Network Working Group                                         S. Bensley
Internet-Draft                                                 Microsoft
Intended status: Informational                                 L. Eggert
Expires: May 5, 2016                                              NetApp
                                                               D. Thaler
                                                      P. Balasubramanian
                                                               Microsoft
                                                                 G. Judd
                                                          Morgan Stanley
                                                        November 2, 2015


     Datacenter TCP (DCTCP): TCP Congestion Control for Datacenters
                        draft-ietf-tcpm-dctcp-01

Abstract

   This informational memo describes Datacenter TCP (DCTCP), an
   improvement to TCP congestion control for datacenter traffic.  DCTCP
   uses improved Explicit Congestion Notification (ECN) processing to
   estimate the fraction of bytes that encounter congestion, rather than
   simply detecting that some congestion has occurred.  DCTCP then
   scales the TCP congestion window based on this estimate.  This method
   achieves high burst tolerance, low latency, and high throughput with
   shallow-buffered switches.  This memo also discusses deployment
   issues related to the coexistence of DCTCP and conventional TCP, the
   lack of a negotiating mechanism between sender and receiver, and
   presents some possible mitigations.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on May 5, 2016.






Bensley, et al.            Expires May 5, 2016                  [Page 1]


Internet-Draft                    DCTCP                    November 2015


Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  DCTCP Algorithm . . . . . . . . . . . . . . . . . . . . . . .   4
     3.1.  Marking Congestion on the Switches  . . . . . . . . . . .   4
     3.2.  Echoing Congestion Information on the Receiver  . . . . .   4
     3.3.  Processing Congestion Indications on the Sender . . . . .   5
     3.4.  Handling of SYN, SYN-ACK, RST Packets . . . . . . . . . .   7
   4.  Implementation Issues . . . . . . . . . . . . . . . . . . . .   7
   5.  Deployment Issues . . . . . . . . . . . . . . . . . . . . . .   9
   6.  Known Issues  . . . . . . . . . . . . . . . . . . . . . . . .  10
   7.  Implementation Status . . . . . . . . . . . . . . . . . . . .  11
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  11
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  11
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  11
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  12
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  12
     11.2.  Informative References . . . . . . . . . . . . . . . . .  12
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  14

1.  Introduction

   Large datacenters necessarily need many network switches to
   interconnect its many servers.  Therefore, a datacenter can greatly
   reduce its capital expenditure by leveraging low-cost switches.
   However, such low-cost switches tend to have limited queue capacities
   and are thus more susceptible to packet loss due to congestion.

   Network traffic in a datacenter is often a mix of short and long
   flows, where the short flows require low latencies and the long flows
   require high throughputs.  Datacenters also experience incast bursts,
   where many servers send traffic to a single server at the same time.



Bensley, et al.            Expires May 5, 2016                  [Page 2]


Internet-Draft                    DCTCP                    November 2015


   For example, this traffic pattern is a natural consequence of
   MapReduce workload: The worker nodes complete at approximately the
   same time, and all reply to the master node concurrently.

   These factors place some conflicting demands on the queue occupancy
   of a switch:

   o  The queue must be short enough that it does not impose excessive
      latency on short flows.

   o  The queue must be long enough to buffer sufficient data for the
      long flows to saturate the path capacity.

   o  The queue must be short enough to absorb incast bursts without
      excessive packet loss.

   Standard TCP congestion control [RFC5681] relies on packet loss to
   detect congestion.  This does not meet the demands described above.
   First, short flows will start to experience unacceptable latencies
   before packet loss occurs.  Second, by the time TCP congestion
   control kicks in on the senders, most of the incast burst has already
   been dropped.

   [RFC3168] describes a mechanism for using Explicit Congestion
   Notification (ECN) from the switches for early detection of
   congestion, rather than waiting for packet loss to occur.  However,
   this method only detects the presence of congestion, not its extent.
   In the presence of mild congestion, the TCP congestion window is
   reduced too aggressively and this unnecessarily reduces the
   throughput of long flows.

   Datacenter TCP (DCTCP) improves traditional ECN processing by
   estimating the fraction of bytes that encounter congestion, rather
   than simply detecting that some congestion has occurred.  DCTCP then
   scales the TCP congestion window based on this estimate.  This method
   achieves high burst tolerance, low latency, and high throughput with
   shallow-buffered switches.

   It is recommended that DCTCP be deployed in a datacenter environment
   where the endpoints and the switching fabric are under a single
   administrative domain.  This protocol is not meant for uncontrolled
   deployment in the global Internet.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].



Bensley, et al.            Expires May 5, 2016                  [Page 3]


Internet-Draft                    DCTCP                    November 2015


3.  DCTCP Algorithm

   There are three components involved in the DCTCP algorithm:

   o  The switches (or other intermediate devices in the network) detect
      congestion and set the Congestion Encountered (CE) codepoint in
      the IP header.

   o  The receiver echoes the congestion information back to the sender,
      using the ECN-Echo (ECE) flag in the TCP header.

   o  The sender computes a congestion estimate and reacts, by reducing
      the TCP congestion window accordingly (cwnd).

3.1.  Marking Congestion on the Switches

   The switches in a datacenter fabric indicate congestion to the end
   nodes by setting the CE codepoint in the IP header as specified in
   Section 5 of [RFC3168].  For example, the switches may be configured
   with a congestion threshold.  When a packet arrives at a switch and
   its queue length is greater than the congestion threshold, the switch
   sets the CE codepoint in the packet.  For example, Section 3.4 of
   [DCTCP10] suggests threshold marking with a threshold K > (RTT *
   C)/7, where C is the sending rate in packets per second.  However,
   the actual algorithm for marking congestion is an implementation
   detail of the switch and will generally not be known to the sender
   and receiver.  Therefore, sender and receiver MUST NOT assume that a
   particular marking algorithm is implemented by the switching fabric.

3.2.  Echoing Congestion Information on the Receiver

   According to Section 6.1.3 of [RFC3168], the receiver sets the ECE
   flag if any of the packets being acknowledged had the CE code point
   set.  The receiver then continues to set the ECE flag until it
   receives a packet with the Congestion Window Reduced (CWR) flag set.
   However, the DCTCP algorithm requires more detailed congestion
   information.  In particular, the sender must be able to determine the
   number of bytes sent that encountered congestion.  Thus, the scheme
   described in [RFC3168] does not suffice.

   One possible solution is to ACK every packet and set the ECE flag in
   the ACK if and only if the CE code point was set in the packet being
   acknowledged.  However, this prevents the use of delayed ACKs, which
   are an important performance optimization in datacenters.

   Instead, DCTCP introduces a new Boolean TCP state variable, "DCTCP
   Congestion Encountered" (DCTCP.CE), which is initialized to false and
   stored in the Transmission Control Block (TCB).  When sending an ACK,



Bensley, et al.            Expires May 5, 2016                  [Page 4]


Internet-Draft                    DCTCP                    November 2015


   the ECE flag MUST be set if and only if DCTCP.CE is true.  When
   receiving packets, the CE codepoint MUST be processed as follows:

   1.  If the CE codepoint is set and DCTCP.CE is false, send an ACK for
       any previously unacknowledged packets and set DCTCP.CE to true.

   2.  If the CE codepoint is not set and DCTCP.CE is true, send an ACK
       for any previously unacknowledged packets and set DCTCP.CE to
       false.

   3.  Otherwise, ignore the CE codepoint.

   The handling of the "Congestion Window Reduced" (CWR) bit is also
   exactly as per [RFC3168] including [RFC3168-ERRATA3639].  That is, on
   receipt of a segment with both the CE and CWR bits set, CWR is
   processed first and then ECE is processed.

                                  Send immediate
                                  ACK with ECE=0
                        .----.    .-------------.     .---.
           Send 1 ACK  /     v    v             |    |     \
            for every |     .------.           .------.     | Send 1 ACK
            m packets |     | CE=0 |           | CE=1 |     | for every
           with ECE=0 |     '------'           '------'     | m packets
                       \     |    |             ^    ^     /  with ECE=1
                        '---'      '------------'    '----'
                                   Send immediate
                                   ACK with ECE=1

   Figure 1: ACK generation state machine.  DCTCP.CE abbreviated as CE.

3.3.  Processing Congestion Indications on the Sender

   The sender estimates the fraction of bytes sent that encountered
   congestion.  The current estimate is stored in a new TCP state
   variable, DCTCP.Alpha, which is initialized to 1 and MUST be updated
   as follows:

      DCTCP.Alpha = DCTCP.Alpha * (1 - g) + g * M

   where

   o  g is the estimation gain, a real number between 0 and 1.  The
      selection of g is left to the implementation.  See Section 4 for
      further considerations.

   o  M is the fraction of bytes sent that encountered congestion during
      the previous observation window, where the observation window is



Bensley, et al.            Expires May 5, 2016                  [Page 5]


Internet-Draft                    DCTCP                    November 2015


      chosen to be approximately the Round Trip Time (RTT).  In
      particular, an observation window ends when all bytes in flight at
      the beginning of the window have been acknowledged.

   In order to update DCTCP.Alpha, the TCP state variables defined in
   [RFC0793] are used, and three additional TCP state variables are
   introduced:

   o  DCTCP.WindowEnd: The TCP sequence number threshold for beginning a
      new observation window; initialized to SND.UNA.

   o  DCTCP.BytesSent: The number of bytes sent during the current
      observation window; initialized to zero.

   o  DCTCP.BytesMarked: The number of bytes sent during the current
      observation window that encountered congestion; initialized to
      zero.

   The congestion estimator on the sender MUST process acceptable ACKs
   as follows:

   1.  Compute the bytes acknowledged (TCP SACK options [RFC2018] are
       ignored):

          BytesAcked = SEG.ACK - SND.UNA

   2.  Update the bytes sent:

          DCTCP.BytesSent += BytesAcked

   3.  If the ECE flag is set, update the bytes marked:

          DCTCP.BytesMarked += BytesAcked

   4.  If the acknowledgment number is less than or equal to
       DCTCP.WindowEnd, stop processing.  Otherwise, the end of the
       observation window has been reached, so proceed to update the
       congestion estimate as follows:

   5.  Compute the congestion level for the current observation window:

          M = DCTCP.BytesMarked / DCTCP.BytesSent

   6.  Update the congestion estimate:

          DCTCP.Alpha = DCTCP.Alpha * (1 - g) + g * M

   7.  Determine the end of the next observation window:



Bensley, et al.            Expires May 5, 2016                  [Page 6]


Internet-Draft                    DCTCP                    November 2015


          DCTCP.WindowEnd = SND.NXT

   8.  Reset the byte counters:

          DCTCP.BytesSent = DCTCP.BytesMarked = 0

   Rather than always halving the congestion window as described in
   [RFC3168], when the sender receives an indication of congestion
   (ECE), the sender MUST update cwnd as follows:

      cwnd = cwnd * (1 - DCTCP.Alpha / 2)

   Thus, when no bytes sent experienced congestion, DCTCP.Alpha equals
   zero, and cwnd is left unchanged.  When all sent bytes experienced
   congestion, DCTCP.Alpha equals one, and cwnd is reduced by half.
   Lower levels of congestion will result in correspondingly smaller
   reductions to cwnd.

   Just as specified in [RFC3168], TCP should not react to congestion
   indications more than once for every window of data.  The setting of
   the "Congestion Window Reduced" (CWR) bit is also exactly as per
   [RFC3168].

3.4.  Handling of SYN, SYN-ACK, RST Packets

   [RFC3168] requires that a compliant TCP MUST NOT set ECT on SYN or
   SYN-ACK packets.  [RFC5562] proposes setting ECT on SYN-ACK packets,
   but maintains the restriction of no ECT on SYN packets.  Both these
   RFCs prohibit ECT in SYN packets due to security concerns regarding
   malicious SYN packets with ECT set.  These RFCs, however, are
   intended for general Internet use, and do not directly apply to a
   controlled datacenter environment.  The switching fabric can drop TCP
   packets that do not have the ECT set in the IP header.  If SYN and
   SYN-ACK packets for DCTCP connections do not have ECT set, they will
   be dropped with high probability.  For DCTCP connections, the sender
   SHOULD set ECT for SYN, SYN-ACK and RST packets.

4.  Implementation Issues

   As noted in Section 3.3, the implementation MUST choose a suitable
   estimation gain.  [DCTCP10] provides a theoretical basis for
   selecting the gain.  However, it may be more practical to use
   experimentation to select a suitable gain for a particular network
   and workload.  The Microsoft implementation of DCTCP in Windows
   Server 2012 uses a fixed estimation gain of 1/16.

   The implementation must also decide when to use DCTCP.  Datacenter
   servers may need to communicate with endpoints outside the



Bensley, et al.            Expires May 5, 2016                  [Page 7]


Internet-Draft                    DCTCP                    November 2015


   datacenter, where DCTCP is unsuitable or unsupported.  Thus, a global
   configuration setting to enable DCTCP will generally not suffice.
   DCTCP provides no mechanism for negotiating its use.  Thus, there is
   additional management and configuration overhead required to ensure
   that DCTCP is not used with non-DCTCP endpoints.

   Potential solutions rely on either configuration or heuristics.
   Heuristics need to allow endpoints to individually enable DCTCP, to
   ensure a DCTCP sender is always paired with a DCTCP receiver.  One
   approach is to enable DCTCP based on the IP address of the remote
   endpoint.  Another approach is to detect connections that transmit
   within the bounds a datacenter.  For example, Microsoft Windows
   Server 2012 (and later versions) supports automatic selection of
   DCTCP if the estimated RTT is less than 10 msec and ECN is
   successfully negotiated, under the assumption that if the RTT is low,
   then the two endpoints are likely in the same datacenter network.

   It is RECOMMENDED that an implementation deal with loss episodes in
   the same way as conventional TCP.  In case of a timeout or fast
   retransmit or any change in delay (for delay based congestion
   control), the cwnd and other state variables like ssthresh must be
   changed in the same way that a conventional TCP would have changed
   them.  It would be useful to implement DCTCP as additional actions on
   top of an existing congestion control algorithm like NewReno.  The
   DCTCP implementation MAY also allow configuration of resetting the
   value of DCTCP.Alpha as part of processing any loss episodes.

   To prevent incast throughput collapse, the minimum RTO (MinRTO) used
   by TCP should be lowered significantly.  The default value of MinRTO
   in Windows is 300 msec, which is much greater than the maximum
   latencies inside a datacenter.  In Microsoft Windows Server 2012 (and
   later), the MinRTO value is configurable, allowing values as low as
   10 msec on a per-subnet or per-port basis (or even globally.)  A
   lower MinRTO value requires a correspondingly lower delayed ACK
   timeout on the receiver.  It is RECOMMENDED that an implementation
   allow configuration of lower timeouts for DCTCP connections.

   In the same vein, it is also RECOMMENDED that an implementation allow
   configuration of restarting the congestion window (cwnd) of idle
   DCTCP connections as described in [RFC5681], since network conditions
   can change rapidly in datacenters.

   [RFC3168] forbids the ECN-marking of pure ACK packets, because of the
   inability of TCP to mitigate ACK-path congestion and protocol-wise
   preferential treatment by routers.  However, dropping pure ACKs -
   rather than ECN marking them - has disadvantages for typical
   datacenter traffic patterns.  Because of the prevalence of bursty
   traffic patterns that feature transient congestion, dropping of ACKs



Bensley, et al.            Expires May 5, 2016                  [Page 8]


Internet-Draft                    DCTCP                    November 2015


   causes subsequent retransmissions.  It is RECOMMENDED that an
   implementation provide a configuration knob that forces ECT to be set
   on pure ACKs.

   The DCTCP.Alpha calculation as per the formula in Section 3.3
   involves fractions.  An efficient kernel implementation MAY scale the
   DCTCP.Alpha value for efficient computation using shift operations.
   For example, if the implementation chooses g as 1/16, multiplications
   of DCTCP.Alpha by g become right-shifts by 4.  A scaling
   implementation SHOULD ensure that DCTCP.Alpha is able to reach zero
   once it falls below the smallest shifted value (16 in the above
   example).  At the other extreme, a scaled update MUST also ensure
   DCTCP.Alpha does not exceed the scaling factor, which would be
   equivalent to greater than 100% congestion.  So, DCTCP.Alpha MUST be
   clamped after an update.

   This results in the following computations replacing steps 5 and 6 in
   Section 3.3, where SCF is the chosen scaling factor (65536 in the
   example) and SHF is the shift factor (4 in the example):

   1.  Compute the congestion level for the current observation window:

          ScaledM = SCF * DCTCP.BytesMarked / DCTCP.BytesSent

   2.  Update the congestion estimate:

          if (DCTCP.Alpha >> SHF) == 0 then DCTCP.Alpha = 0

          DCTCP.Alpha += (ScaledM >> SHF) - (DCTCP.Alpha >> SHF)

          if DCTCP.Alpha > SCF then DCTCP.Alpha = SCF

5.  Deployment Issues

   DCTCP and conventional TCP congestion control do not coexist well in
   the same network.  In DCTCP, the marking threshold is set to a very
   low value to reduce queueing delay, and a relatively small amount of
   congestion will exceed the marking threshold.  During such periods of
   congestion, conventional TCP will suffer packet loss and quickly and
   drastically reduce cwnd.  DCTCP, on the other hand, will use the
   fraction of marked packets to reduce cwnd more gradually.  Thus, the
   rate reduction in DCTCP will be much slower than that of conventional
   TCP, and DCTCP traffic will gain a larger share of the capacity
   compared to conventional TCP traffic traversing the same path.  If
   the traffic in the datacenter is a mix of conventional TCP and DCTCP,
   it is RECOMMENDED that DCTCP traffic be segregated from conventional
   TCP traffic.  [MORGANSTANLEY] describes a deployment that uses the IP




Bensley, et al.            Expires May 5, 2016                  [Page 9]


Internet-Draft                    DCTCP                    November 2015


   DSCP bits to segregate the network such that AQM is applied to DCTCP
   traffic, whereas TCP traffic is managed via drop-tail queueing.

   Today's commodity switches allow configuration of different marking/
   drop profiles for non-TCP and non-IP packets.  Non-TCP and non-IP
   packets should be able to pass through such switches, unless they
   really run out of buffer space.  If the datacenter traffic consists
   of such traffic (including UDP), one possible mitigation would be to
   mark IP packets as ECT even when there is no transport that is
   reacting to the marking.

   Since DCTCP relies on congestion marking by the switches, DCTCP can
   only be deployed in datacenters where the entire network
   infrastructure supports ECN.  The switches may also support
   configuration of the congestion threshold used for marking.  The
   proposed parameterization can be configured with switches that
   implement RED.  [DCTCP10] provides a theoretical basis for selecting
   the congestion threshold, but as with the estimation gain, it may be
   more practical to rely on experimentation or simply to use the
   default configuration of the device.  DCTCP will degrade to loss-
   based congestion control when transiting a congested drop-tail link.

   DCTCP requires changes on both the sender and the receiver, so both
   endpoints must support DCTCP.  Furthermore, DCTCP provides no
   mechanism for negotiating its use, so both endpoints must be
   configured through some out-of-band mechanism to use DCTCP.  A
   variant of DCTCP that can be deployed unilaterally and only requires
   standard ECN behavior has been described in [ODCTCP][BSDCAN], but
   requires additional experimental evaluation.

6.  Known Issues

   DCTCP relies on the sender's ability to reconstruct the stream of CE
   codepoints received by the remote endpoint.  To accomplish this,
   DCTCP avoids using a single ACK packet to acknowledge segments
   received both with and without the CE codepoint set.  However, if one
   or more ACK packets are dropped, it is possible that a subsequent ACK
   will cumulatively acknowledge a mix of CE and non-CE segments.  This
   will, of course, result in a less accurate congestion estimate.
   There are some potential considerations:

   o  Even with an inaccurate congestion estimate, DCTCP may still
      perform better than [RFC3168].

   o  If the estimation gain is small relative to the packet loss rate,
      the estimate may not be too inaccurate.





Bensley, et al.            Expires May 5, 2016                 [Page 10]


Internet-Draft                    DCTCP                    November 2015


   o  If packet loss mostly occurs under heavy congestion, most drops
      will occur during an unbroken string of CE packets, and the
      estimate will be unaffected.

   However, the effect of packet drops on DCTCP under real world
   conditions has not been analyzed.

   DCTCP provides no mechanism for negotiating its use.  The effect of
   using DCTCP with a standard ECN endpoint has been analyzed in
   [ODCTCP][BSDCAN].  Furthermore, it is possible that other
   implementations may also modify [RFC3168] behavior without
   negotiation, causing further interoperability issues.

   Much like standard TCP, DCTCP is biased against flows with longer
   RTTs.  A method for improving the fairness of DCTCP has been proposed
   in [ADCTCP], but requires additional experimental evaluation.

7.  Implementation Status

   This section documents the implementation status of the specification
   in this document, as recommended by [RFC6982].

   This document describes DCTCP as implemented in Microsoft Windows
   Server 2012.  Since publication of the first versions of this
   document, the Linux [LINUX] and FreeBSD [FREEBSD] operating systems
   have also implemented support for DCTCP in a way that is believed to
   follow this document.

8.  Security Considerations

   DCTCP enhances ECN and thus inherits the security considerations
   discussed in [RFC3168].  The processing changes introduced by DCTCP
   do not exacerbate these considerations or introduce new ones.  In
   particular, with either algorithm, the network infrastructure or the
   remote endpoint can falsely report congestion and thus cause the
   sender to reduce cwnd.  However, this is no worse than what can be
   achieved by simply dropping packets.

9.  IANA Considerations

   This document has no actions for IANA.

10.  Acknowledgements

   The DCTCP algorithm was originally proposed and analyzed in [DCTCP10]
   by Mohammad Alizadeh, Albert Greenberg, Dave Maltz, Jitu Padhye,
   Parveen Patel, Balaji Prabhakar, Sudipta Sengupta, and Murari
   Sridharan.



Bensley, et al.            Expires May 5, 2016                 [Page 11]


Internet-Draft                    DCTCP                    November 2015


   We would like to thank Andrew Shewmaker for identifying the problem
   of clamping DCTCP.Alpha and proposing a solution for it.

   Lars Eggert has received funding from the European Union's Horizon
   2020 research and innovation program 2014-2018 under grant agreement
   No. 644866 ("SSICLOPS").  This document reflects only the authors'
   views and the European Commission is not responsible for any use that
   may be made of the information it contains.

11.  References

11.1.  Normative References

   [RFC0793]  Postel, J., "Transmission Control Protocol", STD 7,
              RFC 793, DOI 10.17487/RFC0793, September 1981,
              <http://www.rfc-editor.org/info/rfc793>.

   [RFC2018]  Mathis, M., Mahdavi, J., Floyd, S., and A. Romanow, "TCP
              Selective Acknowledgment Options", RFC 2018,
              DOI 10.17487/RFC2018, October 1996,
              <http://www.rfc-editor.org/info/rfc2018>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC3168]  Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
              of Explicit Congestion Notification (ECN) to IP",
              RFC 3168, DOI 10.17487/RFC3168, September 2001,
              <http://www.rfc-editor.org/info/rfc3168>.

11.2.  Informative References

   [RFC5681]  Allman, M., Paxson, V., and E. Blanton, "TCP Congestion
              Control", RFC 5681, DOI 10.17487/RFC5681, September 2009,
              <http://www.rfc-editor.org/info/rfc5681>.

   [RFC5562]  Kuzmanovic, A., Mondal, A., Floyd, S., and K.
              Ramakrishnan, "Adding Explicit Congestion Notification
              (ECN) Capability to TCP's SYN/ACK Packets", RFC 5562,
              DOI 10.17487/RFC5562, June 2009,
              <http://www.rfc-editor.org/info/rfc5562>.

   [RFC6982]  Sheffer, Y. and A. Farrel, "Improving Awareness of Running
              Code: The Implementation Status Section", RFC 6982,
              DOI 10.17487/RFC6982, July 2013,
              <http://www.rfc-editor.org/info/rfc6982>.



Bensley, et al.            Expires May 5, 2016                 [Page 12]


Internet-Draft                    DCTCP                    November 2015


   [DCTCP10]  Alizadeh, M., Greenberg, A., Maltz, D., Padhye, J., Patel,
              P., Prabhakar, B., Sengupta, S., and M. Sridharan, "Data
              Center TCP (DCTCP)", DOI 10.1145/1851182.1851192,  Proc.
              ACM SIGCOMM 2010 Conference (SIGCOMM 10), August 2010,
              <http://dl.acm.org/citation.cfm?doid=1851182.1851192>.

   [ODCTCP]   Kato, M., "Improving Transmission Performance with One-
              Sided Datacenter TCP",  M.S. Thesis, Keio University,
              2014, <http://eggert.org/students/kato-thesis.pdf>.

   [BSDCAN]   Kato, M., Eggert, L., Zimmermann, A., van Meter, R., and
              H. Tokuda, "Extensions to FreeBSD Datacenter TCP for
              Incremental Deployment Support",  BSDCan 2015, June 2015,
              <https://www.bsdcan.org/2015/schedule/events/559.en.html>.

   [ADCTCP]   Alizadeh, M., Javanmard, A., and B. Prabhakar, "Analysis
              of DCTCP: Stability, Convergence, and Fairness",
              DOI 10.1145/1993744.1993753,  Proc. ACM SIGMETRICS Joint
              International Conference on Measurement and Modeling of
              Computer Systems (SIGMETRICS 11), June 2011,
              <https://dl.acm.org/citation.cfm?id=1993753>.

   [LINUX]    Borkmann, D. and F. Westphal, "Linux DCTCP patch", 2014,
              <https://git.kernel.org/cgit/linux/kernel/git/davem/net-
              next.git/
              commit/?id=e3118e8359bb7c59555aca60c725106e6d78c5ce>.

   [FREEBSD]  Kato, M. and H. Panchasara, "DCTCP (Data Center TCP)
              implementation", 2015,
              <https://github.com/freebsd/freebsd/
              commit/8ad879445281027858a7fa706d13e458095b595f>.

   [MORGANSTANLEY]
              Judd, G., "Attaining the Promise and Avoiding the Pitfalls
              of TCP in the Datacenter",  Proc. 12th USENIX Symposium on
              Networked Systems Design and Implementation (NSDI 15), May
              2015, <https://www.usenix.org/conference/nsdi15/technical-
              sessions/presentation/judd>.

   [RFC3168-ERRATA3639]
              Scheffenegger, R., "RFC3168 Errata ID 3639", 2013,
              <http://www.rfc-editor.org/
              errata_search.php/doc/html/rfc3168&eid=3639>.








Bensley, et al.            Expires May 5, 2016                 [Page 13]


Internet-Draft                    DCTCP                    November 2015


Authors' Addresses

   Stephen Bensley
   Microsoft
   One Microsoft Way
   Redmond, WA  98052
   USA

   Phone: +1 425 703 5570
   Email: sbens@microsoft.com


   Lars Eggert
   NetApp
   Sonnenallee 1
   Kirchheim  85551
   Germany

   Phone: +49 151 120 55791
   Email: lars@netapp.com
   URI:   http://eggert.org/


   Dave Thaler
   Microsoft

   Phone: +1 425 703 8835
   Email: dthaler@microsoft.com


   Praveen Balasubramanian
   Microsoft

   Phone: +1 425 538 2782
   Email: pravb@microsoft.com


   Glenn Judd
   Morgan Stanley

   Phone: +1 973 979 6481
   Email: glenn.judd@morganstanley.com









Bensley, et al.            Expires May 5, 2016                 [Page 14]