is the next hop for
packets bound for the internetworking layer address specified.
Next Hop NBMA SubAddress
This is the NBMA subaddress of the station that is the next hop
for packets bound for the internetworking layer address
specified.
Next Hop Protocol Address
Katz, Piscitello, Cole, Luciani [Page 20]
INTERNET-DRAFT NBMA NHRP Expires June 1996
This internetworking layer address specifies the next hop. This
will be the address of the destination host if it is directly
attached to the NBMA subnetwork, or the egress router if it is
not directly attached.
There may be multiple Next Hop entries returned in the Next Hop
Resolution Reply by including the Additional Next Hop Entries
Extension. See Section 5.3.9 for use of these entries. The most
preferable Next Hop must be specified in the mandatory part of the
Next Hop Resolution Reply.
Any extensions present in the Next Hop Resolution Request packet MUST
be present in the NHRP Next Hop Resolution Reply packet, except for
the case of unrecognized non-Compulsory extensions.
If an unsolicited NHRP Next Hop Resolution Reply packet is received,
an Error Indication of type Invalid Next Hop Resolution Reply
Received SHOULD be sent in response.
5.2.3 NHRP Registration Request
The NHRP Registration Request is sent from a station to an NHS to
notify the NHS of the station's NBMA information. It has a Type code
of 3. The Mandatory Part has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Register Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Katz, Piscitello, Cole, Luciani [Page 21]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Request ID
A value which, when coupled with the address of the source,
provides a unique identifier for the information contained in an
NHRP Registration Request packet. This value is copied directly
from an NHRP Registration Request packet into the associated
Registration Reply. This value could also be sent across a virtual
circuit (in SVC environments) to aid in matching the NHRP
transactions with virtual circuits (this use is for further study).
Register Holding Time
The Register Holding Time field specifies the number of seconds for
which the registered NBMA information is considered to be valid.
Cached information SHALL be discarded when the holding time
expires.
Source NBMA Address
The Source NBMA address field is the address of the source station
which is sending the NHRP Registration Request.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the source
station which is sending the NHRP Registration Request. If the
field's length as specified in ar$sstl is 0 then no storage is
allocated for this address at all.
Source Protocol Address
This is the protocol address of the station which is sending the
NHRP Registration Request.
Destination Protocol Address
This is the protocol address of the NHS for which the source NBMA
next hop information is being registered.
This packet is used to register a station's Protocol and NBMA
addresses with its NHSs, as configured or known through conventional
routing means. This allows static configuration information to be
reduced; the NHSs need not be configured with the identities of all
of the stations that they serve. If an NHS receives an NHRP
Registration Request packet for a station that it does not serve and
that packet has a Destination Protocol Address which is not the
protocol address of the NHS that is currently inspecting the packet
then the NHS inspecting the packet MUST forward the registration
along the routed path to the Destination Protocol Address.
Katz, Piscitello, Cole, Luciani [Page 22]
INTERNET-DRAFT NBMA NHRP Expires June 1996
It is possible that a misconfigured station will attempt to register
with the wrong NHS (i.e., one that cannot serve it due to policy
constraints or routing state). If this is the case, the NHS MUST
reply with a NAK-ed Registration Reply of type Can't Serve This
Address.
If an NHS cannot serve a station due to a lack of resources, the NHS
MUST reply with a NAK-ed Registration Reply of type Registration
Overflow.
In order to keep the registration entry from being discarded, the
station MUST re-send the NHRP Registration Request packet often
enough to refresh the registration, even in the face of occasional
packet loss. It is recommended that the NHRP Registration Request
packet be sent at an interval equal to one-third of the Holding Time
specified therein.
5.2.4 NHRP Registration Reply
The NHRP Registration Reply is sent by an NHS to a client in response
to that client's NHRP Registration Request. If the NAK Code field has
anything other than 0 zero in it then the NHRP Registration Reply is
a NAK otherwise the reply is an ACK. The NHRP Registration Reply has
a Type code of 4. Its mandatory part has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAK Code | unused | Register Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Katz, Piscitello, Cole, Luciani [Page 23]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Request ID
A value which, when coupled with the address of the source,
provides a unique identifier for the information contained in an
NHRP Registration Reply packet. This value is copied directly from
an NHRP Registration Request packet into the associated NHRP
Registration Reply. This value could also be sent across a virtual
circuit (in SVC environments) to aid in matching NHRP transactions
with virtual circuits (this use is for further study).
NAK Code
If this field is set to zero then this packet contains a positively
acknowledged NHRP Registration Reply. If this field contains any
other value then this contains an NHRP Registration Reply NAK which
means that the internetworking layer to NBMA address binding was
not stored at the client's NHS. Currently defined NAK Codes are as
follows:
4 - Can't Serve This Address
An NHS may refuse an NHRP Registration Request attempt for
administrative reasons. If so, the NHS MUST send an NHRP
Registration Reply which contains a NAK code of 4.
5 - Registration Overflow
If an NHS cannot serve a station due to a lack of resources,
the NHS MUST reply with a NAKed NHRP Registration Reply which
contains a NAK code of 5.
Register Holding Time
The Register Holding Time field specifies the number of seconds for
which the registered NBMA information is considered to be valid.
Cached information SHALL be discarded when the holding time
expires.
Source NBMA Address
The Source NBMA address field is the address of the source station
which sent the Next Hop Registration Request.
Source NBMA SubAddress
The Source NBMA subaddress field is the subaddress of the source
station which sent the Next Hop Registration Request. If the
field's length as specified in ar$sstl is 0 then no storage is
allocated for this address at all.
Katz, Piscitello, Cole, Luciani [Page 24]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Source Protocol Address
This is the protocol address of the station which sent the NHRP
Registration Request.
Destination Protocol Address
This is the protocol address of the NHS in which the client is
attempting to register the client's NBMA information.
This packet is used to register a station's Protocol and NBMA
addresses with its neighboring NHSs, as configured or known through
conventional routing means. This allows static configuration
information to be reduced; the NHSs need not be configured with the
identities of all of the stations that they serve. If an NHS receives
an NHRP Registration Request packet for a station that it does not
serve and that packet has a Destination Protocol Address which is not
the protocol address of the NHS that is currently inspecting the
packet then the NHS inspecting the packet MUST forward the
registration along the routed path to the Destination Protocol
Address.
It is possible that a misconfigured station will attempt to send a
Next Hop Registration Request to the wrong NHS (i.e., one that cannot
serve it due to policy constraints or routing state). If this is the
case, the NHS MUST reply with a NAK-ed NHRP Registration Reply of
type Can't Serve This Address.
If an NHS cannot serve a station due to a lack of resources, the NHS
MUST reply with a NAK-ed NHRP Registration Reply of type Registration
Overflow.
In order to keep the client's registration entry in the client's NHS
from being timed out, the station MUST re-send the NHRP Registration
Request packet often enough to refresh the registration entry, even
in the face of occasional packet loss. It is recommended that the
NHRP Registration Request packet be sent at an interval equal to
one-third of the Holding Time specified therein.
5.2.5 NHRP Purge Request
The NHRP Purge Request packet is sent in order to invalidate cached
information in a station. The NHRP Purge Request packet has a type
code of 5. The Mandatory Part has the following format:
Katz, Piscitello, Cole, Luciani [Page 25]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len |Trgt Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Target Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Trgt Proto Len
This field holds the length in octets of the Target Protocol
Address.
Source NBMA Address
The Source NBMA address field is the address of the source station
which is sending the NHRP Purge Request.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the source
station which is sending the NHRP Purge Request. If its length as
specified in ar$sstl is 0 then no storage is allocated for this
address at all.
Source Protocol Address
The address of the station which is sending the NHRP Purge Request.
Destination Protocol Address
The address of the station that will be receiving the NHRP Purge
Request.
Target Protocol Address
The address which is to be purged from the receiver's database.
Katz, Piscitello, Cole, Luciani [Page 26]
INTERNET-DRAFT NBMA NHRP Expires June 1996
An NHRP Purge Request packet is sent from an NHS to a station to
cause it to delete previously cached information. This is done when
the information may be no longer valid (typically when the NHS has
previously provided next hop information for a station that is not
directly connected to the NBMA subnetwork, and the egress point to
that station may have changed).
An NHRP Purge Request packet may also be sent from a client to an NHS
with which the client had previously registered. This allows for a
client to invalidate it's registration with NHRP before it would
otherwise expire via the holding timer.
The station sending the NHRP Purge Request MAY periodically
retransmit the NHRP Purge Request until either NHRP Purge Request is
acknowledged or until the holding time of the information being
purged has expired. Retransmission strategies are for further
investigation.
When a station receives an NHRP Purge Request, it MUST discard any
previously cached information that matches the Target Protocol
Address.
An NHRP Purge Reply MUST be returned for the NHRP Purge Request even
if the station does not have a matching cache entry.
If the station wishes to reestablish communication with the
destination shortly after receiving an NHRP Purge Request, it should
make an authoritative Next Hop Resolution Request in order to avoid
any stale cache entries that might be present in intermediate NHSs
(See section 6.2.2.). It is recommended that authoritative Next Hop
Resolution Requests be made for the duration of the holding time of
the old information.
5.2.6 NHRP Purge Reply
The NHRP Purge Reply packet is sent in order to assure the sender of
an NHRP Purge Request that all cached information of the specified
type has been purged from the station sending the reply. The NHRP
Purge packet has a type code of 6. The Mandatory Part has the
following format:
Katz, Piscitello, Cole, Luciani [Page 27]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len |Trgt Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Target Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Trgt Proto Len
This field holds the length in octets of the Target Protocol
Address.
Source NBMA Address
The Source NBMA address field is the address of the source station
which sent the NHRP Purge Request.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the source
station which sent the NHRP Purge Request. If its length as
specified in ar$sstl is 0 then no storage is allocated for this
address at all.
Source Protocol Address
The address of the station which sent the NHRP Purge Request.
Destination Protocol Address
The address of the station which is sending the NHRP Purge Reply.
Target Protocol Address
The address which is to be purged from the receiver's database.
Katz, Piscitello, Cole, Luciani [Page 28]
INTERNET-DRAFT NBMA NHRP Expires June 1996
An NHRP Purge Request packet is sent from an NHS to a station to
cause it to delete previously cached information. This is done when
the information may be no longer valid (typically when the NHS has
previously provided next hop information for a station that is not
directly connected to the NBMA subnetwork, and the egress point to
that station may have changed).
An NHRP Purge Request packet may also be sent from a client to an NHS
with which the client had previously registered. This allows for a
client to invalidate it's registration with NHRP before it would
otherwise expire via the holding timer.
The station sending the NHRP Purge Request MAY periodically
retransmit the NHRP Purge Request until it is acknowledged, or until
the holding time of the information being purged has expired.
Retransmission strategies are for further investigation.
When a station receives an NHRP Purge Request, it MUST discard any
previously cached information that matches the Target Protocol
Address.
An NHRP Purge Reply MUST be returned as a result of receiving an NHRP
Purge Request even if the station does not have a matching cache
entry.
If the station wishes to reestablish communication with the
destination shortly after receiving an NHRP Purge Request, it should
make an authoritative Next Hop Resolution Request in order to avoid
any stale cache entries that might be present in intermediate NHSs.
(See section 6.2.2.) It is recommended that authoritative Next Hop
Resolution Requests be made for the duration of the holding time of
the old information.
5.2.7 NHRP Error Indication
The NHRP Error Indication is used to convey error indications to the
sender of an NHRP packet. It has a type code of 6. The Mandatory
Part has the following format:
Katz, Piscitello, Cole, Luciani [Page 29]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Error Code | Error Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Contents of NHRP Packet in error (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Error Code
An error code indicating the type of error detected, chosen from
the following list:
1 - Unrecognized Extension
When the Compulsory bit of an extension in NHRP packet is set,
the NHRP packet cannot be processed unless the extension has
been processed. The responder MUST return an NHRP Error
Indication of type Unrecognized Extension if it is incapable of
processing the extension. However, if a transit NHS (one which
is not going to generate a reply) detects an unrecognized
extension, it SHALL ignore the extension.
2 - Subnetwork ID Mismatch
This error occurs when the current station receives an NHRP
packet whose NBMA subnetwork identifier matches none of the
locally known identifiers for the NBMA subnetwork on which the
packet is received.
3 - NHRP Loop Detected
Katz, Piscitello, Cole, Luciani [Page 30]
INTERNET-DRAFT NBMA NHRP Expires June 1996
A Loop Detected error is generated when it is determined that
an NHRP packet is being forwarded in a loop.
8 - NHRP SDU Size Exceeded
If the SDU size of the NHRP packet exceeds the maximum SDU size
of the NBMA network, this error is returned.
9 - Invalid Extension
If an NHS finds an extension in a packet which is inappropriate
for the packet type, an error is sent back to the sender with
Invalid Extension as the code.
10- Invalid Next Hop Resolution Reply Received
If a client receives a Next Hop Resolution Reply for a Next Hop
Resolution Request which it believes it did not make then an
error packet is sent to the station making the reply with an
error code of Invalid Reply Received.
Error Offset
The offset in octets into the NHRP packet, starting at the NHRP
Fixed Header, at which the error was detected.
Source NBMA Address
The Source NBMA address field is the address of the station which
observed the error.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the station
which observed the error. If the field's length as specified in
ar$sstl is 0 then no storage is allocated for this address at all.
Source Protocol Address
This is the protocol address of the station which issued the Error
packet.
Destination Protocol Address
This is the protocol address of the station which sent the packet
which was found to be in error.
An NHRP Error Indication packet SHALL NEVER be generated in response
to another NHRP Error Indication packet. When an NHRP Error
Indication packet is generated, the offending NHRP packet SHALL be
discarded. In no case should more than one NHRP Error Indication
packet be generated for a single NHRP packet.
Katz, Piscitello, Cole, Luciani [Page 31]
INTERNET-DRAFT NBMA NHRP Expires June 1996
If an NHS sees its own Protocol and NBMA Addresses in the Source NBMA
and Source Protocol address fields of a transiting NHRP Error
Indication packet then the NHS will quietly drop the packet and do
nothing (this scenario would occur when the NHRP Error Indication
packet was itself in a loop).
Note that no extensions may be added to an NHRP Error Indication.
5.3 Extensions Part
In the following, unless otherwise stated explicitly, the term
"request" refers generically to any of the NHRP packet types which
are "requests". Also, unless otherwise stated explicitly, the term
"reply" refers generically to any of the NHRP packet types which are
"replies".
The Extensions Part, if present, carries one or more extensions in
{Type, Length, Value} triplets. Extensions are only present in a
"reply" if they were present in the corresponding "request";
therefore, minimal NHRP station implementations that do not act as an
NHS and do not transmit extensions need not be able to receive
extensions. An implementation that is incapable of processing
extensions SHALL return an NHRP Error Indication of type Unrecognized
Extension when it receives an NHRP packet containing extensions.
Extensions have the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C|u| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
C
"Compulsory." If clear, and the NHS does not recognize the type
code, the extension may safely be ignored. If set, and the NHS
does not recognize the type code, the NHRP "request" is considered
to be in error. (See below for details.)
u
Unused and must be set to zero.
Type
The extension type code (see below). The extension type is not
Katz, Piscitello, Cole, Luciani [Page 32]
INTERNET-DRAFT NBMA NHRP Expires June 1996
qualified by the Compulsory bit, but is orthogonal to it.
Length
The length in octets of the value (not including the Type and
Length fields; a null extension will have only an extension header
and a length of zero).
When extensions exist, the extensions list is terminated by the Null
TLV, having Type = 0 and Length = 0.
Extensions may occur in any order, but any particular extension type
(except for the vendor-private extension) may occur only once in an
NHRP packet. The vendor-private extension may occur multiple times
in a packet in order to allow for extensions which do not share the
same vendor ID to be represented.
The Compulsory bit provides for a means to add to the extension set.
If the bit is set, the NHRP message cannot be properly processed by
the station responding to the message (e.g., the station that would
issue a Next Hop Resolution Reply in response to a Next Hop
Resolution Request) without processing the extension. As a result,
the responder MUST return an NHRP Error Indication of type
Unrecognized Extension. If the Compulsory bit is clear then the
extension can be safely ignored; however, if an ignored extension is
in a "request" then it MUST be returned, unchanged, in the
corresponding "reply" packet type.
If a transit NHS (one which is not going to generate a "reply")
detects an unrecognized extension, it SHALL ignore the extension. If
the Compulsory bit is set, the transit NHS MUST NOT cache the
information contained in the packet and MUST NOT identify itself as
an egress router (in the Forward Record or Reverse Record
extensions). Effectively, this means, if a transit NHS encounters an
extension which it cannot process and which has the Compulsory bit
set then that NHS MUST NOT participate in any way in the protocol
exchange other than acting as a forwarding agent.
5.3.0 The End Of Extensions
Compulsory = 1
Type = 0
Length = 0
When extensions exist, the extensions list is terminated by the End
Of Extensions/Null TLV.
Katz, Piscitello, Cole, Luciani [Page 33]
INTERNET-DRAFT NBMA NHRP Expires June 1996
5.3.1 Destination Prefix Length
Compulsory = 0
Type = 1
Length = 1
This extension is used to indicate that the information carried in an
NHRP packet pertains to an equivalence class of internetwork layer
addresses rather than just a single internetwork layer address
specified. All internetwork layer addresses that match the first
"Prefix Length" bit positions for the specific internetwork layer
address are included in the equivalence class.
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In the case of an Next Hop Resolution Request, if equivalence
information is desired from the Next Hop Resolution Reply then the
Destination Prefix Length extension is included in the Next Hop
Resolution Request and the Prefix Length value is coded as 0xffff.
For the Next Hop Resolution Reply, the Prefix Length is set to the
length of the prefix of the Next Hop Protocol Address present in the
mandatory part of the packet.
In the case of an NHRP Registration Request, if equivalence
information is desired to be registered then the Destination Prefix
Length extension is included in the NHRP Registration Request with
the Prefix Length value set to the length of the prefix of the
equivalence information for the Source Protocol Address. In Next Hop
Registration Reply, the Destination Prefix Length extension is merely
copied unchanged.
In the case of an Next Hop Purge Request, if equivalence information
is desired then the Prefix Length value is set to the length of the
prefix of the Target Protocol Address which represents the
equivalence information to be purged. In Next Hop Purge Reply, the
Destination Prefix Length extension is merely copied unchanged.
5.3.2 NBMA Subnetwork ID Extension
Compulsory = 1
Type = 2
Length = variable
Katz, Piscitello, Cole, Luciani [Page 34]
INTERNET-DRAFT NBMA NHRP Expires June 1996
This extension is used to carry one or more identifiers for the NBMA
subnetwork. This can be used as a validity check to ensure that an
NHRP packet does not leave a particular NBMA subnetwork. The
extension is placed in a "request" packet with an ID value of zero.
The first NHS along the routed path fills in the field with the
identifier(s) for the NBMA subnetwork.
Multiple NBMA Subnetwork IDs may be used as a transition mechanism
while NBMA Subnetworks are being split or merged.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NBMA Subnetwork ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
...
Each identifier consists of a 32 bit globally unique value assigned
to the NBMA subnetwork. This value may be chosen from the
internetworking layer address space administered by the operators of
the NBMA subnetwork if such an address can fit into a 32 bit field.
This value is used for identification only, not for routing or any
other purpose.
Each NHS processing a "request" or "reply" SHALL verify these values.
If the value is not zero and none of the values matches the NHS's
NBMA Subnetwork ID, the NHS SHALL return an NHRP Error Indication to
the entity identified in Source Protocol Address if the packet type
is a "request" and to the Destination Protocol Address if the packet
type is a "reply". The error indicated in this case is "Subnetwork
ID Mismatch". The packet is discarded by the station sending the
NHRP Error Indication.
When an NHS is building a "reply" and the NBMA Subnetwork ID
extension is present in the correspond "request" then the NBMA
Subnetwork ID extension SHALL be copied from the "request" to the
"reply".
5.3.3 Responder Address Extension
Compulsory = 1
Type = 3
Length = 4
This extension is used to determine the address of the NHRP
responder; i.e., the entity that generates the appropriate "reply"
packet for a given "request" packet. In the case of an Next Hop
Katz, Piscitello, Cole, Luciani [Page 35]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Resolution Request, the station responding may be different (in the
case of cached replies) than the system identified in the Next Hop
field of the Next Hop Resolution Reply. Further, this extension may
aid in detecting loops in the NHRP forwarding path.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Res Addr T/L | Res SAddr T/L| Res Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Responder NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Responder NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Responder Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Holding Time
The Holding Time field specifies the number of seconds for which
the NBMA information is considered to be valid. Cached information
SHALL be discarded when the holding time expires.
Res Addr T/L
Type & length of the responder NHS's NBMA address interpreted in
the context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0003 for ATM). When the address length is
specified as 0 no storage is allocated for the address.
Res SAddr T/L
Type & length of responder NHS's NBMA subaddress interpreted in the
context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0015 for ATM makes the address an E.164 and the
subaddress an ATM Forum NSAP address). When an NBMA technology has
no concept of a subaddress, the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
Res Proto Len
This field holds the length in octets of responding NHS's Protocol
Address.
Responder NBMA Address
This is the NBMA address of the responding NHS.
Responder NBMA SubAddress
This is the NBMA subaddress of the responding NHS.
Katz, Piscitello, Cole, Luciani [Page 36]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Responder Protocol Address
This is the Protocol Address of responding NHS.
If a "requester" desires this information, the "requester" SHALL
include this extension with a value of zero. Note that this implies
that no storage is allocated for the Holding Time and Type/Length
fields until the "Value" portion of the extension is filled out.
If an NHS is generating a "reply" packet in response to a "request"
containing this extension, the NHS SHALL include this extension,
containing its protocol address in the "reply". If an NHS has more
than one protocol address, it SHALL use the same protocol address
consistently in all of the Responder Address, Forward NHS Record, and
Reverse NHS Record extensions. The choice of which of several
protocol address to include in this extension is a local matter.
If an NHRP Next Hop Resolution Reply packet being forwarded by an NHS
contains a protocol address of that NHS in the Responder Address
Extension then that NHS SHALL generate an NHRP Error Indication of
type "NHRP Loop Detected" and discard the Next Hop Resolution Reply.
If an NHRP Next Hop Resolution Reply packet is being returned by an
intermediate NHS based on cached data, it SHALL place its own address
in this extension (differentiating it from the address in the Next
Hop field).
5.3.4 NHRP Forward Transit NHS Record Extension
Compulsory = 1
Type = 4
Length = variable
The NHRP Forward Transit NHS record contains a list of transit NHSs
through which a "request" has traversed. Each NHS SHALL append to
the extension a Forward Transit NHS element (as specified below)
containing its Protocol address The extension length field and the
ar$chksum fields SHALL be adjusted appropriately.
The responding NHS, as described in Section 5.3.3, SHALL NOT update
this extension.
In addition, NHSs that are willing to act as egress routers for
packets from the source to the destination SHALL include information
about their NBMA Address.
The Forward Transit NHS element has the following form:
Katz, Piscitello, Cole, Luciani [Page 37]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Addr T/L | NHS SAddr T/L| NHS Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Holding Time
The Holding Time field specifies the number of seconds for which
the NBMA information is considered to be valid. Cached information
SHALL be discarded when the holding time expires.
NHS Addr T/L
Type & length of the transit NHS's NBMA address interpreted in the
context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0003 for ATM). When the address length is
specified as 0 no storage is allocated for the address.
NHS SAddr T/L
Type & length of the transit NHS's NBMA subaddress interpreted in
the context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0015 for ATM makes the address an E.164 and the
subaddress an ATM Forum NSAP address). When an NBMA technology has
no concept of a subaddress the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
NHS Proto Len
This field holds the length in octets of the transit NHS's Protocol
Address.
NHS NBMA Address
This is the NBMA address of the transit NHS.
NHS NBMA SubAddress
This is the NBMA subaddress of the transit NHS.
NHS Protocol Address
This is the Protocol Address of the transit NHS.
If a "requester" wishes to obtain this information, it SHALL include
Katz, Piscitello, Cole, Luciani [Page 38]
INTERNET-DRAFT NBMA NHRP Expires June 1996
this extension with a length of zero. Note that this implies that no
storage is allocated for the Holding Time and Type/Length fields
until the "Value" portion of the extension is filled out.
If an NHS has more than one Protocol address, it SHALL use the same
Protocol address consistently in all of the Responder Address,
Forward NHS Record, and Reverse NHS Record extensions. The choice of
which of several Protocol addresses to include in this extension is a
local matter.
If a "request" that is being forwarded by an NHS contains the
Protocol Address of that NHS in one of the Forward Transit NHS
elements then the NHS SHALL generate an NHRP Error Indication of type
"NHRP Loop Detected" and discard the "request".
5.3.5 NHRP Reverse Transit NHS Record Extension
Compulsory = 1
Type = 5
Length = variable
The NHRP Reverse Transit NHS record contains a list of transit NHSs
through which a "reply" has traversed. Each NHS SHALL append a
Reverse Transit NHS element (as specified below) containing its
Protocol address to this extension. The extension length field and
ar$chksum SHALL be adjusted appropriately.
The responding NHS, as described in Section 5.3.3, SHALL NOT update
this extension.
In addition, NHSs that are willing to act as egress routers for
packets from the source to the destination SHALL include information
about their NBMA Address.
The Reverse Transit NHS element has the following form:
Katz, Piscitello, Cole, Luciani [Page 39]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Addr T/L | NHS SAddr T/L| NHS Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Holding Time
The Holding Time field specifies the number of seconds for which
the NBMA information is considered to be valid. Cached information
SHALL be discarded when the holding time expires.
NHS Addr T/L
Type & length of the responding NHS's NBMA address interpreted in
the context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0003 for ATM). When the address length is
specified as 0 no storage is allocated for the address.
NHS SAddr T/L
Type & length of the responding NHS's NBMA subaddress interpreted
in the context of the 'address family number'[6] indicated by
ar$afn (e.g., ar$afn=0x0015 for ATM makes the address an E.164 and
the subaddress an ATM Forum NSAP address). When an NBMA technology
has no concept of a subaddress the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
NHS Proto Len
This field holds the length in octets of the transit NHS's Protocol
Address.
NHS NBMA Address
This is the NBMA address of the transit NHS.
NHS NBMA SubAddress
This is the NBMA subaddress of the transit NHS.
NHS Protocol Address
This is the Protocol Address of the transit NHS.
If a "requester" wishes to obtain this information, it SHALL include
Katz, Piscitello, Cole, Luciani [Page 40]
INTERNET-DRAFT NBMA NHRP Expires June 1996
this extension with a length of zero. Note that this implies that no
storage is allocated for the Holding Time and Type/Length fields
until the "Value" portion of the extension is filled out.
If an NHS has more than one Protocol address, it SHALL use the same
Protocol address consistently in all of the Responder Address,
Forward NHS Record, and Reverse NHS Record extensions. The choice of
which of several Protocol addresses to include in this extension is a
local matter.
If a "reply" that is being forwarded by an NHS contains the Protocol
Address of that NHS in one of the Reverse Transit NHS elements then
the NHS SHALL generate an NHRP Error Indication of type "NHRP Loop
Detected" and discard the "reply".
Note that this information may be cached at intermediate NHSs; if
so, the cached value SHALL be used when generating a reply.
5.3.6 NHRP QoS Extension
Compulsory = 0
Type = 6
Length = variable
The NHRP QoS Extension is carried in Next Hop Resolution Request
packets to indicate the desired QoS of the path to the indicated
destination. This information may be used to help select the
appropriate NBMA Next Hop.
It may also be carried in NHRP Register Request packets to indicate
the QoS to which the registration applies.
The syntax and semantics of this extension are TBD; alignment with
resource reservation may be useful.
5.3.7 NHRP Authentication Extension
Compulsory = 1
Type = 7
Length = variable
The NHRP Authentication Extension is carried in NHRP packets to
convey authentication information between NHRP speakers. The
Authentication Extension may be included in any NHRP "request" or
"reply".
Katz, Piscitello, Cole, Luciani [Page 41]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Except in the case of an NHRP Registration Request/Reply
Authentication is done pairwise on an NHRP hop-by-hop basis; i.e.,
the authentication extension is regenerated at each hop. In the case
of an NHRP Registration Request/Reply, the Authentication is checked
on an end-to-end basis rather than hop-by-hop. If a received packet
fails the authentication test, the station SHALL generate an Error
Indication of type "Authentication Failure" and discard the packet.
Note that one possible authentication failure is the lack of an
Authentication Extension; the presence or absence of the
Authentication Extension is a local matter.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Authentication Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+ Authentication Data... -+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Authentication Type field identifies the authentication method in
use. Currently assigned values are:
1 - Cleartext Password
2 - Keyed MD5
All other values are reserved.
The Authentication Data field contains the type-specific
authentication information.
In the case of Cleartext Password Authentication, the Authentication
Data consists of a variable length password.
In the case of Keyed MD5 Authentication, the Authentication Data
contains the 16 byte MD5 digest of the entire NHRP packet, including
the encapsulated protocol's header, with the authentication key
appended to the end of the packet. The authentication key is not
transmitted with the packet.
Distribution of authentication keys is outside the scope of this
document.
5.3.8 NHRP Vendor-Private Extension
Compulsory = 0
Katz, Piscitello, Cole, Luciani [Page 42]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Type = 8
Length = variable
The NHRP Vendor-Private Extension is carried in NHRP packets to
convey vendor-private information or NHRP extensions between NHRP
speakers.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor ID | Data.... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Vendor ID
802 Vendor ID as assigned by the IEEE [6]
Data
The remaining octets after the Vendor ID in the payload are
vendor-dependent data.
This extension may be added to any "request" or "reply" packet and it
is the only extension that may be included multiple times. If the
receiver does not handle this extension, or does not match the Vendor
ID in the extension then the extension may be completely ignored by
the receiver. If a Vendor Private Extension is included in a
"request" then is must be copied in the corresponding "reply".
5.3.9 Additional Next Hop Entries Extension
Compulsory = 0
Type = 9
Length = variable
This extension may be used to return multiple Next Hop entries in a
single NHRP Reply packet. This extension MUST only be used for
positive replies. The preference values are used to specify the
relative preference of the entries contained in the extension. The
same next Hop Protocol address may be associated with multiple NBMA
addresses. Load-splitting may be performed over the addresses, given
equal preference values, and the alternative addresses may be used in
case of connectivity failure in the NBMA subnetwork (such as a failed
call attempt in connection-oriented NBMA subnetworks).
The following shows the format for additional Next Hop Entries:
Katz, Piscitello, Cole, Luciani [Page 43]
INTERNET-DRAFT NBMA NHRP Expires June 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Maximum Transmission Unit | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NH Addr T/L | NH SAddr T/L | NH Proto Len | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
.....................
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Maximum Transmission Unit | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NH Addr T/L | NH SAddr T/L | NH Proto Len | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An NHS is not allowed to reply to an NHRP request for authoritative
information with cached information, but may do so for an NHRP
Request which indicates a request for non-authoritative information.
An NHS may reply to an NHRP request for non-authoritative information
with authoritative information.
Maximum Transmission Unit
This field gives the maximum transmission unit for the target
station. If this value is 0 then either the default MTU is used or
the MTU negotiated via signaling is used if such negotiation is
possible for the given NBMA.
Holding Time
The Holding Time field specifies the number of seconds for which
the Next Hop NBMA information specified in the Next Hop Entry is
considered to be valid. Cached information SHALL be discarded when
the holding time expires. This field must be set to 0 on a NAK.
NH Addr T/L
Type & length of next hop NBMA address specified in the Next Hop
Entry. This field is interpreted in the context of the 'address
family number'[6] indicated by ar$afn (e.g., ar$afn=0x0003 for
Katz, Piscitello, Cole, Luciani [Page 44]
INTERNET-DRAFT NBMA NHRP Expires June 1996
ATM).
NH SAddr T/L
Type & length of next hop NBMA subaddress specified in the Next Hop
Entry. This field is interpreted in the context of the 'address
family number'[6] indicated by ar$afn (e.g., ar$afn=0x0015 for ATM
makes the address an E.164 and the subaddress an ATM Forum NSAP
address). When an NBMA technology has no concept of a subaddress
the subaddress is always null with a length of 0. When the address
length is specified as 0 no storage is allocated for the address.
NH Proto Len
This field holds the length in octets of the Next Hop Protocol
Address specified in the Next Hop Entry.
Preference
This field specifies the preference of the specific Next Hop Entry
relative to other Next Hop entries in this Next Hop Resolution
Reply mandatory part or in the Additional Next Hop Entries
Extension for the given internetworking protocol. Higher values
indicate higher preference. Action taken when multiple next hop
entries have the highest preference value is a local matter.
Next Hop NBMA Address
This is the NBMA address of the station that is the next hop for
packets bound for the internetworking layer address specified.
Next Hop NBMA SubAddress
This is the NBMA subaddress of the station that is the next hop for
packets bound for the internetworking layer address specified.
Next Hop Protocol Address
This internetworking layer address specifies the next hop. This
will be the address of the destination host if it is directly
attached to the NBMA subnetwork, or the egress router if it is not
directly attached.
6. Protocol Operation
In this section, we discuss certain operational considerations of
NHRP.
6.1 Router-to-Router Operation
In practice, the initiating and responding stations may be either
hosts or routers. However, there is a possibility under certain
conditions that a stable routing loop may occur if NHRP is used
Katz, Piscitello, Cole, Luciani [Page 45]
INTERNET-DRAFT NBMA NHRP Expires June 1996
between two routers. In particular, attempting to establish an NHRP
path across a boundary where information used in route selection is
lost may result in a routing loop. Such situations include the loss
of BGP path vector information, the interworking of multiple routing
protocols with dissimilar metrics (e.g, RIP and OSPF), etc. In such
circumstances, NHRP should not be used. This situation can be
avoided if there are no "back door" paths between the entry and
egress router outside of the NBMA subnetwork. Protocol mechanisms to
relax these restrictions are under investigation.
In general it is preferable to use mechanisms, if they exist, in
routing protocols to resolve the egress point when the destination
lies outside of the NBMA subnetwork, since such mechanisms will be
more tightly coupled to the state of the routing system and will
probably be less likely to create loops.
6.2 Cache Management Issues
The management of NHRP caches in the source station, the NHS serving
the destination, and any intermediate NHSs is dependent on a number
of factors.
6.2.1 Caching Requirements
Source Stations
Source stations MUST cache all received Next Hop Resolution Replies
that they are actively using. They also must cache "incomplete"
entries, i.e., those for which a Next Hop Resolution Request has
been sent but which a Next Hop Resolution Reply has not been
received. This is necessary in order to preserve the Request ID
for retries, and provides the state necessary to avoid triggering
Next Hop Resolution Requests for every data packet sent to the
destination.
Source stations MUST purge expired information from their caches.
Source stations MUST purge the appropriate cached information upon
receipt of an NHRP Purge Request packet.
When a station has a co-resident client and NHS, the station may
reply to Next Hop Resolution Requests with information which the
station cached as a result of the station making its own Next Hop
Resolution Requests and receiving its own Next Hop Resolution
Replies as long as the station follows the rules for Transit NHSs
as seen below.
Katz, Piscitello, Cole, Luciani [Page 46]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Serving NHSs
The NHS serving the destination (the one which responds
authoritatively to Next Hop Resolution Requests) SHOULD cache
information about all Next Hop Resolution Requests to which it has
responded if the information in the Next Hop Resolution Reply has
the possibility of changing during its lifetime (so that an NHRP
Purge Request packet can be sent). The NBMA information provided
by the source station in the Next Hop Resolution Request may be
cached for the duration of its holding time. This information is
considered to be stable, since it identifies a station directly
attached to the NBMA subnetwork. An example of unstable
information is NBMA information derived from a routing table, where
that routing table information has not been guaranteed to be stable
through administrative means.
Transit NHSs
A Transit NHS (lying along the NHRP path between the source station
and the responding NHS) may cache information contained in Next Hop
Resolution Request packets that it forwards. A Transit NHS may
cache information contained in Next Hop Resolution Reply packets
that it forwards only if that Next Hop Resolution Reply has the
Stable (B) bit set. It MUST discard any cached information whose
holding time has expired. It may return cached information in
response to non-authoritative Next Hop Resolution Requests only.
6.2.2 Dynamics of Cached Information
NBMA-Connected Destinations
NHRP's most basic function is that of simple NBMA address
resolution of stations directly attached to the NBMA subnetwork.
These mappings are typically very static, and appropriately chosen
holding times will minimize problems in the event that the NBMA
address of a station must be changed. Stale information will cause
a loss of connectivity, which may be used to trigger an
authoritative Next Hop Resolution Request and bypass the old data.
In the worst case, connectivity will fail until the cache entry
times out.
This applies equally to information marked in Next Hop Resolution
Replies as being "stable" (via the "B" bit).
This also applies equally well to source stations that are routers
as well as those which are hosts.
Katz, Piscitello, Cole, Luciani [Page 47]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Note that the information carried in the Next Hop Resolution
Request packet is always considered "stable" because it represents
a station that is directly connected to the NBMA subnetwork.
Destinations Off of the NBMA Subnetwork
If the source of a Next Hop Resolution Request is a host and the
destination is not directly attached to the NBMA subnetwork, and
the route to that destination is not considered to be "stable," the
destination mapping may be very dynamic (except in the case of a
subnetwork where each destination is only singly homed to the NBMA
subnetwork). As such the cached information may very likely become
stale. The consequence of stale information in this case will be a
suboptimal path (unless the internetwork has partitioned or some
other routing failure has occurred).
Strategies for maintaining NHRP cache information in the presence
of dynamic routing changes will be discussed in a separate
document.
6.3 Use of the Destination Prefix Length Extension
A certain amount of care needs to be taken when using the Destination
Prefix Length Extension, in particular with regard to the prefix
length advertised (and thus the size of the equivalence class
specified by it). Assuming that the routers on the NBMA subnetwork
are exchanging routing information, it should not be possible for an
NHS to create a black hole by advertising too large of a set of
destinations, but suboptimal routing (e.g., extra internetwork layer
hops through the NBMA) can result. To avoid this situation an NHS
that wants to send the Destination Prefix Length Extension MUST obey
the following rule:
The NHS examines the Network Layer Reachability Information (NLRI)
associated with the route that the NHS would use to forward towards
the destination (as specified by the Destination internetwork layer
address in the Next Hop Resolution Request), and extracts from this
NLRI the shortest address prefix such that: (a) the Destination
internetwork layer address (from the Next Hop Resolution Request)
is covered by the prefix, (b) the NHS does not have any routes with
NLRI that forms a subset of what is covered by the prefix. The
prefix may then be used for the Destination Prefix Length
Extension.
The NHRP Destination Prefix Length Extension should be used with
restraint, in order to avoid NHRP stations choosing suboptimal
transit paths when overlapping prefixes are available. This
Katz, Piscitello, Cole, Luciani [Page 48]
INTERNET-DRAFT NBMA NHRP Expires June 1996
extension SHOULD only be used in a Next Hop Resolution Reply when
either:
(a) All destinations covered by the prefix are on the NBMA network, or
(b) All destinations covered by the prefix are directly attached to
the NHRP responding station.
For other cases, there may be no single optimal transit path for
destinations encompassed by the address prefix, and an NHRP station
may fail to choose the optimal transit path simply because it is not
aware of all such paths. So for cases not covered by (a) and (b), an
Next Hop Resolution Reply packet should not include the NHRP
Destination Prefix Length Extension.
6.4 Domino Effect
One could easily imagine a situation where a router, acting as an
ingress station to the NBMA subnetwork, receives a data packet, such
that this packet triggers an Next Hop Resolution Request. If the
router forwards this data packet without waiting for an NHRP transit
path to be established, then when the next router along the path
receives the packet, the next router may do exactly the same -
originate its own Next Hop Resolution Request (as well as forward the
packet). In fact such a data packet may trigger Next Hop Resolution
Request generation at every router along the path through an NBMA
subnetwork. We refer to this phenomena as the NHRP "domino" effect.
The NHRP domino effect is clearly undesirable. At best it may result
in excessive NHRP traffic. At worst it may result in an excessive
number of virtual circuits being established unnecessarily.
Therefore, it is important to take certain measures to avoid or
suppress this behavior. NHRP implementations for NHSs MUST provide a
mechanism to address this problem. It is recommended that
implementations provide one or more of the following solutions.
Possibly the most straightforward solution for suppressing the domino
effect would be to require transit routers to be preconfigured not to
originate Next Hop Resolution Requests for data traffic which is
simply being forwarded (not originated). In this case the routers
avoid the domino effect through an administrative policy.
A second possible solution would be to require that when a router
forwards an Next Hop Resolution Request, the router instantiates a
(short-lived) state. This state consists of the route that was used
to forward the Next Hop Resolution Request. If the router receives a
data packet, and the packet triggers an Next Hop Resolution Request
generation by the router, the router checks whether the route to
forward the Next Hop Resolution Request was recently used to forward
Katz, Piscitello, Cole, Luciani [Page 49]
INTERNET-DRAFT NBMA NHRP Expires June 1996
some other Next Hop Resolution Request. If so, then the router
suppresses generation of the new Next Hop Resolution Request (but
still forwards the data packet). This solution also requires that
when a station attempts to originate an Next Hop Resolution Request
the station should send the Next Hop Resolution Request before the
data packet that triggered the origination of the Next Hop Resolution
Request. Otherwise, unnecessary Next Hop Resolution Requests may
still be generated.
A third possible strategy would be to configure a router in such a
way that Next Hop Resolution Request generation by the router would
be driven only by the traffic the router receives over its non-NBMA
interfaces (interfaces that are not attached to an NBMA subnetwork).
Traffic received by the router over its NBMA-attached interfaces
would not trigger NHRP Next Hop Resolution Requests. Just as in the
first case, such a router avoids the NHRP domino effect through
administrative means.
Lastly, rate limiting of Next Hop Resolution Requests may help to
avoid the NHRP domino effect. Intermediate routers which would
otherwise generate unnecessary Next Hop Resolution Requests may
instead suppress such Next Hop Resolution Requests due to the
measured Next Hop Resolution Request rate exceeding a certain
threshold. Of course, such rate limiting would have to be very
aggressive in order to completely avoid the domino effect. Further
work is needed to analyze this solution.
7. Security Considerations
As in any routing protocol, there are a number of potential security
attacks possible. Plausible examples include denial-of-service
attacks, and masquerade attacks using register and purge packets.
The use of authentication on all packets is recommended to avoid such
attacks.
The authentication schemes described in this document are intended to
allow the receiver of a packet to validate the identity of the
sender; they do not provide privacy or protection against replay
attacks.
Detailed security analysis of this protocol is for further study.
8. Discussion
The result of an Next Hop Resolution Request depends on how routing
is configured among the NHSs of an NBMA subnetwork. If the
destination station is directly connected to the NBMA subnetwork and
Katz, Piscitello, Cole, Luciani [Page 50]
INTERNET-DRAFT NBMA NHRP Expires June 1996
the the routed path to it lies entirely within the NBMA subnetwork,
the Next Hop Resolution Replies always return the NBMA address of the
destination station itself rather than the NBMA address of some
egress router. On the other hand, if the routed path exits the NBMA
subnetwork, NHRP will be unable to resolve the NBMA address of the
destination, but rather will return the address of the egress router.
For destinations outside the NBMA subnetwork, egress routers and
routers in the other subnetworks should exchange routing information
so that the optimal egress router may be found.
In addition to NHSs, an NBMA station could also be associated with
one or more regular routers that could act as "connectionless
servers" for the station. The station could then choose to resolve
the NBMA next hop or just send the packets to one of its
connectionless servers. The latter option may be desirable if
communication with the destination is short-lived and/or doesn't
require much network resources. The connectionless servers could, of
course, be physically integrated in the NHSs by augmenting them with
internetwork layer switching functionality.
References
[1] NBMA Address Resolution Protocol (NARP), Juha Heinanen and Ramesh
Govindan, draft-ietf-rolc-nbma-arp-00.txt.
[2] Address Resolution Protocol, David C. Plummer, RFC 826.
[3] Classical IP and ARP over ATM, Mark Laubach, RFC 1577.
[4] Transmission of IP datagrams over the SMDS service, J. Lawrence
and D. Piscitello, RFC 1209.
[5] Protocol Identification in the Network Layer, ISO/IEC TR
9577:1990.
[6] Assigned Numbers, J. Reynolds and J. Postel, RFC 1700.
[7] Multiprotocol Encapsulation over ATM Adaptation Layer 5, J. Heinanen,
RFC1483.
[8] Multiprotocol Interconnect on X.25 and ISDN in the Packet Mode,
A. Malis, D. Robinson, and R. Ullmann, RFC1356.
[9] Multiprotocol Interconnect over Frame Relay, T. Bradley, C. Brown, and
A. Malis, RFC1490.
Katz, Piscitello, Cole, Luciani [Page 51]
INTERNET-DRAFT NBMA NHRP Expires June 1996
Acknowledgments
We would like to thank Juha Heinenan of Telecom Finland and Ramesh
Govidan of ISI for their work on NBMA ARP and the original NHRP
draft, which served as the basis for this work. John Burnett of
Adaptive, Dennis Ferguson of ANS, Joel Halpern of Newbridge, Paul
Francis of NTT, Tony Li and Yakov Rekhter of cisco, and Grenville
Armitage of Bellcore should also be acknowledged for comments and
suggestions that improved this work substantially. We would also
like to thank the members of the Routing Over Large Clouds working
group of the IETF, whose review and discussion of this document have
been invaluable.
Authors' Addresses
Dave Katz David Piscitello
cisco Systems Core Competence
170 W. Tasman Dr. 1620 Tuckerstown Road
San Jose, CA 95134 USA Dresher, PA 19025 USA
Phone: +1 408 526 8284 Phone: +1 215 830 0692
Email: dkatz@cisco.com Email: dave@corecom.com
Bruce Cole James V. Luciani
cisco Systems Ascom Nexion
170 W. Tasman Dr. 289 Great Road
San Jose, CA 95134 USA Acton, MA 01720-4379 USA
Phone: +1 408 526 4000 Phone: +1 508 266 3450
Email: bcole@cisco.com Email: luciani@nexen.com
Katz, Piscitello, Cole, Luciani [Page 52]
