TRILL Working Group                                         Deepak Kumar
Internet Draft                                               Samer Salam
                                                                   Cisco
Intended Status: Standard Track                       Tissa Senevirathne
                                                              Consultant
Expires April 2016                                      October 12, 2015

                             TRILL OAM MIB
                    draft-ietf-trill-oam-mib-11.txt


   Abstract

   This document specifies the Management Information Base (MIB) for the
   IETF TRILL (Transparent Interconnection of Lots of Links) OAM
   (Operations, Administration, and Maintenance) objects.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 14, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.



Kumar et al.             Expires April 14, 2016                 [Page 1]


Internet Draft               TRILL OAM MIB              October 12, 2015


Table of Contents

   1. Introduction  . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2. The Internet-Standard Management Framework  . . . . . . . . . .  2
   3. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . .  3
   4. Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
   5. Structure of the MIB module . . . . . . . . . . . . . . . . . .  4
     5.1. Textual Conventions . . . . . . . . . . . . . . . . . . . .  4
     5.2.  The TRILL OAM MIB Subtree  . . . . . . . . . . . . . . . .  5
       5.3.1.  The Notifications Subtree  . . . . . . . . . . . . . .  5
       5.3.2. The Table Structures  . . . . . . . . . . . . . . . . .  5
         5.3.2.1. trillOamMepTable Objects  . . . . . . . . . . . . .  5
         5.3.2.2. trillOamMepFlowCfgTable Objects . . . . . . . . . .  6
         5.3.2.3. trillOamPtrTable Objects  . . . . . . . . . . . . .  6
         5.3.2.4. trillOamMtvrTable Objects . . . . . . . . . . . . .  6
         5.3.2.5. trillOamMepDbTable Objects  . . . . . . . . . . . .  6
   6. Relationship to other MIB modules . . . . . . . . . . . . . . .  7
     6.1.  Relationship to the IEEE8021-TC-MIB  . . . . . . . . . . .  7
     6.2. Relationship to the IEEE8021-CFM-MIB  . . . . . . . . . . .  8
     6.3.  MIB modules required for IMPORTS . . . . . . . . . . . . .  8
   7. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . .  8
   8. Security Considerations . . . . . . . . . . . . . . . . . . . . 43
   9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 46
   10.  Contributors  . . . . . . . . . . . . . . . . . . . . . . . . 47
   11.  References  . . . . . . . . . . . . . . . . . . . . . . . . . 47
     11.1.  Normative References  . . . . . . . . . . . . . . . . . . 47
     11.2.  Informative References  . . . . . . . . . . . . . . . . . 48



1. Introduction

   Overall, TRILL OAM (Operations, Administration, and Maintenance)
   meets the requirements given in [RFC6905]. The general framework for
   TRILL OAM is specified in [RFC7174]. The details of the Fault
   Management (FM) solution, conforming to that framework, are presented
   in [RFC7455]. The solution leverages the message format defined in
   Ethernet Connectivity Fault Management (CFM) [802.1Q] as the basis
   for the TRILL OAM message channel.

   This document uses the CFM MIB modules defined in [802.1Q] as the
   basis for TRILL OAM MIB and augments the existing tables to add new
   TRILL managed objects required by TRILL. This document further
   specifies a new table with associated managed objects for TRILL OAM
   specific capabilities.

2. The Internet-Standard Management Framework




Kumar et al.             Expires April 14, 2016                 [Page 2]


Internet Draft               TRILL OAM MIB              October 12, 2015


   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB. MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI). This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

3. Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   RFC-2119 [RFC2119].

   Acronyms used in the document include the following:

   MTVM  - Multi-destination Tree Verification Message [RFC7455]

   MTVR  - Multi-destination Tree Verification Reply [RFC7455]

   PTM   - Path Trace Message [RFC7455]

   PTR   - Path Trace Reply [RFC7455]

   MEP   - Maintenance End Point [RFC7174] [802.1Q]

   MIP   - Maintenance Intermediate Point [RFC7174] [802.1Q]

   MP    - Maintenance Point [RFC7174]

   CCM   - Continuity Check Message [802.1Q]

   FGL   - Fine-Grained Label

   LBM   - Loopback Message [802.1Q]

   LBR   - Loopback Reply [802.1Q]

   TRILL - Transparent Interconnection of Lots of Links [RFC6325]






Kumar et al.             Expires April 14, 2016                 [Page 3]


Internet Draft               TRILL OAM MIB              October 12, 2015


4. Overview

The TRILL-OAM-MIB module provides an overall framework for managing
TRILL OAM. It leverages the IEEE8021-CFM-MIB and IEEE8021-CFM-V2-MIB
modules defined in [802.1Q], and augments the Maintenance End Point
(MEP) and MEP Db entries. It also adds a new table for TRILL OAM
specific messages.


5. Structure of the MIB module

Objects in this MIB module are arranged into subtrees. Each subtree is
organized as a set of related objects. The various subtrees are shown
below, supplemented with the required elements of the IEEE8021-CFM-MIB
module.

5.1. Textual Conventions

Textual conventions are defined to represent object types relevant to
the TRILL OAM MIB.































Kumar et al.             Expires April 14, 2016                 [Page 4]


Internet Draft               TRILL OAM MIB              October 12, 2015


5.2.  The TRILL OAM MIB Subtree

TRILL-OAM MIB Tree describe below consists of trilloamNotifications
(Traps) and trillOamMibObjects. The trilloamNotifications are sent to
the management entity whenever a MEP loses/restores contact with its
peer Flow MEPs.

The TRILL OAM MIB Per MEP Objects are defined in the trillOamMepTable.
The trillOamMepTable augments the dot1agCfmMepEntry (please see section
6.1) defined in IEEE8021-CFM-MIB. It includes objects that are locally
defined for an individual MEP and its associated Flow.

TRILL-OAM-MIB

  |--trillOamNotifications          (trillOamMib 0}

     |--trillOamFaultAlarm

  |--trillOamMibObjects             {trillOamMib 1}

     |--trillOamMep                 {trillOamMibObjects 1}

        |--trillOamMepTable         {trillOamMep 1}  - Local TRLL config

        |--trillOamMepFlowCfgTable

        |--trillOamPtrTable

        |--trillOamMtvrTable

        |--trillOamMepDbTable


5.3.1.  The Notifications Subtree

Notifications (fault alarms) are sent to the management entity with the
OID of the MEP that has detected the fault. Notifications are generated
whenever MEP loses/restores contact with its peer Flow MEPs.

5.3.2. The Table Structures

The TRILL OAM MIB Per MEP Objects are defined in the trillOamMepTable.
The trillOamMepTable augments the dot1agCfmMepEntry (please see section
6.1) defined in IEEE8021-CFM-MIB. It includes objects that are locally
defined for an individual MEP and its associated Flow.

5.3.2.1. trillOamMepTable Objects




Kumar et al.             Expires April 14, 2016                 [Page 5]


Internet Draft               TRILL OAM MIB              October 12, 2015


   This table is an extension of the dot1agCfmMepTable. Rows are
   automatically added or deleted from this table based upon row
   creation and destruction of the dot1agCfmMepTable.

   This table represents the local MEP TRILL OAM configuration table.
   The primary purpose of this table is provide local parameters for the
   TRILL OAM function found in [RFC7455] and instantiated at a MEP.


5.3.2.2. trillOamMepFlowCfgTable Objects

   Each row in this table represents a Flow Configuration Entry for the
   associated MEP. This table uses four indices. The first three indices
   are the indices of the Maintenance Domain, MaNet, and MEP tables. The
   fourth index is the specific Flow Configuration Entry on the selected
   MEP. Some write-able objects in this table are only applicable in
   certain cases (as described under each object below), and attempts to
   write values for them in other cases will be ignored.


5.3.2.3. trillOamPtrTable Objects

   Each row in this table represents a Path Trace reply Entry for the
   Defined MEP and Transaction. This table uses four indices. The first
   three indices identify the MEP and the fourth index specifies the
   transaction identifier. This transaction identifier uniquely
   identifies the response for a MEP, which can have multiple flow.

5.3.2.4. trillOamMtvrTable Objects

   This table includes managed objects for the Multi-Destination Reply.
   Each row in the table represents a Multi-destination Reply Entry for
   the defined MEP and Transaction. This table uses the following five
   indices: 1) Maintenance Domain, 2) MANET, 3) MEP tables, 4)
   Transaction identifier of selected MEP, and 5) receive order of
   Multi-destination replies.

   Some write-able objects in this table are only applicable in certain
   cases (as described under each object below), and attempts to write a
   value for them in other cases will be ignored.


5.3.2.5. trillOamMepDbTable Objects

   This table is an augmentation of the dot1agCfmMepDbTable, and rows
   are automatically added or deleted from this table based upon row
   creation and destruction of the dot1agCfmMepDbTable.




Kumar et al.             Expires April 14, 2016                 [Page 6]


Internet Draft               TRILL OAM MIB              October 12, 2015


6. Relationship to other MIB modules

   The IEEE8021-CFM-MIB, and LLDP-MIB contain objects that are relevant
   to the TRILL OAM MIB. Management objects contained in these modules
   are not duplicated here, to reduce overlap to the extent possible.
   From the IEEE8021-CFM-MIB following objects are imported

      o dot1agCfmMdIndex

      o dot1agCfmMaIndex

      o dot1agCfmMepIdentifier

      o dot1agCfmMepEntry

      o dot1agCfmMepDbEntry

      o Dot1agCfmIngressActionFieldValue

      o Dot1agCfmEgressActionFieldValue

      o Dot1agCfmRemoteMepState


   From the LLDP-MIB following objects are imported

      o LldpChassisId

      o LldpChassisIdSubtype

      o LldpPortId

6.1.  Relationship to the IEEE8021-TC-MIB

      In TRILL, traffic labeling can be done using either a 12-bit VLAN
      or a 24-bit fine grain label [RFC7172].

      The IEEE8021-TC-MIB definition of IEEE8021ServiceSelectorType
      includes the following two values:

      - 1 representing a vlanId, and

      - 2 representing a 24-bit isid

      We have chosen to use value 2 for TRILL's fine grain label. As
      such, TRILL-OAM-MIB will import IEEE8021ServiceSelectorType,
      IEEE8021ServiceSelectorValueOrNone, and
      IEEE8021ServiceSelectorValue from IEEE8021-TC-MIB.



Kumar et al.             Expires April 14, 2016                 [Page 7]


Internet Draft               TRILL OAM MIB              October 12, 2015


6.2. Relationship to the IEEE8021-CFM-MIB

   trillOamMepTable augments dot1agCfmMepEntry. Implementation of
   IEEE8021-CFM-MIB is required as we are augmenting the IEEE-CFM-MIB
   Table. Objects/Tables that are not applicable to a TRILL
   implementation have to be handled by the TRILL implementation back
   end and appropriate default values, as described in IEEE8021-CFM-MIB,
   have to be returned.

   The TRILL OAM implementation doesn't support the Link Trace Message
   or Link Trace Reply since, as described in RFC7455, the Path Trace
   Message and Reply for unicast traffic and Multi-destination Tree
   verification Message and Reply for multicast traffic have been
   substituted for them. Statistics for these messages should default as
   per IEEE8021-CFM-MIB.

6.3.  MIB modules required for IMPORTS

   The following MIB module IMPORTS objects from SNMPv2-SMI [RFC2578],
   SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], IEEE-8021-CFM-MIB, LLDP-
   MIB.

7. Definitions

   TRILL-OAM-MIB DEFINITIONS ::= BEGIN

   IMPORTS

       MODULE-IDENTITY,
       OBJECT-TYPE,
       Counter32,
       Unsigned32,
       Integer32,
       mib-2,
       NOTIFICATION-TYPE
          FROM SNMPv2-SMI
       RowStatus,
       TruthValue,
       TimeStamp,
       MacAddress
           FROM SNMPv2-TC
       OBJECT-GROUP,
       NOTIFICATION-GROUP,
       MODULE-COMPLIANCE
           FROM SNMPv2-CONF
       dot1agCfmMdIndex,
       dot1agCfmMaIndex,
       dot1agCfmMepIdentifier,



Kumar et al.             Expires April 14, 2016                 [Page 8]


Internet Draft               TRILL OAM MIB              October 12, 2015


       dot1agCfmMepEntry,
       dot1agCfmMepDbEntry,
       Dot1agCfmIngressActionFieldValue,
       Dot1agCfmEgressActionFieldValue,
       Dot1agCfmRemoteMepState
           FROM IEEE8021-CFM-MIB
       LldpChassisId,
       LldpChassisIdSubtype,
       LldpPortId,
       LldpPortIdSubtype
           FROM LLDP-MIB;

   trillOamMib MODULE-IDENTITY
       LAST-UPDATED    "201508231200Z"
       ORGANIZATION    "IETF TRILL WG"
       CONTACT-INFO
               "E-mail: trill@ietf.org"
       DESCRIPTION
           "This MIB module contains the management objects for the
           management of TRILL Services Operations, Administration
           and Maintenance.
           Initial version. Published as RFC xxxx.

           -------------------------------------------------------------
           Reference Overview

           A number of base documents have been used to create the
           Textual Conventions MIB. The following are the
           abbreviations for the baseline documents:

           [CFM] refers to 'Connectivity Fault Management',
           IEEE 802.1Q-2014, December 2014
           [Q.840.1] refers to 'ITU-T Requirements and analysis for
           NMS-EMS management interface of Ethernet over Transport and
           Metro Ethernet Network (EoT/MEN)', March 2007
           [Y.1731] refers to ITU-T Y.1731 'OAM functions and mechanisms
           for Ethernet based networks', February 2011
           -------------------------------------------------------------


           Abbreviations Used

           Term         Definition
           CCM          Continuity Check Message
           CFM          Connectivity Fault Management
           CoS          Class of Service
           IEEE         Institute of Electrical and Electronics
                        Engineers



Kumar et al.             Expires April 14, 2016                 [Page 9]


Internet Draft               TRILL OAM MIB              October 12, 2015


           IETF         Internet Engineering Task Force
           ITU-T        International Telecommunication Union -
                        Telecommunication Standardization Bureau
           MAC          Media Access Control
           MA           Maintenance Association (equivalent to a MEG)
           MD           Maintenance Domain (equivalent to a OAM
                                            Domain in MEF 17)
           MD Level     Maintenance Domain Level (equivalent to a
                                                  MEG level)
           ME           Maintenance Entity
           MEG          Maintenance Entity Group (equivalent to a MA)
           MEG Level    Maintenance Entity Group Level (equivalent to
                                                        MD Level)
           MEP          Maintenance Association End Point or MEG End
                        Point
           MIB          Management Information Base
           MIP          Maintenance Domain Intermediate Point or
                        MEG Intermediate Point
           MP           Maintenance Point. One of either a MEP or a MIP
           OAM          Operations, Administration, and Maintenance
                        On-Demand OAM actions that are initiated via
                        manual intervention for a limited time to carry
                        out diagnostics.  On-Demand OAM can result in
                        singular or periodic OAM actions during the
                        diagnostic time interval
           PDU          Protocol Data Unit
           RFC          Request for Comment
           SNMP         Simple Network Management Protocol
           SNMP Agent   An SNMP entity containing one or more command
                        responder and/or notification originator
                        applications(along with their associated SNMP
                        engine).  Typically implemented in Network
                        Element.
           SNMP Manager An SNMP entity containing one or more command
                        generator and/or notification receiver
                        applications (along with their associated SNMP
                        engine). Typically implemented in an
                        EMS or NMS.
           TLV          Type Length Value, a method of encoding Objects
           UTC          Coordinated Universal Time
           UNI          User-to-Network Interface
           VLAN         Virtual LAN
           PTR          Path Trace Reply
           PTM          Path Trace Message
           MTVR         Multi-destination Tree Verification Reply
           MTVM         Multi-destination Tree Verification Message"

       REVISION        "201508231200Z"



Kumar et al.             Expires April 14, 2016                [Page 10]


Internet Draft               TRILL OAM MIB              October 12, 2015


       DESCRIPTION
           "Initial version. Published as RFC xxxx."
       ::= { mib-2 12000 }


   -- RFC Ed.: assigned by IANA, see section 9 for details
   --
   -- *****************************************************************
   -- Object definitions in the TRILL OAM MIB Module
   -- *****************************************************************

   trillOamNotifications  OBJECT IDENTIFIER
       ::= { trillOamMib 0 }

   trillOamMibObjects  OBJECT IDENTIFIER
       ::= { trillOamMib 1 }

   trillOamMibConformance  OBJECT IDENTIFIER
       ::= { trillOamMib 2 }

   -- *****************************************************************
   -- Groups in the TRILL OAM MIB Module
   -- *****************************************************************

   trillOamMep  OBJECT IDENTIFIER
       ::= { trillOamMibObjects 1 }


   -- *****************************************************************
   -- TRILL OAM MEP Configuration
   -- *****************************************************************

   trillOamMepTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamMepEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table is an extension of the dot1agCfmMepTable and
            rows are automatically added or deleted from this table
            based upon row creation and destruction of the
            dot1agCfmMepTable.

           This table represents the local MEP TRILL OAM
           configuration table. The primary purpose of this table
           is provide local parameters for the TRILL OAM function
           found in RFC 7455 and instantiated at a MEP."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 1 }



Kumar et al.             Expires April 14, 2016                [Page 11]


Internet Draft               TRILL OAM MIB              October 12, 2015


   trillOamMepEntry OBJECT-TYPE
       SYNTAX          TrillOamMepEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamMepTable."
       AUGMENTS           { dot1agCfmMepEntry  }
       ::= { trillOamMepTable 1 }

   TrillOamMepEntry ::= SEQUENCE {
           trillOamMepRName               Unsigned32,
           trillOamMepNextPtmTId          Counter32,
           trillOamMepNextMtvmTId         Counter32,
           trillOamMepPtrIn               Counter32,
           trillOamMepPtrInOutofOrder     Counter32,
           trillOamMepPtrOut              Counter32,
           trillOamMepMtvrIn              Counter32,
           trillOamMepMtvrInOutofOrder    Counter32,
           trillOamMepMtvrOut             Counter32,
           trillOamMepTxLbmDestRName      Unsigned32,
           trillOamMepTxLbmHC             Unsigned32,
           trillOamMepTxLbmReplyModeOob   TruthValue,
           trillOamMepTransmitLbmReplyIp  OCTET STRING,
           trillOamMepTxLbmFlowEntropy    OCTET STRING,
           trillOamMepTxPtmDestRName      Unsigned32,
           trillOamMepTxPtmHC             Unsigned32,
           trillOamMepTxPtmReplyModeOob   TruthValue,
           trillOamMepTransmitPtmReplyIp  OCTET STRING,
           trillOamMepTxPtmFlowEntropy    OCTET STRING,
           trillOamMepTxPtmStatus         TruthValue,
           trillOamMepTxPtmResultOK       TruthValue,
           trillOamMepTxPtmSeqNumber      Unsigned32,
           trillOamMepTxPtmMessages       Integer32,
           trillOamMepTxMtvmTree          Unsigned32,
           trillOamMepTxMtvmHC            Unsigned32,
           trillOamMepTxMtvmReplyModeOob  TruthValue,
           trillOamMepTransmitMtvmReplyIp OCTET STRING,
           trillOamMepTxMtvmFlowEntropy   OCTET STRING,
           trillOamMepTxMtvmStatus        TruthValue,
           trillOamMepTxMtvmResultOK      TruthValue,
           trillOamMepTxMtvmMessages      Integer32,
           trillOamMepTxMtvmSeqNumber     Unsigned32,
           trillOamMepTxMtvmScopeList     OCTET STRING,
           trillOamMepDiscontinuityTime   TimeStamp
   }

   trillOamMepRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)



Kumar et al.             Expires April 14, 2016                [Page 12]


Internet Draft               TRILL OAM MIB              October 12, 2015


       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "This object contains the Rbridge NickName of the TRILL
           Rbridge as defined in RFC 6325 section 3.7."
       REFERENCE "RFC 7455 and RFC 6325 section 3.7"
       ::= { trillOamMepEntry 1 }

   trillOamMepNextPtmTId OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next sequence number/transaction identifier to be sent in a
            Multi-destination message. This sequence number can be zero
            because it wraps around. Implementation of this identifier
            should be should provide a unique code value in order to
            identify the Transaction ID for a MEP with multiple flows."
       REFERENCE "RFC 7455 10.1.1"
       ::= { trillOamMepEntry 2 }

   trillOamMepNextMtvmTId OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next sequence number/transaction identifier to be sent in a
           Multi-destination message. This sequence number can be zero
           because it wraps around. Implementation should be unique to
           identify Transaction ID for a MEP with multiple flows."
       REFERENCE "RFC 7455 11.2.1"
       ::= { trillOamMepEntry 3 }

   trillOamMepPtrIn OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, in-order Path Trace Replies
            received."
       REFERENCE "RFC 7455 section 10"
       ::= { trillOamMepEntry 4 }

   trillOamMepPtrInOutofOrder OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION



Kumar et al.             Expires April 14, 2016                [Page 13]


Internet Draft               TRILL OAM MIB              October 12, 2015


           "Total number of valid, out-of-order Path Trace Replies
            received."
       REFERENCE "RFC 7455 section 10"
       ::= { trillOamMepEntry 5 }

   trillOamMepPtrOut OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, Path Trace Replies
            transmitted."
       REFERENCE "RFC 7455 section 10"
       ::= { trillOamMepEntry 6 }

   trillOamMepMtvrIn OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, in-order Multi-destination
            Replies received."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 7 }

   trillOamMepMtvrInOutofOrder OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, out-of-order Multi-destination
            Replies received."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 8 }

   trillOamMepMtvrOut OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, Multi-destination Replies
           transmitted."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 9 }

   trillOamMepTxLbmDestRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-create



Kumar et al.             Expires April 14, 2016                [Page 14]


Internet Draft               TRILL OAM MIB              October 12, 2015


       STATUS          current
       DESCRIPTION
           "The Target Destination Rbridge NickName Field, as
           defined in RFC 6325 section 3.7, to be transmitted."
       REFERENCE "RFC 7455 and RFC 6325 section 3.7"
       ::= { trillOamMepEntry 10 }

   trillOamMepTxLbmHC OBJECT-TYPE
       SYNTAX          Unsigned32(1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Hop Count to be transmitted.
           "
       REFERENCE "RFC 7455 section 9 and 3"
       ::= { trillOamMepEntry 11 }

   trillOamMepTxLbmReplyModeOob OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "True indicates that the Reply to an LBM is out of
           band and out of band IP Address TLV is to be
           transmitted. False indicates that In band reply is
           transmitted."
       REFERENCE "RFC 7455 9.2.1"
       ::= { trillOamMepEntry 12 }

   trillOamMepTransmitLbmReplyIp OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (4..16))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The IP address for an out of band IP Address TLV
            that is to be transmitted. Maximum length for IPv6
            is 16 OCTET and IPv4 is 4 OCTET."
       REFERENCE "RFC 7455 section 3"
       ::= { trillOamMepEntry 13 }

   trillOamMepTxLbmFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "96 Byte Flow Entropy, as defined in RFC 7455, to
            be transmitted."
       REFERENCE "RFC 7455 section 3"



Kumar et al.             Expires April 14, 2016                [Page 15]


Internet Draft               TRILL OAM MIB              October 12, 2015


       ::= { trillOamMepEntry 14 }

   trillOamMepTxPtmDestRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Target Destination Rbridge NickName Field,
           as defined in RFC 6325 section 3.7, to be transmitted."
       REFERENCE "RFC 7455 and RFC 6325 section 3.7"
       ::= { trillOamMepEntry 15 }

   trillOamMepTxPtmHC OBJECT-TYPE
       SYNTAX          Unsigned32 (1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Hop Count field to be transmitted."
       REFERENCE "RFC 7455 section 3"
       ::= { trillOamMepEntry 16 }

   trillOamMepTxPtmReplyModeOob OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "True indicates that a Reply to a PTM will be
            out of band and the out of band IP Address TLV
            is to be transmitted. False indicates that an
            in band reply  is transmitted."
       REFERENCE "RFC 7455 section 10"
       DEFVAL          { false }
       ::= { trillOamMepEntry 17 }

   trillOamMepTransmitPtmReplyIp OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (4..16))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The IP address for an out of band IP Address TLV
            to be Transmitted.  The  maximum length for an
            IPv6 address is 16 Octets.  The maximum length
            for an  IPv4 address is 4 octets."
       REFERENCE "RFC 7455 section 3 and 10"
       ::= { trillOamMepEntry 18 }

   trillOamMepTxPtmFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))



Kumar et al.             Expires April 14, 2016                [Page 16]


Internet Draft               TRILL OAM MIB              October 12, 2015


       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "96 Byte Flow Entropy, as defined in RFC 7455, to be
            transmitted."
       REFERENCE "RFC 7455 section 3"
       ::= { trillOamMepEntry 19 }

   trillOamMepTxPtmStatus OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "A Boolean flag set to true by the MEP Path Trace Initiator
           State Machine or a MIB manager to indicate that another PTM is
           being transmitted.  This is Reset to false by the MEP
           Initiator State Machine.  The PTM managed objects in the MEP
           table are used in a manner similar to that described for LBM
           transmission in dot1agCfmMepTable. As per RFC7455 section 10,
           Operation of the Path Trace Message is identical to the
           Loopback Message except that it is first transmitted with a
           TRILL Header Hop count field value of 1 and then retransmitted
           with an incrementeing Hop count until a response is received
           from the destination RBridge, or the Hop Count reaches a
           configured maximum value.  trillOamMepTxPtmStatus Status is
           reset to FALSE by initiator when last PTM is transmitted."
       REFERENCE "RFC 7455 section 10"
       DEFVAL          { false }
       ::= { trillOamMepEntry 20 }

   trillOamMepTxPtmResultOK OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "Indicates the following results of the operation:
           - true  The Path Trace Message(s) will be (or has been)
             sent.
           - false The Path Trace Message(s) will not be sent."
       REFERENCE "RFC 7455 section 10"
       DEFVAL          { true }
       ::= { trillOamMepEntry 21 }

   trillOamMepTxPtmSeqNumber OBJECT-TYPE
       SYNTAX          Unsigned32
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION



Kumar et al.             Expires April 14, 2016                [Page 17]


Internet Draft               TRILL OAM MIB              October 12, 2015


           "The Path Trace Transaction Identifier of the first
            PTM (to be) sent. The value returned is
            undefined if trillOamMepTxPtmResultOK is false."
       REFERENCE "RFC 7455 section 10"
       ::= { trillOamMepEntry 22 }

   trillOamMepTxPtmMessages OBJECT-TYPE
       SYNTAX          Integer32 (1..1024)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The number of Path Trace messages to be transmitted.
            As per RFC 7455 section 10, the first Path Trace
            Message is transmitted with a Hop count of 1 and an
            RBridge may continue to retransmit the request at
            periodic intervals with an incrementing Hop Count
            until a response is received from the destination
            Rbridge, or the Hop Count reaches a configured
            maximum value. The event of the Destination
            response being received or the Hop count reaching
            its maximum is treated as a single Counter
            increment of this object."
       REFERENCE "RFC 7455 section 10"
       ::= { trillOamMepEntry 23 }

   trillOamMepTxMtvmTree OBJECT-TYPE
       SYNTAX          Unsigned32
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Multi-destination Tree identifier, as
            defined in RFC6325, for an MTVM."
       ::= { trillOamMepEntry 24 }

   trillOamMepTxMtvmHC OBJECT-TYPE
       SYNTAX          Unsigned32(1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Hop Count field to be transmitted.
           "
       REFERENCE "RFC 7455 section 3, RFC 6325 section 3"
       ::= { trillOamMepEntry 25 }

   trillOamMepTxMtvmReplyModeOob OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current



Kumar et al.             Expires April 14, 2016                [Page 18]


Internet Draft               TRILL OAM MIB              October 12, 2015


       DESCRIPTION
           "True Indicates that the reply to an MTVM is out of
           band and this out of band IP Address TLV is where the
           reply is to be transmitted.
           False indicates that an in band reply is transmitted."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 26 }

   trillOamMepTransmitMtvmReplyIp OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (4..16))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "IP address for an out of band IP Address TLV that is
            to be transmitted. The Maximum length for IPv6 is 16
            OCTET and IPv4 is 4 OCTET."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 27 }

   trillOamMepTxMtvmFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "96 Byte Flow Entropy, as defined in RFC 7455, to be
            transmitted."
       REFERENCE "RFC 7455 section 3"
       ::= { trillOamMepEntry 28 }

   trillOamMepTxMtvmStatus OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "A Boolean flag set to true by the MEP Multi Destination
           Initiator State Machine or a MIB manager to indicate
           that another MTVM is being transmitted.
           Reset to false by the MEP Initiator State Machine.
           The MTVM managed objects in the MEP table are used
           in a manner similar to that described for LBM
           transmission in dot1agCfmMepTable. As per RFC7455
           section 11, operation of the MTVM Message is
           identical to the Loopback Message except that it is
           first transmitted with a TRILL Header Hop count
           field value of 1 and it is retransmitted incrementing
           the Hop count until a response is received from the
           destination RBridge or the Hop Count reaches a
           configured maximum value. trillOamMepTxMtvmStatus



Kumar et al.             Expires April 14, 2016                [Page 19]


Internet Draft               TRILL OAM MIB              October 12, 2015


           Status is reset to FALSE by the initiator when the last
           MTVM is transmitted."
       REFERENCE "RFC 7455 section 11"
       DEFVAL          { false }
       ::= { trillOamMepEntry 29 }

   trillOamMepTxMtvmResultOK OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "Indicates the result of the operation in
            the following way:
           - true  The Multi-destination Message(s) will be
             (or has been) sent.
           - false The Multi-destination Message(s) will not be sent."
       REFERENCE "RFC 7455 section 11"
       DEFVAL          { true }
       ::= { trillOamMepEntry 30 }

   trillOamMepTxMtvmMessages OBJECT-TYPE
       SYNTAX          Integer32 (1..1024)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The number of Multi Destination messages to be transmitted.
            The Rbridge transmit the Multi Destination message
            incrementing the session Identification Number at periodic
            interval until this count expires."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 31 }

   trillOamMepTxMtvmSeqNumber OBJECT-TYPE
       SYNTAX          Unsigned32
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Multi-destination Transaction Identifier of the
           first MTVM (to be)
           sent. The value returned is undefined if
           trillOamMepTxMtvmResultOK is false."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 32 }

   trillOamMepTxMtvmScopeList OBJECT-TYPE
       SYNTAX          OCTET STRING
       MAX-ACCESS      read-create
       STATUS          current



Kumar et al.             Expires April 14, 2016                [Page 20]


Internet Draft               TRILL OAM MIB              October 12, 2015


       DESCRIPTION
           "The Multi-destination Rbridge Scope list, which
              requires 2 octets per Rbridge."
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 33 }

   trillOamMepDiscontinuityTime OBJECT-TYPE
       SYNTAX          TimeStamp
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Snapshot of the value of the sysUpTime object at the
            beginning of the latest period of continuity of the
            statistical counters associated with this MEP."
       ::= { trillOamMepEntry 34 }


   -- *****************************************************************
   -- TRILL OAM Tx Measurement Configuration Table
   -- *****************************************************************

   trillOamMepFlowCfgTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamMepFlowCfgEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table includes configuration objects and operations
            for the TRILL OAM RFC 7455.

            Each row in the table represents a Flow configuration
            Entry for the defined MEP. This table uses four indices.
            The first three indices are the indices of the Maintenance
            Domain, MaNet, and MEP tables. The fourth index is the
            specific flow configuration Entry on the selected MEP.

           Some writable objects in this table are only applicable in
           certain cases (as described under each object), and
           attempts to write values for them in other cases
           will be ignored."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 2 }

   trillOamMepFlowCfgEntry OBJECT-TYPE
       SYNTAX          TrillOamMepFlowCfgEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamMepFlowCfgTable."



Kumar et al.             Expires April 14, 2016                [Page 21]


Internet Draft               TRILL OAM MIB              October 12, 2015


       INDEX           {
                           dot1agCfmMdIndex,
                           dot1agCfmMaIndex,
                           dot1agCfmMepIdentifier,
                           trillOamMepFlowCfgIndex
                       }
       ::= { trillOamMepFlowCfgTable 1 }

   TrillOamMepFlowCfgEntry ::= SEQUENCE {
           trillOamMepFlowCfgIndex       Unsigned32,
           trillOamMepFlowCfgFlowEntropy OCTET STRING,
           trillOamMepFlowCfgDestRName   Unsigned32,
           trillOamMepFlowCfgFlowHC      Unsigned32,
           trillOamMepFlowCfgRowStatus   RowStatus
           }

   trillOamMepFlowCfgIndex OBJECT-TYPE
       SYNTAX          Unsigned32 (1..65535)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "An index to the TRILL OAM MEP Flow Configuration table which
           indicates the specific Flow for the MEP.

           The index is never reused for other flow sessions on the
           same MEP while this session is active.  The index value
           keeps increasing until it wraps to 0. This value can also be
           used in Flow-identifier TLV RFC 7455."
       REFERENCE "RFC 7455"
       ::= { trillOamMepFlowCfgEntry 1 }

   trillOamMepFlowCfgFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "This is 96 byte of Flow Entropy as described in
           TRILL OAM RFC 7455."
       REFERENCE "RFC 7455 section 3"
       ::= { trillOamMepFlowCfgEntry 2 }

   trillOamMepFlowCfgDestRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Target Destination Rbridge NickName Field, as
           defined in RFC 6325 section 3.7, to be transmitted."



Kumar et al.             Expires April 14, 2016                [Page 22]


Internet Draft               TRILL OAM MIB              October 12, 2015


       REFERENCE "RFC 7455 section 3 and RFC 6325 section 3.7"
       ::= { trillOamMepFlowCfgEntry 3 }

   trillOamMepFlowCfgFlowHC OBJECT-TYPE
       SYNTAX          Unsigned32 (1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Time to Live field to be transmitted."
       REFERENCE "RFC 7455 section 3 and RFC 6325 section 3.7"
       ::= { trillOamMepFlowCfgEntry 4 }

   trillOamMepFlowCfgRowStatus OBJECT-TYPE
       SYNTAX          RowStatus
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The status of the row.

           The writable columns in a row cannot be changed if the row
           is active. All columns MUST have a valid value before a row
           can be activated."
       ::= { trillOamMepFlowCfgEntry 5 }


   -- ******************************************************************
   -- TRILL OAM Path Trace Reply Table
   -- ******************************************************************

   trillOamPtrTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamPtrEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table includes Path Trace Reply objects and
            operations for TRILL OAM as described in RFC 7455.

           Each row in the table represents a Path Trace Reply Entry for
           the defined MEP and Transaction. This table uses four
           indices. The first three indices are the indices of the
           Maintenance Domain,
           MaNet, and MEP tables. The fourth index is the specific
           Transaction Identifier on the selected MEP.

           Some writable objects in this table are only applicable in
           certain cases (as described under each object),
           and attempts to
           write values for them in other cases will be ignored."



Kumar et al.             Expires April 14, 2016                [Page 23]


Internet Draft               TRILL OAM MIB              October 12, 2015


       REFERENCE       "RFC 7455"
       ::= { trillOamMep 3 }

   trillOamPtrEntry OBJECT-TYPE
       SYNTAX          TrillOamPtrEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamPtrTable."
       INDEX           {
                           dot1agCfmMdIndex,
                           dot1agCfmMaIndex,
                           dot1agCfmMepIdentifier,
                           trillOamMepPtrTransactionId
                       }
       ::= { trillOamPtrTable 1 }

   TrillOamPtrEntry ::= SEQUENCE {
           trillOamMepPtrTransactionId           Unsigned32,
           trillOamMepPtrHC                      Unsigned32,
           trillOamMepPtrFlag                    Unsigned32,
           trillOamMepPtrErrorCode               Unsigned32,
           trillOamMepPtrTerminalMep             TruthValue,
           trillOamMepPtrLastEgressId            Unsigned32,
           trillOamMepPtrIngress       Dot1agCfmIngressActionFieldValue,
           trillOamMepPtrIngressMac              MacAddress,
           trillOamMepPtrIngressPortIdSubtype    LldpPortIdSubtype,
           trillOamMepPtrIngressPortId           LldpPortId,
           trillOamMepPtrEgress        Dot1agCfmEgressActionFieldValue,
           trillOamMepPtrEgressMac               MacAddress,
           trillOamMepPtrEgressPortIdSubtype     LldpPortIdSubtype,
           trillOamMepPtrEgressPortId            LldpPortId,
           trillOamMepPtrChassisIdSubtype        LldpChassisIdSubtype,
           trillOamMepPtrChassisId               LldpChassisId,
           trillOamMepPtrOrganizationSpecificTlv OCTET STRING,
           trillOamMepPtrNextHopNicknames        OCTET STRING
   }

   trillOamMepPtrTransactionId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..4294967295)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "Transaction identifier/sequence number returned by a
            previous transmit path trace message command,
            indicating which PTM's response is going to be returned."
       REFERENCE       "RFC 7455 section 10"
       ::= { trillOamPtrEntry 1 }



Kumar et al.             Expires April 14, 2016                [Page 24]


Internet Draft               TRILL OAM MIB              October 12, 2015


   trillOamMepPtrHC  OBJECT-TYPE
       SYNTAX          Unsigned32 (1..63)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Hop Count field value for a returned PTR."
       REFERENCE       "RFC 7455"
       ::= { trillOamPtrEntry 2 }

   trillOamMepPtrFlag OBJECT-TYPE
       SYNTAX          Unsigned32 (0..15)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "FCOI (TRILL OAM Message TLV) field value for a
            returned PTR."
       REFERENCE       "RFC 7455, 8.4.3"
       ::= { trillOamPtrEntry 3 }

   trillOamMepPtrErrorCode OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Return Code and Return Sub code value for a returned PTR."
       REFERENCE       "RFC 7455, 8.4.3"
       ::= { trillOamPtrEntry 4 }

   trillOamMepPtrTerminalMep OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "A boolean value stating whether the forwarded PTM reached a
           MEP enclosing its MA, as returned in the Terminal MEP flag of
           the Flags field."
       REFERENCE       "RFC 7455"
       ::= { trillOamPtrEntry 5 }

   trillOamMepPtrLastEgressId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "An Integer field holding the Last Egress Identifier returned
           in the PTR Upstream Rbridge nickname TLV of the PTR.
           The Last Egress Identifier identifies the Upstream Nickname."
       REFERENCE       "RFC 7455 8.4.1"



Kumar et al.             Expires April 14, 2016                [Page 25]


Internet Draft               TRILL OAM MIB              October 12, 2015


       ::= { trillOamPtrEntry 6 }

   trillOamMepPtrIngress OBJECT-TYPE
       SYNTAX          Dot1agCfmIngressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Ingress Action Field of the PTR.
           The value ingNoTlv(0) indicates that no Reply Ingress TLV was
           returned in the PTM."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 7 }

   trillOamMepPtrIngressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the ingress MAC address field."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 8 }

   trillOamMepPtrIngressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrIngressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 9 }

   trillOamMepPtrIngressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrIngressPortId object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 10 }

   trillOamMepPtrEgress OBJECT-TYPE
       SYNTAX          Dot1agCfmEgressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Egress Action Field of the PTR.



Kumar et al.             Expires April 14, 2016                [Page 26]


Internet Draft               TRILL OAM MIB              October 12, 2015


           The value ingNoTlv(0) indicates that no Reply Egress TLV was
           returned in the PTM."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 11 }

   trillOamMepPtrEgressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the egress MAC address field."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 12 }

   trillOamMepPtrEgressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrEgressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 13 }

   trillOamMepPtrEgressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrEgressPortId object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 14 }

   trillOamMepPtrChassisIdSubtype OBJECT-TYPE
       SYNTAX          LldpChassisIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "This object specifies the format of the Chassis ID returned
           in the Sender ID TLV of the PTR, if any.  This value is
           meaningless if the trillOamMepPtrChassisId
           has a length of 0."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 15 }

   trillOamMepPtrChassisId OBJECT-TYPE
       SYNTAX          LldpChassisId



Kumar et al.             Expires April 14, 2016                [Page 27]


Internet Draft               TRILL OAM MIB              October 12, 2015


       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The Chassis ID returned in the Sender ID TLV of the PTR, if
           any. The format of this object is determined by the
           value of the trillOamMepPtrChassisIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 16 }

   trillOamMepPtrOrganizationSpecificTlv OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "All Organization specific TLVs returned in the PTR, if
           any.  Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 17 }

   trillOamMepPtrNextHopNicknames OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next hop Rbridge List TLV returned in the PTR, if
           any.  Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamPtrEntry 18 }


   -- ******************************************************************
   -- TRILL OAM Multi Destination Reply Table
   -- ******************************************************************

   trillOamMtvrTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamMtvrEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table includes Multi-destination Reply objects and
            operations for the TRILL OAM described in RFC 7455.

           Each row in the table represents a Multi-destination Reply
           Entry for the defined MEP and Transaction.  This table uses
           five indices.  The first three indices are the indices of the
           Maintenance Domain, MaNet, and MEP tables. The fourth index



Kumar et al.             Expires April 14, 2016                [Page 28]


Internet Draft               TRILL OAM MIB              October 12, 2015


           is the specific Transaction Identifier on the selected MEP.
           The fifth index is the receive order of Multi-destination
           replies.

           Some writable objects in this table are only applicable in
           certain cases (as described under each object), and attempts
           to write values for them in other cases will be ignored."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 4 }

   trillOamMtvrEntry OBJECT-TYPE
       SYNTAX          TrillOamMtvrEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamMtvrTable."
       INDEX           {
                           dot1agCfmMdIndex,
                           dot1agCfmMaIndex,
                           dot1agCfmMepIdentifier,
                           trillOamMepPtrTransactionId,
                           trillOamMepMtvrReceiveOrder
                       }
       ::= { trillOamMtvrTable 1 }

   TrillOamMtvrEntry ::= SEQUENCE {
           trillOamMepMtvrTransactionId           Unsigned32,
           trillOamMepMtvrReceiveOrder            Unsigned32,
           trillOamMepMtvrFlag                    Unsigned32,
           trillOamMepMtvrErrorCode               Unsigned32,
           trillOamMepMtvrLastEgressId            Unsigned32,
           trillOamMepMtvrIngress    Dot1agCfmIngressActionFieldValue,
           trillOamMepMtvrIngressMac              MacAddress,
           trillOamMepMtvrIngressPortIdSubtype    LldpPortIdSubtype,
           trillOamMepMtvrIngressPortId           LldpPortId,
           trillOamMepMtvrEgress     Dot1agCfmEgressActionFieldValue,
           trillOamMepMtvrEgressMac               MacAddress,
           trillOamMepMtvrEgressPortIdSubtype     LldpPortIdSubtype,
           trillOamMepMtvrEgressPortId            LldpPortId,
           trillOamMepMtvrChassisIdSubtype        LldpChassisIdSubtype,
           trillOamMepMtvrChassisId               LldpChassisId,
           trillOamMepMtvrOrganizationSpecificTlv OCTET STRING,
           trillOamMepMtvrNextHopNicknames        OCTET STRING,
           trillOamMepMtvrReceiverAvailability    TruthValue,
           trillOamMepMtvrReceiverCount           TruthValue
   }

   trillOamMepMtvrTransactionId OBJECT-TYPE



Kumar et al.             Expires April 14, 2016                [Page 29]


Internet Draft               TRILL OAM MIB              October 12, 2015


       SYNTAX          Unsigned32 (0..4294967295)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "Transaction identifier/sequence number returned by a
           previous transmit Multi-destination message command
           indicating which MTVM's response is going to be returned."
       REFERENCE       "RFC 7455 section 11"
       ::= { trillOamMtvrEntry 1 }

   trillOamMepMtvrReceiveOrder OBJECT-TYPE
       SYNTAX          Unsigned32 (1..4294967295)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "An index to distinguish among multiple MTVR with same MTVR
            Transaction Identifier field value.
            trillOamMepMtvrReceiveOrder is assigned sequentially from 1,
            in the order that the Multi-destination Tree Initiator
            received the MTVRs."
       REFERENCE   "RFC 7455 section 11"
       ::= { trillOamMtvrEntry 2 }

   trillOamMepMtvrFlag OBJECT-TYPE
       SYNTAX          Unsigned32 (0..15)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "FCOI (TRILL OAM Message TLV) field value for a
            returned MTVR."
       REFERENCE       "RFC 7455, 8.4.2"
       ::= { trillOamMtvrEntry 3 }

   trillOamMepMtvrErrorCode OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Return Code and Return Sub code value for a returned MTVR."
       REFERENCE       "RFC 7455, 8.4.2"
       ::= { trillOamMtvrEntry 4 }

   trillOamMepMtvrLastEgressId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "An Integer field holding the Last Egress Identifier returned



Kumar et al.             Expires April 14, 2016                [Page 30]


Internet Draft               TRILL OAM MIB              October 12, 2015


           in the MTVR Upstream Rbridge Nickname TLV of the MTVR.  The
           Last Egress Identifier identifies the Upstream Nickname."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 5 }

   trillOamMepMtvrIngress OBJECT-TYPE
       SYNTAX          Dot1agCfmIngressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Ingress Action Field of
           the MTVR. The value ingNoTlv(0) indicates that no
           Reply Ingress TLV was returned in the MTVM."
       REFERENCE       "RFC 7455 11.2.3"
       ::= { trillOamMtvrEntry 6 }

   trillOamMepMtvrIngressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the ingress MAC address field."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 7 }

   trillOamMepMtvrIngressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is
           determined by the value of the
           trillOamMepMtvrIngressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 8 }

   trillOamMepMtvrIngressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is determined by
           the value of the trillOamMepMtvrIngressPortId object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 9 }

   trillOamMepMtvrEgress OBJECT-TYPE
       SYNTAX          Dot1agCfmEgressActionFieldValue



Kumar et al.             Expires April 14, 2016                [Page 31]


Internet Draft               TRILL OAM MIB              October 12, 2015


       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Egress Action Field of the MTVR.
           The value ingNoTlv(0) indicates that no Reply Egress TLV was
           returned in the MTVR."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 10 }

   trillOamMepMtvrEgressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the egress MAC address field."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 11 }

   trillOamMepMtvrEgressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepMtvrEgressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 12 }

   trillOamMepMtvrEgressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepMtvrEgressPortId object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 13 }

   trillOamMepMtvrChassisIdSubtype OBJECT-TYPE
       SYNTAX          LldpChassisIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "This object specifies the format of the Chassis ID returned
           in the Sender ID TLV of the MTVR, if any.  This value is
           meaningless if the trillOamMepMtvrChassisId has a
           length of 0."
       REFERENCE       "RFC 7455 8.4.1"



Kumar et al.             Expires April 14, 2016                [Page 32]


Internet Draft               TRILL OAM MIB              October 12, 2015


       ::= { trillOamMtvrEntry 14 }

   trillOamMepMtvrChassisId OBJECT-TYPE
       SYNTAX          LldpChassisId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The Chassis ID returned in the Sender ID TLV of the MTVR, if
           any. The format of this object is determined by the
           value of the trillOamMepMtvrChassisIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 15 }

   trillOamMepMtvrOrganizationSpecificTlv OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "All Organization specific TLVs returned in the MTVR, if
           any. Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.1"
       ::= { trillOamMtvrEntry 16 }

   trillOamMepMtvrNextHopNicknames OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next hop Rbridge List TLV returned in the PTR, if
           any. Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.3"
       ::= { trillOamMtvrEntry 17 }

   trillOamMepMtvrReceiverAvailability OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "True value indicates that MTVR response contained
           Multicast receiver availability TLV."
       REFERENCE       "RFC 7455 8.4.10"
       ::= { trillOamMtvrEntry 18 }

   trillOamMepMtvrReceiverCount OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-only



Kumar et al.             Expires April 14, 2016                [Page 33]


Internet Draft               TRILL OAM MIB              October 12, 2015


       STATUS          current
       DESCRIPTION
           "Indicates the number of Multicast receivers available on
           responding RBridge on the VLAN specified by the
           diagnostic VLAN."
       REFERENCE       "RFC 7455 8.4.10"
       ::= { trillOamMtvrEntry 19 }

   -- *****************************************************************
   -- TRILL OAM MEP Database Table
   -- *****************************************************************

   trillOamMepDbTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF TrillOamMepDbEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This table is an extension of the dot1agCfmMepDbTable
           and rows are automatically added to or deleted from
           this table based upon row creation and destruction of the
           dot1agCfmMepDbTable."
       REFERENCE
          "RFC 7455"
       ::= { trillOamMep 5 }

   trillOamMepDbEntry OBJECT-TYPE
       SYNTAX      TrillOamMepDbEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The conceptual row of trillOamMepDbTable."
       AUGMENTS {
                dot1agCfmMepDbEntry
                }
       ::= { trillOamMepDbTable 1 }

   TrillOamMepDbEntry ::= SEQUENCE {
         trillOamMepDbFlowIndex         Unsigned32,
         trillOamMepDbFlowEntropy       OCTET STRING,
         trillOamMepDbFlowState         Dot1agCfmRemoteMepState,
         trillOamMepDbFlowFailedOkTime  TimeStamp,
         trillOamMepDbRbridgeName       Unsigned32,
         trillOamMepDbLastGoodSeqNum    Counter32
       }

   trillOamMepDbFlowIndex OBJECT-TYPE
       SYNTAX        Unsigned32 (1..65535)
       MAX-ACCESS    read-only



Kumar et al.             Expires April 14, 2016                [Page 34]


Internet Draft               TRILL OAM MIB              October 12, 2015


       STATUS        current
       DESCRIPTION
         "This object identifies the Flow. If Flow Identifier TLV
          is received than index received can also be used."
       REFERENCE "RFC 7455"
       ::= {trillOamMepDbEntry 1 }

   trillOamMepDbFlowEntropy OBJECT-TYPE
       SYNTAX        OCTET STRING (SIZE  (96))
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
         "96 byte Flow Entropy."
       REFERENCE "RFC 7455 section 3."
       ::= {trillOamMepDbEntry 2 }

   trillOamMepDbFlowState OBJECT-TYPE
       SYNTAX       Dot1agCfmRemoteMepState
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           "The operational state of the remote MEP (flow based)
            IFF State machines. State Machine is running now per
            flow."
       REFERENCE "RFC 7455"
       ::= {trillOamMepDbEntry 3 }

    trillOamMepDbFlowFailedOkTime OBJECT-TYPE
       SYNTAX        TimeStamp
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           "The Time (sysUpTime) at which the Remote MEP Flow state
            machine last entered either the RMEP_FAILED or RMEP_OK
            state."
       REFERENCE "RFC 7455"
       ::= {trillOamMepDbEntry 4 }

   trillOamMepDbRbridgeName OBJECT-TYPE
       SYNTAX        Unsigned32(0..65471)
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
            "Remote MEP Rbridge Nickname."
       REFERENCE "RFC 7455 RFC 6325 section 3"
       ::= {trillOamMepDbEntry 5 }

   trillOamMepDbLastGoodSeqNum OBJECT-TYPE



Kumar et al.             Expires April 14, 2016                [Page 35]


Internet Draft               TRILL OAM MIB              October 12, 2015


       SYNTAX        Counter32
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
            "Last Sequence Number received."
       REFERENCE "RFC 7455 13.1"
       ::= {trillOamMepDbEntry 6}

   -- ******************************************************************
   -- TRILL OAM MIB NOTIFICATIONS (TRAPS)
   -- This notification is sent to management entity whenever a
   -- MEP loses/restores
   -- contact with its peer Flow Meps
   -- ******************************************************************
   trillOamFaultAlarm NOTIFICATION-TYPE
       OBJECTS         { trillOamMepDbFlowState }
       STATUS          current
       DESCRIPTION
           "A MEP Flow has a persistent defect condition.
            A notification (fault alarm) is sent to the management
            entity with the OID of the Flow that has detected the fault.

           The management entity receiving the notification can identify
           the system from the network source address of the
           notification, and can identify the Flow reporting the defect
           by the indices in the OID of the trillOamMepFlowIndex, and
           trillOamFlowDefect variable in the notification:

              dot1agCfmMdIndex - Also the index of the MEP's
                                 Maintenance Domain table entry
                                 (dot1agCfmMdTable).
              dot1agCfmMaIndex - Also an index (with the MD table index)
                                 of the MEP's Maintenance Association
                                 network table entry
                                 (dot1agCfmMaNetTable), and (with the MD
                                 table index and component ID) of the
                                 MEP's MA component table entry
                                 (dot1agCfmMaCompTable).
              dot1agCfmMepIdentifier - MEP Identifier and final index
                                 into the MEP table (dot1agCfmMepTable).
              trillOamMepFlowCfgIndex - Index identifies
                                 indicates the specific Flow for
                                 the MEP"
       REFERENCE       "RFC 7455"
      ::= { trillOamNotifications 1 }

   -- ******************************************************************
   -- TRILL OAM MIB Module - Conformance Information



Kumar et al.             Expires April 14, 2016                [Page 36]


Internet Draft               TRILL OAM MIB              October 12, 2015


   -- ******************************************************************

   trillOamMibCompliances  OBJECT IDENTIFIER
       ::= { trillOamMibConformance 1 }

   trillOamMibGroups  OBJECT IDENTIFIER
       ::= { trillOamMibConformance 2 }


   -- ******************************************************************
   -- TRILL OAM MIB Units of conformance
   -- ******************************************************************

   trillOamMepMandatoryGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepRName,
                           trillOamMepNextPtmTId,
                           trillOamMepNextMtvmTId,
                           trillOamMepPtrIn,
                           trillOamMepPtrInOutofOrder,
                           trillOamMepPtrOut,
                           trillOamMepMtvrIn,
                           trillOamMepMtvrInOutofOrder,
                           trillOamMepMtvrOut,
                           trillOamMepTxLbmDestRName,
                           trillOamMepTxLbmHC,
                           trillOamMepTxLbmReplyModeOob,
                           trillOamMepTransmitLbmReplyIp,
                           trillOamMepTxLbmFlowEntropy,
                           trillOamMepTxPtmDestRName,
                           trillOamMepTxPtmHC,
                           trillOamMepTxPtmReplyModeOob,
                           trillOamMepTransmitPtmReplyIp,
                           trillOamMepTxPtmFlowEntropy,
                           trillOamMepTxPtmStatus,
                           trillOamMepTxPtmResultOK,
                           trillOamMepTxPtmMessages,
                           trillOamMepTxPtmSeqNumber,
                           trillOamMepTxMtvmTree,
                           trillOamMepTxMtvmHC,
                           trillOamMepTxMtvmReplyModeOob,
                           trillOamMepTransmitMtvmReplyIp,
                           trillOamMepTxMtvmFlowEntropy,
                           trillOamMepTxMtvmStatus,
                           trillOamMepTxMtvmResultOK,
                           trillOamMepTxMtvmMessages,
                           trillOamMepTxMtvmSeqNumber,
                           trillOamMepTxMtvmScopeList,



Kumar et al.             Expires April 14, 2016                [Page 37]


Internet Draft               TRILL OAM MIB              October 12, 2015


                           trillOamMepDiscontinuityTime
                       }
       STATUS          current
       DESCRIPTION
           "Mandatory objects for the TRILL OAM MEP group."
       ::= { trillOamMibGroups 1 }

   trillOamMepFlowCfgTableGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepFlowCfgFlowEntropy,
                           trillOamMepFlowCfgDestRName,
                           trillOamMepFlowCfgFlowHC,
                           trillOamMepFlowCfgRowStatus
                       }
       STATUS          current
       DESCRIPTION
           "TRILL OAM MEP Flow Configuration objects group."
       ::= { trillOamMibGroups 2 }

   trillOamPtrTableGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepPtrHC,
                           trillOamMepPtrFlag,
                           trillOamMepPtrErrorCode,
                           trillOamMepPtrTerminalMep,
                           trillOamMepPtrLastEgressId,
                           trillOamMepPtrIngress,
                           trillOamMepPtrIngressMac,
                           trillOamMepPtrIngressPortIdSubtype,
                           trillOamMepPtrIngressPortId,
                           trillOamMepPtrEgress,
                           trillOamMepPtrEgressMac,
                           trillOamMepPtrEgressPortIdSubtype,
                           trillOamMepPtrEgressPortId,
                           trillOamMepPtrChassisIdSubtype,
                           trillOamMepPtrChassisId,
                           trillOamMepPtrOrganizationSpecificTlv,
                           trillOamMepPtrNextHopNicknames
                       }
       STATUS          current
       DESCRIPTION
           "TRILL OAM MEP PTR objects group."
       ::= { trillOamMibGroups 3 }

   trillOamMtvrTableGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepMtvrFlag,
                           trillOamMepMtvrErrorCode,



Kumar et al.             Expires April 14, 2016                [Page 38]


Internet Draft               TRILL OAM MIB              October 12, 2015


                           trillOamMepMtvrLastEgressId,
                           trillOamMepMtvrIngress,
                           trillOamMepMtvrIngressMac,
                           trillOamMepMtvrIngressPortIdSubtype,
                           trillOamMepMtvrIngressPortId,
                           trillOamMepMtvrEgress,
                           trillOamMepMtvrEgressMac,
                           trillOamMepMtvrEgressPortIdSubtype,
                           trillOamMepMtvrEgressPortId,
                           trillOamMepMtvrChassisIdSubtype,
                           trillOamMepMtvrChassisId,
                           trillOamMepMtvrOrganizationSpecificTlv,
                           trillOamMepMtvrNextHopNicknames,
                           trillOamMepMtvrReceiverAvailability,
                           trillOamMepMtvrReceiverCount
                       }
       STATUS          current
       DESCRIPTION
           "TRILL OAM MEP MTVR objects group."
       ::= { trillOamMibGroups 4 }

   trillOamMepDbGroup  OBJECT-GROUP
       OBJECTS   {
         trillOamMepDbFlowIndex,
         trillOamMepDbFlowEntropy,
         trillOamMepDbFlowState,
         trillOamMepDbFlowFailedOkTime,
         trillOamMepDbRbridgeName,
         trillOamMepDbLastGoodSeqNum
       }

       STATUS      current
       DESCRIPTION
          "TRILL OAM MEP DB objects group."
       ::= { trillOamMibGroups 5 }

   trillOamNotificationGroup NOTIFICATION-GROUP
       NOTIFICATIONS  { trillOamFaultAlarm }
       STATUS current
       DESCRIPTION
           "A collection of objects describing notifications(traps)."
       ::= { trillOamMibGroups 6 }

   -- ******************************************************************
   -- TRILL OAM MIB Module Compliance statements
   -- ******************************************************************

   trillOamMibCompliance MODULE-COMPLIANCE



Kumar et al.             Expires April 14, 2016                [Page 39]


Internet Draft               TRILL OAM MIB              October 12, 2015


       STATUS          current
       DESCRIPTION
           "The compliance statement for the TRILL OAM MIB."
       MODULE          -- this module
       MANDATORY-GROUPS {
                           trillOamMepMandatoryGroup,
                           trillOamMepFlowCfgTableGroup,
                           trillOamPtrTableGroup,
                           trillOamMtvrTableGroup,
                           trillOamMepDbGroup,
                           trillOamNotificationGroup
                       }
       ::= { trillOamMibCompliances 1 }

   -- Compliance requirement for read-only implementation.

   trillOamMibReadOnlyCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "Compliance requirement for implementation that only
            provide read-only support for TRILL-OAM-MIB.
            Such devices can be monitored but cannot be configured
            using this MIB module."
       MODULE -- this module
       MANDATORY-GROUPS {
                           trillOamMepMandatoryGroup,
                           trillOamMepFlowCfgTableGroup,
                           trillOamPtrTableGroup,
                           trillOamMtvrTableGroup,
                           trillOamMepDbGroup,
                           trillOamNotificationGroup
                         }
       -- trillOamMepTable

       OBJECT trillOamMepTxLbmDestRName
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxLbmHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxLbmReplyModeOob
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."



Kumar et al.             Expires April 14, 2016                [Page 40]


Internet Draft               TRILL OAM MIB              October 12, 2015


       OBJECT trillOamMepTransmitLbmReplyIp
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxLbmFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmDestRName
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmReplyModeOob
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTransmitPtmReplyIp
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmStatus
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmResultOK
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmMessages
       MIN-ACCESS  read-only
            DESCRIPTION



Kumar et al.             Expires April 14, 2016                [Page 41]


Internet Draft               TRILL OAM MIB              October 12, 2015


                "Write access is not required."

       OBJECT trillOamMepTxPtmSeqNumber
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmTree
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmReplyModeOob
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTransmitMtvmReplyIp
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmStatus
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmResultOK
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmMessages
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmSeqNumber



Kumar et al.             Expires April 14, 2016                [Page 42]


Internet Draft               TRILL OAM MIB              October 12, 2015


       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmScopeList
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."


   -- trillOamMepFlowCfgTable

       OBJECT trillOamMepFlowCfgFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepFlowCfgDestRName
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepFlowCfgFlowHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepFlowCfgRowStatus
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."


       ::= { trillOamMibCompliances 2 }


   END



8. Security Considerations

   This MIB relates to a system that will provide network connectivity
   and packet forwarding services. As such, improper manipulation of the
   objects represented by this MIB may result in denial of service to a
   large number of end-users.

   There are number of management objects defined in this MIB module



Kumar et al.             Expires April 14, 2016                [Page 43]


Internet Draft               TRILL OAM MIB              October 12, 2015


   with a MAX-ACCESS clause of read-create. Such objects may be
   considered sensitive or vulnerable in some network environments.
   Support for SET operations in a non-secure environment without proper
   protection can have negative effect on sensitivity/vulnerability:

   The following table and objects in the TRILL-OAM-MIB can be
   manipulated to interfere with the operation of RBridges by causing
   cpu use spikes:

   o trillOamMepTransmitLbmReplyIp allows the reply from a Loopback
   message to be transmitted to an IP address in the TLV thus allowing
   replies to be sent to any system to cause Denial of Service.

   o trillOamMepTransmitPtmReplyIp allows the reply from a Path Trace
   message to be transmitted to an IP address in the TLV and thus
   allowing replies to be sent to any system to cause Denial of Service.

   o trillOamMepTxPtmMessages allows the generation of PTM Messages and
   can be used to generate lots of cpu driven traffic.

   o trillOamMepTransmitMtvmReplyIp allows from reply from an MTV
   message to be transmitted to an IP address in the TLV and thus
   allowing replies to be sent to any system to cause Denial of
   Service.

   o trillOamMepTxMtvmMessages allows the generation of MTV Messages and
   can be used to generate lots of cpu driven traffic.

   The following objects in the TRILL-OAM-MIB are read-create and can be
   manipulated to interfere with the OAM operations of RBridges. If the
   number of OAM frames generated in the network is high, this can cause
   a cpu spike on destination Rbridges if Control plane policing is not
   properly implemented or configured on destination Rbridges.

   o trillOamMepTxLbmHC is used to set the Maximum Hop count for the LBM
   message. As OAM frame don't leak out of the TRILL network, it has no
   side effects.

   o trillOamMepTxLbmReplyModeOob is used to indicate whether the reply
   is in-band or out-of-band. This object's vulnerability is covered as
   part of trillOamMepTransmitLbmReplyIp.

   o trillOamMepTxLbmFlowEntropy is used to indicate the customer flow
   and find the exact path in the network. The creation of valid flows
   is its intended purpose. If invalid flows are created on vulnerable
   system they will be dropped in forwarding.

   o trillOamMepTxLbmDestRName is read-create but it's not vulnerable as



Kumar et al.             Expires April 14, 2016                [Page 44]


Internet Draft               TRILL OAM MIB              October 12, 2015


   invalid-name routes won't be present and will be rejected by the OAM
   application as part of normal processing.

   o trillOamMepTxPtmHC is used to set the Maximum Hop count for the PTM
   message. As OAM frame don't leak out of the TRILL network, it has no
   side effect.

   o trillOamMepTxPtmReplyModeOob is used to indicate whether the reply
   is in-band or out-of-band. This object's vulnerability is covered as
   part of trillOamMepTransmitPtmReplyIp.

   o trillOamMepTxPtmFlowEntropy is used to indicate the customer flow
   and find the exact path in the network. Creation of valid flows is
   its intended purpose. If invalid flows are created on vulnerable
   systems they will be dropped in forwarding.

   o trillOamMepTxPtmDestRName is read-create but it's not vulnerable as
   invalid-name routes won't be present and will be rejected by the OAM
   application as part of normal processing.

   o trillOamMepTxPtmStatus is required for normal PTM operation.

   o trillOamMepTxPtmResultOK is required for normal PTM operation.

   o trillOamMepTxPtmSeqNumber is required for normal PTM operation.

   o trillOamMepTxPtmMessages is required for normal PTM operation.

   o trillOamMepTxMtvmTree is required for normal MTVM operation.

   o trillOamMepTxMtvmHC is used to set the Maximum Hop count for the
   MTVM message. As OAM frame don't leak out of the TRILL network, it
   has no side effect

   o trillOamMepTxMtvmReplyModeOob is used to indicate whether the reply
   is in-band or out-of-band. This object's vulnerability is covered as
   part of trillOamMepTransmitMtmReplyIp

   o trillOamMepTxMtvmFlowEntropy is used to indicate the customer flow
   and find the exact path in the network. Creation of valid flows is
   its intended purpose. If invalid flows are created on vulnerable
   systems they will be dropped in forwarding.

   o trillOamMepTxMtvmStatus is required for normal MTVM operation.

   o trillOamMepTxMtvmResultOK, trillOamMepTxMtvmMessages,
   trillOamMepTxMtvmSeqNumber, and trillOamMepTxMtvmScopeList is
   required for normal MTVM operation.



Kumar et al.             Expires April 14, 2016                [Page 45]


Internet Draft               TRILL OAM MIB              October 12, 2015


   trillOamMepTransmitLbmReplyIp, trillOamMepTransmitPtmReplyIp, and
   trillOamMepTransmitMtvmReplyIp allow setting of the IP address to
   which reports are sent and thus it can be used for Denial of Service
   for that IP.

   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments. It is thus important to
   control GET and/or NOTIFY access to these objects and possibly to
   encrypt the values of these objects when sending them over the
   network via SNMP. For example, Path Trace messages expose the unicast
   topology of the network and Multi-destination Tree Verification
   Messages expose the multicast tree topology of the network. This
   information should not be available to all users of the network.

   SNMP versions prior to SNMPv3 did not include adequate security. Even
   if the network itself is secure (for example by using IPsec), there
   is no control as to who on the secure network is allowed to access
   and GET/SET (read/change/create/delete) the objects in this MIB
   module.

   Implementation should provide the security features described by
   SNMPv3 framework (see [RFC3410]), and implementations claiming
   compliance to the SNMPv3 standard MUST include full support for
   authentication and privacy via the User-based Security Model
   (USM)[RFC3414] with the AES cipher algorithm [RFC3826].
   Implementations MAY also provide support for the Transport Security
   Model (TSM) [RFC5591] in combination with a secure transport such as
   SSH [RFC5592] or TLS/DTLS [RFC6353].

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED. Instead, deployment of SNMPv3 with cryptographic
   security enabled is RECOMMENDED. It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give only those
   principals (users) that have legitimate rights to indeed GET or SET
   (change/create/delete) access to the objects.


9. IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER value recorded in the SMI Numbers registry:

   Descriptor   OBJECT   IDENTIFIER  value
   ----------------------------------------
   trillOamMIB  { mib-2 xxx }




Kumar et al.             Expires April 14, 2016                [Page 46]


Internet Draft               TRILL OAM MIB              October 12, 2015


   Editor's Note (to be removed prior to publication): the IANA is
   requested to assign a value for "xxx" under the 'mib-2' subtree and
   to record the assignment in the SMI Numbers registry. When the
   assignment has been made, the RFC Editor is asked to replace "XXX"
   (here and in the MIB module) with the assigned value and to remove
   this note.

10.  Contributors

   We wish to thank members of the IETF TRILL WG and the MIB-Doctor for
   their comments and suggestions. Detailed comments were provided by
   Sam Aldrin, Donald Eastlake, Tom Taylor, and Harrie Hazewinkel.

11.  References
11.1.  Normative References


              [RFC2119] Bradner, S., "Key words for use in RFCs to
              Indicate Requirement Levels", BCP 14, RFC 2119, March
              1997.

              [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Structure of Management Information
              Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

              [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD
              58, RFC 2579, April 1999.

              [RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Conformance Statements for SMIv2",
              STD 58, RFC 2580, April 1999.

              [RFC6325] Perlman, R., Eastlake 3rd, D., Dutt, D., Gai,
              S., and A. Ghanwani, "Routing Bridges (RBridges): Base
              Protocol Specification", RFC 6325, July 2011.

              [RFC7172] Eastlake 3rd, D., Zhang, M., Agarwal, P.,
              Perlman, R., and D. Dutt, "Transparent Interconnection of
              Lots of Links (TRILL): Fine-Grained Labeling", RFC 7172,
              May 2014.

              [RFC7455] Senevirathne, T., et.al., "Transparent
              Interconnection of Lots of Links (TRILL): Fault
              Management", March 2015.

              [LLDP-MIB] IEEE,
              http://www.ieee802.org/1/files/public/MIBs/LLDP-MIB-



Kumar et al.             Expires April 14, 2016                [Page 47]


Internet Draft               TRILL OAM MIB              October 12, 2015


              200505060000Z.txt

              [802.1Q] IEEE, "IEEE Standard for Local and metropolitan
              area networks - Media Access Control (MAC) Bridges and
              Virtual Bridge Local Area Networks", IEEE Std 802.1Q-2011,
              31 August 2011.



11.2.  Informative References


              [RFC3410] Case, J., Mundy, R., Partain, D., and B.Stewart,
              "Introduction and Applicability Statements for Internet-
              Standard Management Framework", RFC 3410, December 2002.

              [RFC6905] Senevirathne, T., Bond, D., Aldrin, S., Li, Y.,
              and R. Watve, "Requirements for Operations,
              Administration, and Maintenance (OAM) in Transparent
              Interconnection of Lots of Links (TRILL)", RFC 6905, March
              2013.

              [RFC7174] Salam, S., Senevirathne, T., Aldrin, S., and D.
              Eastlake 3rd, "Transparent Interconnection of Lots of
              Links (TRILL) Operations, Administration, and Maintenance
              (OAM) Framework", RFC 7174, May 2014.


              Authors' Addresses

                 Deepak Kumar
                 Cisco
                 510 McCarthy Blvd,
                 Milpitas, CA 95035, USA
                 Phone : +1 408-853-9760
                 Email: dekumar@cisco.com


                 Samer Salam
                 Cisco
                 595 Burrard St. Suite 2123
                 Vancouver, BC V7X 1J1, Canada
                 Email: ssalam@cisco.com


                 Tissa Senevirathne
                 Consultant
                 Email: tsenevir@gmail.com



Kumar et al.             Expires April 14, 2016                [Page 48]


Internet Draft               TRILL OAM MIB              October 12, 2015





















































Kumar et al.             Expires April 14, 2016                [Page 49]