SIPPING WG A. Pendleton
Internet-Draft A. Clark
Intended status: Standards Track Telchemy Incorporated
Expires: September 6, 2010 A. Johnston
Avaya
H. Sinnreich
Unaffiliated
March 5, 2010
Session Initiation Protocol Event Package for Voice Quality Reporting
draft-ietf-sipping-rtcp-summary-09
Abstract
This document defines a Session Initiation Protocol (SIP) event
package that enables the collection and reporting of metrics that
measure the quality for Voice over Internet Protocol (VoIP) sessions.
Voice call quality information derived from RTP Control Protocol
Extended Reports (RTCP-XR) and call information from SIP is conveyed
from a User Agent (UA) in a session, known as a reporter, to a third
party, known as a collector. A registration for the application/
vq-rtcp-xr MIME type is also included.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on September 6, 2010.
Copyright Notice
Pendleton, et al. Expires September 6, 2010 [Page 1]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Pendleton, et al. Expires September 6, 2010 [Page 2]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Applicability Statement . . . . . . . . . . . . . . . . . 4
1.2. Use of the Mechanism . . . . . . . . . . . . . . . . . . . 4
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. SIP Events for VoIP Quality Reporting . . . . . . . . . . . . 6
3.1. SUBSCRIBE NOTIFY Method . . . . . . . . . . . . . . . . . 6
3.2. PUBLISH Method . . . . . . . . . . . . . . . . . . . . . . 6
3.3. Multi-Party and Multi-Segment Calls . . . . . . . . . . . 7
3.4. Overload Avoidance . . . . . . . . . . . . . . . . . . . . 7
4. Event Package Formal Definition . . . . . . . . . . . . . . . 8
4.1. Event Package Name . . . . . . . . . . . . . . . . . . . . 8
4.2. Event Package Parameters . . . . . . . . . . . . . . . . . 8
4.3. SUBSCRIBE Bodies . . . . . . . . . . . . . . . . . . . . . 8
4.4. Subscribe Duration . . . . . . . . . . . . . . . . . . . . 8
4.5. NOTIFY Bodies . . . . . . . . . . . . . . . . . . . . . . 8
4.6. Voice Quality Event and Semantics . . . . . . . . . . . . 9
4.6.1. ABNF Syntax Definition . . . . . . . . . . . . . . . . 10
4.6.2. Parameter Definitions and Mappings . . . . . . . . . . 20
4.7. Message Flow and Syntax Examples . . . . . . . . . . . . . 28
4.7.1. End of Session Report using NOTIFY . . . . . . . . . . 28
4.7.2. Mid Session Threshold Violation using NOTIFY . . . . . 30
4.7.3. End of Session Report using PUBLISH . . . . . . . . . 32
4.7.4. Alert Report using PUBLISH . . . . . . . . . . . . . . 35
4.8. Configuration Dataset for vq-rtcpxr Events . . . . . . . . 37
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 37
5.1. SIP Event Package Registration . . . . . . . . . . . . . . 37
5.2. application/vq-rtcp-xr MIME Registration . . . . . . . . . 37
6. Security Considerations . . . . . . . . . . . . . . . . . . . 38
7. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 38
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.1. Normative References . . . . . . . . . . . . . . . . . . . 38
8.2. Informative References . . . . . . . . . . . . . . . . . . 39
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 39
Pendleton, et al. Expires September 6, 2010 [Page 3]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
1. Introduction
Real time communications over IP networks use SIP for signaling with
RTP/RTCP for media transport and reporting respectively. These
protocols are very flexible and can support an extremely wide
spectrum of usage scenarios. For this reason, extensions to these
protocols must be specified in the context of a specific usage
scenario. In this memo, extensions to SIP are proposed to support
the reporting of RTP Control Protocol Extended Reports [4] metrics.
1.1. Applicability Statement
RTP is utilized in many different architectures and topologies. RFC
5117 [13] lists and describes the following topologies: point to
point, point to multipoint using multicast, point to multipoint using
the RFC 3550 translator, point to multipoint using the RFC 3550 mixer
model, point to multipoint using video switching MCUs, point to
multipoint using RTCP-terminating MCU, and non-symmetric mixer/
translators. As the abstract to this document points out, this
specification is for reporting quality of Voice over Internet
Protocol(VoIP) sessions. As such, only the first topology, point to
point, is currently supported by this specification. This reflects
both current VoIP deployments which are predominantly point to point
using unicast, and also the state of research in the area of quality.
How to accurately report the quality of a multipart conference or a
session involving multiple hops through translators and mixers is
currently an area of research in the industry. However, this
mechanism can easily be used for centrally mixed conference calls, in
which each leg of the conferences is just a point to point call.
This mechanism could be extended to cover additional RTP topologies
in the future once these topics progress out of the realm of research
and into actual Internet deployments.
1.2. Use of the Mechanism
RTCP reports are usually sent to other participating endpoints in a
session which can make collection of performance information by
administration or management systems too complex. In the usage
scenarios addressed in this memo, the data contained in RTCP XR VoIP
metrics reports (RFC3611 [4]) are forwarded to a central collection
server systems using SIP.
Applications residing in the server or elsewhere can aid in network
management to alleviate bandwidth constraints and also to support
customer service by identifying and acknowledging calls of poor
quality. Specifying such applications are however beyond the scope
of this paper.
Pendleton, et al. Expires September 6, 2010 [Page 4]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
There is a large portfolio of quality parameters that can be
associated with VoIP, but only a minimal necessary number of
parameters are included on the RTCP-XR reports:
1. The codec type, as resulting from the SDP offer-answer
negotiation in SIP,
2. The burst gap loss density and max gap duration, since voice cut-
outs are the most annoying quality impairment in VoIP,
3. Round trip delay because it is critical to conversational
quality,
4. Conversational quality as a catch-all for other voice quality
impairments, such as random distributed packet loss, jitter, annoying
silent suppression effects, etc.
In specific usage scenarios where other parameters are required,
designers can include other parameters beyond the scope of this
paper.
RTCP reports are best effort only, and though very useful have a
number of limitations as discussed in [3]. This must be considered
when using RTCP reports in managed networks.
This document defines a new SIP event package, vq-rtcpxr, and a new
MIME type, application/vq-rtcpxr, that enable the collection and
reporting of metrics that measure quality for RTP [3] sessions. The
definitions of the metrics used in the event package are based on
RTCP Extended Reports [4] and RTCP [3]; a mapping between the SIP
event parameters and the parameters within the aforementioned RFC's
is defined within this document in section 4.6.2.
Monitoring of voice quality is believed to be the highest priority
for usage of this mechanism and as such, the metrics in the event
package are largely tailored for voice quality measurements. The
event package is designed to be extensible. However the negotiation
of such extensions is not defined in this document.
The event package supports reporting both the voice quality metrics
for both inbound and outbound directions. Voice quality metrics for
the inbound direction can generally be computed locally by the
reporting endpoint however voice quality metrics for the outbound
direction are computed by the remote endpoint and sent to the
reporting endpoint using the RTCP Extended Reports [4].
Configuration of usage of the event package is not covered in this
document. It is the recommendation of this document that the SIP
Pendleton, et al. Expires September 6, 2010 [Page 5]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
configuration framework [8] be used. The authors have defined a
configuration dataset that would facilitate this support in section
5.8.
The event package SHOULD be used with the SUBSCRIBE/NOTIFY method
however it MAY be also used with the PUBLISH method for backward
compatibility with some existing implementations. Message flow
examples for both methods are provided in this document.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119 [1].
3. SIP Events for VoIP Quality Reporting
This document defines a SIP events package [5] for Voice over IP
performance reporting. A SIP UA can send these events to an entity
which can make the information available to other applications. For
purposes of illustration, the entities involved in SIP vq-rtcpxr
event reporting will be referred to as follows:
o REPORTER is an entity involved in the measurement and reporting of
media quality i.e. the SIP UA involved in a media session.
o COLLECTOR is an entity that receives SIP vq-rtcpxr events. A
COLLECTOR may be a proxy server or another entity that is capable of
supporting SIP vq-rtcpxr events.
3.1. SUBSCRIBE NOTIFY Method
The COLLECTOR SHALL send a SUBSCRIBE to the REPORTER to explicitly
establish the relationship. The REPORTER SHOULD send the voice
quality metric reports using the NOTIFY method. The REPORTER MUST
NOT send any vq-rtcpxr events if a COLLECTOR address has not been
configured. The REPORTER populates the Request-URI according to the
rules for an in-dialog request. The COLLECTOR MAY send a SUBSCRIBE
to a SIP Proxy acting on behalf of the reporting SIP UA's.
3.2. PUBLISH Method
A SIP UA that supports this specification MAY also send the service
quality metric reports using the PUBLISH method, however this
approach SHOULD NOT be used in unmanaged Internet services. The
PUBLISH method MAY be supported for backward compatibility with
Pendleton, et al. Expires September 6, 2010 [Page 6]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
existing implementations.
The REPORTER MAY therefore populate the Request-URI of the PUBLISH
method with the address of the COLLECTOR. To ensure security of SIP
proxies and the COLLECTOR, the REPORTER MUST be configured with the
address of the COLLECTOR, preferably using the SIP UA configuration
framework [8], as described in section 5.8.
It is recommended that the REPORTER send an OPTIONS message to the
COLLECTOR to ensure support of the PUBLISH message.
3.3. Multi-Party and Multi-Segment Calls
A voice quality metric report may be sent for each session
terminating at the REPORTER and may contain multiple report bodies.
For a multi-party call the report MAY contain report bodies for the
session between the reporting endpoint and each remote endpoint for
which there was an RTP session during the call.
Multi-party services such as call hold and call transfer can result
in the user participating in a series of concatenated sessions,
potentially with different choices of codec or sample rate, although
these may be perceived by the user as a single call. A REPORTER MAY
send a voice quality metric report at the end of each session or MAY
send a single voice quality metric report containing a report body
for each segment of the call.
3.4. Overload Avoidance
Users of this extension should ensure they implement general SIP
mechanisms for avoiding overload. For instance, an overloaded proxy
or COLLECTOR MUST send a 503 Service Unavailable or other 5xx esponse
with an appropriate Retry-After time specified. REPORTERs MUST act
on these responses and respect the retry after time interval. In
addition, future SIP extensions to better handle overload as covered
in [14] should be followed as they are standardized.
To avoid overload of SIP Proxies or COLLECTORS it is important to do
capacity planning and to minimize the number of reports that are
sent.
Approaches to avoiding overload include:
a. Send only one report at the end of each call
b. Use interval reports only on "problem" calls that are being
closely monitored
Pendleton, et al. Expires September 6, 2010 [Page 7]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
c. Limit the number of alerts that can be sent to a maximum of one
per call.
4. Event Package Formal Definition
4.1. Event Package Name
This document defines a SIP Event Package as defined in RFC 3265 [5].
4.2. Event Package Parameters
No event package parameters are defined.
4.3. SUBSCRIBE Bodies
SUBSCRIBE bodies are described by this specification.
4.4. Subscribe Duration
Subscriptions to this event package MAY range from minutes to weeks.
Subscriptions in hours or days are more typical and are RECOMMENDED.
The default subscription duration for this event package is one hour.
4.5. NOTIFY Bodies
There are three notify bodies: a Session report, an Interval session
report, and an Alert report.
The Session report SHOULD be used for reporting when a voice media
session terminates or when a media change occurs, such as a codec
change or a session forks and MUST NOT be used for reporting at
arbitrary points in time. This report MUST be used for cumulative
metric reporting and the report timestamps MUST be from the start of
a media session to the time at which the report is generated.
The Interval report SHOULD be used for periodic or interval reporting
and MUST NOT be used for reporting for the complete media session.
This report is intended to capture short duration metric reporting
and the report intervals SHOULD be non-overlapping time windows.
The Alert report MAY be used when voice quality degrades during a
session. The time window to which an Alert report relates MAY be a
short time interval or from the start of the call to the point the
alert is generated; this time window SHOULD be selected to provide
the most useful information to support problem diagnosis.
Session, Interval and Alert reports MUST populate the metrics with
Pendleton, et al. Expires September 6, 2010 [Page 8]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
values that are measured over the interval explicitly defined by the
"start" and "stop" timestamps.
Voice quality summary reports reference only one codec (payload
type). This payload type SHOULD be the main voice payload, not
comfort noise or telephone events payloads. For applications that
consistently and rapidly switch codecs, the most used codec should be
reported. All values in the report, such as IP addresses, SSRC, etc
represent those values as received by the REPORTER. In some
scenarios, these may not be the same on either end of the session -
the COLLECTOR will need logic to be able to put these sessions
together. The values of parameters such as sample rate, frame
duration, frame octets, packets per second, round trip delay, etc
depend on the type of report they are present in. If present in a
Session or an Interval report, they represent average values over the
session or interval. If present in an Alert report, they represent
instantaneous values.
The REPORTER always shares local quality reporting information and
should, if possible, share remote quality reporting information.
This remote quality could be available from received RTCP-XR reports
or other sources. Reporting this is useful in cases where the other
end might support RTCP-XR but not this voice quality reporting.
This specification defines a new MIME type application/vq-rtcpxr
which is a text encoding of the RTCP and RTCP-XR statistics with some
additional metrics and correlation information.
4.6. Voice Quality Event and Semantics
This section describes the syntax extensions required for event
publication in SIP. The formal syntax definitions described in this
section are expressed in the Augmented BNF [6] format used in SIP
[2], and contains references to elements defined therein.
Additionally, the definition of the timestamp format is provided in
[7]. Note that most of the parameters are optional. In practice,
most implementations will send a subset of the parameters. It is not
the intention of this document to define what parameters may or may
not be useful for monitoring the quality of a voice session, but to
enable reporting of voice quality. As such, the syntax allows the
implementer to choose which metrics are most appropriate for their
solution. As there are no "invalid", "unknown", or "not applicable"
values in the syntax, the intention is to exclude any parameters for
which values are not available, not applicable, or unknown.
The authors recognize that implementers may need to add new parameter
lines to the reports and new metrics to the existing parameter lines.
Pendleton, et al. Expires September 6, 2010 [Page 9]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
The extension tokens are intended to fulfill this need.
4.6.1. ABNF Syntax Definition
VQReportEvent = AlertReport / SessionReport / IntervalReport
SessionReport = "VQSessionReport" [HCOLON CallTerm] CRLF
LocalMetrics [CRLF RemoteMetrics]
[DialogID]
; CallTerm indicates the final report of a session.
IntervalReport = "VQIntervalReport" [HCOLON CallTerm] CRLF
LocalMetrics [CRLF RemoteMetrics]
[DialogID]
LocalMetrics = "LocalMetrics" HCOLON CRLF Metrics
RemoteMetrics = "RemoteMetrics" HCOLON CRLF Metrics
AlertReport = "VQAlertReport" HCOLON
MetricType WSP Severity WSP Direction CRLF
LocalMetrics [CRLF RemoteMetrics]
[DialogID]
Metrics = TimeStamps CRLF
[SessionDescription CRLF]
CallID CRLF
FromID CRLF
ToID CRLF
OrigID CRLF
LocalAddr CRLF
RemoteAddr CRLF
[LocalMACAddr CRLF]
[RemoteMACAddr CRLF]
[JitterBuffer CRLF]
[PacketLoss CRLF]
[BurstGapLoss CRLF]
[Delay CRLF]
[Signal CRLF]
[QualityEstimates CRLF]
*(Extension CRLF)
; Timestamps are provided in Coordinated Universal Time (UTC)
; using the ABNF format provided in RFC3339,
; "Date and Time on the Internet: Timestamps"
Pendleton, et al. Expires September 6, 2010 [Page 10]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
; These timestamps SHOULD reflect, as closely as
; possible, the actual time during which the media session
; was running to enable correlation to events occurring
; in the network infrastructure and to accounting records
TimeStamps = "Timestamps" HCOLON StartTime WSP StopTime
StartTime = "START" EQUAL date-time
StopTime = "STOP" EQUAL date-time
; SessionDescription provides a shortened version of the
; session SDP but contains only the relevant parameters for
; session quality reporting purposes
SessionDescription = "SessionDesc" HCOLON
[PayloadType WSP]
[MediaSubtype WSP]
[PayloadDesc WSP]
[SampleRate WSP]
[PacketsPerSecond WSP]
[FrameDuration WSP]
[FrameOctets WSP]
[FramesPerPacket WSP]
[FmtpOptions WSP]
[PacketLossConcealment WSP]
[SilenceSuppressionState]
*(WSP Extension)
; PayloadType provides the PT parameter used in the RTP packets
PayloadType = "PT" EQUAL (1*3DIGIT)
; PayloadDesc provides a text description of the codec
; This parameter SHOULD use the IANA registry for
; media-type names defined by RFC 4855 where it unambiguously
; defines the codec. Refer to:
; http://www.iana.org/assignments/media-types/audio/
PayloadDesc = "PD" EQUAL (word / DQUOTE word-plus DQUOTE)
; SampleRate reports the rate at which voice was sampled
; in the case of narrowband codecs, this value will typically
; be 8000.
; For codecs that are able to change sample rates the lowest and
; highest sample rates MUST be reported (e.g. 8000;16000).
SampleRate = "SR" EQUAL (1*6DIGIT) *(SEMI (1*66DIGIT))
; FrameDuration can be combined with the FramesPerPacket
Pendleton, et al. Expires September 6, 2010 [Page 11]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
; to determine the packetization rate; the units for
; FrameDuration are milliseconds. NOTE: for frame based codecs,
; each frame constitutes a single frame; for sample-based codecs,
; a "frame" refers to the set of samples carried in an RTP packet
FrameDuration = "FD" EQUAL (1*4DIGIT)
; FrameOctets provides the number of octets in each frame
; at the time the report is generated (i.e. last value)
; This MAY be used where FrameDuration is not available
; NOTE: for frame-based codecs, each frame constitutes a single frame;
; for sample-based codecs, a "frame" refers to the set of samples carried
; in an RTP packet.
FrameOctets = "FO" EQUAL (1*5DIGIT)
; FramesPerPacket provides the number of frames in each RTP
; packet at the time the report is generated
; NOTE: for frame based codecs, each frame constitutes a single frame;
; for sample-based codecs, a "frame" refers to the set of samples carried
; in an RTP packet
FramesPerPacket = "FPP" EQUAL (1*2DIGIT)
; Packets per second provides the average number of packets
; that are transmitted per second, as at the time the report is
; generated.
PacketsPerSecond = "PPS" EQUAL (1*5DIGIT)
; FMTP options from SDP. Note that the parameter is delineated
; by " " to avoid parsing issues in transitioning between SDP
; and SIP parsing
FmtpOptions = "FMTP" EQUAL DQUOTE word-plus DQUOTE
; PacketLossConcealment indicates whether a PLC algorithm was
; or is being used for the session. The values follow the same
; numbering convention as RFC 3611[4].
; 0 - unspecified
; 1 - disabled
; 2 - enhanced
; 3 - standard
PacketLossConcealment = "PLC" EQUAL ("0" / "1" / "2" / "3")
; SilenceSuppressionState indicates whether silence suppression,
; also known as Voice Activity Detection (VAD) is enabled.
Pendleton, et al. Expires September 6, 2010 [Page 12]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
SilenceSuppressionState = "SSUP" EQUAL ("on" / "off")
; CallId provides the call id from the SIP dialog
CallID = "CallID" HCOLON Call-ID-Parm
; FromID provides the identification of the reporting endpoint
; of the media session [2].
FromID = "FromID" HCOLON (name-addr/addr-spec)
; ToID provides the identification of the remote endpoint
; of the media session [2].
ToID = "ToID" HCOLON (name-addr/addr-spec)
; Originator specifies provides the identification of the
; endpoint which originated the session
OrigID = "OrigID" HCOLON (name-addr/addr-spec)
; LocalAddr provides the IP address, port and ssrc of the
; endpoint/UA which is the receiving end of the stream being
; measured.
LocalAddr = "LocalAddr" HCOLON IPAddress WSP Port WSP Ssrc
; RemoteAddr provides the IP address, port and ssrc of the
; the source of the stream being measured.
RemoteAddr = "RemoteAddr" HCOLON IPAddress WSP Port WSP Ssrc
; LocalMACAddr provides the MAC address
; of the local SIP device
LocalMACAddr = "LocalMAC" HCOLON hex2 *(":" hex2)
; RemoteMACAddr provides the MAC address
; of the remote SIP device
RemoteMACAddr = "RemoteMAC" HCOLON hex2 *(":" hex2)
; For clarification, the LocalAddr in the LocalMetrics report
; MUST be the RemoteAddr in the RemoteMetrics report.
IPAddress = "IP" EQUAL IPv6address / IPv4address
Port = "PORT" EQUAL 1*DIGIT
Ssrc = "SSRC" EQUAL ( ''0x'' 1*8HEXDIG)
Pendleton, et al. Expires September 6, 2010 [Page 13]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
JitterBuffer = "JitterBuffer" HCOLON
[JitterBufferAdaptive WSP]
[JitterBufferRate WSP]
[JitterBufferNominal WSP]
[JitterBufferMax WSP]
[JitterBufferAbsMax]
*(WSP Extension)
; JitterBufferAdaptive indicates whether the jitter buffer in
; the endpoint is adaptive, static, or unknown.
; The values follow the same numbering convention as RFC3611.
; For more details, please refer to that document.
; 0 - unknown
; 1 - reserved
; 2 - non-adaptive
; 3 - adaptive
JitterBufferAdaptive = "JBA" EQUAL ("0" / "1" / "2" / "3")
; JitterBuffer metric definitions are provided in RFC3611
JitterBufferRate = "JBR" EQUAL (1*2DIGIT) ;0-15
JitterBufferNominal = "JBN" EQUAL (1*5DIGIT) ;0-65535
JitterBufferMax = "JBM" EQUAL (1*5DIGIT) ;0-65535
JitterBufferAbsMax = "JBX" EQUAL (1*5DIGIT) ;0-65535
; PacketLoss metric definitions are provided in RFC3611
PacketLoss = "PacketLoss" HCOLON
[NetworkPacketLossRate WSP]
[JitterBufferDiscardRate]
*(WSP Extension)
NetworkPacketLossRate =
"NLR" EQUAL (1*3DIGIT ["." 1*2DIGIT]) ;percentage
JitterBufferDiscardRate =
"JDR" EQUAL (1*3DIGIT ["." 1*2DIGIT]) ;percentage
; BurstGapLoss metric definitions are provided in RFC3611 [4]
BurstGapLoss = "BurstGapLoss" HCOLON
[BurstLossDensity WSP]
[BurstDuration WSP]
Pendleton, et al. Expires September 6, 2010 [Page 14]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
[GapLossDensity WSP]
[GapDuration WSP]
[MinimumGapThreshold]
*(WSP Extension)
BurstLossDensity =
"BLD" EQUAL (1*3DIGIT ["." 1*2DIGIT]) ;percentage
BurstDuration =
"BD" EQUAL (1*7DIGIT) ;0-3,600,000 -- milliseconds
GapLossDensity =
"GLD" EQUAL (1*3DIGIT ["." 1*2DIGIT]) ;percentage
GapDuration =
"GD" EQUAL (1*7DIGIT) ;0-3,600,000 -- milliseconds
MinimumGapThreshold =
"GMIN" EQUAL (1*3DIGIT) ;1-255
Delay = "Delay" HCOLON
[RoundTripDelay WSP]
[EndSystemDelay WSP]
[OneWayDelay WSP]
[SymmOneWayDelay WSP]
[InterarrivalJitter WSP]
[MeanAbsoluteJitter]
*(WSP Extension)
; RoundTripDelay SHALL be measured as defined in RFC3550 [3].
RoundTripDelay = "RTD" EQUAL (1*5DIGIT) ;0-65535
; EndSystemDelay metric is defined in RFC 3611 [4]
EndSystemDelay = "ESD" EQUAL (1*5DIGIT) ;0-65535
; OneWayDelay is defined in RFC2679
OneWayDelay = "OWD" EQUAL (1*5DIGIT) ;0-65535
; SymmOneWayDelay is defined as half the sum of RoundTripDelay
; and the EndSystemDelay values for both endpoints.
SymmOneWayDelay = "SOWD" EQUAL (1*5DIGIT); 0-65535
; Interarrival Jitter is calculated as defined RFC 3550
Pendleton, et al. Expires September 6, 2010 [Page 15]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
; and converted into milliseconds
InterarrivalJitter = "IAJ" EQUAL (1*5DIGIT) ;0-65535 ms
; Mean Absolute Jitter is measured as defined
; by ITU-T G.1020 [10] where it is known as MAPDV
MeanAbsoluteJitter = "MAJ" EQUAL (1*5DIGIT);0-65535
; Signal metrics definitions are provided in RFC 3611
Signal = "Signal" HCOLON
[SignalLevel WSP]
[NoiseLevel WSP]
[ResidualEchoReturnLoss]
*(WSP Extension)
; SignalLevel will normally be a negative value
; the absence of the negative sign indicates a positive value
; where the signal level is negative, the sign MUST be
; included.This metric applies to the speech signal decoded
; from the received packet stream.
SignalLevel = "SL" EQUAL (["-"] 1*2DIGIT)
; NoiseLevel will normally be negative and the sign MUST be
; explicitly included.
; The absence of a sign indicates a positive value
; This metric applies to the speech signal decoded from the
; received packet stream.
NoiseLevel = "NL" EQUAL (["-"] 1*2DIGIT)
; Residual Echo Return Loss (RERL) the ratio between
; the original signal and the echo level as measured after
; echo cancellation or suppression has been applied.
; Expressed in decibels (dB). This is typically a positive
; value.
; This metric relates to the proportion of the speech signal
; decoded from the received packet stream that is reflected
; back in the encoded speech signal output in the transmitted
; packet stream (i.e. will affect the REMOTE user's
; conversational quality). To support the diagnosis of echo
; related problems experienced by the local user of the device
; generating a report according to this document, the value of
; RERL reported via the RTCP XR VoIP Metrics payload SHOULD be
; reported in the RemoteMetrics set of data.
Pendleton, et al. Expires September 6, 2010 [Page 16]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
ResidualEchoReturnLoss = "RERL" EQUAL (1*3DIGIT)
; Voice Quality estimation metrics
; Each quality estimate has an optional associated algorithm.
; These fields permit the implementation to use a variety
; of different calculation methods for each type of metric
QualityEstimates = "QualityEst" HCOLON
[ListeningQualityR WSP]
[RLQEstAlg WSP]
[ConversationalQualityR WSP]
[RCQEstAlg WSP]
[ExternalR-In WSP]
[ExtRInEstAlg WSP]
[ExternalR-Out WSP]
[ExtROutEstAlg WSP]
[MOS-LQ WSP]
[MOSLQEstAlg WSP]
[MOS-CQ WSP]
[MOSCQEstAlg WSP]
[QoEEstAlg]
*(WSP Extension)
ListeningQualityR = "RLQ" EQUAL (1*3DIGIT) ; 0 - 120
RLQEstAlg = "RLQEstAlg" EQUAL word ; "P.564", or other
ConversationalQualityR = "RCQ" EQUAL (1*3DIGIT) ; 0 - 120
RCQEstAlg = "RCQEstAlg" EQUAL word ; "P.564", or other
; ExternalR-In is measured by the local endpoint for incoming
; connection on "other" side of this endpoint
; e.g. Phone A <---> Bridge <----> Phone B
; ListeningQualityR = quality for Phone A ----> Bridge path
; ExternalR-In = quality for Bridge <---- Phone B path
ExternalR-In = "EXTRI" EQUAL (1*3DIGIT) ; 0 - 120
ExtRInEstAlg = "ExtRIEstAlg" EQUAL word ; "P.564" or other
; ExternalR-Out is copied from RTCP XR message received from the
; remote endpoint on "other" side of this endpoint
; e.g. Phone A <---> Bridge <----> Phone B
; ExternalR-Out = quality for Bridge -----> Phone B path
ExternalR-Out = "EXTRO" EQUAL (1*3DIGIT) ; 0 - 120
Pendleton, et al. Expires September 6, 2010 [Page 17]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
ExtROutEstAlg = "ExtROEstAlg" EQUAL word ; "P.564" or other
MOS-LQ = "MOSLQ" EQUAL (DIGIT ["." 1*3DIGIT]) ; 0.0 - 4.9
MOSLQEstAlg = "MOSLQEstAlg" EQUAL word ; "P.564" or other
MOS-CQ = "MOSCQ" EQUAL (DIGIT ["." 1*3DIGIT]) ; 0.0 - 4.9
MOSCQEstAlg = "MOSCQEstAlg" EQUAL word ; "P.564" or other
; QoEEstAlg provides an alternative to the separate
; estimation algorithms for use when the same algorithm
; is used for all measurements
QoEEstAlg = "QoEEstAlg" EQUAL word ; "P.564" or other
; DialogID provides the identification of the dialog with
; which the media session is related. This value is taken
; from the SIP header.
DialogID = "DialogID" COLON Call-ID-Parm *(SEMI did-parm)
did-parm = to-tag / from-tag / word
to-tag = "to-tag" EQUAL token
from-tag = "from-tag" EQUAL token
; MetricType provides the metric on which a notification of
; threshold violation was based. The more commonly used metrics
; for alerting purposes are included here explicitly, using the
; character encoding that represents the parameter in
; this ABNF. The Extension parameter can be used to provide
; metrics that are not defined by this draft.
MetricType = "Type" EQUAL "RLQ" / "RCQ" / "EXTR" /
"MOSLQ" / "MOSCQ" /
"BD" / "NLR" / "JDR" /
"RTD" / "ESD" / "IAJ" /
"RERL" / "SL" / "NL" / Extension
Direction = "Dir" EQUAL "local" / "remote"
Severity = "Severity" EQUAL "Warning" / "Critical" /
"Clear"
Call-ID-Parm = word [ "@" word ]
; General ABNF notation from RFC5234
Pendleton, et al. Expires September 6, 2010 [Page 18]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
CRLF = %x0D.0A
DIGIT = %x30-39
WSP = SP / HTAB ; white space
SP = " "
HTAB = %x09 ; horizontal tab
HEXDIG = DIGIT / "A" / "B" / "C" / "D" / "E" / "F" /
"a" / "b" / "c" / "d" / "e" / "f"
DQUOTE = %x22 ; " (Double Quote)
ALPHA = %x41-5A / %x61-7A ; A-Z / a-z
; ABNF notation from RFC3261
alphanum = ALPHA / DIGIT
LWS = [*WSP CRLF] 1*WSP ; linear whitespace
SWS = [LWS] ; sep whitespace
SEMI = SWS ";" SWS ; semicolon
EQUAL = SWS "=" SWS ; equal
COLON = SWS ":" SWS ; colon
HCOLON = *( SP / HTAB ) ":" SWS
token = 1*(alphanum / "-" / "." / "!" / "%" / "*"
/ "_" / "+" / "`" / "'" / "~" )
IPv4address = 1*3DIGIT "." 1*3DIGIT "." 1*3DIGIT "." 1*3DIGIT
IPv6address = hexpart [ ":" IPv4address ]
hexpart = hexseq / hexseq "::" [ hexseq ] / "::"
[ hexseq ]
hexseq = hex4 *( ":" hex4)
hex4 = 1*4HEXDIG
hex2 = 2HEXDIG
; ABNF notation from RFC3339
date-fullyear = 4DIGIT ; e.g. 2006
date-month = 2DIGIT ; e.g. 01 or 11
date-mday = 2DIGIT ; e.g. 02 or 22
time-hour = 2DIGIT ; e.g. 01 or 13
time-minute = 2DIGIT ; e.g. 03 or 55
time-second = 2DIGIT ; e.g. 01 or 59
time-secfrac = "." 1*DIGIT
time-numoffset = ("+" / "-") time-hour ":" time-minute
time-offset = "Z" / time-numoffset
partial-time = time-hour ":" time-minute ":" time-second
[time-secfrac]
full-date = date-fullyear "-" date-month "-" date-mday
full-time = partial-time time-offset
date-time = full-date "T" full-time
Pendleton, et al. Expires September 6, 2010 [Page 19]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
; Miscellaneous definitions
;
Extension = word-plus
word = 1*(alphanum / "-" / "." / "!" / "%" / "*" /
"_" / "+" / "`" / "'" / "~" /
"(" / ")" / "<" / ">" /
":" / "\" / DQUOTE /
"/" / "[" / "]" / "?" )
word-plus = 1*(alphanum / "-" / "." / "!" / "%" / "*" /
"_" / "+" / "`" / "'" / "~" /
"(" / ")" / "<" / ">" / ":" /
"\" / "/" / "[" / "]" / "?" /
"{" / "}" / "=" / " ")
4.6.2. Parameter Definitions and Mappings
Parameter values, codec types and other aspects of the endpoints may
change dynamically during a session. The reported values of metrics
and configuration parameters SHALL be the current value at the time
the report is generated.
The Packet Loss Rate and Packet Discard Rate parameters are
calculated over the period between the starting and ending timestamps
for the report. These are normally calculated from a count of the
number of lost or discarded packets divided by the count of the
number of packets, and hence are based on the current values of these
counters at the time the report was generated.
Packet delay variation, signal level, noise level, echo level are
computed as running or interval averages, based on the appropriate
standard (e.g. RFC3550 for PDV) and the sampled value of these
running averages is reported. Delay, packet size, jitter buffer size
and codec related data may change during a session and the current
value of these parameters is reported as sampled at the time the
report is generated.
4.6.2.1. General mapping percentages from 8 bit, fixed point numbers
RFC3611 uses an 8 bit, fixed point number with the binary point at
the left edge of the field. This value is calculated by dividing the
total number of packets lost by the total number of packets expected
and multiplying the result by 256, and taking the integer part.
For any RTCP XR parameter in this format, to map into the equivalent
Pendleton, et al. Expires September 6, 2010 [Page 20]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
SIP vq-rtcpxr parameter, simply reverse the equation i.e. divide by
256 and taking the integer part.
4.6.2.2. Timestamps
Following SIP and other IETF convention, timestamps are provided in
Coordinated Universal Time (UTC) using the ABNF format provided in
RFC 3339 [7]. These timestamps SHOULD reflect, as closely as
possible, the actual time during which the media session was running
to enable correlation to related events occurring in the network and
to accounting or billing records.
4.6.2.3. SessionDescription
The parameters in this field provide a shortened version of the
session SDP(s), containing only the relevant parameters for session
quality reporting purposes. Where values may change durina a
session, for example a codec may change rate, then the most recent
value of the parameter is reported.
4.6.2.3.1. Payload Type
This is the "payload type" parameter used in the RTP packets i.e. the
codec. This field can also be mapped from the SDP "rtpmap" attribute
field "payload type". IANA registered types SHOULD be used.
4.6.2.3.2. Payload Desc
This parameter a text description of the codec. This parameter
SHOULD use the IANA registry for media-type names where it
unambiguously defines the codec. Refer to:
http://www.iana.org/assignments/media-types/audio/
4.6.2.3.3. Sample Rate
This parameter is mapped from the SDP "rtpmap" attribute field "clock
rate". The field provides the rate at which voice was sampled,
measured in Hertz (Hz).
4.6.2.3.4. Packets Per Second
This parameter is not contained in RTP or SDP but can usually be
obtained from the device codec. Packets per second provides the
(rounded) number of RTP packets that are transmitted per second.
Pendleton, et al. Expires September 6, 2010 [Page 21]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
4.6.2.3.5. Frame Duration
This parameter is not contained in RTP or SDP but can usually be
obtained from the device codec. The field reflects the amount of
voice content in each frame within the RTP payload, measured in
milliseconds. Note this value can be combined with the
FramesPerPacket to determine the packetization rate. Also, where a
sample-based codec is used, a "frame" refers to the set of samples
carried in an RTP packet.
4.6.2.3.6. Frame Octets
This parameter is not contained in RTP or SDP but is usually provided
by the device codec. The field provides the number of octets in each
frame within the RTP payload. This field is usually not provided
when the FrameDuration is provided. Also, where a sample-based codec
is used, a "frame" refers to the set of samples carried in an RTP
packet.
4.6.2.3.7. Frames Per Packet
This parameter is not contained in RTP or SDP but can usually be
obtained from the device codec. This field provides the number of
frames in each RTP packet. Note this value can be combined with the
FrameDuration to determine the packetization rate. Also, where a
sample-based codec is used, a "frame" refers to the set of samples
carried in an RTP packet.
4.6.2.3.8. FMTP Options
This parameter is taken directly from the SDP attribute "fmtp".
4.6.2.3.9. Silence Suppression State
This parameter does not correspond to SDP, RTP, or RTCP XR. It
indicates whether silence suppression, also known as Voice Activity
Detection (VAD) is enabled for the identified session.
4.6.2.3.10. Packet Loss Concealment
This value corresponds to "PLC" in RFC3611 in the VoIP Metrics Report
Block. The values defined by RFC3611 are reused by this
recommendation and therefore no mapping is required.
4.6.2.4. LocalAddr
This field provides the IP address, port and synchronization source
(SSRC) for the session from the perspective of the endpoint that is
Pendleton, et al. Expires September 6, 2010 [Page 22]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
measuring performance. The IPAddress can be IPv4 or IPv6 format.
The SSRC is taken from SDP, RTCP, or RTCP XR input parameters.
In the presence of NAT and where a NAT-traversal mechanism such as
STUN [9] is used, the external IP address can be reported, since the
internal IP address is not visible to the network operator.
4.6.2.5. RemoteAddr
This field provides the IP address, port and ssrc of the session peer
from the perspective of the remote endpoint measuring performance.
In the presence of NAT and where a NAT-traversal mechanism such as
STUN [9] is used, the external IP address can be reported, since the
internal IP address is not visible to the network operator.
4.6.2.6. Jitter Buffer Parameters
4.6.2.6.1. Jitter Buffer Adaptive
This value corresponds to "JBA" in RFC3611 in the VoIP Metrics Report
Block. The values defined by RFC3611 are unchanged and therefore no
mapping is required.
4.6.2.6.2. Jitter Buffer Rate
This value corresponds to "JB rate" in RFC3611 in the VoIP Metrics
Report Block. The parameter does not require any conversion.
4.6.2.6.3. Jitter Buffer Nominal
This value corresponds to "JB nominal" in RFC3611 in the VoIP Metrics
Report Block. The parameter does not require any conversion.
4.6.2.6.4. Jitter Buffer Max
This value corresponds to "JB maximum" in RFC3611 in the VoIP Metrics
Report Block. The parameter does not require any conversion.
4.6.2.6.5. Jitter Buffer Abs Max
This value corresponds to "JB abs max" in RFC3611 in the VoIP Metrics
Report Block. The parameter does not require any conversion.
4.6.2.7. Packet Loss Parameters
This value corresponds to "loss rate" in RFC3611 in the VoIP Metrics
Report Block. For conversion, see "General mapping percentages from
8 bit, fixed point numbers".
Pendleton, et al. Expires September 6, 2010 [Page 23]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
4.6.2.7.1. Jitter Buffer Discard Rate
This value corresponds to "discard rate" in RFC3611 in the VoIP
Metrics Report Block. For conversion, see "General mapping
percentages from 8 bit, fixed point numbers".
4.6.2.8. Burst/Gap Parameters
4.6.2.8.1. Burst Loss Density
This value corresponds to "burst density" in RFC3611 in the VoIP
Metrics Report Block. For conversion, see "General mapping
percentages from 8 bit, fixed point numbers".
4.6.2.8.2. Burst Duration
This value corresponds to "burst duration" in RFC3611 in the VoIP
Metrics Report Block. This value requires no conversion; the exact
value sent in an RTCP XR VoIP Metrics Report Block can be included in
the SIP vq-rtcpxr parameter.
4.6.2.8.3. Gap Loss Density
This value corresponds to "gap density" in RFC3611 in the VoIP
metrics Report Block.
4.6.2.8.4. Gap Duration
This value corresponds to "gap duration" in RFC3611 in the VoIP
Metrics Report Block. This value requires no conversion; the exact
value sent in an RTCP XR VoIP Metrics Report Block can be reported.
4.6.2.8.5. Minimum Gap Threshold
This value corresponds to "Gmin" in RFC3611 in the VoIP Metrics
Report Block. This value requires no conversion; the exact value
sent in an RTCP XR VoIP Metrics Report Block can be reported.
4.6.2.9. Delay Parameters
4.6.2.9.1. Round Trip Delay
This value corresponds to "round trip delay" in RFC3611 in the VoIP
Metrics Report Block and may be measured using the method defined in
RFC3550. The parameter is expressed in milliseconds.
Pendleton, et al. Expires September 6, 2010 [Page 24]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
4.6.2.9.2. End System Delay
This value corresponds to "end system delay" in RFC3611 in the VoIP
Metrics Report Block. This parameter does not require any
conversion. The parameter is expressed in milliseconds.
4.6.2.9.3. Symmetric One Way Delay
This value is computed by adding Round Trip Delay to the local and
remote End System Delay and dividing by two.
4.6.2.9.4. One Way Delay
This value SHOULD be measured using the methods defined in IETF
RFC2679. The parameter is expressed in milliseconds.
4.6.2.9.5. Inter-arrival Jitter
Inter-arrival jitter is calculated as defined in RFC 3550 and
converted into milliseconds.
4.6.2.9.6. Mean Absolute Jitter
It is recommended that MAJ be measured as defined in ITU-T G.1020
[10]. This parameter is often referred to as MAPDV. The parameter
is expressed in milliseconds.
4.6.2.10. Signal-related Parameters
4.6.2.10.1. Signal Level
This field corresponds to "signal level" in RFC3611 in the VoIP
Metrics Report Block. This field provides the voice signal relative
level is defined as the ratio of the signal level to a 0 dBm0
reference, expressed in decibels. This value can be used directly
without extra conversion.
4.6.2.10.2. Noise Level
This field corresponds to "noise level" in RFC3611 in the VoIP
Metrics Report Block. This field provides the ratio of the silent
period background noise level to a 0 dBm0 reference, expressed in
decibels. This value can be used directly without extra conversion.
4.6.2.10.3. Residual Echo Return Loss (RERL)
This field corresponds to "RERL" in RFC3611 in the VoIP Metrics
Report Block. This field provides the ratio between the original
Pendleton, et al. Expires September 6, 2010 [Page 25]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
signal and the echo level in decibels, as measured after echo
cancellation or suppression has been applied. This value can be used
directly without extra conversion.
4.6.2.11. Quality Scores
4.6.2.11.1. ListeningQualityR
This field reports the listening quality expressed as an R factor
(per G.107). This does not include the effects of echo or delay.
The range of R is 0-95 for narrowband calls and 0-120 for wideband
calls. Algorithms for computing this value SHOULD be compliant with
ITU-T Recommendations P.564 [11] and G.107 [12].
4.6.2.11.2. RLQEstAlg
This field provides a text name for the algorithm used to estimate
ListeningQualityR.
4.6.2.11.3. ConversationalQualityR
This field corresponds to "R factor" in RFC3611 in the VoIP Metrics
Report Block. This parameter provides a cumulative measurement of
voice quality from the start of the session to the reporting time.
The range of R is 0-95 for narrowband calls and 0-120 for wideband
calls. Algorithms for computing this value SHOULD be compliant with
ITU-T Recommendation P.564 and G.107. Within RFC3611 a reported R
factor of 127 indicates that this parameter is unavailable; in this
case the ConversationalQualityR parameter MUST be omitted from the
vq-rtcpxr event.
4.6.2.11.4. RCQEstAlg
This field provides a text name for the algorithm used to estimate
ConversationalQualityR.
4.6.2.11.5. ExternalR-In
This field corresponds to "ext. R factor" in RFC3611 in the VoIP
Metrics Report Block. This parameter reflects voice quality as
measured by the local endpoint for incoming connection on "other"
side (refer to RFC3611 for a more detailed explanation). The range
of R is 0-95 for narrowband calls and 0-120 for wideband calls.
Algorithms for computing this value SHOULD be compliant with ITU-T
Recommendation P.564 and G.107. Within RFC3611 a reported R factor
of 127 indicates that this parameter is unavailable; in this case the
ConversationalQualityR parameter MUST be omitted from the vq-rtcpxr
event.
Pendleton, et al. Expires September 6, 2010 [Page 26]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
4.6.2.11.6. ExtRInEstAlg
This field provides a text name for the algorithm used to estimate
ExternalR-In.
4.6.2.11.7. ExternalR-Out
This field corresponds to "ext. R factor" in RFC3611 in the VoIP
Metrics Report Block. Here, the value is copied from RTCP XR message
received from the remote endpoint on "other" side of this endpoint
refer to RFC3611 for a more detailed explanation). The range of R is
0-95 for narrowband calls and 0-120 for wideband calls. Algorithms
for computing this value SHOULD be compliant with ITU-T
Recommendation P.564 and G.107. Within RFC3611 a reported R factor
of 127 indicates that this parameter is unavailable; in this case the
ConversationalQualityR parameter SHALL be omitted from the vq-rtcpxr
event.
4.6.2.11.8. ExtROutEstAlg
This field provides a text name for the algorithm used to estimate
ExternalR-Out. Conversion of RFC3611 reported MOS scores for use in
reporting MOS-LQ and MOS-CQ MUST be performed by dividing the RFC3611
reported value by 10 if this value is less than or equal to 50 or
omitting the MOS-xQ parameter if the RFC3611 reported value is 127
(which indicates unavailable).
4.6.2.11.9. MOS-LQ
This field corresponds to "MOSLQ" in RFC3611 in the VoIP Metrics
Report Block. This parameter is the estimated mean opinion score for
listening voice quality on a scale from 1 to 5, in which 5 represents
"Excellent" and 1 represents "Unacceptable". Algorithms for
computing this value SHOULD be compliant with ITU-T Recommendation
P.564 [11]. This field provides a text name for the algorithm used
to estimate MOS-LQ.
4.6.2.11.10. MOS-CQ
This field corresponds to "MOSCQ" in RFC3611 in the VoIP Metrics
Report Block. This parameter is the estimated mean opinion score for
conversation voice quality on a scale from 1 to 5, in which 5
represents excellent and 1 represents unacceptable. Algorithms for
computing this value SHOULD be compliant with ITU-T Recommendation
P.564 with regard to the listening quality element of the computed
MOS score.
Pendleton, et al. Expires September 6, 2010 [Page 27]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
4.6.2.11.11. MOSCQEstAlg
This field provides a text name for the algorithm used to estimate
MOS-CQ.
4.6.2.11.12. QoEEstAlg
This field provides a text description of the algorithm used to
estimate all voice quality metrics. This parameter is provided as an
alternative to the separate estimation algorithms for use when the
same algorithm is used for all measurements.
4.7. Message Flow and Syntax Examples
This section shows a number of message flow examples showing how the
event package works.
4.7.1. End of Session Report using NOTIFY
Alice Proxy/Registrar Collector Bob
| | | |
| | | |
| REGISTER Allow-Event:vq-rtcpxr F1 | |
|------------------->| | |
| 200 OK F2 | | |
|<-------------------| | |
| | SUBSCRIBE Event:vq-rtcpxr F3 |
| |<-------------------| |
| SUBSCRIBE Event:vq-rtcpxr F4 | |
|<-------------------| | |
| 200 OK F5 | | |
|------------------->| | |
| | 200 OK F6 | |
| |------------------->| |
| INVITE F7 | | |
|------------------->| | |
| | INVITE F8 | |
| |---------------------------------------->|
| | 200 OK F9 | |
| |<----------------------------------------|
| 200 OK F10 | | |
|<-------------------| | |
| ACK F11 | | |
|------------------->| | |
| | ACK F12 | |
| |---------------------------------------->|
| RTP | | |
|<============================================================>|
Pendleton, et al. Expires September 6, 2010 [Page 28]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
| RTCP, RTCP XR | |
|<============================================================>|
| | | |
| BYE F13 | | |
|------------------->| BYE F14 | |
| |---------------------------------------->|
| | 200 OK F15 | |
| |<----------------------------------------|
| 200 OK F16 | | |
|<-------------------| | |
| NOTIFY Event:vq-rtcpxr F17 | |
|------------------->| | |
| | NOTIFY Event:vq-rtcpxr F18 |
| |------------------->| |
| | 200 OK F19 | |
| |<-------------------| |
| 200 OK F20 | | |
|<-------------------| | |
Figure 1. Summary report with NOTIFY sent after session termination.
In the call flow depicted in Figure 1, the following message format
is sent in F17:
NOTIFY sip:collector@example.org SIP/2.0
Via: SIP/2.0/UDP pc22.example.org;branch=z9hG4bK3343d7
Max-Forwards: 70
To: <sip:collector@example.org>;tag=43524545
From: Alice <sip:alice@example.org>;tag=a3343df32
Call-ID: 1890463548
CSeq: 4321 NOTIFY
Contact: <sip:alice@pc22.example.org>
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER,
SUBSCRIBE, NOTIFY
Event: vq-rtcpxr
Accept: application/sdp, message/sipfrag
Subscription-State: active;expires=3600
Content-Type: application/vq-rtcpxr
Content-Length: ...
VQSessionReport: CallTerm
LocalMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=0 PD=PCMU SR=8000 FD=20 FO=160 FPP=1 PPS=50
PLC=3 SSUP=on
CallID: 6dg37f1890463
FromID: Alice <sip:alice@example.org>
ToID: Bill <sip:bill@elpmaxe.org>
OrigID: Alice <sip:alice@example.org>
Pendleton, et al. Expires September 6, 2010 [Page 29]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
LocalAddr: IP=10.10.1.100 PORT=5000 SSRC=1a3b5c7d
LocalMAC: 00:1f:5b:cc:21:0f
RemoteAddr:IP=11.1.1.150 PORT=5002 SSRC=0x2468abcd
RemoteMAC: 00:26:08:8e:95:02
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-18 NL=-50 RERL=55
QualityEst:RLQ=88 RCQ=85 EXTRI=90 MOSLQ=4.1 MOSCQ=4.0
QoEEstAlg=P.564
RemoteMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=0 PD=PCMU SR=8000 FD=20 FO=160 FPP=1 PPS=50
PLC=3 SSUP=on
CallID:6dg37f1890463
LocalAddr:IP=11.1.1.150 PORT=5002 SSRC=0x2468abcd
RemoteAddr:IP=10.10.1.100 PORT=5000 SSRC=0x1a3b5c7d
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-21 NL=-45 RERL=55
QualityEst:RLQ=90 RCQ=85 EXTRI=90 MOSLQ=4.3 MOSCQ=4.2
QoEEstAlg=P.564
DialogID:1890463548@alice.example.org;to-tag=8472761;
from-tag=9123dh311
4.7.2. Mid Session Threshold Violation using NOTIFY
Alice Proxy/Registrar Collector Bob
| | | |
| | | |
| REGISTER Allow-Event:vq-rtcpxr F1 | |
|------------------->| | |
| 200 OK F2 | | |
|<-------------------| | |
| | SUBSCRIBE Event:vq-rtcpxr F3 |
| |<-------------------| |
| SUBSCRIBE Event:vq-rtcpxr F4 | |
|<-------------------| | |
| 200 OK F5 | | |
|------------------->| | |
| | 200 OK F6 | |
| |------------------->| |
| INVITE F7 | | |
|------------------->| | |
Pendleton, et al. Expires September 6, 2010 [Page 30]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
| | INVITE F8 | |
| |---------------------------------------->|
| | 200 OK F9 | |
| |<----------------------------------------|
| 200 OK F10 | | |
|<-------------------| | |
| ACK F11 | | |
|------------------->| | |
| | ACK F12 | |
| |---------------------------------------->|
| RTP | | |
|<============================================================>|
| RTCP, RTCP XR | |
|<============================================================>|
| NOTIFY Event:vq-rtcpxr F17 | |
|------------------->| | |
| | NOTIFY Event:vq-rtcpxr F18 |
| |------------------->| |
| | 200 OK F19 | |
| |<-------------------| |
| 200 OK F20 | | |
|<-------------------| | |
| | | |
| BYE F13 | | |
|------------------->| BYE F14 | |
| |---------------------------------------->|
| | 200 OK F15 | |
| |<----------------------------------------|
| 200 OK F16 | | |
|<-------------------| | |
| NOTIFY Event:vq-rtcpxr F17 | |
|------------------->| | |
| | NOTIFY Event:vq-rtcpxr F18 |
| |------------------->| |
| | 200 OK F19 | |
| |<-------------------| |
| 200 OK F20 | | |
|<-------------------| | |
Figure 2. An alert report is sent during the session.
In the call flow depicted in Figure 2, the following message
format is sent in F17:
NOTIFY sip:collector@example.org SIP/2.0
Via: SIP/2.0/UDP pc22.example.org;branch=z9hG4bK3343d7
Max-Forwards: 70
To: <sip:proxy@example.org>
From: Alice <sip:alice@example.org>;tag=a3343df32
Pendleton, et al. Expires September 6, 2010 [Page 31]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
Call-ID: 1890463548
CSeq: 4331 PUBLISH
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER,
SUBSCRIBE, NOTIFY
Event: vq-rtcpxr
Accept: application/sdp, message/sipfrag
Content-Type: application/vq-rtcpxr
Content-Length: ...
VQAlertReport: Type=NLR Severity=Critical Dir=local
LocalMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=18 PD=G729 SR=8000 FD=20 FO=20 FPP=2 PPS=50
FMTP="annexb=no" PLC=3 SSUP=on
CallID: 6dg37f1890463
FromID: Alice <sip:alice@example.org>
ToID: Bill <sip:bill@example.org>
OrigID: Alice <sip:alice@example.org>
LocalAddr:IP=10.10.1.100 PORT=5000 SSRC=0x2468abcd
LocalMAC: 00:1f:5b:cc:21:0f
RemoteAddr:IP=11.1.1.150 PORT=5002 SSRC=1357efff
RemoteMAC: 00:26:08:8e:95:02
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=10.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-21 NL=-50 RERL=55
QualityEst:RLQ=80 RCQ=85 EXTRI=90 MOSLQ=3.5 MOSCQ=3.7 QoEEstAlg=P.564
RemoteMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=18 PD=G729 SR=8000 FD=20 FO=20 FPP=2 PPS=50
FMTP="annexb=no" PLC=3 SSUP=on
CallID: 6dg37f1890463
LocalAddr:IP=11.1.1.150 PORT=5002 SSRC=1357efff
RemoteAddr:IP=10.10.1.100 PORT=5000 SSRC=0x2468abcd
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-21 NL=-45 RERL=55
QualityEst:RLQ=90 RCQ=85 MOSLQ=4.3 MOSCQ=4.2 QoEEstAlg=P.564
DialogID:1890463548@alice.example.org;to-tag=8472761;
from-tag=9123dh311
4.7.3. End of Session Report using PUBLISH
Alice Proxy/Registrar Collector Bob
Pendleton, et al. Expires September 6, 2010 [Page 32]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
| | | |
| | | |
| REGISTER Allow-Event:vq-rtcpxr F1 | |
|------------------->| | |
| 200 OK F2 | | |
|<-------------------| | |
| INVITE F3 | | |
|------------------->| | |
| | INVITE F4 | |
| |---------------------------------------->|
| | 200 OK F5 | |
| |<----------------------------------------|
| 200 OK F6 | | |
|<-------------------| | |
| ACK F7 | | |
|------------------->| | |
| | ACK F8 | |
| |---------------------------------------->|
| RTP | | |
|<============================================================>|
| RTCP | | |
|<============================================================>|
| | | |
| BYE F9 | | |
|------------------->| BYE F10 | |
| |---------------------------------------->|
| | 200 OK F11 | |
| |<----------------------------------------|
| 200 OK F12 | | |
|<-------------------| | |
| PUBLISH Event:vq-rtcpxr F13 | |
|------------------->| | |
| | PUBLISH Event:vq-rtcpxr F14 |
| |------------------->| |
| | 200 OK F15 | |
| |<-------------------| |
| 200 OK F16 | | |
|<-------------------| | |
Figure 3. End of session report sent after session termination.
In the message flow depicted in Figure 3, the following message is
sent in F13.
PUBLISH sip:collector@example.org SIP/2.0
Via: SIP/2.0/UDP pc22.example.org;branch=z9hG4bK3343d7
Max-Forwards: 70
To: <sip:proxy@example.org>
From: Alice <sip:alice@example.org>;tag=a3343df32
Pendleton, et al. Expires September 6, 2010 [Page 33]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
Call-ID: 1890463548
CSeq: 4331 PUBLISH
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER,
SUBSCRIBE, NOTIFY
Event: vq-rtcpxr
Accept: application/sdp, message/sipfrag
Content-Type: application/vq-rtcpxr
Content-Length: ...
VQSessionReport: CallTerm
LocalMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=18 PD=G729 SR=8000 FD=20 FO=20 FPP=2 PPS=50
FMTP="annexb=no" PLC=3 SSUP=on
CallID: 6dg37f1890463
FromID: Alice <sip:alice@example.org>
ToID: Bill <sip:bill@elpmaxe.org>
OrigID: Alice <sip:alice@example.org>
LocalAddr: IP=10.10.1.100 PORT=5000 SSRC=1a3b5c7d
LocalMAC: 00:1f:5b:cc:21:0f
RemoteAddr:IP=11.1.1.150 PORT=5002 SSRC=0x2468abcd
RemoteMAC: 00:26:08:8e:95:02
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-21 NL=-50 RERL=55
QualityEst:RLQ=90 RCQ=85 EXTRI=90 MOSLQ=4.2 MOSCQ=4.3
QoEEstAlg=P.564
RemoteMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=18 PD=G729 SR=8000 FD=20 FO=20 FPP=2 PPS=50
FMTP="annexb=no" PLC=3 SSUP=on
CallID:6dg37f1890463
LocalAddr:IP=11.1.1.150 PORT=5002 SSRC=1357efff
RemoteAddr:IP=10.10.1.100 PORT=5000 SSRC=0x2468abcd
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-21 NL=-45 RERL=55
QualityEst:RLQ=90 RCQ=85 MOSLQ=4.3 MOSCQ=4.2 QoEEstAlg=P.564
DialogID:1890463548@alice.example.org;to-tag=8472761;
from-tag=9123dh311
4.7.4. Alert Report using PUBLISH
Pendleton, et al. Expires September 6, 2010 [Page 34]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
Alice Proxy/Registrar Collector Bob
| | | |
| INVITE F1 | | |
|------------------->| | |
| | INVITE F2 | |
| |---------------------------------------->|
| | 200 OK F3 | |
| |<----------------------------------------|
| 200 OK F4 | | |
|<-------------------| | |
| ACK F5 | | |
|------------------->| | |
| | ACK F6 | |
| |---------------------------------------->|
| RTP | | |
|<============================================================>|
| RTCP | | |
|<============================================================>|
| PUBLISH Event:vq-rtcpxr F7 | |
|------------------->| | |
| | PUBLISH Event:vq-rtcpxr F8 |
| |------------------->| |
| | 200 OK F9 | |
| |<-------------------| |
| 200 OK F10 | | |
|<-------------------| | |
| | | |
| BYE F12 | | |
|------------------->| BYE F13 | |
| |---------------------------------------->|
| | 200 OK F14 | |
| |<----------------------------------------|
| 200 OK F15 | | |
|<-------------------| | |
Figure 4. Alert report message flow
In the message flow depicted in Figure 4, the following message is
sent in F7:
PUBLISH sip:collector@example.org SIP/2.0
Via: SIP/2.0/UDP pc22.example.org;branch=z9hG4bK3343d7
Max-Forwards: 70
To: <sip:collector@example.org>
From: Alice <sip:alice@example.org>;tag=a3343df32
Call-ID: 1890463548
CSeq: 4321 PUBLISH
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER,
Pendleton, et al. Expires September 6, 2010 [Page 35]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
SUBSCRIBE, NOTIFY
Event: vq-rtcpxr
Accept: application/sdp, message/sipfrag
Content-Type: application/vq-rtcpxr
Content-Length: ...
VQAlertReport: Type=RLQ Severity=Warning Dir=local
Metrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=0 PD=PCMU SR=8000 FD=20 FO=160 FPP=1 PPS=50
PLC=3 SSUP=on
CallID: 6dg37f1890463
FromID: Alice <sip:alice@example.org>
ToID: Bill <sip:bill@example.org>
OrigID: Alice <sip:alice@example.org>
LocalAddr: IP=10.10.1.100 PORT=5000 SSRC=1a3b5c7d
LocalMAC: 00:1f:5b:cc:21:0f
RemoteAddr:IP=11.1.1.150 PORT=5002 SSRC=0x2468abcd
RemoteMAC: 00:26:08:8e:95:02
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-12 NL=-30 RERL=55
QualityEst:RLQ=60 RCQ=55 EXTR=90 MOSLQ=2.4 MOSCQ=2.3
QoEEstAlg=P.564
RemoteMetrics:
Timestamps:START=2004-10-10T18:23:43Z STOP=2004-10-01T18:26:02Z
SessionDesc:PT=0 PD=PCMU SR=8000 FD=20 FO=160 FPP=1 PPS=50
PLC=3 SSUP=on
CallID: 6dg37f1890463
LocalAddr:IP=11.1.1.150 PORT=5002 SSRC=9f7e5d3c
RemoteAddr:IP=10.10.1.100 PORT=5000 SSRC=2a4b6c8d
JitterBuffer:JBA=3 JBR=2 JBN=40 JBM=80 JBX=120
PacketLoss:NLR=5.0 JDR=2.0
BurstGapLoss:BLD=0 BD=0 GLD=2.0 GD=500 GMIN=16
Delay:RTD=200 ESD=140 SOWD=200 IAJ=2 MAJ=10
Signal:SL=-23 NL=-60 RERL=55
QualityEst:RLQ=90 RCQ=85 EXTRI=90 MOSLQ=4.2 MOSCQ=4.3
QoEEstAlg=P.564
DialogID:1890463548@alice.example.org;to-tag=8472761;
from-tag=9123dh3111
Pendleton, et al. Expires September 6, 2010 [Page 36]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
4.8. Configuration Dataset for vq-rtcpxr Events
It is the suggestion of the authors that the SIP configuration
framework [8] be used to establish the necessary parameters for usage
of vq-rtcpxr events. A dataset for this purpose should be designed
and documented in a separate draft upon completion of the framework.
5. IANA Considerations
This document registers a new SIP Event Package and a new MIME type.
5.1. SIP Event Package Registration
Package name: vq-rtcpx
Type: package
Contact: Amy Pendleton <aspen@telchemy.com>
Published Specification: This document
5.2. application/vq-rtcp-xr MIME Registration
MIME media type name: application
MIME subtype name: vq-rtcpxr
Mandatory parameters: none
Optional parameters: none
Encoding considerations: text
Security considerations: See next section.
Interoperability considerations: none.
Published specification: This document.
Applications which use this media type: This document type is
being used in notifications of VoIP quality reports.
Additional Information:
Magic Number: None
File Extension: None
Macintosh file type code: "TEXT"
Personal and email address for further information: Amy Pendleton
<aspen@telchemy.com>
Intended usage: COMMON
Author/Change controller: The IETF.
Pendleton, et al. Expires September 6, 2010 [Page 37]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
6. Security Considerations
RTCP reports can contain sensitive information since they can provide
information about the nature and duration of a session established
between two or more endpoints. As a result, any third party wishing
to obtain this information SHOULD be properly authenticated by the
SIP UA using standard SIP mechanisms and according to the
recommendations in [5]. Additionally the event content MAY be
encrypted to ensure confidentiality; the mechanisms for providing
confidentiality are detailed in [2].
7. Contributors
The authors would like to thank Rajesh Kumar, Dave Oran, Tom Redman,
Shane Holthaus and Jack Ford for their comments and input.
8. References
8.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A.,
Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP:
Session Initiation Protocol", RFC 3261, June 2002.
[3] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson,
"RTP: A Transport Protocol for Real-Time Applications", STD 64,
RFC 3550, July 2003.
[4] Friedman, T., Caceres, R., and A. Clark, "RTP Control Protocol
Extended Reports (RTCP XR)", RFC 3611, November 2003.
[5] Roach, A., "Session Initiation Protocol (SIP)-Specific Event
Notification", RFC 3265, June 2002.
[6] Crocker, D. and P. Overell, "Augmented BNF for Syntax
Specifications: ABNF", STD 68, RFC 5234, January 2008.
[7] Klyne, G., Ed. and C. Newman, "Date and Time on the Internet:
Timestamps", RFC 3339, July 2002.
[8] Niemi, A., "Session Initiation Protocol (SIP) Extension for
Event State Publication", RFC 3903, October 2004.
Pendleton, et al. Expires September 6, 2010 [Page 38]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
[9] Channabasappa, S., "A Framework for Session Initiation Protocol
User Agent Profile Delivery",
draft-ietf-sipping-config-framework-17 (work in progress),
February 2010.
[10] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing, "Session
Traversal Utilities for NAT (STUN)", RFC 5389, October 2008.
[11] ITU-T G.1020, "Performance parameter definitions for quality of
speech and other voiceband applications utilizing IP
networks.".
[12] ITU-T P.564, "Conformance testing for voice over IP
transmission quality assessment models.".
[13] ITU-T G.107, "The E-model, a computational model for use in
transmission planning.".
8.2. Informative References
[14] Westerlund, M. and S. Wenger, "RTP Topologies", RFC 5117,
January 2008.
[15] Hilt, V., Noel, E., Shen, C., and A. Abdelal, "Design
Considerations for Session Initiation Protocol (SIP) Overload
Control", draft-ietf-sipping-overload-design-02 (work in
progress), July 2009.
Authors' Addresses
Amy Pendleton
Telchemy Incorporated
Email: aspen@telchemy.com
Alan Clark
Telchemy Incorporated
Email: alan.d.clark@telchemy.com
Pendleton, et al. Expires September 6, 2010 [Page 39]
Internet-Draft SIP Package for Voice Quality Reporting March 2010
Alan Johnston
Avaya
St. Louis, MO 63124
Email: alan.b.johnston@gmail.com
Henry Sinnreich
Unaffiliated
Email: henry.sinnreich@gmail.com
Pendleton, et al. Expires September 6, 2010 [Page 40]