Routing over Large Clouds Working Group James V. Luciani
INTERNET-DRAFT (Bay Networks)
<draft-ietf-rolc-nhrp-08.txt> Dave Katz
(cisco Systems)
David Piscitello
(Core Competence, Inc.)
Bruce Cole
(cisco Systems)
Expires December 1996
NBMA Next Hop Resolution Protocol (NHRP)
Status of this Memo
This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as ``work in progress.''
To learn the current status of any Internet-Draft, please check the
``1id-abstracts.txt'' listing contained in the Internet-Drafts Shadow
Directories on ds.internic.net (US East Coast), nic.nordu.net
(Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific
Rim).
Abstract
This document describes the NBMA Next Hop Resolution Protocol (NHRP).
NHRP can be used by a source station (host or router) connected to a
Non-Broadcast, Multi-Access (NBMA) subnetwork to determine the
internetworking layer address and NBMA subnetwork addresses of the
"NBMA next hop" towards a destination station. If the destination is
connected to the NBMA subnetwork, then the NBMA next hop is the
destination station itself. Otherwise, the NBMA next hop is the
egress router from the NBMA subnetwork that is "nearest" to the
destination station. NHRP is intended for use in a multiprotocol
internetworking layer environment over NBMA subnetworks.
This document is intended to be a functional superset of the NBMA
Address Resolution Protocol (NARP) documented in [1].
Luciani, Katz, Piscitello, Cole [Page 1]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Operation of NHRP as a means of establishing a transit path across an
NBMA subnetwork between two routers will be addressed in a separate
document.
1. Introduction
The NBMA Next Hop Resolution Protocol (NHRP) allows a source station
(a host or router), wishing to communicate over a Non-Broadcast,
Multi-Access (NBMA) subnetwork, to determine the internetworking
layer addresses and NBMA addresses of suitable "NBMA next hops"
toward a destination station. A subnetwork can be non-broadcast
either because it technically doesn't support broadcasting (e.g., an
X.25 subnetwork) or because broadcasting is not feasible for one
reason or another (e.g., an SMDS multicast group or an extended
Ethernet would be too large). If the destination is connected to the
NBMA subnetwork, then the NBMA next hop is the destination station
itself. Otherwise, the NBMA next hop is the egress router from the
NBMA subnetwork that is "nearest" to the destination station.
One way to model an NBMA network is by using the notion of logically
independent IP subnets (LISs). LISs, as defined in [3] and [4], have
the following properties:
1) All members of a LIS have the same IP network/subnet number
and address mask.
2) All members within a LIS are directly connected to the same
NBMA subnetwork.
3) All members outside of the LIS are accessed via a router.
4) All members within the LIS access each other directly
(without routers)
Address resolution as described in [3] and [4] only resolves the next
hop address if the destination station is a member of the same LIS as
the source station; otherwise, the source station must forward
packets to a router that is a member of multiple LIS's. In multi-LIS
configurations, hop-by-hop address resolution may not be sufficient
to resolve the "NBMA next hop" toward the destination station, and IP
packets may have multiple IP hops through the NBMA subnetwork.
Another way to model NBMA is by using the notion of Local Address
Groups (LAGs) [10]. The essential difference between the LIS and the
LAG models is that while with the LIS model the outcome of the
"local/remote" forwarding decision is driven purely by addressing
information, with the LAG model the outcome of this decision is
Luciani, Katz, Piscitello, Cole [Page 2]
INTERNET-DRAFT NBMA NHRP Expires December 1996
decoupled from the addressing information and is coupled with the
Quality of Service and/or traffic characteristics. With the LAG
model any two entities on a common NBMA network could establish a
direct communication with each other, irrespective of the entities'
addresses.
Support for the LAG model assumes the existence of a mechanism that
allows any entity (i.e., host or router) connected to an NBMA network
to resolve an internetworking layer address to an NBMA address for
any other entity connected to the same NBMA network. This resolution
would take place regardless of the address assignments to these
entities. NHRP describes such a mechanism. For example, when the
internetworking layer address is of type IP, once the NBMA next hop
has been resolved, the source may either start sending IP packets to
the destination (in a connectionless NBMA subnetwork such as SMDS) or
may first establish a connection to the destination with the desired
bandwidth and QOS characteristics (in a connection-oriented NBMA
subnetwork such as ATM).
Use of NHRP may be sufficient for hosts doing address resolution when
those hosts are directly connected to an NBMA subnetwork, allowing
for straightforward implementations in NBMA stations. NHRP also has
the capability of determining the egress point from an NBMA
subnetwork when the destination is not directly connected to the NBMA
subnetwork and the identity of the egress router is not learned by
other methods (such as routing protocols). Optional extensions to
NHRP provide additional robustness and diagnosability.
Address resolution techniques such as those described in [3] and [4]
may be in use when NHRP is deployed. ARP servers and services over
NBMA subnetworks may be required to support hosts that are not
capable of dealing with any model for communication other than the
LIS model, and deployed hosts may not implement NHRP but may continue
to support ARP variants such as those described in [3] and [4]. NHRP
is intended to reduce or eliminate the extra router hops required by
the LIS model, and can be deployed in a non-interfering manner
alongside existing ARP services.
The operation of NHRP to establish transit paths across NBMA
subnetworks between two routers requires additional mechanisms to
avoid stable routing loops, and will be described in a separate
document.
Luciani, Katz, Piscitello, Cole [Page 3]
INTERNET-DRAFT NBMA NHRP Expires December 1996
2. Overview
2.1 Terminology
The term "network" is highly overloaded, and is especially confusing
in the context of NHRP. We use the following terms:
Internetwork layer--the media-independent layer (IP in the case of
TCP/IP networks).
Subnetwork layer--the media-dependent layer underlying the
internetwork layer, including the NBMA technology (ATM, X.25, SMDS,
etc.)
The term "server", unless explicitly stated to the contrary, refers
to an Next Hop Server (NHS). An NHS is an entity performing the
Next Hop Resolution Protocol service within the NBMA cloud. An NHS
is always tightly coupled with a routing entity (router, route
server or edge device) although the converse is not yet guaranteed
until ubiquitous deployment of this functionality occurs.
The term "client", unless explicitly stated to the contrary, refers
to an Next Hop Resolution Protocol client (NHC). An NHC is an
entity which initiates NHRP requests of various types in order to
obtain access to the NHRP service.
The term "station" generally refers to a host or router which
contains an NHRP entity. Occasionally, the term station will
describe a "user" of the NHRP client or service functionality; the
difference in usage is largely semantic.
2.2 Protocol Overview
In this section, we briefly describe how a source S (which
potentially can be either a router or a host) uses NHRP to determine
the "NBMA next hop" to destination D.
For administrative and policy reasons, a physical NBMA subnetwork may
be partitioned into several, disjoint "Logical NBMA subnetworks". A
Logical NBMA subnetwork is defined as a collection of hosts and
routers that share unfiltered subnetwork connectivity over an NBMA
subnetwork. "Unfiltered subnetwork connectivity" refers to the
absence of closed user groups, address screening or similar features
that may be used to prevent direct communication between stations
connected to the same NBMA subnetwork. (Hereafter, unless otherwise
specified, we use the term "NBMA subnetwork" to mean *logical* NBMA
subnetwork.)
Luciani, Katz, Piscitello, Cole [Page 4]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Placed within the NBMA subnetwork are one or more entities that
implement the NHRP protocol. Such stations which are capable of
answering Next Hop Resolution Requests are known as "Next Hop
Servers" (NHSs). Each NHS serves a set of destination hosts, which
may or may not be directly connected to the NBMA subnetwork. NHSs
cooperatively resolve the NBMA next hop within their logical NBMA
subnetwork. In addition to NHRP, NHSs may participate in protocols
used to disseminate routing information across (and beyond the
boundaries of) the NBMA subnetwork, and may support "classical" ARP
service as well.
An NHS maintains a "next-hop resolution" cache, which is a table of
address mappings (internetwork layer address to NBMA subnetwork layer
address). This table can be constructed from information gleaned
from NHRP Register packets (see Section 5.2.3 and 5.2.4), extracted
from Next Hop Resolution Requests/Replies that traverse the NHS as
they are forwarded, or through mechanisms outside the scope of this
document (examples of such mechanisms include ARP [2, 3, 4] and pre-
configured tables). Section 6.2 further describes cache management
issues.
A host or router that is not an NHRP server must be configured with
the identity of the NHS which serves it (see Configuration, Section
4).
[Note: for NBMA subnetworks that offer group or multicast addressing
features, it may be desirable to configure stations with a group
identity for NHSs, i.e., addressing information that would solicit a
response from "all NHSs". The means whereby a group of NHSs divide
responsibilities for next hop resolution are not described here.]
Whether or not a particular station within the NBMA subnetwork which
is making use of the NHRP protocol needs to be able to act as an NHS
is a local matter. For a station to avoid providing NHS
functionality, there must be one or more NHSs within the NBMA
subnetwork which are providing authoritative NBMA information on its
behalf. If NHRP is to be able to resolve the NBMA address for
stations that lack NHS functionality, these serving NHSs must exist
along all routed paths between Next Hop Resolution Requesters and the
station which cannot answer Next Hop Resolution Requests.
The protocol proceeds as follows. An event occurs triggering station
S to want to resolve the NBMA address of a path to D. This is most
likely to be when a data packet addressed to station D is to be
emitted from station S (either because station S is a host, or
station S is a transit router), but the address resolution could also
be triggered by other means (a routing protocol update packet, for
example). Station S first determines the next hop to station D
Luciani, Katz, Piscitello, Cole [Page 5]
INTERNET-DRAFT NBMA NHRP Expires December 1996
through normal routing processes (for a host, the next hop may simply
be the default router; for routers, this is the "next hop" to the
destination internetwork layer address). If the next hop is
reachable through one of its NBMA interfaces, S constructs an Next
Hop Resolution Request packet (see Section 5.2.1) containing station
D's internetwork layer address as the (target) destination address,
S's own internetwork layer address as the source address (Next Hop
Resolution Request initiator), and station S's NBMA addressing
information. Station S may also indicate that it prefers an
authoritative Next Hop Resolution Reply (i.e., station S only wishes
to receive a Next Hop Resolution Reply from the NHS-speaker that
maintains the NBMA-to-internetwork layer address mapping for this
destination). Station S emits the Next Hop Resolution Request packet
towards the destination.
If the Next Hop Resolution Request is triggered by a data packet,
station S may choose to dispose of the data packet while awaiting a
Next Hop Resolution Reply in one of the following ways:
(a) Drop the packet
(b) Retain the packet until the Next Hop Resolution Reply arrives
and a more optimal path is available
(c) Forward the packet along the routed path toward D
The choice of which of the above to perform is a local policy matter,
though option (c) is the recommended default, since it may allow data
to flow to the destination while the NBMA address is being resolved.
Note that an Next Hop Resolution Request for a given destination MUST
NOT be triggered on every packet, though periodically retrying a Next
Hop Resolution Request is permitted.
When the NHS receives an Next Hop Resolution Request, a check is made
to see if it "serves" station D, i.e., the NHS checks to see if there
is a "next hop" entry for D in its next-hop resolution cache. If the
NHS does not serve D, the NHS forwards the Next Hop Resolution
Request to another NHS. (Mechanisms for determining how to forward
the Next Hop Resolution Request are discussed in Section 3,
Deployment.) Note that NHSs must be next hops to one another in order
for forwarding of NHRP packets to be possible.
If this NHS serves D, the NHS resolves station D's NBMA address, and
generates a positive Next Hop Resolution Reply (denoted by a 0 Code
in the reply) on D's behalf. (Next Hop Resolution Replies in this
scenario are always marked as "authoritative".) The Next Hop
Resolution Reply packet contains the next hop internetwork layer
address and the NBMA address for station D and is sent back to S.
(Note that if station D is not on the NBMA subnetwork, the next hop
internetwork layer address will be that of the egress router through
Luciani, Katz, Piscitello, Cole [Page 6]
INTERNET-DRAFT NBMA NHRP Expires December 1996
which packets for station D are forwarded.)
An NHS receiving a Next Hop Resolution Reply may cache the NBMA next
hop information contained therein. To a subsequent Next Hop
Resolution Request, this NHS may respond with the cached, non-
authoritative, NBMA next hop information or with cached negative
information, if the NHS is allowed to do so, see section 5.2.2 and
6.2. Non-authoritative Next Hop Resolution Replies are distinguished
from authoritative Next Hop Resolution Replies so that if a
communication attempt based on non-authoritative information fails, a
source station can choose to send an authoritative Next Hop
Resolution Request. NHSs MUST NOT respond to authoritative Next Hop
Resolution Requests with cached information.
[Note: An Next Hop Resolution Reply can be returned directly to the
Next Hop Resolution Request initiator, i.e., without traversing the
list of NHSs that forwarded the Next Hop Resolution Request, if all
of the following criteria are satisfied:
(a) Direct communication is available via datagram transfer
(e.g., SMDS) or the NHS has an existing virtual circuit
connection to the Next Hop Resolution Request initiator or is
permitted to open one.
(b) The Next Hop Resolution Request initiator has not included the
NHRP Reverse NHS record Extension (see Section 5.3.5).
(c) The authentication policy in force permits direct
communication between the NHS and the Next Hop Resolution
Request initiator.
The purpose of allowing an NHS to send a Next Hop Resolution Reply
directly is to reduce response time. A consequence of allowing a
direct Next Hop Resolution Reply is that NHSs that would under
normal circumstances be traversed by the Next Hop Resolution Reply
would not cache next hop information contained therein.]
The process of forwarding the Next Hop Resolution Request is repeated
until the Next Hop Resolution Request is satisfied, or an error
occurs (e.g., no NHS in the NBMA subnetwork can resolve the Next Hop
Resolution Request.) If the determination is made that station D's
next hop cannot be resolved, a negative Next Hop Resolution Reply
(NAK) is returned. This occurs when (a) no next-hop resolution
information is available for station D from any NHS, or (b) an NHS is
unable to forward the Next Hop Resolution Request (e.g., connectivity
is lost).
NHRP Registration Requests, NHRP Purge Requests, NHRP Purge Replies,
and NHRP Error Indications follow the routed path from sender to
receiver in the same fashion that Next Hop Resolution Requests and
Luciani, Katz, Piscitello, Cole [Page 7]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Next Hop Resolution Replies do. That is, "requests" and
"indications" follow the routed path from Source Protocol Address
(which is the address of the station initiating the communication) to
the Destination Protocol Address. "Replies", on the other hand,
follow the routed path from the Destination Protocol Address back to
the Source Protocol Address with the exceptions mentioned above where
a direct VC may be created. In the case of a NHRP Registration
Reply, the packet is always returned via a direct VC (see Section
5.2.4).
NHRP Requests and NHRP Replies MUST NOT cross the borders of a
logical NBMA subnetwork (an explicit NBMA subnetwork identifier may
be included as an extension in the Next Hop Resolution Request, see
section 5.3.2). Thus, the internetwork layer traffic out of and into
a logical NBMA subnetwork always traverses an internetwork layer
router at its border. Internetwork layer filtering can then be
implemented at these border routers.
NHRP optionally provides a mechanism to send a Next Hop Resolution
Reply which contains aggregated NBMA next hop information. Suppose
that router X is the NBMA next hop from station S to station D.
Suppose further that X is an egress router for all stations sharing
an internetwork layer address prefix with station D. When an Next
Hop Resolution Reply is generated in response to a Next Hop
Resolution Request, the responder may augment the internetwork layer
address of station D with a prefix length (see Section 5.2.0.1). A
subsequent (non-authoritative) Next Hop Resolution Request for some
destination that shares an internetwork layer address prefix (for the
number of bits specified in the prefix length) with D may be
satisfied with this cached information. See section 6.2 regarding
caching issues.
To dynamically detect subnetwork-layer filtering in NBMA subnetworks
(e.g., X.25 closed user group facility, or SMDS address screens), to
trace the routed path that an NHRP packet takes, or to provide loop
detection and diagnostic capabilities, a "Route Record" may be
included in NHRP packets (see Sections 5.3.4 and 5.3.5). The Route
Record extensions contain the internetwork (and subnetwork layer)
addresses of all intermediate NHSs between source and destination (in
the forward direction) and between destination and source (in the
reverse direction). When a source station is unable to communicate
with the responder (e.g., an attempt to open an SVC fails), it may
attempt to do so successively with other subnetwork layer addresses
in the Route Record until it succeeds (if authentication policy
permits such action). This approach can find a suitable egress point
in the presence of subnetwork-layer filtering (which may be
source/destination sensitive, for instance, without necessarily
creating separate logical NBMA subnetworks) or subnetwork-layer
Luciani, Katz, Piscitello, Cole [Page 8]
INTERNET-DRAFT NBMA NHRP Expires December 1996
congestion (especially in connection-oriented media).
3. Deployment
Next Hop Resolution Requests traverse one or more hops within an NBMA
subnetwork before reaching the station that is expected to generate a
response. Each station, including the source station, chooses a
neighboring NHS to which it will forward the Next Hop Resolution
Request. The NHS selection procedure typically involves applying a
destination protocol layer address to the protocol layer routing
table which causes a routing decision to be returned. This routing
decision is then used to forward the Next Hop Resolution Request to
the downstream NHS. The destination protocol layer address previously
mentioned is carried within the Next Hop Resolution Request packet.
Note that even though a protocol layer address was used to acquire a
routing decision, NHRP packets are not encapsulated within a protocol
layer header but rather are carried at the NBMA layer using the
encapsulation described in Section 5.
Each NHS/router examines the Next Hop Resolution Request packet on
its way toward the destination. Each NHS which the NHRP packet
traverses on the way to the packet's destination might modify the
packet (e.g., updating the Forward Record extension). Ignoring error
situations, the Next Hop Resolution Request eventually arrives at a
station that is to generate an Next Hop Resolution Reply. This
responding station "serves" the destination. The responding station
generates a Next Hop Resolution Reply using the source protocol
address from within the NHRP packet to determine where the Next Hop
Resolution Reply should be sent.
Rather than use routing to determine the next hop for an NHRP packet,
an NHS may use static configuration information (or other applicable
means) in order to determine to which neighboring NHSs to forward the
Next Hop Resolution Request packet. The use of static configuration
information for this purpose is beyond the scope of this document.
In order to forward NHRP packets to a neighboring NHS, NHRP clients
must nominally be configured with the NBMA address of at least one
NHS. In practice, a client's default router should also be its NHS
in that way a client may be able to know the NBMA address of its NHS
from the configuration which was already required for the client to
be able to communicate.
The NHS serving a particular destination must lie along the routed
path to that destination. In practice, this means that all egress
routers must double as NHSs serving the destinations beyond them, and
that hosts on the NBMA subnetwork are served by routers that double
Luciani, Katz, Piscitello, Cole [Page 9]
INTERNET-DRAFT NBMA NHRP Expires December 1996
as NHSs. Also, this implies that forwarding of NHRP packets within
an NBMA subnetwork requires a contiguous deployment of NHRP capable
routers. During migration to NHRP, it cannot be expected that all
routers within the NBMA subnetwork are NHRP capable. Thus, NHRP
traffic which would otherwise need to be forwarded through such
routers can be expected to be dropped due to the NHRP packet not
being recognized. In this case, NHRP will be unable to establish any
transit paths whose discovery requires the traversal of the non-NHRP
speaking routers. If the client has tried and failed to acquire a
cut through path then the client should use the network layer routed
path as a default.
If a subnetwork offers a link layer group addressing or multicast
feature, the client (station) may be configured with a group address
assigned to the group of next-hop servers. The client might then
submit Next Hop Resolution Requests to the group address, eliciting a
response from one or more NHSs, depending on the response strategy
selected. Note that the constraints described in Section 2 regarding
directly sending Next Hop Resolution Reply may apply.
4. Configuration
Clients
To participate in NHRP, a client connected to an NBMA subnetwork
should be configured with the NBMA address(es) of its NHS(s)
(alternatively, it should be configured with a means of acquiring
them, i.e., the group address that members of a NHS group use for
the purpose of address or next-hop resolution.) The NHS(s) will
likely also represent the client's default or peer routers, so
their NBMA addresses may be obtained from the client's existing
configuration. If the client is attached to several subnetworks
(including logical NBMA subnetworks), the client should also be
configured to receive routing information from its NHS(s) and peer
routers so that it can determine which internetwork layer networks
are reachable through which subnetworks.
Next Hop Servers
An NHS is configured with knowledge of its own internetwork layer
and NBMA addresses and a logical NBMA subnetwork identifier (see
Section 5.3.2). An NHS MAY also be configured with a set of
internetwork layer address prefixes that correspond to the
internetwork layer addresses of the stations it serves. If a served
client is attached to several subnetworks, the NHS may also need to
be configured to advertise routing information to such client.
Luciani, Katz, Piscitello, Cole [Page 10]
INTERNET-DRAFT NBMA NHRP Expires December 1996
If an NHS acts as an egress router for stations connected to other
subnetworks than the NBMA subnetwork, the NHS must, in addition to
the above, be configured to exchange routing information between
the NBMA subnetwork and these other subnetworks.
In all cases, routing information is exchanged using conventional
intra-domain and/or inter-domain routing protocols.
The NBMA addresses of the stations served by the NHS may be learned
via NHRP Register packets or manual configuration.
5. NHRP Packet Formats
This section describes the format of NHRP packets. In the following,
unless otherwise stated explicitly, the unqualified term "request"
refers generically to any of the NHRP packet types which are
"requests". Further, unless otherwise stated explicitly, the
unqualified term "reply" refers generically to any of the NHRP packet
types which are "replies".
An NHRP packet consists of a Fixed Part, a Mandatory Part, and an
Extensions Part. The Fixed Part is common to all NHRP packet types.
The Mandatory Part MUST be present, but varies depending on packet
type. The Extensions Part also varies depending on packet type, and
need not be present.
The length of the Fixed Part is fixed at 20 octets. The length of
the Mandatory Part is determined by the contents of the extensions
offset field (ar$extoff). If ar$extoff=0x0 then the mandatory part
length is equal to total packet length (ar$pktsz) minus 20 otherwise
the mandatory part length is equal to ar$extoff minus 20. The length
of the Extensions Part is implied by ar$pktsz minus ar$extoff. NHSs
may increase the size of an NHRP packet as a result of extension
processing, but not beyond the offered maximum SDU size of the NBMA
network.
NHRP packets are encapsulated using the native formats used on the
particular NBMA network over which NHRP is carried. For example,
SMDS networks always use LLC/SNAP encapsulation at the NBMA layer,
and an NHRP packet is preceded by the following LLC/SNAP
encapsulation:
[0xAA-AA-03] [0x00-00-5E] [0x00-03]
The first three octets are LLC, indicating that SNAP follows. The
SNAP OUI portion is the IANA's OUI, and the SNAP PID portion
identifies NHRP (see [4]).
Luciani, Katz, Piscitello, Cole [Page 11]
INTERNET-DRAFT NBMA NHRP Expires December 1996
ATM uses either LLC/SNAP encapsulation of each packet (including
NHRP), or uses no encapsulation on VCs dedicated to a single protocol
(see [7]). Frame Relay and X.25 both use NLPID/SNAP encapsulation or
identification of NHRP, using a NLPID of 0x0080 and the same SNAP
contents as above (see [8], [9]).
Fields marked "unused" MUST be set to zero on transmission, and
ignored on receipt.
Most packet types (ar$op.type) have both internetwork layer
protocol-independent fields and protocol-specific fields. The
protocol type/snap fields (ar$pro.type/snap) qualify the format of
the protocol-specific fields.
5.1 NHRP Fixed Header
The Fixed Part of the NHRP packet contains those elements of the NHRP
packet which are always present and do not vary in size with the type
of packet.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$afn | ar$pro.type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$pro.snap |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$pro.snap | ar$hopcnt | ar$pktsz |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$chksum | ar$extoff |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ar$op.version | ar$op.type | ar$shtl | ar$sstl |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ar$afn
Defines the type of "link layer" addresses being carried. This
number is taken from the 'address family number' list specified in
[6]. This field has implications to the coding of ar$shtl and
ar$sstl as described below.
ar$pro.type
field is a 16 bit unsigned integer representing the following
number space:
0x0000 to 0x00FF Protocols defined by the equivalent NLPIDs.
0x0100 to 0x03FF Reserved for future use by the IETF.
Luciani, Katz, Piscitello, Cole [Page 12]
INTERNET-DRAFT NBMA NHRP Expires December 1996
0x0400 to 0x04FF Allocated for use by the ATM Forum.
0x0500 to 0x05FF Experimental/Local use.
0x0600 to 0xFFFF Protocols defined by the equivalent Ethertypes.
(based on the observations that valid Ethertypes are never smaller
than 0x600, and NLPIDs never larger than 0xFF.)
ar$pro.snap
When ar$pro.type has a value of 0x0080, a SNAP encoded extension is
being used to encode the protocol type. This snap extension is
placed in the ar$pro.snap field. This is termed the 'long form'
protocol ID. If ar$pro != 0x0080 then the ar$pro.snap field MUST be
zero on transmit and ignored on receive. The ar$pro.type field
itself identifies the protocol being referred to. This is termed
the 'short form' protocol ID.
In all cases, where a protocol has an assigned number in the
ar$pro.type space (excluding 0x0080) the short form MUST be used
when transmitting NHRP messages. Additionally, where a protocol has
valid short and long forms of identification, receivers MAY choose
to recognize the long form.
ar$hopcnt
The Hop count indicates the maximum number of NHSs that an NHRP
packet is allowed to traverse before being discarded.
ar$pktsz
The total length of the NHRP packet, in octets (excluding link
layer encapsulation).
ar$chksum
The standard IP checksum over the entire NHRP packet (starting with
the fixed header). If only the hop count field is changed, the
checksum is adjusted without full recomputation. The checksum is
completely recomputed when other header fields are changed.
ar$extoff
This field identifies the existence and location of NHRP
extensions. If this field is 0 then no extensions exist otherwise
this field represents the offset from the beginning of the NHRP
packet (i.e., starting from the ar$afn field) of the first
extension.
ar$op.version
This field is set to 0x01 for NHRP version 1.
ar$op.type
This is the NHRP packet type: NHRP Next Hop Resolution Request(1),
Luciani, Katz, Piscitello, Cole [Page 13]
INTERNET-DRAFT NBMA NHRP Expires December 1996
NHRP Next Hop Resolution Reply(2), NHRP Registration Request(3),
NHRP Registration Reply(4), NHRP Purge Request(5), NHRP Purge
Reply(6), or NHRP Error Indication(7). Use of NHRP packet Types in
the range 128 to 255 are reserved for research or use in other
protocol development and will be administered by IANA.
ar$shtl
Type & length of source NBMA address interpreted in the context of
the 'address family number'[6] indicated by ar$afn (e.g.,
ar$afn=0x0003 for NSAP, ar$afn=8 for E.164). When ar$afn=0x000F
(E.164 address plus NSAP subaddress) then both ar$shtl and ar$sstl
must be coded appropriately (see below).
ar$sstl
Type & length of source NBMA subaddress interpreted in the context
of the 'address family number'[6] indicated by ar$afn (e.g.,
ar$afn=0x000F for NSAP). When an NBMA technology has no concept of
a subaddress, the subaddress length is always coded ar$sstl = 0 and
no storage is allocated for the subaddress in the appropriate
mandatory part.
ar$shtl, ar$sstl, subnetwork layer addresses, and subnetwork layer
subaddresses fields are coded as follows:
7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+
|0|x| length |
+-+-+-+-+-+-+-+-+
The most significant bit is reserved and MUST be set to zero. The
second most significant bit (x) is a flag indicating whether the
address being referred to is in:
- NSAP format (x = 0).
- Native E.164 format (x = 1).
For NBMA technologies that use neither NSAP nor E.164 format
addresses, x = 0 SHALL be used to indicate the native form for the
particular NBMA technology.
In the case where the NBMA is ATM, if a subaddress is to be included
then ar$afn MUST be set to 0x000F which means that if a subaddress
exists then it is of type NSAP.
The bottom 6 bits is an unsigned integer value indicating the length
of the associated NBMA address in octets. If this value is zero the
flag x is ignored.
Luciani, Katz, Piscitello, Cole [Page 14]
INTERNET-DRAFT NBMA NHRP Expires December 1996
5.2.0 Mandatory Part
The Mandatory Part of the NHRP packet contains the operation specific
information (e.g., Next Hop Resolution Request/Reply, etc.) and
variable length data which is pertinent to the packet type.
5.2.0.1 Mandatory Part Format
Sections 5.2.1 through 5.2.6 have a very similar mandatory part.
This mandatory part includes a common header and zero or more Client
Information Entries (CIEs). Section 5.2.7 has a different format
which is specified in that section.
The common header looks like the following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len | Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
And the CIEs have the following format:
Luciani, Katz, Piscitello, Cole [Page 15]
INTERNET-DRAFT NBMA NHRP Expires December 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code | Prefix Length | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Maximum Transmission Unit | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cli Addr T/L | Cli SAddr T/L | Cli Proto Len | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Client NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Client NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Client Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
.....................
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code | Prefix Length | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Maximum Transmission Unit | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cli Addr T/L | Cli SAddr T/L | Cli Proto Len | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Client NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Client NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Client Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The meanings of the fields are as follows:
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Flags
These flags are specific to the given message type and they are
explained in each section.
Request ID
A value which, when coupled with the address of the source,
provides a unique identifier for the information contained in a
"request" packet. This value is copied directly from an "request"
Luciani, Katz, Piscitello, Cole [Page 16]
INTERNET-DRAFT NBMA NHRP Expires December 1996
packet into the associated "reply". When a sender of a "request"
receives "reply", it will compare the Request ID and source address
information in the received "reply" against that found in its
outstanding "request" list. When a match is found then the
"request" is considered to be acknowledged.
The value is taken from a 32 bit counter that is incremented each
time a new "request" is transmitted. The same value MUST be used
when resending a "request", i.e., when a "reply" has not been
received for a "request" and a retry is sent after an appropriate
interval.
The NBMA address/subaddress form specified below allows combined
E.164/NSAPA form of NBMA addressing. For NBMA technologies without a
subaddress concept, the subaddress field is always ZERO length and
ar$sstl = 0.
Source NBMA Address
The Source NBMA address field is the address of the source station
which is sending the "request". If the field's length as specified
in ar$shtl is 0 then no storage is allocated for this address at
all.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the source
station which is sending the "request". If the field's length as
specified in ar$sstl is 0 then no storage is allocated for this
address at all.
Source Protocol Address
This is the protocol address of the station which is sending the
"request". This is also the protocol address of the station toward
which a "reply" packet is sent.
Destination Protocol Address
This is the protocol address of the station toward which a
"request" packet is sent.
Code
This field is message specific. See the relevant message sections
below. In general, this field is a NAK code; i.e., when the field
is 0 in a reply then the packet is acknowledging a request and if
it contains any other value the packet contains a negative
acknowledgment.
Prefix Length
This field is message specific. See the relevant message sections
below. In general, however, this fields is used to indicate that
Luciani, Katz, Piscitello, Cole [Page 17]
INTERNET-DRAFT NBMA NHRP Expires December 1996
the information carried in an NHRP the message pertains to an
equivalence class of internetwork layer addresses rather than just
a single internetwork layer address specified. All internetwork
layer addresses that match the first "Prefix Length" bit positions
for the specific internetwork layer address are included in the
equivalence class.
Maximum Transmission Unit
This field gives the maximum transmission unit for the relevant
client station. If this value is 0 then either the default MTU is
used or the MTU negotiated via signaling is used if such
negotiation is possible for the given NBMA.
Holding Time
The Holding Time field specifies the number of seconds for which
the Next Hop NBMA information specified in the CIE is considered to
be valid. Cached information SHALL be discarded when the holding
time expires. This field must be set to 0 on a NAK.
Cli Addr T/L
Type & length of next hop NBMA address specified in the CIE. This
field is interpreted in the context of the 'address family
number'[6] indicated by ar$afn (e.g., ar$afn=0x0003 for ATM).
Cli SAddr T/L
Type & length of next hop NBMA subaddress specified in the CIE.
This field is interpreted in the context of the 'address family
number'[6] indicated by ar$afn (e.g., ar$afn=0x0015 for ATM makes
the address an E.164 and the subaddress an ATM Forum NSAP address).
When an NBMA technology has no concept of a subaddress, the
subaddress is always null with a length of 0. When the address
length is specified as 0 no storage is allocated for the address.
Cli Proto Len
This field holds the length in octets of the Client Protocol
Address specified in the CIE.
Preference
This field specifies the preference for use of the specific CIE
relative to other CIEs. Higher values indicate higher preference.
Action taken when multiple CIEs have equal or highest preference
value is a local matter.
Client NBMA Address
This is the client's NBMA address.
Client NBMA SubAddress
This is the client's NBMA subaddress.
Luciani, Katz, Piscitello, Cole [Page 18]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Client Protocol Address
This is the client's internetworking layer address specified.
Note that an NHS SHOULD NOT cache source information which is in an
NHRP message because this information could be inappropriately used
to set up a cut-through without doing proper filtering along a routed
path. Further, in the case where a distributed router exists in the
network, incorrect or incomplete information may be included in the
source information.
5.2.1 NHRP Next Hop Resolution Request
The NHRP Next Hop Resolution Request packet has a Type code of 1. Its
mandatory part is coded as described in Section 5.2.0.1 and the message
specific meanings of the fields are as follows:
Flags - The flags field is coded as follows:
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Q|A|B|U| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Q
Set if the station sending the Next Hop Resolution Request is a
router; clear if the it is a host.
A
This bit is set in a Next Hop Resolution Request if only
authoritative next hop information is desrired and is clear
otherwise. See the NHRP Next Hop Resolution Reply section below
for further details on the "A" bit and its usage.
B
Unused (clear on transmit)
U
This is the Uniqueness bit. This bit aids in duplicate address
detection. When this bit is set in an NHRP Resolution Request
and one or more entries exist in the NHS cache which meet the
requirements of the NHRP Resolution Request then only the CIE in
the NHS's cache with this bit set will be returned. Note that
even if this bit was set at registration time, there may still be
multiple CIEs that might fulfill the NHRP Resolution Request
because an entire subnet can be registered through use of the
Prefix Length in the CIE and the address of interest might be
within such a subnet. If the "uniqueness" bit is set and the
Luciani, Katz, Piscitello, Cole [Page 19]
INTERNET-DRAFT NBMA NHRP Expires December 1996
responding NHS has one or more cache entries which match the
request but no such cache entry has the "uniqueness" bit set,
then the NHRP Resolution Reply returns with a NAK code of "13 -
Binding Exists But Is Not Unique" and no CIE is included. If a
client wishes to receive non- unique Next Hop Entries, then
the client must have the "uniqueness" bit set to zero in its NHRP
Resolution Request. Note that when this bit is set in an NHRP
Registration Request, only a single CIE may be specified in the
NHRP Registration Request and that CIE must have the Prefix
Length field set to 0xFF.
Zero or one CIEs (see Section 5.2.0.1) may be specified in an NHRP
Next Hop Resolution Request. If one is specified then that entry
carries the pertinent information for the client sourcing the NHRP
Next Hop Resolution Request. Usage of the CIE in the NHRP Next Hop
Resolution Request is described below:
Prefix Length
If a CIE is specified in the NHRP Next Hop Resolution Request
then the Prefix Length field may be used to qualify the widest
acceptable prefix which may be used to satisfy the NHRP Next Hop
Resolution Request. In the case of NHRP Next Hop Resolution
Request/Reply, the Prefix Length specifies the equivalence class
of addresses which match the first "Prefix Length" bit positions
of the Destination Protocol Address. If this field is set to
0x00 then this field MUST be ignored. If the "U" bit is set in
the common header then this field MUST be set to 0xFF.
Maximum Transmission Unit
This field gives the maximum transmission unit for the source
station. A possible use of this field in the Next Hop Resolution
Request packet is for the Next Hop Resolution Requester to ask
for a target MTU. In lieu of that usage, the CIE must be omitted.
All other fields in the CIE MUST be ignored and SHOULD be set to 0.
5.2.2 NHRP Next Hop Resolution Reply
The NHRP Next Hop Resolution Reply packet has a Type code of 2. CIEs
correspond to Next Hop Entries in an NHS's cache which match the
criteria in the NHRP Next Hop Resolution Request. Its mandatory part is
coded as described in Section 5.2.0.1. The message specific meanings of
the fields are as follows:
Flags - The flags field is coded as follows:
Luciani, Katz, Piscitello, Cole [Page 20]
INTERNET-DRAFT NBMA NHRP Expires December 1996
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Q|A|B|U| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Q
Copied from the Next Hop Resolution Request. Set if the Next Hop
Resolution Requester is a router; clear if it is a host.
A
Set if the next hop CIE in the Next Hop Resolution Reply is
authoritative; clear if the Next Hop Resolution Reply is non-
authoritative.
When an NHS receives a Next Hop Resolution Request for
authoritative information for which it is the authoritative
source, it MUST respond with a Next Hop Resolution Reply
containing all and only those next hop CIEs which are contained
in the NHS's cache which both match the criteria of the Next Hop
Resolution Request and are authoritative cache entries. An NHS
is an authoritative source for a Next Hop Resolution Request if
the information in the NHS's cache matches the Next Hop
Resolution Request criteria and that information was obtained
through a NHRP Registration Request or through synchronization
with an NHS which obtained this information through a NHRP
Registration Request. An authoritative cache entry is one which
is obtained through a NHRP Registration Request or through
synchronization with an NHS which obtained this information
through a NHRP Registration Request.
An NHS obtains non-authoriative CIEs through promiscuous
listening to NHRP packets other than NHRP Registrations which are
directed at it. A Next Hop Resolution Request which indicates a
request for non-authoritative information should cause a Next Hop
Resolution Reply which contains all entries in the replying NHS's
cache (i.e., both authoritative and non-authoritative) which
match the criteria specified in the request.
B
Set if the association between the destination and the next hop
information is guaranteed to be stable for the lifetime of the
information (the holding time). This is the case if the Next Hop
protocol address identifies the destination (though it may be
different in value than the Destination address if the
destination system has multiple addresses) or if the destination
is not connected directly to the NBMA subnetwork but the egress
router to that destination is guaranteed to be stable (such as
Luciani, Katz, Piscitello, Cole [Page 21]
INTERNET-DRAFT NBMA NHRP Expires December 1996
when the destination is immediately adjacent to the egress router
through a non-NBMA interface). This information affects caching
strategies (see section 6.2).
U
This is the Uniqueness bit. See the NHRP Resolution Request
section above for details. When this bit is set only, only one
CIE is included since only one unique binding should exist in an
NHS's cache.
One or more CIEs are specified in the NHRP Next Hop Resolution Reply.
Each CIE contains NHRP next hop information which the responding NHS
has cached and which matches the parameters specified in the NHRP
Next Hop Resolution Request. If no match is found by the NHS issuing
the NHRP Next Hop Resolution Reply then a single CIE is enclosed with
the a CIE Code set appropriately (see below) and all other fields
MUST be ignored and SHOULD be set to 0. In order to facilitate the
use of NHRP by minimal client implementations, the first CIE MUST
contain the next hop with the highest preference value so that such
an implementation need parse only a single CIE.
Code
If this field is set to zero then this packet contains a
positively acknowledged NHRP Resolution Reply. If this field
contains any other value then this message contains an NHRP
Resolution Reply NAK which means that an appropriate
internetworking layer to NBMA address binding was not available
in the responding NHS's cache. If NHRP Resolution Reply contains
a Client Information Entry with a NAK Code other than 0 then it
MUST NOT contain any other CIE. Currently defined NAK Codes are
as follows:
12 - No Internetworking Layer Address to NBMA Address Binding
Exists
This code states that there were absolutely no internetworking
layer address to NBMA address bindings found in the responding
NHS's cache.
13 - Binding Exists But Is Not Unique
This code states that there were one or more internetworking
layer address to NBMA address bindings found in the responding
NHS's cache, however none of them had the uniqueness bit set.
Prefix Length
In the case of NHRP Next Hop Resolution Reply, the Prefix Length
specifies the equivalence class of addresses which match the
Luciani, Katz, Piscitello, Cole [Page 22]
INTERNET-DRAFT NBMA NHRP Expires December 1996
first "Prefix Length" bit positions of the Destination Protocol
Address.
Holding Time
The Holding Time specified in a CIE of an NHRP Resolution Reply
is the amount of time remaining before the expiration of the
client information which is cached at the replying NHS. It is
not the value which was registered by the client.
The remainder of the fields for the CIE for each next hop are
filled out as they were defined when the next hop was registered
with the responding NHS (or one of the responding NHS's
synchronized servers) via the NHRP Registration Request.
Load-splitting may be performed when more than one Client Information
Entry is returned to a requester when equal preference values are
specified. Also, the alternative addresses may be used in case of
connectivity failure in the NBMA subnetwork (such as a failed call
attempt in connection-oriented NBMA subnetworks).
Any extensions present in the Next Hop Resolution Request packet MUST
be present in the NHRP Next Hop Resolution Reply even if the
extension is non-Compulsory.
If an unsolicited NHRP Next Hop Resolution Reply packet is received,
an Error Indication of type Invalid Next Hop Resolution Reply
Received SHOULD be sent in response.
5.2.3 NHRP Registration Request
The NHRP Registration Request is sent from a station to an NHS to
notify the NHS of the station's NBMA information. It has a Type code
of 3. Each CIE corresponds to Next Hop information which is to be
cached at an NHS. The mandatory part of an NHRP Registration Request
is coded as described in Section 5.2.0.1. The message specific
meanings of the fields are as follows:
Flags - The flags field is coded as follows:
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|U| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
U
This is the Uniqueness bit. When set in an NHRP Registration
Request, this bit indicates that the registration of the protocol
Luciani, Katz, Piscitello, Cole [Page 23]
INTERNET-DRAFT NBMA NHRP Expires December 1996
address is unique within the confines of the set of synchronized
NHSs. This "uniqueness" qualifier MUST be stored in the NHS/NHC
cache. Any attempt to register a binding between the protocol
address and an NBMA address when this bit is set MUST be rejected
with a Code of "14 - Unique Internetworking Layer Address Already
Registered" if the replying NHS already has a cache entry for the
protocol address and the cache entry has the "uniqueness" bit
set. A registration of a CIE's information is rejected when the
CIE is returned with the Code field set to anything other than
0x00. See the description of the uniqueness bit in NHRP
Resolution Request section above for further details. When this
bit is set only, only one CIE MAY be included in the NHRP
Registration Request.
Request ID
The request ID has the same meaning as described in Section
5.2.0.1. However, the request ID for NHRP Registrations which is
maintained at each client MUST be kept in non-volatile memory so
that when a client crashes and reregisters there will be no
inconsistency in the NHS's database. In order to reduce the
overhead associated with updating non-volatile memory, the actual
updating need not be done with every increment of the Request ID
but could be done, for example, every 50 or 100 increments. In
this scenario, when a client crashes and reregisters it knows to
add 100 to the value of the Request ID in the non-volatile memory
before using the Request ID for subsequent registrations.
One or more CIEs are specified in the NHRP Registration Request.
Each CIE contains next hop information which a client is attempting
to register with its servers. Generally, all fields in CIEs enclosed
in NHRP Registration Requests are coded as described in Section
5.2.0.1. However, if a station is only registering itself with the
NHRP Registration Request then it MAY code the Cli Addr T/L, Cli
SAddr T/L, and Cli Proto Len as zero which signifies that the client
address information is to be taken from the source information in the
common header (see Section 5.2.0.1). Below, further clarification is
given for some fields in a CIE in the context of a NHRP Registration
Request.
Code
This field is set to 0x00 in NHRP Registration Requests.
Prefix Length
This field may be used in a NHRP Registration Request to register
equivalence information for the Client Protocol Address specified
Luciani, Katz, Piscitello, Cole [Page 24]
INTERNET-DRAFT NBMA NHRP Expires December 1996
in the CIE of an NHRP Registration Request In the case of NHRP
Registration Request, the Prefix Length specifies the equivalence
class of addresses which match the first "Prefix Length" bit
positions of the Client Protocol Address. If this field is set
to 0x00 then this field MUST be ignored and no equivalence
information is assumed (i.e., only Client Protocol Address is
bound to the NBMA information). If the "U" bit is set in the
common header then this field MUST be set to 0xFF.
This packet is used to register a station's NHRP information with its
NHSs, as configured or known through conventional routing means.
NHSs may also be configured with the identities of stations that they
serve. If an NHS receives an NHRP Registration Request packet which
has the Destination Protocol Address field set to an address other
than the NHS's own protocol address then the NHS MUST forward the
packet along the routed path toward the Destination Protocol Address.
It is possible that a misconfigured station will attempt to register
with the wrong NHS (i.e., one that cannot serve it due to policy
constraints or routing state). If this is the case, the NHS MUST
reply with a NAK-ed Registration Reply of type Can't Serve This
Address.
If an NHS cannot serve a station due to a lack of resources, the NHS
MUST reply with a NAK-ed Registration Reply of type Registration
Overflow.
In order to keep the registration entry from being discarded, the
station MUST re-send the NHRP Registration Request packet often
enough to refresh the registration, even in the face of occasional
packet loss. It is recommended that the NHRP Registration Request
packet be sent at an interval equal to one-third of the Holding Time
specified therein.
5.2.4 NHRP Registration Reply
The NHRP Registration Reply is sent by an NHS to a client in response
to that client's NHRP Registration Request. If the Code field of a
CIE in the NHRP Registration Reply has anything other than 0 zero in
it then the NHRP Registration Reply is a NAK otherwise the reply is
an ACK. The NHRP Registration Reply has a Type code of 4.
An NHRP Registration Reply is formed from an NHRP Registration
Request by changing the type code to 4, updating the CIE Code field,
and filling in the appropriate extensions if they exist. The message
specific meanings of the fields are as follows:
Attempts to register the information in the CIEs of an NHRP
Luciani, Katz, Piscitello, Cole [Page 25]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Registration Request may fail for various reasons. If this is the
case then each failed attempt to register the information in a CIE of
an NHRP Registration Request is logged in the associated NHRP
Registration Reply by setting the CIE Code field to the appropriate
error code as shown below:
CIE Code
0 - Successful Registration
The information in the CIE was sucessfully registered with the
NHS.
4 - Can't Serve This Address
An NHS may refuse an NHRP Registration Request attempt for
administrative reasons (due to policy constraints or routing
state). If so, the NHS MUST send an NHRP Registration Reply
which contains a NAK code of 4.
5 - Registration Overflow
If an NHS cannot serve a station due to a lack of resources,
the NHS MUST reply with a NAKed NHRP Registration Reply which
contains a NAK code of 5.
14 - Unique Internetworking Layer Address Already Registered
If a client tries to register a protocol address to NBMA
address binding with the uniqueness bit on and the protocol
address already exists in the NHS's cache then if that cache
entry also has the uniqueness bit on then this NAK Code is
returned in the CIE in the NHRP Registration Reply.
Due to the possible existence of asymmetric routing, an NHRP
Registration Reply may not be able to merely follow the routed path
back to the source protocol address specified in the common header of
the NHRP Registration Reply. As a result, there MUST exist a direct
NBMA level connection between the client and its NHS on which to send
the NHRP Registration Reply before NHRP Registration Reply may be
returned to the client. If such a connection does not exist then the
NHS must setup such a connection to he client by using the source
NBMA information supplied in the common header of the NHRP
Registration Request.
5.2.5 NHRP Purge Request
The NHRP Purge Request packet is sent in order to invalidate cached
information in a station. The NHRP Purge Request packet has a type
Luciani, Katz, Piscitello, Cole [Page 26]
INTERNET-DRAFT NBMA NHRP Expires December 1996
code of 5. The mandatory part of an NHRP Purge Request is coded as
described in Section 5.2.0.1. The message specific meanings of the
fields are as follows:
Flags - The flags field is coded as follows:
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|N| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
N
When set, this bit tells the receiver of the NHRP Purge Request
that the requester does not expect to receive an NHRP Purge
Reply. If an unsolicited NHRP Purge Reply is received by a
station where that station is identified in the Source Protocol
Address of the packet then that packet must be ignored.
One or more CIEs are specified in the NHRP Purge Request. Each CIE
contains next hop information which is to be purged from an NHS/NHC
cache. Generally, all fields in CIEs enclosed in NHRP Purge Requests
are coded as described in Section 5.2.0.1. Below, further
clarification is given for some fields in a CIE in the context of a
NHRP Purge Request.
Code
This field is set to 0x00 in NHRP Purge Requests.
Prefix Length
In the case of NHRP Purge Requests, the Prefix Length specifies
the equivalence class of addresses which match the first "Prefix
Length" bit positions of the Client Protocol Address specified in
the CIE. All next hop information which contains a protocol
address which matches an element of this equivalence class is to
be purged from the receivers cache. If this field is set to 0x00
then this field MUST be ignored and no equivalence information is
assumed.
The Maximum Transmission Unit and Preference fields of the CIE are
coded as zero. The Holding Time should be coded as zero but there
may be some utility in supplying a "short" holding time to be
applied to the matching next hop information before that
information would be purged; this usage is for further study. The
Client Protocol Address field and the Cli Proto Len field MUST be
filled in. The Client Protocol Address is filled in with the
protocol address to be purged from the receiving station's cache
Luciani, Katz, Piscitello, Cole [Page 27]
INTERNET-DRAFT NBMA NHRP Expires December 1996
while the Cli Proto Len is set the length of the purged client's
protocol address. All remaining fields in the CIE MAY be set to
zero although the client NBMA information (and associated length
fields) MAY be specified to narrow the scope of the NHRP Purge
Request if requester desires. However, the receiver of an NHRP
Purge Request may choose to ignore the Client NBMA information if
it is supplied.
An NHRP Purge Request packet is sent from an NHS to a station to
cause it to delete previously cached information. This is done when
the information may be no longer valid (typically when the NHS has
previously provided next hop information for a station that is not
directly connected to the NBMA subnetwork, and the egress point to
that station may have changed).
An NHRP Purge Request packet may also be sent from a client to an NHS
with which the client had previously registered. This allows for a
client to invalidate its registration with NHRP before it would
otherwise expire via the holding timer.
The station sending the NHRP Purge Request MAY periodically
retransmit the NHRP Purge Request until either NHRP Purge Request is
acknowledged or until the holding time of the information being
purged has expired. Retransmission strategies for NHRP Purge
Requests are a local matter.
When a station receives an NHRP Purge Request, it MUST discard any
previously cached information that matches the information in the
CIEs.
An NHRP Purge Reply MUST be returned for the NHRP Purge Request even
if the station does not have a matching cache entry assuming that the
"N" bit is off in the NHRP Purge Request.
If the station wishes to reestablish communication with the
destination shortly after receiving an NHRP Purge Request, it should
make an authoritative Next Hop Resolution Request in order to avoid
any stale cache entries that might be present in intermediate NHSs
(See section 6.2.2.). It is recommended that authoritative Next Hop
Resolution Requests be made for the duration of the holding time of
the old information.
5.2.6 NHRP Purge Reply
The NHRP Purge Reply packet is sent in order to assure the sender of
an NHRP Purge Request that all cached information of the specified
type has been purged from the station sending the reply. The NHRP
Purge Reply has a type code of 6.
Luciani, Katz, Piscitello, Cole [Page 28]
INTERNET-DRAFT NBMA NHRP Expires December 1996
An NHRP Purge Reply is formed from an NHRP Purge Request by merely
changing the type code in the request to 6. The packet is then
returned to the requester after filling in the appropriate extensions
if they exist.
5.2.7 NHRP Error Indication
The NHRP Error Indication is used to convey error indications to the
sender of an NHRP packet. It has a type code of 7. The Mandatory
Part has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Src Proto Len | Dst Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Error Code | Error Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Contents of NHRP Packet in error (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Src Proto Len
This field holds the length in octets of the Source Protocol
Address.
Dst Proto Len
This field holds the length in octets of the Destination Protocol
Address.
Error Code
An error code indicating the type of error detected, chosen from
the following list:
1 - Unrecognized Extension
When the Compulsory bit of an extension in NHRP packet is set,
the NHRP packet cannot be processed unless the extension has
been processed. The responder MUST return an NHRP Error
Indication of type Unrecognized Extension if it is incapable of
Luciani, Katz, Piscitello, Cole [Page 29]
INTERNET-DRAFT NBMA NHRP Expires December 1996
processing the extension. However, if a transit NHS (one which
is not going to generate a reply) detects an unrecognized
extension, it SHALL ignore the extension.
2 - Subnetwork ID Mismatch
This error occurs when the current station receives an NHRP
packet whose NBMA subnetwork identifier matches none of the
locally known identifiers for the NBMA subnetwork on which the
packet is received.
3 - NHRP Loop Detected
A Loop Detected error is generated when it is determined that
an NHRP packet is being forwarded in a loop.
6 - Protocol Address Unreachable
This error occurs when a packet it moving along the routed path
and it reaches a point such that the protocol address of
interest is not reachable.
7 - Protocol Error
A generic packet processing error has occurred (e.g., invalid
version number, invalid protocol type, failed checksum, etc.)
8 - NHRP SDU Size Exceeded
If the SDU size of the NHRP packet exceeds the MTU size of the
NBMA network then this error is returned.
9 - Invalid Extension
If an NHS finds an extension in a packet which is inappropriate
for the packet type, an error is sent back to the sender with
Invalid Extension as the code.
10- Invalid Next Hop Resolution Reply Received
If a client receives a Next Hop Resolution Reply for a Next Hop
Resolution Request which it believes it did not make then an
error packet is sent to the station making the reply with an
error code of Invalid Reply Received.
11- Authentication Failure
If a received packet fails an authentication test then this
Luciani, Katz, Piscitello, Cole [Page 30]
INTERNET-DRAFT NBMA NHRP Expires December 1996
error is returned.
14- Hop Count Exceeded
The hop count which was specified in the Fixed Header of an
NHRP message has been exceeded.
Error Offset
The offset in octets into the NHRP packet, starting at the NHRP
Fixed Header, at which the error was detected.
Source NBMA Address
The Source NBMA address field is the address of the station which
observed the error.
Source NBMA SubAddress
The Source NBMA subaddress field is the address of the station
which observed the error. If the field's length as specified in
ar$sstl is 0 then no storage is allocated for this address at all.
Source Protocol Address
This is the protocol address of the station which issued the Error
packet.
Destination Protocol Address
This is the protocol address of the station which sent the packet
which was found to be in error.
An NHRP Error Indication packet SHALL NEVER be generated in response
to another NHRP Error Indication packet. When an NHRP Error
Indication packet is generated, the offending NHRP packet SHALL be
discarded. In no case should more than one NHRP Error Indication
packet be generated for a single NHRP packet.
If an NHS sees its own Protocol and NBMA Addresses in the Source NBMA
and Source Protocol address fields of a transiting NHRP Error
Indication packet then the NHS will quietly drop the packet and do
nothing (this scenario would occur when the NHRP Error Indication
packet was itself in a loop).
Note that no extensions may be added to an NHRP Error Indication.
5.3 Extensions Part
The Extensions Part, if present, carries one or more extensions in
{Type, Length, Value} triplets. Extensions are only present in a
"reply" if they were present in the corresponding "request";
Luciani, Katz, Piscitello, Cole [Page 31]
INTERNET-DRAFT NBMA NHRP Expires December 1996
therefore, minimal NHRP client implementations which do not also act
as an NHS and do not transmit extensions need not be able to receive
extensions. The previous statement is not intended to preclude the
creation of NHS-only extensions which might be added to and removed
from NHRP packets by the same NHS; such extensions MUST not be
propagated to clients. An implementation that is incapable of
processing extensions SHALL return an NHRP Error Indication of type
Unrecognized Extension when it receives an NHRP packet containing
extensions.
Extensions have the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C|u| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
C
"Compulsory." If clear, and the NHS does not recognize the type
code, the extension may safely be ignored. If set, and the NHS
does not recognize the type code, the NHRP "request" is considered
to be in error. (See below for details.)
u
Unused and must be set to zero.
Type
The extension type code (see below). The extension type is not
qualified by the Compulsory bit, but is orthogonal to it.
Length
The length in octets of the value (not including the Type and
Length fields; a null extension will have only an extension header
and a length of zero).
When extensions exist, the extensions list is terminated by the Null
TLV, having Type = 0 and Length = 0.
Extensions may occur in any order, but any particular extension type
(except for the vendor-private extension) may occur only once in an
NHRP packet. The vendor-private extension may occur multiple times
in a packet in order to allow for extensions which do not share the
same vendor ID to be represented.
Luciani, Katz, Piscitello, Cole [Page 32]
INTERNET-DRAFT NBMA NHRP Expires December 1996
The Compulsory bit provides for a means to add to the extension set.
If the bit is set, the NHRP message cannot be properly processed by
the station responding to the message (e.g., the station that would
issue a Next Hop Resolution Reply in response to a Next Hop
Resolution Request) without processing the extension. As a result,
the responder MUST return an NHRP Error Indication of type
Unrecognized Extension. If the Compulsory bit is clear then the
extension can be safely ignored; however, if an ignored extension is
in a "request" then it MUST be returned, unchanged, in the
corresponding "reply" packet type.
If a transit NHS (one which is not going to generate a "reply")
detects an unrecognized extension, it SHALL ignore the extension. If
the Compulsory bit is set, the transit NHS MUST NOT cache the
information contained in the packet and MUST NOT identify itself as
an egress router (in the Forward Record or Reverse Record
extensions). Effectively, this means, if a transit NHS encounters an
extension which it cannot process and which has the Compulsory bit
set then that NHS MUST NOT participate in any way in the protocol
exchange other than acting as a forwarding agent.
Use of NHRP extension Types in the range 8192 to 16383 are reserved
for research or use in other protocol development and will be
administered by IANA.
5.3.0 The End Of Extensions
Compulsory = 1
Type = 0
Length = 0
When extensions exist, the extensions list is terminated by the End
Of Extensions/Null TLV.
5.3.1 Extension with Type 1 not assigned.
5.3.2 NBMA Subnetwork ID Extension
Compulsory = 1
Type = 2
Length = variable
This extension is used to carry one or more identifiers for the NBMA
subnetwork. This can be used as a validity check to ensure that an
NHRP packet does not leave a particular NBMA subnetwork. The
extension is placed in a "request" packet with an ID value of zero.
The first NHS along the routed path fills in the field with the
identifier(s) for the NBMA subnetwork.
Luciani, Katz, Piscitello, Cole [Page 33]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Multiple NBMA Subnetwork IDs may be used as a transition mechanism
while NBMA Subnetworks are being split or merged.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NBMA Subnetwork ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
...
Each identifier consists of a 32 bit globally unique value assigned
to the NBMA subnetwork. This value may be chosen from the
internetworking layer address space administered by the operators of
the NBMA subnetwork if such an address can fit into a 32 bit field.
This value is used for identification only, not for routing or any
other purpose.
Each NHS processing a "request" or "reply" SHALL verify these values.
If the value is not zero and none of the values matches the NHS's
NBMA Subnetwork ID, the NHS SHALL return an NHRP Error Indication to
the entity identified in Source Protocol Address if the packet type
is a "request" and to the Destination Protocol Address if the packet
type is a "reply". The error indicated in this case is "Subnetwork
ID Mismatch". The packet is discarded by the station sending the
NHRP Error Indication.
When an NHS is building a "reply" and the NBMA Subnetwork ID
extension is present in the correspond "request" then the NBMA
Subnetwork ID extension SHALL be copied from the "request" to the
"reply".
5.3.3 Responder Address Extension
Compulsory = 1
Type = 3
Length = variable
This extension is used to determine the address of the NHRP
responder; i.e., the entity that generates the appropriate "reply"
packet for a given "request" packet. In the case of an Next Hop
Resolution Request, the station responding may be different (in the
case of cached replies) than the system identified in the Next Hop
field of the Next Hop Resolution Reply. Further, this extension may
aid in detecting loops in the NHRP forwarding path.
Luciani, Katz, Piscitello, Cole [Page 34]
INTERNET-DRAFT NBMA NHRP Expires December 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Res Addr T/L | Res SAddr T/L| Res Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Responder NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Responder NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Responder Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Holding Time
The Holding Time field specifies the number of seconds for which
the NBMA information is considered to be valid. Cached information
SHALL be discarded when the holding time expires.
Res Addr T/L
Type & length of the responder NHS's NBMA address interpreted in
the context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0003 for ATM). When the address length is
specified as 0 no storage is allocated for the address.
Res SAddr T/L
Type & length of responder NHS's NBMA subaddress interpreted in the
context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0015 for ATM makes the address an E.164 and the
subaddress an ATM Forum NSAP address). When an NBMA technology has
no concept of a subaddress, the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
Res Proto Len
This field holds the length in octets of responding NHS's Protocol
Address.
Responder NBMA Address
This is the NBMA address of the responding NHS.
Responder NBMA SubAddress
This is the NBMA subaddress of the responding NHS.
Responder Protocol Address
This is the Protocol Address of responding NHS.
If a "requester" desires this information, the "requester" SHALL
Luciani, Katz, Piscitello, Cole [Page 35]
INTERNET-DRAFT NBMA NHRP Expires December 1996
include this extension with a value of zero. Note that this implies
that no storage is allocated for the Holding Time and Type/Length
fields until the "Value" portion of the extension is filled out.
If an NHS is generating a "reply" packet in response to a "request"
containing this extension, the NHS SHALL include this extension,
containing its protocol address in the "reply". If an NHS has more
than one protocol address, it SHALL use the same protocol address
consistently in all of the Responder Address, Forward NHS Record, and
Reverse NHS Record extensions. The choice of which of several
protocol address to include in this extension is a local matter.
If an NHRP Next Hop Resolution Reply packet being forwarded by an NHS
contains a protocol address of that NHS in the Responder Address
Extension then that NHS SHALL generate an NHRP Error Indication of
type "NHRP Loop Detected" and discard the Next Hop Resolution Reply.
If an NHRP Next Hop Resolution Reply packet is being returned by an
intermediate NHS based on cached data, it SHALL place its own address
in this extension (differentiating it from the address in the Next
Hop field).
5.3.4 NHRP Forward Transit NHS Record Extension
Compulsory = 1
Type = 4
Length = variable
The NHRP Forward Transit NHS record contains a list of transit NHSs
through which a "request" has traversed. Each NHS SHALL append to
the extension a Forward Transit NHS element (as specified below)
containing its Protocol address The extension length field and the
ar$chksum fields SHALL be adjusted appropriately.
The responding NHS, as described in Section 5.3.3, SHALL NOT update
this extension.
In addition, NHSs that are willing to act as egress routers for
packets from the source to the destination SHALL include information
about their NBMA Address.
The Forward Transit NHS element has the following form:
Luciani, Katz, Piscitello, Cole [Page 36]
INTERNET-DRAFT NBMA NHRP Expires December 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Addr T/L | NHS SAddr T/L| NHS Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Holding Time
The Holding Time field specifies the number of seconds for which
the NBMA information is considered to be valid. Cached information
SHALL be discarded when the holding time expires.
NHS Addr T/L
Type & length of the transit NHS's NBMA address interpreted in the
context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0003 for ATM). When the address length is
specified as 0 no storage is allocated for the address.
NHS SAddr T/L
Type & length of the transit NHS's NBMA subaddress interpreted in
the context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0015 for ATM makes the address an E.164 and the
subaddress an ATM Forum NSAP address). When an NBMA technology has
no concept of a subaddress the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
NHS Proto Len
This field holds the length in octets of the transit NHS's Protocol
Address.
NHS NBMA Address
This is the NBMA address of the transit NHS.
NHS NBMA SubAddress
This is the NBMA subaddress of the transit NHS.
NHS Protocol Address
This is the Protocol Address of the transit NHS.
If a "requester" wishes to obtain this information, it SHALL include
Luciani, Katz, Piscitello, Cole [Page 37]
INTERNET-DRAFT NBMA NHRP Expires December 1996
this extension with a length of zero. Note that this implies that no
storage is allocated for the Holding Time and Type/Length fields
until the "Value" portion of the extension is filled out.
If an NHS has more than one Protocol address, it SHALL use the same
Protocol address consistently in all of the Responder Address,
Forward NHS Record, and Reverse NHS Record extensions. The choice of
which of several Protocol addresses to include in this extension is a
local matter.
If a "request" that is being forwarded by an NHS contains the
Protocol Address of that NHS in one of the Forward Transit NHS
elements then the NHS SHALL generate an NHRP Error Indication of type
"NHRP Loop Detected" and discard the "request".
5.3.5 NHRP Reverse Transit NHS Record Extension
Compulsory = 1
Type = 5
Length = variable
The NHRP Reverse Transit NHS record contains a list of transit NHSs
through which a "reply" has traversed. Each NHS SHALL append a
Reverse Transit NHS element (as specified below) containing its
Protocol address to this extension. The extension length field and
ar$chksum SHALL be adjusted appropriately.
The responding NHS, as described in Section 5.3.3, SHALL NOT update
this extension.
In addition, NHSs that are willing to act as egress routers for
packets from the source to the destination SHALL include information
about their NBMA Address.
The Reverse Transit NHS element has the following form:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused | Holding Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Addr T/L | NHS SAddr T/L| NHS Proto Len | unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS NBMA Subaddress (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NHS Protocol Address (variable length) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Luciani, Katz, Piscitello, Cole [Page 38]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Holding Time
The Holding Time field specifies the number of seconds for which
the NBMA information is considered to be valid. Cached information
SHALL be discarded when the holding time expires.
NHS Addr T/L
Type & length of the responding NHS's NBMA address interpreted in
the context of the 'address family number'[6] indicated by ar$afn
(e.g., ar$afn=0x0003 for ATM). When the address length is
specified as 0 no storage is allocated for the address.
NHS SAddr T/L
Type & length of the responding NHS's NBMA subaddress interpreted
in the context of the 'address family number'[6] indicated by
ar$afn (e.g., ar$afn=0x0015 for ATM makes the address an E.164 and
the subaddress an ATM Forum NSAP address). When an NBMA technology
has no concept of a subaddress the subaddress is always null with a
length of 0. When the address length is specified as 0 no storage
is allocated for the address.
NHS Proto Len
This field holds the length in octets of the transit NHS's Protocol
Address.
NHS NBMA Address
This is the NBMA address of the transit NHS.
NHS NBMA SubAddress
This is the NBMA subaddress of the transit NHS.
NHS Protocol Address
This is the Protocol Address of the transit NHS.
If a "requester" wishes to obtain this information, it SHALL include
this extension with a length of zero. Note that this implies that no
storage is allocated for the Holding Time and Type/Length fields
until the "Value" portion of the extension is filled out.
If an NHS has more than one Protocol address, it SHALL use the same
Protocol address consistently in all of the Responder Address,
Forward NHS Record, and Reverse NHS Record extensions. The choice of
which of several Protocol addresses to include in this extension is a
local matter.
If a "reply" that is being forwarded by an NHS contains the Protocol
Address of that NHS in one of the Reverse Transit NHS elements then
the NHS SHALL generate an NHRP Error Indication of type "NHRP Loop
Detected" and discard the "reply".
Luciani, Katz, Piscitello, Cole [Page 39]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Note that this information may be cached at intermediate NHSs; if
so, the cached value SHALL be used when generating a reply.
5.3.6 NHRP QoS Extension
Compulsory = 0
Type = 6
Length = variable
The NHRP QoS Extension is carried in Next Hop Resolution Request
packets to indicate the desired QoS of the path to the indicated
destination. This information may be used to help select the
appropriate NBMA Next Hop.
It may also be carried in NHRP Register Request packets to indicate
the QoS to which the registration applies.
The syntax and semantics of this extension are TBD; alignment with
resource reservation may be useful.
5.3.7 NHRP Authentication Extension
Compulsory = 1
Type = 7
Length = variable
The NHRP Authentication Extension is carried in NHRP packets to
convey authentication information between NHRP speakers. The
Authentication Extension may be included in any NHRP "request" or
"reply".
Except in the case of an NHRP Registration Request/Reply
Authentication is done pairwise on an NHRP hop-by-hop basis; i.e.,
the authentication extension is regenerated at each hop. In the case
of an NHRP Registration Request/Reply, the Authentication is checked
on an end-to-end basis rather than hop-by-hop. If a received packet
fails the authentication test, the station SHALL generate an Error
Indication of type "Authentication Failure" and discard the packet.
Note that one possible authentication failure is the lack of an
Authentication Extension; the presence or absence of the
Authentication Extension is a local matter.
Luciani, Katz, Piscitello, Cole [Page 40]
INTERNET-DRAFT NBMA NHRP Expires December 1996
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Authentication Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+ Authentication Data... -+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Authentication Type field identifies the authentication method in
use. Currently assigned values are:
1 - Cleartext Password
2 - Keyed MD5
All other values are reserved.
The Authentication Data field contains the type-specific
authentication information.
In the case of Cleartext Password Authentication, the Authentication
Data consists of a variable length password.
In the case of Keyed MD5 Authentication, the Authentication Data
contains the 16 byte MD5 digest of the entire NHRP packet, including
the encapsulated protocol's header, with the authentication key
appended to the end of the packet. The authentication key is not
transmitted with the packet.
Distribution of authentication keys is outside the scope of this
document.
5.3.8 NHRP Vendor-Private Extension
Compulsory = 0
Type = 8
Length = variable
The NHRP Vendor-Private Extension is carried in NHRP packets to
convey vendor-private information or NHRP extensions between NHRP
speakers.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor ID | Data.... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Luciani, Katz, Piscitello, Cole [Page 41]
INTERNET-DRAFT NBMA NHRP Expires December 1996
Vendor ID
802 Vendor ID as assigned by the IEEE [6]
Data
The remaining octets after the Vendor ID in the payload are
vendor-dependent data.
This extension may be added to any "request" or "reply" packet and it
is the only extension that may be included multiple times. If the
receiver does not handle this extension, or does not match the Vendor
ID in the extension then the extension may be completely ignored by
the receiver. If a Vendor Private Extension is included in a
"request" then is must be copied in the corresponding "reply".
5.3.9 Extension with Type 9 not assigned.
6. Protocol Operation
In this section, we discuss certain operational considerations of
NHRP.
6.1 Router-to-Router Operation
In practice, the initiating and responding stations may be either
hosts or routers. However, there is a possibility under certain
conditions that a stable routing loop may occur if NHRP is used
between two routers. In particular, attempting to establish an NHRP
path across a boundary where information used in route selection is
lost may result in a routing loop. Such situations include the loss
of BGP path vector information, the interworking of multiple routing
protocols with dissimilar metrics (e.g, RIP and OSPF), etc. In such
circumstances, NHRP should not be used. This situation can be
avoided if there are no "back door" paths between the entry and
egress router outside of the NBMA subnetwork. Protocol mechanisms to
relax these restrictions are under investigation.
In general it is preferable to use mechanisms, if they exist, in
routing protocols to resolve the egress point when the destination
lies outside of the NBMA subnetwork, since such mechanisms will be
more tightly coupled to the state of the routing system and will
probably be less likely to create loops.
6.2 Cache Management Issues
The management of NHRP caches in the source station, the NHS serving
the destination, and any intermediate NHSs is dependent on a number
of factors.
Luciani, Katz, Piscitello, Cole [Page 42]
INTERNET-DRAFT NBMA NHRP Expires December 1996
6.2.1 Caching Requirements
Source Stations
Source stations MUST cache all received Next Hop Resolution Replies
that they are actively using. They also must cache "incomplete"
entries, i.e., those for which a Next Hop Resolution Request has
been sent but which a Next Hop Resolution Reply has not been
received. This is necessary in order to preserve the Request ID
for retries, and provides the state necessary to avoid triggering
Next Hop Resolution Requests for every data packet sent to the
destination.
Source stations MUST purge expired information from their caches.
Source stations MUST purge the appropriate cached information upon
receipt of an NHRP Purge Request packet.
When a station has a co-resident client and NHS, the station may
reply to Next Hop Resolution Requests with information which the
station cached as a result of the station making its own Next Hop
Resolution Requests and receiving its own Next Hop Resolution
Replies as long as the station follows the rules for Transit NHSs
as seen below.
Serving NHSs
The NHS serving the destination (the one which responds
authoritatively to Next Hop Resolution Requests) SHOULD cache
information about all Next Hop Resolution Requests to which it has
responded if the information in the Next Hop Resolution Reply has
the possibility of changing during its lifetime (so that an NHRP
Purge Request packet can be sent). The NBMA information provided
by the source station in the Next Hop Resolution Request may be
cached for the duration of its holding time. This information is
considered to be stable, since it identifies a station directly
attached to the NBMA subnetwork. An example of unstable
information is NBMA information derived from a routing table, where
that routing table information has not been guaranteed to be stable
through administrative means.
Transit NHSs
A Transit NHS (lying along the NHRP path between the source station
and the responding NHS) may cache information contained in Next Hop
Resolution Request packets that it forwards. A Transit NHS may
cache information contained in Next Hop Resolution Reply packets
that it forwards only if that Next Hop Resolution Reply has the
Stable (B) bit set. It MUST discard any cached information whose
Luciani, Katz, Piscitello, Cole [Page 43]
INTERNET-DRAFT NBMA NHRP Expires December 1996
holding time has expired. It may return cached information in
response to non-authoritative Next Hop Resolution Requests only.
6.2.2 Dynamics of Cached Information
NBMA-Connected Destinations
NHRP's most basic function is that of simple NBMA address
resolution of stations directly attached to the NBMA subnetwork.
These mappings are typically very static, and appropriately chosen
holding times will minimize problems in the event that the NBMA
address of a station must be changed. Stale information will cause
a loss of connectivity, which may be used to trigger an
authoritative Next Hop Resolution Request and bypass the old data.
In the worst case, connectivity will fail until the cache entry
times out.
This applies equally to information marked in Next Hop Resolution
Replies as being "stable" (via the "B" bit).
This also applies equally well to source stations that are routers
as well as those which are hosts.
Note that the information carried in the Next Hop Resolution
Request packet is always considered "stable" because it represents
a station that is directly connected to the NBMA subnetwork.
Destinations Off of the NBMA Subnetwork
If the source of a Next Hop Resolution Request is a host and the
destination is not directly attached to the NBMA subnetwork, and
the route to that destination is not considered to be "stable," the
destination mapping may be very dynamic (except in the case of a
subnetwork where each destination is only singly homed to the NBMA
subnetwork). As such the cached information may very likely become
stale. The consequence of stale information in this case will be a
suboptimal path (unless the internetwork has partitioned or some
other routing failure has occurred).
6.3 Use of the Prefix Length field of a CIE
A certain amount of care needs to be taken when using the Prefix
Length field of a CIE, in particular with regard to the prefix length
advertised (and thus the size of the equivalence class specified by
it). Assuming that the routers on the NBMA subnetwork are exchanging
routing information, it should not be possible for an NHS to create a
black hole by advertising too large of a set of destinations, but
suboptimal routing (e.g., extra internetwork layer hops through the
Luciani, Katz, Piscitello, Cole [Page 44]
INTERNET-DRAFT NBMA NHRP Expires December 1996
NBMA) can result. To avoid this situation an NHS that wants to send
the Prefix Length MUST obey the following rule:
The NHS examines the Network Layer Reachability Information (NLRI)
associated with the route that the NHS would use to forward towards
the destination (as specified by the Destination internetwork layer
address in the Next Hop Resolution Request), and extracts from this
NLRI the shortest address prefix such that: (a) the Destination
internetwork layer address (from the Next Hop Resolution Request)
is covered by the prefix, (b) the NHS does not have any routes with
NLRI that forms a subset of what is covered by the prefix. The
prefix may then be used in the CIE.
The Prefix Length field of the CIE should be used with restraint, in
order to avoid NHRP stations choosing suboptimal transit paths when
overlapping prefixes are available. This document specifies the use
of the prefix length only when all the destinations covered by the
prefix are "stable". That is, either:
(a) All destinations covered by the prefix are on the NBMA network, or
(b) All destinations covered by the prefix are directly attached to
the NHRP responding station.
Use of the Prefix Length field of the CIE in other circumstances is
outside the scope of this document.
6.4 Domino Effect
One could easily imagine a situation where a router, acting as an
ingress station to the NBMA subnetwork, receives a data packet, such
that this packet triggers an Next Hop Resolution Request. If the
router forwards this data packet without waiting for an NHRP transit
path to be established, then when the next router along the path
receives the packet, the next router may do exactly the same -
originate its own Next Hop Resolution Request (as well as forward the
packet). In fact such a data packet may trigger Next Hop Resolution
Request generation at every router along the path through an NBMA
subnetwork. We refer to this phenomena as the NHRP "domino" effect.
The NHRP domino effect is clearly undesirable. At best it may result
in excessive NHRP traffic. At worst it may result in an excessive
number of virtual circuits being established unnecessarily.
Therefore, it is important to take certain measures to avoid or
suppress this behavior. NHRP implementations for NHSs MUST provide a
mechanism to address this problem. One possible strategy to address
this problem would be to configure a router in such a way that Next
Hop Resolution Request generation by the router would be driven only
Luciani, Katz, Piscitello, Cole [Page 45]
INTERNET-DRAFT NBMA NHRP Expires December 1996
by the traffic the router receives over its non-NBMA interfaces
(interfaces that are not attached to an NBMA subnetwork). Traffic
received by the router over its NBMA-attached interfaces would not
trigger NHRP Next Hop Resolution Requests. Such a router avoids the
NHRP domino effect through administrative means.
7. NHRP over Legacy BMA Networks
There would appear to be no significant impediment to running NHRP
over legacy broadcast subnetworks. There may be issues around
running NHRP across multiple subnetworks. Running NHRP on broadcast
media has some interesting possibilities; especially when setting up
a cut-through for inter-ELAN inter-LIS/LAG traffic when one or both
end stations are legacy attached. This use for NHRP requires further
research.
8. Security Considerations
As in any routing protocol, there are a number of potential security
attacks possible. Plausible examples include denial-of-service
attacks, and masquerade attacks using register and purge packets.
The use of authentication on all packets is recommended to avoid such
attacks.
The authentication schemes described in this document are intended to
allow the receiver of a packet to validate the identity of the
sender; they do not provide privacy or protection against replay
attacks.
Detailed security analysis of this protocol is for further study.
9. Discussion
The result of an Next Hop Resolution Request depends on how routing
is configured among the NHSs of an NBMA subnetwork. If the
destination station is directly connected to the NBMA subnetwork and
the the routed path to it lies entirely within the NBMA subnetwork,
the Next Hop Resolution Replies always return the NBMA address of the
destination station itself rather than the NBMA address of some
egress router. On the other hand, if the routed path exits the NBMA
subnetwork, NHRP will be unable to resolve the NBMA address of the
destination, but rather will return the address of the egress router.
For destinations outside the NBMA subnetwork, egress routers and
routers in the other subnetworks should exchange routing information
so that the optimal egress router may be found.
Luciani, Katz, Piscitello, Cole [Page 46]
INTERNET-DRAFT NBMA NHRP Expires December 1996
In addition to NHSs, an NBMA station could also be associated with
one or more regular routers that could act as "connectionless
servers" for the station. The station could then choose to resolve
the NBMA next hop or just send the packets to one of its
connectionless servers. The latter option may be desirable if
communication with the destination is short-lived and/or doesn't
require much network resources. The connectionless servers could, of
course, be physically integrated in the NHSs by augmenting them with
internetwork layer switching functionality.
References
[1] NBMA Address Resolution Protocol (NARP), Juha Heinanen and Ramesh
Govindan, RFC1735.
[2] Address Resolution Protocol, David C. Plummer, RFC 826.
[3] Classical IP and ARP over ATM, Mark Laubach, RFC 1577.
[4] Transmission of IP datagrams over the SMDS service, J. Lawrence
and D. Piscitello, RFC 1209.
[5] Protocol Identification in the Network Layer, ISO/IEC TR
9577:1990.
[6] Assigned Numbers, J. Reynolds and J. Postel, RFC 1700.
[7] Multiprotocol Encapsulation over ATM Adaptation Layer 5, J. Heinanen,
RFC1483.
[8] Multiprotocol Interconnect on X.25 and ISDN in the Packet Mode,
A. Malis, D. Robinson, and R. Ullmann, RFC1356.
[9] Multiprotocol Interconnect over Frame Relay, T. Bradley, C. Brown, and
A. Malis, RFC1490.
[10] "Local/Remote" Forwarding Decision in Switched Data Link Subnetworks,
Yakov Rekhter, Dilip Kandlur, RFCxxxx.
Acknowledgments
We would like to thank Juha Heinenan of Telecom Finland and Ramesh
Govidan of ISI for their work on NBMA ARP and the original NHRP
draft, which served as the basis for this work. Russell Gardo of
IBM, John Burnett of Adaptive, Dennis Ferguson of ANS, Joel Halpern
Luciani, Katz, Piscitello, Cole [Page 47]
INTERNET-DRAFT NBMA NHRP Expires December 1996
of Newbridge, Paul Francis of NTT, Tony Li and Yakov Rekhter of
cisco, and Grenville Armitage of Bellcore should also be acknowledged
for comments and suggestions that improved this work substantially.
We would also like to thank the members of the ION working group of
the IETF, whose review and discussion of this document have been
invaluable.
Authors' Addresses
James V. Luciani Dave Katz
Bay Networks cisco Systems
3 Federal Street 170 W. Tasman Dr.
Mail Stop: BL3-04 San Jose, CA 95134 USA
Billerica, MA 01821 Phone: +1 408 526 8284
Phone: +1 508 439 4737 Email: dkatz@cisco.com
Email: luciani@baynetworks.com
David Piscitello Bruce Cole
Core Competence cisco Systems
1620 Tuckerstown Road 170 W. Tasman Dr.
Dresher, PA 19025 USA San Jose, CA 95134 USA
Phone: +1 215 830 0692Phone: Phone: +1 408 526 4000
Email: dave@corecom.comEmail: Email: bcole@cisco.com
Luciani, Katz, Piscitello, Cole [Page 48]