roll                                                     P. Thubert, Ed.
Internet-Draft                                                     Cisco
Intended status: Standards Track                              C. Bormann
Expires: April 30, 2017                                   Uni Bremen TZI
                                                              L. Toutain
                                                    IMT-TELECOM Bretagne
                                                               R. Cragie
                                                                     ARM
                                                        October 27, 2016


                         6LoWPAN Routing Header
                  draft-ietf-roll-routing-dispatch-05

Abstract

   This specification introduces a new 6LoWPAN dispatch type for use in
   6LoWPAN Route-Over topologies, that initially covers the needs of RPL
   (RFC6550) data packets compression.  Using this dispatch type, this
   specification defines a method to compress RPL Option (RFC6553)
   information and Routing Header type 3 (RFC6554), an efficient IP-in-
   IP technique and is extensible for more applications.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 30, 2017.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of



Thubert, et al.          Expires April 30, 2017                 [Page 1]


Internet-Draft           6LoWPAN Routing Header             October 2016


   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   6
   3.  Using the Page Dispatch . . . . . . . . . . . . . . . . . . .   6
     3.1.  New Routing Header Dispatch (6LoRH) . . . . . . . . . . .   6
     3.2.  Placement Of 6LoRH headers  . . . . . . . . . . . . . . .   7
       3.2.1.  Relative To Non-6LoRH Headers . . . . . . . . . . . .   7
       3.2.2.  Relative To Other 6LoRH Headers . . . . . . . . . . .   7
   4.  6LoWPAN Routing Header General Format . . . . . . . . . . . .   8
     4.1.  Elective Format . . . . . . . . . . . . . . . . . . . . .   9
     4.2.  Critical Format . . . . . . . . . . . . . . . . . . . . .   9
     4.3.  Compressing Addresses . . . . . . . . . . . . . . . . . .  10
       4.3.1.  Coalescence . . . . . . . . . . . . . . . . . . . . .  10
       4.3.2.  DODAG Root Address Determination  . . . . . . . . . .  11
   5.  The SRH 6LoRH Header  . . . . . . . . . . . . . . . . . . . .  12
     5.1.  Encoding  . . . . . . . . . . . . . . . . . . . . . . . .  12
     5.2.  SRH-6LoRH General Operation . . . . . . . . . . . . . . .  13
       5.2.1.  Uncompressed SRH Operation  . . . . . . . . . . . . .  13
       5.2.2.  6LoRH-Compressed SRH Operation  . . . . . . . . . . .  14
       5.2.3.  Inner LOWPAN_IPHC Compression . . . . . . . . . . . .  14
     5.3.  The Design Point of Popping Entries . . . . . . . . . . .  15
     5.4.  Compression Reference for SRH-6LoRH header entries  . . .  16
     5.5.  Popping Headers . . . . . . . . . . . . . . . . . . . . .  17
     5.6.  Forwarding  . . . . . . . . . . . . . . . . . . . . . . .  17
   6.  The RPL Packet Information 6LoRH  . . . . . . . . . . . . . .  18
     6.1.  Compressing the RPLInstanceID . . . . . . . . . . . . . .  19
     6.2.  Compressing the SenderRank  . . . . . . . . . . . . . . .  20
     6.3.  The Overall RPI-6LoRH encoding  . . . . . . . . . . . . .  20
   7.  The IP-in-IP 6LoRH Header . . . . . . . . . . . . . . . . . .  23
   8.  Management Considerations . . . . . . . . . . . . . . . . . .  24
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .  25
   10. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  26
     10.1.  Reserving Space in 6LoWPAN Dispatch Page 1 . . . . . . .  26
     10.2.  New Critical 6LoWPAN Routing Header Type Registry  . . .  26
     10.3.  New Elective 6LoWPAN Routing Header Type Registry  . . .  26
   11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  27
   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  27
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  27
     12.2.  Informative References . . . . . . . . . . . . . . . . .  28
   Appendix A.  Examples . . . . . . . . . . . . . . . . . . . . . .  29



Thubert, et al.          Expires April 30, 2017                 [Page 2]


Internet-Draft           6LoWPAN Routing Header             October 2016


     A.1.  Examples Compressing The RPI  . . . . . . . . . . . . . .  29
     A.2.  Example Of Downward Packet In Non-Storing Mode  . . . . .  31
     A.3.  Example of SRH-6LoRH life-cycle . . . . . . . . . . . . .  33
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  35

1.  Introduction

   The design of Low Power and Lossy Networks (LLNs) is generally
   focused on saving energy, a very constrained resource in most cases.
   The other constraints, such as the memory capacity and the duty
   cycling of the LLN devices, derive from that primary concern.  Energy
   is often available from primary batteries that are expected to last
   for years, or is scavenged from the environment in very limited
   quantities.  Any protocol that is intended for use in LLNs must be
   designed with the primary concern of saving energy as a strict
   requirement.

   Controlling the amount of data transmission is one possible venue to
   save energy.  In a number of LLN standards, the frame size is limited
   to much smaller values than the guaranteed IPv6 maximum transmission
   unit (MTU) of 1280 bytes.  In particular, an LLN that relies on the
   classical Physical Layer (PHY) of IEEE 802.15.4 [IEEE802154] is
   limited to 127 bytes per frame.  The need to compress IPv6 packets
   over IEEE 802.15.4 led to the "6LoWPAN Header Compression" [RFC6282]
   work (6LoWPAN_HC).

   Innovative Route-over techniques have been and are still being
   developed for routing inside a LLN.  In a general fashion, such
   techniques require additional information in the packet to provide
   loop prevention and to indicate information such as flow
   identification, source routing information, etc.

   For reasons such as security and the capability to send ICMPv6 errors
   (see "Internet Control Message Protocol (ICMPv6)" [RFC4443]) back to
   the source, an original packet must not be tampered with, and any
   information that must be inserted in or removed from an IPv6 packet
   must be placed in an extra IP-in-IP encapsulation.

   This is the case when the additional routing information is inserted
   by a router on the path of a packet, for instance the root of a mesh,
   as opposed to the source node, with the non-storing mode of the "IPv6
   Routing Protocol for Low-Power and Lossy Networks" [RFC6550] (RPL).

   This is also the case when some routing information must be removed
   from a packet that flows outside the LLN.

   "When to use RFC 6553, RFC 6554 and IPv6-in-IPv6"
   [I-D.ietf-roll-useofrplinfo] details different cases where IPv6



Thubert, et al.          Expires April 30, 2017                 [Page 3]


Internet-Draft           6LoWPAN Routing Header             October 2016


   headers defined in the "RPL Option for Carrying RPL Information in
   Data-Plane Datagrams" [RFC6553] and the "Routing Header for Source
   Routes with RPL" [RFC6554], and IPv6-in-IPv6 encapsulation, are
   inserted or removed from packets in a LLN environments operating RPL.

   When using RFC 6282 [RFC6282] the outer IP header of an IP-in-IP
   encapsulation may be compressed down to 2 octets in stateless
   compression and down to 3 octets in stateful compression when context
   information must be added.

      0                                       1
      0   1   2   3   4   5   6   7   8   9   0   1   2   3   4   5
    +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
    | 0 | 1 | 1 |  TF   |NH | HLIM  |CID|SAC|  SAM  | M |DAC|  DAM  |
    +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+

              Figure 1: LOWPAN_IPHC base Encoding (RFC6282).

   The Stateless Compression of an IPv6 addresses can only happen if the
   IPv6 address can de deduced from the MAC addresses, meaning that the
   IP end point is also the MAC-layer endpoint.  This is generally not
   the case in a RPL network which is generally a multi-hop route-over
   (i.e., operated at Layer-3) network.  A better compression, which
   does not involve variable compressions depending on the hop in the
   mesh, can be achieved based on the fact that the outer encapsulation
   is usually between the source (or destination) of the inner packet
   and the root.  Also, the inner IP header can only be compressed by
   RFC 6282 [RFC6282] if all the fields preceding it are also
   compressed.  This specification makes the inner IP header the first
   header to be compressed by RFC 6282 [RFC6282], and keeps the inner
   packet encoded the same way whether it is encapsulated or not, thus
   preserving existing implementations.

   As an example, RPL [RFC6550] is designed to optimize the routing
   operations in constrained LLNs.  As part of this optimization, RPL
   requires the addition of RPL Packet Information (RPI) in every
   packet, as defined in Section 11.2 of RFC 6550 [RFC6550].

   The "RPL Option for Carrying RPL Information in Data-Plane Datagrams"
   [RFC6553] specification indicates how the RPI can be placed in a RPL
   Option (RPL-OPT) that is placed in an IPv6 Hop-by-Hop header.

   This representation demands a total of 8 bytes, while in most cases
   the actual RPI payload requires only 19 bits.  Since the Hop-by-Hop
   header must not flow outside of the RPL domain, it must be inserted
   in packets entering the domain and be removed from packets that leave
   the domain.  In both cases, this operation implies an IP-in-IP
   encapsulation.



Thubert, et al.          Expires April 30, 2017                 [Page 4]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Additionally, in the case of the Non-Storing Mode of Operation (MOP),
   RPL requires a Source Routing Header (SRH) in all packets that are
   routed down a RPL graph. for that purpose, the "IPv6 Routing Header
   for Source Routes with RPL" [RFC6554] specification defines the type
   3 Routing Header for IPv6 (RH3).

          ------+---------                           ^
                |          Internet                  |
                |                                    | Native IPv6
             +-----+                                 |
             |     | Border Router (RPL Root)      + | +
             |     |                               | | |
             +-----+                               | | | tunneled
                |                                  | | | using
          o    o   o    o                          | | | IPv6-in-
      o o   o  o   o  o  o o   o                   | | | IPv6 and
     o  o o  o o    o   o   o  o  o                | | | RPL SRH
     o   o    o  o     o  o    o  o  o             | | |
    o  o   o  o   o         o   o o                | | |
    o          o             o     o               + v +
                      LLN


             Figure 2: IP-in-IP Encapsulation within the LLN.

   With Non-Storing RPL, even if the source is a node in the same LLN,
   the packet must first reach up the graph to the root so that the root
   can insert the SRH to go down the graph.  In any fashion, whether the
   packet was originated in a node in the LLN or outside the LLN, and
   regardless of whether the packet stays within the LLN or not, as long
   as the source of the packet is not the root itself, the source-
   routing operation also implies an IP-in-IP encapsulation at the root
   in order to insert the SRH.

   "The 6TiSCH Architecture" [I-D.ietf-6tisch-architecture] specifies
   the operation of IPv6 over the "TimeSlotted Channel Hopping"
   [RFC7554] (TSCH) mode of operation of IEEE 802.15.4.  The
   architecture requires the use of both RPL and the 6lo adaptation
   layer over IEEE 802.15.4.  Because it inherits the constraints on
   frame size from the MAC layer, 6TiSCH cannot afford to allocate 8
   bytes per packet on the RPI.  Hence the requirement for 6LoWPAN
   header compression of the RPI.

   An extensible compression technique is required that simplifies IP-
   in-IP encapsulation when it is needed, and optimally compresses
   existing routing artifacts found in RPL LLNs.





Thubert, et al.          Expires April 30, 2017                 [Page 5]


Internet-Draft           6LoWPAN Routing Header             October 2016


   This specification extends the 6lo adaptation layer framework (RFC
   4944 [RFC4944] and RFC 6282 [RFC6282]) so as to carry routing
   information for route-over networks based on RPL.  The specification
   includes the formats necessary for RPL and is extensible for
   additional formats.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in RFC
   2119 [RFC2119].

   The Terminology used in this document is consistent with and
   incorporates that described in Terminology in Low power And Lossy
   Networks [RFC7102] and RPL [RFC6550].

   The terms Route-over and Mesh-under are defined in RFC 6775
   [RFC6775].

   Other terms in use in LLNs are found in "Terminology for Constrained-
   Node Networks" [RFC7228].

   The term "byte" is used in its now customary sense as a synonym for
   "octet".

3.  Using the Page Dispatch

   The 6LoWPAN Paging Dispatch [I-D.ietf-6lo-paging-dispatch]
   specification extends the 6lo adaptation layer framework (RFC 4944
   [RFC4944] and RFC 6282 [RFC6282]) by introducing a concept of
   "context" in the 6LoWPAN parser, a context being identified by a Page
   number.  The specification defines 16 Pages.

   This draft operates within Page 1, which is indicated by a Dispatch
   Value of binary 11110001.

3.1.  New Routing Header Dispatch (6LoRH)

   This specification introduces a new 6LoWPAN Routing Header (6LoRH) to
   carry IPv6 routing information.  The 6LoRH may contain source routing
   information such as a compressed form of SRH, as well as other sorts
   of routing information such as the RPI and IP-in-IP encapsulation.

   The 6LoRH is expressed in a 6loWPAN packet as a Type-Length-Value
   (TLV) field, which is extensible for future use.





Thubert, et al.          Expires April 30, 2017                 [Page 6]


Internet-Draft           6LoWPAN Routing Header             October 2016


   It is expected that a router that does not recognize the 6LoRH
   general format detailed in Section 4 will drop the packet when a
   6LoRH is present.

   This specification uses the bit pattern 10xxxxxx in Page 1 for the
   new 6LoRH Dispatch.  Section 4 describes how RPL artifacts in data
   packets can be compressed as 6LoRH headers.

3.2.  Placement Of 6LoRH headers

3.2.1.  Relative To Non-6LoRH Headers

   In a zone of a packet where Page 1 is active (that is, once the Page
   1 Paging Dispatch is parsed, and until another Paging Dispatch is
   parsed as described in the 6LoWPAN Paging Dispatch specification
   [I-D.ietf-6lo-paging-dispatch]), the parsing of the packet MUST
   follow this specification if the 6LoRH Bit Pattern (see Section 3.1)
   is found.

   With this specification, the 6LoRH Dispatch is only defined in Page
   1, so it MUST be placed in the packet in a zone where the Page 1
   context is active.

   Because a 6LoRH header requires a Page 1 context, it MUST always be
   placed after any Fragmentation Header and/or Mesh Header as defined
   in RFC 4944 [RFC4944].

   A 6LoRH header MUST always be placed before the LOWPAN_IPHC as
   defined in RFC 6282 [RFC6282].  It is designed in such a fashion that
   placing or removing a header that is encoded with 6LoRH does not
   modify the part of the packet that is encoded with LOWPAN_IPHC,
   whether there is an IP-in-IP encapsulation or not.  For instance, the
   final destination of the packet is always the one in the LOWPAN_IPHC
   whether there is a Routing Header or not.

3.2.2.  Relative To Other 6LoRH Headers

   The "Internet Protocol, Version 6 (IPv6) Specification" [RFC2460]
   defines chains of headers that are introduced by an IPv6 header and
   terminated by either another IPv6 header (IP-in-IP) or an Upper Layer
   Protocol (ULP) header.  When an outer header is stripped from the
   packet, the whole chain goes with it.  When one or more header(s) are
   inserted by an intermediate router, that router normally chains the
   headers and encapsulates the result in IP-in-IP.

   With this specification, the chains of headers MUST be compressed in
   the same order as they appear in the uncompressed form of the packet.
   This means that if there is more than one nested IP-in-IP



Thubert, et al.          Expires April 30, 2017                 [Page 7]


Internet-Draft           6LoWPAN Routing Header             October 2016


   encapsulations, the first IP-in-IP encapsulation, with all its chain
   of headers, is encoded first in the compressed form.

   In the compressed form of a packet that has a Source Route or a Hop-
   by-Hop (HbH) Options Header [RFC2460] after the inner IPv6 header
   (e.g., if there is no IP-in-IP encapsulation), these headers are
   placed in the 6LoRH form before the 6LOWPAN_IPHC that represents the
   IPv6 header (see Section 3.2.1).  If this packet gets encapsulated
   and some other SRH or HbH Options Headers are added as part of the
   encapsulation, placing the 6LoRH headers next to one another may
   present an ambiguity on which header belong to which chain in the
   uncompressed form.

   In order to disambiguate the headers that follow the inner IPv6
   header in the uncompressed form from the headers that follow the
   outer IP-in-IP header, it is REQUIRED that the compressed IP-in-IP
   header is placed last in the encoded chain.  This means that the
   6LoRH headers that are found after the last compressed IP-in-IP
   header are to be inserted after the IPv6 header that is encoded with
   the 6LOWPAN_IPHC when decompressing the packet.

   With regards to the relative placement of the SRH and the RPI in the
   compressed form, it is a design point for this specification that the
   SRH entries are consumed as the packet progresses down the LLN (see
   Section 5.3).  In order to make this operation simpler in the
   compressed form, it is REQUIRED that in the compressed form, the
   addresses along the source route path are encoded in the order of the
   path, and that the compressed SRH are placed before the compressed
   RPI.

4.  6LoWPAN Routing Header General Format

   The 6LoRH uses the Dispatch Value Bit Pattern of 10xxxxxx in Page 1.

   The Dispatch Value Bit Pattern is split in two forms of 6LoRH:

      Elective (6LoRHE) that may skipped if not understood

      Critical (6LoRHC) that may not be ignored

   For each form, a Type field is used to encode the type of 6LoRH.

   Note that there is a different registry for the Type field of each
   form of 6LoRH.

   This means that a value for the Type that is defined for one form of
   6LoRH may be redefined in the future for the other form.




Thubert, et al.          Expires April 30, 2017                 [Page 8]


Internet-Draft           6LoWPAN Routing Header             October 2016


4.1.  Elective Format

   The 6LoRHE uses the Dispatch Value Bit Pattern of 101xxxxx.  A 6LoRHE
   may be ignored and skipped in parsing.  If it is ignored, the 6LoRHE
   is forwarded with no change inside the LLN.

       0                   1
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-       ...        -+
      |1|0|1| Length  |      Type     |                    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-       ...        -+
                                       <--    Length    -->

                Figure 3: Elective 6LoWPAN Routing Header.

   Length:  Length of the 6LoRHE expressed in bytes, excluding the first
         2 bytes.  This enables a node to skip a 6LoRHE header that it
         does not support and/or cannot parse, for instance if the Type
         is not recognized.

   Type: Type of the 6LoRHE

4.2.  Critical Format

   The 6LoRHC uses the Dispatch Value Bit Pattern of 100xxxxx.

   A node which does not support the 6LoRHC Type MUST silently discard
   the packet.

   Note: the situation where a node receives a message with a Critical
   6LoWPAN Routing Header that it does not understand should not occur
   and is an administrative error, see Section 8.

     0                   1
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-              ...               -+
    |1|0|0|   TSE   |      Type     |                                  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-              ...               -+
                                     <-- Length implied by Type/TSE -->

                Figure 4: Critical 6LoWPAN Routing Header.

   TSE:  Type Specific Extension.  The meaning depends on the Type,
         which must be known in all of the nodes.  The interpretation of
         the TSE depends on the Type field that follows.  For instance,
         it may be used to transport control bits, the number of
         elements in an array, or the length of the remainder of the
         6LoRHC expressed in a unit other than bytes.



Thubert, et al.          Expires April 30, 2017                 [Page 9]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Type: Type of the 6LoRHC

4.3.  Compressing Addresses

   The general technique used in this draft to compress an address is
   first to determine a reference that has a long prefix match with this
   address, and then elide that matching piece.  In order to reconstruct
   the compressed address, the receiving node will perform the process
   of coalescence described in Section 4.3.1.

   One possible reference is the root of the RPL DODAG that is being
   traversed.  It is used by 6LoRH as the reference to compress an outer
   IP header, in case of an IP-in-IP encapsulation.  If the root is the
   source of the packet, this technique allows to fully elide the source
   address in the compressed form of the IP header.  If the root is not
   the encapsulator, then the encapsulator address may still be
   compressed using the root as reference.  How the address of the root
   is determined is discussed in Section 4.3.2.

   Once the address of the source of the packet is determined, it
   becomes the reference for the compression of the addresses that are
   located in compressed SRH headers that are present inside the IP-in-
   IP encapsulation in the uncompressed form.

4.3.1.  Coalescence

   An IPv6 compressed address is coalesced with a reference address by
   overriding the N rightmost bytes of the reference address with the
   compressed address, where N is the length of the compressed address,
   as indicated by the Type of the SRH-6LoRH header in Figure 7.

   The reference address MAY be a compressed address as well, in which
   case it MUST be compressed in a form that is of an equal or greater
   length than the address that is being coalesced.

   A compressed address is expanded by coalescing it with a reference
   address.  In the particular case of a Type 4 SRH-6LoRH, the address
   is expressed in full and the coalescence is a complete override as
   illustrated in Figure 5.

   RRRRRRRRRRRRRRRRRRR  reference address, may be compressed or not

               CCCCCCC  compressed address, shorter or same as reference

   RRRRRRRRRRRRCCCCCCC  coalesced address, same compression as reference

                      Figure 5: Coalescing addresses.




Thubert, et al.          Expires April 30, 2017                [Page 10]


Internet-Draft           6LoWPAN Routing Header             October 2016


4.3.2.  DODAG Root Address Determination

   Stateful Address compression requires that some state is installed in
   the devices to store the compression information that is elided from
   the packet.  That state is stored in an abstract context table and
   some form of index is found in the packet to obtain the compression
   information from the context table.

   With RFC 6282 [RFC6282], the state is provided to the stack by the
   "6LoWPAN Neighbor Discovery Protocol (NDP)" [RFC6775].  NDP exchanges
   the context through 6LoWPAN Context Option in Router Advertisement
   (RA) messages.  In the compressed form of the packet, the context can
   be signaled in a Context Identifier Extension.

   With this specification, the compression information is provided to
   the stack by RPL, and RPL exchanges it through the DODAGID field in
   the DAG Information Object (DIO) messages, as described in more
   detail below.  In the compressed form of the packet, the context can
   be signaled in by the RPLInstanceID in the RPI.

   With RPL [RFC6550], the address of the DODAG root is known from the
   DODAGID field of the DIO messages.  For a Global Instance, the
   RPLInstanceID that is present in the RPI is enough information to
   identify the DODAG that this node participates to and its associated
   root.  But for a Local Instance, the address of the root MUST be
   explicit, either in some device configuration or signaled in the
   packet, as the source or the destination address, respectively.

   When implicit, the address of the DODAG root MUST be determined as
   follows:

      If the whole network is a single DODAG then the root can be well-
      known and does not need to be signaled in the packets.  But since
      RPL does not expose that property, it can only be known by a
      configuration applied to all nodes.

      Else, the router that encapsulates the packet and compresses it
      with this specification MUST also place an RPI in the packet as
      prescribed by RPL to enable the identification of the DODAG.  The
      RPI must be present even in the case when the router also places
      an SRH header in the packet.

   It is expected that the RPL implementation maintains an abstract
   context table, indexed by Global RPLInstanceID, that provides the
   address of the root of the DODAG that this nodes participates to for
   that particular RPL Instance.





Thubert, et al.          Expires April 30, 2017                [Page 11]


Internet-Draft           6LoWPAN Routing Header             October 2016


5.  The SRH 6LoRH Header

5.1.  Encoding

   A Source Routing Header 6LoRH (SRH-6LoRH) header provides a
   compressed form for the SRH, as defined in RFC 6554 [RFC6554] for use
   by RPL routers.

   One or more SRH-6LoRH header(s) MAY be placed in a 6LoWPAN packet.

   If a non-RPL router receives a packet with a SRH-6LoRH header, there
   was a routing or a configuration error (see Section 8).

   The desired reaction for the non-RPL router is to drop the packet as
   opposed to skip the header and forward the packet.

   The Dispatch Value Bit Pattern for the SRH-6LoRH header indicates
   Critical.  Routers that understand the 6LoRH general format detailed
   in Section 4 cannot ignore a 6LoRH header of this type, and will drop
   the packet if it is unknown to them.

       0                   1
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-    -+-    -+ ... +-    -+
      |1|0|0|  Size   |6LoRH Type 0..4| Hop1 | Hop2 |     | HopN |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-    -+-    -+ ... +-    -+

                Where N = Size + 1

                         Figure 6: The SRH-6LoRH.

   The 6LoRH Type of a SRH-6LoRH header indicates the compression level
   used for that header.

   The fields following the 6LoRH Type are compressed addresses
   indicating the consecutive hops, and are ordered from the first to
   the last hop.

   All the addresses in a given SRH-6LoRH header MUST be compressed in
   an identical fashion, so the Length of the compressed form is the
   same for all.

   In order to get different degrees of compression, multiple
   consecutive SRH-6LoRH headers MUST be used.

   Type 0 means that the address is compressed down to one byte, whereas
   Type 4 means that the address is provided in full in the SRH-6LoRH




Thubert, et al.          Expires April 30, 2017                [Page 12]


Internet-Draft           6LoWPAN Routing Header             October 2016


   with no compression.  The complete list of Types of SRH-6LoRH and the
   corresponding compression level are provided in Figure 7:

     +-----------+----------------------+
     |   6LoRH   | Length of compressed |
     |   Type    | IPv6 address (bytes) |
     +-----------+----------------------+
     |    0      |       1              |
     |    1      |       2              |
     |    2      |       4              |
     |    3      |       8              |
     |    4      |      16              |
     +-----------+----------------------+

                      Figure 7: The SRH-6LoRH Types.

   In the case of a SRH-6LoRH header, the TSE field is used as a Size,
   which encodes the number of hops minus 1; so a Size of 0 means one
   hop, and the maximum that can be encoded is 32 hops.  (If more than
   32 hops need to be expressed, a sequence of SRH-6LoRH elements can be
   employed.)  It results that the Length in bytes of a SRH-6LoRH header
   is:

   2 + Length_of_compressed_IPv6_address * (Size + 1)

5.2.  SRH-6LoRH General Operation

5.2.1.  Uncompressed SRH Operation

   In the non-compressed form, when the root generates or forwards a
   packet in non-Storing Mode, it needs to include a Source Routing
   Header [RFC6554] to signal a strict source-route path to a final
   destination down the DODAG.

   All the hops along the path, but the first one, are encoded in order
   in the SRH.  The last entry in the SRH is the final destination and
   the destination in the IPv6 header is the first hop along the source-
   route path.  The intermediate hops perform a swap and the Segment-
   Left field indicates the active entry in the Routing Header
   [RFC2460].

   The current destination of the packet, which is the termination of
   the current segment, is indicated at all times by the destination
   address of the IPv6 header.







Thubert, et al.          Expires April 30, 2017                [Page 13]


Internet-Draft           6LoWPAN Routing Header             October 2016


5.2.2.  6LoRH-Compressed SRH Operation

   The handling of the SRH-6LoRH is different: there is no swap, and a
   forwarding router that corresponds to the first entry in the first
   SRH-6LoRH upon reception of a packet effectively consumes that entry
   when forwarding.  This means that the size of a compressed source-
   routed packet decreases as the packet progresses along its path and
   that the routing information is lost along the way.  This also means
   that an SRH encoded with 6LoRH is not recoverable and cannot be
   protected.

   When compressed with this specification, all the remaining hops MUST
   be encoded in order in one or more consecutive SRH-6LoRH headers.
   Whether or not there is a SRH-6LoRH header present, the address of
   the final destination is indicated in the LOWPAN_IPHC at all times
   along the path.  Examples of this are provided in Appendix A.

   The current destination (termination of the current segment) for a
   compressed source-routed packet is indicated in the first entry of
   the first SRH-6LoRH.  In strict source-routing, that entry MUST match
   an address of the router that receives the packet.

   The last entry in the last SRH-6LoRH is the last router on the way to
   the final destination in the LLN.  This router can be the final
   destination if it is found desirable to carry a whole IP-in-IP
   encapsulation all the way.  Else, it is the RPL parent of the final
   destination, or a router acting at 6LR [RFC6775] for the destination
   host, and advertising the host as an external route to RPL.

   If the SRH-6LoRH header is contained in an IP-in-IP encapsulation,
   the last router removes the whole chain of headers.  Otherwise, it
   removes the SRH-6LoRH header only.

5.2.3.  Inner LOWPAN_IPHC Compression

   6LoWPAN ND [RFC6282] is designed to support more than one IPv6
   address per node and per Interface Identifier (IID), an IID being
   typically derived from a MAC address to optimize the LOWPAN_IPHC
   compression.

   Link local addresses are compressed with stateless address
   compression (S/DAC=0).  The other addresses are derived from
   different prefixes and they can be compressed with stateful address
   compression based on a context (S/DAC=1).

   But stateless compression is only defined for the specific link-local
   prefix as opposed to the prefix in an encapsulating header.  And with




Thubert, et al.          Expires April 30, 2017                [Page 14]


Internet-Draft           6LoWPAN Routing Header             October 2016


   stateful compression, the compression reference is found in a
   context, as opposed to an encapsulating header.

   It results that in the case of an IP-in-IP encapsulation, it is
   possible to compress an inner source (respectively destination) IP
   address in a LOWPAN_IPHC based on the encapsulating IP header only if
   stateful (context-based) compression is used.  The compression will
   operate only if the IID in the source (respectively the destination)
   IP address in the outer and inner headers match, which usually means
   that they refer to the same node . This is encoded as S/DAC = 1 and
   S/AM=11.  It must be noted that the outer destination address that is
   used to compress the inner destination address is the last entry in
   the last SRH-6LoRH header.

5.3.  The Design Point of Popping Entries

   In order to save energy and to optimize the chances of transmission
   success on lossy media, it is a design point for this specification
   that the entries in the SRH that have been used are removed from the
   packet.  This creates a discrepancy from the art of IPv6 where
   Routing Header are mutable but recoverable.

   With this specification, the packet can be expanded at any hop into a
   valid IPv6 packet, including a SRH, and compressed back.  But the
   packet as decompressed along the way will not carry all the consumed
   addresses that packet would have if it had been forwarded in the
   uncompressed form.

   It is noted that:

      The value of keeping the whole RH in an IPv6 header is for the
      receiver to reverse it to use the symmetrical path on the way
      back.

      It is generally not a good idea to reverse a routing header.  The
      RH may have been used to stay away from the shortest path for some
      reason that is only valid on the way in (segment routing).

      There is no use of reversing a RH in the present RPL
      specifications.

      P2P RPL reverses a path that was learned reactively, as a part of
      the protocol operation, which is probably a cleaner way than a
      reversed echo on the data path.

      Reversing a header is discouraged by RFC 2460 [RFC2460] for RH0
      unless it is authenticated, which requires an Authentication




Thubert, et al.          Expires April 30, 2017                [Page 15]


Internet-Draft           6LoWPAN Routing Header             October 2016


      Header (AH).  There is no definition of an AH operation for SRH,
      and there is no indication that the need exists in LLNs.

      It is noted that AH does not protect the RH on the way.  AH is a
      validation at the receiver with the sole value of enabling the
      receiver to reversing it.

      A RPL domain is usually protected by L2 security and that secures
      both RPL itself and the RH in the packets, at every hop.  This is
      a better security than that provided by AH.

   In summary, the benefit of saving energy and lowering the chances of
   loss by sending smaller frames over the LLN are seen as overwhelming
   compared to the value of possibly reversing the header.

5.4.  Compression Reference for SRH-6LoRH header entries

   In order to optimize the compression of IP addresses present in the
   SRH headers, this specification requires that the 6LoWPAN layer
   identifies an address that is used as reference for the compression.

   With this specification, the Compression Reference for the first
   address found in an SRH header is the source of the IPv6 packet, and
   then the reference for each subsequent entry is the address of its
   predecessor once it is uncompressed.

   With RPL [RFC6550], an SRH header may only be present in Non-Storing
   mode, and it may only be placed in the packet by the root of the
   DODAG, which must be the source of the resulting IPv6 packet
   [RFC2460].  In this case, the address used as Compression Reference
   is the address of the root.

   The Compression Reference MUST be determined as follows:

   The reference address may be obtained by configuration.  The
   configuration may indicate either the address in full, or the
   identifier of a 6LoWPAN Context that carries the address [RFC6775],
   for instance one of the 16 Context Identifiers used in LOWPAN_IPHC
   [RFC6282].

   Else, and if there is no IP-in-IP encapsulation, the source address
   in the IPv6 header that is compressed with LOWPAN_IPHC is the
   reference for the compression.

   Else, and if the IP-in-IP compression specified in this document is
   used and the Encapsulator Address is provided, then the Encapsulator
   Address is the reference.




Thubert, et al.          Expires April 30, 2017                [Page 16]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Else, meaning that the IP-in-IP compression specified in this
   document is used and the encapsulator is implicitly the root, the
   address of the root is the reference.

5.5.  Popping Headers

   Upon reception, the router checks whether the address in the first
   entry of the first SRH-6LoRH one of its own addresses.  In that case,
   router MUST consume that entry before forwarding, which is an action
   of popping from a stack, where the stack is effectively the sequence
   of entries in consecutive SRH-6LoRH headers.

   Popping an entry of an SRH-6LoRH header is a recursive action
   performed as follows:

   If the Size of the SRH-6LoRH header is 1 or more, indicating that
   there are at least 2 entries in the header, the router removes the
   first entry and decrements the Size (by 1).

   Else (meaning that this is the last entry in the SRH-6LoRH header),
   and if there is no next SRH-6LoRH header after this then the SRH-
   6LoRH is removed.

   Else, if there is a next SRH-6LoRH of a Type with a larger or equal
   value, meaning a same or lesser compression yielding same or larger
   compressed forms, then the SRH-6LoRH is removed.

   Else, the first entry of the next SRH-6LoRH is popped from the next
   SRH-6LoRH and coalesced with the first entry of this SRH-6LoRH.

   At the end of the process, if there is no more SRH-6LoRH in the
   packet, then the processing node is the last router along the source
   route path.

   An example of this operation is provided in Appendix A.3.

5.6.  Forwarding

   When receiving a packet with a SRH-6LoRH, a router determines the
   IPv6 address of the current segment endpoint.

   If strict source routing is enforced and this router is not the
   segment endpoint for the packet then this router MUST drop the
   packet.

   If this router is the current segment endpoint, then the router pops
   its address as described in Section 5.5 and continues processing the
   packet.



Thubert, et al.          Expires April 30, 2017                [Page 17]


Internet-Draft           6LoWPAN Routing Header             October 2016


   If there is still a SRH-6LoRH, then the router determines the new
   segment endpoint and routes the packet towards that endpoint.

   Otherwise the router uses the destination in the inner IP header to
   forward or accept the packet.

   The segment endpoint of a packet MUST be determined as follows:

   The router first determines the Compression Reference as discussed in
   Section 4.3.1.

   The router then coalesces the Compression Reference with the first
   entry of the first SRH-6LoRH header as discussed in Section 5.4.  If
   the type of the SRH-6LoRH header is type 4 then the coalescence is a
   full override.

   Since the Compression Reference is an uncompressed address, the
   coalesced IPv6 address is also expressed in the full 128bits.

6.  The RPL Packet Information 6LoRH

   RPL [RFC6550], Section 11.2, specifies the RPL Packet Information
   (RPI) as a set of fields that are placed by RPL routers in IP packets
   to identify the RPL Instance, detect anomalies and trigger corrective
   actions.

   In particular, the SenderRank, which is the scalar metric computed by
   a specialized Objective Function such as described in RFC 6552
   [RFC6552], indicates the Rank of the sender and is modified at each
   hop.  The SenderRank field is used to validate that the packet
   progresses in the expected direction, either upwards or downwards,
   along the DODAG.

   RPL defines the "RPL Option for Carrying RPL Information in Data-
   Plane Datagrams" [RFC6553] to transport the RPI, which is carried in
   an IPv6 Hop-by-Hop Options Header [RFC2460], typically consuming
   eight bytes per packet.

   With RFC 6553 [RFC6553], the RPL option is encoded as six octets,
   which must be placed in a Hop-by-Hop header that consumes two
   additional octets for a total of eight octets.  To limit the header's
   range to just the RPL domain, the Hop-by-Hop header must be added to
   (or removed from) packets that cross the border of the RPL domain.

   The 8-byte overhead is detrimental to LLN operation, in particular
   with regards to bandwidth and battery constraints.  These bytes may
   cause a containing frame to grow above maximum frame size, leading to
   Layer 2 or 6LoWPAN [RFC4944] fragmentation, which in turn leads to



Thubert, et al.          Expires April 30, 2017                [Page 18]


Internet-Draft           6LoWPAN Routing Header             October 2016


   even more energy expenditure and issues discussed in "LLN Fragment
   Forwarding and Recovery" [I-D.thubert-6lo-forwarding-fragments].

   An additional overhead comes from the need, in certain cases, to add
   an IP-in-IP encapsulation to carry the Hop-by-Hop header.  This is
   needed when the router that inserts the Hop-by-Hop header is not the
   source of the packet, so that an error can be returned to the router.
   This is also the case when a packet originated by a RPL node must be
   stripped from the Hop-by-Hop header to be routed outside the RPL
   domain.

   For that reason, this specification defines an IP-in-IP-6LoRH header
   in Section 7, but it must be noted that removal of a 6LoRH header
   does not require manipulation of the packet in the LOWPAN_IPHC, and
   thus, if the source address in the LOWPAN_IPHC is the node that
   inserted the IP-in-IP-6LoRH header then this situation alone does not
   mandate an IP-in-IP-6LoRH header.

   Note: it was found that some implementations omit the RPI for packets
   going down the RPL graph in Non-Storing Mode, even though RPL
   indicates that the RPI should be placed in the packet.  With this
   specification, the RPI is important to indicate the RPLInstanceID so
   the RPI should not be omitted.

   As a result, a RPL packet may bear only an RPI-6LoRH header and no
   IP-in-IP-6LoRH header.  In that case, the source and destination of
   the packet are specified by the LOWPAN_IPHC.

   As with RFC 6553 [RFC6553], the fields in the RPI include an 'O', an
   'R', and an 'F' bit, an 8-bit RPLInstanceID (with some internal
   structure), and a 16-bit SenderRank.

   The remainder of this section defines the RPI-6LoRH header, which is
   a Critical 6LoWPAN Routing Header that is designed to transport the
   RPI in 6LoWPAN LLNs.

6.1.  Compressing the RPLInstanceID

   RPL Instances are discussed in Section 5 of the RPL specification
   [RFC6550].  A number of simple use cases do not require more than one
   RPL Instance, and in such cases, the RPL Instance is expected to be
   the Global Instance 0.  A global RPLInstanceID is encoded in a
   RPLInstanceID field as follows:








Thubert, et al.          Expires April 30, 2017                [Page 19]


Internet-Draft           6LoWPAN Routing Header             October 2016


       0 1 2 3 4 5 6 7
      +-+-+-+-+-+-+-+-+
      |0|     ID      |  Global RPLInstanceID in 0..127
      +-+-+-+-+-+-+-+-+

        Figure 8: RPLInstanceID Field Format for Global Instances.

   For the particular case of the Global Instance 0, the RPLInstanceID
   field is all zeros.  This specification allows to elide a
   RPLInstanceID field that is all zeros, and defines a I flag that,
   when set, signals that the field is elided.

6.2.  Compressing the SenderRank

   The SenderRank is the result of the DAGRank operation on the rank of
   the sender; here the DAGRank operation is defined in Section 3.5.1 of
   the RPL specification [RFC6550] as:

      DAGRank(rank) = floor(rank/MinHopRankIncrease)

   If MinHopRankIncrease is set to a multiple of 256, the least
   significant 8 bits of the SenderRank will be all zeroes; by eliding
   those, the SenderRank can be compressed into a single byte.  This
   idea is used in RFC 6550 [RFC6550] by defining
   DEFAULT_MIN_HOP_RANK_INCREASE as 256 and in RFC 6552 [RFC6552] that
   defaults MinHopRankIncrease to DEFAULT_MIN_HOP_RANK_INCREASE.

   This specification allows to encode the SenderRank as either one or
   two bytes, and defines a K flag that, when set, signals that a single
   byte is used.

6.3.  The Overall RPI-6LoRH encoding

   The RPI-6LoRH header provides a compressed form for the RPL RPI.
   Routers that need to forward a packet with a RPI-6LoRH header are
   expected to be RPL routers that support this specification.

   If a non-RPL router receives a packet with a RPI-6LoRH header, there
   was a routing or a configuration error (see Section 8).

   The desired reaction for the non-RPL router is to drop the packet as
   opposed to skip the header and forward the packet, which could end up
   forming loops by reinjecting the packet in the wrong RPL Instance.

   The Dispatch Value Bit Pattern for the SRH-6LoRH header indicates
   Critical.  Routers that understand the 6LoRH general format detailed
   in Section 4 cannot ignore a 6LoRH header of this type, and will drop
   the packet if it is unknown to them.



Thubert, et al.          Expires April 30, 2017                [Page 20]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Since the RPI-6LoRH header is a critical header, the TSE field does
   not need to be a length expressed in bytes.  In that case the field
   is fully reused for control bits that encode the O, R and F flags
   from the RPI, as well as the I and K flags that indicate the
   compression format.

   The Type for the RPI-6LoRH is 5.

   The RPI-6LoRH header is immediately followed by the RPLInstanceID
   field, unless that field is fully elided, and then the SenderRank,
   which is either compressed into one byte or fully in-lined as two
   bytes.  The I and K flags in the RPI-6LoRH header indicate whether
   the RPLInstanceID is elided and/or the SenderRank is compressed.
   Depending on these bits, the Length of the RPI-6LoRH may vary as
   described hereafter.

       0                   1                   2
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  ...  -+-+-+
      |1|0|0|O|R|F|I|K| 6LoRH Type=5  |   Compressed fields  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  ...  -+-+-+

                  Figure 9: The Generic RPI-6LoRH Format.

   O, R, and F bits:  The O, R, and F bits are defined in section 11.2
         of RFC 6550 [RFC6550].

   I flag:  If it is set, the RPLInstanceID is elided and the
         RPLInstanceID is the Global RPLInstanceID 0.  If it is not set,
         the octet immediately following the type field contains the
         RPLInstanceID as specified in section 5.1 of RFC 6550
         [RFC6550].

   K flag:  If it is set, the SenderRank is compressed into one octet,
         with the least significant octet elided.  If it is not set, the
         SenderRank, is fully inlined as two octets.

   In Figure 10, the RPLInstanceID is the Global RPLInstanceID 0, and
   the MinHopRankIncrease is a multiple of 256 so the least significant
   byte is all zeros and can be elided:











Thubert, et al.          Expires April 30, 2017                [Page 21]


Internet-Draft           6LoWPAN Routing Header             October 2016


       0                   1                   2
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1|0|0|O|R|F|1|1| 6LoRH Type=5  | SenderRank    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                I=1, K=1

                 Figure 10: The most compressed RPI-6LoRH.

   In Figure 11, the RPLInstanceID is the Global RPLInstanceID 0, but
   both bytes of the SenderRank are significant so it can not be
   compressed:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1|0|0|O|R|F|1|0| 6LoRH Type=5  |        SenderRank             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                I=1, K=0

                   Figure 11: Eliding the RPLInstanceID.

   In Figure 12, the RPLInstanceID is not the Global RPLInstanceID 0,
   and the MinHopRankIncrease is a multiple of 256:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1|0|0|O|R|F|0|1| 6LoRH Type=5  | RPLInstanceID |  SenderRank   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                I=0, K=1

                    Figure 12: Compressing SenderRank.

   In Figure 13, the RPLInstanceID is not the Global RPLInstanceID 0,
   and both bytes of the SenderRank are significant:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1|0|0|O|R|F|0|0| 6LoRH Type=5  | RPLInstanceID |    Sender-...
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
        ...-Rank      |
      +-+-+-+-+-+-+-+-+
                I=0, K=0

              Figure 13: Least compressed form of RPI-6LoRH.




Thubert, et al.          Expires April 30, 2017                [Page 22]


Internet-Draft           6LoWPAN Routing Header             October 2016


7.  The IP-in-IP 6LoRH Header

   The IP-in-IP 6LoRH (IP-in-IP-6LoRH) header is an Elective 6LoWPAN
   Routing Header that provides a compressed form for the encapsulating
   IPv6 Header in the case of an IP-in-IP encapsulation.

   An IP-in-IP encapsulation is used to insert a field such as a Routing
   Header or an RPI at a router that is not the source of the packet.
   In order to send an error back regarding the inserted field, the
   address of the router that performs the insertion must be provided.

   The encapsulation can also enable the last router prior to
   Destination to remove a field such as the RPI, but this can be done
   in the compressed form by removing the RPI-6LoRH, so an IP-in-IP-
   6LoRH encapsulation is not required for that sole purpose.

   The Dispatch Value Bit Pattern for the SRH-6LoRH header indicates
   Elective.  This field is not critical for routing since it does not
   indicate the destination of the packet, which is either encoded in a
   SRH-6LoRH header or in the inner IP header.  A 6LoRH header of this
   type can be skipped if not understood (per Section 4), and the 6LoRH
   header indicates the Length in bytes.

     0                   1                   2
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-       ...      -+
    |1|0|1| Length  | 6LoRH Type 6  |  Hop Limit    | Encaps. Address  |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-       ...      -+


                      Figure 14: The IP-in-IP-6LoRH.

   The Length of an IP-in-IP-6LoRH header is expressed in bytes and MUST
   be at least 1, to indicate a Hop Limit (HL), that is decremented at
   each hop.  When the HL reaches 0, the packet is dropped per RFC 2460
   [RFC2460].

   If the Length of an IP-in-IP-6LoRH header is exactly 1, then the
   Encapsulator Address is elided, which means that the Encapsulator is
   a well-known router, for instance the root in a RPL graph.

   The most efficient compression of an IP-in-IP encapsulation that can
   be achieved with this specification is obtained when an endpoint of
   the packet is the root of the RPL DODAG associated to the RPL
   Instance that is used to forward the packet, and the root address is
   known implicitly as opposed to signaled explicitly in the data
   packets.




Thubert, et al.          Expires April 30, 2017                [Page 23]


Internet-Draft           6LoWPAN Routing Header             October 2016


   If the Length of an IP-in-IP-6LoRH header is greater than 1, then an
   Encapsulator Address is placed in a compressed form after the Hop
   Limit field.  The value of the Length indicates which compression is
   performed on the Encapsulator Address.  For instance, a Length of 3
   indicates that the Encapsulator Address is compressed to 2 bytes.
   The reference for the compression is the address of the root of the
   DODAG.  The way the address of the root is determined is discussed in
   Section 4.3.2.

   With RPL, the destination address in the IP-in-IP header is
   implicitly the root in the RPL graph for packets going upwards, and,
   in storing mode, it is the destination address in the LOWPAN_IPHC for
   packets going downwards.  In non-storing mode, there is no implicit
   value for packets going downwards.

   If the implicit value is correct, the destination IP address of the
   IP-in-IP encapsulation can be elided.  Else, the destination IP
   address of the IP-in-IP header is transported in a SRH-6LoRH header
   as the first entry of the first of these headers.

   If the final destination of the packet is a leaf that does not
   support this specification, then the chain of 6LoRH headers must be
   stripped by the RPL/6LR router to which the leaf is attached.  In
   that example, the destination IP address of the IP-in-IP header
   cannot be elided.

   In the special case where a 6LoRH header is used to route 6LoWPAN
   fragments, the destination address is not accessible in the
   LOWPAN_IPHC on all fragments and can be elided only for the first
   fragment and for packets going upwards.

8.  Management Considerations

   Though it is possible to decompress a packet at any hop, this
   specification is optimized to enable that a packet is forwarded in
   its compressed form all the way, and it makes sense to deploy
   homogeneous networks, where all nodes, or no node at all, use the
   compression technique detailed therein.

   This specification aims at a simple implementation running in
   constrained nodes, so it does indeed expect an homogeneous network
   and as a consequence it does not provide a method to determine the
   level of support by the next hops at forwarding time.

   Should an extension to this specification provide such a method,
   forwarding nodes could compress or uncompress the RPL artifacts
   appropriately and enable a backward compatibility between nodes that
   support this specification and nodes that do not.



Thubert, et al.          Expires April 30, 2017                [Page 24]


Internet-Draft           6LoWPAN Routing Header             October 2016


   It results that this specification does not attempt to enable such
   backwards compatibility.  It does not require extraneous code to
   exchange and handle error messages to correct automatically mismatch
   situations, either.

   When a packet is expected to carry a 6LoRH header but it does not,
   the node that discovers the issue is expected to send an ICMPv6 error
   message to the root, at an adapted rate limitation and with a Type 4
   indicating a "Parameter Problem", and a Code 0 indicating an
   "erroneous header field encountered", embedding the relevant portion
   of the received packet and pointing at the offset therein where the
   6LoRH header was expected.

   When a packet is received with a 6LoRH header that is not recognized,
   the node that discovers the issue is expected to send an ICMPv6 error
   message, to the root, at an adapted rate limitation and with a Type 4
   indicating a "Parameter Problem", and a Code 1 indicating an
   "unrecognized Next Header type", embedding the relevant portion of
   the received packet and pointing at the offset therein where the
   6LoRH header was expected.

   In both cases, the node SHOULD NOT place a 6LoRH header defined in
   this specification in the resulting message, and should either omit
   the RPI or place it uncompressed after the IPv6 header.

   In both cases also, an alternate management method may be preferred
   in order to notify the network administrator that there is a
   configuration error.

   Keeping the network homogeneous is either a deployment issue, by
   deploying only devices with a same capability, or a management issue,
   by configuring all devices to either use, or not use, a certain level
   of this compression technique and its future additions.

   In particular, the situation where a node receives a message with a
   Critical 6LoWPAN Routing Header that it does not understand is an
   administrative error whereby the wrong device is placed in a network,
   or the device is mis-configured.

   When a mismatch situation is detected, it is expected that the device
   raises some management alert, indicating the issue, e.g., that it has
   to drop a packet with a Critical 6LoRH.

9.  Security Considerations

   The security considerations of RFC 4944 [RFC4944], RFC 6282
   [RFC6282], and RFC 6553 [RFC6553] apply.




Thubert, et al.          Expires April 30, 2017                [Page 25]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Using a compressed format as opposed to the full in-line format is
   logically equivalent and is believed to not create an opening for a
   new threat when compared to RFC 6550 [RFC6550], RFC 6553 [RFC6553]
   and RFC 6554 [RFC6554], noting that, even though intermediate hops
   are removed from the SRH header as they are consumed, a node may
   still identify that the rest of the source routed path includes a
   loop or not (see Security section of RFC 6554).  It must be noted
   that if the attacker is not part of the loop, then there is always a
   node at the beginning of the loop that can detect it and remove it.

10.  IANA Considerations

10.1.  Reserving Space in 6LoWPAN Dispatch Page 1

   This specification reserves Dispatch Value Bit Patterns within the
   6LoWPAN Dispatch Page 1 as follows:

      101xxxxx: for Elective 6LoWPAN Routing Headers

      100xxxxx: for Critical 6LoWPAN Routing Headers.

   Additionally this document creates two IANA registries, one for the
   Critical 6LoWPAN Routing Header Type and one for the Elective 6LoWPAN
   Routing Header Type, each with 32 possible values from 0 to 31, as
   described below.

   Future assignments in these registries are to be coordinated via IANA
   under the policy of "RFC Required" (per RFC 5226 [RFC5226]) to enable
   any type of RFC to obtain a value in the registry.

10.2.  New Critical 6LoWPAN Routing Header Type Registry

   This document creates an IANA registry for the Critical 6LoWPAN
   Routing Header Type, and assigns the following values:

      0..4: SRH-6LoRH [RFCthis]

      5: RPI-6LoRH [RFCthis]

10.3.  New Elective 6LoWPAN Routing Header Type Registry

   This document creates an IANA registry for the Elective 6LoWPAN
   Routing Header Type, and assigns the following value:

      6: IP-in-IP-6LoRH [RFCthis]






Thubert, et al.          Expires April 30, 2017                [Page 26]


Internet-Draft           6LoWPAN Routing Header             October 2016


11.  Acknowledgments

   The authors wish to thank Tom Phinney, Thomas Watteyne, Tengfei
   Chang, Martin Turon, James Woodyatt, Samita Chakrabarti, Jonathan
   Hui, Gabriel Montenegro and Ralph Droms for constructive reviews to
   the design in the 6lo Working Group.  The overall discussion involved
   participants to the 6MAN, 6TiSCH and ROLL WGs, thank you all.
   Special thanks to the chairs of the ROLL WG, Michael Richardson and
   Ines Robles, Brian Haberman, Internet Area A-D, and Alvaro Retana and
   Adrian Farrel, Routing Area A-Ds, for driving this complex effort
   across Working Groups and Areas.

12.  References

12.1.  Normative References

   [I-D.ietf-6lo-paging-dispatch]
              Thubert, P. and R. Cragie, "6LoWPAN Paging Dispatch",
              draft-ietf-6lo-paging-dispatch-05 (work in progress),
              October 2016.

   [IEEE802154]
              IEEE standard for Information Technology, "IEEE std.
              802.15.4, Part. 15.4: Wireless Medium Access Control (MAC)
              and Physical Layer (PHY) Specifications for Low-Rate
              Wireless Personal Area Networks", 2015.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC2460]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
              December 1998, <http://www.rfc-editor.org/info/rfc2460>.

   [RFC4443]  Conta, A., Deering, S., and M. Gupta, Ed., "Internet
              Control Message Protocol (ICMPv6) for the Internet
              Protocol Version 6 (IPv6) Specification", RFC 4443,
              DOI 10.17487/RFC4443, March 2006,
              <http://www.rfc-editor.org/info/rfc4443>.

   [RFC4944]  Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler,
              "Transmission of IPv6 Packets over IEEE 802.15.4
              Networks", RFC 4944, DOI 10.17487/RFC4944, September 2007,
              <http://www.rfc-editor.org/info/rfc4944>.





Thubert, et al.          Expires April 30, 2017                [Page 27]


Internet-Draft           6LoWPAN Routing Header             October 2016


   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              DOI 10.17487/RFC5226, May 2008,
              <http://www.rfc-editor.org/info/rfc5226>.

   [RFC6282]  Hui, J., Ed. and P. Thubert, "Compression Format for IPv6
              Datagrams over IEEE 802.15.4-Based Networks", RFC 6282,
              DOI 10.17487/RFC6282, September 2011,
              <http://www.rfc-editor.org/info/rfc6282>.

   [RFC6550]  Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
              Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
              JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
              Low-Power and Lossy Networks", RFC 6550,
              DOI 10.17487/RFC6550, March 2012,
              <http://www.rfc-editor.org/info/rfc6550>.

   [RFC6552]  Thubert, P., Ed., "Objective Function Zero for the Routing
              Protocol for Low-Power and Lossy Networks (RPL)",
              RFC 6552, DOI 10.17487/RFC6552, March 2012,
              <http://www.rfc-editor.org/info/rfc6552>.

   [RFC6553]  Hui, J. and JP. Vasseur, "The Routing Protocol for Low-
              Power and Lossy Networks (RPL) Option for Carrying RPL
              Information in Data-Plane Datagrams", RFC 6553,
              DOI 10.17487/RFC6553, March 2012,
              <http://www.rfc-editor.org/info/rfc6553>.

   [RFC6554]  Hui, J., Vasseur, JP., Culler, D., and V. Manral, "An IPv6
              Routing Header for Source Routes with the Routing Protocol
              for Low-Power and Lossy Networks (RPL)", RFC 6554,
              DOI 10.17487/RFC6554, March 2012,
              <http://www.rfc-editor.org/info/rfc6554>.

12.2.  Informative References

   [I-D.ietf-6tisch-architecture]
              Thubert, P., "An Architecture for IPv6 over the TSCH mode
              of IEEE 802.15.4", draft-ietf-6tisch-architecture-10 (work
              in progress), June 2016.

   [I-D.ietf-roll-useofrplinfo]
              Robles, I., Richardson, M., and P. Thubert, "When to use
              RFC 6553, 6554 and IPv6-in-IPv6", draft-ietf-roll-
              useofrplinfo-09 (work in progress), October 2016.






Thubert, et al.          Expires April 30, 2017                [Page 28]


Internet-Draft           6LoWPAN Routing Header             October 2016


   [I-D.thubert-6lo-forwarding-fragments]
              Thubert, P. and J. Hui, "LLN Fragment Forwarding and
              Recovery", draft-thubert-6lo-forwarding-fragments-03 (work
              in progress), October 2016.

   [RFC6775]  Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C.
              Bormann, "Neighbor Discovery Optimization for IPv6 over
              Low-Power Wireless Personal Area Networks (6LoWPANs)",
              RFC 6775, DOI 10.17487/RFC6775, November 2012,
              <http://www.rfc-editor.org/info/rfc6775>.

   [RFC7102]  Vasseur, JP., "Terms Used in Routing for Low-Power and
              Lossy Networks", RFC 7102, DOI 10.17487/RFC7102, January
              2014, <http://www.rfc-editor.org/info/rfc7102>.

   [RFC7228]  Bormann, C., Ersue, M., and A. Keranen, "Terminology for
              Constrained-Node Networks", RFC 7228,
              DOI 10.17487/RFC7228, May 2014,
              <http://www.rfc-editor.org/info/rfc7228>.

   [RFC7554]  Watteyne, T., Ed., Palattella, M., and L. Grieco, "Using
              IEEE 802.15.4e Time-Slotted Channel Hopping (TSCH) in the
              Internet of Things (IoT): Problem Statement", RFC 7554,
              DOI 10.17487/RFC7554, May 2015,
              <http://www.rfc-editor.org/info/rfc7554>.

Appendix A.  Examples

A.1.  Examples Compressing The RPI

   The example in Figure 15 illustrates the 6LoRH compression of a
   classical packet in Storing Mode in all directions, as well as in
   non-Storing mode for a packet going up the DODAG following the
   default route to the root.  In this particular example, a
   fragmentation process takes place per RFC 4944 [RFC4944], and the
   fragment headers must be placed in Page 0 before switching to Page 1:















Thubert, et al.          Expires April 30, 2017                [Page 29]


Internet-Draft           6LoWPAN Routing Header             October 2016


   +-  ...  -+-  ...  -+-+ ... -+- ... +-+-+ ... -+-+-+-+-+-+-+-+-+-+...
   |Frag type|Frag hdr |11110001|  RPI-  |IP-in-IP| LOWPAN_IPHC | ...
   |RFC 4944 |RFC 4944 | Page 1 | 6LoRH  | 6LoRH  |             |
   +-  ...  -+-  ...  -+-+ ... -+- ... +-+-+ ... -+-+-+-+-+-+-+-+-+-+...
                                                   <-  RFC 6282  ->
                                                    No RPL artifact

   +-  ...  -+-  ...  -+-+ ... -+-+ ... -+- ... +-+-+-+-+-+-+-+-+-+-+...
   |Frag type|Frag hdr |
   |RFC 4944 |RFC 4944 |  Payload (cont)
   +-  ...  -+-  ...  -+-+ ... -+-+ ... -+- ... +-+-+-+-+-+-+-+-+-+-+...

   +-  ...  -+-  ...  -+-+ ... -+-+ ... -+- ... +-+-+-+-+-+-+-+-+-+-+...
   |Frag type|Frag hdr |
   |RFC 4944 |RFC 4944 |  Payload (cont)
   +-  ...  -+-  ...  -+-+ ... -+-+ ... -+- ... +-+-+-+-+-+-+-+-+-+-+...




              Figure 15: Example Compressed Packet with RPI.

   In Storing Mode, if the packet stays within the RPL domain, then it
   is possible to save the IP-in-IP encapsulation, in which case only
   the RPI is compressed with a 6LoRH, as illustrated in Figure 16 in
   the case of a non-fragmented ICMP packet:

   +- ...  -+-+- ... -+-+-+-+ ... -+-+-+-+ ... -+-+-+-+-+-+-+-+-+-+-+...
   |11110001| RPI-6LoRH |  NH = 0      | NH = 58  |  ICMP message ...
   |Page 1  |  type 5   | 6LOWPAN_IPHC | (ICMP)   |  (no compression)
   +- ...  -+-+- ... -+-+-+-+ ... -+-+-+-+ ... -+-+-+-+-+-+-+-+-+-+-+...
                         <-      RFC 6282       ->
                             No RPL artifact

         Figure 16: Example ICMP Packet with RPI in Storing Mode.

   The format in Figure 16 is logically equivalent to the non-compressed
   format illustrated in Figure 17:

   +-+-+-+- ... -+-+-+-+ ... -+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...
   |  IPv6 Header  | Hop-by-Hop |  RPI in       |  ICMP message ...
   |  NH = 58      | Header     |  RPL Option   |
   +-+-+-+- ... -+-+-+-+ ... -+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...

               Figure 17: Uncompressed ICMP Packet with RPI.

   For a UDP packet, the transport header can be compressed with 6LoWPAN
   HC [RFC6282] as illustrated in Figure 18:



Thubert, et al.          Expires April 30, 2017                [Page 30]


Internet-Draft           6LoWPAN Routing Header             October 2016


   +-+ ... -+-+-...-+-+- ... -+-+-+-+ ... -+-+-+ ... -+-+-+-+-+...
   |11110001| RPI-  | NH=1        |11110CPP| Compressed | UDP
   |Page 1  | 6LoRH | LOWPAN_IPHC | UDP    | UDP header | Payload
   +-+ ... -+-+-...-+-+- ... -+-+-+-+ ... -+-+-+ ... -+-+-+-+-+...
                     <-         RFC 6282              ->
                                No RPL artifact

               Figure 18: Uncompressed ICMP Packet with RPI.

   If the packet is received from the Internet in Storing Mode, then the
   root is supposed to encapsulate the packet to insert the RPI.  The
   resulting format would be as represented in Figure 19:

 +-+ ... -+-+-...-+-+-- ... -+-+-+-+- ... -+-+ ... -+-+-+ ... -+-+-+...
 |11110001| RPI-  | IP-in-IP | NH=1        |11110CPP| Compressed | UDP
 |Page 1  | 6LoRH |  6LoRH   | LOWPAN_IPHC | UDP    | UDP header | Payld
 +-+ ... -+-+-...-+-+-- ... -+-+-+-+- ... -+-+ ... -+-+-+ ... -+-+-+...
                              <-         RFC 6282              ->
                                         No RPL artifact


           Figure 19: RPI inserted by the root in Storing Mode.

A.2.  Example Of Downward Packet In Non-Storing Mode

   The example illustrated in Figure 20 is a classical packet in non-
   Storing mode for a packet going down the DODAG following a source
   routed path from the root.  Say that we have 4 forwarding hops to
   reach a destination.  In the non-compressed form, when the root
   generates the packet, the last 3 hops are encoded in a Routing Header
   type 3 (SRH) and the first hop is the destination of the packet.  The
   intermediate hops perform a swap and the hop count indicates the
   current active hop as defined in RFC 2460 [RFC2460] and RFC 6554
   [RFC6554].

   When compressed with this specification, the 4 hops are encoded in
   SRH-6LoRH when the root generates the packet, and the final
   destination is left in the LOWPAN_IPHC.  There is no swap, and the
   forwarding node that corresponds to the first entry effectively
   consumes it when forwarding, which means that the size of the encoded
   packet decreases and that the hop information is lost.

   If the last hop in a SRH-6LoRH is not the final destination then it
   removes the SRH-6LoRH before forwarding.

   In the particular example illustrated in Figure 20, all addresses in
   the DODAG are assigned from a same /112 prefix and the last 2 octets
   encoding an identifier such as a IEEE 802.15.4 short address.  In



Thubert, et al.          Expires April 30, 2017                [Page 31]


Internet-Draft           6LoWPAN Routing Header             October 2016


   that case, all addresses can be compressed to 2 octets, using the
   root address as reference.  There will be one SRH_6LoRH header, with,
   in this example, 3 compressed addresses:

 +-+ ... -+-+ ... +-+- ... -+-+- ... +-+-+-+ ... +-+-+ ... -+ ... +-...
 |11110001|SRH-6LoRH| RPI-  | IP-in-IP | NH=1      |11110CPP| UDP | UDP
 |Page 1  |Type1 S=2| 6LoRH |  6LoRH   |LOWPAN_IPHC| UDP    | hdr |Payld
 +-+ ... -+-+ ... +-+- ... -+-+-- ... -+-+-+ ... +-+-+ ... -+ ... +-...
            <-8bytes->                  <-        RFC 6282      ->
                                                No RPL artifact

              Figure 20: Example Compressed Packet with SRH.

   One may note that the RPI is provided.  This is because the address
   of the root that is the source of the IP-in-IP header is elided and
   inferred from the RPLInstanceID in the RPI.  Once found from a local
   context, that address is used as Compression Reference to expand
   addresses in the SRH-6LoRH.

   With the RPL specifications available at the time of writing this
   draft, the root is the only node that may incorporate a SRH in an IP
   packet.  When the root forwards a packet that it did not generate, it
   has to encapsulate the packet with IP-in-IP.

   But if the root generates the packet towards a node in its DODAG,
   then it should avoid the extra IP-in-IP as illustrated in Figure 21:

   +- ...  -+-+-+ ... +-+-+-+ ... -+-+-+-+-+-+-+-++-+- ... -+-+-+-+-+...
   |11110001| SRH-6LoRH | NH=1       | 11110CPP  | Compressed | UDP
   |Page 1  | Type1 S=3 | LOWPAN_IPHC| LOWPAN-NHC| UDP header | Payload
   +- ...  -+-+-+ ... +-+-+-+ ... -+-+-+-+-+-+-+-++-+- ... -+-+-+-+-+...
                                          <-        RFC 6282        ->

        Figure 21: compressed SRH 4*2bytes entries sourced by root.

   Note: the RPI is not represented though RPL [RFC6550] generally
   expects it.  In this particular case, since the Compression Reference
   for the SRH-6LoRH is the source address in the LOWPAN_IPHC, and the
   routing is strict along the source route path, the RPI does not
   appear to be absolutely necessary.

   In Figure 21, all the nodes along the source route path share a same
   /112 prefix.  This is typical of IPv6 addresses derived from an
   IEEE802.15.4 short address, as long as all the nodes share a same
   PAN-ID.  In that case, a type-1 SRH-6LoRH header can be used for
   encoding.  The IPv6 address of the root is taken as reference, and
   only the last 2 octets of the address of the intermediate hops is




Thubert, et al.          Expires April 30, 2017                [Page 32]


Internet-Draft           6LoWPAN Routing Header             October 2016


   encoded.  The Size of 3 indicates 4 hops, resulting in a SRH-6LoRH of
   10 bytes.

A.3.  Example of SRH-6LoRH life-cycle

   This section illustrates the operation specified in Section 5.6 of
   forwarding a packet with a compressed SRH along an A->B->C->D source
   route path.  The operation of popping addresses is exemplified at
   each hop.

   Packet as received by node A
   ----------------------------
     Type 3 SRH-6LoRH Size = 0   AAAA AAAA AAAA AAAA
     Type 1 SRH-6LoRH Size = 0                  BBBB
     Type 2 SRH-6LoRH Size = 1             CCCC CCCC
                                           DDDD DDDD

    Step 1 popping BBBB the first entry of the next SRH-6LoRH
    Step 2 next is if larger value (2 vs. 1) the SRH-6LoRH is removed

     Type 3 SRH-6LoRH Size = 0   AAAA AAAA AAAA AAAA
     Type 2 SRH-6LoRH Size = 1             CCCC CCCC
                                           DDDD DDDD

    Step 3: recursion ended, coalescing BBBB with the first entry
     Type 3 SRH-6LoRH Size = 0   AAAA AAAA AAAA BBBB

    Step 4: routing based on next segment endpoint to B


                     Figure 22: Processing at Node A.




















Thubert, et al.          Expires April 30, 2017                [Page 33]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Packet as received by node B
   ----------------------------
     Type 3 SRH-6LoRH Size = 0   AAAA AAAA AAAA BBBB
     Type 2 SRH-6LoRH Size = 1             CCCC CCCC
                                           DDDD DDDD

    Step 1 popping CCCC CCCC, the first entry of the next SRH-6LoRH
    Step 2 removing the first entry and decrementing the Size (by 1)

     Type 3 SRH-6LoRH Size = 0   AAAA AAAA AAAA BBBB
     Type 2 SRH-6LoRH Size = 0             DDDD DDDD

    Step 3: recursion ended, coalescing CCCC CCCC with the first entry
     Type 3 SRH-6LoRH Size = 0   AAAA AAAA CCCC CCCC

    Step 4: routing based on next segment endpoint to C


                     Figure 23: Processing at Node B.


   Packet as received by node C
   ----------------------------

     Type 3 SRH-6LoRH Size = 0   AAAA AAAA CCCC CCCC
     Type 2 SRH-6LoRH Size = 0             DDDD DDDD

    Step 1 popping DDDD DDDD, the first entry of the next SRH-6LoRH
    Step 2 the SRH-6LoRH is removed

     Type 3 SRH-6LoRH Size = 0   AAAA AAAA CCCC CCCC

    Step 3: recursion ended, coalescing DDDD DDDDD with the first entry
     Type 3 SRH-6LoRH Size = 0   AAAA AAAA DDDD DDDD

    Step 4: routing based on next segment endpoint to D


                     Figure 24: Processing at Node C.












Thubert, et al.          Expires April 30, 2017                [Page 34]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Packet as received by node D
   ----------------------------
     Type 3 SRH-6LoRH Size = 0   AAAA AAAA DDDD DDDD

    Step 1 the SRH-6LoRH is removed.
    Step 2 no more header, routing based on inner IP header.


                     Figure 25: Processing at Node D.

Authors' Addresses

   Pascal Thubert (editor)
   Cisco Systems
   Building D - Regus
   45 Allee des Ormes
   BP1200
   MOUGINS - Sophia Antipolis  06254
   France

   Phone: +33 4 97 23 26 34
   Email: pthubert@cisco.com


   Carsten Bormann
   Universitaet Bremen TZI
   Postfach 330440
   Bremen  D-28359
   Germany

   Phone: +49-421-218-63921
   Email: cabo@tzi.org


   Laurent Toutain
   Institut MINES TELECOM; TELECOM Bretagne
   2 rue de la Chataigneraie
   CS 17607
   Cesson-Sevigne Cedex  35576
   France

   Email: Laurent.Toutain@telecom-bretagne.eu









Thubert, et al.          Expires April 30, 2017                [Page 35]


Internet-Draft           6LoWPAN Routing Header             October 2016


   Robert Cragie
   ARM Ltd.
   110 Fulbourn Road
   Cambridge  CB1 9NJ
   UK

   Email: robert.cragie@gridmerge.com












































Thubert, et al.          Expires April 30, 2017                [Page 36]