Network Working Group                                          J. Uberti
Internet-Draft                                                    Google
Intended status: Standards Track                             C. Jennings
Expires: March 5, 2018                                             Cisco
                                                        E. Rescorla, Ed.
                                                                 Mozilla
                                                       September 1, 2017


               JavaScript Session Establishment Protocol
                       draft-ietf-rtcweb-jsep-23

Abstract

   This document describes the mechanisms for allowing a JavaScript
   application to control the signaling plane of a multimedia session
   via the interface specified in the W3C RTCPeerConnection API, and
   discusses how this relates to existing signaling protocols.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 5, 2018.

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of



Uberti, et al.            Expires March 5, 2018                 [Page 1]


Internet-Draft                    JSEP                    September 2017


   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   4
     1.1.  General Design of JSEP  . . . . . . . . . . . . . . . . .   4
     1.2.  Other Approaches Considered . . . . . . . . . . . . . . .   6
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   6
   3.  Semantics and Syntax  . . . . . . . . . . . . . . . . . . . .   7
     3.1.  Signaling Model . . . . . . . . . . . . . . . . . . . . .   7
     3.2.  Session Descriptions and State Machine  . . . . . . . . .   7
     3.3.  Session Description Format  . . . . . . . . . . . . . . .  11
     3.4.  Session Description Control . . . . . . . . . . . . . . .  11
       3.4.1.  RtpTransceivers . . . . . . . . . . . . . . . . . . .  11
       3.4.2.  RtpSenders  . . . . . . . . . . . . . . . . . . . . .  12
       3.4.3.  RtpReceivers  . . . . . . . . . . . . . . . . . . . .  12
     3.5.  ICE . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
       3.5.1.  ICE Gathering Overview  . . . . . . . . . . . . . . .  12
       3.5.2.  ICE Candidate Trickling . . . . . . . . . . . . . . .  13
         3.5.2.1.  ICE Candidate Format  . . . . . . . . . . . . . .  13
       3.5.3.  ICE Candidate Policy  . . . . . . . . . . . . . . . .  14
       3.5.4.  ICE Candidate Pool  . . . . . . . . . . . . . . . . .  15
     3.6.  Video Size Negotiation  . . . . . . . . . . . . . . . . .  16
       3.6.1.  Creating an imageattr Attribute . . . . . . . . . . .  16
       3.6.2.  Interpreting imageattr Attributes . . . . . . . . . .  17
     3.7.  Simulcast . . . . . . . . . . . . . . . . . . . . . . . .  19
     3.8.  Interactions With Forking . . . . . . . . . . . . . . . .  20
       3.8.1.  Sequential Forking  . . . . . . . . . . . . . . . . .  20
       3.8.2.  Parallel Forking  . . . . . . . . . . . . . . . . . .  21
   4.  Interface . . . . . . . . . . . . . . . . . . . . . . . . . .  22
     4.1.  PeerConnection  . . . . . . . . . . . . . . . . . . . . .  22
       4.1.1.  Constructor . . . . . . . . . . . . . . . . . . . . .  22
       4.1.2.  addTrack  . . . . . . . . . . . . . . . . . . . . . .  24
       4.1.3.  removeTrack . . . . . . . . . . . . . . . . . . . . .  24
       4.1.4.  addTransceiver  . . . . . . . . . . . . . . . . . . .  24
       4.1.5.  createDataChannel . . . . . . . . . . . . . . . . . .  25
       4.1.6.  createOffer . . . . . . . . . . . . . . . . . . . . .  25
       4.1.7.  createAnswer  . . . . . . . . . . . . . . . . . . . .  26
       4.1.8.  SessionDescriptionType  . . . . . . . . . . . . . . .  27
         4.1.8.1.  Use of Provisional Answers  . . . . . . . . . . .  28
         4.1.8.2.  Rollback  . . . . . . . . . . . . . . . . . . . .  28
       4.1.9.  setLocalDescription . . . . . . . . . . . . . . . . .  29
       4.1.10. setRemoteDescription  . . . . . . . . . . . . . . . .  29
       4.1.11. currentLocalDescription . . . . . . . . . . . . . . .  30
       4.1.12. pendingLocalDescription . . . . . . . . . . . . . . .  30
       4.1.13. currentRemoteDescription  . . . . . . . . . . . . . .  30
       4.1.14. pendingRemoteDescription  . . . . . . . . . . . . . .  30



Uberti, et al.            Expires March 5, 2018                 [Page 2]


Internet-Draft                    JSEP                    September 2017


       4.1.15. canTrickleIceCandidates . . . . . . . . . . . . . . .  31
       4.1.16. setConfiguration  . . . . . . . . . . . . . . . . . .  31
       4.1.17. addIceCandidate . . . . . . . . . . . . . . . . . . .  32
     4.2.  RtpTransceiver  . . . . . . . . . . . . . . . . . . . . .  33
       4.2.1.  stop  . . . . . . . . . . . . . . . . . . . . . . . .  33
       4.2.2.  stopped . . . . . . . . . . . . . . . . . . . . . . .  33
       4.2.3.  setDirection  . . . . . . . . . . . . . . . . . . . .  33
       4.2.4.  direction . . . . . . . . . . . . . . . . . . . . . .  33
       4.2.5.  currentDirection  . . . . . . . . . . . . . . . . . .  34
       4.2.6.  setCodecPreferences . . . . . . . . . . . . . . . . .  34
   5.  SDP Interaction Procedures  . . . . . . . . . . . . . . . . .  34
     5.1.  Requirements Overview . . . . . . . . . . . . . . . . . .  34
       5.1.1.  Usage Requirements  . . . . . . . . . . . . . . . . .  35
       5.1.2.  Profile Names and Interoperability  . . . . . . . . .  35
     5.2.  Constructing an Offer . . . . . . . . . . . . . . . . . .  36
       5.2.1.  Initial Offers  . . . . . . . . . . . . . . . . . . .  36
       5.2.2.  Subsequent Offers . . . . . . . . . . . . . . . . . .  43
       5.2.3.  Options Handling  . . . . . . . . . . . . . . . . . .  47
         5.2.3.1.  IceRestart  . . . . . . . . . . . . . . . . . . .  47
         5.2.3.2.  VoiceActivityDetection  . . . . . . . . . . . . .  47
     5.3.  Generating an Answer  . . . . . . . . . . . . . . . . . .  48
       5.3.1.  Initial Answers . . . . . . . . . . . . . . . . . . .  48
       5.3.2.  Subsequent Answers  . . . . . . . . . . . . . . . . .  55
       5.3.3.  Options Handling  . . . . . . . . . . . . . . . . . .  56
         5.3.3.1.  VoiceActivityDetection  . . . . . . . . . . . . .  56
     5.4.  Modifying an Offer or Answer  . . . . . . . . . . . . . .  56
     5.5.  Processing a Local Description  . . . . . . . . . . . . .  57
     5.6.  Processing a Remote Description . . . . . . . . . . . . .  58
     5.7.  Processing a Rollback . . . . . . . . . . . . . . . . . .  58
     5.8.  Parsing a Session Description . . . . . . . . . . . . . .  59
       5.8.1.  Session-Level Parsing . . . . . . . . . . . . . . . .  59
       5.8.2.  Media Section Parsing . . . . . . . . . . . . . . . .  61
       5.8.3.  Semantics Verification  . . . . . . . . . . . . . . .  64
     5.9.  Applying a Local Description  . . . . . . . . . . . . . .  65
     5.10. Applying a Remote Description . . . . . . . . . . . . . .  66
     5.11. Applying an Answer  . . . . . . . . . . . . . . . . . . .  70
   6.  Processing RTP/RTCP . . . . . . . . . . . . . . . . . . . . .  73
   7.  Examples  . . . . . . . . . . . . . . . . . . . . . . . . . .  73
     7.1.  Simple Example  . . . . . . . . . . . . . . . . . . . . .  74
     7.2.  Detailed Example  . . . . . . . . . . . . . . . . . . . .  78
     7.3.  Early Transport Warmup Example  . . . . . . . . . . . . .  88
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  95
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  96
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  96
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  96
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  96
     11.2.  Informative References . . . . . . . . . . . . . . . . . 101
   Appendix A.  Appendix A . . . . . . . . . . . . . . . . . . . . . 103



Uberti, et al.            Expires March 5, 2018                 [Page 3]


Internet-Draft                    JSEP                    September 2017


   Appendix B.  Change log . . . . . . . . . . . . . . . . . . . . . 104
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . . 114

1.  Introduction

   This document describes how the W3C WEBRTC RTCPeerConnection
   interface [W3C.webrtc] is used to control the setup, management and
   teardown of a multimedia session.

1.1.  General Design of JSEP

   WebRTC call setup has been designed to focus on controlling the media
   plane, leaving signaling plane behavior up to the application as much
   as possible.  The rationale is that different applications may prefer
   to use different protocols, such as the existing SIP call signaling
   protocol, or something custom to the particular application, perhaps
   for a novel use case.  In this approach, the key information that
   needs to be exchanged is the multimedia session description, which
   specifies the necessary transport and media configuration information
   necessary to establish the media plane.

   With these considerations in mind, this document describes the
   JavaScript Session Establishment Protocol (JSEP) that allows for full
   control of the signaling state machine from JavaScript.  As described
   above, JSEP assumes a model in which a JavaScript application
   executes inside a runtime containing WebRTC APIs (the "JSEP
   implementation").  The JSEP implementation is almost entirely
   divorced from the core signaling flow, which is instead handled by
   the JavaScript making use of two interfaces: (1) passing in local and
   remote session descriptions and (2) interacting with the ICE state
   machine.  The combination of the JSEP implementation and the
   JavaScript application is referred to throughout this document as a
   "JSEP endpoint".

   In this document, the use of JSEP is described as if it always occurs
   between two JSEP endpoints.  Note though in many cases it will
   actually be between a JSEP endpoint and some kind of server, such as
   a gateway or MCU.  This distinction is invisible to the JSEP
   endpoint; it just follows the instructions it is given via the API.

   JSEP's handling of session descriptions is simple and
   straightforward.  Whenever an offer/answer exchange is needed, the
   initiating side creates an offer by calling a createOffer() API.  The
   application then uses that offer to set up its local config via the
   setLocalDescription() API.  The offer is finally sent off to the
   remote side over its preferred signaling mechanism (e.g.,
   WebSockets); upon receipt of that offer, the remote party installs it
   using the setRemoteDescription() API.



Uberti, et al.            Expires March 5, 2018                 [Page 4]


Internet-Draft                    JSEP                    September 2017


   To complete the offer/answer exchange, the remote party uses the
   createAnswer() API to generate an appropriate answer, applies it
   using the setLocalDescription() API, and sends the answer back to the
   initiator over the signaling channel.  When the initiator gets that
   answer, it installs it using the setRemoteDescription() API, and
   initial setup is complete.  This process can be repeated for
   additional offer/answer exchanges.

   Regarding ICE [RFC5245], JSEP decouples the ICE state machine from
   the overall signaling state machine, as the ICE state machine must
   remain in the JSEP implementation, because only the implementation
   has the necessary knowledge of candidates and other transport
   information.  Performing this separation provides additional
   flexibility in protocols that decouple session descriptions from
   transport.  For instance, in traditional SIP, each offer or answer is
   self-contained, including both the session descriptions and the
   transport information.  However, [I-D.ietf-mmusic-trickle-ice-sip]
   allows SIP to be used with trickle ICE [I-D.ietf-ice-trickle], in
   which the session description can be sent immediately and the
   transport information can be sent when available.  Sending transport
   information separately can allow for faster ICE and DTLS startup,
   since ICE checks can start as soon as any transport information is
   available rather than waiting for all of it.  JSEP's decoupling of
   the ICE and signaling state machines allows it to accommodate either
   model.

   Through its abstraction of signaling, the JSEP approach does require
   the application to be aware of the signaling process.  While the
   application does not need to understand the contents of session
   descriptions to set up a call, the application must call the right
   APIs at the right times, convert the session descriptions and ICE
   information into the defined messages of its chosen signaling
   protocol, and perform the reverse conversion on the messages it
   receives from the other side.

   One way to make life easier for the application is to provide a
   JavaScript library that hides this complexity from the developer;
   said library would implement a given signaling protocol along with
   its state machine and serialization code, presenting a higher level
   call-oriented interface to the application developer.  For example,
   libraries exist to adapt the JSEP API into an API suitable for a SIP
   or XMPP.  Thus, JSEP provides greater control for the experienced
   developer without forcing any additional complexity on the novice
   developer.







Uberti, et al.            Expires March 5, 2018                 [Page 5]


Internet-Draft                    JSEP                    September 2017


1.2.  Other Approaches Considered

   One approach that was considered instead of JSEP was to include a
   lightweight signaling protocol.  Instead of providing session
   descriptions to the API, the API would produce and consume messages
   from this protocol.  While providing a more high-level API, this put
   more control of signaling within the JSEP implementation, forcing it
   to have to understand and handle concepts like signaling glare (see
   [RFC3264], Section 4).

   A second approach that was considered but not chosen was to decouple
   the management of the media control objects from session
   descriptions, instead offering APIs that would control each component
   directly.  This was rejected based on the argument that requiring
   exposure of this level of complexity to the application programmer
   would not be beneficial; it would result in an API where even a
   simple example would require a significant amount of code to
   orchestrate all the needed interactions, as well as creating a large
   API surface that needed to be agreed upon and documented.  In
   addition, these API points could be called in any order, resulting in
   a more complex set of interactions with the media subsystem than the
   JSEP approach, which specifies how session descriptions are to be
   evaluated and applied.

   One variation on JSEP that was considered was to keep the basic
   session description-oriented API, but to move the mechanism for
   generating offers and answers out of the JSEP implementation.
   Instead of providing createOffer/createAnswer methods within the
   implementation, this approach would instead expose a getCapabilities
   API which would provide the application with the information it
   needed in order to generate its own session descriptions.  This
   increases the amount of work that the application needs to do; it
   needs to know how to generate session descriptions from capabilities,
   and especially how to generate the correct answer from an arbitrary
   offer and the supported capabilities.  While this could certainly be
   addressed by using a library like the one mentioned above, it
   basically forces the use of said library even for a simple example.
   Providing createOffer/createAnswer avoids this problem.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].







Uberti, et al.            Expires March 5, 2018                 [Page 6]


Internet-Draft                    JSEP                    September 2017


3.  Semantics and Syntax

3.1.  Signaling Model

   JSEP does not specify a particular signaling model or state machine,
   other than the generic need to exchange session descriptions in the
   fashion described by [RFC3264] (offer/answer) in order for both sides
   of the session to know how to conduct the session.  JSEP provides
   mechanisms to create offers and answers, as well as to apply them to
   a session.  However, the JSEP implementation is totally decoupled
   from the actual mechanism by which these offers and answers are
   communicated to the remote side, including addressing,
   retransmission, forking, and glare handling.  These issues are left
   entirely up to the application; the application has complete control
   over which offers and answers get handed to the implementation, and
   when.


       +-----------+                               +-----------+
       |  Web App  |<--- App-Specific Signaling -->|  Web App  |
       +-----------+                               +-----------+
             ^                                            ^
             |  SDP                                       |  SDP
             V                                            V
       +-----------+                                +-----------+
       |   JSEP    |<----------- Media ------------>|   JSEP    |
       |   Impl.   |                                |   Impl.   |
       +-----------+                                +-----------+


                      Figure 1: JSEP Signaling Model

3.2.  Session Descriptions and State Machine

   In order to establish the media plane, the JSEP implementation needs
   specific parameters to indicate what to transmit to the remote side,
   as well as how to handle the media that is received.  These
   parameters are determined by the exchange of session descriptions in
   offers and answers, and there are certain details to this process
   that must be handled in the JSEP APIs.

   Whether a session description applies to the local side or the remote
   side affects the meaning of that description.  For example, the list
   of codecs sent to a remote party indicates what the local side is
   willing to receive, which, when intersected with the set of codecs
   the remote side supports, specifies what the remote side should send.
   However, not all parameters follow this rule; some parameters are
   declarative and the remote side MUST either accept them or reject



Uberti, et al.            Expires March 5, 2018                 [Page 7]


Internet-Draft                    JSEP                    September 2017


   them altogether.  An example of such a parameter is the DTLS
   fingerprints [RFC8122], which are calculated based on the local
   certificate(s) offered, and are not subject to negotiation.

   In addition, various RFCs put different conditions on the format of
   offers versus answers.  For example, an offer may propose an
   arbitrary number of m= sections (i.e., media descriptions as
   described in [RFC4566], Section 5.14), but an answer must contain the
   exact same number as the offer.

   Lastly, while the exact media parameters are only known only after an
   offer and an answer have been exchanged, the offerer may receive ICE
   checks, and possibly media (e.g., in the case of a re-offer after a
   connection has been established) before it receives an answer.  To
   properly process incoming media in this case, the offerer's media
   handler must be aware of the details of the offer before the answer
   arrives.

   Therefore, in order to handle session descriptions properly, the JSEP
   implementation needs:

   1.  To know if a session description pertains to the local or remote
       side.

   2.  To know if a session description is an offer or an answer.

   3.  To allow the offer to be specified independently of the answer.

   JSEP addresses this by adding both setLocalDescription and
   setRemoteDescription methods and having session description objects
   contain a type field indicating the type of session description being
   supplied.  This satisfies the requirements listed above for both the
   offerer, who first calls setLocalDescription(sdp [offer]) and then
   later setRemoteDescription(sdp [answer]), as well as for the
   answerer, who first calls setRemoteDescription(sdp [offer]) and then
   later setLocalDescription(sdp [answer]).

   During the offer/answer exchange, the outstanding offer is considered
   to be "pending" at the offerer and the answerer, as it may either be
   accepted or rejected.  If this is a re-offer, each side will also
   have "current" local and remote descriptions, which reflect the
   result of the last offer/answer exchange.  Sections Section 4.1.12,
   Section 4.1.14, Section 4.1.11, and Section 4.1.13, provide more
   detail on pending and current descriptions.

   JSEP also allows for an answer to be treated as provisional by the
   application.  Provisional answers provide a way for an answerer to
   communicate initial session parameters back to the offerer, in order



Uberti, et al.            Expires March 5, 2018                 [Page 8]


Internet-Draft                    JSEP                    September 2017


   to allow the session to begin, while allowing a final answer to be
   specified later.  This concept of a final answer is important to the
   offer/answer model; when such an answer is received, any extra
   resources allocated by the caller can be released, now that the exact
   session configuration is known.  These "resources" can include things
   like extra ICE components, TURN candidates, or video decoders.
   Provisional answers, on the other hand, do no such deallocation; as a
   result, multiple dissimilar provisional answers, with their own codec
   choices, transport parameters, etc., can be received and applied
   during call setup.  Note that the final answer itself may be
   different than any received provisional answers.

   In [RFC3264], the constraint at the signaling level is that only one
   offer can be outstanding for a given session, but at the media stack
   level, a new offer can be generated at any point.  For example, when
   using SIP for signaling, if one offer is sent, then cancelled using a
   SIP CANCEL, another offer can be generated even though no answer was
   received for the first offer.  To support this, the JSEP media layer
   can provide an offer via the createOffer() method whenever the
   JavaScript application needs one for the signaling.  The answerer can
   send back zero or more provisional answers, and finally end the
   offer-answer exchange by sending a final answer.  The state machine
   for this is as follows:




























Uberti, et al.            Expires March 5, 2018                 [Page 9]


Internet-Draft                    JSEP                    September 2017


                       setRemote(OFFER)               setLocal(PRANSWER)
                           /-----\                               /-----\
                           |     |                               |     |
                           v     |                               v     |
            +---------------+    |                +---------------+    |
            |               |----/                |               |----/
            |  have-        | setLocal(PRANSWER)  | have-         |
            |  remote-offer |------------------- >| local-pranswer|
            |               |                     |               |
            |               |                     |               |
            +---------------+                     +---------------+
                 ^   |                                   |
                 |   | setLocal(ANSWER)                  |
   setRemote(OFFER)  |                                   |
                 |   V                  setLocal(ANSWER) |
            +---------------+                            |
            |               |                            |
            |               |<---------------------------+
            |    stable     |
            |               |<---------------------------+
            |               |                            |
            +---------------+          setRemote(ANSWER) |
                 ^   |                                   |
                 |   | setLocal(OFFER)                   |
   setRemote(ANSWER) |                                   |
                 |   V                                   |
            +---------------+                     +---------------+
            |               |                     |               |
            |  have-        | setRemote(PRANSWER) |have-          |
            |  local-offer  |------------------- >|remote-pranswer|
            |               |                     |               |
            |               |----\                |               |----\
            +---------------+    |                +---------------+    |
                           ^     |                               ^     |
                           |     |                               |     |
                           \-----/                               \-----/
                       setLocal(OFFER)               setRemote(PRANSWER)


                       Figure 2: JSEP State Machine

   Aside from these state transitions there is no other difference
   between the handling of provisional ("pranswer") and final ("answer")
   answers.







Uberti, et al.            Expires March 5, 2018                [Page 10]


Internet-Draft                    JSEP                    September 2017


3.3.  Session Description Format

   JSEP's session descriptions use SDP syntax for their internal
   representation.  While this format is not optimal for manipulation
   from JavaScript, it is widely accepted, and frequently updated with
   new features; any alternate encoding of session descriptions would
   have to keep pace with the changes to SDP, at least until the time
   that this new encoding eclipsed SDP in popularity.

   However, to provide for future flexibility, the SDP syntax is
   encapsulated within a SessionDescription object, which can be
   constructed from SDP, and be serialized out to SDP.  If future
   specifications agree on a JSON format for session descriptions, we
   could easily enable this object to generate and consume that JSON.

   As detailed below, most applications should be able to treat the
   SessionDescriptions produced and consumed by these various API calls
   as opaque blobs; that is, the application will not need to read or
   change them.

3.4.  Session Description Control

   In order to give the application control over various common session
   parameters, JSEP provides control surfaces which tell the JSEP
   implementation how to generate session descriptions.  This avoids the
   need for JavaScript to modify session descriptions in most cases.

   Changes to these objects result in changes to the session
   descriptions generated by subsequent createOffer/Answer calls.

3.4.1.  RtpTransceivers

   RtpTransceivers allow the application to control the RTP media
   associated with one m= section.  Each RtpTransceiver has an RtpSender
   and an RtpReceiver, which an application can use to control the
   sending and receiving of RTP media.  The application may also modify
   the RtpTransceiver directly, for instance, by stopping it.

   RtpTransceivers generally have a 1:1 mapping with m= sections,
   although there may be more RtpTransceivers than m= sections when
   RtpTransceivers are created but not yet associated with a m= section,
   or if RtpTransceivers have been stopped and disassociated from m=
   sections.  An RtpTransceiver is said to be associated with an m=
   section if its mid property is non-null; otherwise it is said to be
   disassociated.  The associated m= section is determined using a
   mapping between transceivers and m= section indices, formed when
   creating an offer or applying a remote offer.




Uberti, et al.            Expires March 5, 2018                [Page 11]


Internet-Draft                    JSEP                    September 2017


   An RtpTransceiver is never associated with more than one m= section,
   and once a session description is applied, a m= section is always
   associated with exactly one RtpTransceiver.  However, in certain
   cases where a m= section has been rejected, as discussed in
   Section 5.2.2 below, that m= section will be "recycled" and
   associated with a new RtpTransceiver with a new mid value.

   RtpTransceivers can be created explicitly by the application or
   implicitly by calling setRemoteDescription with an offer that adds
   new m= sections.

3.4.2.  RtpSenders

   RtpSenders allow the application to control how RTP media is sent.
   An RtpSender is conceptually responsible for the outgoing RTP
   stream(s) described by an m= section.  This includes encoding the
   attached MediaStreamTrack, sending RTP media packets, and generating/
   processing RTCP for the outgoing RTP streams(s).

3.4.3.  RtpReceivers

   RtpReceivers allow the application to inspect how RTP media is
   received.  An RtpReceiver is conceptually responsible for the
   incoming RTP stream(s) described by an m= section.  This includes
   processing received RTP media packets, decoding the incoming
   stream(s) to produce a remote MediaStreamTrack, and generating/
   processing RTCP for the incoming RTP stream(s).

3.5.  ICE

3.5.1.  ICE Gathering Overview

   JSEP gathers ICE candidates as needed by the application.  Collection
   of ICE candidates is referred to as a gathering phase, and this is
   triggered either by the addition of a new or recycled m= section to
   the local session description, or new ICE credentials in the
   description, indicating an ICE restart.  Use of new ICE credentials
   can be triggered explicitly by the application, or implicitly by the
   JSEP implementation in response to changes in the ICE configuration.

   When the ICE configuration changes in a way that requires a new
   gathering phase, a 'needs-ice-restart' bit is set.  When this bit is
   set, calls to the createOffer API will generate new ICE credentials.
   This bit is cleared by a call to the setLocalDescription API with new
   ICE credentials from either an offer or an answer, i.e., from either
   a local- or remote-initiated ICE restart.





Uberti, et al.            Expires March 5, 2018                [Page 12]


Internet-Draft                    JSEP                    September 2017


   When a new gathering phase starts, the ICE agent will notify the
   application that gathering is occurring through an event.  Then, when
   each new ICE candidate becomes available, the ICE agent will supply
   it to the application via an additional event; these candidates will
   also automatically be added to the current and/or pending local
   session description.  Finally, when all candidates have been
   gathered, an event will be dispatched to signal that the gathering
   process is complete.

   Note that gathering phases only gather the candidates needed by
   new/recycled/restarting m= sections; other m= sections continue to
   use their existing candidates.  Also, if an m= section is bundled
   (either by a successful bundle negotiation or by being marked as
   bundle-only), then candidates will be gathered and exchanged for that
   m= section if and only if its MID is a BUNDLE-tag, as described in
   [I-D.ietf-mmusic-sdp-bundle-negotiation].

3.5.2.  ICE Candidate Trickling

   Candidate trickling is a technique through which a caller may
   incrementally provide candidates to the callee after the initial
   offer has been dispatched; the semantics of "Trickle ICE" are defined
   in [I-D.ietf-ice-trickle].  This process allows the callee to begin
   acting upon the call and setting up the ICE (and perhaps DTLS)
   connections immediately, without having to wait for the caller to
   gather all possible candidates.  This results in faster media setup
   in cases where gathering is not performed prior to initiating the
   call.

   JSEP supports optional candidate trickling by providing APIs, as
   described above, that provide control and feedback on the ICE
   candidate gathering process.  Applications that support candidate
   trickling can send the initial offer immediately and send individual
   candidates when they get the notified of a new candidate;
   applications that do not support this feature can simply wait for the
   indication that gathering is complete, and then create and send their
   offer, with all the candidates, at this time.

   Upon receipt of trickled candidates, the receiving application will
   supply them to its ICE agent.  This triggers the ICE agent to start
   using the new remote candidates for connectivity checks.

3.5.2.1.  ICE Candidate Format

   In JSEP, ICE candidates are abstracted by an IceCandidate object, and
   as with session descriptions, SDP syntax is used for the internal
   representation.




Uberti, et al.            Expires March 5, 2018                [Page 13]


Internet-Draft                    JSEP                    September 2017


   The candidate details are specified in an IceCandidate field, using
   the same SDP syntax as the "candidate-attribute" field defined in
   [RFC5245], Section 15.1.  Note that this field does not contain an
   "a=" prefix, as indicated in the following example:


   candidate:1 1 UDP 1694498815 192.0.2.33 10000 typ host


   The IceCandidate object contains a field to indicate which ICE ufrag
   it is associated with, as defined in [RFC5245], Section 15.4.  This
   value is used to determine which session description (and thereby
   which gathering phase) this IceCandidate belongs to, which helps
   resolve ambiguities during ICE restarts.  If this field is absent in
   a received IceCandidate (perhaps when communicating with a non-JSEP
   endpoint), the most recently received session description is assumed.

   The IceCandidate object also contains fields to indicate which m=
   section it is associated with, which can be identified in one of two
   ways, either by a m= section index, or a MID.  The m= section index
   is a zero-based index, with index N referring to the N+1th m= section
   in the session description referenced by this IceCandidate.  The MID
   is a "media stream identification" value, as defined in [RFC5888],
   Section 4, which provides a more robust way to identify the m=
   section in the session description, using the MID of the associated
   RtpTransceiver object (which may have been locally generated by the
   answerer when interacting with a non-JSEP endpoint that does not
   support the MID attribute, as discussed in Section 5.10 below).  If
   the MID field is present in a received IceCandidate, it MUST be used
   for identification; otherwise, the m= section index is used instead.

   When creating an IceCandidate object, JSEP implementations MUST
   populate each of the candidate, ufrag, m= section index, and MID
   fields.  Implementations MUST also be prepared to receive objects
   with some fields missing, as mentioned above.

3.5.3.  ICE Candidate Policy

   Typically, when gathering ICE candidates, the JSEP implementation
   will gather all possible forms of initial candidates - host, server
   reflexive, and relay.  However, in certain cases, applications may
   want to have more specific control over the gathering process, due to
   privacy or related concerns.  For example, one may want to only use
   relay candidates, to leak as little location information as possible
   (keeping in mind that this choice comes with corresponding
   operational costs).  To accomplish this, JSEP allows the application
   to restrict which ICE candidates are used in a session.  Note that
   this filtering is applied on top of any restrictions the



Uberti, et al.            Expires March 5, 2018                [Page 14]


Internet-Draft                    JSEP                    September 2017


   implementation chooses to enforce regarding which IP addresses are
   permitted for the application, as discussed in
   [I-D.ietf-rtcweb-ip-handling].

   There may also be cases where the application wants to change which
   types of candidates are used while the session is active.  A prime
   example is where a callee may initially want to use only relay
   candidates, to avoid leaking location information to an arbitrary
   caller, but then change to use all candidates (for lower operational
   cost) once the user has indicated they want to take the call.  For
   this scenario, the JSEP implementation MUST allow the candidate
   policy to be changed in mid-session, subject to the aforementioned
   interactions with local policy.

   To administer the ICE candidate policy, the JSEP implementation will
   determine the current setting at the start of each gathering phase.
   Then, during the gathering phase, the implementation MUST NOT expose
   candidates disallowed by the current policy to the application, use
   them as the source of connectivity checks, or indirectly expose them
   via other fields, such as the raddr/rport attributes for other ICE
   candidates.  Later, if a different policy is specified by the
   application, the application can apply it by kicking off a new
   gathering phase via an ICE restart.

3.5.4.  ICE Candidate Pool

   JSEP applications typically inform the JSEP implementation to begin
   ICE gathering via the information supplied to setLocalDescription, as
   the local description indicates the number of ICE components which
   will be needed and for which candidates must be gathered.  However,
   to accelerate cases where the application knows the number of ICE
   components to use ahead of time, it may ask the implementation to
   gather a pool of potential ICE candidates to help ensure rapid media
   setup.

   When setLocalDescription is eventually called, and the JSEP
   implementation goes to gather the needed ICE candidates, it SHOULD
   start by checking if any candidates are available in the pool.  If
   there are candidates in the pool, they SHOULD be handed to the
   application immediately via the ICE candidate event.  If the pool
   becomes depleted, either because a larger-than-expected number of ICE
   components is used, or because the pool has not had enough time to
   gather candidates, the remaining candidates are gathered as usual.
   This only occurs for the first offer/answer exchange, after which the
   candidate pool is emptied and no longer used.

   One example of where this concept is useful is an application that
   expects an incoming call at some point in the future, and wants to



Uberti, et al.            Expires March 5, 2018                [Page 15]


Internet-Draft                    JSEP                    September 2017


   minimize the time it takes to establish connectivity, to avoid
   clipping of initial media.  By pre-gathering candidates into the
   pool, it can exchange and start sending connectivity checks from
   these candidates almost immediately upon receipt of a call.  Note
   though that by holding on to these pre-gathered candidates, which
   will be kept alive as long as they may be needed, the application
   will consume resources on the STUN/TURN servers it is using.

3.6.  Video Size Negotiation

   Video size negotiation is the process through which a receiver can
   use the "a=imageattr" SDP attribute [RFC6236] to indicate what video
   frame sizes it is capable of receiving.  A receiver may have hard
   limits on what its video decoder can process, or it may have some
   maximum set by policy.  By specifying these limits in an
   "a=imageattr" attribute, JSEP endpoints can attempt to ensure that
   the remote sender transmits video at an acceptable resolution.
   However, when communicating with a non-JSEP endpoint that does not
   understand this attribute, any signaled limits may be exceeded, and
   the JSEP implementation MUST handle this gracefully, e.g., by
   discarding the video.

   Note that certain codecs support transmission of samples with aspect
   ratios other than 1.0 (i.e., non-square pixels).  JSEP
   implementations will not transmit non-square pixels, but SHOULD
   receive and render such video with the correct aspect ratio.
   However, sample aspect ratio has no impact on the size negotiation
   described below; all dimensions are measured in pixels, whether
   square or not.

3.6.1.  Creating an imageattr Attribute

   The receiver will first intersect any known local limits (e.g.,
   hardware decoder capababilities, local policy) to determine the
   absolute minimum and maximum sizes it can receive.  If there are no
   known local limits, the "a=imageattr" attribute SHOULD be omitted.
   If these local limits preclude receiving any video, i.e., the
   degenerate case of no permitted resolutions, the "a=imageattr"
   attribute MUST be omitted, and the m= section MUST be marked as
   sendonly/inactive, as appropriate.

   Otherwise, an "a=imageattr" attribute is created with "recv"
   direction, and the resulting resolution space formed from the
   aforementioned intersection is used to specify its minimum and
   maximum x= and y= values.






Uberti, et al.            Expires March 5, 2018                [Page 16]


Internet-Draft                    JSEP                    September 2017


   The rules here express a single set of preferences, and therefore,
   the "a=imageattr" q= value is not important.  It SHOULD be set to
   1.0.

   The "a=imageattr" field is payload type specific.  When all video
   codecs supported have the same capabilities, use of a single
   attribute, with the wildcard payload type (*), is RECOMMENDED.
   However, when the supported video codecs have different limitations,
   specific "a=imageattr" attributes MUST be inserted for each payload
   type.

   As an example, consider a system with a multiformat video decoder,
   which is capable of decoding any resolution from 48x48 to 720p, In
   this case, the implementation would generate this attribute:

   a=imageattr:* recv [x=[48:1280],y=[48:720],q=1.0]

   This declaration indicates that the receiver is capable of decoding
   any image resolution from 48x48 up to 1280x720 pixels.

3.6.2.  Interpreting imageattr Attributes

   [RFC6236] defines "a=imageattr" to be an advisory field.  This means
   that it does not absolutely constrain the video formats that the
   sender can use, but gives an indication of the preferred values.

   This specification prescribes more specific behavior.  When a
   MediaStreamTrack, which is producing video of a certain resolution
   (the "track resolution"), is attached to a RtpSender, which is
   encoding the track video at the same or lower resolution(s) (the
   "encoder resolutions"), and a remote description is applied that
   references the sender and contains valid "a=imageattr recv"
   attributes, it MUST follow the rules below to ensure the sender does
   not transmit a resolution that would exceed the size criteria
   specified in the attributes.  These rules MUST be followed as long as
   the attributes remain present in the remote description, including
   cases in which the track changes its resolution, or is replaced with
   a different track.

   Depending on how the RtpSender is configured, it may be producing a
   single encoding at a certain resolution, or, if simulcast Section 3.7
   has been negotiated, multiple encodings, each at their own specific
   resolution.  In addition, depending on the configuration, each
   encoding may have the flexibility to reduce resolution when needed,
   or may be locked to a specific output resolution.

   For each encoding being produced by the RtpSender, the set of
   "a=imageattr recv" attributes in the corresponding m= section of the



Uberti, et al.            Expires March 5, 2018                [Page 17]


Internet-Draft                    JSEP                    September 2017


   remote description is processed to determine what should be
   transmitted.  Only attributes that reference the media format
   selected for the encoding are considered; each such attribute is
   evaluated individually, starting with the attribute with the highest
   "q=" value.  If multiple attributes have the same "q=" value, they
   are evaluated in the order they appear in their containing m=
   section.  Note that while JSEP endpoints will include at most one
   "a=imageattr recv" attribute per media format, JSEP endpoints may
   receive session descriptions from non-JSEP endpoints with m= sections
   that contain multiple such attributes.

   For each "a=imageattr recv" attribute, the following rules are
   applied.  If this processing is successful, the encoding is
   transmitted accordingly, and no further attributes are considered for
   that encoding.  Otherwise, the next attribute is evaluated, in the
   aforementioned order.  If none of the supplied attributes can be
   processed successfully, the encoding MUST NOT be transmitted, and an
   error SHOULD be raised to the application.

   o  The limits from the attribute are compared to the encoder
      resolution.  Only the specific limits mentioned below are
      considered; any other values, such as picture aspect ratio, MUST
      be ignored.  When considering a MediaStreamTrack that is producing
      rotated video, the unrotated resolution MUST be used for the
      checks.  This is required regardless of whether the receiver
      supports performing receive-side rotation (e.g., through CVO
      [TS26.114]), as it significantly simplifies the matching logic.

   o  If the attribute includes a "sar=" (sample aspect ratio) value set
      to something other than "1.0", indicating the receiver wants to
      receive non-square pixels, this cannot be satisfied and the
      attribute MUST NOT be used.

   o  If the encoder resolution exceeds the maximum size permitted by
      the attribute, and the encoder is allowed to adjust its
      resolution, the encoder SHOULD apply downscaling in order to
      satisfy the limits, although the downscaling MUST NOT change the
      picture aspect ratio of the encoding.  For example, if the encoder
      resolution is 1280x720, and the attribute specified a maximum of
      640x480, the expected output resolution would be 640x360.  If
      downscaling cannot be applied, the attribute MUST NOT be used.

   o  If the encoder resolution is less than the minimum size permitted
      by the attribute, the attribute MUST NOT be used; the encoder MUST
      NOT apply upscaling.  JSEP implementations SHOULD avoid this
      situation by allowing receipt of arbitrarily small resolutions,
      perhaps via fallback to a software decoder.




Uberti, et al.            Expires March 5, 2018                [Page 18]


Internet-Draft                    JSEP                    September 2017


   o  If the encoder resolution is within the maximum and minimum sizes,
      no action is needed.

3.7.  Simulcast

   JSEP supports simulcast transmission of a MediaStreamTrack, where
   multiple encodings of the source media can be transmitted within the
   context of a single m= section.  The current JSEP API is designed to
   allow applications to send simulcasted media but only to receive a
   single encoding.  This allows for multi-user scenarios where each
   sending client sends multiple encodings to a server, which then, for
   each receiving client, chooses the appropriate encoding to forward.

   Applications request support for simulcast by configuring multiple
   encodings on an RtpSender.  Upon generation of an offer or answer,
   these encodings are indicated via SDP markings on the corresponding
   m= section, as described below.  Receivers that understand simulcast
   and are willing to receive it will also include SDP markings to
   indicate their support, and JSEP endpoints will use these markings to
   determine whether simulcast is permitted for a given RtpSender.  If
   simulcast support is not negotiated, the RtpSender will only use the
   first configured encoding.

   Note that the exact simulcast parameters are up to the sending
   application.  While the aforementioned SDP markings are provided to
   ensure the remote side can receive and demux multiple simulcast
   encodings, the specific resolutions and bitrates to be used for each
   encoding are purely a send-side decision in JSEP.

   JSEP currently does not provide a mechanism to configure receipt of
   simulcast.  This means that if simulcast is offered by the remote
   endpoint, the answer generated by a JSEP endpoint will not indicate
   support for receipt of simulcast, and as such the remote endpoint
   will only send a single encoding per m= section.

   In addition, JSEP does not provide a mechanism to handle an incoming
   offer requesting simulcast from the JSEP endpoint.  This means that
   setting up simulcast in the case where the JSEP endpoint receives the
   initial offer requires out-of-band signaling or SDP inspection.
   However, in the case where the JSEP endpoint sets up simulcast in its
   in initial offer, any established simulcast streams will continue to
   work upon receipt of an incoming re-offer.  Future versions of this
   specification may add additional APIs to handle the incoming initial
   offer scenario.

   When using JSEP to transmit multiple encodings from a RtpSender, the
   techniques from [I-D.ietf-mmusic-sdp-simulcast] and
   [I-D.ietf-mmusic-rid] are used.  Specifically, when multiple



Uberti, et al.            Expires March 5, 2018                [Page 19]


Internet-Draft                    JSEP                    September 2017


   encodings have been configured for a RtpSender, the m= section for
   the RtpSender will include an "a=simulcast" attribute, as defined in
   [I-D.ietf-mmusic-sdp-simulcast], Section 6.2, with a "send" simulcast
   stream description that lists each desired encoding, and no "recv"
   simulcast stream description.  The m= section will also include an
   "a=rid" attribute for each encoding, as specified in
   [I-D.ietf-mmusic-rid], Section 4; the use of RID identifiers allows
   the individual encodings to be disambiguated even though they are all
   part of the same m= section.

3.8.  Interactions With Forking

   Some call signaling systems allow various types of forking where an
   SDP Offer may be provided to more than one device.  For example, SIP
   [RFC3261] defines both a "Parallel Search" and "Sequential Search".
   Although these are primarily signaling level issues that are outside
   the scope of JSEP, they do have some impact on the configuration of
   the media plane that is relevant.  When forking happens at the
   signaling layer, the JavaScript application responsible for the
   signaling needs to make the decisions about what media should be sent
   or received at any point of time, as well as which remote endpoint it
   should communicate with; JSEP is used to make sure the media engine
   can make the RTP and media perform as required by the application.
   The basic operations that the applications can have the media engine
   do are:

   o  Start exchanging media with a given remote peer, but keep all the
      resources reserved in the offer.

   o  Start exchanging media with a given remote peer, and free any
      resources in the offer that are not being used.

3.8.1.  Sequential Forking

   Sequential forking involves a call being dispatched to multiple
   remote callees, where each callee can accept the call, but only one
   active session ever exists at a time; no mixing of received media is
   performed.

   JSEP handles sequential forking well, allowing the application to
   easily control the policy for selecting the desired remote endpoint.
   When an answer arrives from one of the callees, the application can
   choose to apply it either as a provisional answer, leaving open the
   possibility of using a different answer in the future, or apply it as
   a final answer, ending the setup flow.






Uberti, et al.            Expires March 5, 2018                [Page 20]


Internet-Draft                    JSEP                    September 2017


   In a "first-one-wins" situation, the first answer will be applied as
   a final answer, and the application will reject any subsequent
   answers.  In SIP parlance, this would be ACK + BYE.

   In a "last-one-wins" situation, all answers would be applied as
   provisional answers, and any previous call leg will be terminated.
   At some point, the application will end the setup process, perhaps
   with a timer; at this point, the application could reapply the
   pending remote description as a final answer.

3.8.2.  Parallel Forking

   Parallel forking involves a call being dispatched to multiple remote
   callees, where each callee can accept the call, and multiple
   simultaneous active signaling sessions can be established as a
   result.  If multiple callees send media at the same time, the
   possibilities for handling this are described in [RFC3960],
   Section 3.1.  Most SIP devices today only support exchanging media
   with a single device at a time, and do not try to mix multiple early
   media audio sources, as that could result in a confusing situation.
   For example, consider having a European ringback tone mixed together
   with the North American ringback tone - the resulting sound would not
   be like either tone, and would confuse the user.  If the signaling
   application wishes to only exchange media with one of the remote
   endpoints at a time, then from a media engine point of view, this is
   exactly like the sequential forking case.

   In the parallel forking case where the JavaScript application wishes
   to simultaneously exchange media with multiple peers, the flow is
   slightly more complex, but the JavaScript application can follow the
   strategy that [RFC3960] describes using UPDATE.  The UPDATE approach
   allows the signaling to set up a separate media flow for each peer
   that it wishes to exchange media with.  In JSEP, this offer used in
   the UPDATE would be formed by simply creating a new PeerConnection
   (see Section 4.1) and making sure that the same local media streams
   have been added into this new PeerConnection.  Then the new
   PeerConnection object would produce a SDP offer that could be used by
   the signaling to perform the UPDATE strategy discussed in [RFC3960].

   As a result of sharing the media streams, the application will end up
   with N parallel PeerConnection sessions, each with a local and remote
   description and their own local and remote addresses.  The media flow
   from these sessions can be managed using setDirection (see
   Section 4.2.3), or the application can choose to play out the media
   from all sessions mixed together.  Of course, if the application
   wants to only keep a single session, it can simply terminate the
   sessions that it no longer needs.




Uberti, et al.            Expires March 5, 2018                [Page 21]


Internet-Draft                    JSEP                    September 2017


4.  Interface

   This section details the basic operations that must be present to
   implement JSEP functionality.  The actual API exposed in the W3C API
   may have somewhat different syntax, but should map easily to these
   concepts.

4.1.  PeerConnection

4.1.1.  Constructor

   The PeerConnection constructor allows the application to specify
   global parameters for the media session, such as the STUN/TURN
   servers and credentials to use when gathering candidates, as well as
   the initial ICE candidate policy and pool size, and also the bundle
   policy to use.

   If an ICE candidate policy is specified, it functions as described in
   Section 3.5.3, causing the JSEP implementation to only surface the
   permitted candidates (including any implementation-internal
   filtering) to the application, and only use those candidates for
   connectivity checks.  The set of available policies is as follows:

   all:  All candidates permitted by implementation policy will be
      gathered and used.



   relay:  All candidates except relay candidates will be filtered out.
      This obfuscates the location information that might be ascertained
      by the remote peer from the received candidates.  Depending on how
      the application deploys and chooses relay servers, this could
      obfuscate location to a metro or possibly even global level.

   The default ICE candidate policy MUST be set to "all" as this is
   generally the desired policy, and also typically reduces use of
   application TURN server resources significantly.

   If a size is specified for the ICE candidate pool, this indicates the
   number of ICE components to pre-gather candidates for.  Because pre-
   gathering results in utilizing STUN/TURN server resources for
   potentially long periods of time, this must only occur upon
   application request, and therefore the default candidate pool size
   MUST be zero.

   The application can specify its preferred policy regarding use of
   bundle, the multiplexing mechanism defined in
   [I-D.ietf-mmusic-sdp-bundle-negotiation].  Regardless of policy, the



Uberti, et al.            Expires March 5, 2018                [Page 22]


Internet-Draft                    JSEP                    September 2017


   application will always try to negotiate bundle onto a single
   transport, and will offer a single bundle group across all m=
   sections; use of this single transport is contingent upon the
   answerer accepting bundle.  However, by specifying a policy from the
   list below, the application can control exactly how aggressively it
   will try to bundle media streams together, which affects how it will
   interoperate with a non-bundle-aware endpoint.  When negotiating with
   a non-bundle-aware endpoint, only the streams not marked as bundle-
   only streams will be established.

   The set of available policies is as follows:

   balanced:  The first m= section of each type (audio, video, or
      application) will contain transport parameters, which will allow
      an answerer to unbundle that section.  The second and any
      subsequent m= section of each type will be marked bundle-only.
      The result is that if there are N distinct media types, then
      candidates will be gathered for for N media streams.  This policy
      balances desire to multiplex with the need to ensure basic audio
      and video can still be negotiated in legacy cases.  When acting as
      answerer, if there is no bundle group in the offer, the
      implementation will reject all but the first m= section of each
      type.



   max-compat:  All m= sections will contain transport parameters; none
      will be marked as bundle-only.  This policy will allow all streams
      to be received by non-bundle-aware endpoints, but require separate
      candidates to be gathered for each media stream.



   max-bundle:  Only the first m= section will contain transport
      parameters; all streams other than the first will be marked as
      bundle-only.  This policy aims to minimize candidate gathering and
      maximize multiplexing, at the cost of less compatibility with
      legacy endpoints.  When acting as answerer, the implementation
      will reject any m= sections other than the first m= section,
      unless they are in the same bundle group as that m= section.

   As it provides the best tradeoff between performance and
   compatibility with legacy endpoints, the default bundle policy MUST
   be set to "balanced".

   The application can specify its preferred policy regarding use of
   RTP/RTCP multiplexing [RFC5761] using one of the following policies:




Uberti, et al.            Expires March 5, 2018                [Page 23]


Internet-Draft                    JSEP                    September 2017


   negotiate:  The JSEP implementation will gather both RTP and RTCP
      candidates but also will offer "a=rtcp-mux", thus allowing for
      compatibility with either multiplexing or non-multiplexing
      endpoints.

   require:  The JSEP implementation will only gather RTP candidates and
      will insert an "a=rtcp-mux-only" indication into any new m=
      sections in offers it generates.  This halves the number of
      candidates that the offerer needs to gather.  Applying a
      description with an m= section that does not contain an "a=rtcp-
      mux" attribute will cause an error to be returned.

   The default multiplexing policy MUST be set to "require".
   Implementations MAY choose to reject attempts by the application to
   set the multiplexing policy to "negotiate".

4.1.2.  addTrack

   The addTrack method adds a MediaStreamTrack to the PeerConnection,
   using the MediaStream argument to associate the track with other
   tracks in the same MediaStream, so that they can be added to the same
   "LS" group when creating an offer or answer.  Adding tracks to the
   same "LS" group indicates that the playback of these tracks should be
   synchronized for proper lip sync, as described in [RFC5888],
   Section 7.  addTrack attempts to minimize the number of transceivers
   as follows: If the PeerConnection is in the "have-remote-offer"
   state, the track will be attached to the first compatible transceiver
   that was created by the most recent call to setRemoteDescription()
   and does not have a local track.  Otherwise, a new transceiver will
   be created, as described in Section 4.1.4.

4.1.3.  removeTrack

   The removeTrack method removes a MediaStreamTrack from the
   PeerConnection, using the RtpSender argument to indicate which sender
   should have its track removed.  The sender's track is cleared, and
   the sender stops sending.  Future calls to createOffer will mark the
   m= section associated with the sender as recvonly (if
   transceiver.direction is sendrecv) or as inactive (if
   transceiver.direction is sendonly).

4.1.4.  addTransceiver

   The addTransceiver method adds a new RtpTransceiver to the
   PeerConnection.  If a MediaStreamTrack argument is provided, then the
   transceiver will be configured with that media type and the track
   will be attached to the transceiver.  Otherwise, the application MUST
   explicitly specify the type; this mode is useful for creating



Uberti, et al.            Expires March 5, 2018                [Page 24]


Internet-Draft                    JSEP                    September 2017


   recvonly transceivers as well as for creating transceivers to which a
   track can be attached at some later point.

   At the time of creation, the application can also specify a
   transceiver direction attribute, a set of MediaStreams which the
   transceiver is associated with (allowing LS group assignments), and a
   set of encodings for the media (used for simulcast as described in
   Section 3.7).

4.1.5.  createDataChannel

   The createDataChannel method creates a new data channel and attaches
   it to the PeerConnection.  If no data channel currently exists for
   this PeerConnection, then a new offer/answer exchange is required.
   All data channels on a given PeerConnection share the same SCTP/DTLS
   association and therefore the same m= section, so subsequent creation
   of data channels does not have any impact on the JSEP state.

   The createDataChannel method also includes a number of arguments
   which are used by the PeerConnection (e.g., maxPacketLifetime) but
   are not reflected in the SDP and do not affect the JSEP state.

4.1.6.  createOffer

   The createOffer method generates a blob of SDP that contains a
   [RFC3264] offer with the supported configurations for the session,
   including descriptions of the media added to this PeerConnection, the
   codec/RTP/RTCP options supported by this implementation, and any
   candidates that have been gathered by the ICE agent.  An options
   parameter may be supplied to provide additional control over the
   generated offer.  This options parameter allows an application to
   trigger an ICE restart, for the purpose of reestablishing
   connectivity.

   In the initial offer, the generated SDP will contain all desired
   functionality for the session (functionality that is supported but
   not desired by default may be omitted); for each SDP line, the
   generation of the SDP will follow the process defined for generating
   an initial offer from the document that specifies the given SDP line.
   The exact handling of initial offer generation is detailed in
   Section 5.2.1 below.

   In the event createOffer is called after the session is established,
   createOffer will generate an offer to modify the current session
   based on any changes that have been made to the session, e.g., adding
   or stopping RtpTransceivers, or requesting an ICE restart.  For each
   existing stream, the generation of each SDP line must follow the
   process defined for generating an updated offer from the RFC that



Uberti, et al.            Expires March 5, 2018                [Page 25]


Internet-Draft                    JSEP                    September 2017


   specifies the given SDP line.  For each new stream, the generation of
   the SDP must follow the process of generating an initial offer, as
   mentioned above.  If no changes have been made, or for SDP lines that
   are unaffected by the requested changes, the offer will only contain
   the parameters negotiated by the last offer-answer exchange.  The
   exact handling of subsequent offer generation is detailed in
   Section 5.2.2. below.

   Session descriptions generated by createOffer must be immediately
   usable by setLocalDescription; if a system has limited resources
   (e.g. a finite number of decoders), createOffer should return an
   offer that reflects the current state of the system, so that
   setLocalDescription will succeed when it attempts to acquire those
   resources.

   Calling this method may do things such as generating new ICE
   credentials, but does not change the PeerConnection state, trigger
   candidate gathering, or cause media to start or stop flowing.
   Specifically, the offer is not applied, and does not become the
   pending local description, until setLocalDescription is called.

4.1.7.  createAnswer

   The createAnswer method generates a blob of SDP that contains a
   [RFC3264] SDP answer with the supported configuration for the session
   that is compatible with the parameters supplied in the most recent
   call to setRemoteDescription, which MUST have been called prior to
   calling createAnswer.  Like createOffer, the returned blob contains
   descriptions of the media added to this PeerConnection, the
   codec/RTP/RTCP options negotiated for this session, and any
   candidates that have been gathered by the ICE agent.  An options
   parameter may be supplied to provide additional control over the
   generated answer.

   As an answer, the generated SDP will contain a specific configuration
   that specifies how the media plane should be established; for each
   SDP line, the generation of the SDP must follow the process defined
   for generating an answer from the document that specifies the given
   SDP line.  The exact handling of answer generation is detailed in
   Section 5.3. below.

   Session descriptions generated by createAnswer must be immediately
   usable by setLocalDescription; like createOffer, the returned
   description should reflect the current state of the system.

   Calling this method may do things such as generating new ICE
   credentials, but does not change the PeerConnection state, trigger
   candidate gathering, or or cause a media state change.  Specifically,



Uberti, et al.            Expires March 5, 2018                [Page 26]


Internet-Draft                    JSEP                    September 2017


   the answer is not applied, and does not become the current local
   description, until setLocalDescription is called.

4.1.8.  SessionDescriptionType

   Session description objects (RTCSessionDescription) may be of type
   "offer", "pranswer", "answer" or "rollback".  These types provide
   information as to how the description parameter should be parsed, and
   how the media state should be changed.

   "offer" indicates that a description should be parsed as an offer;
   said description may include many possible media configurations.  A
   description used as an "offer" may be applied anytime the
   PeerConnection is in a stable state, or as an update to a previously
   supplied but unanswered "offer".

   "pranswer" indicates that a description should be parsed as an
   answer, but not a final answer, and so should not result in the
   freeing of allocated resources.  It may result in the start of media
   transmission, if the answer does not specify an inactive media
   direction.  A description used as a "pranswer" may be applied as a
   response to an "offer", or an update to a previously sent "pranswer".

   "answer" indicates that a description should be parsed as an answer,
   the offer-answer exchange should be considered complete, and any
   resources (decoders, candidates) that are no longer needed can be
   released.  A description used as an "answer" may be applied as a
   response to an "offer", or an update to a previously sent "pranswer".

   The only difference between a provisional and final answer is that
   the final answer results in the freeing of any unused resources that
   were allocated as a result of the offer.  As such, the application
   can use some discretion on whether an answer should be applied as
   provisional or final, and can change the type of the session
   description as needed.  For example, in a serial forking scenario, an
   application may receive multiple "final" answers, one from each
   remote endpoint.  The application could choose to accept the initial
   answers as provisional answers, and only apply an answer as final
   when it receives one that meets its criteria (e.g. a live user
   instead of voicemail).

   "rollback" is a special session description type implying that the
   state machine should be rolled back to the previous stable state, as
   described in Section 4.1.8.2.  The contents MUST be empty.







Uberti, et al.            Expires March 5, 2018                [Page 27]


Internet-Draft                    JSEP                    September 2017


4.1.8.1.  Use of Provisional Answers

   Most applications will not need to create answers using the
   "pranswer" type.  While it is good practice to send an immediate
   response to an offer, in order to warm up the session transport and
   prevent media clipping, the preferred handling for a JSEP application
   is to create and send a "sendonly" final answer with a null
   MediaStreamTrack immediately after receiving the offer, which will
   prevent media from being sent by the caller, and allow media to be
   sent immediately upon answer by the callee.  Later, when the callee
   actually accepts the call, the application can plug in the real
   MediaStreamTrack and create a new "sendrecv" offer to update the
   previous offer/answer pair and start bidirectional media flow.  While
   this could also be done with a "sendonly" pranswer, followed by a
   "sendrecv" answer, the initial pranswer leaves the offer-answer
   exchange open, which means that the caller cannot send an updated
   offer during this time.

   As an example, consider a typical JSEP application that wants to set
   up audio and video as quickly as possible.  When the callee receives
   an offer with audio and video MediaStreamTracks, it will send an
   immediate answer accepting these tracks as sendonly (meaning that the
   caller will not send the callee any media yet, and because the callee
   has not yet added its own MediaStreamTracks, the callee will not send
   any media either).  It will then ask the user to accept the call and
   acquire the needed local tracks.  Upon acceptance by the user, the
   application will plug in the tracks it has acquired, which, because
   ICE and DTLS handshaking have likely completed by this point, can
   start transmitting immediately.  The application will also send a new
   offer to the remote side indicating call acceptance and moving the
   audio and video to be two-way media.  A detailed example flow along
   these lines is shown in Section 7.3.

   Of course, some applications may not be able to perform this double
   offer-answer exchange, particularly ones that are attempting to
   gateway to legacy signaling protocols.  In these cases, pranswer can
   still provide the application with a mechanism to warm up the
   transport.

4.1.8.2.  Rollback

   In certain situations it may be desirable to "undo" a change made to
   setLocalDescription or setRemoteDescription.  Consider a case where a
   call is ongoing, and one side wants to change some of the session
   parameters; that side generates an updated offer and then calls
   setLocalDescription.  However, the remote side, either before or
   after setRemoteDescription, decides it does not want to accept the
   new parameters, and sends a reject message back to the offerer.  Now,



Uberti, et al.            Expires March 5, 2018                [Page 28]


Internet-Draft                    JSEP                    September 2017


   the offerer, and possibly the answerer as well, need to return to a
   stable state and the previous local/remote description.  To support
   this, we introduce the concept of "rollback", which discards any
   proposed changes to the session, returning the state machine to the
   stable state.  A rollback is performed by supplying a session
   description of type "rollback" with empty contents to either
   setLocalDescription or setRemoteDescription.

4.1.9.  setLocalDescription

   The setLocalDescription method instructs the PeerConnection to apply
   the supplied session description as its local configuration.  The
   type field indicates whether the description should be processed as
   an offer, provisional answer, final answer, or rollback; offers and
   answers are checked differently, using the various rules that exist
   for each SDP line.

   This API changes the local media state; among other things, it sets
   up local resources for receiving and decoding media.  In order to
   successfully handle scenarios where the application wants to offer to
   change from one media format to a different, incompatible format, the
   PeerConnection must be able to simultaneously support use of both the
   current and pending local descriptions (e.g., support the codecs that
   exist in either description).  This dual processing begins when the
   PeerConnection enters the "have-local-offer" state, and continues
   until setRemoteDescription is called with either a final answer, at
   which point the PeerConnection can fully adopt the pending local
   description, or a rollback, which results in a revert to the current
   local description.

   This API indirectly controls the candidate gathering process.  When a
   local description is supplied, and the number of transports currently
   in use does not match the number of transports needed by the local
   description, the PeerConnection will create transports as needed and
   begin gathering candidates for each transport, using ones from the
   candidate pool if available.

   If setRemoteDescription was previously called with an offer, and
   setLocalDescription is called with an answer (provisional or final),
   and the media directions are compatible, and media is available to
   send, this will result in the starting of media transmission.

4.1.10.  setRemoteDescription

   The setRemoteDescription method instructs the PeerConnection to apply
   the supplied session description as the desired remote configuration.
   As in setLocalDescription, the type field of the description
   indicates how it should be processed.



Uberti, et al.            Expires March 5, 2018                [Page 29]


Internet-Draft                    JSEP                    September 2017


   This API changes the local media state; among other things, it sets
   up local resources for sending and encoding media.

   If setLocalDescription was previously called with an offer, and
   setRemoteDescription is called with an answer (provisional or final),
   and the media directions are compatible, and media is available to
   send, this will result in the starting of media transmission.

4.1.11.  currentLocalDescription

   The currentLocalDescription method returns the current negotiated
   local description - i.e., the local description from the last
   successful offer/answer exchange - in addition to any local
   candidates that have been generated by the ICE agent since the local
   description was set.

   A null object will be returned if an offer/answer exchange has not
   yet been completed.

4.1.12.  pendingLocalDescription

   The pendingLocalDescription method returns a copy of the local
   description currently in negotiation - i.e., a local offer set
   without any corresponding remote answer - in addition to any local
   candidates that have been generated by the ICE agent since the local
   description was set.

   A null object will be returned if the state of the PeerConnection is
   "stable" or "have-remote-offer".

4.1.13.  currentRemoteDescription

   The currentRemoteDescription method returns a copy of the current
   negotiated remote description - i.e., the remote description from the
   last successful offer/answer exchange - in addition to any remote
   candidates that have been supplied via processIceMessage since the
   remote description was set.

   A null object will be returned if an offer/answer exchange has not
   yet been completed.

4.1.14.  pendingRemoteDescription

   The pendingRemoteDescription method returns a copy of the remote
   description currently in negotiation - i.e., a remote offer set
   without any corresponding local answer - in addition to any remote
   candidates that have been supplied via processIceMessage since the
   remote description was set.



Uberti, et al.            Expires March 5, 2018                [Page 30]


Internet-Draft                    JSEP                    September 2017


   A null object will be returned if the state of the PeerConnection is
   "stable" or "have-local-offer".

4.1.15.  canTrickleIceCandidates

   The canTrickleIceCandidates property indicates whether the remote
   side supports receiving trickled candidates.  There are three
   potential values:

   null:  No SDP has been received from the other side, so it is not
      known if it can handle trickle.  This is the initial value before
      setRemoteDescription() is called.

   true:  SDP has been received from the other side indicating that it
      can support trickle.

   false:  SDP has been received from the other side indicating that it
      cannot support trickle.

   As described in Section 3.5.2, JSEP implementations always provide
   candidates to the application individually, consistent with what is
   needed for Trickle ICE.  However, applications can use the
   canTrickleIceCandidates property to determine whether their peer can
   actually do Trickle ICE, i.e., whether it is safe to send an initial
   offer or answer followed later by candidates as they are gathered.
   As "true" is the only value that definitively indicates remote
   Trickle ICE support, an application which compares
   canTrickleIceCandidates against "true" will by default attempt Half
   Trickle on initial offers and Full Trickle on subsequent interactions
   with a Trickle ICE-compatible agent.

4.1.16.  setConfiguration

   The setConfiguration method allows the global configuration of the
   PeerConnection, which was initially set by constructor parameters, to
   be changed during the session.  The effects of this method call
   depend on when it is invoked, and differ depending on which specific
   parameters are changed:

   o  Any changes to the STUN/TURN servers to use affect the next
      gathering phase.  If an ICE gathering phase has already started or
      completed, the 'needs-ice-restart' bit mentioned in Section 3.5.1
      will be set.  This will cause the next call to createOffer to
      generate new ICE credentials, for the purpose of forcing an ICE
      restart and kicking off a new gathering phase, in which the new
      servers will be used.  If the ICE candidate pool has a nonzero
      size, and a local description has not yet been applied, any




Uberti, et al.            Expires March 5, 2018                [Page 31]


Internet-Draft                    JSEP                    September 2017


      existing candidates will be discarded, and new candidates will be
      gathered from the new servers.

   o  Any change to the ICE candidate policy affects the next gathering
      phase.  If an ICE gathering phase has already started or
      completed, the 'needs-ice-restart' bit will be set.  Either way,
      changes to the policy have no effect on the candidate pool,
      because pooled candidates are not made available to the
      application until a gathering phase occurs, and so any necessary
      filtering can still be done on any pooled candidates.

   o  The ICE candidate pool size MUST NOT be changed after applying a
      local description.  If a local description has not yet been
      applied, any changes to the ICE candidate pool size take effect
      immediately; if increased, additional candidates are pre-gathered;
      if decreased, the now-superfluous candidates are discarded.

   o  The bundle and RTCP-multiplexing policies MUST NOT be changed
      after the construction of the PeerConnection.

   This call may result in a change to the state of the ICE Agent.

4.1.17.  addIceCandidate

   The addIceCandidate method provides an update to the ICE agent via an
   IceCandidate object Section 3.5.2.1.  If the IceCandidate's candidate
   field is filled in, the IceCandidate is treated as a new remote ICE
   candidate, which will be added to the current and/or pending remote
   description according to the rules defined for Trickle ICE.
   Otherwise, the IceCandidate is treated as an end-of-candidates
   indication, as defined in [I-D.ietf-ice-trickle].

   In either case, the m= section index, MID, and ufrag fields from the
   supplied IceCandidate are used to determine which m= section and ICE
   candidate generation the IceCandidate belongs to, as described in
   Section 3.5.2.1 above.  In the case of an end-of-candidates
   indication, the absence of both the m= section index and MID fields
   is interpreted to mean that the indication applies to all m= sections
   in the specified ICE candidate generation.  However, if both fields
   are absent for a new remote candidate, this MUST be treated as an
   invalid condition, as specified below.

   If any IceCandidate fields contain invalid values, or an error occurs
   during the processing of the IceCandidate object, the supplied
   IceCandidate MUST be ignored and an error MUST be returned.






Uberti, et al.            Expires March 5, 2018                [Page 32]


Internet-Draft                    JSEP                    September 2017


   Otherwise, the new remote candidate or end-of-candidates indication
   is supplied to the ICE agent.  In the case of a new remote candidate,
   connectivity checks will be sent to the new candidate.

4.2.  RtpTransceiver

4.2.1.  stop

   The stop method stops an RtpTransceiver.  This will cause future
   calls to createOffer to generate a zero port for the associated m=
   section.  See below for more details.

4.2.2.  stopped

   The stopped property indicates whether the transceiver has been
   stopped, either by a call to stopTransceiver or by applying an answer
   that rejects the associated m= section.  In either of these cases, it
   is set to "true", and otherwise will be set to "false".

   A stopped RtpTransceiver does not send any outgoing RTP or RTCP or
   process any incoming RTP or RTCP.  It cannot be restarted.

4.2.3.  setDirection

   The setDirection method sets the direction of a transceiver, which
   affects the direction property of the associated m= section on future
   calls to createOffer and createAnswer.  The permitted values for
   direction are "recvonly", "sendrecv", "sendonly", and "inactive",
   mirroring the identically-named directional attributes defined in
   [RFC4566], Section 6.

   When creating offers, the transceiver direction is directly reflected
   in the output, even for re-offers.  When creating answers, the
   transceiver direction is intersected with the offered direction, as
   explained in Section 5.3 below.

   Note that while setDirection sets the direction property of the
   transceiver immediately (Section 4.2.4), this property does not
   immediately affect whether the transceiver's RtpSender will send or
   its RtpReceiver will receive.  The direction in effect is represented
   by the currentDirection property, which is only updated when an
   answer is applied.

4.2.4.  direction

   The direction property indicates the last value passed into
   setDirection.  If setDirection has never been called, it is set to
   the direction the transceiver was initialized with.



Uberti, et al.            Expires March 5, 2018                [Page 33]


Internet-Draft                    JSEP                    September 2017


4.2.5.  currentDirection

   The currentDirection property indicates the last negotiated direction
   for the transceiver's associated m= section.  More specifically, it
   indicates the [RFC3264] directional attribute of the associated m=
   section in the last applied answer (including provisional answers),
   with "send" and "recv" directions reversed if it was a remote answer.
   For example, if the directional attribute for the associated m=
   section in a remote answer is "recvonly", currentDirection is set to
   "sendonly".

   If an answer that references this transceiver has not yet been
   applied, or if the transceiver is stopped, currentDirection is set to
   null.

4.2.6.  setCodecPreferences

   The setCodecPreferences method sets the codec preferences of a
   transceiver, which in turn affect the presence and order of codecs of
   the associated m= section on future calls to createOffer and
   createAnswer.  Note that setCodecPreferences does not directly affect
   which codec the implementation decides to send.  It only affects
   which codecs the implementation indicates that it prefers to receive,
   via the offer or answer.  Even when a codec is excluded by
   setCodecPreferences, it still may be used to send until the next
   offer/answer exchange discards it.

   The codec preferences of an RtpTransceiver can cause codecs to be
   excluded by subsequent calls to createOffer and createAnswer, in
   which case the corresponding media formats in the associated m=
   section will be excluded.  The codec preferences cannot add media
   formats that would otherwise not be present.

   The codec preferences of an RtpTransceiver can also determine the
   order of codecs in subsequent calls to createOffer and createAnswer,
   in which case the order of the media formats in the associated m=
   section will follow the specified preferences.

5.  SDP Interaction Procedures

   This section describes the specific procedures to be followed when
   creating and parsing SDP objects.

5.1.  Requirements Overview

   JSEP implementations must comply with the specifications listed below
   that govern the creation and processing of offers and answers.




Uberti, et al.            Expires March 5, 2018                [Page 34]


Internet-Draft                    JSEP                    September 2017


5.1.1.  Usage Requirements

   All session descriptions handled by JSEP implementations, both local
   and remote, MUST indicate support for the following specifications.
   If any of these are absent, this omission MUST be treated as an
   error.

   o  ICE, as specified in [RFC5245], MUST be used.  Note that the
      remote endpoint may use a Lite implementation; implementations
      MUST properly handle remote endpoints which do ICE-Lite.

   o  DTLS [RFC6347] or DTLS-SRTP [RFC5763], MUST be used, as
      appropriate for the media type, as specified in
      [I-D.ietf-rtcweb-security-arch]

   The SDES SRTP keying mechanism from [RFC4568] MUST NOT be used, as
   discussed in [I-D.ietf-rtcweb-security-arch].

5.1.2.  Profile Names and Interoperability

   For media m= sections, JSEP implementations MUST support the
   "UDP/TLS/RTP/SAVPF" profile specified in [RFC5764], and MUST indicate
   this profile for each media m= line they produce in an offer.  For
   data m= sections, implementations MUST support the "UDP/DTLS/SCTP"
   profile and MUST indicate this profile for each data m= line they
   produce in an offer.  Although these profiles are formally associated
   with UDP, ICE can select either UDP [RFC5245] or TCP [RFC6544]
   transport depending on network conditions, even when advertising a
   UDP profile.

   Unfortunately, in an attempt at compatibility, some endpoints
   generate other profile strings even when they mean to support one of
   these profiles.  For instance, an endpoint might generate "RTP/AVP"
   but supply "a=fingerprint" and "a=rtcp-fb" attributes, indicating its
   willingness to support "UDP/TLS/RTP/SAVPF" or "TCP/TLS/RTP/SAVPF".
   In order to simplify compatibility with such endpoints, JSEP
   implementations MUST follow the following rules when processing the
   media m= sections in a received offer:

   o  Any profile in the offer matching one of the following MUST be
      accepted:

      *  "RTP/AVP" (Defined in [RFC4566], Section 8.2.2)

      *  "RTP/AVPF" (Defined in [RFC4585], Section 9)

      *  "RTP/SAVP" (Defined in [RFC3711], Section 12)




Uberti, et al.            Expires March 5, 2018                [Page 35]


Internet-Draft                    JSEP                    September 2017


      *  "RTP/SAVPF" (Defined in [RFC5124], Section 6)

      *  "TCP/DTLS/RTP/SAVP" (Defined in [RFC7850], Section 3.4)

      *  "TCP/DTLS/RTP/SAVPF" (Defined in [RFC7850], Section 3.5)

      *  "UDP/TLS/RTP/SAVP" (Defined in [RFC5764], Section 9)

      *  "UDP/TLS/RTP/SAVPF" (Defined in [RFC5764], Section 9)

   o  The profile in any "m=" line in any generated answer MUST exactly
      match the profile provided in the offer.

   o  Because DTLS-SRTP is REQUIRED, the choice of SAVP or AVP has no
      effect; support for DTLS-SRTP is determined by the presence of one
      or more "a=fingerprint" attribute.  Note that lack of an
      "a=fingerprint" attribute will lead to negotiation failure.

   o  The use of AVPF or AVP simply controls the timing rules used for
      RTCP feedback.  If AVPF is provided, or an "a=rtcp-fb" attribute
      is present, assume AVPF timing, i.e., a default value of "trr-
      int=0".  Otherwise, assume that AVPF is being used in an AVP
      compatible mode and use a value of "trr-int=4000".

   o  For data m= sections, implementations MUST support receiving the
      "UDP/DTLS/SCTP", "TCP/DTLS/SCTP", or "DTLS/SCTP" (for backwards
      compatibility) profiles.

   Note that re-offers by JSEP implementations MUST use the correct
   profile strings even if the initial offer/answer exchange used an
   (incorrect) older profile string.  This simplifies JSEP behavior,
   with minimal downside, as any remote endpoint that fails to handle
   such a re-offer will also fail to handle a JSEP endpoint's initial
   offer.

5.2.  Constructing an Offer

   When createOffer is called, a new SDP description must be created
   that includes the functionality specified in
   [I-D.ietf-rtcweb-rtp-usage].  The exact details of this process are
   explained below.

5.2.1.  Initial Offers

   When createOffer is called for the first time, the result is known as
   the initial offer.





Uberti, et al.            Expires March 5, 2018                [Page 36]


Internet-Draft                    JSEP                    September 2017


   The first step in generating an initial offer is to generate session-
   level attributes, as specified in [RFC4566], Section 5.
   Specifically:

   o  The first SDP line MUST be "v=0", as specified in [RFC4566],
      Section 5.1

   o  The second SDP line MUST be an "o=" line, as specified in
      [RFC4566], Section 5.2.  The value of the <username> field SHOULD
      be "-".  The sess-id MUST be representable by a 64-bit signed
      integer, and the initial value MUST be less than (2**62)-1, as
      required by [RFC3264].  It is RECOMMENDED that the sess-id be
      constructed by generating a 64-bit quantity with the two highest
      bits being set to zero and the remaining 62 bits being
      cryptographically random.  The value of the <nettype> <addrtype>
      <unicast-address> tuple SHOULD be set to a non-meaningful address,
      such as IN IP4 0.0.0.0, to prevent leaking the local address in
      this field.  As mentioned in [RFC4566], the entire o= line needs
      to be unique, but selecting a random number for <sess-id> is
      sufficient to accomplish this.

   o  The third SDP line MUST be a "s=" line, as specified in [RFC4566],
      Section 5.3; to match the "o=" line, a single dash SHOULD be used
      as the session name, e.g. "s=-".  Note that this differs from the
      advice in [RFC4566] which proposes a single space, but as both
      "o=" and "s=" are meaningless in JSEP, having the same meaningless
      value seems clearer.

   o  Session Information ("i="), URI ("u="), Email Address ("e="),
      Phone Number ("p="), Repeat Times ("r="), and Time Zones ("z=")
      lines are not useful in this context and SHOULD NOT be included.

   o  Encryption Keys ("k=") lines do not provide sufficient security
      and MUST NOT be included.

   o  A "t=" line MUST be added, as specified in [RFC4566], Section 5.9;
      both <start-time> and <stop-time> SHOULD be set to zero, e.g. "t=0
      0".

   o  An "a=ice-options" line with the "trickle" option MUST be added,
      as specified in [I-D.ietf-ice-trickle], Section 4.

   o  If WebRTC identity is being used, an "a=identity" line as
      described in [I-D.ietf-rtcweb-security-arch], Section 5.

   The next step is to generate m= sections, as specified in [RFC4566],
   Section 5.14.  An m= section is generated for each RtpTransceiver
   that has been added to the PeerConnection, excluding any stopped



Uberti, et al.            Expires March 5, 2018                [Page 37]


Internet-Draft                    JSEP                    September 2017


   RtpTransceivers; this is done in the order the RtpTransceivers were
   added to the PeerConnection.  If there are no such RtpTransceivers,
   no m= sections are generated; more can be added later, as discussed
   in [RFC3264], Section 5.

   For each m= section generated for an RtpTransceiver, establish a
   mapping between the transceiver and the index of the generated m=
   section.

   Each m= section, provided it is not marked as bundle-only, MUST
   generate a unique set of ICE credentials and gather its own unique
   set of ICE candidates.  Bundle-only m= sections MUST NOT contain any
   ICE credentials and MUST NOT gather any candidates.

   For DTLS, all m= sections MUST use all the certificate(s) that have
   been specified for the PeerConnection; as a result, they MUST all
   have the same [RFC8122] fingerprint value(s), or these value(s) MUST
   be session-level attributes.

   Each m= section should be generated as specified in [RFC4566],
   Section 5.14.  For the m= line itself, the following rules MUST be
   followed:

   o  If the m= section is marked as bundle-only, then the port value
      MUST be set to 0.  Otherwise, the port value is set to the port of
      the default ICE candidate for this m= section, but given that no
      candidates are available yet, the "dummy" port value of 9
      (Discard) MUST be used, as indicated in [I-D.ietf-ice-trickle],
      Section 5.1.

   o  To properly indicate use of DTLS, the <proto> field MUST be set to
      "UDP/TLS/RTP/SAVPF", as specified in [RFC5764], Section 8.

   o  If codec preferences have been set for the associated transceiver,
      media formats MUST be generated in the corresponding order, and
      MUST exclude any codecs not present in the codec preferences.

   o  Unless excluded by the above restrictions, the media formats MUST
      include the mandatory audio/video codecs as specified in
      [RFC7874], Section 3, and [RFC7742], Section 5.

   The m= line MUST be followed immediately by a "c=" line, as specified
   in [RFC4566], Section 5.7.  Again, as no candidates are available
   yet, the "c=" line must contain the "dummy" value "IN IP4 0.0.0.0",
   as defined in [I-D.ietf-ice-trickle], Section 5.1.

   [I-D.ietf-mmusic-sdp-mux-attributes] groups SDP attributes into
   different categories.  To avoid unnecessary duplication when



Uberti, et al.            Expires March 5, 2018                [Page 38]


Internet-Draft                    JSEP                    September 2017


   bundling, attributes of category IDENTICAL or TRANSPORT MUST NOT be
   repeated in bundled m= sections, repeating the guidance from
   [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 8.1.  This includes
   m= sections for which bundling has been negotiated and is still
   desired, as well as m= sections marked as bundle-only.

   The following attributes, which are of a category other than
   IDENTICAL or TRANSPORT, MUST be included in each m= section:

   o  An "a=mid" line, as specified in [RFC5888], Section 4.  All MID
      values MUST be generated in a fashion that does not leak user
      information, e.g., randomly or using a per-PeerConnection counter,
      and SHOULD be 3 bytes or less, to allow them to efficiently fit
      into the RTP header extension defined in
      [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 14.  Note that
      this does not set the RtpTransceiver mid property, as that only
      occurs when the description is applied.  The generated MID value
      can be considered a "proposed" MID at this point.

   o  A direction attribute which is the same as that of the associated
      transceiver.

   o  For each media format on the m= line, "a=rtpmap" and "a=fmtp"
      lines, as specified in [RFC4566], Section 6, and [RFC3264],
      Section 5.1.

   o  For each primary codec where RTP retransmission should be used, a
      corresponding "a=rtpmap" line indicating "rtx" with the clock rate
      of the primary codec and an "a=fmtp" line that references the
      payload type of the primary codec, as specified in [RFC4588],
      Section 8.1.

   o  For each supported FEC mechanism, "a=rtpmap" and "a=fmtp" lines,
      as specified in [RFC4566], Section 6.  The FEC mechanisms that
      MUST be supported are specified in [I-D.ietf-rtcweb-fec],
      Section 6, and specific usage for each media type is outlined in
      Sections 4 and 5.

   o  If this m= section is for media with configurable durations of
      media per packet, e.g., audio, an "a=maxptime" line, indicating
      the maximum amount of media, specified in milliseconds, that can
      be encapsulated in each packet, as specified in [RFC4566],
      Section 6.  This value is set to the smallest of the maximum
      duration values across all the codecs included in the m= section.

   o  If this m= section is for video media, and there are known
      limitations on the size of images which can be decoded, an
      "a=imageattr" line, as specified in Section 3.6.



Uberti, et al.            Expires March 5, 2018                [Page 39]


Internet-Draft                    JSEP                    September 2017


   o  For each supported RTP header extension, an "a=extmap" line, as
      specified in [RFC5285], Section 5.  The list of header extensions
      that SHOULD/MUST be supported is specified in
      [I-D.ietf-rtcweb-rtp-usage], Section 5.2.  Any header extensions
      that require encryption MUST be specified as indicated in
      [RFC6904], Section 4.

   o  For each supported RTCP feedback mechanism, an "a=rtcp-fb" line,
      as specified in [RFC4585], Section 4.2.  The list of RTCP feedback
      mechanisms that SHOULD/MUST be supported is specified in
      [I-D.ietf-rtcweb-rtp-usage], Section 5.1.

   o  If the RtpTransceiver has a sendrecv or sendonly direction:

      *  For each MediaStream that was associated with the transceiver
         when it was created via addTrack or addTransceiver, an "a=msid"
         line, as specified in [I-D.ietf-mmusic-msid], Section 2.  If a
         MediaStreamTrack is attached to the transceiver's RtpSender,
         the "a=msid" lines MUST use that track's ID.  If no
         MediaStreamTrack is attached, a valid ID MUST be generated, in
         the same way that the implementation generates IDs for local
         tracks.

      *  If no MediaStream is associated with the transceiver, a single
         "a=msid" line with the special value "-" in place of the
         MediaStream ID, as specified in [I-D.ietf-mmusic-msid],
         Section 3.  The track ID MUST be selected as described above.

   o  If the RtpTransceiver has a sendrecv or sendonly direction, and
      the application has specified RID values or has specified more
      than one encoding in the RtpSenders's parameters, an "a=rid" line
      for each encoding specified.  The "a=rid" line is specified in
      [I-D.ietf-mmusic-rid], and its direction MUST be "send".  If the
      application has chosen a RID value, it MUST be used as the rid-
      identifier; otherwise a RID value MUST be generated by the
      implementation.  RID values MUST be generated in a fashion that
      does not leak user information, e.g., randomly or using a per-
      PeerConnection counter, and SHOULD be 3 bytes or less, to allow
      them to efficiently fit into the RTP header extension defined in
      [I-D.ietf-avtext-rid], Section 3.  If no encodings have been
      specified, or only one encoding is specified but without a RID
      value, then no "a=rid" lines are generated.

   o  If the RtpTransceiver has a sendrecv or sendonly direction and
      more than one "a=rid" line has been generated, an "a=simulcast"
      line, with direction "send", as defined in
      [I-D.ietf-mmusic-sdp-simulcast], Section 6.2.  The list of RIDs




Uberti, et al.            Expires March 5, 2018                [Page 40]


Internet-Draft                    JSEP                    September 2017


      MUST include all of the RID identifiers used in the "a=rid" lines
      for this m= section.

   o  If the bundle policy for this PeerConnection is set to "max-
      bundle", and this is not the first m= section, or the bundle
      policy is set to "balanced", and this is not the first m= section
      for this media type, an "a=bundle-only" line.

   The following attributes, which are of category IDENTICAL or
   TRANSPORT, MUST appear only in "m=" sections which either have a
   unique address or which are associated with the bundle-tag.  (In
   initial offers, this means those "m=" sections which do not contain
   an "a=bundle-only" attribute.)

   o  "a=ice-ufrag" and "a=ice-pwd" lines, as specified in [RFC5245],
      Section 15.4.

   o  For each desired digest algorithm, one or more "a=fingerprint"
      lines for each of the endpoint's certificates, as specified in
      [RFC8122], Section 5.

   o  An "a=setup" line, as specified in [RFC4145], Section 4, and
      clarified for use in DTLS-SRTP scenarios in [RFC5763], Section 5.
      The role value in the offer MUST be "actpass".

   o  An "a=tls-id" line, as specified in [I-D.ietf-mmusic-dtls-sdp],
      Section 5.2.

   o  An "a=rtcp" line, as specified in [RFC3605], Section 2.1,
      containing the dummy value "9 IN IP4 0.0.0.0", because no
      candidates have yet been gathered.

   o  An "a=rtcp-mux" line, as specified in [RFC5761], Section 5.1.3.

   o  If the RTP/RTCP multiplexing policy is "require", an "a=rtcp-mux-
      only" line, as specified in [I-D.ietf-mmusic-mux-exclusive],
      Section 4.

   o  An "a=rtcp-rsize" line, as specified in [RFC5506], Section 5.

   Lastly, if a data channel has been created, a m= section MUST be
   generated for data.  The <media> field MUST be set to "application"
   and the <proto> field MUST be set to "UDP/DTLS/SCTP"
   [I-D.ietf-mmusic-sctp-sdp].  The "fmt" value MUST be set to "webrtc-
   datachannel" as specified in [I-D.ietf-mmusic-sctp-sdp], Section 4.1.

   Within the data m= section, an "a=mid" line MUST be generated and
   included as described above, along with an "a=sctp-port" line



Uberti, et al.            Expires March 5, 2018                [Page 41]


Internet-Draft                    JSEP                    September 2017


   referencing the SCTP port number, as defined in
   [I-D.ietf-mmusic-sctp-sdp], Section 5.1, and, if appropriate, an
   "a=max-message-size" line, as defined in [I-D.ietf-mmusic-sctp-sdp],
   Section 6.1.

   As discussed above, the following attributes of category IDENTICAL or
   TRANSPORT are included only if the data m= section either has a
   unique address or is associated with the bundle-tag (e.g., if it is
   the only m= section):

   o  "a=ice-ufrag"

   o  "a=ice-pwd"

   o  "a=fingerprint"

   o  "a=setup"

   o  "a=tls-id"

   Once all m= sections have been generated, a session-level "a=group"
   attribute MUST be added as specified in [RFC5888].  This attribute
   MUST have semantics "BUNDLE", and MUST include the mid identifiers of
   each m= section.  The effect of this is that the JSEP implementation
   offers all m= sections as one bundle group.  However, whether the m=
   sections are bundle-only or not depends on the bundle policy.

   The next step is to generate session-level lip sync groups as defined
   in [RFC5888], Section 7.  For each MediaStream referenced by more
   than one RtpTransceiver (by passing those MediaStreams as arguments
   to the addTrack and addTransceiver methods), a group of type "LS"
   MUST be added that contains the mid values for each RtpTransceiver.

   Attributes which SDP permits to either be at the session level or the
   media level SHOULD generally be at the media level even if they are
   identical.  This assists development and debugging by making it
   easier to understand individual media sections, especially if one of
   a set of initially identical attributes is subsequently changed.
   However, implementations MAY choose to aggregate attributes at the
   session level and JSEP implementations MUST be prepared to receive
   attributes in either location.

   Attributes other than the ones specified above MAY be included,
   except for the following attributes which are specifically
   incompatible with the requirements of [I-D.ietf-rtcweb-rtp-usage],
   and MUST NOT be included:

   o  "a=crypto"



Uberti, et al.            Expires March 5, 2018                [Page 42]


Internet-Draft                    JSEP                    September 2017


   o  "a=key-mgmt"

   o  "a=ice-lite"

   Note that when bundle is used, any additional attributes that are
   added MUST follow the advice in [I-D.ietf-mmusic-sdp-mux-attributes]
   on how those attributes interact with bundle.

   Note that these requirements are in some cases stricter than those of
   SDP.  Implementations MUST be prepared to accept compliant SDP even
   if it would not conform to the requirements for generating SDP in
   this specification.

5.2.2.  Subsequent Offers

   When createOffer is called a second (or later) time, or is called
   after a local description has already been installed, the processing
   is somewhat different than for an initial offer.

   If the previous offer was not applied using setLocalDescription,
   meaning the PeerConnection is still in the "stable" state, the steps
   for generating an initial offer should be followed, subject to the
   following restriction:

   o  The fields of the "o=" line MUST stay the same except for the
      <session-version> field, which MUST increment by one on each call
      to createOffer if the offer might differ from the output of the
      previous call to createOffer; implementations MAY opt to increment
      <session-version> on every call.  The value of the generated
      <session-version> is independent of the <session-version> of the
      current local description; in particular, in the case where the
      current version is N, an offer is created and applied with version
      N+1, and then that offer is rolled back so that the current
      version is again N, the next generated offer will still have
      version N+2.

   Note that if the application creates an offer by reading
   currentLocalDescription instead of calling createOffer, the returned
   SDP may be different than when setLocalDescription was originally
   called, due to the addition of gathered ICE candidates, but the
   <session-version> will not have changed.  There are no known
   scenarios in which this causes problems, but if this is a concern,
   the solution is simply to use createOffer to ensure a unique
   <session-version>.

   If the previous offer was applied using setLocalDescription, but a
   corresponding answer from the remote side has not yet been applied,
   meaning the PeerConnection is still in the "have-local-offer" state,



Uberti, et al.            Expires March 5, 2018                [Page 43]


Internet-Draft                    JSEP                    September 2017


   an offer is generated by following the steps in the "stable" state
   above, along with these exceptions:

   o  The "s=" and "t=" lines MUST stay the same.

   o  If any RtpTransceiver has been added, and there exists an m=
      section with a zero port in the current local description or the
      current remote description, that m= section MUST be recycled by
      generating an m= section for the added RtpTransceiver as if the m=
      section were being added to the session description (including a
      new MID value), and placing it at the same index as the m= section
      with a zero port.

   o  If an RtpTransceiver is stopped and is not associated with an m=
      section, an m= section MUST NOT be generated for it.  This
      prevents adding back RtpTransceivers whose m= sections were
      recycled and used for a new RtpTransceiver in a previous offer/
      answer exchange, as described above.

   o  If an RtpTransceiver has been stopped and is associated with an m=
      section, and the m= section is not being recycled as described
      above, an m= section MUST be generated for it with the port set to
      zero and all "a=msid" lines removed.

   o  For RtpTransceivers that are not stopped, the "a=msid" line(s)
      MUST stay the same if they are present in the current description,
      regardless of changes to the transceiver's direction or track.  If
      no "a=msid" line is present in the current description, "a=msid"
      line(s) MUST be generated according to the same rules as for an
      initial offer.

   o  Each "m=" and c=" line MUST be filled in with the port, protocol,
      and address of the default candidate for the m= section, as
      described in [RFC5245], Section 4.3.  If ICE checking has already
      completed for one or more candidate pairs and a candidate pair is
      in active use, then that pair MUST be used, even if ICE has not
      yet completed.  Note that this differs from the guidance in
      [RFC5245], Section 9.1.2.2, which only refers to offers created
      when ICE has completed.  In each case, if no RTP candidates have
      yet been gathered, dummy values MUST be used, as described above.

   o  Each "a=mid" line MUST stay the same.

   o  Each "a=ice-ufrag" and "a=ice-pwd" line MUST stay the same, unless
      the ICE configuration has changed (either changes to the supported
      STUN/TURN servers, or the ICE candidate policy), or the
      "IceRestart" option ( Section 5.2.3.1 was specified.  If the m=




Uberti, et al.            Expires March 5, 2018                [Page 44]


Internet-Draft                    JSEP                    September 2017


      section is bundled into another m= section, it still MUST NOT
      contain any ICE credentials.

   o  If the m= section is not bundled into another m= section, its
      "a=rtcp" attribute line MUST be filled in with the port and
      address of the default RTCP candidate, as indicated in [RFC5761],
      Section 5.1.3.  If no RTCP candidates have yet been gathered,
      dummy values MUST be used, as described in the initial offer
      section above.

   o  If the m= section is not bundled into another m= section, for each
      candidate that has been gathered during the most recent gathering
      phase (see Section 3.5.1), an "a=candidate" line MUST be added, as
      defined in [RFC5245], Section 4.3., paragraph 3.  If candidate
      gathering for the section has completed, an "a=end-of-candidates"
      attribute MUST be added, as described in [I-D.ietf-ice-trickle],
      Section 9.3.  If the m= section is bundled into another m=
      section, both "a=candidate" and "a=end-of-candidates" MUST be
      omitted.

   o  For RtpTransceivers that are still present, the "a=rid" lines MUST
      stay the same.

   o  For RtpTransceivers that are still present, any "a=simulcast" line
      MUST stay the same.

   If the previous offer was applied using setLocalDescription, and a
   corresponding answer from the remote side has been applied using
   setRemoteDescription, meaning the PeerConnection is in the "have-
   remote-pranswer" or "stable" states, an offer is generated based on
   the negotiated session descriptions by following the steps mentioned
   for the "have-local-offer" state above.

   In addition, for each existing, non-recycled, non-rejected m= section
   in the new offer, the following adjustments are made based on the
   contents of the corresponding m= section in the current local or
   remote description, as appropriate:

   o  The m= line and corresponding "a=rtpmap" and "a=fmtp" lines MUST
      only include media formats which have not been excluded by the
      codec preferences of the associated transceiver, and MUST include
      all currently available formats.  Media formats that were
      previously offered but are no longer available (e.g., a shared
      hardware codec) MAY be excluded.

   o  Unless codec preferences have been set for the associated
      transceiver, the media formats on the m= line MUST be generated in
      the same order as in the most recent answer.  Any media formats



Uberti, et al.            Expires March 5, 2018                [Page 45]


Internet-Draft                    JSEP                    September 2017


      that were not present in the most recent answer MUST be added
      after all existing formats.

   o  The RTP header extensions MUST only include those that are present
      in the most recent answer.

   o  The RTCP feedback mechanisms MUST only include those that are
      present in the most recent answer, except for the case of format-
      specific mechanisms that are referencing a newly-added media
      format.

   o  The "a=rtcp" line MUST NOT be added if the most recent answer
      included an "a=rtcp-mux" line.

   o  The "a=rtcp-mux" line MUST be the same as that in the most recent
      answer.

   o  The "a=rtcp-mux-only" line MUST NOT be added.

   o  The "a=rtcp-rsize" line MUST NOT be added unless present in the
      most recent answer.

   o  An "a=bundle-only" line MUST NOT be added, as indicated in
      [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 6.  Instead,
      JSEP implementations MUST simply omit parameters in the IDENTICAL
      and TRANSPORT categories for bundled m= sections, as described in
      [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 8.1.

   o  Note that if media m= sections are bundled into a data m= section,
      then certain TRANSPORT and IDENTICAL attributes may appear in the
      data m= section even if they would otherwise only be appropriate
      for a media m= section (e.g., "a=rtcp-mux").  This cannot happen
      in initial offers because in the initial offer JSEP
      implementations always list media m= sections (if any) before the
      data m= section (if any), and at least one of those media m=
      sections will not have the "a=bundle-only" attribute.  Therefore,
      in initial offers, any "a=bundle-only" m= sections will be bundled
      into a preceding non-bundle-only media m= section.

   The "a=group:BUNDLE" attribute MUST include the MID identifiers
   specified in the bundle group in the most recent answer, minus any m=
   sections that have been marked as rejected, plus any newly added or
   re-enabled m= sections.  In other words, the bundle attribute must
   contain all m= sections that were previously bundled, as long as they
   are still alive, as well as any new m= sections.

   "a=group:LS" attributes are generated in the same way as for initial
   offers, with the additional stipulation that any lip sync groups that



Uberti, et al.            Expires March 5, 2018                [Page 46]


Internet-Draft                    JSEP                    September 2017


   were present in the most recent answer MUST continue to exist and
   MUST contain any previously existing MID identifiers, as long as the
   identified m= sections still exist and are not rejected, and the
   group still contains at least two MID identifiers.  This ensures that
   any synchronized "recvonly" m= sections continue to be synchronized
   in the new offer.

5.2.3.  Options Handling

   The createOffer method takes as a parameter an RTCOfferOptions
   object.  Special processing is performed when generating a SDP
   description if the following options are present.

5.2.3.1.  IceRestart

   If the "IceRestart" option is specified, with a value of "true", the
   offer MUST indicate an ICE restart by generating new ICE ufrag and
   pwd attributes, as specified in [RFC5245], Section 9.1.1.1.  If this
   option is specified on an initial offer, it has no effect (since a
   new ICE ufrag and pwd are already generated).  Similarly, if the ICE
   configuration has changed, this option has no effect, since new ufrag
   and pwd attributes will be generated automatically.  This option is
   primarily useful for reestablishing connectivity in cases where
   failures are detected by the application.

5.2.3.2.  VoiceActivityDetection

   Silence suppression, also known as discontinuous transmission
   ("DTX"), can reduce the bandwidth used for audio by switching to a
   special encoding when voice activity is not detected, at the cost of
   some fidelity.

   If the "VoiceActivityDetection" option is specified, with a value of
   "true", the offer MUST indicate support for silence suppression in
   the audio it receives by including comfort noise ("CN") codecs for
   each offered audio codec, as specified in [RFC3389], Section 5.1,
   except for codecs that have their own internal silence suppression
   support.  For codecs that have their own internal silence suppression
   support, the appropriate fmtp parameters for that codec MUST be
   specified to indicate that silence suppression for received audio is
   desired.  For example, when using the Opus codec [RFC6716], the
   "usedtx=1" parameter, specified in [RFC7587], would be used in the
   offer.

   If the "VoiceActivityDetection" option is specified, with a value of
   "false", the JSEP implementation MUST NOT emit "CN" codecs.  For
   codecs that have their own internal silence suppression support, the
   appropriate fmtp parameters for that codec MUST be specified to



Uberti, et al.            Expires March 5, 2018                [Page 47]


Internet-Draft                    JSEP                    September 2017


   indicate that silence suppression for received audio is not desired.
   For example, when using the Opus codec, the "usedtx=0" parameter
   would be specified in the offer.  In addition, the implementation
   MUST NOT use silence suppression for media it generates, regardless
   of whether the "CN" codecs or related fmtp parameters appear in the
   peer's description.  The impact of these rules is that silence
   suppression in JSEP depends on mutual agreement of both sides, which
   ensures consistent handling regardless of which codec is used.

   The "VoiceActivityDetection" option does not have any impact on the
   setting of the "vad" value in the signaling of the client to mixer
   audio level header extension described in [RFC6464], Section 4.

5.3.  Generating an Answer

   When createAnswer is called, a new SDP description must be created
   that is compatible with the supplied remote description as well as
   the requirements specified in [I-D.ietf-rtcweb-rtp-usage].  The exact
   details of this process are explained below.

5.3.1.  Initial Answers

   When createAnswer is called for the first time after a remote
   description has been provided, the result is known as the initial
   answer.  If no remote description has been installed, an answer
   cannot be generated, and an error MUST be returned.

   Note that the remote description SDP may not have been created by a
   JSEP endpoint and may not conform to all the requirements listed in
   Section 5.2.  For many cases, this is not a problem.  However, if any
   mandatory SDP attributes are missing, or functionality listed as
   mandatory-to-use above is not present, this MUST be treated as an
   error, and MUST cause the affected m= sections to be marked as
   rejected.

   The first step in generating an initial answer is to generate
   session-level attributes.  The process here is identical to that
   indicated in the initial offers section above, except that the
   "a=ice-options" line, with the "trickle" option as specified in
   [I-D.ietf-ice-trickle], Section 4, is only included if such an option
   was present in the offer.

   The next step is to generate session-level lip sync groups, as
   defined in [RFC5888], Section 7.  For each group of type "LS" present
   in the offer, select the local RtpTransceivers that are referenced by
   the MID values in the specified group, and determine which of them
   either reference a common local MediaStream (specified in the calls
   to addTrack/addTransceiver used to create them), or have no



Uberti, et al.            Expires March 5, 2018                [Page 48]


Internet-Draft                    JSEP                    September 2017


   MediaStream to reference because they were not created by addTrack/
   addTransceiver.  If at least two such RtpTransceivers exist, a group
   of type "LS" with the mid values of these RtpTransceivers MUST be
   added.  Otherwise the offered "LS" group MUST be ignored and no
   corresponding group generated in the answer.

   As a simple example, consider the following offer of a single audio
   and single video track contained in the same MediaStream.  SDP lines
   not relevant to this example have been removed for clarity.  As
   explained in Section 5.2, a group of type "LS" has been added that
   references each track's RtpTransceiver.


             a=group:LS a1 v1
             m=audio 10000 UDP/TLS/RTP/SAVPF 0
             a=mid:a1
             a=msid:ms1 mst1a
             m=video 10001 UDP/TLS/RTP/SAVPF 96
             a=mid:v1
             a=msid:ms1 mst1v


   If the answerer uses a single MediaStream when it adds its tracks,
   both of its transceivers will reference this stream, and so the
   subsequent answer will contain a "LS" group identical to that in the
   offer, as shown below:


             a=group:LS a1 v1
             m=audio 20000 UDP/TLS/RTP/SAVPF 0
             a=mid:a1
             a=msid:ms2 mst2a
             m=video 20001 UDP/TLS/RTP/SAVPF 96
             a=mid:v1
             a=msid:ms2 mst2v


   However, if the answerer groups its tracks into separate
   MediaStreams, its transceivers will reference different streams, and
   so the subsequent answer will not contain a "LS" group.











Uberti, et al.            Expires March 5, 2018                [Page 49]


Internet-Draft                    JSEP                    September 2017


             m=audio 20000 UDP/TLS/RTP/SAVPF 0
             a=mid:a1
             a=msid:ms2a mst2a
             m=video 20001 UDP/TLS/RTP/SAVPF 96
             a=mid:v1
             a=msid:ms2b mst2v


   Finally, if the answerer does not add any tracks, its transceivers
   will not reference any MediaStreams, causing the preferences of the
   offerer to be maintained, and so the subsequent answer will contain
   an identical "LS" group.


             a=group:LS a1 v1
             m=audio 20000 UDP/TLS/RTP/SAVPF 0
             a=mid:a1
             a=recvonly
             m=video 20001 UDP/TLS/RTP/SAVPF 96
             a=mid:v1
             a=recvonly


   The Section 7.2 example later in this document shows a more involved
   case of "LS" group generation.

   The next step is to generate m= sections for each m= section that is
   present in the remote offer, as specified in [RFC3264], Section 6.
   For the purposes of this discussion, any session-level attributes in
   the offer that are also valid as media-level attributes are
   considered to be present in each m= section.  Each offered m= section
   will have an associated RtpTransceiver, as described in Section 5.10.
   If there are more RtpTransceivers than there are m= sections, the
   unmatched RtpTransceivers will need to be associated in a subsequent
   offer.

   For each offered m= section, if any of the following conditions are
   true, the corresponding m= section in the answer MUST be marked as
   rejected by setting the port in the m= line to zero, as indicated in
   [RFC3264], Section 6, and further processing for this m= section can
   be skipped:

   o  The associated RtpTransceiver has been stopped.

   o  None of the offered media formats are supported and, if
      applicable, allowed by codec preferences.





Uberti, et al.            Expires March 5, 2018                [Page 50]


Internet-Draft                    JSEP                    September 2017


   o  The bundle policy is "max-bundle", and this is not the first m=
      section or in the same bundle group as the first m= section.

   o  The bundle policy is "balanced", and this is not the first m=
      section for this media type or in the same bundle group as the
      first m= section for this media type.

   Otherwise, each m= section in the answer should then be generated as
   specified in [RFC3264], Section 6.1.  For the m= line itself, the
   following rules must be followed:

   o  The port value would normally be set to the port of the default
      ICE candidate for this m= section, but given that no candidates
      are available yet, the "dummy" port value of 9 (Discard) MUST be
      used, as indicated in [I-D.ietf-ice-trickle], Section 5.1.

   o  The <proto> field MUST be set to exactly match the <proto> field
      for the corresponding m= line in the offer.

   o  If codec preferences have been set for the associated transceiver,
      media formats MUST be generated in the corresponding order,
      regardless of what was offered, and MUST exclude any codecs not
      present in the codec preferences.

   o  Otherwise, the media formats on the m= line MUST be generated in
      the same order as those offered in the current remote description,
      excluding any currently unsupported formats.  Any currently
      available media formats that are not present in the current remote
      description MUST be added after all existing formats.

   o  In either case, the media formats in the answer MUST include at
      least one format that is present in the offer, but MAY include
      formats that are locally supported but not present in the offer,
      as mentioned in [RFC3264], Section 6.1.  If no common format
      exists, the m= section is rejected as described above.

   The m= line MUST be followed immediately by a "c=" line, as specified
   in [RFC4566], Section 5.7.  Again, as no candidates are available
   yet, the "c=" line must contain the "dummy" value "IN IP4 0.0.0.0",
   as defined in [I-D.ietf-ice-trickle], Section 5.1.

   If the offer supports bundle, all m= sections to be bundled must use
   the same ICE credentials and candidates; all m= sections not being
   bundled must use unique ICE credentials and candidates.  Each m=
   section MUST contain the following attributes (which are of attribute
   types other than IDENTICAL and TRANSPORT):





Uberti, et al.            Expires March 5, 2018                [Page 51]


Internet-Draft                    JSEP                    September 2017


   o  If and only if present in the offer, an "a=mid" line, as specified
      in [RFC5888], Section 9.1.  The "mid" value MUST match that
      specified in the offer.

   o  A direction attribute, determined by applying the rules regarding
      the offered direction specified in [RFC3264], Section 6.1, and
      then intersecting with the direction of the associated
      RtpTransceiver.  For example, in the case where an m= section is
      offered as "sendonly", and the local transceiver is set to
      "sendrecv", the result in the answer is a "recvonly" direction.

   o  For each media format on the m= line, "a=rtpmap" and "a=fmtp"
      lines, as specified in [RFC4566], Section 6, and [RFC3264],
      Section 6.1.

   o  If "rtx" is present in the offer, for each primary codec where RTP
      retransmission should be used, a corresponding "a=rtpmap" line
      indicating "rtx" with the clock rate of the primary codec and an
      "a=fmtp" line that references the payload type of the primary
      codec, as specified in [RFC4588], Section 8.1.

   o  For each supported FEC mechanism, "a=rtpmap" and "a=fmtp" lines,
      as specified in [RFC4566], Section 6.  The FEC mechanisms that
      MUST be supported are specified in [I-D.ietf-rtcweb-fec],
      Section 6, and specific usage for each media type is outlined in
      Sections 4 and 5.

   o  If this m= section is for media with configurable durations of
      media per packet, e.g., audio, an "a=maxptime" line, as described
      in Section 5.2.

   o  If this m= section is for video media, and there are known
      limitations on the size of images which can be decoded, an
      "a=imageattr" line, as specified in Section 3.6.

   o  For each supported RTP header extension that is present in the
      offer, an "a=extmap" line, as specified in [RFC5285], Section 5.
      The list of header extensions that SHOULD/MUST be supported is
      specified in [I-D.ietf-rtcweb-rtp-usage], Section 5.2.  Any header
      extensions that require encryption MUST be specified as indicated
      in [RFC6904], Section 4.

   o  For each supported RTCP feedback mechanism that is present in the
      offer, an "a=rtcp-fb" line, as specified in [RFC4585],
      Section 4.2.  The list of RTCP feedback mechanisms that SHOULD/
      MUST be supported is specified in [I-D.ietf-rtcweb-rtp-usage],
      Section 5.1.




Uberti, et al.            Expires March 5, 2018                [Page 52]


Internet-Draft                    JSEP                    September 2017


   o  If the RtpTransceiver has a sendrecv or sendonly direction:

      *  For each MediaStream that was associated with the transceiver
         when it was created via addTrack or addTransceiver, an "a=msid"
         line, as specified in [I-D.ietf-mmusic-msid], Section 2.  If a
         MediaStreamTrack is attached to the transceiver's RtpSender,
         the "a=msid" lines MUST use that track's ID.  If no
         MediaStreamTrack is attached, a valid ID MUST be generated, in
         the same way that the implementation generates IDs for local
         tracks.

      *  If no MediaStream is associated with the transceiver, a single
         "a=msid" line with the special value "-" in place of the
         MediaStream ID, as specified in [I-D.ietf-mmusic-msid],
         Section 3.  The track ID MUST be selected as described above.

   Each m= section which is not bundled into another m= section, MUST
   contain the following attributes (which are of category IDENTICAL or
   TRANSPORT):

   o  "a=ice-ufrag" and "a=ice-pwd" lines, as specified in [RFC5245],
      Section 15.4.

   o  For each desired digest algorithm, one or more "a=fingerprint"
      lines for each of the endpoint's certificates, as specified in
      [RFC8122], Section 5.

   o  An "a=setup" line, as specified in [RFC4145], Section 4, and
      clarified for use in DTLS-SRTP scenarios in [RFC5763], Section 5.
      The role value in the answer MUST be "active" or "passive".  When
      the offer contains the "actpass" value, as will always be the case
      with JSEP endpoints, the answerer SHOULD use the "active" role.
      Offers from non-JSEP endpoints MAY send other values for
      "a=setup", in which case the answer MUST use a value consistent
      with the value in the offer.

   o  An "a=tls-id" line, as specified in [I-D.ietf-mmusic-dtls-sdp],
      Section 5.3.

   o  If present in the offer, an "a=rtcp-mux" line, as specified in
      [RFC5761], Section 5.1.3.  Otherwise, an "a=rtcp" line, as
      specified in [RFC3605], Section 2.1, containing the dummy value "9
      IN IP4 0.0.0.0" (because no candidates have yet been gathered).

   o  If present in the offer, an "a=rtcp-rsize" line, as specified in
      [RFC5506], Section 5.





Uberti, et al.            Expires March 5, 2018                [Page 53]


Internet-Draft                    JSEP                    September 2017


   If a data channel m= section has been offered, a m= section MUST also
   be generated for data.  The <media> field MUST be set to
   "application" and the <proto> and <fmt> fields MUST be set to exactly
   match the fields in the offer.

   Within the data m= section, an "a=mid" line MUST be generated and
   included as described above, along with an "a=sctp-port" line
   referencing the SCTP port number, as defined in
   [I-D.ietf-mmusic-sctp-sdp], Section 5.1, and, if appropriate, an
   "a=max-message-size" line, as defined in [I-D.ietf-mmusic-sctp-sdp],
   Section 6.1.

   As discussed above, the following attributes of category IDENTICAL or
   TRANSPORT are included only if the data m= section is not bundled
   into another m= section:

   o  "a=ice-ufrag"

   o  "a=ice-pwd"

   o  "a=fingerprint"

   o  "a=setup"

   o  "a=tls-id"

   Note that if media m= sections are bundled into a data m= section,
   then certain TRANSPORT and IDENTICAL attributes may also appear in
   the data m= section even if they would otherwise only be appropriate
   for a media m= section (e.g., "a=rtcp-mux").

   If "a=group" attributes with semantics of "BUNDLE" are offered,
   corresponding session-level "a=group" attributes MUST be added as
   specified in [RFC5888].  These attributes MUST have semantics
   "BUNDLE", and MUST include the all mid identifiers from the offered
   bundle groups that have not been rejected.  Note that regardless of
   the presence of "a=bundle-only" in the offer, no m= sections in the
   answer should have an "a=bundle-only" line.

   Attributes that are common between all m= sections MAY be moved to
   session-level, if explicitly defined to be valid at session-level.

   The attributes prohibited in the creation of offers are also
   prohibited in the creation of answers.







Uberti, et al.            Expires March 5, 2018                [Page 54]


Internet-Draft                    JSEP                    September 2017


5.3.2.  Subsequent Answers

   When createAnswer is called a second (or later) time, or is called
   after a local description has already been installed, the processing
   is somewhat different than for an initial answer.

   If the previous answer was not applied using setLocalDescription,
   meaning the PeerConnection is still in the "have-remote-offer" state,
   the steps for generating an initial answer should be followed,
   subject to the following restriction:

   o  The fields of the "o=" line MUST stay the same except for the
      <session-version> field, which MUST increment if the session
      description changes in any way from the previously generated
      answer.

   If any session description was previously supplied to
   setLocalDescription, an answer is generated by following the steps in
   the "have-remote-offer" state above, along with these exceptions:

   o  The "s=" and "t=" lines MUST stay the same.

   o  Each "m=" and c=" line MUST be filled in with the port and address
      of the default candidate for the m= section, as described in
      [RFC5245], Section 4.3.  Note, however, that the m= line protocol
      need not match the default candidate, because this protocol value
      must instead match what was supplied in the offer, as described
      above.

   o  Each "a=ice-ufrag" and "a=ice-pwd" line MUST stay the same, unless
      the m= section is restarting, in which case new ICE credentials
      must be created as specified in [RFC5245], Section 9.2.1.1.  If
      the m= section is bundled into another m= section, it still MUST
      NOT contain any ICE credentials.

   o  Each "a=setup" line MUST use an "active" or "passive" role value
      consistent with the existing DTLS association, if the association
      is being continued by the offerer.

   o  RTCP multiplexing must be used, and an "a=rtcp-mux" line inserted
      if and only if the m= section previously used RTCP multiplexing.

   o  If the m= section is not bundled into another m= section and RTCP
      multiplexing is not active, an "a=rtcp" attribute line MUST be
      filled in with the port and address of the default RTCP candidate.
      If no RTCP candidates have yet been gathered, dummy values MUST be
      used, as described in the initial answer section above.




Uberti, et al.            Expires March 5, 2018                [Page 55]


Internet-Draft                    JSEP                    September 2017


   o  If the m= section is not bundled into another m= section, for each
      candidate that has been gathered during the most recent gathering
      phase (see Section 3.5.1), an "a=candidate" line MUST be added, as
      defined in [RFC5245], Section 4.3., paragraph 3.  If candidate
      gathering for the section has completed, an "a=end-of-candidates"
      attribute MUST be added, as described in [I-D.ietf-ice-trickle],
      Section 9.3.  If the m= section is bundled into another m=
      section, both "a=candidate" and "a=end-of-candidates" MUST be
      omitted.

   o  For RtpTransceivers that are not stopped, the "a=msid" line(s)
      MUST stay the same, regardless of changes to the transceiver's
      direction or track.  If no "a=msid" line is present in the current
      description, "a=msid" line(s) MUST be generated according to the
      same rules as for an initial answer.

5.3.3.  Options Handling

   The createAnswer method takes as a parameter an RTCAnswerOptions
   object.  The set of parameters for RTCAnswerOptions is different than
   those supported in RTCOfferOptions; the IceRestart option is
   unnecessary, as ICE credentials will automatically be changed for all
   m= sections where the offerer chose to perform ICE restart.

   The following options are supported in RTCAnswerOptions.

5.3.3.1.  VoiceActivityDetection

   Silence suppression in the answer is handled as described in
   Section 5.2.3.2, with one exception: if support for silence
   suppression was not indicated in the offer, the
   VoiceActivityDetection parameter has no effect, and the answer should
   be generated as if VoiceActivityDetection was set to false.  This is
   done on a per-codec basis (e.g., if the offerer somehow offered
   support for CN but set "usedtx=0" for Opus, setting
   VoiceActivityDetection to true would result in an answer with CN
   codecs and "usedtx=0").  The impact of this rule is that an answerer
   will not try to use silence suppression with any endpoint that does
   not offer it, making silence suppression support bilateral even with
   non-JSEP endpoints.

5.4.  Modifying an Offer or Answer

   The SDP returned from createOffer or createAnswer MUST NOT be changed
   before passing it to setLocalDescription.  If precise control over
   the SDP is needed, the aforementioned createOffer/createAnswer
   options or RtpTransceiver APIs MUST be used.




Uberti, et al.            Expires March 5, 2018                [Page 56]


Internet-Draft                    JSEP                    September 2017


   After calling setLocalDescription with an offer or answer, the
   application MAY modify the SDP to reduce its capabilities before
   sending it to the far side, as long as it follows the rules above
   that define a valid JSEP offer or answer.  Likewise, an application
   that has received an offer or answer from a peer MAY modify the
   received SDP, subject to the same constraints, before calling
   setRemoteDescription.

   As always, the application is solely responsible for what it sends to
   the other party, and all incoming SDP will be processed by the JSEP
   implementation to the extent of its capabilities.  It is an error to
   assume that all SDP is well-formed; however, one should be able to
   assume that any implementation of this specification will be able to
   process, as a remote offer or answer, unmodified SDP coming from any
   other implementation of this specification.

5.5.  Processing a Local Description

   When a SessionDescription is supplied to setLocalDescription, the
   following steps MUST be performed:

   o  If the description is of type "rollback", follow the processing
      defined in Section 5.7 and skip the processing described in the
      rest of this section.

   o  Otherwise, the type of the SessionDescription is checked against
      the current state of the PeerConnection:

      *  If the type is "offer", the PeerConnection state MUST be either
         "stable" or "have-local-offer".

      *  If the type is "pranswer" or "answer", the PeerConnection state
         MUST be either "have-remote-offer" or "have-local-pranswer".

   o  If the type is not correct for the current state, processing MUST
      stop and an error MUST be returned.

   o  The SessionDescription is then checked to ensure that its contents
      are identical to those generated in the last call to createOffer/
      createAnswer, and thus have not been altered, as discussed in
      Section 5.4; otherwise, processing MUST stop and an error MUST be
      returned.

   o  Next, the SessionDescription is parsed into a data structure, as
      described in Section 5.8 below.

   o  Finally, the parsed SessionDescription is applied as described in
      Section 5.9 below.



Uberti, et al.            Expires March 5, 2018                [Page 57]


Internet-Draft                    JSEP                    September 2017


5.6.  Processing a Remote Description

   When a SessionDescription is supplied to setRemoteDescription, the
   following steps MUST be performed:

   o  If the description is of type "rollback", follow the processing
      defined in Section 5.7 and skip the processing described in the
      rest of this section.

   o  Otherwise, the type of the SessionDescription is checked against
      the current state of the PeerConnection:

      *  If the type is "offer", the PeerConnection state MUST be either
         "stable" or "have-remote-offer".

      *  If the type is "pranswer" or "answer", the PeerConnection state
         MUST be either "have-local-offer" or "have-remote-pranswer".

   o  If the type is not correct for the current state, processing MUST
      stop and an error MUST be returned.

   o  Next, the SessionDescription is parsed into a data structure, as
      described in Section 5.8 below.  If parsing fails for any reason,
      processing MUST stop and an error MUST be returned.

   o  Finally, the parsed SessionDescription is applied as described in
      Section 5.10 below.

5.7.  Processing a Rollback

   A rollback may be performed if the PeerConnection is in any state
   except for "stable".  This means that both offers and provisional
   answers can be rolled back.  Rollback can only be used to cancel
   proposed changes; there is no support for rolling back from a stable
   state to a previous stable state.  If a rollback is attempted in the
   "stable" state, processing MUST stop and an error MUST be returned.
   Note that this implies that once the answerer has performed
   setLocalDescription with his answer, this cannot be rolled back.

   The effect of rollback MUST be the same regardless of whether
   setLocalDescription or setRemoteDescription is called.

   In order to process rollback, a JSEP implementation abandons the
   current offer/answer transaction, sets the signaling state to
   "stable", and sets the pending local and/or remote description (see
   Section 4.1.12 and Section 4.1.14) to null.  Any resources or
   candidates that were allocated by the abandoned local description are




Uberti, et al.            Expires March 5, 2018                [Page 58]


Internet-Draft                    JSEP                    September 2017


   discarded; any media that is received is processed according to the
   previous local and remote descriptions.

   A rollback disassociates any RtpTransceivers that were associated
   with m= sections by the application of the rolled-back session
   description (see Section 5.10 and Section 5.9).  This means that some
   RtpTransceivers that were previously associated will no longer be
   associated with any m= section; in such cases, the value of the
   RtpTransceiver's mid property MUST be set to null, and the mapping
   between the transceiver and its m= section index MUST be discarded.
   RtpTransceivers that were created by applying a remote offer that was
   subsequently rolled back MUST be stopped and removed from the
   PeerConnection.  However, a RtpTransceiver MUST NOT be removed if a
   track was attached to the RtpTransceiver via the addTrack method.
   This is so that an application may call addTrack, then call
   setRemoteDescription with an offer, then roll back that offer, then
   call createOffer and have a m= section for the added track appear in
   the generated offer.

5.8.  Parsing a Session Description

   The SDP contained in the session description object consists of a
   sequence of text lines, each containing a key-value expression, as
   described in [RFC4566], Section 5.  The SDP is read, line-by-line,
   and converted to a data structure that contains the deserialized
   information.  However, SDP allows many types of lines, not all of
   which are relevant to JSEP applications.  For each line, the
   implementation will first ensure it is syntactically correct
   according to its defining ABNF, check that it conforms to [RFC4566]
   and [RFC3264] semantics, and then either parse and store or discard
   the provided value, as described below.

   If any line is not well-formed, or cannot be parsed as described, the
   parser MUST stop with an error and reject the session description,
   even if the value is to be discarded.  This ensures that
   implementations do not accidentally misinterpret ambiguous SDP.

5.8.1.  Session-Level Parsing

   First, the session-level lines are checked and parsed.  These lines
   MUST occur in a specific order, and with a specific syntax, as
   defined in [RFC4566], Section 5.  Note that while the specific line
   types (e.g. "v=", "c=") MUST occur in the defined order, lines of the
   same type (typically "a=") can occur in any order.

   The following non-attribute lines are not meaningful in the JSEP
   context and MAY be discarded once they have been checked.




Uberti, et al.            Expires March 5, 2018                [Page 59]


Internet-Draft                    JSEP                    September 2017


      The "c=" line MUST be checked for syntax but its value is only
      used for ICE mismatch detection, as defined in [RFC5245],
      Section 6.1.  Note that JSEP implementations should never
      encounter this condition because ICE is required for WebRTC.

      The "i=", "u=", "e=", "p=", "t=", "r=", "z=", and "k=" lines are
      not used by this specification; they MUST be checked for syntax
      but their values are not used.

   The remaining non-attribute lines are processed as follows:

      The "v=" line MUST have a version of 0, as specified in [RFC4566],
      Section 5.1.

      The "o=" line MUST be parsed as specified in [RFC4566],
      Section 5.2.

      The "b=" line, if present, MUST be parsed as specified in
      [RFC4566], Section 5.8, and the bwtype and bandwidth values
      stored.

   Finally, the attribute lines are processed.  Specific processing MUST
   be applied for the following session-level attribute ("a=") lines:

   o  Any "a=group" lines are parsed as specified in [RFC5888],
      Section 5, and the group's semantics and mids are stored.

   o  If present, a single "a=ice-lite" line is parsed as specified in
      [RFC5245], Section 15.3, and a value indicating the presence of
      ice-lite is stored.

   o  If present, a single "a=ice-ufrag" line is parsed as specified in
      [RFC5245], Section 15.4, and the ufrag value is stored.

   o  If present, a single "a=ice-pwd" line is parsed as specified in
      [RFC5245], Section 15.4, and the password value is stored.

   o  If present, a single "a=ice-options" line is parsed as specified
      in [RFC5245], Section 15.5, and the set of specified options is
      stored.

   o  Any "a=fingerprint" lines are parsed as specified in [RFC8122],
      Section 5, and the set of fingerprint and algorithm values is
      stored.

   o  If present, a single "a=setup" line is parsed as specified in
      [RFC4145], Section 4, and the setup value is stored.




Uberti, et al.            Expires March 5, 2018                [Page 60]


Internet-Draft                    JSEP                    September 2017


   o  If present, a single "a=tls-id" line is parsed as specified in
      [I-D.ietf-mmusic-dtls-sdp] Section 5, and the tls-id value is
      stored.

   o  Any "a=identity" lines are parsed and the identity values stored
      for subsequent verification, as specified
      [I-D.ietf-rtcweb-security-arch], Section 5.

   o  Any "a=extmap" lines are parsed as specified in [RFC5285],
      Section 5, and their values are stored.

   Other attributes that are not relevant to JSEP may also be present,
   and implementations SHOULD process any that they recognize.  As
   required by [RFC4566], Section 5.13, unknown attribute lines MUST be
   ignored.

   Once all the session-level lines have been parsed, processing
   continues with the lines in m= sections.

5.8.2.  Media Section Parsing

   Like the session-level lines, the media section lines MUST occur in
   the specific order and with the specific syntax defined in [RFC4566],
   Section 5.

   The "m=" line itself MUST be parsed as described in [RFC4566],
   Section 5.14, and the media, port, proto, and fmt values stored.

   Following the "m=" line, specific processing MUST be applied for the
   following non-attribute lines:

   o  As with the "c=" line at the session level, the "c=" line MUST be
      parsed according to [RFC4566], Section 5.7, but its value is not
      used.

   o  The "b=" line, if present, MUST be parsed as specified in
      [RFC4566], Section 5.8, and the bwtype and bandwidth values
      stored.

   Specific processing MUST also be applied for the following attribute
   lines:

   o  If present, a single "a=ice-ufrag" line is parsed as specified in
      [RFC5245], Section 15.4, and the ufrag value is stored.

   o  If present, a single "a=ice-pwd" line is parsed as specified in
      [RFC5245], Section 15.4, and the password value is stored.




Uberti, et al.            Expires March 5, 2018                [Page 61]


Internet-Draft                    JSEP                    September 2017


   o  If present, a single "a=ice-options" line is parsed as specified
      in [RFC5245], Section 15.5, and the set of specified options is
      stored.

   o  Any "a=candidate" attributes MUST be parsed as specified in
      [RFC5245], Section 15.1, and their values stored.

   o  Any "a=remote-candidates" attributes MUST be parsed as specified
      in [RFC5245], Section 15.2, but their values are ignored.

   o  If present, a single "a=end-of-candidates" attribute MUST be
      parsed as specified in [I-D.ietf-ice-trickle], Section 8.2, and
      its presence or absence flagged and stored.

   o  Any "a=fingerprint" lines are parsed as specified in [RFC8122],
      Section 5, and the set of fingerprint and algorithm values is
      stored.

   If the "m=" proto value indicates use of RTP, as described in
   Section 5.1.2 above, the following attribute lines MUST be processed:

   o  The "m=" fmt value MUST be parsed as specified in [RFC4566],
      Section 5.14, and the individual values stored.

   o  Any "a=rtpmap" or "a=fmtp" lines MUST be parsed as specified in
      [RFC4566], Section 6, and their values stored.

   o  If present, a single "a=ptime" line MUST be parsed as described in
      [RFC4566], Section 6, and its value stored.

   o  If present, a single "a=maxptime" line MUST be parsed as described
      in [RFC4566], Section 6, and its value stored.

   o  If present, a single direction attribute line (e.g.  "a=sendrecv")
      MUST be parsed as described in [RFC4566], Section 6, and its value
      stored.

   o  Any "a=ssrc" attributes MUST be parsed as specified in [RFC5576],
      Section 4.1, and their values stored.

   o  Any "a=extmap" attributes MUST be parsed as specified in
      [RFC5285], Section 5, and their values stored.

   o  Any "a=rtcp-fb" attributes MUST be parsed as specified in
      [RFC4585], Section 4.2., and their values stored.






Uberti, et al.            Expires March 5, 2018                [Page 62]


Internet-Draft                    JSEP                    September 2017


   o  If present, a single "a=rtcp-mux" attribute MUST be parsed as
      specified in [RFC5761], Section 5.1.3, and its presence or absence
      flagged and stored.

   o  If present, a single "a=rtcp-mux-only" attribute MUST be parsed as
      specified in [I-D.ietf-mmusic-mux-exclusive], Section 3, and its
      presence or absence flagged and stored.

   o  If present, a single "a=rtcp-rsize" attribute MUST be parsed as
      specified in [RFC5506], Section 5, and its presence or absence
      flagged and stored.

   o  If present, a single "a=rtcp" attribute MUST be parsed as
      specified in [RFC3605], Section 2.1, but its value is ignored, as
      this information is superfluous when using ICE.

   o  If present, "a=msid" attributes MUST be parsed as specified in
      [I-D.ietf-mmusic-msid], Section 3.2, and their values stored.

   o  Any "a=imageattr" attributes MUST be parsed as specified in
      [RFC6236], Section 3, and their values stored.

   o  Any "a=rid" lines MUST be parsed as specified in
      [I-D.ietf-mmusic-rid], Section 10, and their values stored.

   o  If present, a single "a=simulcast" line MUST be parsed as
      specified in [I-D.ietf-mmusic-sdp-simulcast], and its values
      stored.

   Otherwise, if the "m=" proto value indicates use of SCTP, the
   following attribute lines MUST be processed:

   o  The "m=" fmt value MUST be parsed as specified in
      [I-D.ietf-mmusic-sctp-sdp], Section 4.3, and the application
      protocol value stored.

   o  An "a=sctp-port" attribute MUST be present, and it MUST be parsed
      as specified in [I-D.ietf-mmusic-sctp-sdp], Section 5.2, and the
      value stored.

   o  If present, a single "a=max-message-size" attribute MUST be parsed
      as specified in [I-D.ietf-mmusic-sctp-sdp], Section 6, and the
      value stored.  Otherwise, use the specified default.

   Other attributes that are not relevant to JSEP may also be present,
   and implementations SHOULD process any that they recognize.  As
   required by [RFC4566], Section 5.13, unknown attribute lines MUST be
   ignored.



Uberti, et al.            Expires March 5, 2018                [Page 63]


Internet-Draft                    JSEP                    September 2017


5.8.3.  Semantics Verification

   Assuming parsing completes successfully, the parsed description is
   then evaluated to ensure internal consistency as well as proper
   support for mandatory features.  Specifically, the following checks
   are performed:

   o  For each m= section, valid values for each of the mandatory-to-use
      features enumerated in Section 5.1.1 MUST be present.  These
      values MAY either be present at the media level, or inherited from
      the session level.

      *  ICE ufrag and password values, which MUST comply with the size
         limits specified in [RFC5245], Section 15.4.

      *  tls-id value, which MUST be set according to
         [I-D.ietf-mmusic-dtls-sdp], Section 5.  If this is a re-offer
         and the tls-id value is different from that presently in use,
         the DTLS connection is not being continued and the remote
         description MUST be part of an ICE restart, together with new
         ufrag and password values.  If this is an answer, the tls-id
         value, if present, MUST be the same as in the offer.

      *  DTLS setup value, which MUST be set according to the rules
         specified in [RFC5763], Section 5 and MUST be consistent with
         the selected role of the current DTLS connection, if one exists
         and is being continued.

      *  DTLS fingerprint values, where at least one fingerprint MUST be
         present.

   o  All RID values referenced in an "a=simulcast" line MUST exist as
      "a=rid" lines.

   o  Each m= section is also checked to ensure prohibited features are
      not used.

   o  If the RTP/RTCP multiplexing policy is "require", each m= section
      MUST contain an "a=rtcp-mux" attribute.  If an m= section contains
      an "a=rtcp-mux-only" attribute, that section MUST also contain an
      "a=rtcp-mux" attribute.

   o  If an m= section was present in the previous answer, the state of
      RTP/RTCP multiplexing MUST match what was previously negotiated.

   If this session description is of type "pranswer" or "answer", the
   following additional checks are applied:




Uberti, et al.            Expires March 5, 2018                [Page 64]


Internet-Draft                    JSEP                    September 2017


   o  The session description must follow the rules defined in
      [RFC3264], Section 6, including the requirement that the number of
      m= sections MUST exactly match the number of m= sections in the
      associated offer.

   o  For each m= section, the media type and protocol values MUST
      exactly match the media type and protocol values in the
      corresponding m= section in the associated offer.

   If any of the preceding checks failed, processing MUST stop and an
   error MUST be returned.

5.9.  Applying a Local Description

   The following steps are performed at the media engine level to apply
   a local description.  If an error is returned, the session MUST be
   restored to the state it was in before performing these steps.

   First, m= sections are processed.  For each m= section, the following
   steps MUST be performed; if any parameters are out of bounds, or
   cannot be applied, processing MUST stop and an error MUST be
   returned.

   o  If this m= section is new, begin gathering candidates for it, as
      defined in [RFC5245], Section 4.1.1, unless it is definitively
      being bundled (either this is an offer and the m= section is
      marked bundle-only, or it is an answer and the m= section is
      bundled into into another m= section.)

   o  Or, if the ICE ufrag and password values have changed, trigger the
      ICE agent to start an ICE restart, and begin gathering new
      candidates for the m= section as described in [RFC5245],
      Section 9.1.1.1.  If this description is an answer, also start
      checks on that media section as defined in [RFC5245],
      Section 9.3.1.1.

   o  If the m= section proto value indicates use of RTP:

      *  If there is no RtpTransceiver associated with this m= section,
         find one and associate it with this m= section according to the
         following steps.  Note that this situation will only occur when
         applying an offer.

         +  Find the RtpTransceiver that corresponds to this m= section,
            using the mapping between transceivers and m= section
            indices established when creating the offer.





Uberti, et al.            Expires March 5, 2018                [Page 65]


Internet-Draft                    JSEP                    September 2017


         +  Set the value of this RtpTransceiver's mid property to the
            MID of the m= section.

      *  If RTCP mux is indicated, prepare to demux RTP and RTCP from
         the RTP ICE component, as specified in [RFC5761],
         Section 5.1.3.

      *  For each specified RTP header extension, establish a mapping
         between the extension ID and URI, as described in [RFC5285],
         Section 6.

      *  If the MID header extension is supported, prepare to demux RTP
         streams intended for this m= section based on the MID header
         extension, as described in
         [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 15.

      *  For each specified media format, establish a mapping between
         the payload type and the actual media format, as described in
         [RFC3264], Section 6.1.  In addition, prepare to demux RTP
         streams intended for this m= section based on the media formats
         supported by this m= section, as described in
         [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 10.2.

      *  For each specified "rtx" media format, establish a mapping
         between the RTX payload type and its associated primary payload
         type, as described in [RFC4588], Sections 8.6 and 8.7.

      *  If the directional attribute is of type "sendrecv" or
         "recvonly", enable receipt and decoding of media.

   Finally, if this description is of type "pranswer" or "answer",
   follow the processing defined in Section 5.11 below.

5.10.  Applying a Remote Description

   The following steps are performed to apply a remote description.  If
   an error is returned, the session MUST be restored to the state it
   was in before performing these steps.

   If the answer contains any "a=ice-options" attributes where "trickle"
   is listed as an attribute, update the PeerConnection canTrickle
   property to be true.  Otherwise, set this property to false.

   The following steps MUST be performed for attributes at the session
   level; if any parameters are out of bounds, or cannot be applied,
   processing MUST stop and an error MUST be returned.





Uberti, et al.            Expires March 5, 2018                [Page 66]


Internet-Draft                    JSEP                    September 2017


   o  For any specified "CT" bandwidth value, set this as the limit for
      the maximum total bitrate for all m= sections, as specified in
      [RFC4566], Section 5.8.  Within this overall limit, the
      implementation can dynamically decide how to best allocate the
      available bandwidth between m= sections, respecting any specific
      limits that have been specified for individual m= sections.

   o  For any specified "RR" or "RS" bandwidth values, handle as
      specified in [RFC3556], Section 2.

   o  Any "AS" bandwidth value MUST be ignored, as the meaning of this
      construct at the session level is not well defined.

   For each m= section, the following steps MUST be performed; if any
   parameters are out of bounds, or cannot be applied, processing MUST
   stop and an error MUST be returned.

   o  If the ICE ufrag or password changed from the previous remote
      description: [RFC5245].

      *  If the description is of type "offer", the implementation MUST
         note that an ICE restart is needed, as described in [RFC5245],
         Section 9.1.1.1.

      *  If the description is of type "answer" or "pranswer", then
         check to see if the current local description is an ICE
         restart, and if not, generate an error.  If the PeerConnection
         state is "have-remote-pranswer", and the ICE ufrag or password
         changed from the previous provisional answer, then signal the
         ICE agent to discard any previous ICE check list state for the
         m= section.  Finally, signal the ICE agent to begin checks as
         described in [RFC5245], Section 9.3.1.1.

   o  If the current local description indicates an ICE restart, and
      either the ICE ufrag or password has not changed from the previous
      remote description, as prescribed by [RFC5245], Section 9.2.1.1,
      generate an error.

   o  Configure the ICE components associated with this media section to
      use the supplied ICE remote ufrag and password for their
      connectivity checks.

   o  Pair any supplied ICE candidates with any gathered local
      candidates, as described in [RFC5245], Section 5.7, and start
      connectivity checks with the appropriate credentials.






Uberti, et al.            Expires March 5, 2018                [Page 67]


Internet-Draft                    JSEP                    September 2017


   o  If an "a=end-of-candidates" attribute is present, process the end-
      of-candidates indication as described in [I-D.ietf-ice-trickle],
      Section 11.

   o  If the m= section proto value indicates use of RTP:

      *  If the m= section is being recycled (see Section 5.2.2),
         dissociate the currently associated RtpTransceiver by setting
         its mid property to null, and discard the mapping between the
         transceiver and its m= section index.

      *  If the m= section is not associated with any RtpTransceiver
         (possibly because it was dissociated in the previous step),
         either find an RtpTransceiver or create one according to the
         following steps:

         +  If the m= section is sendrecv or recvonly, and there are
            RtpTransceivers of the same type that were added to the
            PeerConnection by addTrack and are not associated with any
            m= section and are not stopped, find the first (according to
            the canonical order described in Section 5.2.1) such
            RtpTransceiver.

         +  If no RtpTransceiver was found in the previous step, create
            one with a recvonly direction.

         +  Associate the found or created RtpTransceiver with the m=
            section by setting the value of the RtpTransceiver's mid
            property to the MID of the m= section, and establish a
            mapping between the transceiver and the index of the m=
            section.  If the m= section does not include a MID (i.e.,
            the remote endpoint does not support the MID extension),
            generate a value for the RtpTransceiver mid property,
            following the guidance for "a=mid" mentioned in
            Section 5.2.1.

      *  For each specified media format that is also supported by the
         local implementation, establish a mapping between the specified
         payload type and the media format, as described in [RFC3264],
         Section 6.1.  Specifically, this means that the implementation
         records the payload type to be used in outgoing RTP packets
         when sending each specified media format, as well as the
         relative preference for each format that is indicated in their
         ordering.  If any indicated media format is not supported by
         the local implementation, it MUST be ignored.

      *  For each specified "rtx" media format, establish a mapping
         between the RTX payload type and its associated primary payload



Uberti, et al.            Expires March 5, 2018                [Page 68]


Internet-Draft                    JSEP                    September 2017


         type, as described in [RFC4588], Section 4.  If any referenced
         primary payload types are not present, this MUST result in an
         error.  Note that RTX payload types may refer to primary
         payload types which are not supported by the local media
         implementation, in which case, the RTX payload type MUST also
         be ignored.

      *  For each specified fmtp parameter that is supported by the
         local implementation, enable them on the associated media
         formats.

      *  For each specified SSRC that is signaled in the m= section,
         prepare to demux RTP streams intended for this m= section using
         that SSRC, as described in
         [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 10.2.

      *  For each specified RTP header extension that is also supported
         by the local implementation, establish a mapping between the
         extension ID and URI, as described in [RFC5285], Section 5.
         Specifically, this means that the implementation records the
         extension ID to be used in outgoing RTP packets when sending
         each specified header extension.  If any indicated RTP header
         extension is not supported by the local implementation, it MUST
         be ignored.

      *  For each specified RTCP feedback mechanism that is supported by
         the local implementation, enable them on the associated media
         formats.

      *  For any specified "TIAS" bandwidth value, set this value as a
         constraint on the maximum RTP bitrate to be used when sending
         media, as specified in [RFC3890].  If a "TIAS" value is not
         present, but an "AS" value is specified, generate a "TIAS"
         value using this formula:

         TIAS = AS * 1000 * 0.95 - (50 * 40 * 8)

         The 50 is based on 50 packets per second, the 40 is based on an
         estimate of total header size, the 1000 changes the unit from
         kbps to bps (as required by TIAS), and the 0.95 is to allocate
         5% to RTCP.  "TIAS" is used in preference to "AS" because it
         provides more accurate control of bandwidth.

      *  For any "RR" or "RS" bandwidth values, handle as specified in
         [RFC3556], Section 2.






Uberti, et al.            Expires March 5, 2018                [Page 69]


Internet-Draft                    JSEP                    September 2017


      *  Any specified "CT" bandwidth value MUST be ignored, as the
         meaning of this construct at the media level is not well
         defined.

      *  If the m= section is of type audio:

         +  For each specified "CN" media format, configure silence
            suppression for all supported media formats with the same
            clockrate, as described in [RFC3389], Section 5, except for
            formats that have their own internal silence suppression
            mechanisms.  Silence suppression for such formats (e.g.,
            Opus) is controlled via fmtp parameters, as discussed in
            Section 5.2.3.2.

         +  For each specified "telephone-event" media format, enable
            DTMF transmission for all supported media formats with the
            same clockrate, as described in [RFC4733], Section 2.5.1.2.
            If there are any supported media formats that do not have a
            corresponding telephone-event format, disable DTMF
            transmission for those formats.

         +  For any specified "ptime" value, configure the available
            media formats to use the specified packet size when sending.
            If the specified size is not supported for a media format,
            use the next closest value instead.

   Finally, if this description is of type "pranswer" or "answer",
   follow the processing defined in Section 5.11 below.

5.11.  Applying an Answer

   In addition to the steps mentioned above for processing a local or
   remote description, the following steps are performed when processing
   a description of type "pranswer" or "answer".

   For each m= section, the following steps MUST be performed:

   o  If the m= section has been rejected (i.e. port is set to zero in
      the answer), stop any reception or transmission of media for this
      section, and, unless a non-rejected m= section is bundled with
      this m= section, discard any associated ICE components, as
      described in [RFC5245], Section 9.2.1.3.

   o  If the remote DTLS fingerprint has been changed or the tls-id has
      changed, tear down the DTLS connection.  This includes the case
      when the PeerConnection state is "have-remote-pranswer".  If a
      DTLS connection needs to be torn down but the answer does not
      indicate an ICE restart or, in the case of "have-remote-pranswer",



Uberti, et al.            Expires March 5, 2018                [Page 70]


Internet-Draft                    JSEP                    September 2017


      new ICE credentials, an error MUST be generated.  If an ICE
      restart is performed without a change in tls-id or fingerprint,
      then the same DTLS connection is continued over the new ICE
      channel.

   o  If no valid DTLS connection exists, prepare to start a DTLS
      connection, using the specified roles and fingerprints, on any
      underlying ICE components, once they are active.

   o  If the m= section proto value indicates use of RTP:

      *  If the m= section references RTCP feedback mechanisms that were
         not present in the corresponding m= section in the offer, this
         indicates a negotiation problem and MUST result in an error.
         However, new media formats and new RTP header extension values
         are permitted in the answer, as described in [RFC3264],
         Section 7, and [RFC5285], Section 6.

      *  If the m= section has RTCP mux enabled, discard the RTCP ICE
         component, if one exists, and begin or continue muxing RTCP
         over the RTP ICE component, as specified in [RFC5761],
         Section 5.1.3.  Otherwise, prepare to transmit RTCP over the
         RTCP ICE component; if no RTCP ICE component exists, because
         RTCP mux was previously enabled, this MUST result in an error.

      *  If the m= section has reduced-size RTCP enabled, configure the
         RTCP transmission for this m= section to use reduced-size RTCP,
         as specified in [RFC5506].

      *  If the directional attribute in the answer indicates that the
         JSEP implementation should be sending media ("sendonly" for
         local answers, "recvonly" for remote answers, or "sendrecv" for
         either type of answer), choose the media format to send as the
         most preferred media format from the remote description that is
         also locally supported, as discussed in [RFC3264], Sections 6.1
         and 7, and start transmitting RTP media using that format once
         the underlying transport layers have been established.  If an
         SSRC has not already been chosen for this outgoing RTP stream,
         choose a random one.  If media is already being transmitted,
         the same SSRC SHOULD be used unless the clockrate of the new
         codec is different, in which case a new SSRC MUST be chosen, as
         specified in [RFC7160], Section 3.1.

      *  The payload type mapping from the remote description is used to
         determine payload types for the outgoing RTP streams, including
         the payload type for the send media format chosen above.  Any
         RTP header extensions that were negotiated should be included
         in the outgoing RTP streams, using the extension mapping from



Uberti, et al.            Expires March 5, 2018                [Page 71]


Internet-Draft                    JSEP                    September 2017


         the remote description; if the RID header extension has been
         negotiated, and RID values are specified, include the RID
         header extension in the outgoing RTP streams, as indicated in
         [I-D.ietf-mmusic-rid], Section 4.

      *  If the m= section is of type audio, and silence suppression was
         configured for the send media format as a result of processing
         the remote description, and is also enabled for that format in
         the local description, use silence suppression for outgoing
         media, in accordance with the guidance in Section 5.2.3.2.  If
         these conditions are not met, silence suppression MUST NOT be
         used for outgoing media.

      *  If simulcast has been negotiated, send the number of Source RTP
         Streams as specified in [I-D.ietf-mmusic-sdp-simulcast],
         Section 6.2.2.

      *  If the send media format chosen above has a corresponding "rtx"
         media format, or a FEC mechanism has been negotiated, establish
         a Redundancy RTP Stream with a random SSRC for each Source RTP
         Stream, and start or continue transmitting RTX/FEC packets as
         needed.

      *  If the send media format chosen above has a corresponding "red"
         media format of the same clockrate, allow redundant encoding
         using the specified format for resiliency purposes, as
         discussed in [I-D.ietf-rtcweb-fec], Section 3.2.  Note that
         unlike RTX or FEC media formats, the "red" format is
         transmitted on the Source RTP Stream, not the Redundancy RTP
         Stream.

      *  Enable the RTCP feedback mechanisms referenced in the media
         section for all Source RTP Streams using the specified media
         formats.  Specifically, begin or continue sending the requested
         feedback types and reacting to received feedback, as specified
         in [RFC4585], Section 4.2.  When sending RTCP feedback, follow
         the rules and recommendations from [RFC8108] Section 5.4.1, to
         select which SSRC to use.

      *  If the directional attribute in the answer indicates that the
         JSEP implementation should not be sending media ("recvonly" for
         local answers, "sendonly" for remote answers, or "inactive" for
         either type of answer) stop transmitting all RTP media, but
         continue sending RTCP, as described in [RFC3264], Section 5.1.

   o  If the m= section proto value indicates use of SCTP:





Uberti, et al.            Expires March 5, 2018                [Page 72]


Internet-Draft                    JSEP                    September 2017


      *  If an SCTP association exists, and the remote SCTP port has
         changed, discard the existing SCTP association.  This includes
         the case when the PeerConnection state is "have-remote-
         pranswer".

      *  If no valid SCTP association exists, prepare to initiate a SCTP
         association over the associated ICE component and DTLS
         connection, using the local SCTP port value from the local
         description, and the remote SCTP port value from the remote
         description, as described in [I-D.ietf-mmusic-sctp-sdp],
         Section 10.2.

   If the answer contains valid bundle groups, discard any ICE
   components for the m= sections that will be bundled onto the primary
   ICE components in each bundle, and begin muxing these m= sections
   accordingly, as described in
   [I-D.ietf-mmusic-sdp-bundle-negotiation], Section 8.2.

   If the description is of type "answer", and there are still remaining
   candidates in the ICE candidate pool, discard them.

6.  Processing RTP/RTCP

   When bundling, associating incoming RTP/RTCP with the proper m=
   section is defined in [I-D.ietf-mmusic-sdp-bundle-negotiation],
   Section 10.2.  When not bundling, the proper m= section is clear from
   the ICE component over which the RTP/RTCP is received.

   Once the proper m= section(s) are known, RTP/RTCP is delivered to the
   RtpTransceiver(s) associated with the m= section(s) and further
   processing of the RTP/RTCP is done at the RtpTransceiver level.  This
   includes using RID [I-D.ietf-mmusic-rid] to distinguish between
   multiple Encoded Streams, as well as determine which Source RTP
   stream should be repaired by a given Redundancy RTP stream.

7.  Examples

   Note that this example section shows several SDP fragments.  To
   format in 72 columns, some of the lines in SDP have been split into
   multiple lines, where leading whitespace indicates that a line is a
   continuation of the previous line.  In addition, some blank lines
   have been added to improve readability but are not valid in SDP.

   More examples of SDP for WebRTC call flows, including examples with
   IPv6 addresses, can be found in [I-D.ietf-rtcweb-sdp].






Uberti, et al.            Expires March 5, 2018                [Page 73]


Internet-Draft                    JSEP                    September 2017


7.1.  Simple Example

   This section shows a very simple example that sets up a minimal audio
   / video call between two JSEP endpoints without using trickle ICE.
   The example in the following section provides a more detailed example
   of what could happen in a JSEP session.

   The code flow below shows Alice's endpoint initiating the session to
   Bob's endpoint.  The messages from the JavaScript application in
   Alice's browser to the JavaScript in Bob's browser, abbreviated as
   AliceJS and BobJS respectively, are assumed to flow over some
   signaling protocol via a web server.  The JavaScript on both Alice's
   side and Bob's side waits for all candidates before sending the offer
   or answer, so the offers and answers are complete; trickle ICE is not
   used.  The user agents (JSEP implementations) in Alice and Bob's
   browsers, abbreviated as AliceUA and BobUA respectively, are using
   the default bundle policy of "balanced", and the default RTCP mux
   policy of "require".

































Uberti, et al.            Expires March 5, 2018                [Page 74]


Internet-Draft                    JSEP                    September 2017


//                  set up local media state
AliceJS->AliceUA:   create new PeerConnection
AliceJS->AliceUA:   addTrack with two tracks: audio and video
AliceJS->AliceUA:   createOffer to get offer
AliceJS->AliceUA:   setLocalDescription with offer
AliceUA->AliceJS:   multiple onicecandidate events with candidates

//                  wait for ICE gathering to complete
AliceUA->AliceJS:   onicecandidate event with null candidate
AliceJS->AliceUA:   get |offer-A1| from pendingLocalDescription

//                  |offer-A1| is sent over signaling protocol to Bob
AliceJS->WebServer: signaling with |offer-A1|
WebServer->BobJS:   signaling with |offer-A1|

//                  |offer-A1| arrives at Bob
BobJS->BobUA:       create a PeerConnection
BobJS->BobUA:       setRemoteDescription with |offer-A1|
BobUA->BobJS:       ontrack events for audio and video tracks

//                  Bob accepts call
BobJS->BobUA:       addTrack with local tracks
BobJS->BobUA:       createAnswer
BobJS->BobUA:       setLocalDescription with answer
BobUA->BobJS:       multiple onicecandidate events with candidates

//                  wait for ICE gathering to complete
BobUA->BobJS:       onicecandidate event with null candidate
BobJS->BobUA:       get |answer-A1| from currentLocalDescription

//                  |answer-A1| is sent over signaling protocol to Alice
BobJS->WebServer:   signaling with |answer-A1|
WebServer->AliceJS: signaling with |answer-A1|

//                  |answer-A1| arrives at Alice
AliceJS->AliceUA:   setRemoteDescription with |answer-A1|
AliceUA->AliceJS:   ontrack events for audio and video tracks

//                  media flows
BobUA->AliceUA:     media sent from Bob to Alice
AliceUA->BobUA:     media sent from Alice to Bob


   The SDP for |offer-A1| looks like:


   v=0
   o=- 4962303333179871722 1 IN IP4 0.0.0.0



Uberti, et al.            Expires March 5, 2018                [Page 75]


Internet-Draft                    JSEP                    September 2017


   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 v1
   a=group:LS a1 v1

   m=audio 10100 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 203.0.113.100
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:47017fee-b6c1-4162-929c-a25110252400
          f83006c5-a0ff-4e0a-9ed9-d3e6747be7d9
   a=ice-ufrag:ETEn
   a=ice-pwd:OtSK0WpNtpUjkY4+86js7ZQl
   a=fingerprint:sha-256
                 19:E2:1C:3B:4B:9F:81:E6:B8:5C:F4:A5:A8:D8:73:04:
                 BB:05:2F:70:9F:04:A9:0E:05:E9:26:33:E8:70:88:A2
   a=setup:actpass
   a=tls-id:1
   a=rtcp:10101 IN IP4 203.0.113.100
   a=rtcp-mux
   a=rtcp-rsize
   a=candidate:1 1 udp 2113929471 203.0.113.100 10100 typ host
   a=candidate:1 2 udp 2113929470 203.0.113.100 10101 typ host
   a=end-of-candidates

   m=video 10102 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 203.0.113.100
   a=mid:v1
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid



Uberti, et al.            Expires March 5, 2018                [Page 76]


Internet-Draft                    JSEP                    September 2017


   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:47017fee-b6c1-4162-929c-a25110252400
          f30bdb4a-5db8-49b5-bcdc-e0c9a23172e0
   a=ice-ufrag:BGKk
   a=ice-pwd:mqyWsAjvtKwTGnvhPztQ9mIf
   a=fingerprint:sha-256
                 19:E2:1C:3B:4B:9F:81:E6:B8:5C:F4:A5:A8:D8:73:04:
                 BB:05:2F:70:9F:04:A9:0E:05:E9:26:33:E8:70:88:A2
   a=setup:actpass
   a=tls-id:1
   a=rtcp:10103 IN IP4 203.0.113.100
   a=rtcp-mux
   a=rtcp-rsize
   a=candidate:1 1 udp 2113929471 203.0.113.100 10102 typ host
   a=candidate:1 2 udp 2113929470 203.0.113.100 10103 typ host
   a=end-of-candidates


   The SDP for |answer-A1| looks like:


   v=0
   o=- 6729291447651054566 1 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 v1
   a=group:LS a1 v1

   m=audio 10200 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 203.0.113.200
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:61317484-2ed4-49d7-9eb7-1414322a7aae
          5a7b57b8-f043-4bd1-a45d-09d4dfa31226



Uberti, et al.            Expires March 5, 2018                [Page 77]


Internet-Draft                    JSEP                    September 2017


   a=ice-ufrag:6sFv
   a=ice-pwd:cOTZKZNVlO9RSGsEGM63JXT2
   a=fingerprint:sha-256
                 6B:8B:F0:65:5F:78:E2:51:3B:AC:6F:F3:3F:46:1B:35:
                 DC:B8:5F:64:1A:24:C2:43:F0:A1:58:D0:A1:2C:19:08
   a=setup:active
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-rsize
   a=candidate:1 1 udp 2113929471 203.0.113.200 10200 typ host
   a=end-of-candidates

   m=video 10200 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 203.0.113.200
   a=mid:v1
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:61317484-2ed4-49d7-9eb7-1414322a7aae
          4ea4d4a1-2fda-4511-a9cc-1b32c2e59552


7.2.  Detailed Example

   This section shows a more involved example of a session between two
   JSEP endpoints.  Trickle ICE is used in full trickle mode, with a
   bundle policy of "max-bundle", an RTCP mux policy of "require", and a
   single TURN server.  Initially, both Alice and Bob establish an audio
   channel and a data channel.  Later, Bob adds two video flows, one for
   his video feed, and one for screensharing, both supporting FEC, and
   with the video feed configured for simulcast.  Alice accepts these
   video flows, but does not add video flows of her own, so they are
   handled as recvonly.  Alice also specifies a maximum video decoder
   resolution.


  //                  set up local media state
  AliceJS->AliceUA:   create new PeerConnection



Uberti, et al.            Expires March 5, 2018                [Page 78]


Internet-Draft                    JSEP                    September 2017


  AliceJS->AliceUA:   addTrack with an audio track
  AliceJS->AliceUA:   createDataChannel to get data channel
  AliceJS->AliceUA:   createOffer to get |offer-B1|
  AliceJS->AliceUA:   setLocalDescription with |offer-B1|

  //                  |offer-B1| is sent over signaling protocol to Bob
  AliceJS->WebServer: signaling with |offer-B1|
  WebServer->BobJS:   signaling with |offer-B1|

  //                  |offer-B1| arrives at Bob
  BobJS->BobUA:       create a PeerConnection
  BobJS->BobUA:       setRemoteDescription with |offer-B1|
  BobUA->BobJS:       ontrack with audio track from Alice

  //                  candidates are sent to Bob
  AliceUA->AliceJS:   onicecandidate (host) |offer-B1-candidate-1|
  AliceJS->WebServer: signaling with |offer-B1-candidate-1|
  AliceUA->AliceJS:   onicecandidate (srflx) |offer-B1-candidate-2|
  AliceJS->WebServer: signaling with |offer-B1-candidate-2|
  AliceUA->AliceJS:   onicecandidate (relay) |offer-B1-candidate-3|
  AliceJS->WebServer: signaling with |offer-B1-candidate-3|

  WebServer->BobJS:   signaling with |offer-B1-candidate-1|
  BobJS->BobUA:       addIceCandidate with |offer-B1-candidate-1|
  WebServer->BobJS:   signaling with |offer-B1-candidate-2|
  BobJS->BobUA:       addIceCandidate with |offer-B1-candidate-2|
  WebServer->BobJS:   signaling with |offer-B1-candidate-3|
  BobJS->BobUA:       addIceCandidate with |offer-B1-candidate-3|

  //                  Bob accepts call
  BobJS->BobUA:       addTrack with local audio
  BobJS->BobUA:       createDataChannel to get data channel
  BobJS->BobUA:       createAnswer to get |answer-B1|
  BobJS->BobUA:       setLocalDescription with |answer-B1|

  //                  |answer-B1| is sent to Alice
  BobJS->WebServer:   signaling with |answer-B1|
  WebServer->AliceJS: signaling with |answer-B1|
  AliceJS->AliceUA:   setRemoteDescription with |answer-B1|
  AliceUA->AliceJS:   ontrack event with audio track from Bob

  //                  candidates are sent to Alice
  BobUA->BobJS:       onicecandidate (host) |answer-B1-candidate-1|
  BobJS->WebServer:   signaling with |answer-B1-candidate-1|
  BobUA->BobJS:       onicecandidate (srflx) |answer-B1-candidate-2|
  BobJS->WebServer:   signaling with |answer-B1-candidate-2|
  BobUA->BobJS:       onicecandidate (relay) |answer-B1-candidate-3|
  BobJS->WebServer:   signaling with |answer-B1-candidate-3|



Uberti, et al.            Expires March 5, 2018                [Page 79]


Internet-Draft                    JSEP                    September 2017


  WebServer->AliceJS: signaling with |answer-B1-candidate-1|
  AliceJS->AliceUA:   addIceCandidate with |answer-B1-candidate-1|
  WebServer->AliceJS: signaling with |answer-B1-candidate-2|
  AliceJS->AliceUA:   addIceCandidate with |answer-B1-candidate-2|
  WebServer->AliceJS: signaling with |answer-B1-candidate-3|
  AliceJS->AliceUA:   addIceCandidate with |answer-B1-candidate-3|

  //                  data channel opens
  BobUA->BobJS:       ondatachannel event
  AliceUA->AliceJS:   ondatachannel event
  BobUA->BobJS:       onopen
  AliceUA->AliceJS:   onopen

  //                  media is flowing between endpoints
  BobUA->AliceUA:     audio+data sent from Bob to Alice
  AliceUA->BobUA:     audio+data sent from Alice to Bob

  //                  some time later Bob adds two video streams
  //                  note, no candidates exchanged, because of bundle
  BobJS->BobUA:       addTrack with first video stream
  BobJS->BobUA:       addTrack with second video stream
  BobJS->BobUA:       createOffer to get |offer-B2|
  BobJS->BobUA:       setLocalDescription with |offer-B2|

  //                  |offer-B2| is sent to Alice
  BobJS->WebServer:   signaling with |offer-B2|
  WebServer->AliceJS: signaling with |offer-B2|
  AliceJS->AliceUA:   setRemoteDescription with |offer-B2|
  AliceUA->AliceJS:   ontrack event with first video track
  AliceUA->AliceJS:   ontrack event with second video track
  AliceJS->AliceUA:   createAnswer to get |answer-B2|
  AliceJS->AliceUA:   setLocalDescription with |answer-B2|

  //                  |answer-B2| is sent over signaling protocol to Bob
  AliceJS->WebServer: signaling with |answer-B2|
  WebServer->BobJS:   signaling with |answer-B2|
  BobJS->BobUA:       setRemoteDescription with |answer-B2|

  //                  media is flowing between endpoints
  BobUA->AliceUA:     audio+video+data sent from Bob to Alice
  AliceUA->BobUA:     audio+video+data sent from Alice to Bob


   The SDP for |offer-B1| looks like:







Uberti, et al.            Expires March 5, 2018                [Page 80]


Internet-Draft                    JSEP                    September 2017


   v=0
   o=- 4962303333179871723 1 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 d1

   m=audio 9 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 0.0.0.0
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:57017fee-b6c1-4162-929c-a25110252400
          e83006c5-a0ff-4e0a-9ed9-d3e6747be7d9
   a=ice-ufrag:ATEn
   a=ice-pwd:AtSK0WpNtpUjkY4+86js7ZQl
   a=fingerprint:sha-256
                 29:E2:1C:3B:4B:9F:81:E6:B8:5C:F4:A5:A8:D8:73:04:
                 BB:05:2F:70:9F:04:A9:0E:05:E9:26:33:E8:70:88:A2
   a=setup:actpass
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize

   m=application 0 UDP/DTLS/SCTP webrtc-datachannel
   c=IN IP4 0.0.0.0
   a=mid:d1
   a=sctp-port:5000
   a=max-message-size:65536
   a=bundle-only


   |offer-B1-candidate-1| looks like:








Uberti, et al.            Expires March 5, 2018                [Page 81]


Internet-Draft                    JSEP                    September 2017


   ufrag ATEn
   index 0
   mid   a1
   attr  candidate:1 1 udp 2113929471 203.0.113.100 10100 typ host


   |offer-B1-candidate-2| looks like:


   ufrag ATEn
   index 0
   mid   a1
   attr  candidate:1 1 udp 1845494015 198.51.100.100 11100 typ srflx
                   raddr 203.0.113.100 rport 10100


   |offer-B1-candidate-3| looks like:


   ufrag ATEn
   index 0
   mid   a1
   attr  candidate:1 1 udp 255 192.0.2.100 12100 typ relay
                   raddr 198.51.100.100 rport 11100


   The SDP for |answer-B1| looks like:
























Uberti, et al.            Expires March 5, 2018                [Page 82]


Internet-Draft                    JSEP                    September 2017


   v=0
   o=- 7729291447651054566 1 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 d1

   m=audio 9 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 0.0.0.0
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:71317484-2ed4-49d7-9eb7-1414322a7aae
          6a7b57b8-f043-4bd1-a45d-09d4dfa31226
   a=ice-ufrag:7sFv
   a=ice-pwd:dOTZKZNVlO9RSGsEGM63JXT2
   a=fingerprint:sha-256
                 7B:8B:F0:65:5F:78:E2:51:3B:AC:6F:F3:3F:46:1B:35:
                 DC:B8:5F:64:1A:24:C2:43:F0:A1:58:D0:A1:2C:19:08
   a=setup:active
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize

   m=application 9 UDP/DTLS/SCTP webrtc-datachannel
   c=IN IP4 0.0.0.0
   a=mid:d1
   a=sctp-port:5000
   a=max-message-size:65536


   |answer-B1-candidate-1| looks like:









Uberti, et al.            Expires March 5, 2018                [Page 83]


Internet-Draft                    JSEP                    September 2017


   ufrag 7sFv
   index 0
   mid   a1
   attr  candidate:1 1 udp 2113929471 203.0.113.200 10200 typ host


   |answer-B1-candidate-2| looks like:


   ufrag 7sFv
   index 0
   mid   a1
   attr  candidate:1 1 udp 1845494015 198.51.100.200 11200 typ srflx
                   raddr 203.0.113.200 rport 10200


   |answer-B1-candidate-3| looks like:


   ufrag 7sFv
   index 0
   mid   a1
   attr  candidate:1 1 udp 255 192.0.2.200 12200 typ relay
                   raddr 198.51.100.200 rport 11200


   The SDP for |offer-B2| is shown below.  In addition to the new m=
   sections for video, both of which are offering FEC, and one of which
   is offering simulcast, note the increment of the version number in
   the o= line, changes to the c= line, indicating the local candidate
   that was selected, and the inclusion of gathered candidates as
   a=candidate lines.


   v=0
   o=- 7729291447651054566 2 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 d1 v1 v2
   a=group:LS a1 v1

   m=audio 12200 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 192.0.2.200
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000



Uberti, et al.            Expires March 5, 2018                [Page 84]


Internet-Draft                    JSEP                    September 2017


   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:71317484-2ed4-49d7-9eb7-1414322a7aae
          6a7b57b8-f043-4bd1-a45d-09d4dfa31226
   a=ice-ufrag:7sFv
   a=ice-pwd:dOTZKZNVlO9RSGsEGM63JXT2
   a=fingerprint:sha-256
                 7B:8B:F0:65:5F:78:E2:51:3B:AC:6F:F3:3F:46:1B:35:
                 DC:B8:5F:64:1A:24:C2:43:F0:A1:58:D0:A1:2C:19:08
   a=setup:actpass
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize
   a=candidate:1 1 udp 2113929471 203.0.113.200 10200 typ host
   a=candidate:1 1 udp 1845494015 198.51.100.200 11200 typ srflx
               raddr 203.0.113.200 rport 10200
   a=candidate:1 1 udp 255 192.0.2.200 12200 typ relay
               raddr 198.51.100.200 rport 11200
   a=end-of-candidates

   m=application 12200 UDP/DTLS/SCTP webrtc-datachannel
   c=IN IP4 192.0.2.200
   a=mid:d1
   a=sctp-port:5000
   a=max-message-size:65536

   m=video 12200 UDP/TLS/RTP/SAVPF 100 101 102 103 104
   c=IN IP4 192.0.2.200
   a=mid:v1
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=rtpmap:104 flexfec/90000
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir



Uberti, et al.            Expires March 5, 2018                [Page 85]


Internet-Draft                    JSEP                    September 2017


   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:71317484-2ed4-49d7-9eb7-1414322a7aae
          5ea4d4a1-2fda-4511-a9cc-1b32c2e59552
   a=rid:1 send
   a=rid:2 send
   a=rid:3 send
   a=simulcast:send 1;2;3

   m=video 12200 UDP/TLS/RTP/SAVPF 100 101 102 103 104
   c=IN IP4 192.0.2.200
   a=mid:v2
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=rtpmap:104 flexfec/90000
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:81317484-2ed4-49d7-9eb7-1414322a7aae
          6ea4d4a1-2fda-4511-a9cc-1b32c2e59552


   The SDP for |answer-B2| is shown below.  In addition to the
   acceptance of the video m= sections, the use of a=recvonly to
   indicate one-way video, and the use of a=imageattr to limit the
   received resolution, note the use of setup:passive to maintain the
   existing DTLS roles.


   v=0
   o=- 4962303333179871723 2 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 d1 v1 v2
   a=group:LS a1 v1

   m=audio 12100 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 192.0.2.100
   a=mid:a1



Uberti, et al.            Expires March 5, 2018                [Page 86]


Internet-Draft                    JSEP                    September 2017


   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:57017fee-b6c1-4162-929c-a25110252400
          e83006c5-a0ff-4e0a-9ed9-d3e6747be7d9
   a=ice-ufrag:ATEn
   a=ice-pwd:AtSK0WpNtpUjkY4+86js7ZQl
   a=fingerprint:sha-256
                 29:E2:1C:3B:4B:9F:81:E6:B8:5C:F4:A5:A8:D8:73:04:
                 BB:05:2F:70:9F:04:A9:0E:05:E9:26:33:E8:70:88:A2
   a=setup:passive
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize
   a=candidate:1 1 udp 2113929471 203.0.113.100 10100 typ host
   a=candidate:1 1 udp 1845494015 198.51.100.100 11100 typ srflx
               raddr 203.0.113.100 rport 10100
   a=candidate:1 1 udp 255 192.0.2.100 12100 typ relay
               raddr 198.51.100.100 rport 11100
   a=end-of-candidates

   m=application 12100 UDP/DTLS/SCTP webrtc-datachannel
   c=IN IP4 192.0.2.100
   a=mid:d1
   a=sctp-port:5000
   a=max-message-size:65536

   m=video 12100 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 192.0.2.100
   a=mid:v1
   a=recvonly
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=imageattr:100 recv [x=[48:1920],y=[48:1080],q=1.0]



Uberti, et al.            Expires March 5, 2018                [Page 87]


Internet-Draft                    JSEP                    September 2017


   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli

   m=video 12100 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 192.0.2.100
   a=mid:v2
   a=recvonly
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=imageattr:100 recv [x=[48:1920],y=[48:1080],q=1.0]
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli


7.3.  Early Transport Warmup Example

   This example demonstrates the early warmup technique described in
   Section 4.1.8.1.  Here, Alice's endpoint sends an offer to Bob's
   endpoint to start an audio/video call.  Bob immediately responds with
   an answer that accepts the audio/video m= sections, but marks them as
   sendonly (from his perspective), meaning that Alice will not yet send
   media.  This allows the JSEP implementation to start negotiating ICE
   and DTLS immediately.  Bob's endpoint then prompts him to answer the
   call, and when he does, his endpoint sends a second offer which
   enables the audio and video m= sections, and thereby bidirectional
   media transmission.  The advantage of such a flow is that as soon as
   the first answer is received, the implementation can proceed with ICE
   and DTLS negotiation and establish the session transport.  If the
   transport setup completes before the second offer is sent, then media
   can be transmitted immediately by the callee immediately upon
   answering the call, minimizing perceived post-dial-delay.  The second
   offer/answer exchange can also change the preferred codecs or other
   session parameters.

   This example also makes use of the "relay" ICE candidate policy
   described in Section 3.5.3 to minimize the ICE gathering and checking
   needed.



Uberti, et al.            Expires March 5, 2018                [Page 88]


Internet-Draft                    JSEP                    September 2017


//                  set up local media state
AliceJS->AliceUA:   create new PeerConnection with "relay" ICE policy
AliceJS->AliceUA:   addTrack with two tracks: audio and video
AliceJS->AliceUA:   createOffer to get |offer-C1|
AliceJS->AliceUA:   setLocalDescription with |offer-C1|

//                  |offer-C1| is sent over signaling protocol to Bob
AliceJS->WebServer: signaling with |offer-C1|
WebServer->BobJS:   signaling with |offer-C1|

//                  |offer-C1| arrives at Bob
BobJS->BobUA:       create new PeerConnection with "relay" ICE policy
BobJS->BobUA:       setRemoteDescription with |offer-C1|
BobUA->BobJS:       ontrack events for audio and video

//                  a relay candidate is sent to Bob
AliceUA->AliceJS:   onicecandidate (relay) |offer-C1-candidate-1|
AliceJS->WebServer: signaling with |offer-C1-candidate-1|

WebServer->BobJS:   signaling with |offer-C1-candidate-1|
BobJS->BobUA:       addIceCandidate with |offer-C1-candidate-1|

//                  Bob prepares an early answer to warmup the transport
BobJS->BobUA:       addTransceiver with null audio and video tracks
BobJS->BobUA:       transceiver.setDirection(sendonly) for both
BobJS->BobUA:       createAnswer
BobJS->BobUA:       setLocalDescription with answer

//                  |answer-C1| is sent over signaling protocol to Alice
BobJS->WebServer:   signaling with |answer-C1|
WebServer->AliceJS: signaling with |answer-C1|

//                  |answer-C1| (sendonly) arrives at Alice
AliceJS->AliceUA:   setRemoteDescription with |answer-C1|
AliceUA->AliceJS:   ontrack events for audio and video

//                  a relay candidate is sent to Alice
BobUA->BobJS:       onicecandidate (relay) |answer-B1-candidate-1|
BobJS->WebServer:   signaling with |answer-B1-candidate-1|

WebServer->AliceJS: signaling with |answer-B1-candidate-1|
AliceJS->AliceUA:   addIceCandidate with |answer-B1-candidate-1|

//                  ICE and DTLS establish while call is ringing

//                  Bob accepts call, starts media, and sends new offer
BobJS->BobUA:       transceiver.setTrack with audio and video tracks
BobUA->AliceUA:     media sent from Bob to Alice



Uberti, et al.            Expires March 5, 2018                [Page 89]


Internet-Draft                    JSEP                    September 2017


BobJS->BobUA:       transceiver.setDirection(sendrecv) for both
                    transceivers
BobJS->BobUA:       createOffer
BobJS->BobUA:       setLocalDescription with offer

//                  |offer-C2| is sent over signaling protocol to Alice
BobJS->WebServer:   signaling with |offer-C2|
WebServer->AliceJS: signaling with |offer-C2|

//                  |offer-C2| (sendrecv) arrives at Alice
AliceJS->AliceUA:   setRemoteDescription with |offer-C2|
AliceJS->AliceUA:   createAnswer
AliceJS->AliceUA:   setLocalDescription with |answer-C2|
AliceUA->BobUA:     media sent from Alice to Bob

//                  |answer-C2| is sent over signaling protocol to Bob
AliceJS->WebServer: signaling with |answer-C2|
WebServer->BobJS:   signaling with |answer-C2|
BobJS->BobUA:       setRemoteDescription with |answer-C2|


   The SDP for |offer-C1| looks like:


   v=0
   o=- 1070771854436052752 1 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 v1
   a=group:LS a1 v1

   m=audio 9 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 0.0.0.0
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:bbce3ba6-abfc-ac63-d00a-e15b286f8fce
          e80098db-7159-3c06-229a-00df2a9b3dbc



Uberti, et al.            Expires March 5, 2018                [Page 90]


Internet-Draft                    JSEP                    September 2017


   a=ice-ufrag:4ZcD
   a=ice-pwd:ZaaG6OG7tCn4J/lehAGz+HHD
   a=fingerprint:sha-256
                 C4:68:F8:77:6A:44:F1:98:6D:7C:9F:47:EB:E3:34:A4:
                 0A:AA:2D:49:08:28:70:2E:1F:AE:18:7D:4E:3E:66:BF
   a=setup:actpass
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize

   m=video 0 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 0.0.0.0
   a=mid:v1
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:bbce3ba6-abfc-ac63-d00a-e15b286f8fce
          ac701365-eb06-42df-cc93-7f22bc308789
   a=bundle-only


   |offer-C1-candidate-1| looks like:


   ufrag 4ZcD
   index 0
   mid   a1
   attr  candidate:1 1 udp 255 192.0.2.100 12100 typ relay
                   raddr 0.0.0.0 rport 0


   The SDP for |answer-C1| looks like:


   v=0
   o=- 6386516489780559513 1 IN IP4 0.0.0.0
   s=-



Uberti, et al.            Expires March 5, 2018                [Page 91]


Internet-Draft                    JSEP                    September 2017


   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 v1
   a=group:LS a1 v1

   m=audio 9 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 0.0.0.0
   a=mid:a1
   a=sendonly
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:751f239e-4ae0-c549-aa3d-890de772998b
          04b5a445-82cc-c9e8-9ffe-c24d0ef4b0ff
   a=ice-ufrag:TpaA
   a=ice-pwd:t2Ouhc67y8JcCaYZxUUTgKw/
   a=fingerprint:sha-256
                 A2:F3:A5:6D:4C:8C:1E:B2:62:10:4A:F6:70:61:C4:FC:
                 3C:E0:01:D6:F3:24:80:74:DA:7C:3E:50:18:7B:CE:4D
   a=setup:active
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize

   m=video 9 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 0.0.0.0
   a=mid:v1
   a=sendonly
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli



Uberti, et al.            Expires March 5, 2018                [Page 92]


Internet-Draft                    JSEP                    September 2017


   a=msid:751f239e-4ae0-c549-aa3d-890de772998b
          39292672-c102-d075-f580-5826f31ca958


   |answer-C1-candidate-1| looks like:


   ufrag TpaA
   index 0
   mid   a1
   attr  candidate:1 1 udp 255 192.0.2.200 12200 typ relay
                   raddr 0.0.0.0 rport 0


   The SDP for |offer-C2| looks like:


   v=0
   o=- 6386516489780559513 2 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 v1
   a=group:LS a1 v1

   m=audio 12200 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 192.0.2.200
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15
   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:751f239e-4ae0-c549-aa3d-890de772998b
          04b5a445-82cc-c9e8-9ffe-c24d0ef4b0ff
   a=ice-ufrag:TpaA
   a=ice-pwd:t2Ouhc67y8JcCaYZxUUTgKw/
   a=fingerprint:sha-256
                 A2:F3:A5:6D:4C:8C:1E:B2:62:10:4A:F6:70:61:C4:FC:
                 3C:E0:01:D6:F3:24:80:74:DA:7C:3E:50:18:7B:CE:4D
   a=setup:actpass
   a=tls-id:1



Uberti, et al.            Expires March 5, 2018                [Page 93]


Internet-Draft                    JSEP                    September 2017


   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize
   a=candidate:1 1 udp 255 192.0.2.200 12200 typ relay
               raddr 0.0.0.0 rport 0
   a=end-of-candidates

   m=video 12200 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 192.0.2.200
   a=mid:v1
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:751f239e-4ae0-c549-aa3d-890de772998b
          39292672-c102-d075-f580-5826f31ca958


   The SDP for |answer-C2| looks like:


   v=0
   o=- 1070771854436052752 2 IN IP4 0.0.0.0
   s=-
   t=0 0
   a=ice-options:trickle
   a=group:BUNDLE a1 v1
   a=group:LS a1 v1

   m=audio 12100 UDP/TLS/RTP/SAVPF 96 0 8 97 98
   c=IN IP4 192.0.2.100
   a=mid:a1
   a=sendrecv
   a=rtpmap:96 opus/48000/2
   a=rtpmap:0 PCMU/8000
   a=rtpmap:8 PCMA/8000
   a=rtpmap:97 telephone-event/8000
   a=rtpmap:98 telephone-event/48000
   a=fmtp:97 0-15



Uberti, et al.            Expires March 5, 2018                [Page 94]


Internet-Draft                    JSEP                    September 2017


   a=fmtp:98 0-15
   a=maxptime:120
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:2 urn:ietf:params:rtp-hdrext:ssrc-audio-level
   a=msid:bbce3ba6-abfc-ac63-d00a-e15b286f8fce
          e80098db-7159-3c06-229a-00df2a9b3dbc
   a=ice-ufrag:4ZcD
   a=ice-pwd:ZaaG6OG7tCn4J/lehAGz+HHD
   a=fingerprint:sha-256
                 C4:68:F8:77:6A:44:F1:98:6D:7C:9F:47:EB:E3:34:A4:
                 0A:AA:2D:49:08:28:70:2E:1F:AE:18:7D:4E:3E:66:BF
   a=setup:passive
   a=tls-id:1
   a=rtcp-mux
   a=rtcp-mux-only
   a=rtcp-rsize
   a=candidate:1 1 udp 255 192.0.2.100 12100 typ relay
               raddr 0.0.0.0 rport 0
   a=end-of-candidates

   m=video 12100 UDP/TLS/RTP/SAVPF 100 101 102 103
   c=IN IP4 192.0.2.100
   a=mid:v1
   a=sendrecv
   a=rtpmap:100 VP8/90000
   a=rtpmap:101 H264/90000
   a=fmtp:101 packetization-mode=1;profile-level-id=42e01f
   a=rtpmap:102 rtx/90000
   a=fmtp:102 apt=100
   =rtpmap:103 rtx/90000
   a=fmtp:103 apt=101
   a=extmap:1 urn:ietf:params:rtp-hdrext:sdes:mid
   a=extmap:3 urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id
   a=rtcp-fb:100 ccm fir
   a=rtcp-fb:100 nack
   a=rtcp-fb:100 nack pli
   a=msid:bbce3ba6-abfc-ac63-d00a-e15b286f8fce
          ac701365-eb06-42df-cc93-7f22bc308789


8.  Security Considerations

   The IETF has published separate documents
   [I-D.ietf-rtcweb-security-arch] [I-D.ietf-rtcweb-security] describing
   the security architecture for WebRTC as a whole.  The remainder of
   this section describes security considerations for this document.





Uberti, et al.            Expires March 5, 2018                [Page 95]


Internet-Draft                    JSEP                    September 2017


   While formally the JSEP interface is an API, it is better to think of
   it is an Internet protocol, with the application JavaScript being
   untrustworthy from the perspective of the JSEP implementation.  Thus,
   the threat model of [RFC3552] applies.  In particular, JavaScript can
   call the API in any order and with any inputs, including malicious
   ones.  This is particularly relevant when we consider the SDP which
   is passed to setLocalDescription().  While correct API usage requires
   that the application pass in SDP which was derived from createOffer()
   or createAnswer(), there is no guarantee that applications do so.
   The JSEP implementation MUST be prepared for the JavaScript to pass
   in bogus data instead.

   Conversely, the application programmer needs to be aware that the
   JavaScript does not have complete control of endpoint behavior.  One
   case that bears particular mention is that editing ICE candidates out
   of the SDP or suppressing trickled candidates does not have the
   expected behavior: implementations will still perform checks from
   those candidates even if they are not sent to the other side.  Thus,
   for instance, it is not possible to prevent the remote peer from
   learning your public IP address by removing server reflexive
   candidates.  Applications which wish to conceal their public IP
   address should instead configure the ICE agent to use only relay
   candidates.

9.  IANA Considerations

   This document requires no actions from IANA.

10.  Acknowledgements

   Harald Alvestrand, Taylor Brandstetter, Suhas Nandakumar, and Peter
   Thatcher provided significant text for this draft.  Bernard Aboba,
   Adam Bergkvist, Dan Burnett, Ben Campbell, Alissa Cooper, Richard
   Ejzak, Stefan Hakansson, Ted Hardie, Christer Holmberg Andrew Hutton,
   Randell Jesup, Matthew Kaufman, Anant Narayanan, Adam Roach, Robert
   Sparks, Neil Stratford, Martin Thomson, Sean Turner, and Magnus
   Westerlund all provided valuable feedback on this proposal.

11.  References

11.1.  Normative References

   [I-D.ietf-avtext-rid]
              Roach, A., Nandakumar, S., and P. Thatcher, "RTP Stream
              Identifier Source Description (SDES)", draft-ietf-avtext-
              rid-09 (work in progress), October 2016.





Uberti, et al.            Expires March 5, 2018                [Page 96]


Internet-Draft                    JSEP                    September 2017


   [I-D.ietf-ice-trickle]
              Ivov, E., Rescorla, E., Uberti, J., and P. Saint-Andre,
              "Trickle ICE: Incremental Provisioning of Candidates for
              the Interactive Connectivity Establishment (ICE)
              Protocol", draft-ietf-ice-trickle-13 (work in progress),
              July 2017.

   [I-D.ietf-mmusic-dtls-sdp]
              Holmberg, C. and R. Shpount, "Session Description Protocol
              (SDP) Offer/Answer Considerations for Datagram Transport
              Layer Security (DTLS) and Transport Layer Security (TLS)",
              draft-ietf-mmusic-dtls-sdp-29 (work in progress), August
              2017.

   [I-D.ietf-mmusic-msid]
              Alvestrand, H., "WebRTC MediaStream Identification in the
              Session Description Protocol", draft-ietf-mmusic-msid-16
              (work in progress), February 2017.

   [I-D.ietf-mmusic-mux-exclusive]
              Holmberg, C., "Indicating Exclusive Support of RTP/RTCP
              Multiplexing using SDP", draft-ietf-mmusic-mux-
              exclusive-12 (work in progress), May 2017.

   [I-D.ietf-mmusic-rid]
              Thatcher, P., Zanaty, M., Nandakumar, S., Burman, B.,
              Roach, A., and B. Campen, "RTP Payload Format
              Restrictions", draft-ietf-mmusic-rid-11 (work in
              progress), July 2017.

   [I-D.ietf-mmusic-sctp-sdp]
              Holmberg, C., Shpount, R., Loreto, S., and G. Camarillo,
              "Session Description Protocol (SDP) Offer/Answer
              Procedures For Stream Control Transmission Protocol (SCTP)
              over Datagram Transport Layer Security (DTLS) Transport.",
              draft-ietf-mmusic-sctp-sdp-26 (work in progress), April
              2017.

   [I-D.ietf-mmusic-sdp-bundle-negotiation]
              Holmberg, C., Alvestrand, H., and C. Jennings,
              "Negotiating Media Multiplexing Using the Session
              Description Protocol (SDP)", draft-ietf-mmusic-sdp-bundle-
              negotiation-39 (work in progress), August 2017.

   [I-D.ietf-mmusic-sdp-mux-attributes]
              Nandakumar, S., "A Framework for SDP Attributes when
              Multiplexing", draft-ietf-mmusic-sdp-mux-attributes-16
              (work in progress), December 2016.



Uberti, et al.            Expires March 5, 2018                [Page 97]


Internet-Draft                    JSEP                    September 2017


   [I-D.ietf-mmusic-sdp-simulcast]
              Burman, B., Westerlund, M., Nandakumar, S., and M. Zanaty,
              "Using Simulcast in SDP and RTP Sessions", draft-ietf-
              mmusic-sdp-simulcast-10 (work in progress), July 2017.

   [I-D.ietf-rtcweb-fec]
              Uberti, J., "WebRTC Forward Error Correction
              Requirements", draft-ietf-rtcweb-fec-06 (work in
              progress), July 2017.

   [I-D.ietf-rtcweb-rtp-usage]
              Perkins, C., Westerlund, M., and J. Ott, "Web Real-Time
              Communication (WebRTC): Media Transport and Use of RTP",
              draft-ietf-rtcweb-rtp-usage-26 (work in progress), March
              2016.

   [I-D.ietf-rtcweb-security]
              Rescorla, E., "Security Considerations for WebRTC", draft-
              ietf-rtcweb-security-08 (work in progress), February 2015.

   [I-D.ietf-rtcweb-security-arch]
              Rescorla, E., "WebRTC Security Architecture", draft-ietf-
              rtcweb-security-arch-12 (work in progress), June 2016.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997, <https://www.rfc-
              editor.org/info/rfc2119>.

   [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
              A., Peterson, J., Sparks, R., Handley, M., and E.
              Schooler, "SIP: Session Initiation Protocol", RFC 3261,
              DOI 10.17487/RFC3261, June 2002, <https://www.rfc-
              editor.org/info/rfc3261>.

   [RFC3264]  Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
              with Session Description Protocol (SDP)", RFC 3264,
              DOI 10.17487/RFC3264, June 2002, <https://www.rfc-
              editor.org/info/rfc3264>.

   [RFC3552]  Rescorla, E. and B. Korver, "Guidelines for Writing RFC
              Text on Security Considerations", BCP 72, RFC 3552,
              DOI 10.17487/RFC3552, July 2003, <https://www.rfc-
              editor.org/info/rfc3552>.







Uberti, et al.            Expires March 5, 2018                [Page 98]


Internet-Draft                    JSEP                    September 2017


   [RFC3605]  Huitema, C., "Real Time Control Protocol (RTCP) attribute
              in Session Description Protocol (SDP)", RFC 3605,
              DOI 10.17487/RFC3605, October 2003, <https://www.rfc-
              editor.org/info/rfc3605>.

   [RFC3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
              Norrman, "The Secure Real-time Transport Protocol (SRTP)",
              RFC 3711, DOI 10.17487/RFC3711, March 2004,
              <https://www.rfc-editor.org/info/rfc3711>.

   [RFC3890]  Westerlund, M., "A Transport Independent Bandwidth
              Modifier for the Session Description Protocol (SDP)",
              RFC 3890, DOI 10.17487/RFC3890, September 2004,
              <https://www.rfc-editor.org/info/rfc3890>.

   [RFC4145]  Yon, D. and G. Camarillo, "TCP-Based Media Transport in
              the Session Description Protocol (SDP)", RFC 4145,
              DOI 10.17487/RFC4145, September 2005, <https://www.rfc-
              editor.org/info/rfc4145>.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, DOI 10.17487/RFC4566,
              July 2006, <https://www.rfc-editor.org/info/rfc4566>.

   [RFC4585]  Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey,
              "Extended RTP Profile for Real-time Transport Control
              Protocol (RTCP)-Based Feedback (RTP/AVPF)", RFC 4585,
              DOI 10.17487/RFC4585, July 2006, <https://www.rfc-
              editor.org/info/rfc4585>.

   [RFC5124]  Ott, J. and E. Carrara, "Extended Secure RTP Profile for
              Real-time Transport Control Protocol (RTCP)-Based Feedback
              (RTP/SAVPF)", RFC 5124, DOI 10.17487/RFC5124, February
              2008, <https://www.rfc-editor.org/info/rfc5124>.

   [RFC5245]  Rosenberg, J., "Interactive Connectivity Establishment
              (ICE): A Protocol for Network Address Translator (NAT)
              Traversal for Offer/Answer Protocols", RFC 5245,
              DOI 10.17487/RFC5245, April 2010, <https://www.rfc-
              editor.org/info/rfc5245>.

   [RFC5285]  Singer, D. and H. Desineni, "A General Mechanism for RTP
              Header Extensions", RFC 5285, DOI 10.17487/RFC5285, July
              2008, <https://www.rfc-editor.org/info/rfc5285>.







Uberti, et al.            Expires March 5, 2018                [Page 99]


Internet-Draft                    JSEP                    September 2017


   [RFC5761]  Perkins, C. and M. Westerlund, "Multiplexing RTP Data and
              Control Packets on a Single Port", RFC 5761,
              DOI 10.17487/RFC5761, April 2010, <https://www.rfc-
              editor.org/info/rfc5761>.

   [RFC5888]  Camarillo, G. and H. Schulzrinne, "The Session Description
              Protocol (SDP) Grouping Framework", RFC 5888,
              DOI 10.17487/RFC5888, June 2010, <https://www.rfc-
              editor.org/info/rfc5888>.

   [RFC6236]  Johansson, I. and K. Jung, "Negotiation of Generic Image
              Attributes in the Session Description Protocol (SDP)",
              RFC 6236, DOI 10.17487/RFC6236, May 2011,
              <https://www.rfc-editor.org/info/rfc6236>.

   [RFC6347]  Rescorla, E. and N. Modadugu, "Datagram Transport Layer
              Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347,
              January 2012, <https://www.rfc-editor.org/info/rfc6347>.

   [RFC6716]  Valin, JM., Vos, K., and T. Terriberry, "Definition of the
              Opus Audio Codec", RFC 6716, DOI 10.17487/RFC6716,
              September 2012, <https://www.rfc-editor.org/info/rfc6716>.

   [RFC6904]  Lennox, J., "Encryption of Header Extensions in the Secure
              Real-time Transport Protocol (SRTP)", RFC 6904,
              DOI 10.17487/RFC6904, April 2013, <https://www.rfc-
              editor.org/info/rfc6904>.

   [RFC7160]  Petit-Huguenin, M. and G. Zorn, Ed., "Support for Multiple
              Clock Rates in an RTP Session", RFC 7160,
              DOI 10.17487/RFC7160, April 2014, <https://www.rfc-
              editor.org/info/rfc7160>.

   [RFC7587]  Spittka, J., Vos, K., and JM. Valin, "RTP Payload Format
              for the Opus Speech and Audio Codec", RFC 7587,
              DOI 10.17487/RFC7587, June 2015, <https://www.rfc-
              editor.org/info/rfc7587>.

   [RFC7742]  Roach, A., "WebRTC Video Processing and Codec
              Requirements", RFC 7742, DOI 10.17487/RFC7742, March 2016,
              <https://www.rfc-editor.org/info/rfc7742>.

   [RFC7850]  Nandakumar, S., "Registering Values of the SDP 'proto'
              Field for Transporting RTP Media over TCP under Various
              RTP Profiles", RFC 7850, DOI 10.17487/RFC7850, April 2016,
              <https://www.rfc-editor.org/info/rfc7850>.





Uberti, et al.            Expires March 5, 2018               [Page 100]


Internet-Draft                    JSEP                    September 2017


   [RFC7874]  Valin, JM. and C. Bran, "WebRTC Audio Codec and Processing
              Requirements", RFC 7874, DOI 10.17487/RFC7874, May 2016,
              <https://www.rfc-editor.org/info/rfc7874>.

   [RFC8108]  Lennox, J., Westerlund, M., Wu, Q., and C. Perkins,
              "Sending Multiple RTP Streams in a Single RTP Session",
              RFC 8108, DOI 10.17487/RFC8108, March 2017,
              <https://www.rfc-editor.org/info/rfc8108>.

   [RFC8122]  Lennox, J. and C. Holmberg, "Connection-Oriented Media
              Transport over the Transport Layer Security (TLS) Protocol
              in the Session Description Protocol (SDP)", RFC 8122,
              DOI 10.17487/RFC8122, March 2017, <https://www.rfc-
              editor.org/info/rfc8122>.

11.2.  Informative References

   [I-D.ietf-mmusic-trickle-ice-sip]
              Ivov, E., Stach, T., Marocco, E., and C. Holmberg, "A
              Session Initiation Protocol (SIP) usage for Trickle ICE",
              draft-ietf-mmusic-trickle-ice-sip-08 (work in progress),
              July 2017.

   [I-D.ietf-rtcweb-ip-handling]
              Uberti, J. and G. Shieh, "WebRTC IP Address Handling
              Requirements", draft-ietf-rtcweb-ip-handling-04 (work in
              progress), July 2017.

   [I-D.ietf-rtcweb-sdp]
              Nandakumar, S. and C. Jennings, "Annotated Example SDP for
              WebRTC", draft-ietf-rtcweb-sdp-06 (work in progress),
              April 2017.

   [RFC3389]  Zopf, R., "Real-time Transport Protocol (RTP) Payload for
              Comfort Noise (CN)", RFC 3389, DOI 10.17487/RFC3389,
              September 2002, <https://www.rfc-editor.org/info/rfc3389>.

   [RFC3556]  Casner, S., "Session Description Protocol (SDP) Bandwidth
              Modifiers for RTP Control Protocol (RTCP) Bandwidth",
              RFC 3556, DOI 10.17487/RFC3556, July 2003,
              <https://www.rfc-editor.org/info/rfc3556>.

   [RFC3960]  Camarillo, G. and H. Schulzrinne, "Early Media and Ringing
              Tone Generation in the Session Initiation Protocol (SIP)",
              RFC 3960, DOI 10.17487/RFC3960, December 2004,
              <https://www.rfc-editor.org/info/rfc3960>.





Uberti, et al.            Expires March 5, 2018               [Page 101]


Internet-Draft                    JSEP                    September 2017


   [RFC4568]  Andreasen, F., Baugher, M., and D. Wing, "Session
              Description Protocol (SDP) Security Descriptions for Media
              Streams", RFC 4568, DOI 10.17487/RFC4568, July 2006,
              <https://www.rfc-editor.org/info/rfc4568>.

   [RFC4588]  Rey, J., Leon, D., Miyazaki, A., Varsa, V., and R.
              Hakenberg, "RTP Retransmission Payload Format", RFC 4588,
              DOI 10.17487/RFC4588, July 2006, <https://www.rfc-
              editor.org/info/rfc4588>.

   [RFC4733]  Schulzrinne, H. and T. Taylor, "RTP Payload for DTMF
              Digits, Telephony Tones, and Telephony Signals", RFC 4733,
              DOI 10.17487/RFC4733, December 2006, <https://www.rfc-
              editor.org/info/rfc4733>.

   [RFC5506]  Johansson, I. and M. Westerlund, "Support for Reduced-Size
              Real-Time Transport Control Protocol (RTCP): Opportunities
              and Consequences", RFC 5506, DOI 10.17487/RFC5506, April
              2009, <https://www.rfc-editor.org/info/rfc5506>.

   [RFC5576]  Lennox, J., Ott, J., and T. Schierl, "Source-Specific
              Media Attributes in the Session Description Protocol
              (SDP)", RFC 5576, DOI 10.17487/RFC5576, June 2009,
              <https://www.rfc-editor.org/info/rfc5576>.

   [RFC5763]  Fischl, J., Tschofenig, H., and E. Rescorla, "Framework
              for Establishing a Secure Real-time Transport Protocol
              (SRTP) Security Context Using Datagram Transport Layer
              Security (DTLS)", RFC 5763, DOI 10.17487/RFC5763, May
              2010, <https://www.rfc-editor.org/info/rfc5763>.

   [RFC5764]  McGrew, D. and E. Rescorla, "Datagram Transport Layer
              Security (DTLS) Extension to Establish Keys for the Secure
              Real-time Transport Protocol (SRTP)", RFC 5764,
              DOI 10.17487/RFC5764, May 2010, <https://www.rfc-
              editor.org/info/rfc5764>.

   [RFC6464]  Lennox, J., Ed., Ivov, E., and E. Marocco, "A Real-time
              Transport Protocol (RTP) Header Extension for Client-to-
              Mixer Audio Level Indication", RFC 6464,
              DOI 10.17487/RFC6464, December 2011, <https://www.rfc-
              editor.org/info/rfc6464>.

   [RFC6544]  Rosenberg, J., Keranen, A., Lowekamp, B., and A. Roach,
              "TCP Candidates with Interactive Connectivity
              Establishment (ICE)", RFC 6544, DOI 10.17487/RFC6544,
              March 2012, <https://www.rfc-editor.org/info/rfc6544>.




Uberti, et al.            Expires March 5, 2018               [Page 102]


Internet-Draft                    JSEP                    September 2017


   [TS26.114]
              3GPP TS 26.114 V12.8.0, "3rd Generation Partnership
              Project; Technical Specification Group Services and System
              Aspects; IP Multimedia Subsystem (IMS); Multimedia
              Telephony; Media handling and interaction (Release 12)",
              December 2014, <http://www.3gpp.org/DynaReport/26114.htm>.

   [W3C.webrtc]
              Bergkvist, A., Burnett, D., Jennings, C., Narayanan, A.,
              Aboba, B., and T. Brandstetter, "WebRTC 1.0: Real-time
              Communication Between Browsers", World Wide Web Consortium
              WD WD-webrtc-20170515, May 2017,
              <https://www.w3.org/TR/2017/WD-webrtc-20170515/>.

Appendix A.  Appendix A

   For the syntax validation performed in Section 5.8, the following
   list of ABNF definitions is used:

































Uberti, et al.            Expires March 5, 2018               [Page 103]


Internet-Draft                    JSEP                    September 2017


   +------------------------+------------------------------------------+
   | Attribute              | Reference                                |
   +------------------------+------------------------------------------+
   | ptime                  | [RFC4566] Section 9                      |
   | maxptime               | [RFC4566] Section 9                      |
   | rtpmap                 | [RFC4566] Section 9                      |
   | recvonly               | [RFC4566] Section 9                      |
   | sendrecv               | [RFC4566] Section 9                      |
   | sendonly               | [RFC4566] Section 9                      |
   | inactive               | [RFC4566] Section 9                      |
   | framerate              | [RFC4566] Section 9                      |
   | fmtp                   | [RFC4566] Section 9                      |
   | quality                | [RFC4566] Section 9                      |
   | rtcp                   | [RFC3605] Section 2.1                    |
   | setup                  | [RFC4145] Sections 3, 4, and 5           |
   | connection             | [RFC4145] Sections 3, 4, and 5           |
   | fingerprint            | [RFC8122] Section 5                      |
   | rtcp-fb                | [RFC4585] Section 4.2                    |
   | candidate              | [RFC5245] Section 15.1                   |
   | remote-candidates      | [RFC5245] Section 15.2                   |
   | ice-lite               | [RFC5245] Section 15.3                   |
   | ice-ufrag              | [RFC5245] Section 15.4                   |
   | ice-pwd                | [RFC5245] Section 15.4                   |
   | ice-options            | [RFC5245] Section 15.5                   |
   | extmap                 | [RFC5285] Section 7                      |
   | mid                    | [RFC5888] Sections 4 and 5               |
   | group                  | [RFC5888] Sections 4 and 5               |
   | imageattr              | [RFC6236] Section 3.1                    |
   | extmap (encrypt        | [RFC6904] Section 4                      |
   | option)                |                                          |
   | msid                   | [I-D.ietf-mmusic-msid] Section 2         |
   | rid                    | [I-D.ietf-mmusic-rid] Section 10         |
   | simulcast              | [I-D.ietf-mmusic-sdp-simulcast] Section  |
   |                        | 6.1                                      |
   | tls-id                 | [I-D.ietf-mmusic-dtls-sdp] Section 4     |
   +------------------------+------------------------------------------+

                       Table 1: SDP ABNF References

Appendix B.  Change log

   Note to RFC Editor: Please remove this section before publication.

   Changes in draft-23:

   o  Clarify rollback handling, and treat it similarly to other
      setLocal/setRemote usages.




Uberti, et al.            Expires March 5, 2018               [Page 104]


Internet-Draft                    JSEP                    September 2017


   o  Adopt a first-fit policy for handling multiple remote a=imageattr
      attributes.

   o  Clarify that a session description with zero m= sections is legal.

   Changes in draft-22:

   o  Clarify currentDirection versus direction.

   o  Correct session-id text so that it aligns with RFC 3264.

   o  Clarify that generated ICE candidate objects must have all four
      fields.

   o  Make rollback work from any state besides stable and regardless of
      whether setLocalDescription or setRemoteDescription is used.

   o  Allow modifying SDP before sending or after receiving either
      offers or answers (previously this was forbidden for answers).

   o  Provide rationale for several design choices.

   Changes in draft-21:

   o  Change dtls-id to tls-id to match MMUSIC draft.

   o  Replace regular expression for proto field with a list and clarify
      that the answer must exactly match the offer.

   o  Remove text about how to error check on setLocal because local
      descriptions cannot be changed.

   o  Rework silence suppression support to always require that both
      sides agree to silence suppression or none is used.

   o  Remove instructions to parse "a=ssrc-group".

   o  Allow the addition of new codecs in answers and in subsequent
      offers.

   o  Clarify imageattr processing.  Replace use of [x=0,y=0] with
      direction indicators.

   o  Document when early media can occur.

   o  Fix ICE default port handling when bundle-only is used.





Uberti, et al.            Expires March 5, 2018               [Page 105]


Internet-Draft                    JSEP                    September 2017


   o  Forbid duplicating IDENTICAL/TRANSPORT attributes when you are
      bundling.

   o  Clarify the number of components to gather when bundle is
      involved.

   o  Explicitly state that PTs and SSRCs are to be used for demuxing.

   o  Update guidance on "a=setup" line.  This should now match the
      MMUSIC draft.

   o  Update guidance on certificate/digest matching to conform to
      RFC8122.

   o  Update examples.

   Changes in draft-20:

   o  Remove Appendix-B.

   Changes in draft-19:

   o  Examples are now machine-generated for correctness, and use IETF-
      approved example IP addresses.

   o  Add early transport warmup example, and add missing attributes to
      existing examples.

   o  Only send "a=rtcp-mux-only" and "a=bundle-only" on new m=
      sections.

   o  Update references.

   o  Add coverage of a=identity.

   o  Explain the lipsync group algorithm more thoroughly.

   o  Remove unnecessary list of MTI specs.

   o  Allow codecs which weren't offered to appear in answers and which
      weren't selected to appear in subsequent offers.

   o  Codec preferences now are applied on both initial and subsequent
      offers and answers.

   o  Clarify a=msid handling for recvonly m= sections.

   o  Clarify behavior of attributes for bundle-only data channels.



Uberti, et al.            Expires March 5, 2018               [Page 106]


Internet-Draft                    JSEP                    September 2017


   o  Allow media attributes to appear in data m= sections when all the
      media m= sections are bundle-only.

   o  Use consistent terminology for JSEP implementations.

   o  Describe how to handle failed API calls.

   o  Some cleanup on routing rules.

   Changes in draft-18:

   o  Update demux algorithm and move it to an appendix in preparation
      for merging it into BUNDLE.

   o  Clarify why we can't handle an incoming offer to send simulcast.

   o  Expand IceCandidate object text.

   o  Further document use of ICE candidate pool.

   o  Document removeTrack.

   o  Update requirements to only accept the last generated offer/answer
      as an argument to setLocalDescription.

   o  Allow round pixels.

   o  Fix code around default timing when AVPF is not specified.

   o  Clean up terminology around m= line and m=section.

   o  Provide a more realistic example for minimum decoder capabilities.

   o  Document behavior when rtcp-mux policy is require but rtcp-mux
      attribute not provided.

   o  Expanded discussion of RtpSender and RtpReceiver.

   o  Add RtpTransceiver.currentDirection and document setDirection.

   o  Require imageattr x=0, y=0 to indicate that there are no valid
      resolutions.

   o  Require a privacy-preserving MID/RID construction.

   o  Require support for RFC 3556 bandwidth modifiers.

   o  Update maxptime description.



Uberti, et al.            Expires March 5, 2018               [Page 107]


Internet-Draft                    JSEP                    September 2017


   o  Note that endpoints may encounter extra codecs in answers and
      subsequent offers from non-JSEP peers.

   o  Update references.

   Changes in draft-17:

   o  Split createOffer and createAnswer sections to clearly indicate
      attributes which always appear and which only appear when not
      bundled into another m= section.

   o  Add descriptions of RtpTransceiver methods.

   o  Describe how to process RTCP feedback attributes.

   o  Clarify transceiver directions and their interaction with 3264.

   o  Describe setCodecPreferences.

   o  Update RTP demux algorithm.  Include RTCP.

   o  Update requirements for when a=rtcp is included, limiting to cases
      where it is needed for backward compatibility.

   o  Clarify SAR handling.

   o  Updated addTrack matching algorithm.

   o  Remove a=ssrc requirements.

   o  Handle a=setup in reoffers.

   o  Discuss how RTX/FEC should be handled.

   o  Discuss how telephone-event should be handled.

   o  Discuss how CN/DTX should be handled.

   o  Add missing references to ABNF table.

   Changes in draft-16:

   o  Update addIceCandidate to indicate ICE generation and allow per-m=
      section end-of-candidates.

   o  Update fingerprint handling to use draft-ietf-mmusic-4572-update.





Uberti, et al.            Expires March 5, 2018               [Page 108]


Internet-Draft                    JSEP                    September 2017


   o  Update text around SDP processing of RTP header extensions and
      payload formats.

   o  Add sections on simulcast, addTransceiver, and createDataChannel.

   o  Clarify text to ensure that the session ID is a positive 63 bit
      integer.

   o  Clarify SDP processing for direction indication.

   o  Describe SDP processing for rtcp-mux-only.

   o  Specify how SDP session version in o= line.

   o  Require that when doing an re-offer, the capabilities of the new
      session are mostly required to be a subset of the previously
      negotiated session.

   o  Clarified ICE restart interaction with bundle-only.

   o  Remove support for changing SDP before calling
      setLocalDescription.

   o  Specify algorithm for demuxing RTP based on MID, PT, and SSRC.

   o  Clarify rules for rejecting m= lines when bundle policy is
      balanced or max-bundle.

   Changes in draft-15:

   o  Clarify text around codecs offered in subsequent transactions to
      refer to what's been negotiated.

   o  Rewrite LS handling text to indicate edge cases and that we're
      living with them.

   o  Require that answerer reject m= lines when there are no codecs in
      common.

   o  Enforce max-bundle on offer processing.

   o  Fix TIAS formula to handle bits vs. kilobits.

   o  Describe addTrack algorithm.

   o  Clean up references.

   Changes in draft-14:



Uberti, et al.            Expires March 5, 2018               [Page 109]


Internet-Draft                    JSEP                    September 2017


   o  Added discussion of RtpTransceivers + RtpSenders + RtpReceivers,
      and how they interact with createOffer/createAnswer.

   o  Removed obsolete OfferToReceiveX options.

   o  Explained how addIceCandidate can be used for end-of-candidates.

   Changes in draft-13:

   o  Clarified which SDP lines can be ignored.

   o  Clarified how to handle various received attributes.

   o  Revised how attributes should be generated for bundled m= lines.

   o  Remove unused references.

   o  Remove text advocating use of unilateral PTs.

   o  Trigger an ICE restart even if the ICE candidate policy is being
      made more strict.

   o  Remove the 'public' ICE candidate policy.

   o  Move open issues into GitHub issues.

   o  Split local/remote description accessors into current/pending.

   o  Clarify a=imageattr handling.

   o  Add more detail on VoiceActivityDetection handling.

   o  Reference draft-shieh-rtcweb-ip-handling.

   o  Make it clear when an ICE restart should occur.

   o  Resolve changes needed in references.

   o  Remove MSID semantics.

   o  ice-options are now at session level.

   o  Default RTCP mux policy is now 'require'.

   Changes in draft-12:

   o  Filled in sections on applying local and remote descriptions.




Uberti, et al.            Expires March 5, 2018               [Page 110]


Internet-Draft                    JSEP                    September 2017


   o  Discussed downscaling and upscaling to fulfill imageattr
      requirements.

   o  Updated what SDP can be modified by the application.

   o  Updated to latest datachannel SDP.

   o  Allowed multiple fingerprint lines.

   o  Switched back to IPv4 for dummy candidates.

   o  Added additional clarity on ICE default candidates.

   Changes in draft-11:

   o  Clarified handling of RTP CNAMEs.

   o  Updated what SDP lines should be processed or ignored.

   o  Specified how a=imageattr should be used.

   Changes in draft-10:

   o  Described video size negotiation with imageattr.

   o  Clarified rejection of sections that do not have mux-only.

   o  Add handling of LS groups

   Changes in draft-09:

   o  Don't return null for {local,remote}Description after close().

   o  Changed TCP/TLS to UDP/DTLS in RTP profile names.

   o  Separate out bundle and mux policy.

   o  Added specific references to FEC mechanisms.

   o  Added canTrickle mechanism.

   o  Added section on subsequent answers and, answer options.

   o  Added text defining set{Local,Remote}Description behavior.

   Changes in draft-08:

   o  Added new example section and removed old examples in appendix.



Uberti, et al.            Expires March 5, 2018               [Page 111]


Internet-Draft                    JSEP                    September 2017


   o  Fixed <proto> field handling.

   o  Added text describing a=rtcp attribute.

   o  Reworked handling of OfferToReceiveAudio and OfferToReceiveVideo
      per discussion at IETF 90.

   o  Reworked trickle ICE handling and its impact on m= and c= lines
      per discussion at interim.

   o  Added max-bundle-and-rtcp-mux policy.

   o  Added description of maxptime handling.

   o  Updated ICE candidate pool default to 0.

   o  Resolved open issues around AppID/receiver-ID.

   o  Reworked and expanded how changes to the ICE configuration are
      handled.

   o  Some reference updates.

   o  Editorial clarification.

   Changes in draft-07:

   o  Expanded discussion of VAD and Opus DTX.

   o  Added a security considerations section.

   o  Rewrote the section on modifying SDP to require implementations to
      clearly indicate whether any given modification is allowed.

   o  Clarified impact of IceRestart on CreateOffer in local-offer
      state.

   o  Guidance on whether attributes should be defined at the media
      level or the session level.

   o  Renamed "default" bundle policy to "balanced".

   o  Removed default ICE candidate pool size and clarify how it works.

   o  Defined a canonical order for assignment of MSTs to m= lines.

   o  Removed discussion of rehydration.




Uberti, et al.            Expires March 5, 2018               [Page 112]


Internet-Draft                    JSEP                    September 2017


   o  Added Eric Rescorla as a draft editor.

   o  Cleaned up references.

   o  Editorial cleanup

   Changes in draft-06:

   o  Reworked handling of m= line recycling.

   o  Added handling of BUNDLE and bundle-only.

   o  Clarified handling of rollback.

   o  Added text describing the ICE Candidate Pool and its behavior.

   o  Allowed OfferToReceiveX to create multiple recvonly m= sections.

   Changes in draft-05:

   o  Fixed several issues identified in the createOffer/Answer sections
      during document review.

   o  Updated references.

   Changes in draft-04:

   o  Filled in sections on createOffer and createAnswer.

   o  Added SDP examples.

   o  Fixed references.

   Changes in draft-03:

   o  Added text describing relationship to W3C specification

   Changes in draft-02:

   o  Converted from nroff

   o  Removed comparisons to old approaches abandoned by the working
      group

   o  Removed stuff that has moved to W3C specification

   o  Align SDP handling with W3C draft




Uberti, et al.            Expires March 5, 2018               [Page 113]


Internet-Draft                    JSEP                    September 2017


   o  Clarified section on forking.

   Changes in draft-01:

   o  Added diagrams for architecture and state machine.

   o  Added sections on forking and rehydration.

   o  Clarified meaning of "pranswer" and "answer".

   o  Reworked how ICE restarts and media directions are controlled.

   o  Added list of parameters that can be changed in a description.

   o  Updated suggested API and examples to match latest thinking.

   o  Suggested API and examples have been moved to an appendix.

   Changes in draft -00:

   o  Migrated from draft-uberti-rtcweb-jsep-02.

Authors' Addresses

   Justin Uberti
   Google
   747 6th St S
   Kirkland, WA  98033
   USA

   Email: justin@uberti.name


   Cullen Jennings
   Cisco
   400 3rd Avenue SW
   Calgary, AB  T2P 4H2
   Canada

   Email: fluffy@iii.ca











Uberti, et al.            Expires March 5, 2018               [Page 114]


Internet-Draft                    JSEP                    September 2017


   Eric Rescorla (editor)
   Mozilla
   331 Evelyn Ave
   Mountain View, CA  94041
   USA

   Email: ekr@rtfm.com












































Uberti, et al.            Expires March 5, 2018               [Page 115]