INTERNET-DRAFT L. Coene(Ed)
Internet Engineering Task Force Siemens
Issued: January 2003 J. Pastor
Expires: July 2003 Ericsson
Telephony Signalling Transport over SCTP applicability statement
< draft-ietf-sigtran-signalling-over-sctp-applic-07.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1ID-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Abstract
This document describes the applicability of the new protocols
developed under the signalling transport framework[RFC2719]. A
description of the main issues regarding the use of the Stream
Control Transmission Protocol (SCTP)[RFC2960] and each adaptation
layer for transport of telephony signalling information over IP
infrastructure is explained.
Coene & Pastor [Page 1]
Draft Telephony signalling over SCTP AS January 2003
Table of contents
Telephony signalling over SCTP Applicability statement ......... ii
Chapter 1: Introduction ........................................ 2
Chapter 1.1: Scope ..... ....................................... 3
Chapter 1.2: Terminology ....................................... 3
Chapter 1.3: Contributors ...................................... 3
Chapter 2: SIGTRAN architecture ................................ 4
Chapter 2.1: Overview ......................................... 4
Chapter 3: Issues for transporting Telephony signalling
information over SCTP .......................................... 6
Chapter 3.1: Congestion control ................................ 6
Chapter 3.2: Detection of failures ............................. 6
Chapter 3.2.1: Retransmission TimeOut (RTO) calculation ........ 7
Chapter 3.2.2: Heartbeat ....................................... 7
Chapter 3.2.3: Maximum Number of retransmissions ............... 7
Chapter 3.3: Shorten end-to-end message delay ................. 7
Chapter 3.4: Bundling considerations ........................... 8
Chapter 3.5: Stream Usage ...................................... 8
Chapter 4: User Adaptation Layers............................... 8
Chapter 4.1: Access Signalling.................................. 11
Chapter 4.1.1: IUA (ISDN Q.921 User Adaptation) ................ 11
Chapter 4.1.2: V5UA (V5.2-User Adaptation) Layer ............... 12
Chapter 4.1.3: DUA (DPNSS/DASS User adaptation) Layer .......... 13
Chapter 4.2: Network Signalling ................................ 13
Chapter 4.2.1: MTP lvl3 over IP ................................ 14
Chapter 4.2.1.1: M2UA (SS7 MTP2-User Adaptation) Layer ......... 14
Chapter 4.2.1.2: M2PA (SS7 MTP2-User Peer-to-Peer Adaptation) .. 15
Chapter 4.2.1.3: Main difference between M2PA and M2UA ......... 16
Chapter 4.2.2: M3UA (SS7 MTP3 User Adaptation) Layer ........... 17
Chapter 4.2.3: SUA (SS7 SCCP User Adaptation) Layer ............ 18
Chapter 5: Security considerations ............................. 20
Chapter 6: References and related work ......................... 20
Chapter 7: Acknowledgments ..................................... 21
Chapter 8: Author's address .................................... 22
1 INTRODUCTION
Coene & Pastor [Page 2]
Draft Telephony signalling over SCTP AS January 2003
This document intends to inform how to transport telephony
signalling protocols, used in classic telephony systems, over IP
networks. The whole architecture is called SIGTRAN (Signalling
Transport) as described in RFC2719 and is composed of a transport
protocol(SCTP) and several User Adaptation layers(UAL). The
transport protocol SCTP has been been developed to fulfill the
stringent requirements that telephony signalling networks have. The
set of User Adaptation layers have also been introduced to make it
possible that different signalling protocols can use the SCTP layer.
1.1 Scope
The scope of this document is to explain the way that user
adaptation layers and SCTP protocols have to be used to transport
Telephony signalling information over IP.
1.2 Terminology
The following terms are commonly identified in related work:
Association: SCTP connection between two endpoints.
Stream: A uni-directional logical channel established within an
association, within which all user messages are delivered in
sequence except for those submitted to the unordered delivery
service.
SPU: Signalling protocol user, the application on top of the User
adaptation layer.
CTSP: Classical Telephony Signalling protocol(examples: MTP level2,
MTP level 3, SCCP....).
UAL: User adaptation layer: the protocol that encapsulate the upper
layer telephony signalling protocols that are to be transported over
SCTP/IP.
ISEP: IP signalling endpoint: a IP node that implements SCTP and a
User adapatation layer.
SP: signalling point
1.3 Contributors
Coene & Pastor [Page 3]
Draft Telephony signalling over SCTP AS January 2003
The following people contributed to the document: L. Coene(Editor),
M. Tuexen, G. Verwimp, J. Loughney, R.R. Stewart, Qiaobing Xie,
M. Holdrege, M.C. Belinchon, A. Jungmaier, J. Pastor and L. Ong.
2 SIGTRAN architecture
The SIGTRAN architecture describes the transport of signalling
information over IP infrastructure.
Telephony Signalling transport over IP normally uses the following
architecture:
Telephony Signalling Application
|
+------------------------------------+
| Signalling Adaptation Layers |
+------------------------------------+
|
+------------------------------------+
|Stream Control Transmission Protocol|
| (SCTP) |
+------------------------------------+
|
Internet Protocol (IPv4/IPv6)
Figure 1.1: Telephony signalling transport protocol stack
The components of the protocol stack are :
(1) Adaptation modules are used when the telephony application needs
to preserve an existing primitive interface. (e.g. management
indications, data operation primitives, ... for a particular
user/application protocol).
(2) SCTP, specially configured to meet the telephony application
performance requirements.
(3) The standard Internet Protocol.
The telephony signalling protocols to be transported can be:
- SS7 MTP3 users: SCCP, ISUP, TUP...
- SS7 MTP2 users: MTP3
- SS7 SCCP users: RANAP, MAP(+TCAP), INAP(+TCAP)...
Coene & Pastor [Page 4]
Draft Telephony signalling over SCTP AS January 2003
- ISDN Q.921 users: Q.931
- V5.2/DSS1
- ....
Every classic telephony protocol can have a corresponding UAL
developed.
The user adaptation layers(UALs) are a set of protocols that
encapsulate a specific signalling protocol to be transported over
SCTP. The adapation is done in a way that the upper signalling
protocols that are relayed remain unaware that the lower layers are
different to the originail lower telephony signalling layers. In
that sense, the upper interface of the user adapatation layers need
to be the same as the upper layer interface to its original lower
layer. If a MTP user is being relayed over the IP network, the
related UAL used to transport the MTP user will have the same upper
interface as MTP has.
The Stream Control Transmission protocol was designed to fulfill the
stringent transport requirements that classical signalling protocols
have and is therefore the recommended transport protocol to use for
this purpose.
The following functions are provided by SCTP:
- Reliable Data Transfer
- Multiple streams to help avoid head-of-line blocking
- Ordered and unordered data delivery on a per-stream basis
- Bundling and fragmentation of user data
- Congestion and flow control
- Support continuous monitoring of reachability
- Graceful termination of association
- Support of multi-homing for added reliability
- Protection against blind denial-of-service attacks
- Protection against blind masquerade attacks
SCTP is used as the transport protocol for telephony signalling
applications. Message boundaries are preserved during data
transport by SCTP and so each UAL can specify its own message
structure withing the SCTP user data. The SCTP user data can be
delivered by the order of transmission within a stream(in sequence
delivery) or unordered.
Coene & Pastor [Page 5]
Draft Telephony signalling over SCTP AS January 2003
SCTP can be used to provide redundancy at the
transport layer and below. Telephony applications needing this level
of redundancy can make use of SCTP's multi-homing support.
SCTP can be used for telephony applications where head-of-line
blocking is a concern. Such an application should use multiple
streams to provide independent ordering of telephony signalling
messages.
3 Issues for transporting telephony signalling over SCTP
Transport of telephony signalling requires special
considerations. In order to use SCTP, special care must be taken to
meet the performance, timing and failure management requirements.
3.1 Congestion Control
The basic mechanism of congestion control in SCTP have been
described in [RFC2960]. SCTP congestion control sometimes conflicts
with the timing requirements of telephony signalling application
messages which are transported by SCTP. During congestion, messages
may be delayed by SCTP, thus sometimes violating the timing
requirements of those telephony applications.
In an engineered network (e.g. a private intranet), in which network
capacity and maximum traffic are very well understood, some
telephony signalling applications may choose to relax the congestion
control rules of SCTP in order to satisfy the timing
requirements. In order to do this, they should employ their own
congestion control mechanisms. But this should be done without
destabilising the network, otherwise this would lead to potential
congestion collapse of the network.
Some telephony signalling applications may have their own congestion
control and flow control techniques. These techniques may interact
with the congestion control procedures in SCTP.
3.2 Detection of failures
Telephony systems often must have no single point of failure in
operation.
The UAL must meet certain service availability and performance
requirements according to the classical signalling layers they are
Coene & Pastor [Page 6]
Draft Telephony signalling over SCTP AS January 2003
replacing. Those requirements may be specific for each UAL.
For example, telephony systems are often required to be able to
preserve stable calls during a component failure. Therefore error
situations at the transport layer and below must be detected quickly
so that the UAL can take approriate steps to recover and preserve the
calls. This poses special requirements on SCTP to discover
unreachablility of a destination address or a peer.
3.2.1 Retransmission TimeOut (RTO) calculation
The SCTP protocol parameter RTO.Min value has a direct impact on the
calculation of the RTO itself. Some telephony applications want to
lower the value of the RTO.Min to less than 1 second. This would
allow the message sender to reach the maximum
number-of-retransmission threshold faster in the case of network
failures. However, lowering RTO.Min may have a negative impact on
network behaviour [ALLMAN99].
In some rare cases, telephony applications might not want to use the
exponential timer back-off concept in RTO calculation in order to
speed up failure detection. The danger of doing this is that, when
network congestion occurs, not backing off the timer may worsen the
congestion situation. Therefore, this strategy should never be used
in public Internet.
It should be noted that not using delayed SACK will also help faster
failure detection.
3.2.2 Heartbeat
For faster detection of (un)availability of idle paths, the
telephony application may consider lowering the SCTP parameter
HB.interval. It should be noted this might result in a higher traffic
load.
3.2.3 Maximum number of retransmissions
Setting Path.Max.Retrans and Association.Max.Retrans SCTP parameters
to lower values will speed up both destination address and peer
failure detection. However, if these values are set too low, the
probability of false fault detections might increase.
Coene & Pastor [Page 7]
Draft Telephony signalling over SCTP AS January 2003
3.3 Shorten end-to-end message delay
Telephony applications often require short end-to-end message
delays. The method described in section 3.2.1 on lowering RTO may
be considered. The different paths within a single association will
have a different RTO, so using the path with the lowest RTO will
lead to a shorter end-to-end message delay for the application
running on top of the UAL's.
3.4 Bundling considerations
Bundling small telephony signalling messages at transmission helps
improve the bandwidth usage efficiency of the network. On the
downside, bundling may introduce additional delay to some of the
messages. This should be taken into consideration when end-to-end
delay is a concern.
3.5 Stream Usage
Telephony signalling traffic is often composed of multiple,
independent message sequences. It is highly desirable to transfer
those independent message sequences in separate SCTP streams. This
reduces the probability of head-of-line blocking in which the
retransmission of a lost message affects the delivery of other
messages not belonging to the same message sequence.
4. User Adaptation Layers
Users Adaptation Layers (UALs) are defined to encapsulate different
signalling protocols in order to transport them over SCTP/IP
There are UALs for both access signalling (DSS1) and trunk signalling
(SS7). A brief description of the standardized UALs follows in the
next sub-sections.
The delivery mechanism in the several UALs
- Supports seamless operation of UALs user peers over an IP
network connection.
- Supports the interface boundary that the UAL user had with the
traditional lower layer.
Coene & Pastor [Page 8]
Draft Telephony signalling over SCTP AS January 2003
- Supports management of SCTP transport associations and traffic
between SGs and ISEPs or two ISEPs
- Supports asynchronous reporting of status changes to management.
Signalling User Adaptation Layers have been developed for both:
Access and Trunk Telephony Signalling. They are defined as follows.
Access Signalling: This is the signalling that is needed between and
access device and an exchange in the core network in order to
establish, manage or release the voice or data call paths. There
are several protocols that have been developed for this purpose.
Trunk Signalling: This is the signalling that is used between the
exchanges inside the core network in order to establish, manage or
release the voice or data call paths. The most common protocols
used for this purpose are known as the SS7 system that belongs to
the Common Channel Signalling (CCS) philosophy. The SS7 protocol
stack is depicted below:
+------+-----+-------+- -+-------+------+-----+------+
| | | | | | MAP | CAP | INAP |
+ | + RANAP |...| BSSAP +-------------------+
| ISUP | TUP | | | | TCAP |
+ | +---------------------------------------+
| | | SCCP |
+----------------------------------------------------+
| MTP3 |
+----------------------------------------------------+
| MTP2 |
+----------------------------------------------------+
| MTP1 |
+----------------------------------------------------+
The Telephony Signalling Protocols to be transported with the already
designed UALS are:
- ISDN Q.921 Users: Q.931
- V5.2/DSS1
- DPNSS/DASS2
- SS7 MTP3 Users: SCCP, ISUP, TUP
- SS7 MTP2 Users: MTP3
- SS7 SCCP Users: TCAP, RANAP, BSSAP, ...
Two main scenarios have been developed to use the different UALS for
IP Signalling Transport:
Coene & Pastor [Page 9]
Draft Telephony signalling over SCTP AS January 2003
(1) Intercommunication of traditional Signalling transport nodes and
IP based nodes.
Traditional Telephony
Telephony Signalling
********* Signalling ********** over IP ********
* SEP *----------------* SG *--------------* ISEP *
********* ********** ********
+-------+ +-------+
|SigProt| |SigProt|
+-------+ +----+----+ +-------+
| | | |UAL | | UAL |
| | | +----+ +-------+
| TTST | |TTST|SCTP| | SCTP |
| | | +----+ +-------+
| | | | IP | | IP |
+-------+ +---------+ +-------+
SEP - Signalling Endpoint
SG - Signalling Gateway
ISEP - IP Signalling Endpoint
SigProt - Signalling Protocol
TTST - Traditional Telephony Signalling Transport
UAL - User Adaptation Layer
SCTP - Stream Control Transport Protocol
It is also referred as SG to AS communication. AS I the name that
UAL usually gives to the ISEP nodes. It stands for Application
Server.
(2) Communication inside the IP network.
Telephony
Signalling
********* over IP *********
* ISEP *------------------* ISEP *
********* *********
+-------+ +-------+
|SigProt| |SigProt|
+-------+ +-------+
| UAL | | UAL |
+-------+ +-------+
| SCTP | | SCTP |
+-------+ +-------+
| IP | | IP |
+-------+ +-------+
This is also referred to as IPSP communication. IPSP is the name
Coene & Pastor [Page 10]
Draft Telephony signalling over SCTP AS January 2003
of the role that an UAL plays on an IP-based node. It stands for
IP Signalling Point.
The first scenario is applied for both types of signalling (access
and trunk signalling). On the other hand the peer to peer basis can
only be used for trunk signalling.
4.1 Access Signalling
The SIGTRAN WG have developed UALs to transport the following Access
Signalling protocols:
- ISDN Q.931
- V5.2
- DPNSS/DASS2
4.1.1 ISDN Q.931 over IP
UAL: IUA (ISDN Q.921 User Adaptation)
This document supports both ISDN Primary Rate Access (PRA) as well as
Basic Rate Access (BRA) including the support for both point-to-point
and point-to-multipoint modes of communication. This support
includes Facility Associated Signalling (FAS), Non-Facility
Associated Signalling (NFAS) and NFAS with backup D channel.
It implements the client/server architecture. The default orientation
would be for the SG to take on the role of server while the ISEP is
the client. The SCTP (and UDP/TCP) Registered User Port Number
Assignment for IUA is 9900.
Examples of the upper layers to be transported would be Q.931 and
QSIG.
The main scenario supported by this UAL is the SG to ISEP
communication where the ISEP role is typically played by a node
called MGC defined in [RFC2719].
****** ISDN ****** IP *******
*PBX *---------------* SG *--------------* MGC *
****** ****** *******
+-----+ +-----+
|Q.931| (NIF) |Q.931|
+-----+ +----------+ +-----+
| | | | IUA| | IUA |
| | | +----+ +-----+
|Q.921| |Q.921|SCTP| |SCTP |
| | | +----+ +-----+
| | | | IP | | IP |
+-----+ +-----+----+ +-----+
Coene & Pastor [Page 11]
Draft Telephony signalling over SCTP AS January 2003
NIF - Nodal Interworking Function
PBX - Private Branch Exchange
SCTP - Stream Control Transmission Protocol
IUA - ISDN User Adaptation Layer Protocol
The SCTP (and UDP/TCP) Registered User Port Number Assignment for IUA
is 9900.
The value assigned by IANA for the Payload Protocol Identifier in the
SCTP Payload Data chunk is ô1ö
4.1.2 V5UA over IP
UAL: V5UA (V5.2-User Adaptation)
It is an extension from the IUA layer with the modifications needed
to support the differences between Q.921 / Q.931, and V5.2 layer 2 /
layer 3. It supports analog telephone access, ISDN basic rate access
and ISDN primary rate access over a V5.2 interface. It is basically
implemented in an interworking scenario with SG.
****** V5.2 ****** IP *******
* AN *---------------* SG *--------------* MGC *
****** ****** *******
+-----+ +-----+
|V5.2 | (NIF) |V5.2 |
+-----+ +----------+ +-----+
| | | |V5UA| |V5UA |
| | | +----+ +-----+
|LAPV5| |LAPV5|SCTP| |SCTP |
| | | +----+ +-----+
| | | | IP + | IP |
+-----+ +-----+----+ +-----+
AN û Access Network
NIF û Nodal Interworking Function
LAPV5 û Link Access Protocol for the V5 channel
SCTP - Stream Control Transmission Protocol
The SCTP (and UDP/TCP) Registered User Port Number Assignment for
V5UA is 5675.
Coene & Pastor [Page 12]
Draft Telephony signalling over SCTP AS January 2003
The value assigned by IANA for the Payload Protocol Identifier in the
SCTP Payload Data chunk is "6".
4.1.3 DPNSS/DASS2 over IP
UAL: DUA (DPNSS/DASS2 User Adaptation)
The DUA is built on top of IUA defining the necessary extensions to
IUA for a DPNSS/DASS2 transport. DPNSS stands for Digital Private
Network Signalling System and DASS2 for Digital Access Signalling
System No 2
****** DPNSS ****** IP *******
*PBX *---------------* SG *--------------* MGC *
****** ****** *******
+-----+ +-----+
|DPNSS| (NIF) |DPNSS|
| L3 | | L3 |
+-----+ +-----+----+ +-----+
| | | | DUA| | DUA |
|DPNSS| |DPNSS+----+ +-----+
| L2 | | L2 |SCTP| |SCTP |
| | | +----+ +-----+
| | | | IP + | IP |
+-----+ +-----+----+ +-----+
PBX - Private Branch eXchange
NIF - Nodal Interworking function
SCTP - Stream Control Transmission Protocol
DUA - DPNSS User Adaptation Layer Protocol
The value assigned by IANA for the Payload Protocol Identifier in the
SCTP Payload Data chunk is "TBD".
4.2 Network Signalling
The SIGTRAN WG have developed UALs to transport the following SS7
protocols:
- MTP2 Users: MTP3
- MTP3 Users: ISUP, TUP, SCCP
- SCCP Users: TCAP, RNSAP, RANAP, BSSAP, ...
4.2.1 MTP lvl3 over IP
Coene & Pastor [Page 13]
Draft Telephony signalling over SCTP AS January 2003
UALs:
- M2UA (SS7 MTP2 User Adaptation)
- M2PA (SS7 MTP2-User Peer-to-Peer Adaptation)
4.2.1.1 M2UA (SS7 MTP2 User Adaptation)
M2UA protocol is mainly used between a Signalling Gateway (SG) and
Media Gateway Controller (MGC). The SG will terminate up to MTP Level
2 and the MGC will terminate MTP Level 3 and above. In other words,
the SG will transport MTP Level 3 messages over an IP network to a
MGC.
The only SS7 MTP2 User is MTP3 that is the protocol transported by
this UAL.
The SG provides a interworking of transport functions with the IP
transport, in order to transfer the MTP2-User signalling messages to
and from an Application Server (e.g. MGC) where the peer MTP2-
User protocol layer exists.
****** SS7 ****** IP *******
*SEP *-----------* SG *-------------* MGC *
****** ****** *******
+----+ +----+
|S7UP| |S7UP|
+----+ +----+
|MTP3| |MTP3|
| | (NIF) | |
+----+ +----+----+ +----+
| | | |M2UA| |M2UA|
| | | +----+ +----+
|MTP2| |MTP2|SCTP| |SCTP|
| | | +----+ +----+
| | | |IP | |IP |
+----+ +---------+ +----+
MGC - Media Gateway Controler
SG - Signalling Gateway
SEP - SS7 Signalling Endpoint
NIF - Nodal Interworking Function
IP - Internet Protocol
SCTP - Stream Control Transmission Protocol
The SCTP (and UDP/TCP) Registered User Port Number Assignment for
M2UA is 2904.
Coene & Pastor [Page 14]
Draft Telephony signalling over SCTP AS January 2003
The value assigned by IANA for the Payload Protocol Identifier in the
SCTP Payload Data chunk is "2"
4.2.1.2 M2PA (SS7 MTP2-User Peer-to-Peer Adaptation) Layer
M2PA protocol is used between SS7 Signalling Points employing the MTP
Level 3 protocol. The SS7 Signalling Points may also employ standard
SS7 links using the SS7 MTP Layer 2 to provide transport of MTP Layer
3 signalling messages.
Both configurations: intercommunication of SS7 and IP with SG and
communication between ISEPs are possible.
Communication between two IP nodes:
******** IP ********
* IPSP *--------* IPSP *
******** ********
+------+ +------+
| TCAP | | TCAP |
+------+ +------+
| SCCP | | SCCP |
+------+ +------+
| MTP3 | | MTP3 |
+------+ +------+
| M2PA | | M2PA |
+------+ +------+
| SCTP | | SCTP |
+------+ +------+
| IP | | IP |
+------+ +------+
IP - Internet Protocol
IPSP - IP Signalling Point
SCTP - Stream Control Transmission Protocol
Interconnection of SS7 and IP nodes:
Coene & Pastor [Page 15]
Draft Telephony signalling over SCTP AS January 2003
******** SS7 *************** IP ********
* SEP *--------* SG *--------* IPSP *
******** *************** ********
+------+ +------+
| TCAP | | TCAP |
+------+ +------+
| SCCP | | SCCP |
+------+ +-------------+ +------+
| MTP3 | | MTP3 | | MTP3 |
+------+ +------+------+ +------+
| | | | M2PA | | M2PA |
| | | +------+ +------+
| MTP2 | | MTP2 | SCTP | | SCTP |
| | | +------+ +------+
| | | | IP | | IP |
+------+ +------+------+ +------+
SEP - SS7 Signalling Endpoint
These figures are only an example. Other configurations are possible.
For example, IPSPs without traditional SS7 links could use the
protocol layers MTP3/M2PA/SCTP/IP to route SS7 messages in a network
with all IP links.
Another example is that two SGs could be connected over an IP network
to form an SG mated pair similar to the way STPs are provisioned in
traditional SS7 networks.
The SCTP (and UDP/TCP) Registered User Port Number Assignment for
M2PA is TBD.
The value assigned by IANA for the Payload Protocol Identifier in the
SCTP Payload Data chunk is TBD
4.2.1.3 Main differences between M2PA and M2UA:
a. M2PA: IPSP processes MTP3/MTP2 primitives.
M2UA: MGC transports MTP3/MTP2 primitives between the SG's MTP2
and the MGC's MTP3 (via the NIF) for processing.
b. M2PA: SG-IPSP connection is an SS7 link.
M2UA: SG-MGC connection is not an SS7 link. It is an
extension of MTP to a remote entity.
c. M2PA: SG is an SS7 node with a point code.
M2UA: SG is not an SS7 node and has no point code.
d. M2PA: SG can have upper SS7 layers, e.g., SCCP.
M2UA: SG does not have upper SS7 layers since it has no MTP3.
Coene & Pastor [Page 16]
Draft Telephony signalling over SCTP AS January 2003
e. M2PA: relies on MTP3 for management procedures.
M2UA: uses M2UA management procedures.
4.3 MTP lvl3-Users (ISUP, TUP, SCCP) over IP
UAL: M3UA (SS7 MTP3 User Adaptation)
M3UA protocol supports the transport of any SS7 MTP3-User signalling
such as TUP, ISUP and SCCP over IP using the services of SCTP.
Interconnection of SS7 and IP nodes:
******** SS7 ***************** IP ********
* SEP *---------* SGP *--------* ASP *
******** ***************** ********
+------+ +---------------+ +------+
| ISUP | | (NIF) | | ISUP |
+------+ +------+ +------+ +------+
| MTP3 | | MTP3 | | M3UA | | M3UA |
+------| +------+-+------+ +------+
| MTP2 | | MTP2 | | SCTP | | SCTP |
+------+ +------+ +------+ +------+
| L1 | | L1 | | IP | | IP |
+------+ +------+ +------+ +------+
SEP - SS7 Signalling End Point
SCTP - Stream Control Transmission Protocol
NIF - Nodal Interworking Function
Communication between two IP nodes:
Coene & Pastor [Page 17]
Draft Telephony signalling over SCTP AS January 2003
******** IP ********
* IPSP *----------* IPSP *
******** ********
+------+ +------+
|SCCP- | |SCCP- |
| User | | User |
+------+ +------+
| SCCP | | SCCP |
+------+ +------+
| M3UA | | M3UA |
+------+ +------+
| SCTP | | SCTP |
+------+ +------+
| IP | | IP |
+------+ +------+
It works using the client-server philosophy. ISEP is recommended to
be client when talking with a SG. The reserved port by IANA is 2905
to listen to possible client connections.
The assigned payload protocol identifier for the SCTP DATA chunks is
ô3ö.
4.4 SCCP-Users over IP
UAL: SUA (SS7 SCCP User Adaptation)
SUA protocol supports the transport of any SS7 SCCP-User signalling
such as MAP, INAP, SMS, BSSAP, RANAP over IP using the services of
SCTP. SUA can support only non-call related signalling.
SUA does not pose stringent timing constraints on SCTP due to the
fact that SUA applications have broad timing requirement (from 10 of
seconds to hours) which the applications guard themselves and the
timing supervision of the application is end-to-end, not hop-by-
hop(as with ISUP).
Possible configurations are showed in the pictures below.
- Interconnection of SS7 and IP:
Coene & Pastor [Page 18]
Draft Telephony signalling over SCTP AS January 2003
******** *************** ********
* SEP * IP * * IP * *
* or *---------* SG *--------* ASP *
* STP * * * * *
******** *************** ********
+------ +------+
| SUAP | | SUAP |
+------+ +------+------+ +------+
| SCCP | | SCCP | SUA | | SUA |
+------+ +------+------+ +------+
| | | | | | |
| MTP3 | | MTP3 | SCTP | | SCTP |
| | | | | | |
+------+ +------+------+ +------+
| MTP2 | | MTP2 | IP | | IP |
+------+ +------+------+ +------+
SUAP - SCCP/SUA User Protocol (TCAP, for example)
STP - SS7 Signalling Transfer Point
- IP Node to IP Node communication:
******** ********
* * IP * *
* IPSP *--------* IPSP *
* * * *
******** ********
+------+ +------+
| SUAP | | SUAP |
+------+ +------+
| SUA | | SUA |
+------+ +------+
| SCTP | | SCTP |
+------+ +------+
| IP | | IP |
+------+ +------+
IANA has registered SCTP Port Number 14001 for SUA. It is
recommended that SGs use this SCTP port number for listening for new
connections. The payload protocol identifier for the SCTP DATA chunks
is "4".
Coene & Pastor [Page 19]
Draft Telephony signalling over SCTP AS January 2003
5 Security considerations
UALs are designated to carry signalling messages for telephony
services. As such, UALs must involve the security needs of several
parties: the end users of the services; the network providers and
the applications involved. Additional requirements may come from
local regulation. While having some overlapping security needs, any
security solution should fulfill all of the different parties'
needs. See specific Security considerations in each UAL technical
specification.
SCTP only tries to increase the availability of a network. SCTP does
not contain any protocol mechanisms which are directly related to
communication security, i.e. user message authentication, integrity
or confidentiality functions. For such features, it depends on
security protocols. In the field of system security, SCTP includes
mechanisms for reducing the risk of blind denial-of-service attacks
as it is described in section 11 in RFC2960.
This document does not add any new components to the protocols
included in the discussion. For secure use of the SIGTRAN protocols
the readers should go through the "Security Considerations for
SIGTRAN protocols" [RFCSIGSEC]). According to that document, the use
of the IPsec is the main recommendation to secure SIGTRAN protocols
in the Internet, but TLS is also considered as a perfectly valid
option to be used in certain scenarios. Recomendations of usage are
also included.
6 References and related work
[RFC2960] Stewart, R. R., Xie, Q., Morneault, K., Sharp, C. , ,
Schwarzbauer, H. J., Taylor, T., Rytina, I., Kalla, M., Zhang,
L. and Paxson, V, "Stream Control Transmission Protocol", RFC2960,
October 2000.
[RF3257] Coene, L., Tuexen, M., Verwimp, G., Loughney, J., Stewart,
R. R., Xie, Q., Holdrege, M., Belinchon, M.C., and Jungmayer, A.,
"Stream Control Transmission Protocol Applicability statement",
RFC3257, April 2002.
[RFC2719] Ong, L., Rytina, I., Garcia, M., Schwarzbauer, H., Coene,
L., Lin, H., Juhasz, I., Holdrege, M., Sharp, C., "Framework
Architecture for Signalling Transport", RFC2719, October 1999.
Coene & Pastor [Page 20]
Draft Telephony signalling over SCTP AS January 2003
[RFC3057] Morneault, K., Rengasami, S., Kalla, M., Sidebottom, G.,
"ISDN Q.921-User Adaptation Layer", RFC3057, February 2001.
[RFC3331] Morneault, K., Dantu, R., Sidebottom, G., George, T.,
Bidulock, B., Heitz , J., "Signaling System 7 (SS7) Message Transfer
Part (MTP) 2 - User Adaptation Layer", RFC3331, September 2002.
[RFC3332] Sidebottom, G., Pastor-Balbas, J., Rytina, I., Mousseau,
G., Ong, L., Schwarzbauer, H.J., Gradischnig, K., Morneault, K.,
Kalla, M., Glaude, N., Bidulock, B., Loughney, J., "SS7 MTP3-User
Adaptation Layer (M3UA)", RFC3332, September 2002.
[RFCzzzz] Loughney, J., Sidebottom, G., Mousseau, G., Lorusso, S.,
Coene, L., Verwimp, G., Keller, J., Escobar, F., Sully, W., Furniss,
S., Bidulock, B.,"SS7 SCCP-User Adaptation Layer (SUA)", RFCzzzz,
May 2002.
[RFCwwww] George, T., Dantu, R., Kalla, M., Schwarzbauer, H.J.,
Sidebottom, G., Morneault, K.,"SS7 MTP2-User Peer-to-Peer Adaptation
Layer", RFCwwww, June 2002.
[RFCqqqq] Weilandt, E., Khanchandani, N., Rao, S.,"V5.2-User
Adaptation Layer (V5UA)", RFCqqqq, June 2002
[RFCtttt] Vydyam, A., Mukundan, R., Mangalpally, N., Morneault,
K.,"DPNSS/DASS 2 extensions to the IUA protocol", RFCtttt, August
2002.
[ALLMAN99] Allman, M. and Paxson, V., "On Estimating End-to-End
Network Path Properties", Proc. SIGCOMM'99, 1999.
[RFCSIGSEC] Loughney, J., Tuexen, M. and Pastor-Balbas, J.,"Security
Considerations for SIGTRAN Protocols",
draft-ietf-sigtran-security-00.txt, work in progress
7 Acknowledgments
This document was initially developed by a design team consisting of
Lode Coene, John Loughney, Michel Tuexen, Randall R. Stewart,
Qiaobing Xie, Matt Holdrege, Maria-Carmen Belinchon, Andreas
Jungmaier, Gery Verwimp and Lyndon Ong.
Coene & Pastor [Page 21]
Draft Telephony signalling over SCTP AS January 2003
The authors wish to thank Renee Revis, H.J. Schwarzbauer, T. Taylor,
G. Sidebottom, K. Morneault, T. George, M. Stillman and many others
for their invaluable comments.
8 Author's Address
Lode Coene Phone: +32-14-252081
Siemens Atea EMail: lode.coene@siemens.com
Atealaan 34
B-2200 Herentals
Belgium
Javier Pastor-Balbas Phone: +34-91-3393819
Ericsson Espana S.A. Email: j.javier.pastor@ericsson.com-
C/ Retama 1
28045 Madrid
Spain
Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished
to others, and derivative works that comment on or otherwise
explain it or assist in its implementation may be prepared,
copied, published and distributed, in whole or in part, without
restriction of any kind, provided that the above copyright notice
and this paragraph are included on all such copies and derivative
works. However, this document itself may not be modified in any
way, such as by removing the copyright notice or references to the
Internet Society or other Internet organizations, except as needed
for the purpose of developing Internet standards in which case the
procedures for copyrights defined in the Internet Standards
process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not
be revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on
an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
Coene & Pastor [Page 22]
Draft Telephony signalling over SCTP AS January 2003
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
-
Coene & Pastor [Page 23]