SIP M. Munakata
Internet-Draft S. Schubert
Intended status: Informational T. Ohba
Expires: October 7, 2009 NTT
April 05, 2009
UA-Driven Privacy Mechanism for SIP
draft-ietf-sip-ua-privacy-07
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on October 7, 2009.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Abstract
This document defines a guideline for a User Agent (UA) to generate
an anonymous Session Initiation Protocol (SIP) message by utilizing
Munakata, et al. Expires October 7, 2009 [Page 1]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
mechanisms such as Globally Routable User Agent URIs (GRUU) and
Traversal Using Relays around NAT (TURN) without the need for a
privacy service defined in RFC 3323.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Concept of Privacy . . . . . . . . . . . . . . . . . . . . . . 4
4. Treatment of Privacy-Sensitive Information . . . . . . . . . . 4
4.1. Obtaining a Functional Anonymous URI Using the GRUU
Mechanism . . . . . . . . . . . . . . . . . . . . . . . . 4
4.2. Obtaining a Functional Anonymous IP Address Using the
TURN Mechanism . . . . . . . . . . . . . . . . . . . . . . 5
5. UA Behavior . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.1. Critical Privacy-Sensitive Information . . . . . . . . . . 6
5.1.1. Contact Header Field . . . . . . . . . . . . . . . . . 6
5.1.2. From Header Field in requests . . . . . . . . . . . . 7
5.1.3. Via Header Field in requests . . . . . . . . . . . . . 8
5.1.4. IP Addresses in SDP . . . . . . . . . . . . . . . . . 8
5.2. Non-Critical Privacy-Sensitive Information . . . . . . . . 8
5.2.1. Host Names in Other SIP Header Fields . . . . . . . . 8
5.2.2. Optional SIP Header Fields . . . . . . . . . . . . . . 8
6. Security Considerations . . . . . . . . . . . . . . . . . . . 9
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1. Normative References . . . . . . . . . . . . . . . . . . . 10
8.2. Informative References . . . . . . . . . . . . . . . . . . 10
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 11
Munakata, et al. Expires October 7, 2009 [Page 2]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
1. Introduction
[RFC3323] defines a privacy mechanism for the Session Initiation
Protocol (SIP)[RFC3261], based on techniques available at the time of
its publication. This mechanism relies on the use of a separate
privacy service to remove privacy-sensitive information from SIP
messages sent by a User Agent (UA) before forwarding those messages
to the final destination. Since then, numerous SIP extensions have
been proposed and standardized. Some of those enable a UA to
withhold its user's identity and related information without the need
for privacy services, which was not possible when RFC 3323 was
defined.
The purpose of this document is not to obsolete RFC 3323, but to
enhance the overall privacy mechanism in SIP by allowing a UA to take
control of its privacy, rather than being completely dependent on an
external privacy service.
The UA-driven privacy mechanism defined in this document will not
eliminate the need for the RFC 3323 usage defined in [RFC3325], which
instructs a privacy service not to forward a P-Asserted-Identity
header field outside the Trust Domain. In order to prevent
forwarding a P-Asserted-Identity header field outside the Trust
Domain, a UA needs to include the Privacy header field with value
'id' (Privacy:id) in the request, even when the UA is utilizing this
specification.
This document defines a guideline in which a UA controls all the
privacy functions on its own utilizing SIP extensions such as
Globally Routable User Agent URIs (GRUU) [I-D.ietf-sip-gruu] and
Traversal Using Relays around NAT (TURN) [I-D.ietf-behave-turn].
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
privacy-sensitive information:
The information that identifies a user who sends the SIP
message, as well as other information that can be used to
guess the user's identity.
Munakata, et al. Expires October 7, 2009 [Page 3]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
3. Concept of Privacy
The concept of privacy in this document is the act of concealing
privacy-sensitive information. The protection of network privacy
(e.g., topology hiding) is outside the scope for this document.
Privacy-sensitive information includes display-name and Uniform
Resource Identifier (URI) in a From header field that can reveal the
user's name and affiliation (e.g., company name), and IP addresses or
host names in a Contact header field, a Via header field, a Call-ID
header field, or a Session Description Protocol (SDP) [RFC4566] body
that might reveal the location of a UA.
4. Treatment of Privacy-Sensitive Information
Some fields of a SIP message potentially contain privacy-sensitive
information but are not essential for achieving the intended purpose
of the message and can be omitted without any side effects. Other
fields are essential for achieving the intended purpose of the
message and need to contain anonymized values in order to avoid
disclosing privacy-sensitive information. Of the privacy-sensitive
information listed in section 3, URIs, host names, and IP addresses
in Contact, Via, and SDP are required to be functional (i.e.,
suitable for purpose) even when they are anonymized.
With the use of GRUU [I-D.ietf-sip-gruu] and TURN
[I-D.ietf-behave-turn], a UA can obtain URIs and IP addresses for
media and signaling that are functional yet anonymous, and do not
identify either the UA or the user. Instructions on how to obtain a
functional anonymous URI and IP address are given in Section 4.1 and
4.2, respectively.
Host names need to be concealed because the user's identity can be
guessed from them, but they are not always regarded as critical
privacy-sensitive information.
In addition, a UA needs to be careful not to include any information
that identifies the user in optional SIP header fields such as
Subject and User-Agent.
4.1. Obtaining a Functional Anonymous URI Using the GRUU Mechanism
A UA wanting to obtain a functional anonymous URI MUST support and
utilize the GRUU mechanism unless it is able to obtain a functional
anonymous URI through other means outside the scope for this
document. By sending a REGISTER request requesting GRUU, the UA can
obtain an anonymous URI, which can later be used for the Contact
Munakata, et al. Expires October 7, 2009 [Page 4]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
header field.
The detailed process on how a UA obtains a GRUU is described in
[I-D.ietf-sip-gruu].
In order to use the GRUU mechanism to obtain a functional anonymous
URI, the UA MUST request GRUU in the REGISTER request. If a "temp-
gruu" SIP URI parameter and value are present in the REGISTER
response, the user agent MUST use the value of the "temp-gruu" as an
anonymous URI representing the UA. This means that the UA MUST use
this URI as its local target and that the UA MUST place this URI in
the Contact header field of subsequent requests and responses that
require the local target to be sent.
If there is no "temp-gruu" SIP URI parameter in the 200 (OK) response
to the REGISTER request, a UA SHOULD NOT proceed with its
anonymization process, unless something equivalent to "temp-gruu" is
provided through some administrative means.
It is RECOMMENDED that UA consult the user before sending a request
without a functional anonymous URI when privacy is requested from the
user.
Due to the nature of how GRUU works, the domain name is always
revealed when GRUU is used. If revealing the domain name in the
Contact header field is a concern, use of a third party GRUU server
is a possible solution, but this is outside the scope of this
document. Refer to the Security Considerations section for details.
4.2. Obtaining a Functional Anonymous IP Address Using the TURN
Mechanism
A UA that is not provided with a functional anonymous IP address
through some administrative means MUST obtain a relayed address (IP
address of a relay) if anonymity is desired for use in SDP and in the
Via header field. Such an IP address is to be derived from a Session
Traversal Utilities of NAT (STUN) relay server through the TURN
mechanism, which allows a STUN server to act as a relay.
Anonymous IP addresses are needed for two purposes. The first is for
use in the Via header field of a SIP request. By obtaining an IP
address from a STUN relay server, using that address in the Via
header field of the SIP request, and sending the SIP request to the
STUN relay server, the IP address of the UA will not be revealed
beyond the relay server.
The second is for use in SDP as an address for receiving media. By
obtaining an IP address from a STUN relay server and using that
Munakata, et al. Expires October 7, 2009 [Page 5]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
address in SDP, media will be received via the relay server. Also
media can be sent via the relay server. In this way, neither SDP nor
media packets reveal the IP address of the UA.
It is assumed that a UA is either manually or automatically
configured through means such as the configuration framework
[I-D.ietf-sipping-config-framework] with the address of one or more
STUN (Session Traversal Utilities for NAT) [I-D.ietf-behave-turn]
relay servers to obtain anonymous IP address.
5. UA Behavior
This section describes how to generate an anonymous SIP message at a
UA.
A UA fully compliant with this document MUST obscure or conceal all
the critical UA-inserted privacy-sensitive information in SIP
requests and responses as shown in Section 5.1 when user privacy is
requested. In addition, the UA SHOULD conceal the non-critical
privacy-sensitive information as shown in Section 5.2.
Furthermore, when a UA uses a relay server to conceal its identity,
the UA MUST send requests to the relay server to ensure request and
response follow the same signaling path.
5.1. Critical Privacy-Sensitive Information
5.1.1. Contact Header Field
When using this header field in a dialog-forming request or response
or in a mid-dialog request or response, this field contains the local
target, i.e., a URI used to reach the UA for mid-dialog requests and
possibly out-of-dialog requests, such as a REFER request[RFC3515].
The Contact header field can also contain a display-name. Since the
Contact header field is used for routing further requests to the UA,
the UA MUST include a functional URI even when it is anonymized.
When using this header field in a dialog-forming request or response
or in a mid-dialog request or response, the UA MUST anonymize the
Contact header field using an anonymous URI ("temp-gruu") obtained
through the GRUU mechanism, unless an equivalent functional anonymous
URI is provided by some other means. For other requests and
responses, with the exception of 3xx responses, REGISTER requests and
200 (OK) responses to a REGISTER request, the UA MUST either omit the
Contact header field or use an anonymous URI.
Refer to Section 4.1 for details on how to obtain an anonymous URI
Munakata, et al. Expires October 7, 2009 [Page 6]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
through GRUU.
The UA MUST omit the display-name in a Contact header field or set
the display-name to "Anonymous".
5.1.2. From Header Field in requests
Without privacy considerations, this field contains the identity of
the user, such as display-name and URI.
RFCs 3261 and 3323 recommend to set "sip:anonymous@anonymous.invalid"
as a SIP URI in a From header field when user privacy is requested.
This raises an issue when the SIP-Identity mechanism [RFC4474] is
applied to the message, because SIP-Identity requires an actual
domain name in the From header field.
A UA generating an anonymous SIP message supporting this
specification MUST anonymize the From header field in one of the two
ways described below.
Option 1:
A UA anonymizes a From header field using an anonymous display-name
and an anonymous URI following the procedure noted in section 4.1.1.3
of RFC 3323.
The example form of the From header field of option 1 is as follows:
From: "Anonymous" <sip:anonymous@anonymous.invalid>;tag=1928301774
Option 2:
A UA anonymizes a From header field using an anonymous display-name
and an anonymous URI with user's valid domain name instead of
"anonymous.invalid".
The example form of the From header field of option 2 is as follows:
From: "Anonymous" <sip:anonymous@atlanta.com>;tag=1928301774
A UA SHOULD go with option 1 to conceal its domain name in the From
header field. However, SIP-Identity cannot be used with a From
header field in accordance with option 1, because the SIP-Identity
mechanism uses authentication based on the domain name.
If a UA expects the SIP-Identity mechanism to be applied to the
request, it is RECOMMENDED to go with option 2. However, the user's
domain name will be revealed from the From header field of option 2.
Munakata, et al. Expires October 7, 2009 [Page 7]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
If the user wants both anonymity and strong identity, a solution
would be to use a third party anonymization service that issues an
Address of Record (AoR) for use in the From header field of a request
and that also provides a SIP-Identity Authentication Service.Third
party anonymization service is out of scope for this document.
5.1.3. Via Header Field in requests
Without privacy considerations, the bottommost Via header field added
to a request by a UA contains the IP address and port or hostname
that are used to reach the UA for responses.
A UA generating an anonymous SIP request supporting this
specification MUST anonymize the IP address in the Via header field
using an anonymous IP address obtained through the TURN mechanism,
unless an equivalent functional anonymous IP address is provided by
some other means.
The UA SHOULD NOT include a host name in a Via header field .
5.1.4. IP Addresses in SDP
A UA generating an anonymous SIP message supporting this
specification MUST anonymize IP addresses in SDP, if present, using
an anonymous IP address obtained through the TURN mechanism, unless
an equivalent functional anonymous IP address is provided by some
other means.
Refer to Section 4.2 for details on how to obtain an IP address
through TURN.
5.2. Non-Critical Privacy-Sensitive Information
5.2.1. Host Names in Other SIP Header Fields
A UA generating an anonymous SIP message supporting this
specification SHOULD conceal host names in any SIP header fields,
such as Call-ID and Warning header fields, if considered privacy-
sensitive.
5.2.2. Optional SIP Header Fields
Other optional SIP header fields (such as Call-Info, In-Reply-To,
Organization, Referred-By, Reply-To, Server, Subject, User-Agent, and
Warning) can contain privacy-sensitive information.
A UA generating an anonymous SIP message supporting this
specification SHOULD NOT include any information that identifies the
Munakata, et al. Expires October 7, 2009 [Page 8]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
user in such optional header fields.
6. Security Considerations
This specification uses GRUU and TURN and inherits any security
considerations described in these drafts.
Furthermore, if the provider of the caller intending to obscure its
identity consists of a small number of people (e.g. small enterprise,
SOHO), the domain name alone can reveal the identity of the caller.
The same can be true when the provider is large but the receiver of
the call only knows a few people from the source of call.
There are mainly two places in the message, From header field and
Contact header field, where the domain name is expected to be
functional.
The domain name in the From header field can be obscured as described
in section 5.1.2, whereas the Contact header field needs to contain a
valid domain name at all times in order to function properly.
Note: Generally a device will not show the contact address to the
receiver, but this does not mean that one can not find the domain
name in a message. In fact as long as this specification is used to
obscure identity, the message will always contain a valid domain name
as it inherits key characteristics of GRUU.
Note: For UAs that use a temporary GRUU confidentiality does not
extend to parties that are permitted to register to the same AoR or
are permitted to obtain temporary GRUUs when subscribed to the 'reg'
event package [RFC3680] for the AoR. To limit this, it is suggested
that the authorization policy for the 'reg' event package permit only
those subscribers authorized to register to the AoR to receive
temporary GRUUs. With this policy, the confidentiality of the
temporary GRUU will be the same whether or not the 'reg' event
package is used.
If one wants to assure anonymization, it is suggested for the user to
seek and rely on a third party anonymization service, which is
outside the scope of this document.
A third party anonymization service provides registrar and TURN
service that have no affiliation with the caller's provider, allowing
caller to completely withhold its identity.
Munakata, et al. Expires October 7, 2009 [Page 9]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
7. IANA Considerations
This document requires no action by IANA.
8. References
8.1. Normative References
[I-D.ietf-behave-turn]
Rosenberg, J., Mahy, R., and P. Matthews, "Traversal Using
Relays around NAT (TURN): Relay Extensions to Session
Traversal Utilities for NAT (STUN)",
draft-ietf-behave-turn-13 (work in progress),
February 2009.
[I-D.ietf-sip-gruu]
Rosenberg, J., "Obtaining and Using Globally Routable User
Agent (UA) URIs (GRUU) in the Session Initiation Protocol
(SIP)", draft-ietf-sip-gruu-15 (work in progress),
October 2007.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
Description Protocol", RFC 4566, July 2006.
8.2. Informative References
[I-D.ietf-sipping-config-framework]
Channabasappa, S., "A Framework for Session Initiation
Protocol User Agent Profile Delivery",
draft-ietf-sipping-config-framework-15 (work in progress),
February 2008.
[RFC3323] Peterson, J., "A Privacy Mechanism for the Session
Initiation Protocol (SIP)", RFC 3323, November 2002.
[RFC3325] Jennings, C., Peterson, J., and M. Watson, "Private
Extensions to the Session Initiation Protocol (SIP) for
Asserted Identity within Trusted Networks", RFC 3325,
November 2002.
Munakata, et al. Expires October 7, 2009 [Page 10]
Internet-Draft UA-Driven Privacy Mechanism for SIP April 2009
[RFC3515] Sparks, R., "The Session Initiation Protocol (SIP) Refer
Method", RFC 3515, April 2003.
[RFC3680] Rosenberg, J., "A Session Initiation Protocol (SIP) Event
Package for Registrations", RFC 3680, March 2004.
[RFC4474] Peterson, J. and C. Jennings, "Enhancements for
Authenticated Identity Management in the Session
Initiation Protocol (SIP)", RFC 4474, August 2006.
Authors' Addresses
Mayumi Munakata
NTT Corporation
Email: munakata.mayumi@lab.ntt.co.jp
Shida Schubert
NTT Corporation
Email: shida@ntt-at.com
Takumi Ohba
NTT Corporation
9-11, Midori-cho 3-Chome
Musashino-shi, Tokyo 180-8585
Japan
Phone: +81 422 59 7748
Email: ohba.takumi@lab.ntt.co.jp
URI: http://www.ntt.co.jp
Munakata, et al. Expires October 7, 2009 [Page 11]