Transport Area Working Group B. Briscoe Internet-Draft BT Updates: 3168, 4301 December 20, 2009 (if approved) Intended status: Standards Track Expires: June 23, 2010 Tunnelling of Explicit Congestion Notification draft-ietf-tsvwg-ecn-tunnel-06 Abstract This document redefines how the explicit congestion notification (ECN) field of the IP header should be constructed on entry to and exit from any IP in IP tunnel. On encapsulation it updates RFC3168 to bring all IP in IP tunnels (v4 or v6) into line with RFC4301 IPsec ECN processing. On decapsulation it updates both RFC3168 and RFC4301 to add new behaviours for previously unused combinations of inner and outer header. The new rules ensure the ECN field is correctly propagated across a tunnel whether it is used to signal one or two severity levels of congestion, whereas before only one severity level was supported. Tunnel endpoints can be updated in any order without affecting pre-existing uses of the ECN field (backward compatible). Nonetheless, operators wanting to support two severity levels (e.g. for pre-congestion notification--PCN) can require compliance with this new specification. A thorough analysis of the reasoning for these changes and the implications is included. In the unlikely event that the new rules do not meet a specific need, RFC4774 gives guidance on designing alternate ECN semantics and this document extends that to include tunnelling issues. Status of This Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at Briscoe Expires June 23, 2010 [Page 1]
Internet-Draft ECN Tunnelling December 2009 http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on June 23, 2010. Copyright Notice Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License. Briscoe Expires June 23, 2010 [Page 2]
Internet-Draft ECN Tunnelling December 2009 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 11 3. Summary of Pre-Existing RFCs . . . . . . . . . . . . . . . . . 12 3.1. Encapsulation at Tunnel Ingress . . . . . . . . . . . . . 12 3.2. Decapsulation at Tunnel Egress . . . . . . . . . . . . . . 13 4. New ECN Tunnelling Rules . . . . . . . . . . . . . . . . . . . 14 4.1. Default Tunnel Ingress Behaviour . . . . . . . . . . . . . 14 4.2. Default Tunnel Egress Behaviour . . . . . . . . . . . . . 15 4.3. Encapsulation Modes . . . . . . . . . . . . . . . . . . . 17 4.4. Single Mode of Decapsulation . . . . . . . . . . . . . . . 18 5. Updates to Earlier RFCs . . . . . . . . . . . . . . . . . . . 19 5.1. Changes to RFC4301 ECN processing . . . . . . . . . . . . 19 5.2. Changes to RFC3168 ECN processing . . . . . . . . . . . . 20 5.3. Motivation for Changes . . . . . . . . . . . . . . . . . . 20 5.3.1. Motivation for Changing Encapsulation . . . . . . . . 21 5.3.2. Motivation for Changing Decapsulation . . . . . . . . 22 6. Backward Compatibility . . . . . . . . . . . . . . . . . . . . 24 6.1. Non-Issues Updating Decapsulation . . . . . . . . . . . . 24 6.2. Non-Update of RFC4301 IPsec Encapsulation . . . . . . . . 25 6.3. Update to RFC3168 Encapsulation . . . . . . . . . . . . . 25 7. Design Principles for Alternate ECN Tunnelling Semantics . . . 26 8. Security Considerations . . . . . . . . . . . . . . . . . . . 28 9. Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . 29 10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 30 11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 30 11.1. Normative References . . . . . . . . . . . . . . . . . . . 30 11.2. Informative References . . . . . . . . . . . . . . . . . . 31 Appendix A. Early ECN Tunnelling RFCs . . . . . . . . . . . . . . 33 Appendix B. Design Constraints . . . . . . . . . . . . . . . . . 33 B.1. Security Constraints . . . . . . . . . . . . . . . . . . . 33 B.2. Control Constraints . . . . . . . . . . . . . . . . . . . 35 B.3. Management Constraints . . . . . . . . . . . . . . . . . . 36 Appendix C. Contribution to Congestion across a Tunnel . . . . . 37 Appendix D. Why Losing ECT(1) on Decapsulation Impedes PCN . . . 38 Appendix E. Why Resetting ECN on Encapsulation Impedes PCN . . . 39 Appendix F. Compromise on Decap with ECT(1) Inner and ECT(0) Outer . . . . . . . . . . . . . . . . . . . . . . . . 40 Appendix G. Open Issues . . . . . . . . . . . . . . . . . . . . . 41 Briscoe Expires June 23, 2010 [Page 3]
Internet-Draft ECN Tunnelling December 2009 Request to the RFC Editor (to be removed on publication): In the RFC index, RFC3168 should be identified as an update to RFC2003. RFC4301 should be identified as an update to RFC3168. Changes from previous drafts (to be removed by the RFC Editor) Full text differences between IETF draft versions are available at <http://tools.ietf.org/wg/tsvwg/draft-ietf-tsvwg-ecn-tunnel/>, and between earlier individual draft versions at <http://www.briscoe.net/pubs.html#ecn-tunnel> From ietf-05 to ietf-06 (current): * Minor textual clarifications and corrections. From ietf-04 to ietf-05: * Functional changes: + Section 4.2: ECT(1) outer with Not-ECT inner: reverted to forwarding as Not-ECT (as in RFC3168 & RFC4301), rather than dropping. + Altered rationale in bullet 3 of Section 5.3.2 to justify this. + Distinguished alarms for dangerous and invalid combinations and allowed combinations that are valid in some tunnel configurations but dangerous in others to be alarmed at the discretion of the implementer and/or operator. + Altered advice on designing alternate ECN tunnelling semantics to reflect the above changes. * Textual changes: + Changed "Future non-default schemes" to "Alternate ECN Tunnelling Semantics" throughout. + Cut down Appendix D and Appendix E for brevity. + A number of clarifying edits & updated refs. Briscoe Expires June 23, 2010 [Page 4]
Internet-Draft ECN Tunnelling December 2009 From ietf-03 to ietf-04: * Functional changes: none * Structural changes: + Added "Open Issues" appendix * Textual changes: + Section title: "Changes from Earlier RFCs" -> "Updates to Earlier RFCs" + Emphasised that change on decap to previously unused combinations will propagate PCN encoding. + Acknowledged additional reviewers and updated references From ietf-02 to ietf-03: * Functional changes: + Corrected errors in recap of previous RFCs, which wrongly stated the different decapsulation behaviours of RFC3168 & RFC4301 with a Not-ECT inner header. This also required corrections to the "Changes from Earlier RFCs" and the Motivations for these changes. + Mandated that any future standards action SHOULD NOT use the ECT(0) codepoint as an indication of congestion, without giving strong reasons. + Added optional alarm when decapsulating ECT(1) outer, ECT(0), but noted it would need to be disabled for 2-severity level congestion (e.g. PCN). * Structural changes: + Removed Document Roadmap which merely repeated the Contents (previously Section 1.2). + Moved "Changes from Earlier RFCs" (Section 5) before Section 6 on Backward Compatibility and internally organised both by RFC, rather than by ingress then egress. + Moved motivation for changing existing RFCs (Section 5.3) to after the changes are specified. Briscoe Expires June 23, 2010 [Page 5]
Internet-Draft ECN Tunnelling December 2009 + Moved informative "Design Principles for Future Non-Default Schemes" after all the normative sections. + Added Appendix A on early history of ECN tunnelling RFCs. + Removed specialist appendix on "Relative Placement of Tunnelling and In-Path Load Regulation" (Appendix D in the -02 draft) + Moved and updated specialist text on "Compromise on Decap with ECT(1) Inner and ECT(0) Outer" from Security Considerations to Appendix F * Textual changes: + Simplified vocabulary for non-native-english speakers + Simplified Introduction and defined regularly used terms in an expanded Terminology section. + More clearly distinguished statically configured tunnels from dynamic tunnel endpoint discovery, before explaining operating modes. + Simplified, cut-down and clarified throughout + Updated references. From ietf-01 to ietf-02: * Scope reduced from any encapsulation of an IP packet to solely IP in IP tunnelled encapsulation. Consequently changed title and removed whole section 'Design Guidelines for New Encapsulations of Congestion Notification' (to be included in a future companion informational document). * Included a new normative decapsulation rule for ECT(0) inner and ECT(1) outer that had previously only been outlined in the non-normative appendix 'Comprehensive Decapsulation Rules'. Consequently: + The Introduction has been completely re-written to motivate this change to decapsulation along with the existing change to encapsulation. + The tentative text in the appendix that first proposed this change has been split between normative standards text in Section 4 and Appendix D, which explains specifically why Briscoe Expires June 23, 2010 [Page 6]
Internet-Draft ECN Tunnelling December 2009 this change would streamline PCN. New text on the logic of the resulting decap rules added. * If inner/outer is Not-ECT/ECT(0), changed decapsulation to propagate Not-ECT rather than drop the packet; and added reasoning. * Considerably restructured: + "Design Constraints" analysis moved to an appendix (Appendix B); + Added Section 3 to summarise relevant existing RFCs; + Structured Section 4 and Section 6 into subsections. + Added tables to sections on old and new rules, for precision and comparison. + Moved Section 7 on Design Principles to the end of the section specifying the new default normative tunnelling behaviour. Rewritten and shifted text on identifiers and in-path load regulators to Appendix B.1 [deleted in revision -03]. From ietf-00 to ietf-01: * Identified two additional alarm states in the decapsulation rules (Figure 4) if ECT(X) in outer and inner contradict each other. * Altered Comprehensive Decapsulation Rules (Appendix D) so that ECT(0) in the outer no longer overrides ECT(1) in the inner. Used the term 'Comprehensive' instead of 'Ideal'. And considerably updated the text in this appendix. * Added Appendix D.1 (removed again in a later revision) to weigh up the various ways the Comprehensive Decapsulation Rules might be introduced. This replaces the previous contradictory statements saying complex backwards compatibility interactions would be introduced while also saying there would be no backwards compatibility issues. * Updated references. Briscoe Expires June 23, 2010 [Page 7]
Internet-Draft ECN Tunnelling December 2009 From briscoe-01 to ietf-00: * Re-wrote Appendix C giving much simpler technique to measure contribution to congestion across a tunnel. * Added discussion of backward compatibility of the ideal decapsulation scheme in Appendix D * Updated references. Minor corrections & clarifications throughout. From briscoe-00 to briscoe-01: * Related everything conceptually to the uniform and pipe models of RFC2983 on Diffserv Tunnels, and completely removed the dependence of tunnelling behaviour on the presence of any in- path load regulation by using the [1 - Before] [2 - Outer] function placement concepts from RFC2983; * Added specific cases where the existing standards limit new proposals, particularly Appendix E; * Added sub-structure to Introduction (Need for Rationalisation, Roadmap), added new Introductory subsection on "Scope" and improved clarity; * Added Design Guidelines for New Encapsulations of Congestion Notification; * Considerably clarified the Backward Compatibility section (Section 6); * Considerably extended the Security Considerations section (Section 8); * Summarised the primary rationale much better in the conclusions; * Added numerous extra acknowledgements; * Added Appendix E. "Why resetting CE on encapsulation harms PCN", Appendix C. "Contribution to Congestion across a Tunnel" and Appendix D. "Ideal Decapsulation Rules"; * Re-wrote Appendix B [deleted in a later revision], explaining how tunnel encapsulation no longer depends on in-path load- regulation (changed title from "In-path Load Regulation" to "Non-Dependence of Tunnelling on In-path Load Regulation"), but Briscoe Expires June 23, 2010 [Page 8]
Internet-Draft ECN Tunnelling December 2009 explained how an in-path load regulation function must be carefully placed with respect to tunnel encapsulation (in a new sub-section entitled "Dependence of In-Path Load Regulation on Tunnelling"). 1. Introduction Explicit congestion notification (ECN [RFC3168]) allows a forwarding element to notify the onset of congestion without having to drop packets. Instead it can explicitly mark a proportion of packets in the 2-bit ECN field in the IP header (Table 1 recaps the ECN codepoints). The outer header of an IP packet can encapsulate one or more IP headers for tunnelling. A forwarding element using ECN to signify congestion will only mark the immediately visible outer IP header. When a tunnel decapsulator later removes this outer header, it follows rules to propagate congestion markings by combining the ECN fields of the inner and outer IP header into one outgoing IP header. This document updates those rules for IPsec [RFC4301] and non-IPsec [RFC3168] tunnels to add new behaviours for previously unused combinations of inner and outer header. It also updates the tunnel ingress behaviour of RFC3168 to match that of RFC4301. The updated rules are backward compatible with RFC4301 and RFC3168 when interworking with any other tunnel endpoint complying with any earlier specification. When ECN and its tunnelling was defined in RFC3168, only the minimum necessary changes to the ECN field were propagated through tunnel endpoints--just enough for the basic ECN mechanism to work. This was due to concerns that the ECN field might be toggled to communicate between a secure site and someone on the public Internet--a covert channel. This was because a mutable field like ECN cannot be protected by IPsec's integrity mechanisms--it has to be able to change as it traverses the Internet. Nonetheless, the latest IPsec architecture [RFC4301] considered a bandwidth limit of 2 bits per packet on a covert channel made it a manageable risk. Therefore, for simplicity, an RFC4301 ingress copied the whole ECN field to encapsulate a packet. It also dispensed with the two modes of RFC3168, one which partially copied the ECN field, and the other which blocked all propagation of ECN changes. Unfortunately, this entirely reasonable sequence of standards actions resulted in a perverse outcome; non-IPsec tunnels (RFC3168) blocked the 2-bit covert channel, while IPsec tunnels (RFC4301) did not--at Briscoe Expires June 23, 2010 [Page 9]
Internet-Draft ECN Tunnelling December 2009 least not at the ingress. At the egress, both IPsec and non-IPsec tunnels still partially restricted propagation of the full ECN field. The trigger for the changes in this document was the introduction of pre-congestion notification (PCN [RFC5670]) to the IETF standards track. PCN needs the ECN field to be copied at a tunnel ingress and it needs four states of congestion signalling to be propagated at the egress, but pre-existing tunnels only propagate three in the ECN field. This document draws on currently unused (CU) combinations of inner and outer headers to add tunnelling of four-state congestion signalling to RFC3168 and RFC4301. Operators of tunnels who specifically want to support four states can require that all their tunnels comply with this specification. Nonetheless, all tunnel endpoint implementations (RFC4301, RFC3168, RFC2481, RFC2401, RFC2003) can safely be updated to this new specification as part of general code maintenance. This will gradually add support for four congestion states to the Internet. Existing three state schemes will continue to work as before. At the same time as harmonising covert channel constraints, the opportunity has been taken to draw together diverging tunnel specifications into a single consistent behaviour. Then any tunnel can be deployed unilaterally, and it will support the full range of congestion control and management schemes without any modes or configuration. Further, any host or router can expect the ECN field to behave in the same way, whatever type of tunnel might intervene in the path. 1.1. Scope This document only concerns wire protocol processing of the ECN field at tunnel endpoints and makes no changes or recommendations concerning algorithms for congestion marking or congestion response. This document specifies common ECN field processing at encapsulation and decapsulation for any IP in IP tunnelling, whether IPsec or non- IPsec tunnels. It applies irrespective of whether IPv4 or IPv6 is used for either of the inner and outer headers. It applies for packets with any destination address type, whether unicast or multicast. It applies as the default for all Diffserv per-hop behaviours (PHBs), unless stated otherwise in the specification of a PHB. It is intended to be a good trade off between somewhat conflicting security, control and management requirements. [RFC2983] is a comprehensive primer on differentiated services and tunnels. Given ECN raises similar issues to differentiated services Briscoe Expires June 23, 2010 [Page 10]
Internet-Draft ECN Tunnelling December 2009 when interacting with tunnels, useful concepts introduced in RFC2983 are used throughout, with brief recaps of the explanations where necessary. 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Table 1 recaps the names of the ECN codepoints [RFC3168]. +------------------+----------------+---------------------------+ | Binary codepoint | Codepoint name | Meaning | +------------------+----------------+---------------------------+ | 00 | Not-ECT | Not ECN-capable transport | | 01 | ECT(1) | ECN-capable transport | | 10 | ECT(0) | ECN-capable transport | | 11 | CE | Congestion experienced | +------------------+----------------+---------------------------+ Table 1: Recap of Codepoints of the ECN Field [RFC3168] in the IP Header Further terminology used within this document: Encapsulator: The tunnel endpoint function that adds an outer IP header to tunnel a packet (also termed the 'ingress tunnel endpoint' or just the 'ingress' where the context is clear). Decapsulator: The tunnel endpoint function that removes an outer IP header from a tunnelled packet (also termed the 'egress tunnel endpoint' or just the 'egress' where the context is clear). Incoming header: The header of an arriving packet before encapsulation. Outer header: The header added to encapsulate a tunnelled packet. Inner header: The header encapsulated by the outer header. Outgoing header: The header constructed by the decapsulator using logic that combines the fields in the outer and inner headers. Copying ECN: On encapsulation, setting the ECN field of the new outer header to be a copy of the ECN field in the incoming header. Briscoe Expires June 23, 2010 [Page 11]
Internet-Draft ECN Tunnelling December 2009 Zeroing ECN: On encapsulation, clearing the ECN field of the new outer header to Not-ECT ("00"). Resetting ECN: On encapsulation, setting the ECN field of the new outer header to be a copy of the ECN field in the incoming header except the outer ECN field is set to the ECT(0) codepoint if the incoming ECN field is CE ("11"). 3. Summary of Pre-Existing RFCs This section is informative not normative, as it recaps pre-existing RFCs. Earlier relevant RFCs that were either experimental or incomplete with respect to ECN tunnelling (RFC2481, RFC2401 and RFC2003) are briefly outlined in Appendix A. The question of whether tunnel implementations used in the Internet comply with any of these RFCs is not discussed. 3.1. Encapsulation at Tunnel Ingress At the encapsulator, the controversy has been over whether to propagate information about congestion experienced on the path so far into the outer header of the tunnel. Specifically, RFC3168 says that, if a tunnel fully supports ECN (termed a 'full-functionality' ECN tunnel in [RFC3168]), the encapsulator must not copy a CE marking from the inner header into the outer header that it creates. Instead the encapsulator must set the outer header to ECT(0) if the ECN field is marked CE in the arriving IP header. We term this 'resetting' a CE codepoint. However, the new IPsec architecture in [RFC4301] reverses this rule, stating that the encapsulator must simply copy the ECN field from the incoming header to the outer header. RFC3168 also provided a Limited Functionality mode that turns off ECN processing over the scope of the tunnel by setting the outer header to Not-ECT ("00"). Then such packets will be dropped to indicate congestion rather than marked with ECN. This is necessary for the ingress to interwork with legacy decapsulators ([RFC2481], [RFC2401] and [RFC2003]) that do not propagate ECN markings added to the outer header. Otherwise such legacy decapsulators would throw away congestion notifications before they reached the transport layer. Neither Limited Functionality mode nor Full Functionality mode are used by an RFC4301 IPsec encapsulator, which simply copies the incoming ECN field into the outer header. An earlier key-exchange phase ensures an RFC4301 ingress will not have to interwork with a legacy egress that does not support ECN. Briscoe Expires June 23, 2010 [Page 12]
Internet-Draft ECN Tunnelling December 2009 These pre-existing behaviours are summarised in Figure 1. +-----------------+-----------------------------------------------+ | Incoming Header | Outgoing Outer Header | | (also equal to +---------------+---------------+---------------+ | Outgoing Inner | RFC3168 ECN | RFC3168 ECN | RFC4301 IPsec | | Header) | Limited | Full | | | | Functionality | Functionality | | +-----------------+---------------+---------------+---------------+ | Not-ECT | Not-ECT | Not-ECT | Not-ECT | | ECT(0) | Not-ECT | ECT(0) | ECT(0) | | ECT(1) | Not-ECT | ECT(1) | ECT(1) | | CE | Not-ECT | ECT(0) | CE | +-----------------+---------------+---------------+---------------+ Figure 1: IP in IP Encapsulation: Recap of Pre-existing Behaviours 3.2. Decapsulation at Tunnel Egress RFC3168 and RFC4301 specify the decapsulation behaviour summarised in Figure 2. The ECN field in the outgoing header is set to the codepoint at the intersection of the appropriate incoming inner header (row) and incoming outer header (column). +---------+------------------------------------------------+ |Incoming | Incoming Outer Header | | Inner +---------+------------+------------+------------+ | Header | Not-ECT | ECT(0) | ECT(1) | CE | +---------+---------+------------+------------+------------+ RFC3168->| Not-ECT | Not-ECT |Not-ECT |Not-ECT | drop | RFC4301->| Not-ECT | Not-ECT |Not-ECT |Not-ECT |Not-ECT | | ECT(0) | ECT(0) | ECT(0) | ECT(0) | CE | | ECT(1) | ECT(1) | ECT(1) | ECT(1) | CE | | CE | CE | CE | CE | CE | +---------+---------+------------+------------+------------+ | Outgoing Header | +------------------------------------------------+ Figure 2: IP in IP Decapsulation; Recap of Pre-existing Behaviour The behaviour in the table derives from the logic given in RFC3168 and RFC4301, briefly recapped as follows: o On decapsulation, if the inner ECN field is Not-ECT the outer is discarded. RFC3168 (but not RFC4301) also specified that the decapsulator must drop a packet with a Not-ECT inner and CE in the outer. Briscoe Expires June 23, 2010 [Page 13]
Internet-Draft ECN Tunnelling December 2009 o In all other cases, if the outer is CE, the outgoing ECN field is set to CE, but otherwise the outer is ignored and the inner is used for the outgoing ECN field. RFC3168 also made it an auditable event for an IPsec tunnel "if the ECN Field is changed inappropriately within an IPsec tunnel...". Inappropriate changes were not specifically enumerated. RFC4301 did not mention inappropriate ECN changes. 4. New ECN Tunnelling Rules The standards actions below in Section 4.1 (ingress encapsulation) and Section 4.2 (egress decapsulation) define new default ECN tunnel processing rules for any IP packet (v4 or v6) with any Diffserv codepoint. If these defaults do not meet a particular requirement, an alternate ECN tunnelling scheme can be introduced as part of the definition of an alternate congestion marking scheme used by a specific Diffserv PHB (see S.5 of [RFC3168] and [RFC4774]). When designing such alternate ECN tunnelling schemes, the principles in Section 7 should be followed. However, alternate ECN tunnelling schemes are NOT RECOMMENDED as the deployment burden of handling exceptional PHBs in implementations of all affected tunnels should not be underestimated. There is no requirement for a PHB definition to state anything about ECN tunnelling behaviour if the default behaviour in the present specification is sufficient. 4.1. Default Tunnel Ingress Behaviour Two modes of encapsulation are defined here; `normal mode' and `compatibility mode', which is for backward compatibility with tunnel decapsulators that do not understand ECN. Section 4.3 explains why two modes are necessary and specifies the circumstances in which it is sufficient to solely implement normal mode. Note that these are modes of the ingress tunnel endpoint only, not the whole tunnel. Whatever the mode, an encapsulator forwards the inner header without changing the ECN field. In normal mode an encapsulator compliant with this specification MUST construct the outer encapsulating IP header by copying the 2-bit ECN field of the incoming IP header. In compatibility mode it clears the ECN field in the outer header to the Not-ECT codepoint (the IPv4 header checksum also changes whenever the ECN field is changed). These rules are tabulated for convenience in Figure 3. Briscoe Expires June 23, 2010 [Page 14]
Internet-Draft ECN Tunnelling December 2009 +-----------------+-------------------------------+ | Incoming Header | Outgoing Outer Header | | (also equal to +---------------+---------------+ | Outgoing Inner | Compatibility | Normal | | Header) | Mode | Mode | +-----------------+---------------+---------------+ | Not-ECT | Not-ECT | Not-ECT | | ECT(0) | Not-ECT | ECT(0) | | ECT(1) | Not-ECT | ECT(1) | | CE | Not-ECT | CE | +-----------------+---------------+---------------+ Figure 3: New IP in IP Encapsulation Behaviours An ingress in compatibility mode encapsulates packets identically to an ingress in RFC3168's limited functionality mode. An ingress in normal mode encapsulates packets identically to an RFC4301 IPsec ingress. 4.2. Default Tunnel Egress Behaviour To decapsulate the inner header at the tunnel egress, a compliant tunnel egress MUST set the outgoing ECN field to the codepoint at the intersection of the appropriate incoming inner header (row) and outer header (column) in Figure 4 (the IPv4 header checksum also changes whenever the ECN field is changed). There is no need for more than one mode of decapsulation, as these rules cater for all known requirements. +---------+------------------------------------------------+ |Incoming | Incoming Outer Header | | Inner +---------+------------+------------+------------+ | Header | Not-ECT | ECT(0) | ECT(1) | CE | +---------+---------+------------+------------+------------+ | Not-ECT | Not-ECT |Not-ECT(!!!)|Not-ECT(!!!)| drop(!!!)| | ECT(0) | ECT(0) | ECT(0) | ECT(1) | CE | | ECT(1) | ECT(1) | ECT(1) (!) | ECT(1) | CE | | CE | CE | CE | CE(!!!)| CE | +---------+---------+------------+------------+------------+ | Outgoing Header | +------------------------------------------------+ Currently unused combinations are indicated by '(!!!)' or '(!)' Figure 4: New IP in IP Decapsulation Behaviour This table for decapsulation behaviour is derived from the following logic: Briscoe Expires June 23, 2010 [Page 15]
Internet-Draft ECN Tunnelling December 2009 o If the inner ECN field is Not-ECT the decapsulator MUST NOT propagate any other ECN codepoint onwards. This is because the inner Not-ECT marking is set by transports that use drop as an indication of congestion and would not understand or respond to any other ECN codepoint [RFC4774]. In addition: * If the inner ECN field is Not-ECT and the outer ECN field is CE the decapsulator MUST drop the packet. * If the inner ECN field is Not-ECT and the outer ECN field is Not-ECT, ECT(0) or ECT(1) the decapsulator MUST forward the outgoing packet with the ECN field cleared to Not-ECT. o In all other cases where the inner supports ECN, the decapsulator MUST set the outgoing ECN field to the more severe marking of the outer and inner ECN fields, where the ranking of severity from highest to lowest is CE, ECT(1), ECT(0), Not-ECT. This in no way precludes cases where ECT(1) and ECT(0) have the same severity; o Certain combinations of inner and outer ECN fields cannot result from any transition in any current or previous ECN tunneling specification. These currently unused (CU) combinations are indicated in Figure 4 by '(!!!)' or '(!)', where '(!!!)' means the combination is CU and always potentially dangerous, while '(!)' means it is CU and possibly dangerous. In these cases, particularly the more dangerous ones, the decapsulator SHOULD log the event and MAY also raise an alarm. Just because the highlighted combinations are currently unused, does not mean that all the other combinations are always valid. Some are only valid if they have arrived from a particular type of legacy ingress, and dangerous otherwise. Therefore an implementation MAY allow an operator to configure logging and alarms for such additional header combinations known to be dangerous or CU for the particular configuration of tunnel endpoints deployed at run-time. Alarms should be rate-limited so that the anomalous combinations will not amplify into a flood of alarm messages. It MUST be possible to suppress alarms or logging, e.g. if it becomes apparent that a combination that previously was not used has started to be used for legitimate purposes such as a new standards action. The above logic allows for ECT(0) and ECT(1) to both represent the same severity of congestion marking (e.g. "not congestion marked"). But it also allows future schemes to be defined where ECT(1) is a more severe marking than ECT(0), in particular enabling the simplest Briscoe Expires June 23, 2010 [Page 16]
Internet-Draft ECN Tunnelling December 2009 possible encoding for PCN [I-D.ietf-pcn-3-in-1-encoding]. This approach is discussed in Appendix D and in the discussion of the ECN nonce [RFC3540] in Section 8, which in turn refers to Appendix F. 4.3. Encapsulation Modes Section 4.1 introduces two encapsulation modes, normal mode and compatibility mode, defining their encapsulation behaviour (i.e. header copying or zeroing respectively). Note that these are modes of the ingress tunnel endpoint only, not the tunnel as a whole. A tunnel ingress MUST at least implement `normal mode' and, if it might be used with legacy tunnel egress nodes (RFC2003, RFC2401 or RFC2481 or the limited functionality mode of RFC3168), it MUST also implement `compatibility mode' for backward compatibility with tunnel egresses that do not propagate explicit congestion notifications [RFC4774]. If the egress does support propagation of ECN (full functionality mode of RFC3168 or RFC4301 or the present specification), the ingress SHOULD use normal mode, in order to support ECN where possible. We can categorise the way that an ingress tunnel endpoint is paired with an egress as either: static: those paired together by prior configuration or; dynamically discovered: those paired together by some form of tunnel endpoint discovery, typically driven by the path taken by arriving packets. Static: Some implementations of encapsulator might be constrained to be statically deployed, and constrained to never be paired with a legacy decapsulator (RFC2003, RFC2401 or RFC2481 or the limited functionality mode of RFC3168). In such a case, only normal mode needs to be implemented. For instance, RFC4301-compatible IPsec tunnel endpoints invariably use IKEv2 [RFC4306] for key exchange, which was introduced alongside RFC4301. Therefore both endpoints of an RFC4301 tunnel can be sure that the other end is RFC4301-compatible, because the tunnel is only formed after IKEv2 key management has completed, at which point both ends will be RFC4301-compliant by definition. Further, an RFC4301 encapsulator behaves identically to the normal mode of the present specification and does not need to implement compatibility mode as it will never interact with legacy ECN tunnels. Dynamic Discovery: This specification does not require or recommend dynamic discovery and it does not define how dynamic negotiation Briscoe Expires June 23, 2010 [Page 17]
Internet-Draft ECN Tunnelling December 2009 might be done, but it recognises that proprietary tunnel endpoint discovery protocols exist. It therefore sets down some constraints on discovery protocols to ensure safe interworking. If dynamic tunnel endpoint discovery might pair an ingress with a legacy egress (RFC2003, RFC2401 or RFC2481 or the limited functionality mode of RFC3168), the ingress MUST implement both normal and compatibility mode. If the tunnel discovery process is arranged to only ever find a tunnel egress that propagates ECN (RFC3168 full functionality mode, RFC4301 or this present specification), then a tunnel ingress can be complaint with the present specification without implementing compatibility mode. If a compliant tunnel ingress is discovering an egress, it MUST send packets in compatibility mode in case the egress it discovers is a legacy egress. If, through the discovery protocol, the egress indicates that it is compliant with the present specification, with RFC4301 or with RFC3168 full functionality mode, the ingress can switch itself into normal mode. If the egress denies compliance with any of these or returns an error that implies it does not understand a request to work to any of these ECN specifications, the tunnel ingress MUST remain in compatibility mode. An ingress cannot claim compliance with this specification simply by permanently disabling ECN processing across the tunnel (i.e. only implementing compatibility mode). It is true that such a tunnel ingress is at least safe with the ECN behaviour of any egress it may encounter, but it does not meet the aim of introducing ECN support to tunnels. Implementation note: if a compliant node is the ingress for multiple tunnels, a mode setting will need to be stored for each tunnel ingress. However, if a node is the egress for multiple tunnels, none of the tunnels will need to store a mode setting, because a compliant egress can only be in one mode. 4.4. Single Mode of Decapsulation A compliant decapsulator only has one mode of operation. However, if a complaint egress is implemented to be dynamically discoverable, it may need to respond to discovery requests from various types of legacy tunnel ingress. This specification does not define how dynamic negotiation might be done by (proprietary) discovery protocols, but it sets down some constraints to ensure safe interworking. Through the discovery protocol, a tunnel ingress compliant with the present specification might ask if the egress is compliant with the Briscoe Expires June 23, 2010 [Page 18]
Internet-Draft ECN Tunnelling December 2009 present specification, with RFC4301 or with RFC3168 full functionality mode. Or an RFC3168 tunnel ingress might try to negotiate to use limited functionality or full functionality mode [RFC3168]. In all these cases, a decapsulating tunnel egress compliant with this specification MUST agree to any of these requests, since it will behave identically in all these cases. If no ECN-related mode is requested, a compliant tunnel egress MUST continue without raising any error or warning as its egress behaviour is compatible with all the legacy ingress behaviours that do not negotiate capabilities. A compliant tunnel egress SHOULD raise a warning alarm about any requests to enter modes it does not recognise but, for 'forward compatibility' with standards actions possibly defined after it was implemented, it SHOULD continue operating. 5. Updates to Earlier RFCs 5.1. Changes to RFC4301 ECN processing Ingress: An RFC4301 IPsec encapsulator is not changed at all by the present specification Egress: The new decapsulation behaviour in Figure 4 updates RFC4301. However, it solely updates combinations of inner and outer that would never result from any protocol defined in the RFC series so far, even though they were catered for in RFC4301 for completeness. Therefore, the present specification adds new behaviours to RFC4301 decapsulation without altering existing behaviours. The following specific updates have been made: * The outer, not the inner, is propagated when the outer is ECT(1) and the inner is ECT(0); * A packet with Not-ECT in the inner and an outer of CE is dropped rather than forwarded as Not-ECT; * Certain combinations of inner and outer ECN field have been identified as currently unused. These can trigger logging and/or raise alarms. Modes: RFC4301 does not need modes and is not updated by the modes in the present specification. The normal mode of encapsulation is unchanged from RFC4301 encapsulation and an RFC4301 IPsec ingress will never need compatibility mode as explained in Section 4.3 (except in one corner-case described below). One corner case can exist where an RFC4301 ingress does not use Briscoe Expires June 23, 2010 [Page 19]
Internet-Draft ECN Tunnelling December 2009 IKEv2, but uses manual keying instead. Then an RFC4301 ingress could conceivably be configured to tunnel to an egress with limited functionality ECN handling. Strictly, for this corner- case, the requirement to use compatibility mode in this specification updates RFC4301. However, this is such a remote possibility that RFC4301 IPsec implementations are NOT REQUIRED to implement compatibility mode. 5.2. Changes to RFC3168 ECN processing Ingress: On encapsulation, the new rule in Figure 3 that a normal mode tunnel ingress copies any ECN field into the outer header updates the ingress behaviour of RFC3168. Nonetheless, the new compatibility mode is identical to the limited functionality mode of RFC3168. Egress: The new decapsulation behaviour in Figure 4 updates RFC3168. However, the present specification solely updates combinations of inner and outer that would never result from any protocol defined in the RFC series so far, even though they were catered for in RFC3168 for completeness. Therefore, the present specification adds new behaviours to RFC3168 decapsulation without altering existing behaviours. The following specific updates have been made: * The outer, not the inner, is propagated when the outer is ECT(1) and the inner is ECT(0); * Certain combinations of inner and outer ECN field have been identified as currently unused. These can trigger logging and/or raise alarms. Modes: RFC3168 defines a (required) limited functionality mode and an (optional) full functionality mode for a tunnel. In RFC3168, modes applied to both ends of the tunnel, while in the present specification, modes are only used at the ingress--a single egress behaviour covers all cases. The normal mode of encapsulation updates the encapsulation behaviour of the full functionality mode of RFC3168. The compatibility mode of encapsulation is identical to the encapsulation behaviour of the limited functionality mode of RFC3168. The constraints on how tunnel discovery protocols set modes in Section 4.3 and Section 4.4 are an update to RFC3168. 5.3. Motivation for Changes An overriding goal is to ensure the same ECN signals can mean the same thing whatever tunnels happen to encapsulate an IP packet flow. This removes gratuitous inconsistency, which otherwise constrains the Briscoe Expires June 23, 2010 [Page 20]
Internet-Draft ECN Tunnelling December 2009 available design space and makes it harder to design networks and new protocols that work predictably. 5.3.1. Motivation for Changing Encapsulation The normal mode in Section 4 updates RFC3168 to make all IP in IP encapsulation of the ECN field consistent--consistent with the way both RFC4301 IPsec [RFC4301] and IP in MPLS or MPLS in MPLS encapsulation [RFC5129] construct the ECN field. Compatibility mode has also been defined so a non-RFC4301 ingress can still switch to using drop across a tunnel for backwards compatibility with legacy decapsulators that do not propagate ECN correctly. The trigger that motivated this update to RFC3168 encapsulation was a standards track proposal for pre-congestion notification (PCN [RFC5670]). PCN excess rate marking only works correctly if the ECN field is copied on encapsulation (as in RFC4301 and RFC5129); it does not work if ECN is reset (as in RFC3168). This is because PCN excess rate marking depends on the outer header revealing any congestion experienced so far on the whole path, not just since the last tunnel ingress (see Appendix E for a full explanation). PCN allows a network operator to add flow admission and termination for inelastic traffic at the edges of a Diffserv domain, but without any per-flow mechanisms in the interior and without the generous provisioning typical of Diffserv, aiming to significantly reduce costs. The PCN architecture [RFC5559] states that RFC3168 IP in IP tunnelling of the ECN field cannot be used for any tunnel ingress in a PCN domain. Prior to the present specification, this left a stark choice between not being able to use PCN for inelastic traffic control or not being able to use the many tunnels already deployed for Mobile IP, VPNs and so forth. The present specification provides a clean solution to this problem, so that network operators who want to use both PCN and tunnels can specify that every tunnel ingress in a PCN region must comply with this latest specification. Rather than allow tunnel specifications to fragment further into one for PCN, one for IPsec and one for other tunnels, the opportunity has been taken to consolidate the diverging specifications back into a single tunnelling behaviour. Resetting ECN was originally motivated by a covert channel concern that has been deliberately set aside in RFC4301 IPsec. Therefore the reset behaviour of RFC3168 is an anomaly that we do not need to keep. Copying ECN on encapsulation is anyway simpler than resetting. So, as more tunnel endpoints comply Briscoe Expires June 23, 2010 [Page 21]
Internet-Draft ECN Tunnelling December 2009 with this single consistent specification, encapsulation will be simpler as well as more predictable. Appendix B assesses whether copying rather than resetting CE on ingress will cause any unintended side-effects, from the three perspectives of security, control and management. In summary this analysis finds that: o From the control perspective either copying or resetting works for existing arrangements, but copying has more potential for simplifying control and resetting breaks at least one proposal already on the standards track. o From the management and monitoring perspective copying is preferable. o From the traffic security perspective (enforcing congestion control, mitigating denial of service etc) copying is preferable. o From the information security perspective resetting is preferable, but the IETF Security Area now considers copying acceptable given the bandwidth of a 2-bit covert channel can be managed. Therefore there are two points against resetting CE on ingress while copying CE causes no significant harm. 5.3.2. Motivation for Changing Decapsulation The specification for decapsulation in Section 4 fixes three problems with the pre-existing behaviours of both RFC3168 and RFC4301: 1. The pre-existing rules prevented the introduction of alternate ECN semantics to signal more than one severity level of congestion [RFC4774], [RFC5559]. The four states of the 2-bit ECN field provide room for signalling two severity levels in addition to not-congested and not-ECN-capable states. But, the pre-existing rules assumed that two of the states (ECT(0) and ECT(1)) are always equivalent. This unnecessarily restricts the use of one of four codepoints (half a bit) in the IP (v4 & v6) header. The new rules are designed to work in either case; whether ECT(1) is more severe than or equivalent to ECT(0). As explained in Appendix B.1, the original reason for not forwarding the outer ECT codepoints was to limit the covert channel across a decapsulator to 1 bit per packet. However, now that the IETF Security Area has deemed that a 2-bit covert channel through an encapsulator is a manageable risk, the same should be true for a decapsulator. Briscoe Expires June 23, 2010 [Page 22]
Internet-Draft ECN Tunnelling December 2009 As well as being useful for general future-proofing, this problem is immediately pressing for standardisation of pre-congestion notification (PCN), which uses two severity levels of congestion. If a congested queue used ECT(1) in the outer header to signal more severe congestion than ECT(0), the pre-existing decapsulation rules would have thrown away this congestion signal, preventing tunnelled traffic from ever knowing that it should reduce its load. The PCN working group has had to consider a number of wasteful or convoluted work-rounds to this problem (see Appendix D). But by far the simplest approach is just to remove the covert channel blockages from tunnelling behaviour--now deemed unnecessary anyway. Then network operators that want to support two congestion severity-levels for PCN can specify that every tunnel egress in a PCN region must comply with this latest specification. Not only does this make two congestion severity-levels available for PCN standardisation, but also for other potential uses of the extra ECN codepoint (e.g. [VCP]). 2. Cases are documented where a middlebox (e.g. a firewall) drops packets with header values that were currently unused (CU) when the box was deployed, often on the grounds that anything unexpected might be an attack. This tends to bar future use of CU values. The new decapsulation rules specify optional logging and/or alarms for specific combinations of inner and outer header that are currently unused. The aim is to give implementers a recourse other than drop if they are concerned about the security of CU values. It recognises legitimate security concerns about CU values but still eases their future use. If the alarms are interpreted as an attack (e.g. by a management system) the offending packets can be dropped. But alarms can be turned off if these combinations come into regular use (e.g. through a future standards action). 3. While reviewing currently unused combinations of inner and outer, the opportunity was taken to define a single consistent behaviour for the three cases with a Not-ECT inner header but a different outer. RFC3168 and RFC4301 had diverged in this respect. None of these combinations should result from Internet protocols in the RFC series, but future standards actions might put any or all of them to good use. Therefore it was decided that a decapsulator must forward a Not-ECT inner unchanged, even if the arriving outer was ECT(0) or ECT(1). But for safety it should drop a combination of Not-ECT inner and CE outer. Then, if some unfortunate misconfiguration resulted in a congested router Briscoe Expires June 23, 2010 [Page 23]
Internet-Draft ECN Tunnelling December 2009 marking CE on a packet that was originally Not-ECT, drop would be the only appropriate signal for the egress to propagate--the only signal a non-ECN-capable transport (Not-ECT) would understand. A decapsulator can forward a Not-ECT inner unchanged if its outer is ECT(1), even though ECT(1) is being proposed as an intermediate level of congestion in a scheme progressing through the IETF [I-D.ietf-pcn-3-in-1-encoding]. The rationale is to ensure this CU combination will be usable if needed in the future. If any misconfiguration led to ECT(1) congestion signals with a Not-ECT inner, it would not be disastrous for the tunnel egress to suppress them, because the congestion should then escalate to CE marking, which the egress would drop, thus at least preventing congestion collapse. Problems 2 & 3 alone would not warrant a change to decapsulation, but it was decided they are worth fixing and making consistent at the same time as decapsulation code is changed to fix problem 1 (two congestion severity-levels). 6. Backward Compatibility A tunnel endpoint compliant with the present specification is backward compatible when paired with any tunnel endpoint compliant with any previous tunnelling RFC, whether RFC4301, RFC3168 (see Section 3) or the earlier RFCs summarised in Appendix A (RFC2481, RFC2401 and RFC2003). Each case is enumerated below. 6.1. Non-Issues Updating Decapsulation At the egress, this specification only augments the per-packet calculation of the ECN field (RFC3168 and RFC4301) for combinations of inner and outer headers that have so far not been used in any IETF protocols. Therefore, all other things being equal, if an RFC4301 IPsec egress is updated to comply with the new rules, it will still interwork with any RFC4301 compliant ingress and the packet outputs will be identical to those it would have output before (fully backward compatible). And, all other things being equal, if an RFC3168 egress is updated to comply with the same new rules, it will still interwork with any ingress complying with any previous specification (both modes of RFC3168, both modes of RFC2481, RFC2401 and RFC2003) and the packet outputs will be identical to those it would have output before (fully backward compatible). Briscoe Expires June 23, 2010 [Page 24]
Internet-Draft ECN Tunnelling December 2009 A compliant tunnel egress merely needs to implement the one behaviour in Section 4 with no additional mode or option configuration at the ingress or egress nor any additional negotiation with the ingress. The new decapsulation rules have been defined in such a way that congestion control will still work safely if any of the earlier versions of ECN processing are used unilaterally at the encapsulating ingress of the tunnel (any of RFC2003, RFC2401, either mode of RFC2481, either mode of RFC3168, RFC4301 and this present specification). 6.2. Non-Update of RFC4301 IPsec Encapsulation An RFC4301 IPsec ingress can comply with this new specification without any update and it has no need for any new modes, options or configuration. So, all other things being equal, it will continue to interwork identically with any egress it worked with before (fully backward compatible). 6.3. Update to RFC3168 Encapsulation The encapsulation behaviour of the new normal mode copies the ECN field whereas RFC3168 full functionality mode reset it. However, all other things being equal, if RFC3168 ingress is updated to the present specification, the outgoing packets from any tunnel egress will still be unchanged. This is because all variants of tunnelling at either end (RFC4301, both modes of RFC3168, both modes of RFC2481, RFC2401, RFC2003 and the present specification) have always propagated an incoming CE marking through the inner header and onward into the outgoing header, whether the outer header is reset or copied. Therefore, If the tunnel is considered as a black box, the packets output from any egress will be identical with or without an update to the ingress. Nonetheless, if packets are observed within the black box (between the tunnel endpoints), CE markings copied by the updated ingress will be visible within the black box, whereas they would not have been before. Therefore, the update to encapsulation can be termed 'black-box backwards compatible' (i.e. identical unless you look inside the tunnel). This specification introduces no new backward compatibility issues when a compliant ingress talks with a legacy egress, but it has to provide similar safeguards to those already defined in RFC3168. RFC3168 laid down rules to ensure that an RFC3168 ingress turns off ECN (limited functionality mode) if it is paired with a legacy egress (RFC 2481, RFC2401 or RFC2003), which would not propagate ECN correctly. The present specification carries forward those rules (Section 4.3). It uses compatibility mode whenever RFC3168 would have used limited functionality mode, and their per-packet behaviours are identical. Therefore, all other things being equal, an ingress Briscoe Expires June 23, 2010 [Page 25]
Internet-Draft ECN Tunnelling December 2009 using the new rules will interwork with any legacy tunnel egress in exactly the same way as an RFC3168 ingress (still black-box backward compatible). 7. Design Principles for Alternate ECN Tunnelling Semantics This section is informative not normative. S.5 of RFC3168 permits the Diffserv codepoint (DSCP)[RFC2474] to 'switch in' alternative behaviours for marking the ECN field, just as it switches in different per-hop behaviours (PHBs) for scheduling. [RFC4774] gives best current practice for designing such alternative ECN semantics and very briefly mentions in section 5.4 that tunnelling should be considered. The guidance below extends RFC4774, giving additional guidance on designing any alternate ECN semantics that would also require alternate tunnelling semantics. The overriding guidance is: "Avoid designing alternate ECN tunnelling semantics, if at all possible." If a scheme requires tunnels to implement special processing of the ECN field for certain DSCPs, it will be hard to guarantee that every implementer of every tunnel will have added the required exception or that operators will have ubiquitously deployed the required updates. It is unlikely a single authority is even aware of all the tunnels in a network, which may include tunnels set up by applications between endpoints, or dynamically created in the network. Therefore it is highly likely that some tunnels within a network or on hosts connected to it will not implement the required special case. That said, if a non-default scheme for tunnelling the ECN field is really required, the following guidelines may prove useful in its design: On encapsulation in any alternate scheme: 1. The ECN field of the outer header should be cleared to Not-ECT ("00") unless it is guaranteed that the corresponding tunnel egress will correctly propagate congestion markings introduced across the tunnel in the outer header. 2. If it has established that ECN will be correctly propagated, an encapsulator should also copy incoming congestion notification into the outer header. The general principle here is that the outer header should reflect congestion accumulated along the whole upstream path, not just since the tunnel ingress (Appendix B.3 on management and monitoring explains). Briscoe Expires June 23, 2010 [Page 26]
Internet-Draft ECN Tunnelling December 2009 In some circumstances (e.g. pseudowires, PCN), the whole path is divided into segments, each with its own congestion notification and feedback loop. In these cases, the function that regulates load at the start of each segment will need to reset congestion notification for its segment. Often the point where congestion notification is reset will also be located at the start of a tunnel. However, the resetting function should be thought of as being applied to packets after the encapsulation function--two logically separate functions even though they might run on the same physical box. Then the code module doing encapsulation can keep to the copying rule and the load regulator module can reset congestion, without any code in either module being conditional on whether the other is there. On decapsulation in any new scheme: 1. If the arriving inner header is Not-ECT it implies the transport will not understand other ECN codepoints. If the outer header carries an explicit congestion marking, the alternate scheme will probably need to drop the packet--the only indication of congestion the transport will understand. If the outer carries any other ECN codepoint that does not indicate congestion, the alternate scheme can forward the packet, but probably only as Not-ECT. 2. If the arriving inner header is other than Not-ECT, the ECN field that the alternate decapsulation scheme forwards should reflect the more severe congestion marking of the arriving inner and outer headers. 3. Any alternate scheme MUST define a behaviour for all combinations of inner and outer headers, even those that would not be expected to result from standards known at the time and even those that would not be expected from the tunnel ingress paired with the egress at run-time. Consideration should be given to logging such unexpected combinations and raising an alarm, particularly if there is a danger that the invalid combination implies congestion signals are not being propagated correctly. The presence of currently unused combinations may represent an attack, but the new scheme should try to define a way to forward such packets, at least if a safe outgoing codepoint can be defined. Raising an alarm to warn of the possibility of an attack is a preferable approach to dropping that ensures these combinations can be usable in future standards actions. Briscoe Expires June 23, 2010 [Page 27]
Internet-Draft ECN Tunnelling December 2009 IANA Considerations (to be removed on publication): This memo includes no request to IANA. 8. Security Considerations Appendix B.1 discusses the security constraints imposed on ECN tunnel processing. The new rules for ECN tunnel processing (Section 4) trade-off between information security (covert channels) and congestion monitoring & control. In fact, ensuring congestion markings are not lost is itself another aspect of security, because if we allowed congestion notification to be lost, any attempt to enforce a response to congestion would be much harder. Specialist security issues: Tunnels intersecting Diffserv regions with alternate ECN semantics: If alternate congestion notification semantics are defined for a certain Diffserv PHB, the scope of the alternate semantics might typically be bounded by the limits of a Diffserv region or regions, as envisaged in [RFC4774] (e.g. the pre-congestion notification architecture [RFC5559]). The inner headers in tunnels crossing the boundary of such a Diffserv region but ending within the region can potentially leak the external congestion notification semantics into the region, or leak the internal semantics out of the region. [RFC2983] discusses the need for Diffserv traffic conditioning to be applied at these tunnel endpoints as if they are at the edge of the Diffserv region. Similar concerns apply to any processing or propagation of the ECN field at the edges of a Diffserv region with alternate ECN semantics. Such edge processing must also be applied at the endpoints of tunnels with one end inside and the other outside the domain. [RFC5559] gives specific advice on this for the PCN case, but other definitions of alternate semantics will need to discuss the specific security implications in each case. ECN nonce tunnel coverage: The new decapsulation rules improve the coverage of the ECN nonce [RFC3540] relative to the previous rules in RFC3168 and RFC4301. However, nonce coverage is still not perfect, as this would have led to a safety problem in another case. Both are corner-cases, so discussion of the compromise between them is deferred to Appendix F. Covert channel not turned off: A legacy (RFC3168) tunnel ingress could ask an RFC3168 egress to turn off ECN processing as well as itself turning off ECN. An egress compliant with the present specification will agree to such a request from a legacy ingress, but it relies on the ingress solely sending Not-ECT in the outer. Briscoe Expires June 23, 2010 [Page 28]
Internet-Draft ECN Tunnelling December 2009 If the egress receives other ECN codepoints in the outer it will process them as normal, so it will actually still copy congestion markings from the outer to the outgoing header. Referring for example to Figure 5 (Appendix B.1), although the tunnel ingress 'I' will set all ECN fields in outer headers to Not-ECT, 'M' could still toggle CE or ECT(1) on and off to communicate covertly with 'B', because we have specified that 'E' only has one mode regardless of what mode it says it has negotiated. We could have specified that 'E' should have a limited functionality mode and check for such behaviour. But we decided not to add the extra complexity of two modes on a compliant tunnel egress merely to cater for an historic security concern that is now considered manageable. 9. Conclusions This document uses previously unused combinations of inner and outer header to augment the rules for calculating the ECN field when decapsulating IP packets at the egress of IPsec (RFC4301) and non- IPsec (RFC3168) tunnels. In this way it allows tunnels to propagate an extra level of congestion severity. This document also updates the ingress tunnelling encapsulation of RFC3168 ECN to bring all IP in IP tunnels into line with the new behaviour in the IPsec architecture of RFC4301, which copies rather than resets the ECN field when creating outer headers. The need for both these updated behaviours was triggered by the introduction of pre-congestion notification (PCN) onto the IETF standards track. Operators wanting to support PCN or other alternate ECN schemes that use an extra severity level can require that their tunnels comply with the present specification. Nonetheless, as part of general code maintenance, any tunnel can safely be updated to comply with this specification, because it is backward compatible with all previous tunnelling behaviours which will continue to work as before--just using one severity level. The new rules propagate changes to the ECN field across tunnel end- points that previously blocked them to restrict the bandwidth of a potential covert channel. Limiting the channel's bandwidth to 2 bits per packet is now considered sufficient. At the same time as removing these legacy constraints, the opportunity has been taken to draw together diverging tunnel specifications into a single consistent behaviour. Then any tunnel can be deployed unilaterally, and it will support the full range of congestion control and management schemes without any modes or configuration. Further, any host or router can expect the ECN field Briscoe Expires June 23, 2010 [Page 29]
Internet-Draft ECN Tunnelling December 2009 to behave in the same way, whatever type of tunnel might intervene in the path. This new certainty could enable new uses of the ECN field that would otherwise be confounded by ambiguity. 10. Acknowledgements Thanks to Anil Agawaal for pointing out a case where it's safe for a tunnel decapsulator to forward a combination of headers it does not understand. Thanks to David Black for explaining a better way to think about function placement. Also thanks to Arnaud Jacquet for the idea for Appendix C. Thanks to Michael Menth, Bruce Davie, Toby Moncaster, Gorry Fairhurst, Sally Floyd, Alfred Hoenes, Gabriele Corliano, Ingemar Johansson, David Black and Phil Eardley for their thoughts and careful review comments. Bob Briscoe is partly funded by Trilogy, a research project (ICT- 216372) supported by the European Community under its Seventh Framework Programme. The views expressed here are those of the author only. Comments Solicited (to be removed by the RFC Editor): Comments and questions are encouraged and very welcome. They can be addressed to the IETF Transport Area working group mailing list <tsvwg@ietf.org>, and/or to the authors. 11. References 11.1. Normative References [RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003, October 1996. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition of Explicit Congestion Notification (ECN) to IP", RFC 3168, September 2001. [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, December 2005. Briscoe Expires June 23, 2010 [Page 30]
Internet-Draft ECN Tunnelling December 2009 11.2. Informative References [I-D.ietf-pcn-3-in-1-encoding] Briscoe, B. and T. Moncaster, "PCN 3-State Encoding Extension in a single DSCP", draft-ietf-pcn-3-in-1-encoding-00 (work in progress), July 2009. [I-D.ietf-pcn-3-state-encoding] Moncaster, T., Briscoe, B., and M. Menth, "A PCN encoding using 2 DSCPs to provide 3 or more states", draft-ietf-pcn-3-state-encoding-00 (work in progress), April 2009. [I-D.ietf-pcn-psdm-encoding] Menth, M., Babiarz, J., Moncaster, T., and B. Briscoe, "PCN Encoding for Packet-Specific Dual Marking (PSDM)", draft-ietf-pcn-psdm-encoding-00 (work in progress), June 2009. [I-D.ietf-pcn-sm-edge-behaviour] Charny, A., Karagiannis, G., Menth, M., and T. Taylor, "PCN Boundary Node Behaviour for the Single Marking (SM) Mode of Operation", draft-ietf-pcn-sm-edge-behaviour-01 (work in progress), October 2009. [I-D.satoh-pcn-st-marking] Satoh, D., Ueno, H., Maeda, Y., and O. Phanachet, "Single PCN Threshold Marking by using PCN baseline encoding for both admission and termination controls", draft-satoh-pcn-st-marking-02 (work in progress), September 2009. [RFC2401] Kent, S. and R. Atkinson, "Security Architecture for the Internet Protocol", RFC 2401, November 1998. [RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black, "Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers", RFC 2474, December 1998. [RFC2481] Ramakrishnan, K. and S. Floyd, "A Proposal to add Explicit Congestion Briscoe Expires June 23, 2010 [Page 31]
Internet-Draft ECN Tunnelling December 2009 Notification (ECN) to IP", RFC 2481, January 1999. [RFC2983] Black, D., "Differentiated Services and Tunnels", RFC 2983, October 2000. [RFC3540] Spring, N., Wetherall, D., and D. Ely, "Robust Explicit Congestion Notification (ECN) Signaling with Nonces", RFC 3540, June 2003. [RFC4306] Kaufman, C., "Internet Key Exchange (IKEv2) Protocol", RFC 4306, December 2005. [RFC4774] Floyd, S., "Specifying Alternate Semantics for the Explicit Congestion Notification (ECN) Field", BCP 124, RFC 4774, November 2006. [RFC5129] Davie, B., Briscoe, B., and J. Tay, "Explicit Congestion Marking in MPLS", RFC 5129, January 2008. [RFC5559] Eardley, P., "Pre-Congestion Notification (PCN) Architecture", RFC 5559, June 2009. [RFC5670] Eardley, P., "Metering and Marking Behaviour of PCN-Nodes", RFC 5670, November 2009. [RFC5696] Moncaster, T., Briscoe, B., and M. Menth, "Baseline Encoding and Transport of Pre-Congestion Information", RFC 5696, November 2009. [VCP] Xia, Y., Subramanian, L., Stoica, I., and S. Kalyanaraman, "One more bit is enough", Proc. SIGCOMM'05, ACM CCR 35(4)37--48, 2005, <http:// doi.acm.org/10.1145/ 1080091.1080098>. Briscoe Expires June 23, 2010 [Page 32]
Internet-Draft ECN Tunnelling December 2009 Appendix A. Early ECN Tunnelling RFCs IP in IP tunnelling was originally defined in [RFC2003]. On encapsulation, the incoming header was copied to the outer and on decapsulation the outer was simply discarded. Initially, IPsec tunnelling [RFC2401] followed the same behaviour. When ECN was introduced experimentally in [RFC2481], legacy (RFC2003 or RFC2401) tunnels would have discarded any congestion markings added to the outer header, so RFC2481 introduced rules for calculating the outgoing header from a combination of the inner and outer on decapsulation. RC2481 also introduced a second mode for IPsec tunnels, which turned off ECN processing (Not-ECT) in the outer header on encapsulation because an RFC2401 decapsulator would discard the outer on decapsulation. For RFC2401 IPsec this had the side- effect of completely blocking the covert channel. In RFC2481 the ECN field was defined as two separate bits. But when ECN moved from the experimental to the standards track [RFC3168], the ECN field was redefined as four codepoints. This required a different calculation of the ECN field from that used in RFC2481 on decapsulation. RFC3168 also had two modes; a 'full functionality mode' that restricted the covert channel as much as possible but still allowed ECN to be used with IPsec, and another that completely turned off ECN processing across the tunnel. This 'limited functionality mode' both offered a way for operators to completely block the covert channel and allowed an RFC3168 ingress to interwork with a legacy tunnel egress (RFC2481, RFC2401 or RFC2003). The present specification includes a similar compatibility mode to interwork safely with tunnels compliant with any of these three earlier RFCs. However, unlike RFC3168, it is only a mode of the ingress, as decapsulation behaviour is the same in either case. Appendix B. Design Constraints Tunnel processing of a congestion notification field has to meet congestion control and management needs without creating new information security vulnerabilities (if information security is required). This appendix documents the analysis of the tradeoffs between these factors that led to the new encapsulation rules in Section 4.1. B.1. Security Constraints Information security can be assured by using various end to end security solutions (including IPsec in transport mode [RFC4301]), but a commonly used scenario involves the need to communicate between two Briscoe Expires June 23, 2010 [Page 33]
Internet-Draft ECN Tunnelling December 2009 physically protected domains across the public Internet. In this case there are certain management advantages to using IPsec in tunnel mode solely across the publicly accessible part of the path. The path followed by a packet then crosses security 'domains'; the ones protected by physical or other means before and after the tunnel and the one protected by an IPsec tunnel across the otherwise unprotected domain. We will use the scenario in Figure 5 where endpoints 'A' and 'B' communicate through a tunnel. The tunnel ingress 'I' and egress 'E' are within physically protected edge domains, while the tunnel spans an unprotected internetwork where there may be 'men in the middle', M. physically unprotected physically <-protected domain-><--domain--><-protected domain-> +------------------+ +------------------+ | | M | | | A-------->I=========>==========>E-------->B | | | | | +------------------+ +------------------+ <----IPsec secured----> tunnel Figure 5: IPsec Tunnel Scenario IPsec encryption is typically used to prevent 'M' seeing messages from 'A' to 'B'. IPsec authentication is used to prevent 'M' masquerading as the sender of messages from 'A' to 'B' or altering their contents. In addition 'I' can use IPsec tunnel mode to allow 'A' to communicate with 'B', but impose encryption to prevent 'A' leaking information to 'M'. Or 'E' can insist that 'I' uses tunnel mode authentication to prevent 'M' communicating information to 'B'. Mutable IP header fields such as the ECN field (as well as the TTL/ Hop Limit and DS fields) cannot be included in the cryptographic calculations of IPsec. Therefore, if 'I' copies these mutable fields into the outer header that is exposed across the tunnel it will have allowed a covert channel from 'A' to M that bypasses its encryption of the inner header. And if 'E' copies these fields from the outer header to the inner, even if it validates authentication from 'I', it will have allowed a covert channel from 'M' to 'B'. ECN at the IP layer is designed to carry information about congestion from a congested resource towards downstream nodes. Typically a downstream transport might feed the information back somehow to the point upstream of the congestion that can regulate the load on the congested resource, but other actions are possible (see [RFC3168] S.6). In terms of the above unicast scenario, ECN effectively intends to create an information channel (for congestion signalling) Briscoe Expires June 23, 2010 [Page 34]
Internet-Draft ECN Tunnelling December 2009 from 'M' to 'B' (for 'B' to feed back to 'A'). Therefore the goals of IPsec and ECN are mutually incompatible, requiring some compromise. With respect to the DS or ECN fields, S.5.1.2 of RFC4301 says, "controls are provided to manage the bandwidth of this [covert] channel". Using the ECN processing rules of RFC4301, the channel bandwidth is two bits per datagram from 'A' to 'M' and one bit per datagram from 'M' to 'A' (because 'E' limits the combinations of the 2-bit ECN field that it will copy). In both cases the covert channel bandwidth is further reduced by noise from any real congestion marking. RFC4301 implies that these covert channels are sufficiently limited to be considered a manageable threat. However, with respect to the larger (6b) DS field, the same section of RFC4301 says not copying is the default, but a configuration option can allow copying "to allow a local administrator to decide whether the covert channel provided by copying these bits outweighs the benefits of copying". Of course, an administrator considering copying of the DS field has to take into account that it could be concatenated with the ECN field giving an 8b per datagram covert channel. For tunnelling the 6b Diffserv field two conceptual models have had to be defined so that administrators can trade off security against the needs of traffic conditioning [RFC2983]: The uniform model: where the Diffserv field is preserved end-to-end by copying into the outer header on encapsulation and copying from the outer header on decapsulation. The pipe model: where the outer header is independent of that in the inner header so it hides the Diffserv field of the inner header from any interaction with nodes along the tunnel. However, for ECN, the new IPsec security architecture in RFC4301 only standardised one tunnelling model equivalent to the uniform model. It deemed that simplicity was more important than allowing administrators the option of a tiny increment in security, especially given not copying congestion indications could seriously harm everyone's network service. B.2. Control Constraints Congestion control requires that any congestion notification marked into packets by a resource will be able to traverse a feedback loop back to a function capable of controlling the load on that resource. To be precise, rather than calling this function the data source, we will call it the Load Regulator. This will allow us to deal with exceptional cases where load is not regulated by the data source, but Briscoe Expires June 23, 2010 [Page 35]
Internet-Draft ECN Tunnelling December 2009 usually the two terms will be synonymous. Note the term "a function _capable of_ controlling the load" deliberately includes a source application that doesn't actually control the load but ought to (e.g. an application without congestion control that uses UDP). A--->R--->I=========>M=========>E-------->B Figure 6: Simple Tunnel Scenario We now consider a similar tunnelling scenario to the IPsec one just described, but without the different security domains so we can just focus on ensuring the control loop and management monitoring can work (Figure 6). If we want resources in the tunnel to be able to explicitly notify congestion and the feedback path is from 'B' to 'A', it will certainly be necessary for 'E' to copy any CE marking from the outer header to the inner header for onward transmission to 'B', otherwise congestion notification from resources like 'M' cannot be fed back to the Load Regulator ('A'). But it does not seem necessary for 'I' to copy CE markings from the inner to the outer header. For instance, if resource 'R' is congested, it can send congestion information to 'B' using the congestion field in the inner header without 'I' copying the congestion field into the outer header and 'E' copying it back to the inner header. 'E' can still write any additional congestion marking introduced across the tunnel into the congestion field of the inner header. All this shows that 'E' can preserve the control loop irrespective of whether 'I' copies congestion notification into the outer header or resets it. That is the situation for existing control arrangements but, because copying reveals more information, it would open up possibilities for better control system designs. For instance, Appendix E describes how resetting CE marking on encapsulation breaks a proposed congestion marking scheme on the standards track. It ends up removing excessive amounts of traffic unnecessarily. Whereas copying CE markings at ingress leads to the correct control behaviour. B.3. Management Constraints As well as control, there are also management constraints. Specifically, a management system may monitor congestion markings in passing packets, perhaps at the border between networks as part of a service level agreement. For instance, monitors at the borders of autonomous systems may need to measure how much congestion has accumulated so far along the path, perhaps to determine between them Briscoe Expires June 23, 2010 [Page 36]
Internet-Draft ECN Tunnelling December 2009 how much of the congestion is contributed by each domain. In this document we define the baseline of congestion marking (or the Congestion Baseline) as the source of the layer that created (or most recently reset) the congestion notification field. When monitoring congestion it would be desirable if the Congestion Baseline did not depend on whether packets were tunnelled or not. Given some tunnels cross domain borders (e.g. consider M in Figure 6 is monitoring a border), it would therefore be desirable for 'I' to copy congestion accumulated so far into the outer headers, so that it is exposed across the tunnel. For management purposes it might be useful for the tunnel egress to be able to monitor whether congestion occurred across a tunnel or upstream of it. Superficially it appears that copying congestion markings at the ingress would make this difficult, whereas it was straightforward when an RFC3168 ingress reset them. However, Appendix C gives a simple and precise method for a tunnel egress to infer the congestion level introduced across a tunnel. It works irrespective of whether the ingress copies or resets congestion markings. Appendix C. Contribution to Congestion across a Tunnel This specification mandates that a tunnel ingress determines the ECN field of each new outer tunnel header by copying the arriving header. Concern has been expressed that this will make it difficult for the tunnel egress to monitor congestion introduced only along a tunnel, which is easy if the outer ECN field is reset at a tunnel ingress (RFC3168 full functionality mode). However, in fact copying CE marks at ingress will still make it easy for the egress to measure congestion introduced across a tunnel, as illustrated below. Consider 100 packets measured at the egress. Say it measures that 30 are CE marked in the inner and outer headers and 12 have additional CE marks in the outer but not the inner. This means packets arriving at the ingress had already experienced 30% congestion. However, it does not mean there was 12% congestion across the tunnel. The correct calculation of congestion across the tunnel is p_t = 12/ (100-30) = 12/70 = 17%. This is easy for the egress to measure. It is simply the proportion of packets not marked in the inner header (70) that have a CE marking in the outer header (12). This technique works whether the ingress copies or resets CE markings, so it can be used by an egress that is not sure which RFC the ingress complies with. Figure 7 illustrates this in a combinatorial probability diagram. The square represents 100 packets. The 30% division along the bottom Briscoe Expires June 23, 2010 [Page 37]
Internet-Draft ECN Tunnelling December 2009 represents marking before the ingress, and the p_t division up the side represents marking introduced across the tunnel. ^ outer header marking | 100% +-----+---------+ The large square | | | represents 100 packets | 30 | | | | | p_t = 12/(100-30) p_t + +---------+ = 12/70 | | 12 | = 17% 0 +-----+---------+---> 0 30% 100% inner header marking Figure 7: Tunnel Marking of Packets Already Marked at Ingress Appendix D. Why Losing ECT(1) on Decapsulation Impedes PCN Congestion notification with two severity levels is currently on the IETF's standards track agenda in the Congestion and Pre-Congestion Notification (PCN) working group. PCN needs all four possible states of congestion signalling in the 2-bit ECN field to be propagated at the egress, but pre-existing tunnels only propagate three. The four PCN states are: not PCN-enabled, not marked and two increasingly severe levels of congestion marking. The less severe marking means 'stop admitting new traffic' and the more severe marking means 'terminate some existing flows', which may be needed after reroutes (see [RFC5559] for more details). (Note on terminology: wherever this document counts four congestion states, the PCN working group would count this as three PCN states plus a not-PCN-enabled state.) Figure 2 (Section 3.2) shows that pre-existing decapsulation behaviour would have discarded any ECT(1) markings in outer headers if the inner was ECT(0). This prevented the PCN working group from using ECT(1) -- if a PCN node used ECT(1) to indicate one of the severity levels of congestion, any later tunnel egress would revert the marking to ECT(0) as if nothing had happened. Effectively the decapsulation rules of RFC4301 and RFC3168 waste one ECT codepoint; they treat the ECT(0) and ECT(1) codepoints as a single codepoint. A number of work-rounds to this problem were proposed in the PCN w-g; to add the fourth state another way or avoid needing it. Without wishing to disparage the ingenuity of these work-rounds, none were chosen for the standards track because they were either somewhat wasteful, imprecise or complicated: o One uses a pair of Diffserv codepoint(s) in place of each PCN DSCP to encode the extra state [I-D.ietf-pcn-3-state-encoding], using Briscoe Expires June 23, 2010 [Page 38]
Internet-Draft ECN Tunnelling December 2009 up the rapidly exhausting DSCP space while leaving an ECN codepoint unused. o Another survives tunnelling without an extra DSCP [I-D.ietf-pcn-psdm-encoding], but it requires the PCN edge gateways to share the initial state of a packet out of band. o Another proposes a more involved marking algorithm in forwarding elements to encode the three congestion notification states using only two ECN codepoints [I-D.satoh-pcn-st-marking]. o Another takes a different approach; it compromises the precision of the admission control mechanism in some network scenarios, but manages to work with just three encoding states and a single marking algorithm [I-D.ietf-pcn-sm-edge-behaviour]. Rather than require the IETF to bless any of these experimental encoding work-rounds, the present specification fixes the root cause of the problem so that operators deploying PCN can simply require that tunnel end-points within a PCN region should comply with this new ECN tunnelling specification. On the public Internet it would not be possible to know whether all tunnels complied with this new specification, but universal compliance is feasible for PCN, because it is intended to be deployed in a controlled Diffserv region. Given the present specification, the PCN w-g could progress a trivially simple four-state ECN encoding [I-D.ietf-pcn-3-in-1-encoding]. This would replace the interim standards track baseline encoding of just three states [RFC5696] which makes a fourth state available for any of the experimental alternatives. Appendix E. Why Resetting ECN on Encapsulation Impedes PCN The PCN architecture says "...if encapsulation is done within the PCN-domain: Any PCN-marking is copied into the outer header. Note: A tunnel will not provide this behaviour if it complies with [RFC3168] tunnelling in either mode, but it will if it complies with [RFC4301] IPsec tunnelling. " The specific issue here concerns PCN excess rate marking [RFC5670]. The purpose of excess rate marking is to provide a bulk mechanism for interior nodes within a PCN domain to mark traffic that is exceeding a configured threshold bit-rate, perhaps after an unexpected event such as a reroute, a link or node failure, or a more widespread disaster. Reroutes are a common cause of QoS degradation in IP networks. After reroutes it is common for multiple links in a network to become stressed at once. Therefore, PCN excess rate Briscoe Expires June 23, 2010 [Page 39]
Internet-Draft ECN Tunnelling December 2009 marking has been carefully designed to ensure traffic marked at one queue will not be counted again for marking at subsequent queues (see the `Excess traffic meter function' of [RFC5670]). However, if an RFC3168 tunnel ingress intervenes, it resets the ECN field in all the outer headers. This will cause excess traffic to be counted more than once, leading to many flows being removed that did not need to be removed at all. This is why the an RFC3168 tunnel ingress cannot be used in a PCN domain. The ECN reset in RFC3168 is no longer deemed necessary, it is inconsistent with RFC4301, it is not as simple as RFC4301 and it is impeding deployment of new protocols like PCN. The present specification corrects this perverse situation. Appendix F. Compromise on Decap with ECT(1) Inner and ECT(0) Outer A packet with an ECT(1) inner and an ECT(0) outer should never arise from any known IETF protocol. Without giving a reason, RFC3168 and RFC4301 both say the outer should be ignored when decapsulating such a packet. This appendix explains why it was decided not to change this advice. In summary, ECT(0) always means 'not congested' and ECT(1) may imply the same [RFC3168] or it may imply a higher severity congestion signal [RFC4774], [I-D.ietf-pcn-3-in-1-encoding], depending on the transport in use. Whether they mean the same or not, at the ingress the outer should have started the same as the inner and only a broken or compromised router could have changed the outer to ECT(0). The decapsulator can detect this anomaly. But the question is, should it correct the anomaly by ignoring the outer, or should it reveal the anomaly to the end-to-end transport by forwarding the outer? On balance, it was decided that the decapsulator should correct the anomaly, but log the event and optionally raise an alarm. This is the safe action if ECT(1) is being used as a more severe marking than ECT(0), because it passes the more severe signal to the transport. However, it is not a good idea to hide anomalies, which is why an optional alarm is suggested. It should be noted that this anomaly may be the result of two changes to the outer: a broken or compromised router within the tunnel might be erasing congestion markings introduced earlier in the same tunnel by a congested router. In this case, the anomaly would be losing congestion signals, which needs immediate attention. The original reason for defining ECT(0) and ECT(1) as equivalent was Briscoe Expires June 23, 2010 [Page 40]
Internet-Draft ECN Tunnelling December 2009 so that the data source could use the ECN nonce [RFC3540] to detect if congestion signals were being erased. However, in this case, the decapsulator does not need a nonce to detect any anomalies introduced within the tunnel, because it has the inner as a record of the header at the ingress. Therefore, it was decided that the best compromise would be to give precedence to solving the safety issue over revealing the anomaly, because the anomaly could at least be detected and dealt with internally. Superficially, the opposite case where the inner and outer carry different ECT values, but with an ECT(1) outer and ECT(0) inner, seems to require a similar compromise. However, because that case is reversed, no compromise is necessary; it is best to forward the outer whether the transport expects the ECT(1) to mean a higher severity than ECT(0) or the same severity. Forwarding the outer either preserves a higher value (if it is higher) or it reveals an anomaly to the transport (if the two ECT codepoints mean the same severity). Appendix G. Open Issues The new decapsulation behaviour defined in Section 4.2 adds support for propagation of 2 severity levels of congestion. However transports have no way to discover whether there are any legacy tunnels on their path that will not propagate 2 severity levels. It would have been nice to add a feature for transports to check path support, but this remains an open issue that will have to be addressed in any future standards action to define an end-to-end scheme that requires 2-severity levels of congestion. PCN avoids this problem, because it is only for a controlled region, so all legacy tunnels can be upgraded by the same operator that deploys PCN. Author's Address Bob Briscoe BT B54/77, Adastral Park Martlesham Heath Ipswich IP5 3RE UK Phone: +44 1473 645196 EMail: bob.briscoe@bt.com URI: http://bobbriscoe.net/ Briscoe Expires June 23, 2010 [Page 41]
