Definitions of Managed Objects
for SNA NAUs
March 06, 1996
Bob Clouston
Cisco Systems
clouston@cisco.com
Zbigniew Kielczewski
Cisco Systems
zkielcze@cisco.com
Kitty Shih
Novell
kmshih@novell.com
Bob Moore
IBM Corporation
remoore@ralvm6.vnet.ibm.com
<draft-ietf-snanau-naumib-00.txt>
1. Status of this Memo
This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas, and
its working groups. Note that other groups may also distribute working
documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months.
Internet-Drafts may be updated, replaced, or obsoleted by other
documents at any time. It is not appropriate to use Internet-Drafts as
reference material or to cite them other than as a working draft or work
in progress.
Expires September 06, 1996 [Page 1]
Internet Draft SNANAU MIB March 1996
To learn the current status of any Internet-Draft, please check the
1id-abstracts.txt listing contained in the Internet-Drafts Shadow
Directories on ds.internic.net, nic.nordu.net, ftp.isi.edu, or
munnari.oz.au.
2. Introduction
This memo defines a portion of the Management Information Base (MIB) for
use with network management protocols in the Internet community. In
particular, it defines objects for managing the configuration,
monitoring and control of Physical Units (PUs) and Logical Units (LUs)
in an SNA environment. PUs and LUs are two types of Network Addressable
Units (NAUs) in the logical structure of an SNA network. NAUs are the
origination or destination points for SNA data streams. This memo
identifies managed objects for PU Type 1.0, 2.0 and Type 2.1 and LU Type
0, 1, 2, 3, 4, 7. The generic objects defined here can also be used to
manage LU 6.2 and any LU-LU session. The SNA terms and overall
architecture are documented in [1].
This memo does not specify a standard for the Internet community.
3. The SNMPv2 Network Management Framework
The Internet-standard Network Management Framework presently consists of
three major components. They are:
o RFC 1902 [2] which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of management.
o STD 17, RFC 1213 [3] which defines MIB-II, the core set of managed
objects for the Internet suite of protocols.
o RFC 1157 [4] and/or RFC 1905 [5] which defines the protocol used
for network access to managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
4. Overview
This document identifies the proposed set of objects for managing the
configuration, monitoring and control of Physical Units (PUs) and
Logical Units (LUs) in an SNA environment. In this document, the name
Expires September 06, 1996 [Page 2]
Internet Draft SNANAU MIB March 1996
"Node" is used to describe SNA Node Type 1.0, 2.0 and Type 2.1 and the
name "LU" is used to describe Logical Unit of Type 0, 1, 2, 3, 4, 7 and
6.2. Note however that only objects common to all PU and LU types are
covered here and LU 6.2 specific objects are not included in this MIB
module.
Highlights of the management functions supported by the SNANAU MIB
module include the following:
o Activation/Deactivation of Nodes via the AdminState object in the
snaNodeTable
o Deactivation of sessions via the OperState object in the
snaLuActSessnTable
o Monitoring and modification of parameters related to Nodes, LUs,
and Node/link associations
o Monitoring of session operational parameters
o PU2.0 operational statistics
o Session operational statistics
o RTM statistics
o Traps for:
+ Node state change
+ Node activation failure
+ LU session BIND failure
This MIB module does not support:
o creation of objects,
o activation or deactivation of LUs, nor
o activation of sessions.
4.1. SNANUAU MIB Structure
The SNANAU MIB module contains three groups of objects:
Expires September 06, 1996 [Page 3]
Internet Draft SNANAU MIB March 1996
o snaNode - objects related to Node configuration, monitoring and
control.
o snaLu - objects related to LU definition, monitoring and control.
o snaMgtTools - objects related to specific management tools well
known in SNA environment.
These groups are described below in more detail.
Many objects are organized into two types of tables: the Admin and Oper
tables.
The "Admin" table contains read-only objects which contain default or
expected configuration values. This MIB does not create or modify
configuration values. The "Oper" table contains objects which provide
current operational values, such as state values or negotiated
parameters, for dynamic or configured objects. Dynamic objects are
created by the Agent system using one of the templates provided in the
"Admin" table. Configured objects usually have a one-to-one
relationship between "Admin" and "Oper" entries. However, some "Admin"
values may have changed since the object became operational, such that
the "Oper" values may no longer be based on the "Admin" values. The
"Admin" entry could even be deleted. For example, some implementations
may allow a link station definition (snaNodeLinkAdminEntry) to be
deleted even while the link station is active (snaNodeLinkOperEntry
still exists). Where appropriate, the "Oper" table may include initial
starting values for objects that can be reconfigured while operational.
How the "Admin" values are changed or deleted is outside the scope of
this MIB.
4.1.1. snaNode group
This table contains objects which describe runtime and operational state
variables for a Node, and an object to change the state of the node.
This table is indexed by the node name.
The snaNodeAdminState object describes the desired operational state of
a Node and is used to change the operational state of a Node.
How an Agent or a Management Station obtains the initial value of each
object at creation time is an implementation specific issue not
Expires September 06, 1996 [Page 4]
Internet Draft SNANAU MIB March 1996
addressed in this memo.
Link-specific configuration objects are contained in a separate MIB
module (e.g., the SNA DLC MIB module) corresponding to link type.
2) snaPu20Table
Each row contains statistics variables and operational variables about a
PU type 2.0.
3) snaNodeLinkAdminTable
This table contains all references to link-specific tables. If a Node
is configured with multiple links, then it will have multiple entries in
this table. The entries in this table can be generated initially, after
startup of SNA service, by the Agent which uses information from Node
configuration file. Subsequent modifications of parameters, creation of
new Node link entries and deletion of entries is possible. The
modifications to this table can be saved in the Node configuration file
for the next startup (i.e., restart or next initialization) of SNA
service, but the mechanism for this function is not defined in this
memo. Each entry contains the configuration information that associates
a Node instance to one link instance. The table indices are the node
name and the link name.
4) snaNodeLinkOperTable
This table contains all references to link- specific tables for
operational parameters. If the Node is configured for multiple links,
then it will have multiple entries in this table. The table indices are
the node name and the link name.
5) snaNodeTraps
Two traps are defined for Nodes. The snaNodeStateChangeTrap indicates
that the operational state of a Node has changed. The
snaNodeActFailTrap indicates the failure of ACTPU received from host.
4.1.2. snaLu group
The snaLu group consists of the following tables:
1) snaLuAdminTable
Table containing LU configuration information. The rows in this table
Expires September 06, 1996 [Page 5]
Internet Draft SNANAU MIB March 1996
cannot be created and deleted by a Management Station. Only objects
which are common to all types of LUs are included in this table. The
entries are indexed by node name and LU name.
2) snaLuOperTable
Table containing dynamic runtime information and control variables
relating to LUs. Only objects which are common to all types of LUs are
included in this table. This table is indexed by node name and LU name.
3) snaLuActSessnTable
This is a table containing objects which describe the operational state
of LU-LU sessions. Only objects which are common to all types of LU-LU
sessions are included in this table. When a session is started, an
entry in the session table is created by the Agent. When a session has
ended, the entry for that session is removed from the session table by
the Agent. Entries are indexed by node name, local LU name, and a
unique session index assigned by the agent.
4) snaLuHistSessTable
This table contains historical information about abnormally terminated
sessions. The table is indexed by an integer which will eventually
wrap.
5)snaLuSessStats
This group has objects that indicate and control gathering of
statistics, as well as the snaLuSessnStatsTable, which is a table
containing dynamic statistics information relating to LU-LU sessions.
5) snaLuTraps
The snaLuActSessBindFailTrap indicates the failure of a BIND request.
4.1.3. snaMgtTools group
This is an optional group. The snaMgtTools group consists of the
following table:
1) snaLuRtmTable
Each row contains Response Time Monitor (RTM) variables for an LU. The
table is indexed by Node and LU indices. Entries correspond to LU 2
Expires September 06, 1996 [Page 6]
Internet Draft SNANAU MIB March 1996
entries in the snaLuAdminTable. A Management Station can read
collection of RTM statistics for a given LU.
4.1.4. Conformance statement
Compliance of the SNMPv2 management entity to the SNANAU MIB is defined
in terms of following conformance units called groups.
Unconditionally mandatory groups: snaNodeGroup, snaLuGroup,
snaSessionGroup.
Conditionally mandatory groups: snaPu20Group - mandatory only for those
entities which implement PU type 2.0. The snaMgtToolsRtmGroup -
mandatory only for those entities which implement LU type 2 and RTM.
Expires September 06, 1996 [Page 7]
Internet Draft SNANAU MIB March 1996
5. Definitions
SNA-NAU-MIB DEFINITIONS ::= BEGIN
-- This MIB module contains objects necessary for management of the
-- following SNA devices: node types 1.0, 2.0, 2.1 and LU types 0, 1,
-- 2, 3, 4, 7. It also contains generic objects which can be used to
-- manage LU 6.2.
-- Naming conventions in this document:
-- The following names are used in object descriptors according to
-- SNA conventions. The name 'PU' or 'node' is used to describe nodes
-- type 1.0, 2.0 or 2.1. The name 'LU' is used to describe logical units
-- of type 0, 1, 2, 3, 4, 7 or 6.2.
IMPORTS
DisplayString, RowPointer, DateAndTime, TEXTUAL-CONVENTION
FROM SNMPv2-TC
Counter32, Gauge32, Integer32, TimeTicks,
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF;
snanauMIB MODULE-IDENTITY
LAST-UPDATED "9603061800Z"
ORGANIZATION "IETF SNA NAU MIB Working Group"
CONTACT-INFO
" Zbigniew Kielczewski
Cisco Systems
7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709, USA
Tel: 1 919 472 2326
E-mail: zkielcze@cisco.com
Kitty Shih
Novell
890 Ross Drive
Sunnyvale, CA 94089
Tel: 1 408 747 4305
E-mail: kmshih@novell.com
Expires September 06, 1996 [Page 8]
Internet Draft SNANAU MIB March 1996
Bob Moore (editor)
IBM Corporation
800 Park Offices Drive
CNMA/664
P.O. Box 12195
Research Triangle Park, NC 27709, USA
Tel: 1 919 254 4436
E-mail: remoore@ralvm6.vnet.ibm.com
"
DESCRIPTION
"This is the MIB module for objects used to
manage SNA devices."
::= { mib-2 34 }
-- ********************************************************************
-- Textual Convention
-- ---------------------------------------------------------------------
SnaSenseData ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"To facilitate their display by a Management Station, sense
data objects in the MIB are represented as DisplayStrings of
size 8. Eight '0' characters indicates that no sense data
identifying an SNA error condition is available."
SYNTAX DisplayString (SIZE (8))
-- ********************************************************************
-- The SNANAU MIB module contains an objects part and a conformance part.
-- Objects are organized into the following groups:
-- (1)snaNode group,
-- (2)snaLu group,
-- (3)snaMgtTools group.
snanauObjects OBJECT IDENTIFIER ::= { snanauMIB 1 }
snaNode OBJECT IDENTIFIER ::= { snanauObjects 1 }
snaLu OBJECT IDENTIFIER ::= { snanauObjects 2 }
snaMgtTools OBJECT IDENTIFIER ::= { snanauObjects 3}
-- ********************************************************************
-- snaNode group
--
-- This group contains Managed Objects related to all node types,
Expires September 06, 1996 [Page 9]
Internet Draft SNANAU MIB March 1996
-- plus some specific objects for type 2.0 nodes.
-- ********************************************************************
-- ********************************************************************
-- With the exception of snaNodeAdminState, objects in this table
-- contain current operational values, such as state values or
-- negotiated parameters, for SNA nodes. snaNodeAdminState provides
-- a Management Station with the ability to activate and deactivate
-- an SNA node.
-- ********************************************************************
snaNodeTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaNodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains dynamic node parameters, which have read-
only access. These objects reflect the actual status of the
node. It also contains an object that a Management Station can
set to activate or deactivate an SNA node."
::= { snaNode 3 }
snaNodeEntry OBJECT-TYPE
SYNTAX SnaNodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The entry contains parameters that describe the state of one
node. The entries are created by the Agent. They have read-
only access."
INDEX { snaNodeName }
::= { snaNodeTable 1 }
SnaNodeEntry ::= SEQUENCE {
snaNodeName DisplayString,
snaNodeAdminState INTEGER,
snaNodeOperState INTEGER,
snaNodeSscpSuppliedName DisplayString,
snaNodeType INTEGER,
snaNodeXidFormat INTEGER,
snaNodeId DisplayString,
snaNodeEnablingMethod INTEGER,
Expires September 06, 1996 [Page 10]
Internet Draft SNANAU MIB March 1996
snaNodeLuTermDefault INTEGER,
snaNodeMaxLu Integer32,
snaNodeStopMethod INTEGER,
snaNodeStartTime DateAndTime,
snaNodeLastStateChange DateAndTime,
snaNodeActFailureReason INTEGER
}
snaNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value indicates the locally-defined name of the node. In
a type 2.1 node, this is a fully qualified name, meaning that
the node name is preceded by the NetId (if present) with a
period as the delimiter."
::= { snaNodeEntry 1 }
snaNodeAdminState OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
active(3),
ready(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Object by which a Management Station can activate or
deactivate a node, by setting the value to active(3) or
inactive(1), respectively. The value ready(5) has no meaning
on a set operation; it is returned in response to a get
operation when no set directed to this object has been
processed by the agent.
If the current value in snaNodeState is 'active(3)', then
setting this object to 'inactive(1)' will initiate the node
shutdown process using the method indicated by
snaNodeStopMethod.
If the current value in snaNodeState is 'inactive(1)', then
setting this object to 'active(3)' will initiate the node's
activation.
A Management Station can always set this object to 'active (3)'
Expires September 06, 1996 [Page 11]
Internet Draft SNANAU MIB March 1996
irrespective of the value in the snaNodeEnablingMethod."
::= { snaNodeEntry 2 }
snaNodeOperState OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
active(2),
waiting(3),
stopping(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the node. The values have the following
meanings:
inactive(1) - the node is ready for activation -or-
an active node has been stopped -or-
a waiting node has returned to the
inactive state.
active(2) - the node is ready and operating.
waiting(3) - a request to have the node activated
has been issued, and the node
is pending activation.
stopping(4) - a request to stop the node has been
issued while the StopMethod normal
or immediate is used."
::= { snaNodeEntry 3 }
snaNodeSscpSuppliedName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the SNA name of the node. This name is
supplied to a PU by the SSCP that activated it. If a value was
not supplied, a zero-length string is returned. In a type 2.1
node, this is a fully qualified name, meaning that the node
name is preceded by the NetId (if present) with a period as the
delimiter."
::= { snaNodeEntry 4 }
snaNodeType OBJECT-TYPE
Expires September 06, 1996 [Page 12]
Internet Draft SNANAU MIB March 1996
SYNTAX INTEGER {
other(1),
pu10(2),
pu20(3),
t21LEN(4),
endNode(5),
networkNode(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the current type of the node."
::= { snaNodeEntry 5 }
snaNodeXidFormat OBJECT-TYPE
SYNTAX INTEGER {
format0(1),
format1(2),
format3(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the type of XID format currently used for
this node. Note that there is no format type 2."
::= { snaNodeEntry 6 }
snaNodeId OBJECT-TYPE
SYNTAX DisplayString (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates the node id for this node instance. The
node id consists of two parts:
The block number is the first three digits of the
node id. These 3 hexadecimal digits identify the
product.
The ID number is the last 5 digits of the node id.
These 5 hexadecimal digits are administratively
defined and combined with the 3-digit block number
form the node id. This node_id is used to identify
the local node and is included in XIDs. A unique
Expires September 06, 1996 [Page 13]
Internet Draft SNANAU MIB March 1996
value is required for connections to SNA subarea.
In some implementations, the value of 'bbb00000'
(where 'bbb' represents a 3-digit block number) is
returned to mean that the ID number is not unique on
this node."
::= { snaNodeEntry 7 }
snaNodeEnablingMethod OBJECT-TYPE
SYNTAX INTEGER {
other(1),
startup(2),
demand(3),
onlyMS(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates how the node is activated for the first
time. The values have the following meanings:
other(1) - not at boot time, LU activation
or by a Management Station;
startup(2) - at SNA services' initialization
time (this is the default);
demand(3) - only when LU is requested by
application;
onlyMS(4) - by a network Management Station only."
::= { snaNodeEntry 8 }
snaNodeLuTermDefault OBJECT-TYPE
SYNTAX INTEGER {
unbind(1),
termself(2),
rshutd(3),
poweroff(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the default method used to deactivate LUs
for this node.
For LU6.2s, 'unbind(1)' is the only valid value.
Expires September 06, 1996 [Page 14]
Internet Draft SNANAU MIB March 1996
unbind(1) - terminate the LU-LU session by sending
an SNA UNBIND request.
termself(2) - terminate the LU-LU session by sending
an SNA TERM-SELF (Terminate Self)
request on the SSCP-LU session. The
SSCP will inform the remote session LU
partner to send an UNBIND request to
terminate the session.
rshutd(3) - terminate the LU-LU session by sending
an SNA RSHUTD (Request ShutDown) request
to the remote session LU partner.
The remote LU will then send an UNBIND
request to terminate the session.
poweroff(4) - terminate the LU-LU session by sending
either an SNA LUSTAT (LU Status) request
on the LU-LU session or an SNA NOTIFY
request on the SSCP-LU session indicating
that the LU has been powered off. Sending
both is also acceptable. The result
should be that the remote session LU
partner will send an UNBIND to terminate
the session.
This object describes the default behavior for this node;
however, it is possible that for a specific LU the behavior
indicated by the snaLuOperTerm object is different."
::= { snaNodeEntry 9 }
snaNodeMaxLu OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the current, maximum number of LUs that
can be activated for this node. For type 2.1 nodes, this
object refers to the number of dependent LUs."
::= { snaNodeEntry 10 }
snaNodeStopMethod OBJECT-TYPE
SYNTAX INTEGER {
other(1),
normal(2),
immed(3),
force(4)
Expires September 06, 1996 [Page 15]
Internet Draft SNANAU MIB March 1996
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the current node shutdown method to be
used by the Agent to stop the node. When the Agent changes the
node's state to 'inactive (1)', the Agent must use the shutdown
method indicated by this object.
The values have the following meaning:
other(1) - proprietary method not listed in this
enumeration
normal(2) - deactivate only when there is no more
activity on this node (i.e., all data
flows have been completed and all
sessions have been terminated).
immed(3) - deactivate immediately regardless of
current activities on this node. Wait
for deactivation responses (from remote
node) before changing the node state to
inactive.
force(4) - deactivate immediately regardless of
current activities on this node. Do not
wait for deactivation responses (from
remote node) before changing the node
state to inactive."
::= { snaNodeEntry 11 }
snaNodeStartTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time of node activation."
::= { snaNodeEntry 12 }
snaNodeLastStateChange OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time of the last state change of the node."
Expires September 06, 1996 [Page 16]
Internet Draft SNANAU MIB March 1996
::= { snaNodeEntry 13 }
snaNodeActFailureReason OBJECT-TYPE
SYNTAX INTEGER {
other(1),
linkFailure(2),
noResources(3),
badConfiguration(4),
internalError(5),
unknown(255)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates the reason for an activation failure. The
value 'other(1)' indicates a reason not listed in the
enumeration. The value 'unknown(255)' indicates that a reason
for the failure cannot be determined.
This object is sent in the trap snaNodeActFailTrap."
::= { snaNodeEntry 14 }
-- ********************************************************************
-- The following object is updated when there is a change to the value
-- of an object in any row of snaNodeTable, or when a row is added to
-- or deleted from the table.
-- ********************************************************************
snaNodeTableLastChange OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time of at the last change made to any object in the
snaNodeTable, including row deletions/additions.
This object can be used to reduce frequent retrievals of the
snaNodeTable by a Management Station. It is expected that a
Management Station will periodically poll this object and
compare its current value with the previous one. A difference
indicates that some node operational information has been
changed. Only then will the Management Station retrieve the
entire table."
Expires September 06, 1996 [Page 17]
Internet Draft SNANAU MIB March 1996
::= { snaNode 4 }
-- ********************************************************************
-- The following table contains information for type 2.0 nodes.
-- ********************************************************************
snaPu20Table OBJECT-TYPE
SYNTAX SEQUENCE OF SnaPu20Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains dynamic parameters that have read-only
access. The entries in this table correspond to the type 2.0
node entries in the snaNodeTable."
::= { snaNode 5 }
snaPu20Entry OBJECT-TYPE
SYNTAX SnaPu20Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The entry contains information related to one type 2.0 node.
Counters represent traffic for all kinds of sessions: LU-LU,
SSCP-PU, and SSCP-LU."
INDEX { snaPu20Name }
::= { snaPu20Table 1 }
SnaPu20Entry ::= SEQUENCE {
snaPu20Name DisplayString,
snaPu20SentBytes Counter32,
snaPu20ReceivedBytes Counter32,
snaPu20SentPius Counter32,
snaPu20ReceivedPius Counter32,
snaPu20SentNegRsps Counter32,
snaPu20ReceivedNegRsps Counter32,
snaPu20ActLus Gauge32,
snaPu20InActLus Gauge32,
snaPu20BindLus Gauge32,
snaPu20HostSscpId OCTET STRING,
snaPu20HostDescription DisplayString,
snaPu20SscpName OCTET STRING,
snaPu20PuName OCTET STRING
Expires September 06, 1996 [Page 18]
Internet Draft SNANAU MIB March 1996
}
snaPu20Name OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locally defined name of the type 2.0 node."
::= { snaPu20Entry 1 }
snaPu20SentBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bytes sent by this node."
::= { snaPu20Entry 2 }
snaPu20ReceivedBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bytes received by this node."
::= { snaPu20Entry 3 }
snaPu20SentPius OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PIUs sent by this node."
::= { snaPu20Entry 4 }
snaPu20ReceivedPius OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PIUs received by this node."
::= { snaPu20Entry 5 }
Expires September 06, 1996 [Page 19]
Internet Draft SNANAU MIB March 1996
snaPu20SentNegRsps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of negative responses sent by this node."
::= { snaPu20Entry 6 }
snaPu20ReceivedNegRsps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of negative responses received by this node."
::= { snaPu20Entry 7 }
snaPu20ActLus OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LUs on this PU that have received and responded
to ACTLU from the host."
::= { snaPu20Entry 8 }
snaPu20InActLus OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LUs on this PU that have not received an ACTLU
from the host. This is possible if the number of configured
LUs exceeds that on the host."
::= { snaPu20Entry 9 }
snaPu20BindLus OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of LUs on this PU that have received and
acknowledged a BIND request from the host."
Expires September 06, 1996 [Page 20]
Internet Draft SNANAU MIB March 1996
::= { snaPu20Entry 10 }
snaPu20HostSscpId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the current SSCP Id associated with the
node. It corresponds to bytes 3-8 of ACTPU."
::= { snaPu20Entry 11 }
snaPu20HostDescription OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the remote host associated with this
node. Since SSCP Id's may not be unique across hosts, the host
description is required to uniquely identify the SSCP.
If the remote host is unknown, then the value is the null
string."
::= { snaPu20Entry 12 }
snaPu20SscpName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0 | 3..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the SSCP that activated this 2.0 node. If an
ACTPU has not been received, a zero-length string is returned."
::= { snaPu20Entry 13 }
snaPu20PuName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name for this node received from the SSCP. If an ACTPU
has not been received, a zero-length string is returned."
::= { snaPu20Entry 14 }
Expires September 06, 1996 [Page 21]
Internet Draft SNANAU MIB March 1996
-- ********************************************************************
-- The following table associates an SNA node with its link stations.
-- It represents configured information.
-- ********************************************************************
snaNodeLinkAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaNodeLinkAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table associates an SNA node with its link stations, and
contains references to link-specific tables. If a node is
configured for multiple links, then the node will have multiple
entries in this table."
::= { snaNode 6 }
snaNodeLinkAdminEntry OBJECT-TYPE
SYNTAX SnaNodeLinkAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains configuration information associating
an SNA node with one of its link stations."
INDEX { snaNodeLinkAdminNodeName,
snaNodeLinkAdminLsName }
::= { snaNodeLinkAdminTable 1 }
SnaNodeLinkAdminEntry ::= SEQUENCE {
snaNodeLinkAdminNodeName DisplayString,
snaNodeLinkAdminLsName DisplayString,
snaNodeLinkAdminSpecific RowPointer,
snaNodeLinkAdminMaxPiu Integer32
}
snaNodeLinkAdminNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Locally-defined name of the node. In a type 2.1 node, this is
a fully qualified name, meaning that the node name is preceded
by the NetId (if present) with a period as the delimiter.
Expires September 06, 1996 [Page 22]
Internet Draft SNANAU MIB March 1996
If this object has the same value as snaNodeName, then the two
entries being indexed apply to the same SNA node."
::= { snaNodeLinkAdminEntry 1 }
snaNodeLinkAdminLsName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..10))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Administratively assigned name for the link station."
::= { snaNodeLinkAdminEntry 2 }
snaNodeLinkAdminSpecific OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value points to a row in a table containing configuration
information for the link instance associated with this node and
link station. It may, for example, point to a row in the
sdlcLSAdminTable defined in the SNA DLC MIB module."
::= { snaNodeLinkAdminEntry 3 }
snaNodeLinkAdminMaxPiu OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the maximum number of octets that can be
exchanged in one Path Information Unit (PIU) by this node
through this link station. This is a configured value, which
the node will use the next time this link is established."
::= { snaNodeLinkAdminEntry 4 }
-- ********************************************************************
-- The following object is updated when there is a change to the value
-- of any object in the snaNodeLinkAdminTable.
-- ********************************************************************
snaNodeLinkAdminTableLastChg OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
Expires September 06, 1996 [Page 23]
Internet Draft SNANAU MIB March 1996
STATUS current
DESCRIPTION
"The time of the last change made to any object in the
snaNodeLinkAdminTable, including row deletions/additions.
This object can be used to reduce frequent retrievals of the
snaNodeLinkAdminTable by a Management Station. It is expected
that a Management Station will periodically poll this object
and compare its current value with the previous one. A
difference indicates that some node configuration information
has been changed. Only then will the Management Station
retrieve the entire table."
::= { snaNode 7 }
-- ********************************************************************
-- The following table associates an SNA node with its link stations.
-- It represents current operational information.
-- ********************************************************************
snaNodeLinkOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaNodeLinkOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table associates an SNA node with its link stations, and
contains references to link-specific tables. If a node has
multiple links, then the node will have multiple entries in
this table."
::= { snaNode 8 }
snaNodeLinkOperEntry OBJECT-TYPE
SYNTAX SnaNodeLinkOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains operational information associating an SNA
node with one of its link stations."
INDEX { snaNodeLinkOperNodeName,
snaNodeLinkOperLsName }
::= { snaNodeLinkOperTable 1 }
SnaNodeLinkOperEntry ::= SEQUENCE {
Expires September 06, 1996 [Page 24]
Internet Draft SNANAU MIB March 1996
snaNodeLinkOperNodeName DisplayString,
snaNodeLinkOperLsName DisplayString,
snaNodeLinkOperSpecific RowPointer,
snaNodeLinkOperMaxPiu Integer32
}
snaNodeLinkOperNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Locally-defined name of the node. In a type 2.1 node, this is
a fully qualified name, meaning that the node name is preceded
by the NetId (if present) with a period as the delimiter.
If this object has the same value as snaNodeName, then the two
entries being indexed apply to the same SNA node."
::= { snaNodeLinkOperEntry 1 }
snaNodeLinkOperLsName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..10))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Administratively assigned name for the link station."
::= { snaNodeLinkOperEntry 2 }
snaNodeLinkOperSpecific OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value points to a row in a table containing operational
information for the link instance associated with this node and
link station. It may, for example, point to a row in the
sdlcLSOperTable defined in the SNA DLC MIB module."
::= { snaNodeLinkOperEntry 3 }
snaNodeLinkOperMaxPiu OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires September 06, 1996 [Page 25]
Internet Draft SNANAU MIB March 1996
"This value identifies the maximum number of octets that can be
exchanged in one Path Information Unit (PIU) by this node
through this link station. This is the current operational
value."
::= { snaNodeLinkOperEntry 4 }
-- ********************************************************************
-- The following object is updated when there is a change to the value
-- of any object in the snaNodeLinkOperTable.
-- ********************************************************************
snaNodeLinkOperTableLastChg OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time of the last change made to any object in the
snaNodeLinkOperTable, including row deletions/additions.
This object can be used to reduce frequent retrievals of the
snaNodeLinkOperTable by a Management Station. It is expected
that a Management Station will periodically poll this object
and compare its current value with the previous one. A
difference indicates that some node operational information has
been changed. Only then will the Management Station retrieve
the entire table."
::= { snaNode 9 }
-- ********************************************************************
-- Traps
-- ********************************************************************
snaNodeTraps OBJECT IDENTIFIER ::= { snaNode 10 }
snaNodeStateChangeTrap NOTIFICATION-TYPE
OBJECTS { snaNodeName,
snaNodeOperState }
STATUS current
DESCRIPTION
"This trap indicates that the operational state (i.e., the
value of the snaNodeOperState object) of a node has changed.
The following variables are returned:
Expires September 06, 1996 [Page 26]
Internet Draft SNANAU MIB March 1996
snaNodeName - name of the node being reported upon
snaNodeOperState - state of the node after the change."
::= { snaNodeTraps 1 }
snaNodeActFailTrap NOTIFICATION-TYPE
OBJECTS { snaNodeName,
snaNodeOperState,
snaNodeActFailureReason }
STATUS current
DESCRIPTION
"This trap indicates a node activation failure. The value of
snaNodeOperState indicates the state of the node after the
activation attempt. The value of snaNodeActFailureReason
indicates the reason for the failure."
::= { snaNodeTraps 2 }
-- ********************************************************************
-- snaLu group
--
-- This group contains Managed Objects related to all dependent LUs,
-- plus some specific objects for LUs of type 0, 1, 2, 3.
--
-- An implementation having both dependent and independent LU 6.2s, or
-- one having only independent LU 6.2s, reports on these LUs via the
-- APPC MIB. An implementation having only dependent LU 6.2s reports on
-- them via this MIB.
-- ********************************************************************
-- ********************************************************************
-- snaLuAdminTable
-- Objects in this table contain default or expected configuration
-- values for local dependent LUs of types 0, 1, 2, 3, 4, 6.2, and 7.
-- ********************************************************************
snaLuAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaLuAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains LU configuration information."
::= { snaLu 1 }
Expires September 06, 1996 [Page 27]
Internet Draft SNANAU MIB March 1996
snaLuAdminEntry OBJECT-TYPE
SYNTAX SnaLuAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Contains configuration variables for an LU."
INDEX { snaLuAdminNodeName,
snaLuAdminLuName }
::= { snaLuAdminTable 1 }
SnaLuAdminEntry ::= SEQUENCE {
snaLuAdminNodeName DisplayString,
snaLuAdminLuName DisplayString,
snaLuAdminUserLuName DisplayString,
snaLuAdminType INTEGER,
snaLuAdminLocalAddress OCTET STRING,
snaLuAdminDisplayModel INTEGER,
snaLuAdminTerm INTEGER
}
snaLuAdminNodeName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value indicates the locally-defined name of the node
through which the LU is to be activated. In a type 2.1 node,
this is a fully qualified name, meaning that the node name is
preceded by the NetId (if present) with a period as the
delimiter.
If this object has the same value as snaNodeName, then the two
entries being indexed apply to the same SNA node."
::= { snaLuAdminEntry 1 }
snaLuAdminLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the locally-defined SNA LU name used in
exchange of SNA data."
Expires September 06, 1996 [Page 28]
Internet Draft SNANAU MIB March 1996
::= { snaLuAdminEntry 2 }
snaLuAdminUserLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..48))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the user configurable name for this LU.
If a name is not assigned to the LU, then this object contains
a zero length string."
::= { snaLuAdminEntry 3 }
snaLuAdminType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
lu0(2),
lu1(3),
lu2(4),
lu3(5),
lu4(6),
lu62(7), -- dependent only
lu7(8),
unknown(255)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the LU type."
::= { snaLuAdminEntry 4 }
snaLuAdminLocalAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local address for this LU is a byte with a value ranging
from 1 to 254."
::= { snaLuAdminEntry 5 }
snaLuAdminDisplayModel OBJECT-TYPE
SYNTAX INTEGER {
invalid(1),
model2A(2),
Expires September 06, 1996 [Page 29]
Internet Draft SNANAU MIB March 1996
model2B(3),
model3A(4),
model3B(5),
model4A(6),
model4B(7),
model5A(8),
model5B(9),
dynamic(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object identifies the model type and screen
size of the terminal connected to the host. This is only valid
for LU Type 2. The values have the following meaning:
model2A(2) - Model 2 (24 rows x 80 columns) with base
attributes
model2B(3) - Model 2 (24 rows x 80 columns) with extended
attributes
model3A(4) - Model 3 (32 rows x 80 columns) with base
attributes
model3B(5) - Model 3 (32 rows x 80 columns) with extended
attributes
model4A(6) - Model 4 (43 rows x 80 columns) with base
attributes
model4B(7) - Model 4 (43 rows x 80 columns) with extended
attributes
model5A(8) - Model 5 (27 rows x 132 columns) with base
attributes
model5B(9) - Model 5 (27 rows x 132 columns) with extended
attributes
dynamic(10)- Screen size determine with BIND and Read
Partition Query.
In case this LU is not Type 2, then this object contains the
invalid(1) value."
::= { snaLuAdminEntry 6 }
snaLuAdminTerm OBJECT-TYPE
SYNTAX INTEGER {
unbind(1),
termself(2),
rshutd(3),
poweroff(4)
Expires September 06, 1996 [Page 30]
Internet Draft SNANAU MIB March 1996
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the desired method for deactivation of
this LU. This value overrides the default method
(snaNodeLuTermDefault) for this node.
For LU6.2s, 'unbind(1)' is the only valid value.
unbind(1) - terminate the LU-LU session by sending
an SNA UNBIND request.
termself(2) - terminate the LU-LU session by sending
an SNA TERM-SELF (Terminate Self)
request on the SSCP-LU session. The
SSCP will inform the remote session LU
partner to send an UNBIND request to
terminate the session.
rshutd(3) - terminate the LU-LU session by sending
an SNA RSHUTD (Request ShutDown) request
to the remote session LU partner.
The remote LU will then send an UNBIND
request to terminate the session.
poweroff(4) - terminate the LU-LU session by sending
either an SNA LUSTAT (LU Status) request
on the LU-LU session or an SNA NOTIFY
request on the SSCP-LU session indicating
that the LU has been powered off. Sending
both is also acceptable. The result
should be that the remote session LU
partner will send an UNBIND to terminate
the session."
::= { snaLuAdminEntry 7 }
-- ********************************************************************
-- snaLuOperTable
-- Objects in this table contain current operational values, such as
-- state values or negotiated parameters, for local dependent LUs of
-- types 0, 1, 2, 3, 4, 6.2, and 7.
-- ********************************************************************
snaLuOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaLuOperEntry
MAX-ACCESS not-accessible
Expires September 06, 1996 [Page 31]
Internet Draft SNANAU MIB March 1996
STATUS current
DESCRIPTION
"This table contains dynamic run-time information and control
variables relating to LUs. Only objects which are common to
all types of LUs are included in this table."
::= { snaLu 2 }
snaLuOperEntry OBJECT-TYPE
SYNTAX SnaLuOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Contains objects reflecting current information for an LU.
Each entry is created by the Agent. All entries have read-only
access."
INDEX { snaLuOperNodeName,
snaLuOperLuName }
::= { snaLuOperTable 1 }
SnaLuOperEntry ::= SEQUENCE {
snaLuOperNodeName DisplayString,
snaLuOperLuName DisplayString,
snaLuOperUserLuName DisplayString,
snaLuOperSscpSuppliedName DisplayString,
snaLuOperType INTEGER,
snaLuOperLocalAddress OCTET STRING,
snaLuOperDisplayModel INTEGER,
snaLuOperTerm INTEGER,
snaLuOperState INTEGER
}
snaLuOperNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value indicates the locally-defined name of the node
through which the LU was activated. In a type 2.1 node, this
is a fully qualified name, meaning that the node name is
preceded by the NetId (if present) with a period as the
delimiter.
If this object has the same value as snaNodeName, then the two
Expires September 06, 1996 [Page 32]
Internet Draft SNANAU MIB March 1996
entries being indexed apply to the same SNA node."
::= { snaLuOperEntry 1 }
snaLuOperLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the locally-defined SNA LU name used in
exchanging SNA data.
If this object has the same value as snaLuAdminLuName, then the
two entries being indexed apply to the same LU."
::= { snaLuOperEntry 2 }
snaLuOperUserLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..48))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"User configurable name for this LU. If a name is not
assigned, then this object contains a zero-length string."
::= { snaLuOperEntry 3 }
snaLuOperSscpSuppliedName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the SNA name of the LU. This name is
supplied to a dependent LU by the SSCP that activated it. If a
value was not supplied, a zero-length string is returned."
::= { snaLuOperEntry 4 }
snaLuOperType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
lu0(2),
lu1(3),
lu2(4),
lu3(5),
lu4(6),
Expires September 06, 1996 [Page 33]
Internet Draft SNANAU MIB March 1996
lu62(7),
lu7(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the current LU type."
::= { snaLuOperEntry 5 }
snaLuOperLocalAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local address for this LU is a byte with a value ranging
from 1 to 254."
::= { snaLuOperEntry 6 }
snaLuOperDisplayModel OBJECT-TYPE
SYNTAX INTEGER {
invalid(1),
model2A(2),
model2B(3),
model3A(4),
model3B(5),
model4A(6),
model4B(7),
model5A(8),
model5B(9),
dynamic(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object identifies the model type and screen
size of the terminal connected to the host. This is only valid
for LU Type 2. The values have the following meaning:
model2A(2) - Model 2 (24 rows x 80 columns) with base
attributes
model2B(3) - Model 2 (24 rows x 80 columns) with extended
attributes
model3A(4) - Model 3 (32 rows x 80 columns) with base
attributes
Expires September 06, 1996 [Page 34]
Internet Draft SNANAU MIB March 1996
model3B(5) - Model 3 (32 rows x 80 columns) with extended
attributes
model4A(6) - Model 4 (43 rows x 80 columns) with base
attributes
model4B(7) - Model 4 (43 rows x 80 columns) with extended
attributes
model5A(8) - Model 5 (27 rows x 132 columns) with base
attributes
model5B(9) - Model 5 (27 rows x 132 columns) with extended
attributes
dynamic(10)- Screen size determine with BIND and Read
Partition Query.
In case this LU is not Type 2, then this object contains the
invalid(1) value."
::= { snaLuOperEntry 7 }
snaLuOperTerm OBJECT-TYPE
SYNTAX INTEGER {
unbind(1),
termself(2),
rshutd(3),
poweroff(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the current method for deactivation of
this LU. This value overrides the default method
(snaNodeLuTermDefault) for this node.
For LU6.2s, 'unbind(1)' is the only valid value.
unbind(1) - terminate the LU-LU session by sending
an SNA UNBIND request.
termself(2) - terminate the LU-LU session by sending
an SNA TERM-SELF (Terminate Self)
request on the SSCP-LU session. The
SSCP will inform the remote session LU
partner to send an UNBIND request to
terminate the session.
rshutd(3) - terminate the LU-LU session by sending
an SNA RSHUTD (Request ShutDown) request
to the remote session LU partner.
The remote LU will then send an UNBIND
Expires September 06, 1996 [Page 35]
Internet Draft SNANAU MIB March 1996
request to terminate the session.
poweroff(4) - terminate the LU-LU session by sending
either an SNA LUSTAT (LU Status) request
on the LU-LU session or an SNA NOTIFY
request on the SSCP-LU session indicating
that the LU has been powered off. Sending
both is also acceptable. The result
should be that the remote session LU
partner will send an UNBIND to terminate
the session."
::= { snaLuOperEntry 8 }
snaLuOperState OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
active(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the current operational state of this LU.
The values indicate the following:
inactive(1) - LU didn't receive an ACTLU, or it received a
DACTLU, or it received an ACTLU and returned a
negative response
active(2) - LU received an ACTLU and returned a positive
response."
::= { snaLuOperEntry 9 }
-- ********************************************************************
-- The following table contains information for active LU-LU sessions.
-- ********************************************************************
snaLuActSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaLuActSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains objects that describe the operational
state of LU-LU sessions. Only objects common to all types of
LUs are included in this table.
Expires September 06, 1996 [Page 36]
Internet Draft SNANAU MIB March 1996
When a session's snaLuActSessOperState value changes to
'pendingBind(2)', then the corresponding entry in this table is
created by the Agent.
When a session's snaLuActSessOperState value changes to
'unbound(1)', then the entry for the session is removed from
this table by the Agent."
::= { snaLu 3 }
snaLuActSessEntry OBJECT-TYPE
SYNTAX SnaLuActSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry contains dynamic parameters for an LU-LU session.
The indices identify the node, local LU, and remote LU for this
session."
INDEX { snaLuActSessNodeName,
snaLuActSessLocLuName,
snaLuActSessIndex }
::= { snaLuActSessTable 1 }
SnaLuActSessEntry ::= SEQUENCE {
snaLuActSessNodeName DisplayString,
snaLuActSessLocLuName DisplayString,
snaLuActSessIndex Integer32,
snaLuActSessOperState INTEGER,
snaLuActSessParLuIndex RowPointer,
snaLuActSessLocalApplName DisplayString,
snaLuActSessParLuName DisplayString,
snaLuActSessMaxSndRuSize INTEGER,
snaLuActSessMaxRcvRuSize INTEGER,
snaLuActSessSndPacingSize INTEGER,
snaLuActSessRcvPacingSize INTEGER,
snaLuActSessUpTime TimeTicks,
snaLuActSessLinkIndex RowPointer
}
snaLuActSessNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value indicates the locally-defined name of the node
Expires September 06, 1996 [Page 37]
Internet Draft SNANAU MIB March 1996
through which the LU for this session was activated. In a type
2.1 node, this is a fully qualified name, meaning that the node
name is preceded by the NetId (if present) with a period as the
delimiter.
If this object has the same value as snaNodeName, then the two
entries being indexed apply to the same SNA node."
::= { snaLuActSessEntry 1 }
snaLuActSessLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the locally-defined SNA LU name for the
session's local LU.
If this object has the same value as snaLuAdminLuName, then the
two entries being indexed apply to the same LU."
::= { snaLuActSessEntry 2 }
snaLuActSessIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the unique index of the session. It is
recommended that an Agent should not reuse the index of a
deactivated session for a significant period of time (e.g., one
week)."
::= { snaLuActSessEntry 3 }
snaLuActSessOperState OBJECT-TYPE
SYNTAX INTEGER {
unbound(1),
pendingBind(2),
bound(3),
pendingUnbind(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value indicates the current operational state of the
Expires September 06, 1996 [Page 38]
Internet Draft SNANAU MIB March 1996
session.
'unbound(1)' - session has been unbound; when a
session enters this state, the Agent
removes its entry from this table
'pendingBind(2)' - waiting for a BIND from the host; when
a session enters this state, the Agent
creates an entry for it in this table
'bound(3)' - session has been successfully bound.
'pendingUnbind(4)' - session is in this state between the
time when an UNBIND is sent and that
when the rsp(UNBIND) is received.
Session deactivation:
If a session is in the operational state 'bound(3)' then
setting the value of this object to 'unbound(1)' will
initiate the session shutdown.
If a session is in the operational state 'pendingBind(2)'
then setting the value of this object to 'unbound(1)' will
initiate the session shutdown.
If a session is in the operational state 'pendingUnbind(4)'
for an abnormally long period of time (e.g., three minutes)
then setting the value of this object to 'unbound(1)' will
change the session operational state to 'unbound(1)'."
::= { snaLuActSessEntry 4 }
snaLuActSessParLuIndex OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value may be used to identify information about the
session partner LU in a table of information about remote LUs.
Such a table is not defined in this document.
If a table of remote LU information is not implemented, or if
the table is implemented but it does not contain information
about the partner LU for a particular session, then this object
shall have the value zeroDotZero defined in SNMPv2-SMI."
Expires September 06, 1996 [Page 39]
Internet Draft SNANAU MIB March 1996
::= { snaLuActSessEntry 5 }
snaLuActSessLocalApplName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..48))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the local application using this LU. If the local
application is unknown, then this object contains a zero-length
string."
::= { snaLuActSessEntry 6 }
snaLuActSessParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the partner LU for the session. If the partner's
LU name is unknown, then this object contains a zero-length
string."
::= { snaLuActSessEntry 7 }
snaLuActSessMaxSndRuSize OBJECT-TYPE
SYNTAX INTEGER (1..8192)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum RU size used on this session for sending RUs."
::= { snaLuActSessEntry 8 }
snaLuActSessMaxRcvRuSize OBJECT-TYPE
SYNTAX INTEGER (1..8192)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum RU size used on this session for receiving RUs."
::= { snaLuActSessEntry 9 }
snaLuActSessSndPacingSize OBJECT-TYPE
SYNTAX INTEGER (1..63)
MAX-ACCESS read-only
Expires September 06, 1996 [Page 40]
Internet Draft SNANAU MIB March 1996
STATUS current
DESCRIPTION
"The size of the send pacing window on this session."
::= { snaLuActSessEntry 10 }
snaLuActSessRcvPacingSize OBJECT-TYPE
SYNTAX INTEGER (1..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the receive pacing window on this session."
::= { snaLuActSessEntry 11 }
snaLuActSessUpTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time the session has been active, measured in
hundredths of a second."
::= { snaLuActSessEntry 12 }
snaLuActSessLinkIndex OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the link over which the session passes.
It is an index into snaNodeLinkAdminTable. If the index value
is not known, this object shall have the value zeroDotZero
defined in SNMPv2-SMI."
::= { snaLuActSessEntry 13 }
-- *********************************************************************
-- SNA LU Historical Session Table
-- ---------------------------------------------------------------------
-- This table contains historical information about LU-LU sessions that
-- terminated abnormally. It is an implementation choice how long to
-- retain information on a given session.
-- *********************************************************************
Expires September 06, 1996 [Page 41]
Internet Draft SNANAU MIB March 1996
snaLuHistSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaLuHistSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of historical information about LU-LU sessions that
terminated abnormally. It is an implementation choice how long
to retain information about a given session."
::= { snaLu 4 }
snaLuHistSessEntry OBJECT-TYPE
SYNTAX SnaLuHistSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of SNA LU Session History Table. This table is indexed
by an integer which is continuously incremented until it
eventually wraps."
INDEX
{ snaLuHistSessIndex }
::= { snaLuHistSessTable 1 }
SnaLuHistSessEntry ::= SEQUENCE {
snaLuHistSessIndex INTEGER,
snaLuHistSessNodeName DisplayString,
snaLuHistSessLocLuName DisplayString,
snaLuHistSessParLuName DisplayString,
snaLuHistSessTime DateAndTime,
snaLuHistSessSenseData SnaSenseData,
snaLuHistSessTerminationRu INTEGER,
snaLuHistSessUnbindType OCTET STRING
}
snaLuHistSessIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table index. The value of the index begins at zero
and is incremented up to a maximum value of 2**31-1
(2,147,483,647) before wrapping."
::= { snaLuHistSessEntry 1 }
Expires September 06, 1996 [Page 42]
Internet Draft SNANAU MIB March 1996
snaLuHistSessNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates the locally-defined name of the node
through which the LU for this session was activated. In a type
2.1 node, this is a fully qualified name, meaning that the node
name is preceded by the NetId (if present) with a period as the
delimiter.
If this object has the same value as snaNodeName, then the two
entries being indexed apply to the same SNA node."
::= { snaLuHistSessEntry 2 }
snaLuHistSessLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the locally-defined SNA LU name for the
session's local LU.
If this object has the same value as snaLuAdminLuName, then the
two entries being indexed apply to the same LU."
::= { snaLuHistSessEntry 3 }
snaLuHistSessParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the partner LU for the session. If the partner's
LU name is unknown, then this object contains a zero-length
string."
::= { snaLuHistSessEntry 4 }
snaLuHistSessTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time at which the session was either terminated or
Expires September 06, 1996 [Page 43]
Internet Draft SNANAU MIB March 1996
failed to be established."
::= { snaLuHistSessEntry 5 }
snaLuHistSessSenseData OBJECT-TYPE
SYNTAX SnaSenseData
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the sense data when there is a BIND
failure. It is taken from the negative BIND response or UNBIND
request."
::= { snaLuHistSessEntry 6 }
snaLuHistSessTerminationRu OBJECT-TYPE
SYNTAX INTEGER {
other(1),
bindFailure(2),
unbind(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the SNA RU that terminated the session."
::= { snaLuHistSessEntry 7 }
snaLuHistSessUnbindType OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the session was terminated by an UNBIND, then this object
contains the UNBIND type value (byte 1 of the UNBIND RU);
otherwise the string is null."
::= { snaLuHistSessEntry 8 }
-- ********************************************************************
-- The following group covers statistics collection for LU-Lu sessions.
-- ********************************************************************
snaLuSessStats OBJECT IDENTIFIER ::= {snaLu 5 }
snaLuSessCntrlOperStat OBJECT-TYPE
Expires September 06, 1996 [Page 44]
Internet Draft SNANAU MIB March 1996
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current collection option in effect:
notActive collection of session statistics is not active.
active collection of session statistics is active.
Statistical entries are present in the snaLuSessStatsTable
only when the value of this object is 'active'."
::= { snaLuSessStats 1 }
snaLuSessCntrlAdminStat OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the desired state of statistics collection:
notActive collection of session statistics is not active.
active collection of session statistics is active.
When this object is set to notActive, all of the entries are
removed from the snaLuSessStatsTable."
::= { snaLuSessStats 2 }
-- ********************************************************************
-- The following table contains session statistics for LU-LU sessions.
-- ********************************************************************
snaLuSessStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaLuSessStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains dynamic statistics information relating to
active LU-LU sessions. The entries in this table cannot be
Expires September 06, 1996 [Page 45]
Internet Draft SNANAU MIB March 1996
created by a Management Station."
::= { snaLuSessStats 3 }
snaLuSessStatsEntry OBJECT-TYPE
SYNTAX SnaLuSessStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Contains statistics information for LU-LU sessions. Each
entry is created by the Agent. Objects in this table have
read-only access. Each session from snaLuActSessTable has one
entry in this table."
INDEX { snaLuSessStatsNodeName,
snaLuSessStatsLuName,
snaLuSessStatsParLuName,
snaLuSessStatsSessIndex }
::= { snaLuSessStatsTable 1 }
SnaLuSessStatsEntry ::= SEQUENCE {
snaLuSessStatsNodeName DisplayString,
snaLuSessStatsLuName DisplayString,
snaLuSessStatsParLuName DisplayString,
snaLuSessStatsSessIndex Integer32,
snaLuSessStatsSentFmdBytes Counter32,
snaLuSessStatsSentNonFmdBytes Counter32,
snaLuSessStatsRcvdFmdBytes Counter32,
snaLuSessStatsRcvdNonFmdBytes Counter32,
snaLuSessStatsSentFmdRus Counter32,
snaLuSessStatsSentNonFmdRus Counter32,
snaLuSessStatsRcvdFmdRus Counter32,
snaLuSessStatsRcvdNonFmdRus Counter32,
snaLuSessStatsSentNegRsps Counter32,
snaLuSessStatsRcvdNegRsps Counter32
}
snaLuSessStatsNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Locally-defined name of the node through which the local LU
for this session was activated. In a type 2.1 node, this is a
fully qualified name, meaning that the node name is preceded by
Expires September 06, 1996 [Page 46]
Internet Draft SNANAU MIB March 1996
the NetId (if present) with a period as the delimiter.
If this object has the same value as snaNodeName, then the two
entries being indexed apply to the same SNA node."
::= { snaLuSessStatsEntry 1 }
snaLuSessStatsLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the local LU for the session. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as snaLuOperLuName, then the
two entries being indexed apply to the same resource
(specifically, to the same local LU)."
::= { snaLuSessStatsEntry 2 }
snaLuSessStatsParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the partner LU for the session. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as snaLuActSessParLuName,
then the two entries being indexed apply to the same resource
(specifically, to the same partner LU)."
::= { snaLuSessStatsEntry 3 }
snaLuSessStatsSessIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the index of the session, which is
unique for this LU pair. It is recommended that an Agent not
Expires September 06, 1996 [Page 47]
Internet Draft SNANAU MIB March 1996
reuse the index of a deactivated session for a significant
period of time (e.g., one week).
If this object has the same value as snaLuActSessIndex for the
same LU pair, then the two entries being indexed apply to the
same resource (specifically, to the same session)."
::= { snaLuSessStatsEntry 4 }
snaLuSessStatsSentFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) bytes sent by the
local LU."
::= { snaLuSessStatsEntry 5 }
snaLuSessStatsSentNonFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) bytes
sent by the local LU."
::= { snaLuSessStatsEntry 6 }
snaLuSessStatsRcvdFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) bytes received by
the local LU."
::= { snaLuSessStatsEntry 7 }
snaLuSessStatsRcvdNonFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) bytes
received by the local LU."
Expires September 06, 1996 [Page 48]
Internet Draft SNANAU MIB March 1996
::= { snaLuSessStatsEntry 8 }
snaLuSessStatsSentFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) RUs sent by the
local LU."
::= { snaLuSessStatsEntry 9 }
snaLuSessStatsSentNonFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) RUs sent
by the local LU."
::= { snaLuSessStatsEntry 10 }
snaLuSessStatsRcvdFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) RUs received by
the local LU."
::= { snaLuSessStatsEntry 11 }
snaLuSessStatsRcvdNonFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) RUs
received by the local LU."
::= { snaLuSessStatsEntry 12 }
snaLuSessStatsSentNegRsps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Expires September 06, 1996 [Page 49]
Internet Draft SNANAU MIB March 1996
DESCRIPTION
"The number of negative responses sent by the local LU."
::= { snaLuSessStatsEntry 13 }
snaLuSessStatsRcvdNegRsps OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of negative responses received by the local LU."
::= { snaLuSessStatsEntry 14 }
-- ********************************************************************
-- Traps
-- ********************************************************************
snaLuTraps OBJECT IDENTIFIER ::= { snaLu 6 }
snaLuActSessBindFailTrap NOTIFICATION-TYPE
OBJECTS { snaLuActSessLocalApplName,
snaLuActSessParLuName,
snaLuActSessOperState,
snaLuHistSessSenseData }
STATUS current
DESCRIPTION
"This trap indicates the failure of a BIND. The value of
snaLuActSessLocalApplName indicates the local application name.
The value of snaLuActSessParLuName indicates the partner name.
The value of snaLuActSessOperState indicates the current state
after change. The value of snaLuHistSessSenseData indicates
the failure reason.
The Agent should not generate more than 1 trap of this type per
minute to minimize the level of management traffic on the
network."
::= { snaLuTraps 1 }
-- ********************************************************************
-- snaMgtTools group
--
-- Currently this group contains only one table.
Expires September 06, 1996 [Page 50]
Internet Draft SNANAU MIB March 1996
-- ********************************************************************
-- ********************************************************************
-- The following table contains Response Time Monitoring (RTM)
-- configuration information and statistics for LU Type 2s.
-- RTM supports the capability to measure and report end-user
-- response times for dependent LUs. When the RTM state of an LU
-- is 'on', response times for each LU transaction are monitored.
-- A set of ranges is defined (e.g., Range 1 includes the number of
-- transactions with response times less than 1 second) using the
-- "boundary" definitions (e.g., boundary #2 is defined as 3 seconds).
-- A set of counters (one per range) identifies
-- the number of transactions within each response-time range.
-- ********************************************************************
snaLuRtmTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnaLuRtmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains Response Time Monitoring (RTM) information
relating to an LU (Type 2). Each entry corresponds to an LU 2
entry in snaLuAdminTable."
::= { snaMgtTools 1 }
snaLuRtmEntry OBJECT-TYPE
SYNTAX SnaLuRtmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Contains RTM information for an LU (Type 2). Each entry is
created by the Agent."
INDEX { snaLuRtmPuName,
snaLuRtmLuName }
::= { snaLuRtmTable 1 }
SnaLuRtmEntry ::= SEQUENCE {
snaLuRtmPuName DisplayString,
snaLuRtmLuName DisplayString,
snaLuRtmCorrelator OCTET STRING,
snaLuRtmState INTEGER,
snaLuRtmStateTime DateAndTime,
snaLuRtmDef INTEGER,
Expires September 06, 1996 [Page 51]
Internet Draft SNANAU MIB March 1996
snaLuRtmBoundary1 Integer32,
snaLuRtmBoundary2 Integer32,
snaLuRtmBoundary3 Integer32,
snaLuRtmBoundary4 Integer32,
snaLuRtmCounter1 Counter32,
snaLuRtmCounter2 Counter32,
snaLuRtmCounter3 Counter32,
snaLuRtmCounter4 Counter32,
snaLuRtmOverflows Counter32,
snaLuRtmTotalTime Integer32,
snaLuRtmLastRspTime Integer32
}
snaLuRtmPuName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locally defined name of the type 2.0 node with which this
LU is associated.
If this object has the same value as snaPu20Name, then the two
entries being indexed apply to the same PU."
::= { snaLuRtmEntry 1 }
snaLuRtmLuName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The name of the LU to which the RTM data applies.
If this object has the same value as snaLuAdminLuName, then the
two entries being indexed apply to the same LU."
::= { snaLuRtmEntry 2 }
snaLuRtmCorrelator OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A value that uniquely identifies an LU-LU session. By
examining this value, a Management Station can determine
Expires September 06, 1996 [Page 52]
Internet Draft SNANAU MIB March 1996
whether RTM that it retrieves is for the same session as
data that it had retrieved previously.
This object corresponds to bytes 7-8 of the X'91' RTM MS
subvector."
::= { snaLuRtmEntry 3 }
snaLuRtmState OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates the current RTM state of an LU.
This object corresponds to bytes 5-6, bit 0 of the X'91'
RTM MS subvector."
::= { snaLuRtmEntry 4 }
snaLuRtmStateTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time when the RTM state for this LU last changed."
::= { snaLuRtmEntry 5 }
snaLuRtmDef OBJECT-TYPE
SYNTAX INTEGER {
firstChar(1),
kb(2),
cdeb(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates the mode of measurement for this RTM
request. The values have following meaning:
firstChar(1) - measured from the Attention or Action key
depression to the arrival back at the LU of
Expires September 06, 1996 [Page 53]
Internet Draft SNANAU MIB March 1996
the first character that can alter the
presentation space
kb(2) - measured from the Attention or Action key
depression until the LU is ready to accept
input from the end user
cdeb(3) - measured from the Attention or Action key
depression to the receipt and processing
back at the LU of Change Direction (CD) or
End Bracket (EB)
This object corresponds to byte 2 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 6 }
snaLuRtmBoundary1 OBJECT-TYPE
SYNTAX Integer32
UNITS "tenths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of the first boundary in units
of 1/10th of a second.
This object corresponds to bytes 9-10 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 7 }
snaLuRtmBoundary2 OBJECT-TYPE
SYNTAX Integer32
UNITS "tenths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of the second boundary in units
of 1/10th of a second.
This object corresponds to bytes 11-12 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 8 }
snaLuRtmBoundary3 OBJECT-TYPE
SYNTAX Integer32
UNITS "tenths of a second"
Expires September 06, 1996 [Page 54]
Internet Draft SNANAU MIB March 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of the third boundary in units
of 1/10th of a second.
This object corresponds to bytes 13-14 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 9 }
snaLuRtmBoundary4 OBJECT-TYPE
SYNTAX Integer32
UNITS "tenths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of the fourth boundary in units
of 1/10th of a second.
This object corresponds to bytes 15-16 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 10 }
snaLuRtmCounter1 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of exchanges in the range (0, boundary1).
This object corresponds to bytes p+1 - p+2 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 11 }
snaLuRtmCounter2 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of exchanges in the range (boundary1 + 1, boundary2).
This object corresponds to bytes p+3 - p+4 of the X'93' RTM MS
subvector."
Expires September 06, 1996 [Page 55]
Internet Draft SNANAU MIB March 1996
::= { snaLuRtmEntry 12 }
snaLuRtmCounter3 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of exchanges in the range (boundary2 + 1, boundary3).
This object corresponds to bytes p+5 - p+6 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 13 }
snaLuRtmCounter4 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of exchanges in the range (boundary3 + 1, boundary4).
This object corresponds to bytes p+7 - p+8 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 14 }
snaLuRtmOverflows OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of exchange durations greater than the maximum
boundary specified.
This object corresponds to bytes q+1 - q+2 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 15 }
snaLuRtmTotalTime OBJECT-TYPE
SYNTAX Integer32
UNITS "tenths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total of all individual times for all exchanges measured
Expires September 06, 1996 [Page 56]
Internet Draft SNANAU MIB March 1996
and reported by this table row, including overflows, in units
of 1/10 of a second.
This object corresponds to bytes q+3 - q+6 of the X'93' RTM MS
subvector."
::= { snaLuRtmEntry 16 }
snaLuRtmLastRspTime OBJECT-TYPE
SYNTAX Integer32
UNITS "tenths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value indicates the response time for the last
transaction in units of 1/10th of a second."
::= { snaLuRtmEntry 17 }
-- ********************************************************************
-- Conformance information
-- ********************************************************************
snanauConformance OBJECT IDENTIFIER ::= { snanauMIB 2 }
snanauCompliances OBJECT IDENTIFIER ::= {snanauConformance 1 }
snanauGroups OBJECT IDENTIFIER ::= {snanauConformance 2 }
-- Compliance statements
snanauCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMPv2 entities which
implement the SNANAU MIB." MODULE -- this module
-- Unconditionally mandatory groups
MANDATORY-GROUPS { snaNodeGroup,
snaLuGroup,
snaSessionGroup }
-- Conditionally mandatory groups
GROUP snaPu20Group
DESCRIPTION
"The snaPu20Group is mandatory only for those
entities which implement PU type 2.0"
Expires September 06, 1996 [Page 57]
Internet Draft SNANAU MIB March 1996
GROUP snaMgtToolsRtmGroup
DESCRIPTION
"The snaMgtToolsGroup is mandatory only for those
entities which implement LU type 2 and RTM."
OBJECT snaNodeAdminState
MIN-ACCESS read-only
DESCRIPTION
"An Agent is not required to support node
deactivation via this object."
::= { snanauCompliances 1 }
-- Units of conformance
snaNodeGroup OBJECT-GROUP
OBJECTS { snaNodeAdminState,
snaNodeOperState,
snaNodeSscpSuppliedName,
snaNodeType,
snaNodeXidFormat,
snaNodeId,
snaNodeEnablingMethod,
snaNodeLuTermDefault,
snaNodeMaxLu,
snaNodeStopMethod,
snaNodeStartTime,
snaNodeLastStateChange,
snaNodeActFailureReason,
snaNodeTableLastChange,
snaNodeLinkAdminSpecific,
snaNodeLinkAdminMaxPiu,
snaNodeLinkAdminTableLastChg,
snaNodeLinkOperSpecific,
snaNodeLinkOperMaxPiu,
snaNodeLinkOperTableLastChg }
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation for SNA
nodes."
::= { snanauGroups 1 }
snaLuGroup OBJECT-GROUP
OBJECTS { snaLuAdminUserLuName,
Expires September 06, 1996 [Page 58]
Internet Draft SNANAU MIB March 1996
snaLuAdminType,
snaLuAdminLocalAddress,
snaLuAdminDisplayModel,
snaLuAdminTerm,
snaLuOperUserLuName,
snaLuOperSscpSuppliedName,
snaLuOperType,
snaLuOperLocalAddress,
snaLuOperDisplayModel,
snaLuOperTerm,
snaLuOperState }
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation for
dependent SNA LUs."
::= { snanauGroups 2 }
snaSessionGroup OBJECT-GROUP
OBJECTS { snaLuActSessOperState,
snaLuActSessParLuIndex,
snaLuActSessLocalApplName,
snaLuActSessParLuName,
snaLuActSessMaxSndRuSize,
snaLuActSessMaxRcvRuSize,
snaLuActSessSndPacingSize,
snaLuActSessRcvPacingSize,
snaLuActSessUpTime,
snaLuActSessLinkIndex,
snaLuHistSessNodeName,
snaLuHistSessLocLuName,
snaLuHistSessParLuName,
snaLuHistSessTime,
snaLuHistSessSenseData,
snaLuHistSessTerminationRu,
snaLuHistSessUnbindType,
snaLuSessCntrlOperStat,
snaLuSessCntrlAdminStat,
snaLuSessStatsSentFmdBytes,
snaLuSessStatsSentNonFmdBytes,
snaLuSessStatsRcvdFmdBytes,
snaLuSessStatsRcvdNonFmdBytes,
snaLuSessStatsSentFmdRus,
snaLuSessStatsSentNonFmdRus,
snaLuSessStatsRcvdFmdRus,
snaLuSessStatsRcvdNonFmdRus,
Expires September 06, 1996 [Page 59]
Internet Draft SNANAU MIB March 1996
snaLuSessStatsSentNegRsps,
snaLuSessStatsRcvdNegRsps }
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation for SNA
sessions involving dependent LUs."
::= { snanauGroups 3 }
snaPu20Group OBJECT-GROUP
OBJECTS { snaPu20SentBytes,
snaPu20ReceivedBytes,
snaPu20SentPius,
snaPu20ReceivedPius,
snaPu20SentNegRsps,
snaPu20ReceivedNegRsps,
snaPu20ActLus,
snaPu20InActLus,
snaPu20BindLus,
snaPu20HostSscpId,
snaPu20HostDescription,
snaPu20SscpName,
snaPu20PuName }
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation for type
2.0 nodes."
::= { snanauGroups 4 }
snaMgtToolsRtmGroup OBJECT-GROUP
OBJECTS { snaLuRtmCorrelator,
snaLuRtmState,
snaLuRtmStateTime,
snaLuRtmDef,
snaLuRtmBoundary1,
snaLuRtmBoundary2,
snaLuRtmBoundary3,
snaLuRtmBoundary4,
snaLuRtmCounter1,
snaLuRtmCounter2,
snaLuRtmCounter3,
snaLuRtmCounter4,
snaLuRtmOverflows,
snaLuRtmTotalTime,
snaLuRtmLastRspTime }
Expires September 06, 1996 [Page 60]
Internet Draft SNANAU MIB March 1996
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of RTM
for SNA LU 2.0."
::= { snanauGroups 5 }
-- end of conformance statement
END
Expires September 06, 1996 [Page 61]
Internet Draft SNANAU MIB March 1996
6. Acknowledgments
This MIB module is the product of the SNA NAU MIB Working Group.
7. References
[1] IBM, Systems Network Architecture Technical Overview, GC30-3073-3,
March, 1991.
[2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Structure of Management Information for version 2 of
the Simple Network Management Protocol (SNMPv2)", RFC 1902, January
1996.
[3] McCloghrie, K., and M. Rose, Editors, "Management Information Base
for Network Management of TCP/IP-based internets: MIB-II", STD 17,
RFC 1213, March 1991.
[4] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, May 1990.
[5] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Protocol Operations for version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1905, January 1996.
Expires September 06, 1996 [Page 62]
Internet Draft SNANAU MIB March 1996
8. Security Considerations
Security issues are not discussed in this memo.
9. Authors' Addresses
Zbigniew Kielczewski
Cisco Systems
7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709, USA
Tel: 1 919 472 2326
E-mail: zkielcze@cisco.com
Kitty Shih
Novell
890 Ross Drive
Sunnyvale, CA 94089
Tel: 1 408 747 4305
E-mail: kmshih@novell.com
Bob Moore
IBM Corporation
800 Park Offices Drive
CNMA/664
P.O. Box 12195
Research Triangle Park, NC 27709, USA
Tel: 1 919 254 4436
E-mail: remoore@ralvm6.vnet.ibm.com
Expires September 06, 1996 [Page 63]
Internet Draft SNANAU MIB March 1996
10. Table of Contents
1. Status of this Memo .................................... 1
2. Introduction ........................................... 2
3. The SNMPv2 Network Management Framework ................ 2
4. Overview ............................................... 2
4.1 SNANAU MIB structure .................................. 3
5. Definitions ............................................ 8
6. Acknowledgments ........................................ 62
7. References ............................................. 62
8. Security Considerations ................................ 63
9. Author's Addresses ...................................... 63
Expires September 06, 1996 [Page 64]
