ROLL P. Thubert, Ed.
Internet-Draft Cisco Systems
Updates: 6550 (if approved) R.A. Jadhav
Intended status: Standards Track Huawei Tech
Expires: 12 November 2020 M. Gillmore
Itron
11 May 2020
Root initiated routing state in RPL
draft-ietf-roll-dao-projection-10
Abstract
This document enables a RPL Root to install and maintain Projected
Routes within its DODAG, along a selected set of nodes that may or
may not include self, for a chosen duration. This potentially
enables routes that are more optimized or resilient than those
obtained with the classical distributed operation of RPL, either in
terms of the size of a source-route header or in terms of path
length, which impacts both the latency and the packet delivery ratio.
Projected Routes may be installed in either Storing and Non-Storing
Modes Instances of the classical RPL operation, resulting in
potentially hybrid situations where the mode of some Projected Routes
is different from that of the other routes in the RPL Instance.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 12 November 2020.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
Thubert, et al. Expires 12 November 2020 [Page 1]
Internet-Draft DAO Projection May 2020
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Simplified BSD License text
as described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1. BCP 14 . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2. References . . . . . . . . . . . . . . . . . . . . . . . 5
2.3. Other Terms . . . . . . . . . . . . . . . . . . . . . . . 5
2.4. Glossary . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Updating RFC 6550 . . . . . . . . . . . . . . . . . . . . . . 6
4. Identifying a Path . . . . . . . . . . . . . . . . . . . . . 7
5. New RPL Control Messages and Options . . . . . . . . . . . . 8
5.1. New P-DAO Request Control Message . . . . . . . . . . . . 8
5.2. New PDR-ACK Control Message . . . . . . . . . . . . . . . 8
5.3. Route Projection Options . . . . . . . . . . . . . . . . 10
5.4. Sibling Information Option . . . . . . . . . . . . . . . 12
6. Projected DAO . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1. Non-Storing Mode Projected Route . . . . . . . . . . . . 15
6.2. Storing-Mode Projected Route . . . . . . . . . . . . . . 17
7. Security Considerations . . . . . . . . . . . . . . . . . . . 19
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
8.1. New RPL Control Codes . . . . . . . . . . . . . . . . . . 19
8.2. New RPL Control Message Options . . . . . . . . . . . . . 19
8.3. New SubRegistry for the Projected DAO Request (PDR)
Flags . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.4. New SubRegistry for the PDR-ACK Flags . . . . . . . . . . 20
8.5. New Subregistry for the PDR-ACK Acceptance Status
values . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.6. New Subregistry for the PDR-ACK Rejection Status
values . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.7. New SubRegistry for the Route Projection Options (RPO)
Flags . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.8. New SubRegistry for the Sibling Information Option (SIO)
Flags . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.9. Error in Projected Route ICMPv6 Code . . . . . . . . . . 22
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 22
10. Normative References . . . . . . . . . . . . . . . . . . . . 23
11. Informative References . . . . . . . . . . . . . . . . . . . 23
Appendix A. Applications . . . . . . . . . . . . . . . . . . . . 24
A.1. Loose Source Routing in Non-storing Mode . . . . . . . . 25
Thubert, et al. Expires 12 November 2020 [Page 2]
Internet-Draft DAO Projection May 2020
A.2. Transversal Routes in storing and non-storing modes . . . 26
Appendix B. Examples . . . . . . . . . . . . . . . . . . . . . . 28
B.1. Using storing mode P-DAO in non-storing mode MOP . . . . 28
B.2. Projecting a storing-mode transversal route . . . . . . . 29
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 31
1. Introduction
RPL, the "Routing Protocol for Low Power and Lossy Networks" [RPL]
(LLNs), is a generic Distance Vector protocol that is well suited for
application in a variety of low energy Internet of Things (IoT)
networks. RPL forms Destination Oriented Directed Acyclic Graphs
(DODAGs) in which the Root often acts as the Border Router to connect
the RPL domain to the Internet. The Root is responsible to select
the RPL Instance that is used to forward a packet coming from the
Internet into the RPL domain and set the related RPL information in
the packets.
The "6TiSCH architecture" [6TiSCH-ARCHI] leverages RPL for its
routing operations and considers the Deterministic Networking
Architecture [RFC8655] as one possible model whereby the device
resources and capabilities are exposed to an external controller
which installs routing states into the network based on some
objective functions that reside in that external entity. With DetNet
and 6TiSCH, the component of the controller that is responsible of
computing routes is called a Path Computation Element ([PCE]).
Based on heuristics of usage, path length, and knowledge of device
capacity and available resources such as battery levels and
reservable buffers, a PCE with a global visibility on the system can
compute P2P routes that are more optimized for the current needs as
expressed by the objective function. This draft proposes a protocol
extension to RPL that enables the Root to install a limited amount of
centrally-computed routes in a RPL graph, on behalf of a PCE that may
be collocated or separated from the Root. Those extensions enable
loose source routing down in RPL Non-Storing Mode and transversal
routes inside the DODAG regardless of the RPL Mode of Operation
(MOP).
Thubert, et al. Expires 12 November 2020 [Page 3]
Internet-Draft DAO Projection May 2020
The 6TiSCH architecture also introduces the concept of a Track that
is a complex path with possibly redundant forwarding solutions along
the way, exploiting Packet ARQ, Replication, Elimination, and
Overhearing (PAREO) functions. The "Reliable and Available Wireless
(RAW) Architecture/Framework" [RAW-ARCHI] separates the time scale at
which the PCE computes the Track (slow, globally optimized, with
statistical metrics) and the time scale at which the forwarding
decision is made for a packet or a small collection of packets (fast,
at the scale of the Track), to leverage the PAREO functions
dynamically and provide the required reliability and availability
while conserving energy and spectrum.
As opposed to the classical RPL operations where routes are injected
by the Target nodes, the protocol extension enables the Root of a
DODAG to project the routes that are needed onto the nodes where they
should be installed. This specification uses the term Projected
Route to refer to those routes. A Projected Route may be a stand-
alone end-to-end path to a Target or a segment in a more complex
Track.
Projected Routes must be used with the parsimony to limit the amount
of state that is installed in each device to fit within its
resources, and to limit the amount of rerouted traffic to fit within
the capabilities of the transmission links. The method to learn the
node capabilities and the resources that are available in the devices
and in the network are out of scope for this document.
In RPL Non-Storing Mode, the Root has enough information to build a
basic DODAG topology. This document adds the capability for nodes to
advertise sibling information in order to improve the topological
awareness of the Root. This specification uses the RPL Root as a
proxy to the PCE. The algorithm to compute the paths and the
protocol used by an external PCE to obtain the topology of the
network from the Root are out of scope for this document.
2. Terminology
2.1. BCP 14
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119][RFC8174] when, and only when, they appear in all
capitals, as shown here.
Thubert, et al. Expires 12 November 2020 [Page 4]
Internet-Draft DAO Projection May 2020
2.2. References
In this document, readers will encounter terms and concepts that are
discussed in the following documents:
* "Routing Protocol for Low Power and Lossy Networks" [RPL], and
* "Terminology in Low power And Lossy Networks" [RFC7102].
2.3. Other Terms
Projected Route: A Projected Route is a serial path that is computed
and installed remotely by a RPL Root.
Track: The term Track is used in this document to refer to a complex
path, e.g., a DODAG, that incorporates redundant Projected Routes
towards a destination using diversity to increase the reliability.
2.4. Glossary
This document often uses the following acronyms:
6BBR: 6LoWPAN Backbone Router
6LBR: 6LoWPAN Border Router
6LN: 6LoWPAN Node
6LR: 6LoWPAN Router
CMO: Control Message Option
DAD: Duplicate Address Detection
DAO: Destination Advertisement Object
DODAG: Destination-Oriented Directed Acyclic Graph
LLN: Low-Power and Lossy Network
MOP: RPL Mode of Operation
NA: Neighbor Advertisement
NCE: Neighbor Cache Entry
ND: Neighbor Discovery
NDP: Neighbor Discovery Protocol
NS: Neighbor Solicitation
P-DAO: A Projected DAO is a DAO message sent by the RPL Root to
install a Projected Route.
PDR P-DAO Request
RA: Router Advertisement
RAN: RPL-Aware Node
RS: Router Solicitation
RPL: IPv6 Routing Protocol for LLNs [RPL]
RPO: A Route Projection Option; it can be a VIO or an SRVIO.
RTO: RPL Target Option
SIO: RPL Sibling Information Option
Thubert, et al. Expires 12 November 2020 [Page 5]
Internet-Draft DAO Projection May 2020
SRVIO: A Source-Routed Via Information Option, used in Non-Storing
Mode P-DAO messages.
TIO: RPL Transit Information Option
VIO: A Via Information Option, used in Storing Mode P-DAO messages.
3. Updating RFC 6550
This specification introduces two new RPL Control Messages to enable
a RPL Aware Node (RAN) to request the establisment of a path from
self to a Target. A RAN may request the installation of a path by
sending a new P-DAO Request (PDR) Message to the Root. The Root
confirms with a new PDR-ACK message back to the requester RAN with a
completion status once it is done installing the path. See
Section 5.1 for more.
Section 6.7 of [RPL] specifies the RPL Control Message Options (CMO)
to be placed in RPL messages such as the Destination Advertisement
Object (DAO) message. The RPL Target Option (RTO) and the Transit
Information Option (TIO) are such options. In Non-Storing Mode, the
TIO option is used in the DAO message to indicate a parent within a
DODAG. The TIO applies to the RTOs that immedially preceed it in the
message. Options may be factorized; multiple TIOs may be present to
indicate multiple routes to the one or more contiguous addresses
indicated in the RTOs that immediately precede the TIOs in the RPL
message.
This specification introduces two new CMOs referred to as Route
Projection Options (RPO) to install Projected Routes. One RPO is the
Via Information Option (VIO) and the other is the Source-Routed VIO
(SRVIO). The VIO installs a route on each hop along a Projected
Route (in a fashion analogous to RPL Storing Mode) whereas the SRVIO
installs a source-routing state at the ingress node, which uses that
state to encapsulate a packet with an IPv6 Routing Header in a
fashion similar to RPL Non-Storing Mode. Like the TIO, the RPOs MUST
be preceded by exactly one RTO to which they apply, and they can be
factorized: multiple contiguous RPOs indicate alternate paths to the
Target, more in Section 5.3.
This specification also introduces a new CMO to enable a RAN to
advertise a selection of its candidate neighbors as siblings to the
Root, using a new Sibling Information Option (SIO) as specified in
Section 5.4.
Thubert, et al. Expires 12 November 2020 [Page 6]
Internet-Draft DAO Projection May 2020
4. Identifying a Path
It must be noted that RPL has a concept of Instance to represent
different routing topologies but does not have a concept of an
administrative distance, which exists in certain proprietary
implementations to sort out conflicts between multiple sources of
routing information within one routing topology.
This draft conforms the Instance model as follows:
* If the PCE needs to influence a particular Instance to add better
routes in conformance with the routing objectives in that
Instance, it may do so as long as it does not create a loop. A
Projected Route is always preferred over a route that is learned
via RPL.
* A PCE that installs a more specific (say, Traffic Engineered) and
possibly complex path (aka a Track) towards a particular Target
MUST use a Local RPL Instance (see section 5 of [RPL]) associated
to that Target to identify the path. We refer to that Local
RPLInstanceID as TrackID. A projected path is uniquely identified
within the RPL domain by the tuple (Target address, TrackID).
When packet is placed on a Track, a RPL Packet Information (RPI)
is added with the TrackID as RPLInstanceID. The RPLInstanceID has
the 'D' flag set, indicating that the destination address in the
IPv6 header is the Target that is used to identify the Track.
* A packet that is routed over a projected path MUST NOT be placed
over a different RPL Instance again. A packet that is placed on a
Global Instance MAY be injected in a Local Instance based on a
network policy and the Local Instance configuration.
A Projected Route is a serial path that may represent the end-to-end
route or only a segment in a complex Track, in which case multiple
Projected Routes are installed with the same tuple (Target address,
TrackID) and a different segment ID. A node that is present on more
than one segment in a Track may be able to use either of the
Projected Routes to forward towards the Target. The selection of the
best route in a Track at forwarding time is out of scope for this
document, but [RAW-ARCHI] elaborates on that particular problem.
All properties of a Track operations are inherited form the main
instance that is used to install the Track. For instance, the use of
compression per [RFC8138] is determined by whether it is used in the
main instance, e.g., by setting the "T" flag [TURN-ON_RFC8138] in the
RPL configuration option.
Thubert, et al. Expires 12 November 2020 [Page 7]
Internet-Draft DAO Projection May 2020
5. New RPL Control Messages and Options
5.1. New P-DAO Request Control Message
The PDR is sent to the Root to request a new Path. Exactly one
Target Options MUST be present.
The format of P-DAO Request (PDR) Base Object is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TrackID |K|R| Flags | PDRLifetime | PDRSequence |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option(s)...
+-+-+-+-+-+-+-+-+
Figure 1: New P-DAO Request Format
TrackID: 8-bit field indicating the RPLInstanceID associated with
the Track. It is set to zero upon the first request for a new
Track and then to the TrackID once the Track was created, to
either renew it of destroy it.
K: The 'K' flag is set to indicate that the recipient is expected to
send a PDR-ACK back.
R: The 'R' flag is set to indicate that the Requested path should be
redundant.
PDRLifetime: 8-bit unsigned integer. The requested lifetime for the
Track expressed in Lifetime Units (obtained from the Configuration
option). A PDR with a fresher PDRSequence refreshes the lifetime,
and a PDRLifetime of 0 indicates that the track should be
destroyed.
PDRSequence: 8-bit wrapping sequence number. The PDRSequence obeys
the operation in section 7.2 of [RPL]. It is incremented at each
PDR message and echoed in the PDR-ACK by the Root. The
PDRSequence is used to correlate a PDR-ACK message with the PDR
message that triggeted it.
5.2. New PDR-ACK Control Message
The new PDR-ACK is sent as a response to a PDR message with the 'K'
flag set. Its format is as follows:
Thubert, et al. Expires 12 November 2020 [Page 8]
Internet-Draft DAO Projection May 2020
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TrackID | PDR-ACK Status| Flags | Track Lifetime|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PDRSequence | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option(s)...
+-+-+-+-+-+-+-+
Figure 2: New PDR-ACK Control Message Format
TrackID: The RPLInstanceID of the Track that was created. Set to 0
when no Track is created.
PDR-ACK Status: Indicates the completion. Substructured as
indicated in Figure 3.
Track Lifetime: Indicates that remaining Lifetime for the Track, 0
if the Track was destroyed or not created.
PDRSequence: 8-bit wrapping sequence number. It is incremented at
each PDR message and echoed in the PDR-ACK.
The PDR-ACK Status is further substructured as follows:
0
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|E|R| Value |
+-+-+-+-+-+-+-+-+
Figure 3: PDR-ACK status Format
The PDR-ACK Status subfields are:
E: 1-bit flag. Set to indicate a rejection. When not set, a value
of 0 indicates Success/Unqualified acceptance and other values
indicate "not an outright rejection".
R: 1-bit flag. Reserved, MUST be set to 0 by the sender and ignored
by the receiver.
Status Value: 6-bit unsigned integer. Values depedning on the
setting of the 'E' flag as indicated respectively in Table 4 and
Table 5.
Thubert, et al. Expires 12 November 2020 [Page 9]
Internet-Draft DAO Projection May 2020
5.3. Route Projection Options
The RPOs indicate a series of IPv6 addresses that can be compressed
using the method defined in the "6LoWPAN Routing Header" [RFC8138]
specification using the address of the Root found in the DODAGID
field of DIO messages as Compression Reference.
An RPO indicates a Projected Route that can be a serial Track in full
or a segment of a more complex Track. In the latter case, multiple
RPO may be placed after a same Target Option. The Track is
identified by a TrackID that is a Local RPLInstanceID to the Target
of the Track.
The format of RPOs is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Option Length |Comp.| Flags | TrackID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Track Sequence| Track Lifetime| SegmentID |Segm. Sequence |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
. .
. Via Address 1 .
. .
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .... .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
. .
. Via Address n .
. .
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: Via Information option format
Option Type: 0x0A for VIO, 0x0B for SRVIO (to be confirmed by IANA)
Thubert, et al. Expires 12 November 2020 [Page 10]
Internet-Draft DAO Projection May 2020
Option Length: In bytes; variable, depending on the number of Via
Addresses.
Compression Type: 3-bit unsigned integer. This is the SRH-6LoRH
Type as defined in figure 7 in section 5.1 of [RFC8138] that
corresponds to the compression used for all the Via Addresses.
TrackID: 8-bit field indicating the topology Instance associated
with the Track. The tuple (Target Address, TrackID) forms a
unique ID of the Track in the RPL domain.
Track Sequence: 8-bit unsigned integer. The Track Sequence obeys
the operation in section 7.2 of [RPL] and the lollipop starts at
255. The Track Sequence is set by the Root and incremented each
time the Root refreshes that Track globally. A Track Sequence
that is fresher than the current on deprecates any state for the
Track. A Track Sequence that is current adds to any state that
was learned for that Track Sequence. A RTO with a Track Sequence
that is not as fresh as the current one is ignored.
Track Lifetime: 8-bit unsigned integer. The length of time in
Lifetime Units (obtained from the Configuration option) that the
Track is usable. The period starts when a new Track Sequence is
seen. A value of 255 (0xFF) represents infinity. A value of zero
(0x00) indicates a loss of reachability. A DAO message that
contains a Via Information option with a Path Lifetime of zero for
a Target is referred as a No-Path (for that Target) in this
document.
SegmentID: 8-bit field that identifies a segment within a Track. A
Value of 0 is used to signal a serial Track.
Segment Sequence: 8-bit unsigned integer. The Segment Sequence
obeys the operation in section 7.2 of [RPL] and the lollipop
starts at 255. When the Root of the DODAG needs to update a
single segment in a Track, but does not need to modify the rest of
the Track, it increments the Segment Sequence but not the Track
Sequence. The segment information indicated in the RTO deprecates
any state for the segment indicated by the SegmentID within the
indicated Track and sets up the new information. A RTO with a
Segment Sequence that is not as fresh as the current one is
ignored. a RTO for a given target with the same (TrackID, Track
Sequence, SegmentID, Segment Sequence) indicates a retry; it MUST
NOT change the segment and MUST be propagated or answered as the
first copy.
Thubert, et al. Expires 12 November 2020 [Page 11]
Internet-Draft DAO Projection May 2020
Via Address: 2 to 16 bytes, a compressed IPv6 Address. A Via
Address indicates the next hop within the path towards the
destination(s) that is indicated in the Target option that
immediately precede the RPO in the DAO message. Via Addresses are
indicated in the order of the path from the ingress to the egress
nodes. All Via addresses are expressed in the same size as
indicated by the Compression Type.
An RPO MUST contain at least one Via Address, and a Via Address MUST
NOT be present more than once, otherwise the RPO MUST be ignored.
5.4. Sibling Information Option
The Sibling Information Option (SIO) provides indication on siblings
that could be used by the Root to form Projected Routes. The format
of SIOs is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Option Length |Comp.|B|D|Flags| Opaque |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Step of Rank | Sibling Rank |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
. .
. Sibling DODAGID (if 'D' flag not set) .
. .
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
. .
. Sibling Address .
. .
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: Sibling Information Option Format
Option Type: 0x0C (to be confirmed by IANA)
Option Length: In bytes; variable, depending on the number of Via
Addresses.
Thubert, et al. Expires 12 November 2020 [Page 12]
Internet-Draft DAO Projection May 2020
Compression Type: 3-bit unsigned integer. This is the SRH-6LoRH
Type as defined in figure 7 in section 5.1 of [RFC8138] that
corresponds to the compression used for the Sibling Address.
Reserved for Flags: MUST be set to zero by the sender and MUST be
ignored by the receiver.
B: 1-bit flag that is set to indicate that the connectivity to the
sibling is bidirectional and roughly symmetrical. In that case,
only one of the siblings may report the SIO for the hop. If 'B'
is not set then the SIO only indicates connectivity from the
sibling to this node, and does not provide information on the hop
from this node to the sibling.
D: 1-bit flag that is set to indicate that sibling belongs to the
same DODAG. When not set, the Sibling DODAGID is indicated.
Opaque: MAY be used to carry information that the node and the Root
understand, e.g., a particular representation of the Link
properties such as a proprietary Link Quality Information for
packets received from the sibling. An industraial Alliance that
uses RPL for a particular use / environment MAY redefine the use
of this field to fit its needs.
Step of Rank: 16-bit unsigned integer. This is the Step of Rank
[RPL] as computed by the Objective Function between this node and
the sibling.
Sibling Rank: 16-bit unsigned integer. When non-zero, this is the
Rank [RPL] as exposed by the sibling in DIO messages.
Sibling DODAGID: 2 to 16 bytes, the DODAGID of the sibling in a
[RFC8138] compressed form as indicated by the Compression Type
field. This field is present when the 'D' flag is not set.
Sibling Address: 2 to 16 bytes, the IPv6 Address of the sibling in a
[RFC8138] compressed form as indicated by the Compression Type
field.
An SIO MAY be immediately followed by a DAG Metric Container. In
that case the DAG Metric Container provides additional metrics for
the hop from the Sibling to this node.
Thubert, et al. Expires 12 November 2020 [Page 13]
Internet-Draft DAO Projection May 2020
6. Projected DAO
This draft adds a capability to RPL whereby the Root of a DODAG
projects a route by sending an extended DAO message called one or
more Projected-DAO (P-DAO) messages to an arbitrary router in the
DODAG, indicating one or more sequence(s) of routers inside the DODAG
via which the Target(s) indicated in the RPL Target Option(s) (RTO)
can be reached.
A P-DAO is sent from a global address of the Root to a global address
of the recipient, and MUST be confirmed by a DAO-ACK, which is sent
back to a global address of the Root.
A P-DAO message MUST contain at least one RTO and at least one RPO
following it. There can be at most one such sequence of RTOs and
then RPOs.
Like a classical DAO message, a P-DAO causes a change of state only
if it is "new" per section 9.2.2. "Generation of DAO Messages" of
the RPL specification [RPL]; this is determined using the Track
Sequence and the Segment Sequence information from the RPO as opposed
to the Path Sequence from a TIO. Also, a Path Lifetime of 0 in an
RPO indicates that a route is to be removed.
There are two kinds of operation for the Projected Routes, the
Storing Mode and the Non-Storing Mode.
* The Non-Storing Mode is discussed in Section 6.1. It uses an
SRVIO that carries a list of Via Addresses to be used as a source-
routed path to the Target. The recipient of the P-DAO is the
ingress router of the source-routed path. Upon a Non-Storing Mode
P-DAO, the ingress router installs a source-routed state to the
Target and replies to the Root directly with a DAO-ACK message.
* The Storing Mode is discussed in Section 6.2. It uses a VIO with
one Via Address per consecutive hop, from the ingress to the
egress of the path, including the list of all intermediate routers
in the data path order. The Via Addresses indicate the routers in
which the routing state to the Target have to be installed via the
next Via Address in the VIO. In normal operations, the P-DAO is
propagated along the chain of Via Routers from the egress router
of the path till the ingress one, which confirms the installation
to the Root with a DAO-ACK message. Note that the Root may be the
ingress and it may be the egress of the path, that it can also be
neither but it cannot be both.
Thubert, et al. Expires 12 November 2020 [Page 14]
Internet-Draft DAO Projection May 2020
In case of a forwarding error along a Projected Route, an ICMP error
is sent to the Root with a new Code "Error in Projected Route" (See
Section 8.9). The Root can then modify or remove the Projected
Route. The "Error in Projected Route" message has the same format as
the "Destination Unreachable Message", as specified in RFC 4443
[RFC4443]. The portion of the invoking packet that is sent back in
the ICMP message SHOULD record at least up to the routing header if
one is present, and the routing header SHOULD be consumed by this
node so that the destination in the IPv6 header is the next hop that
this node could not reach. if a 6LoWPAN Routing Header (6LoRH)
[RFC8138] is used to carry the IPv6 routing information in the outter
header then that whole 6LoRH information SHOULD be present in the
ICMP message. The sender and exact operation depend on the Mode and
is described in Section 6.1 and Section 6.2 respectively.
6.1. Non-Storing Mode Projected Route
As illustrated in Figure 6, a P-DAO that carries an SRVIO enables the
Root to install a source-routed path towards a Target in any
particular router; with this path information the router can add a
source routed header reflecting the Projected Route to any packet for
which the current destination either is the said Target or can be
reached via the Target.
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+ | P ^ |
| | DAO | ACK | Loose
o o o o router V | | Source
o o o o o o o o o | P-DAO . Route
o o o o o o o o o o | Source . Path
o o o o o o o o o | Route . From
o o o o o o o o | Path . Root
o o o o o Target V . To
o o o o | Desti-
o o o o | nation
destination V
LLN
Figure 6: Projecting a Non-Storing Route
Thubert, et al. Expires 12 November 2020 [Page 15]
Internet-Draft DAO Projection May 2020
A route indicated by an SRVIO may be loose, meaning that the node
that owns the next listed Via Address is not necessarily a neighbor.
Without proper loop avoidance mechanisms, the interaction of loose
source routing and other mechanisms may effectively cause loops. In
order to avoid those loops, if the router that installs a Projected
Route does not have a connected route (a direct adjacency) to the
next soure routed hop and fails to locate it as a neighbor or a
neighbor of a neighbor, then it MUST ensure that it has another
Projected Route to the next loose hop under the control of the same
route computation system, otherwise the P-DAO is rejected.
When forwarding a packet to a destination for which the router
determines that routing happens via the Target, the router inserts
the source routing header in the packet to reach the Target. In
order to add a source-routing header, the router encapsulates the
packet with an IP-in-IP header and a non-storing mode source routing
header (SRH) [RFC6554]. In the uncompressed form the source of the
packet would be self, the destination would be the first Via Address
in the SRVIO, and the SRH would contain the list of the remaining Via
Addresses and then the Target.
In the case of a loose source-routed path, there MUST be either a
neighbor that is adjacent to the loose next hop, on which case the
packet is forwarded to that neighbor, or a source-routed path to the
loose next hop; in the latter case, another encapsulation takes place
and the process possibly recurses; otherwise the packet is dropped.
In practice, the router will normally use the "IPv6 over Low-Power
Wireless Personal Area Network (6LoWPAN) Paging Dispatch" [RFC8025]
to compress the RPL artifacts as indicated in [RFC8138]. In that
case, the router indicates self as encapsulator in an IP-in-IP 6LoRH
Header, and places the list of Via Addresses in the order of the VIO
and then the Target in the SRH 6LoRH Header.
In case of a forwarding error along a Source Route path, the node
that fails to forward SHOULD send an ICMP error with a code "Error in
Source Routing Header" back to the source of the packet, as described
in section 11.2.2.3. of [RPL]. Upon this message, the encapsulating
node SHOULD stop using the source route path for a period of time and
it SHOULD send an ICMP message with a Code "Error in Projected Route"
to the Root. Failure to follow these steps may result in packet loss
and wasted resources along the source route path that is broken.
Thubert, et al. Expires 12 November 2020 [Page 16]
Internet-Draft DAO Projection May 2020
6.2. Storing-Mode Projected Route
As illustrated in Figure 7, the Storing Mode route projection is used
by the Root to install a routing state towards a Target in the
routers along a segment between an ingress and an egress router; this
enables the routers to forward along that segment any packet for
which the next loose hop is the said Target, for Instance a loose
source routed packet for which the next loose hop is the Target, or a
packet for which the router has a routing state to the final
destination via the Target.
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+ | ^ |
| | DAO | ACK |
o o o o | | |
o o o o o o o o o | ^ | Projected .
o o o o o o o o o o | | DAO | Route .
o o o o o o o o o | ^ | .
o o o o o o o o v | DAO v .
o o LLN o o o |
o o o o o Loose Source Route Path |
o o o o From Root To Destination v
Figure 7: Projecting a route
In order to install the relevant routing state along the segment
between an ingress and an egress routers, the Root sends a unicast
P-DAO message to the egress router of the routing segment that must
be installed. The P-DAO message contains the ordered list of hops
along the segment as a direct sequence of Via Information options
that are preceded by one or more RPL Target options to which they
relate. Each Via Information option contains a Path Lifetime for
which the state is to be maintained.
The Root sends the P-DAO directly to the egress node of the segment.
In that P-DAO, the destination IP address matches the Via Address in
the last VIO. This is how the egress recognizes its role. In a
similar fashion, the ingress node recognizes its role as it matches
Via Address in the first VIO.
The egress node of the segment is the only node in the path that does
not install a route in response to the P-DAO; it is expected to be
already able to route to the Target(s) on its own. It may either be
Thubert, et al. Expires 12 November 2020 [Page 17]
Internet-Draft DAO Projection May 2020
the Target, or may have some existing information to reach the
Target(s), such as a connected route or an already installed
Projected Route. If one of the Targets cannot be located, the node
MUST answer to the Root with a negative DAO-ACK listing the Target(s)
that could not be located (suggested status 10 to be confirmed by
IANA).
If the egress node can reach all the Targets, then it forwards the
P-DAO with unchanged content to its loose predecessor in the segment
as indicated in the list of Via Information options, and recursively
the message is propagated unchanged along the sequence of routers
indicated in the P-DAO, but in the reverse order, from egress to
ingress.
The address of the predecessor to be used as destination of the
propagated DAO message is found in the Via Information option the
precedes the one that contain the address of the propagating node,
which is used as source of the packet.
Upon receiving a propagated DAO, an intermediate router as well as
the ingress router install a route towards the DAO Target(s) via its
successor in the P-DAO; the router locates the VIO that contains its
address, and uses as next hop the address found in the Via Address
field in the following VIO. The router MAY install additional routes
towards the addresses that are located in VIOs that are after the
next one, if any, but in case of a conflict or a lack of resource, a
route to a Target installed by the Root has precedence.
The process recurses till the P-DAO is propagated to ingress router
of the segment, which answers with a DAO-ACK to the Root.
Also, the path indicated in a P-DAO may be loose, in which case the
reachability to the next hop has to be asserted. Each router along
the path indicated in a P-DAO is expected to be able to reach its
successor, either with a connected route (direct neighbor), or by
routing, for Instance following a route installed previously by a DAO
or a P-DAO message. If that route is not connected then a recursive
lookup may take place at packet forwarding time to find the next hop
to reach the Target(s). If it does not and cannot reach the next
router in the P-DAO, the router MUST answer to the Root with a
negative DAO-ACK indicating the successor that is unreachable
(suggested status 11 to be confirmed by IANA).
A Path Lifetime of 0 in a Via Information option is used to clean up
the state. The P-DAO is forwarded as described above, but the DAO is
interpreted as a No-Path DAO and results in cleaning up existing
state as opposed to refreshing an existing one or installing a new
one.
Thubert, et al. Expires 12 November 2020 [Page 18]
Internet-Draft DAO Projection May 2020
In case of a forwarding error along a Storing Mode Projected Route,
the node that fails to forward SHOULD send an ICMP error with a code
"Error in Projected Route" to the Root. Failure to do so may result
in packet loss and wasted resources along the Projected Route that is
broken.
7. Security Considerations
This draft uses messages that are already present in RPL [RPL] with
optional secured versions. The same secured versions may be used
with this draft, and whatever security is deployed for a given
network also applies to the flows in this draft.
TODO: should probably consider how P-DAO messages could be abused by
a) rogue nodes b) via replay of messages c) if use of P-DAO messages
could in fact deal with any threats?
8. IANA Considerations
8.1. New RPL Control Codes
This document extends the IANA Subregistry created by RFC 6550 for
RPL Control Codes as indicated in Table 1:
+------+-----------------------------+---------------+
| Code | Description | Reference |
+======+=============================+===============+
| 0x09 | Projected DAO Request (PDR) | This document |
+------+-----------------------------+---------------+
| 0x0A | PDR-ACK | This document |
+------+-----------------------------+---------------+
Table 1: New RPL Control Codes
8.2. New RPL Control Message Options
This document extends the IANA Subregistry created by RFC 6550 for
RPL Control Message Options as indicated in Table 2:
Thubert, et al. Expires 12 November 2020 [Page 19]
Internet-Draft DAO Projection May 2020
+-------+--------------------------------------+---------------+
| Value | Meaning | Reference |
+=======+======================================+===============+
| 0x0B | Via Information option | This document |
+-------+--------------------------------------+---------------+
| 0x0C | Source-Routed Via Information option | This document |
+-------+--------------------------------------+---------------+
| 0x0D | Sibling Information option | This document |
+-------+--------------------------------------+---------------+
Table 2: RPL Control Message Options
8.3. New SubRegistry for the Projected DAO Request (PDR) Flags
IANA is required to create a registry for the 8-bit Projected DAO
Request (PDR) Flags field. Each bit is tracked with the following
qualities:
* Bit number (counting from bit 0 as the most significant bit)
* Capability description
* Reference
Registration procedure is "Standards Action" [RFC8126]. The initial
allocation is as indicated in Table 3:
+------------+------------------------+---------------+
| Bit number | Capability description | Reference |
+============+========================+===============+
| 0 | PDR-ACK request (K) | This document |
+------------+------------------------+---------------+
| 1 | Requested path should | This document |
| | be redundant (R) | |
+------------+------------------------+---------------+
Table 3: Initial PDR Flags
8.4. New SubRegistry for the PDR-ACK Flags
IANA is required to create an subregistry for the 8-bit PDR-ACK Flags
field. Each bit is tracked with the following qualities:
* Bit number (counting from bit 0 as the most significant bit)
* Capability description
* Reference
Thubert, et al. Expires 12 November 2020 [Page 20]
Internet-Draft DAO Projection May 2020
Registration procedure is "Standards Action" [RFC8126]. No bit is
currently defined for the PDR-ACK Flags.
8.5. New Subregistry for the PDR-ACK Acceptance Status values
IANA is requested to create a new subregistry for the PDR-ACK
Acceptance Status values.
* Possible values are 6-bit unsigned integers (0..63).
* Registration procedure is "Standards Action" [RFC8126].
* Initial allocation is as indicated in Table 4:
+-------+------------------------+---------------+
| Value | Meaning | Reference |
+=======+========================+===============+
| 0 | Unqualified acceptance | This document |
+-------+------------------------+---------------+
Table 4: Acceptance values of the PDR-ACK Status
8.6. New Subregistry for the PDR-ACK Rejection Status values
IANA is requested to create a new subregistry for the PDR-ACK
Rejection Status values.
* Possible values are 6-bit unsigned integers (0..63).
* Registration procedure is "Standards Action" [RFC8126].
* Initial allocation is as indicated in Table 5:
+-------+-----------------------+---------------+
| Value | Meaning | Reference |
+=======+=======================+===============+
| 0 | Unqualified rejection | This document |
+-------+-----------------------+---------------+
Table 5: Rejection values of the PDR-ACK Status
8.7. New SubRegistry for the Route Projection Options (RPO) Flags
IANA is requested to create a new subregistry for the 5-bit Route
Projection Options (RPO) Flags field. Each bit is tracked with the
following qualities:
* Bit number (counting from bit 0 as the most significant bit)
Thubert, et al. Expires 12 November 2020 [Page 21]
Internet-Draft DAO Projection May 2020
* Capability description
* Reference
Registration procedure is "Standards Action" [RFC8126]. No bit is
currently defined for the Route Projection Options (RPO) Flags.
8.8. New SubRegistry for the Sibling Information Option (SIO) Flags
IANA is required to create a registry for the 5-bit Sibling
Information Option (SIO) Flags field. Each bit is tracked with the
following qualities:
* Bit number (counting from bit 0 as the most significant bit)
* Capability description
* Reference
Registration procedure is "Standards Action" [RFC8126]. The initial
allocation is as indicated in Table 6:
+------------+-----------------------------------+---------------+
| Bit number | Capability description | Reference |
+============+===================================+===============+
| 0 | Connectivity is bidirectional (B) | This document |
+------------+-----------------------------------+---------------+
Table 6: Initial SIO Flags
8.9. Error in Projected Route ICMPv6 Code
In some cases RPL will return an ICMPv6 error message when a message
cannot be forwarded along a Projected Route. This ICMPv6 error
message is "Error in Projected Route".
IANA has defined an ICMPv6 "Code" Fields Registry for ICMPv6 Message
Types. ICMPv6 Message Type 1 describes "Destination Unreachable"
codes. This specification requires that a new code is allocated from
the ICMPv6 Code Fields Registry for ICMPv6 Message Type 1, for "Error
in Projected Route", with a suggested code value of 8, to be
confirmed by IANA.
9. Acknowledgments
The authors wish to acknowledge JP Vasseur, Remy Liubing, James
Pylakutty and Patrick Wetterwald for their contributions to the ideas
developed here.
Thubert, et al. Expires 12 November 2020 [Page 22]
Internet-Draft DAO Projection May 2020
10. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", STD 89,
RFC 4443, DOI 10.17487/RFC4443, March 2006,
<https://www.rfc-editor.org/info/rfc4443>.
[RPL] Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
Low-Power and Lossy Networks", RFC 6550,
DOI 10.17487/RFC6550, March 2012,
<https://www.rfc-editor.org/info/rfc6550>.
[RFC6554] Hui, J., Vasseur, JP., Culler, D., and V. Manral, "An IPv6
Routing Header for Source Routes with the Routing Protocol
for Low-Power and Lossy Networks (RPL)", RFC 6554,
DOI 10.17487/RFC6554, March 2012,
<https://www.rfc-editor.org/info/rfc6554>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
11. Informative References
[RFC7102] Vasseur, JP., "Terms Used in Routing for Low-Power and
Lossy Networks", RFC 7102, DOI 10.17487/RFC7102, January
2014, <https://www.rfc-editor.org/info/rfc7102>.
[RFC6997] Goyal, M., Ed., Baccelli, E., Philipp, M., Brandt, A., and
J. Martocci, "Reactive Discovery of Point-to-Point Routes
in Low-Power and Lossy Networks", RFC 6997,
DOI 10.17487/RFC6997, August 2013,
<https://www.rfc-editor.org/info/rfc6997>.
Thubert, et al. Expires 12 November 2020 [Page 23]
Internet-Draft DAO Projection May 2020
[6TiSCH-ARCHI]
Thubert, P., "An Architecture for IPv6 over the TSCH mode
of IEEE 802.15.4", Work in Progress, Internet-Draft,
draft-ietf-6tisch-architecture-28, 29 October 2019,
<https://tools.ietf.org/html/draft-ietf-6tisch-
architecture-28>.
[RAW-ARCHI]
Thubert, P. and G. Papadopoulos, "Reliable and Available
Wireless Architecture/Framework", Work in Progress,
Internet-Draft, draft-pthubert-raw-architecture-01, 2
April 2020, <https://tools.ietf.org/html/draft-pthubert-
raw-architecture-01>.
[TURN-ON_RFC8138]
Thubert, P. and L. Zhao, "Configuration option for RFC
8138", Work in Progress, Internet-Draft, draft-thubert-
roll-turnon-rfc8138-03, 8 July 2019,
<https://tools.ietf.org/html/draft-thubert-roll-turnon-
rfc8138-03>.
[RFC8655] Finn, N., Thubert, P., Varga, B., and J. Farkas,
"Deterministic Networking Architecture", RFC 8655,
DOI 10.17487/RFC8655, October 2019,
<https://www.rfc-editor.org/info/rfc8655>.
[RFC8025] Thubert, P., Ed. and R. Cragie, "IPv6 over Low-Power
Wireless Personal Area Network (6LoWPAN) Paging Dispatch",
RFC 8025, DOI 10.17487/RFC8025, November 2016,
<https://www.rfc-editor.org/info/rfc8025>.
[RFC8138] Thubert, P., Ed., Bormann, C., Toutain, L., and R. Cragie,
"IPv6 over Low-Power Wireless Personal Area Network
(6LoWPAN) Routing Header", RFC 8138, DOI 10.17487/RFC8138,
April 2017, <https://www.rfc-editor.org/info/rfc8138>.
[PCE] IETF, "Path Computation Element",
<https://datatracker.ietf.org/doc/charter-ietf-pce/>.
Appendix A. Applications
Thubert, et al. Expires 12 November 2020 [Page 24]
Internet-Draft DAO Projection May 2020
A.1. Loose Source Routing in Non-storing Mode
A RPL implementation operating in a very constrained LLN typically
uses the Non-Storing Mode of Operation as represented in Figure 8.
In that mode, a RPL node indicates a parent-child relationship to the
Root, using a Destination Advertisement Object (DAO) that is unicast
from the node directly to the Root, and the Root typically builds a
source routed path to a destination down the DODAG by recursively
concatenating this information.
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+ ^ | |
| | DAO | ACK |
o o o o | | | Strict
o o o o o o o o o | | | Source
o o o o o o o o o o | | | Route
o o o o o o o o o | | |
o o o o o o o o | v v
o o o o
LLN
Figure 8: RPL non-storing mode of operation
Based on the parent-children relationships expressed in the non-
storing DAO messages,the Root possesses topological information about
the whole network, though this information is limited to the
structure of the DODAG for which it is the destination. A packet
that is generated within the domain will always reach the Root, which
can then apply a source routing information to reach the destination
if the destination is also in the DODAG. Similarly, a packet coming
from the outside of the domain for a destination that is expected to
be in a RPL domain reaches the Root.
It results that the Root, or then some associated centralized
computation engine such as a PCE, can determine the amount of packets
that reach a destination in the RPL domain, and thus the amount of
energy and bandwidth that is wasted for transmission, between itself
and the destination, as well as the risk of fragmentation, any
potential delays because of a paths longer than necessary (shorter
paths exist that would not traverse the Root).
Thubert, et al. Expires 12 November 2020 [Page 25]
Internet-Draft DAO Projection May 2020
As a network gets deep, the size of the source routing header that
the Root must add to all the downward packets becomes an issue for
nodes that are many hops away. In some use cases, a RPL network
forms long lines and a limited amount of well-Targeted routing state
would allow to make the source routing operation loose as opposed to
strict, and save packet size. Limiting the packet size is directly
beneficial to the energy budget, but, mostly, it reduces the chances
of frame loss and/or packet fragmentation, which is highly
detrimental to the LLN operation. Because the capability to store a
routing state in every node is limited, the decision of which route
is installed where can only be optimized with a global knowledge of
the system, a knowledge that the Root or an associated PCE may
possess by means that are outside of the scope of this specification.
This specification enables to store source-routed or storing mode
state in intermediate routers, which enables to limit the excursion
of the source route headers in deep networks. Once a P-DAO exchange
has taken place for a given Target, if the Root operates in non
storing mode, then it may elide the sequence of routers that is
installed in the network from its source route headers to destination
that are reachable via that Target, and the source route headers
effectively become loose.
A.2. Transversal Routes in storing and non-storing modes
RPL is optimized for Point-to-Multipoint (P2MP) and Multipoint-to-
Point (MP2P), whereby routes are always installed along the RPL DODAG
respectively from and towards the DODAG Root. Transversal Peer to
Peer (P2P) routes in a RPL network will generally suffer from some
elongated (stretched) path versus the best possible path, since
routing between 2 nodes always happens via a common parent, as
illustrated in Figure 9:
* in non-storing mode, all packets routed within the DODAG flow all
the way up to the Root of the DODAG. If the destination is in the
same DODAG, the Root must encapsulate the packet to place a
Routing Header that has the strict source route information down
the DODAG to the destination. This will be the case even if the
destination is relatively close to the source and the Root is
relatively far off.
Thubert, et al. Expires 12 November 2020 [Page 26]
Internet-Draft DAO Projection May 2020
* In storing mode, unless the destination is a child of the source,
the packets will follow the default route up the DODAG as well.
If the destination is in the same DODAG, they will eventually
reach a common parent that has a route to the destination; at
worse, the common parent may also be the Root. From that common
parent, the packet will follow a path down the DODAG that is
optimized for the Objective Function that was used to build the
DODAG.
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+
X
^ v o o
^ o o v o o o o o
^ o o o v o o o o o
^ o o v o o o o o
S o o o D o o o
o o o o
LLN
Figure 9: Routing Stretch between S and D via common parent X
It results that it is often beneficial to enable transversal P2P
routes, either if the RPL route presents a stretch from shortest
path, or if the new route is engineered with a different objective.
For that reason, earlier work at the IETF introduced the "Reactive
Discovery of Point-to-Point Routes in Low Power and Lossy Networks"
[RFC6997], which specifies a distributed method for establishing
optimized P2P routes. This draft proposes an alternate based on a
centralized route computation.
Thubert, et al. Expires 12 November 2020 [Page 27]
Internet-Draft DAO Projection May 2020
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+
|
o o o o
o o o o o o o o o
o o o o o o o o o o
o o o o o o o o o
S>>A>>>B>>C>>>D o o o
o o o o
LLN
Figure 10: Projected Transversal Route
This specification enables to store source-routed or storing mode
state in intermediate routers, which enables to limit the stretch of
a P2P route and maintain the characteristics within a given SLA. An
example of service using this mechanism oculd be a control loop that
would be installed in a network that uses classical RPL for
asynchronous data collection. In that case, the P2P path may be
installed in a different RPL Instance, with a different objective
function.
Appendix B. Examples
B.1. Using storing mode P-DAO in non-storing mode MOP
In non-storing mode, the DAG Root maintains the knowledge of the
whole DODAG topology, so when both the source and the destination of
a packet are in the DODAG, the Root can determine the common parent
that would have been used in storing mode, and thus the list of nodes
in the path between the common parent and the destination. For
Instance in the diagram shown in Figure 11, if the source is node 41
and the destination is node 52, then the common parent is node 22.
Thubert, et al. Expires 12 November 2020 [Page 28]
Internet-Draft DAO Projection May 2020
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+
| \ \____
/ \ \
o 11 o 12 o 13
/ | / \
o 22 o 23 o 24 o 25
/ \ | \ \
o 31 o 32 o o o 35
/ / | \ | \
o 41 o 42 o o o 45 o 46
| | | | \ |
o 51 o 52 o 53 o o 55 o 56
LLN
Figure 11: Example DODAG forming a logical tree topology
With this draft, the Root can install a storing mode routing states
along a segment that is either from itself to the destination, or
from one or more common parents for a particular source/destination
pair towards that destination (in this particular example, this would
be the segment made of nodes 22, 32, 42).
In the example below, say that there is a lot of traffic to nodes 55
and 56 and the Root decides to reduce the size of routing headers to
those destinations. The Root can first send a DAO to node 45
indicating Target 55 and a Via segment (35, 45), as well as another
DAO to node 46 indicating Target 56 and a Via segment (35, 46). This
will save one entry in the routing header on both sides. The Root
may then send a DAO to node 35 indicating Targets 55 and 56 a Via
segment (13, 24, 35) to fully optimize that path.
Alternatively, the Root may send a DAO to node 45 indicating Target
55 and a Via segment (13, 24, 35, 45) and then a DAO to node 46
indicating Target 56 and a Via segment (13, 24, 35, 46), indicating
the same DAO Sequence.
B.2. Projecting a storing-mode transversal route
In this example, say that a PCE determines that a path must be
installed between node S and node D via routers A, B and C, in order
to serve the needs of a particular application.
Thubert, et al. Expires 12 November 2020 [Page 29]
Internet-Draft DAO Projection May 2020
The Root sends a P-DAO with a Target option indicating the
destination D and a sequence Via Information option, one for S, which
is the ingress router of the segment, one for A and then for B, which
are an intermediate routers, and one for C, which is the egress
router.
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+
| P-DAO message to C
o | o o
o o o | o o o o o
o o o | o o o o o o
o o V o o o o o o
S A B C D o o o
o o o o
LLN
Figure 12: P-DAO from Root
Upon reception of the P-DAO, C validates that it can reach D, e.g.
using IPv6 Neighbor Discovery, and if so, propagates the P-DAO
unchanged to B.
B checks that it can reach C and of so, installs a route towards D
via C. Then it propagates the P-DAO to A.
The process recurses till the P-DAO reaches S, the ingress of the
segment, which installs a route to D via A and sends a DAO-ACK to the
Root.
Thubert, et al. Expires 12 November 2020 [Page 30]
Internet-Draft DAO Projection May 2020
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+
^ P-DAO-ACK from S
/ o o o
/ o o o o o o o
| o o o o o o o o o
| o o o o o o o o
S A B C D o o o
o o o o
LLN
Figure 13: P-DAO-ACK to Root
As a result, a transversal route is installed that does not need to
follow the DODAG structure.
------+---------
| Internet
|
+-----+
| | Border Router
| | (RPL Root)
+-----+
|
o o o o
o o o o o o o o o
o o o o o o o o o o
o o o o o o o o o
S>>A>>>B>>C>>>D o o o
o o o o
LLN
Figure 14: Projected Transversal Route
Authors' Addresses
Pascal Thubert (editor)
Cisco Systems, Inc
Building D
45 Allee des Ormes - BP1200
06254 Mougins - Sophia Antipolis
France
Thubert, et al. Expires 12 November 2020 [Page 31]
Internet-Draft DAO Projection May 2020
Phone: +33 497 23 26 34
Email: pthubert@cisco.com
Rahul Arvind Jadhav
Huawei Tech
Kundalahalli Village, Whitefield,
Bangalore 560037
Karnataka
India
Phone: +91-080-49160700
Email: rahul.ietf@gmail.com
Matthew Gillmore
Itron, Inc
Building D
2111 N Molter Road
Liberty Lake, 99019
United States
Phone: +1.800.635.5461
Email: matthew.gillmore@itron.com
Thubert, et al. Expires 12 November 2020 [Page 32]