Network Working Group R. R. Stewart
INTERNET-DRAFT M. A. Ramalho
Cisco Systems
Q. Xie
Motorola
M. Tuexen
Siemens AG
I. Rytina
Ericsson
P. Conrad
Temple University
expires in six months May 7, 2001
SCTP Dynamic Addition of IP addresses
<draft-ietf-tsvwg-addip-sctp-00.txt>
Status of This Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC 2026 [RFC2026]. Internet-Drafts are
working documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document describes extensions to the Stream Control
Transmission Protocol (SCTP) [RFC2960] that provide a method to
reconfigure IP address information on an existing association or
to request that a peer set a stream flow limit.
TABLE OF CONTENTS
1. Introduction............................................... 2
2. Conventions................................................ 3
3. Additional Chunks and Parameters........................... 3
3.1 New Chunk Types........................................... 3
3.1.1 Address Configuration Change Chunk (ASCONF)............ 3
3.1.2 Address Configuration Acknowledgment Chunk (ASCONF-ACK)
3.2 New Parameter Types....................................... 4
3.2.1 Add IP Address.......................................... 6
3.2.2 Delete IP Address....................................... 6
3.2.3 Stream Flow Limit Change................................ 7
3.2.4 Error Cause Indication.................................. 7
3.2.5 Set Primary IP Address.................................. 8
Stewart et.al. [Page 1]
Internet Draft Address/Stream Configuration May 2001
3.2.6 Success Indication...................................... 8
3.3 New Error Causes.......................................... 9
3.3.1 Error Cause: Request to Delete Last remaining IP Address 9
3.3.2 Error Cause: Operation Refused due to Resource Shortage.10
3.3.3 Error Cause: Request to Delete Source IP Address........10
4. Procedures.................................................11
4.1 ASCONF Chunk Procedures...................................11
4.1.1 Congestion Control of ASCONF Chunks.....................12
4.2 Upon reception of a ASCONF Chunk..........................13
4.3 General rules for address manipulation....................15
4.3.1 A special case for OOTB ABORT chunks....................17
4.4 Setting of the primary address............................18
4.5 Steam Flow Limit Procedures...............................18
4.5.1 Stream Receiver side procedures.........................19
4.5.2 Stream Sender side procedures...........................19
4.5.3 ULP considerations on the use of SCTP flow limit
facility................................................20
5. Security Considerations....................................20
6. IANA considerations........................................20
7. Authors' Addresses.........................................20
8. References.................................................21
1. Introduction
To extend the utility and application senarios of SCTP, this
document introduces optional extensions that provide SCTP with the
ability to reconfigure IP address information on an existing
association or to request the peer set a stream flow limit.
These extensions enable SCTP to be utilized in the following
applications:
- Dynamic IP addresses added and subtracted extension: For
computational or networking platforms that allow addition/removal of
physical interface cards this feature can provide:
A) a graceful method to add to the interfaces of an existing
association. For the multi-homed IPv6 case this feature will
allow renumbering of existing associations.
B) provides a method for an endpoint to request that its peer set
its primary destination address: This can be useful
when an address is about to be deleted. Or when an endpoint
has some predetermined knowledge about which is the
preferred address to receive SCTP packets upon.
- The SCTP flow limit extension: This extension enables the
ability to request a sender to set a limit to the
outstanding data sent to each stream. This in turn will
provide:
A) The ability to minimize the occurrence of a single stream
monopolizing all transport level resources (e.g. a_rwnd
Stewart et.al. [Page 2]
Internet Draft Address/Stream Configuration May 2001
"deadlock").
B) The ability to dynamically change the stream buffering
limits as the application deems appropriate at any particular
instant.
2. Conventions
The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
SHOULD NOT, RECOMMENDED, NOT RECOMMENDED, MAY, and OPTIONAL, when
they appear in this document, are to be interpreted as described in
RFC 2119 [RFC2119].
3. Additional Chunks and Parameters
This section describes the addition of two new chunks and, six
new parameters to allow:
- Dynamic addition of IP Addresses to an association.
- Dynamic deletion of IP Addresses to an association.
- A request to set the primary address the peer will
use when sending to an endpoint.
- The setting of stream flow limits.
Additionally, this section describes three new error causes that
support these new chunks and parameters.
3.1 New Chunk Types
This section defines two new Chunk types that will be used to
transfer the control information reliably. Table 1 illustrates the two
new chunk types.
Chunk Type Chunk Name
--------------------------------------------------------------
11000001 Address/Stream Configuration Change Chunk (ASCONF)
10000000 Address Configuration Acknowledgment (ASCONF-ACK)
Table 1: Address/Stream Configuration Chunks
It should be noted that the ASCONF Chunk format requires the
receiver to report to the sender if it does not understand the
ASCONF chunk. This is accomplished by setting the upper bits in the
Chunk type as described in [RFC2960] section 3.2. Note that the
upper two bits in the ASCONF chunk are set to one. As defined in
[RFC2960] section 3.2, setting these upper bits in this manner will
cause the receiver that does not understand this chunk to skip the
chunk and continue processing, but report in an Operation Error
Chunk using the 'Unrecognized Chunk Type' cause of error.
3.1.1 Address Configuration Change Chunk (ASCONF)
This chunk is used to communicate to the remote endpoint one of the
Stewart et.al. [Page 3]
Internet Draft Address/Stream Configuration May 2001
configuration change requests that MUST be acknowledged. The
information carried in the ASCONF chunk is always in the form of a
Tag-Length-Value (TLV) as described in "3.2.1
Optional/Variable-length Parameter Format" in [RFC2960].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC1 | Chunk Flags | Chunk Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Serial Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ \
/ .... /
\ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID #N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter #N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Serial Number : 32 bits (unsigned integer)
This value represents a Serial Number for the ASCONF Chunk. The
valid range of Serial Number is from 0 to 4294967295 (2**32 - 1).
Serial Numbers wrap back to 0 after reaching 4294967295.
ASCONF-Request Correlation ID: 32 bits (unsigned integer)
This is an opaque integer assigned by the sender to identify each
request parameter. It is in host byte order and is only meaningful
to the sender. The receiver of the ASCONF chunk will copy this 32
bit value into the ASCONF Correlation ID field of the
ASCONF-ACK. The sender of the ASCONF can use this same value in the
ASCONF-ACK to find which request the response is for.
ASCONF Parameter: TLV format
Each Address configuration change is represented by a TLV
parameter has defined in Section 3.2. One or more request
may be present in a ASCONF chunk.
3.1.2 Address Configuration Acknowledgment Chunk (ASCONF-ACK)
This chunk is used by the receiver of an ASCONF chunk to acknowledge
its reception. It carries zero or more results for any ASCONF
Parameters that were processed by the receiver.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
Stewart et.al. [Page 4]
Internet Draft Address/Stream Configuration May 2001
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x80 | Chunk Flags | Chunk Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Serial Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter Response#1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ \
/ .... /
\ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID #N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter Response#N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Serial Number : 32 bits (unsigned integer)
This value represents the Serial Number for the ASCONF chunk that
was received to which this Chunk is acknowledgment of. This value is
copied from the received ASCONF chunk.
ASCONF-Request Correlation ID: 32 bits (unsigned integer)
This value is copied from the ASCONF Correlation ID received in the
ASCONF chunk. It is used by the receiver of the ASCONF-ACK to identify
which ASCONF parameter this response is associated with.
ASCONF Parameter Response : TLV format
The ASCONF Parameter Response is used in the ASCONF-ACK to report
status of ASCONF processing. By default, if a responding endpoint
does not include any Error cause a success is indicated. Thus a
sender of a ASCONF-ACK MAY indicate complete success of all TLV's in
a ASCONF by returning only the Chunk Type, Chunk Flags, Chunk Length
(set to 8) and the Serial Number.
3.2 New Parameter Types
The six new parameters added follow the format defined in section
3.2.1 of [RFC2960]. Table 2 describes the Parameters.
Address Configuration Parameters Parameter Type
-------------------------------------------------
Add IP Address 49153 (0xC001)
Delete IP Address 49154 (0xC002)
Stream Flow limit Request 49155 (0xC003)
Error Cause Indication 49156 (0xC004)
Set Primary Address 49157 (0xC005)
Success report 49158 (0xC006)
Table 2: Address Configuration Parameters
Stewart et.al. [Page 5]
Internet Draft Address/Stream Configuration May 2001
3.2.1 Add IP Address
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC001 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address Parameter: TLV
This field contains an IPv4 or IPv6 address parameter as described
in 3.3.2.1 of RFC2960. The complete TLV is wrapped within this
parameter. It informs the receiver that the Address specified is to
be added to the existing association.
An example TLV requesting that the IPv4 address 10.1.1.1 should be
made the primary destination address would look as follows:
+--------------------------------+
| Type=0xC001 | Length = 12 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
Valid Chunk Appearance
The Add IP Address parameter may only appear in the ASCONF chunk
type.
3.2.2 Delete IP Address
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type =0xC002 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address Parameter: TLV
This field contains an IPv4 or IPv6 address parameter as described in
3.3.2.1 of [RFC2960]. The complete TLV is wrapped within this
parameter. It informs the receiver that the Address specified is to
be removed from the existing association.
An example TLV deleting the IPv4 address 10.1.1.1 from an existing
association would look as follows:
Stewart et.al. [Page 6]
Internet Draft Address/Stream Configuration May 2001
+--------------------------------+
| Type=0xC002 | Length = 12 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
Valid Chunk Appearance
The Delete IP Address parameter may only appear in the ASCONF chunk
type.
3.2.3 Stream Flow Limit Change
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type =0xC003 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Stream Number 1 | Flow Limit 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ /
/ \
\ /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Stream Number N | Flow Limit N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Stream Number n : 16 bits (unsigned integer)
This is the stream number that is requesting a limit be placed
on the sender based on the applications receive buffer sizes.
Flow Limit n : 16 bits (unsigned integer)
This is the limit the receiver is requesting (in bytes) as to the
maximum amount of data that the receiver may accept. Note that the
value 0 holds a special meaning described in Section 4.5.
Valid Chunk Appearance
The Stream Flow Limit Change parameter may only appear in the ASCONF
chunk type.
3.2.4 Error Cause Indication
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC004 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Stewart et.al. [Page 7]
Internet Draft Address/Stream Configuration May 2001
| Error Cause(s) or Return Info on Success |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
When reporting an error this response parameter is used to wrap
one or more standard error causes normally found within an SCTP
Operational Error or SCTP Abort (as defined in [RFC2960]). The
Error Cause(s) follow the format defined in section 3.3.10 of
[RFC2960].
Valid Chunk Appearance
The Error Cause Indication parameter may only appear in the
ASCONF-ACK chunk type.
3.2.5 Set Primary IP Address
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type =0xC005 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address Parameter: TLV
This field contains an IPv4 or IPv6 address parameter as described in
3.3.2.1 of [RFC2960]. The complete TLV is wrapped within this
parameter. It requests the receiver to mark the specified address
as the primary address to send data to (see section 5.1.2 of
[RFC2960]). The receiver MAY mark this as its primary upon
receiving this request.
An example TLV requesting that the IPv4 address 10.1.1.1 be made the
primary destination address would look as follows:
+--------------------------------+
| Type=0xC005 | Length = 12 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
Valid Chunk Appearance
The Set Primary IP Address parameter may appear in the ASCONF chunk,
the INIT, or the INIT-ACK chunk type. The inclusion of this parameter
in the INIT or INIT-ACK can be used to indicate an initial preference
of primary address.
3.2.6 Success Indication
Stewart et.al. [Page 8]
Internet Draft Address/Stream Configuration May 2001
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC006 | Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
By default if a responding endpoint does not report an error for any
requested TLV, a success is implicitly indicated. Thus a sender of a
ASCONF-ACK MAY indicate complete success of all TLV's in a ASCONF by
returning only the Chunk Type, Chunk Flags, Chunk Length (set to 8)
and the Serial Number.
The responding endpoint MAY also choose to explicitly report a
success for a requested TLV, by returning a success report ASCONF
Parameter Response.
Valid Chunk Appearance
The Success Indication parameter may only appear in the ASCONF-ACK
chunk type.
3.3 New Error Causes
Three new Error Causes are added to the SCTP Operational Errors,
primarily for use in the ASCONF-ACK chunk.
Cause Code
Value Cause Code
--------- ----------------
12 Request to delete last remaining IP address.
13 Operation Refused due to resource shortage.
14 Request to delete source IP address.
Table 3: New Error Causes
3.3.1 Error Cause: Request to Delete Last remaining IP Address
Cause of error
---------------
Request to delete last remaining IP address: The receiver of this
error sent a request to delete the last IP address from its
association with its peer. This error indicates that the request is
rejected.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=12 | Cause Length=Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ TLV-Copied-From-ASCONF /
/ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Stewart et.al. [Page 9]
Internet Draft Address/Stream Configuration May 2001
An example of a failed delete in an Error Cause TLV would look as
follows in the response ASCONF-ACK message:
+--------------------------------+
| Type = 0xC004 | Length = 20 |
+--------------------------------+
| Cause=12 | Length = 16 |
+----------------+---------------+
| Type= 0xC002 | Length = 12 |
+----------------+---------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
3.3.2 Error Cause: Operation Refused due to Resource Shortage
Cause of error
---------------
This error cause is used to report a failure by the receiver to
perform the requested operation due to a lack of resources. The
entire TLV that is refused is copied from the ASCONF-REQ into the
error cause.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=13 | Cause Length=Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ TLV-Copied-From-ASCONF /
/ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An example of a failed addition in an Error Cause TLV would look as
follows in the response ASCONF-ACK message:
+--------------------------------+
| Type = 0xC004 | Length = 20 |
+--------------------------------+
| Cause=13 | Length = 16 |
+----------------+---------------+
| Type=0xC001 | Length = 12 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
3.3.3 Error Cause: Request to Delete Source IP Address
Cause of error
---------------
Request to delete source IP address: The receiver of this error sent
Stewart et.al. [Page 10]
Internet Draft Address/Stream Configuration May 2001
a request to delete the source IP address of the ASCONF
message. This error indicates that the request is rejected.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=14 | Cause Length=Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ TLV-Copied-From-ASCONF /
/ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An example of a failed delete in an Error Cause TLV would look as
follows in the response ASCONF-ACK message:
+--------------------------------+
| Type = 0xC004 | Length = 20 |
+--------------------------------+
| Cause=14 | Length = 16 |
+----------------+---------------+
| Type=0xC002 | Length = 12 |
+----------------+---------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
IMPLEMENTATION NOTE: It is unlikely that an endpoint would source
a packet from the address being deleted, unless the endpoint
does not do proper source address selection.
4. Procedures
This section will lay out the specific procedures for address/stream
configuration change chunk type and its processing.
4.1 ASCONF Chunk Procedures
When an endpoint has an ASCONF signaled change to be sent to the
remote endpoint it should do the following:
A1) Create a ASCONF Chunk as defined in section 3.1.1. The chunk
should contain all of the TLV('s) of information necessary to be
sent to the remote endpoint, and unique correlation identities for
each request.
A2) A serial number should be assigned to the Chunk. The serial
number should be a monotonically increasing number. All serial
numbers are defined to be initialized at the start of the
association to the same value as the Initial TSN.
A3) If no ASCONF chunk is outstanding (un-acknowledged) with the
remote peer AND there is less than cwnd bytes of user data
Stewart et.al. [Page 11]
Internet Draft Address/Stream Configuration May 2001
outstanding send the chunk.
A4) Start a T-4 RTO timer, using the RTO value of the selected
destination address (normally the primary path see [RFC2960] section
6.4 for details).
A5) When the ASCONF-ACK which acknowledges the serial number last
sent arrives, stop the T-4 RTO timer and clear the appropriate
association and destination error counters as defined in [RFC2960]
section 8.1 and 8.2.
A6) Process all of the TLV's within the ASCONF-ACK to find out
particular status information returned to the various requests that
were sent. Use the Correlation IDs to correlate the request and the
responses.
A7) If an error response is received to a TLV whose parameter type
all TLVs with no response before the failed TLV are considered
successful if not reported. All TLVs after the failed response are
considered unsuccessful unless a specific success indication is
present for the parameter.
A8) If there are no responses to TLVs whose parameter type begins
all TLVs not responded to are considered successful.
If the T-4 RTO timer expires the endpoint should do the following:
B1) Increment the error counter and perform path failure detection
on the appropriate destination address as defined in [RFC2960]
section 8.2.
B2) Increment the association error counter and perform endpoint
failure detection on the association as defined in [RFC2960] section
8.1.
B3) Back-off the destination address RTO timer to which the ASCONF
chunk was sent.
B4) Re-transmit the ASCONF chunk last sent and if possible choose an
alternate destination address (please refer to [RFC2960] section
6.4.1). An endpoint MUST NOT add new parameters to this chunk, it
MUST be the same (including its serial number) as the last ASCONF
sent.
B5) Restart the T-4 RTO timer. Note if a different destination is
selected, then the RTO used will be that of the new destination
address.
Note: That the the total number of re-transmissions is limited by B2
above. If the maximum is reached the association will fail and enter
a CLOSED state (see [RFC2960] section 6.4.1 for details).
4.1.1 Congestion Control of ASCONF Chunks
Stewart et.al. [Page 12]
Internet Draft Address/Stream Configuration May 2001
In defining the ASCONF chunk transfer procedures it is essential
that these transfers MUST NOT cause congestion within the network.
To achieve this we place these restrictions on the transfer of
ASCONF chunks:
R1) One and only one ASCONF Chunk MAY be in transit and
unacknowledged at any one time. If a sender, after sending a ASCONF
chunk, decides it needs to transfer another ASCONF Chunk, it MUST
wait until the ASCONF-ACK Chunk returns from the previous ASCONF
Chunk before sending a subsequent ASCONF. Note this restriction
binds each side, so at any time two ASCONF may be in-transit on any
given association (one sent from each endpoint).
R2) A ASCONF MUST NOT be sent if there is no room in the current
cwnd. If there is room in the cwnd of the destination network the
Chunk may be sent regardless of the value of rwnd.
R3) A ASCONF may be bundled with any other Chunk type except other
ASCONF chunks.
R4) A ASCONF-ACK may be bundled with any other Chunk type except
other ASCONF-ACK's.
R5) Both ASCONF and ASCONF-ACK chunks MUST NOT be sent in any SCTP
state except ESTABLISHED.
R6) An ASCONF and respective ASCONF-ACK MUST NOT be larger than the
path MTU of the destination.
If the sender of a ASCONF chunk receives a Operational Error
indicating that the ASCONF chunk type is not understood, then the
sender MUST not send subsequent ASCONF chunks to the peer. The
endpoint should also inform the upper level application that the
peer endpoint does not support any of the extensions detailed in this
document.
4.2 Upon reception of a ASCONF Chunk.
When an endpoint receives a ASCONF chunk from the remote peer it
should perform the following:
C1) Compare the value of the serial number to the value the endpoint
stored in a new association variable 'Peer-Serial-Number'. This
value MUST be initialized to the Initial TSN value minus 1.
C2) If the value found in the serial number is equal to the the
('Peer-Serial-Number' + 1), the endpoint should:
V1) Process the TLV's contained within the Chunk performing the
appropriate actions as indicated by each TLV type. The TLV's MUST
be processed in order within the Chunk. In other words if the sender
puts 3 TLV's in one chunk the first TLV (the one closest to the
Chunk Header) in the Chunk MUST be processed first. The next TLV in
Stewart et.al. [Page 13]
Internet Draft Address/Stream Configuration May 2001
the chunk (the middle one) would be processed second and finally the
last TLV in the Chunk would be processed last.
V2) In processing the chunk, the receiver should build a response
message with the appropriate error TLV's, as specified in the
Parameter type bits for any ASCONF Parameter it does not understand.
To indicate an unrecognized parameter, parameter type 8 as defined
in in the INIT-ACK in 3.3.3 of [RFC2960] should be used. It may also
use the response to carry rejections for other reasons such as
resource shortages etc using the Error Cause TLV and an appropriate
error condition.
Note: a positive response is implied if no error is indicated by the
sender.
V3) All error responses must copy the ASCONF-Request Correlation ID
field received in the ASCONF, from the TLV being responded to, into
the ASCONF-Request Correlation ID field. The ASCONF-Request
Correlation ID always precedes the request TLV.
V4) After processing the entire Chunk, it MUST send all TLV's for
both unrecognized parameters and any other status TLV's inside the
ASCONF-ACK chunk that acknowledges the arrival and processing of the
ASCONF Chunk.
V5) Update the 'Peer-Serial-Number' to the value found in the serial
number field.
C3) If the value found in the serial number is equal to the value
stored in the 'Peer-Serial-Number', the endpoint should:
X1) Parse the ASCONF Chunk TLV's but the endpoint MUST not take any
action on the TLV's parsed (since it has already performed these
actions).
X2) Build a response message with the appropriate response TLV's
as specified in the ASCONF Parameter type bits, for any
parameter it does not understand or could not process.
X3) After parsing the entire Chunk, it MUST send any response
TLV errors and status with a ASCONF-ACK chunk acknowledging the
arrival and processing of the ASCONF Chunk.
X4) The endpoint MUST NOT update its 'Peer-Serial-Number'.
IMPLEMENTATION NOTE: As an optimization a receiver may wish to save
the last ASCONF-ACK for some predetermined period of time and
instead of re-processing the ASCONF (with the same serial number) it
may just re-transmit the ASCONF-ACK. It may wish to use the arrival
of a new serial number to discard the previously saved ASCONF-ACK or
any other means it may choose to expire the saved ASCONF-ACK.
C4) Otherwise, the ASCONF chunk is discarded since it must be either
a stale packet or from an attacker. A receiver of such a packet MAY
Stewart et.al. [Page 14]
Internet Draft Address/Stream Configuration May 2001
log the event for security purposes.
C5) In both cases C2 and C3 the ASCONF-ACK MUST be sent back to the
source address contained in the IP header of the ASCONF being
responded to.
4.3 General rules for address manipulation
When building TLV parameters for the ASCONF Chunk that
will add or delete IP addresses the following rules should be
applied:
D1) When adding an IP address to an association, the IP address is
NOT considered fully added to the association until the ASCONF-ACK
arrives. This means that until such time as the ASCONF containing
the add is acknowledged the sender MUST NOT use the new IP address
as a source for ANY SCTP packet. The receiver of the add IP address
request may use the address has a destination immediately.
D2) After the ASCONF-ACK of an IP address add arrives, the endpoint
MAY begin using the added IP address as a source address.
D3) If an endpoint receives an Error Cause TLV indicating that the
IP address Add, IP address Deletion, or Set Primary IP Address
parameters was not understood, the endpoint MUST consider the
operation failed and MUST NOT attempt to send any subsequent Add,
Delete or Set Primary requests to the peer.
D4) When deleting an IP address from an association, the IP address
MUST be considered a valid destination address for the reception of
SCTP packets until the ASCONF-ACK arrives and MUST NOT be used has a
source address for any subsequent packets. This means that any
datagrams that arrive before the ASCONF-ACK destined to the IP address
being deleted MUST be considered part of the current
association. One special consideration is that ABORT chunks arriving
destined to the IP address being deleted MUST be ignored (see
Section 4.3.1 for further details).
D5) An endpoint MUST NOT delete its last remaining IP address from an
association. In other words if an endpoint is NOT multi-homed it
MUST NOT use the delete IP address. Or if an endpoint sends multiple
requests to delete IP addresses it MUST NOT delete all of the IP
addresses that the peer has listed for the requester.
D6) An endpoint MUST NOT set a source address for an SCTP packet
holding the ASCONF chunk to be the same as an address being deleted
by the ASCONF chunk.
D7) If a request is received to delete the last remaining IP address
of a peer endpoint, the receiver MUST send an Error Cause TLV with
the error cause set to the new error code 'Request to delete last IP
remaingin address'. The requested delete MUST NOT be performed or
acted upon, other than to send the ASCONF-ACK.
Stewart et.al. [Page 15]
Internet Draft Address/Stream Configuration May 2001
D8) If a request is received to delete an IP address which is also
the source address of the IP packet which contained the ASCONF
chunk, the receiver MUST reject this request. To reject the request
the receiver MUST send an Error Cause TLV set to the new error code
"Request to Delete Source IP Address" (unless Rule D5 has also been
violated, in which case the error code 'Request to delete last
remaining IP address' is sent).
D9) If an endpoint receives an ADD IP address request and does not
have the local resources to add this new address to the association,
it MUST return an Error Cause TLV set to the new error code
"Operation Refused due to Resource Shortage".
D10) If an endpoint receives an 'Out of Resource' error in response
to its request to ADD an IP address to an association, it must
either ABORT the association or not consider the address part of the
association. In other words if the endpoint does not ABORT the
association, it must consider the add attempt failed and NOT use
this address and treat SCTP packets destined to the address as Out
Of The Blue packets.
D11) When an endpoint receiving a ASCONF to add an IP address sends
an 'Out of Resource' in its response, it MUST also fail any
subsequent add or delete requests bundled in the ASCONF. The
receiver MUST NOT reject an ADD and then accept a subsequent DELETE
of an IP address in the same ASCONF chunk. In other words, once a
receiver begins failing any ADD or DELETE request, it must fail all
subsequent ADD or DELETE requests contained in that single ASCONF.
D12) When an endpoint receives a request to delete an IP address
that is the current primary address, it is an implementation
decision as to how that endpoint chooses the new primary address.
D13) When an endpoint receives a valid request to DELETE an IP
address the endpoint MUST consider the address no longer as part of
the association. It MUST NOT send SCTP packets for the association
to that address and it MUST treat subsequent packets received from
that address as Out Of The Blue.
During the time interval between sending out the ASCONF and
receiving the ASCONF-ACK it MAY be possible to receive DATA chunks
out of order. The following examples illustrate these problems:
Endpoint-A Endpoint-Z
---------- ----------
ASCONF[Add-IP:X]------------------------------>
/--ASCONF-ACK
/
/--------/---New DATA:
/ / Destination
<-------------------/ / IP:X
/
<--------------------------/
Stewart et.al. [Page 16]
Internet Draft Address/Stream Configuration May 2001
In the above example we see a new IP address (X) being added to
the Endpoint-A. However due to packet re-ordering in the network
a new DATA chunk is sent and arrives at Endpoint-A before
the ASCONF-ACK confirming the add of the address to the association.
A similar problem exists with the deletion of an IP address as
follows:
Endpoint-A Endpoint-Z
---------- ----------
/------------New DATA:
/ Destination
/ IP:X
ASCONF [DEL-IP:X]---------/---------------->
<-----------------/------------------ASCONF-ACK
/
/
<-------------/
In this example we see a DATA chunk destined to the IP:X (which is
about to be deleted) arriving after the deletion is complete.
For the ADD case an endpoint SHOULD consider the newly adding IP
address valid for the association to receive data from during the
interval when awaiting the ASCONF-ACK. The endpoint MUST NOT source
data from this new address until the ASCONF-ACK arrives but it may
receive out of order data as illustrated and MUST NOT treat this
data as an OOTB datagram (please see [RFC2960] section 8.4). It MAY
drop the data silently or it MAY consider it part of the association
but it MUST NOT respond with an ABORT.
For the DELETE case, an endpoint MAY respond to the late arriving DATA
packet as an OOTB datagram or it MAY hold the deleting IP address for a
small period of time as still valid. If it treats the DATA packet as
an OOTB the peer will silently discard the ABORT (since by the time
the ABORT is sent the peer will have removed the IP address from this
association). If the endpoint elects to hold the IP address valid for
a period of time, it MUST NOT hold it valid longer than 2 RTO
intervals for the destination being removed.
4.3.1 A special case for OOTB ABORT chunks
Another case worth mentioning is illustrated below:
Endpoint-A Endpoint-Z
---------- ----------
New DATA:------------\
Source IP:X \
\
ASCONF-REQ[DEL-IP:X]----\------------------>
\ /---------ASCONF-ACK
\ /
\----/-----------> OOTB
Stewart et.al. [Page 17]
Internet Draft Address/Stream Configuration May 2001
(Ignored <---------------------/-------------ABORT
by rule D4) /
<---------------------/
For this case, during the deletion of an IP address, an
Abort MUST be ignored if the destination address of the
Abort message is that of the destination being deleted.
4.4 Setting of the primary address
A sender of this option may elect to send this combined with
a deletion or addition of an address. A sender SHOULD only send
a set primary request to an address that is already considered
part of the association. In other words if a sender combines
a set primary with an add of a new IP address the set primary
will be discarded unless the add request is to be processed
BEFORE the set primary (i.e. it preceeds the set primary).
A request to set primary MAY also appear in a INIT or INIT-ACK
chunk. This can give a hint to the peer endpoint as to which
of its addresses the sender of the INIT or INIT-ACK would like
to be used as the primary address.
The request to set an address as the primary path is an option the
receiver MAY perform. It is considered a hint to the receiver of the
best destination address to use in sending SCTP packets (in the
requester's view). It is possible that the receiver may have other
knowledge that it may act upon and NOT set the specified address as
primary. If a request arrives that asks the receiver to set an
address as primary that does not exist, the receiver should NOT
honor the request, leaving its existing primary address unchanged.
4.5 Steam Flow Limit Procedures
A stream in SCTP is an uni-directional logical channel established
from one to another associated SCTP endpoint, within which all user
messages are delivered in sequence except for those submitted to the
un-ordered delivery service which may arrive out of sequence. Since
each stream is uni-directional and no feedback mechanism exists to
limit a sender, it is possible for one unique stream to monopolize
all of the transport level receiver window space. The mechanism
defined here attempts to alleviate this problem by allowing the
receiver side to communicate to the sender a limit on how much
outstanding data may be sent within a particular stream.
The procedures defined here are broken down into two sides:
o The stream receiver side or peer requesting the limit. And,
o the stream sender side or peer that MUST honor the limit request.
The receivers side is mainly involved with sending the request to
the peer. The senders side is where the actual limitations and flow
limit will occur. Note in section 4.5.1 the stream receiver is the
Stewart et.al. [Page 18]
Internet Draft Address/Stream Configuration May 2001
endpoint that sends the ASCONF message, in section 4.5.2 the sender
side is the endpoint that receives the ASCONF message.
4.5.1 Stream Receiver side procedures
The receiver side SCTP makes decisions on stream flow limit based on
upper layer input. Normally the upper layer makes a request to limit
all or a subset of the active streams that send data to it via an
API interface. How this decision is made is outside the scope of
this document.
Anytime flow limits are made known to the SCTP endpoint by the
application, the receiver side SHOULD create a ASCONF Chunk and
attach to it one or more stream flow limits with there respective
stream number. If the receiver wishes to remove all limits
(previously placed on a particular stream) it may do so by placing
the special value '0' in the 'Flow Limit' field. Once acknowledged
by the peer endpoint the receiver should consider the limit in
place.
Note that the parameter type field upper two bits dictates that any
parameter not understood should be skipped and reported to the
sender with an Operational Error. If an Operational Error is
received that indicates that the 'Stream Flow Limit Request' is not
understood, the sender of the limit request MUST not send subsequent
limit requests. The endpoint SHOULD also inform the upper level
application that the peer endpoint does not support this feature.
4.5.2 Stream Sender side procedures
When a 'Stream Flow Limit Request' is received the sender MUST
record each flow limit with its appropriate stream.
After a limit is set on a stream the sender MUST obey the following
rules when sending to the peer on that stream:
S1) When the upper layer application attempts to send to the peer on
a stream, check the number of outstanding bytes sent to that stream
(those TSN's in queue to be sent, which the cumulative TSN
Acknowledgment has not passed, on this stream) versus the limit set
for that stream (The last received limit for this stream is
henceforth termed the current limit).
S2) If the number of outstanding bytes is greater than or equal to
the current limit, the SCTP endpoint MUST reject the request and NOT
queue the data for transmit. Instead it SHOULD return an error to
the sending application.
S3) If the number of outstanding bytes is less than the current
limit, validate that the data to be sent plus the number of
outstanding bytes is smaller than or equal to this limit. If the
user data plus the number of outstanding bytes is smaller than or
equal to the current limit accept the data for transmit and queue
the user data (increasing the number of outstanding data bytes on
Stewart et.al. [Page 19]
Internet Draft Address/Stream Configuration May 2001
this stream). If the user data plus the number of outstanding bytes
is larger than the current limit for this stream, the SCTP endpoint
MUST reject the request and NOT queue the data for transmit and
instead SHOULD return an error to the application.
S4) Any time a stream limit is updated to the value of 0, consider
this indication to mean no limit is in effect for this stream.
4.5.3 ULP considerations on the use of SCTP flow limit facility
The effect of rule S3 in section 4.5.2 places a maximum size upon a
sender. Once a limit is in effect, if the sending Upper Layer
Protocol (ULP) wishes to send a message that is larger than that
permitted by the imposed stream limit, the ULP will need to provide
a mechanism for fragmentation and re-assembly.
This ULP mechanism is in addition to any fragmentation and
re-assembly that may be provided by SCTP. It is the sole
responsibility of the ULP to handle the case of a single
user message being larger than the stream flow limit, if
applicable.
5. Security Considerations
The ADD/DELETE of an IP address to an existing association does
provide an additional mechanism by which existing associations can
be hijacked. Where the attacker is able to intercept and or alter
the packets sent and received in an association the use of this
feature MAY increase the ease at which an association may be
overtaken. This threat SHOULD be considered when deploying a version
of SCTP that use this feature. The IP Authentication Header
[RFC2402] SHOULD be used when the threat environment requires
stronger integrity protections, but does not require
confidentiality. It should be noted that in the base SCTP
specification [RFC2960], if an attacker is able to intercept and or
alter packets, even without this feature it is possible to hijack an
existing association, please refer to Section 11 of RFC2960.
6. IANA considerations
This document defines the following new SCTP parameters, chunks
and errors:
- Two new Chunk Types,
- Six Parameter Types, and
- Three new SCTP Error Causes.
7. Acknowledgements
The authors wish to thank Jon Berger, John Loughney, Ivan Rodriguez,
Marshall Rose, and Chip Sharp for their invaluable comments.
8. Authors' Addresses
Stewart et.al. [Page 20]
Internet Draft Address/Stream Configuration May 2001
Randall R. Stewart Tel: +1-815-477-2127
Cisco Systems, Inc. EMail: rrs@cisco.com
8745 W. Higgins Road, Suite 200
Chicago, Ill 60631
USA
Micheal A. Ramalho Tel: +1-732-809-0188
Cisco Systems, Inc. EMail: mramalho@cisco.com
1802 Rue de la Porte
Wall Township, NJ 0719-3784
Qiaobing Xie Tel: +1-847-632-3028
Motorola, Inc. EMail: qxie1@email.mot.com
1501 W. Shure Drive, #2309
Arlington Heights, IL 60004
USA
Michael Tuexen Tel: +49-89-722-47210
SIEMENS AG EMail: Michael.Tuexen@icn.siemens.de
Hofmannstr. 51
81359 Munich
Germany
Ian Rytina Tel: +61-3-9301-6164
Ericsson Australia EMail:ian.rytina@ericsson.com
37/360 Elizabeth Street
Melbourne, Victoria 3000
Australia
Phil Conrad Tel: +1-XXX-XXX-XXXX
Netlab Research Group Email conrad@joda.cis.temple.edu
Dept. Of Computer &
Information Sciences
Temple University
1805 N Broad St.
Philadelphia, PA 19122
USA
9. References
[RFC2960] R. R. Stewart, Q. Xie, K. Morneault, C. Sharp,
H. J. Schwarzbauer, T. Taylor, I. Rytina, M. Kalla, L. Zhang,
and, V. Paxson, "Stream Control Transmission Protocol," RFC
2960, October 2000.
[RFC2026] Bradner, S., "The Internet Standards Process -- Revision
3", RFC 2026, October 1996.
[RFC2119] Bradner, S. "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2402] S. Kent, R. Atkinson., "IP Authentication Header.", RFC
2402, November 1998.
Stewart et.al. [Page 21]
Internet Draft Address/Stream Configuration May 2001
This Internet Draft expires in 6 months from May, 2001
Stewart et.al. [Page 22]