Individual Submission J. Korhonen, Ed.
Internet-Draft Nokia Siemens Networks
Intended status: Informational J. Soininen
Expires: January 12, 2012 Renesas Mobile
B. Patil
T. Savolainen
G. Bajko
Nokia
K. Iisakkila
Renesas Mobile
July 11, 2011
IPv6 in 3GPP Evolved Packet System
draft-ietf-v6ops-3gpp-eps-03
Abstract
Use of data services in smart phones and broadband services via HSPA
and HSPA+, in particular Internet services, has increased rapidly and
operators that have deployed networks based on 3GPP network
architectures are facing IPv4 address shortages at the Internet
registries and are feeling a pressure to migrate to IPv6. This
document describes the support for IPv6 in 3GPP network
architectures.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 12, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
Korhonen, et al. Expires January 12, 2012 [Page 1]
Internet-Draft IPv6 in 3GPP EPS July 2011
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. 3GPP Terminology and Concepts . . . . . . . . . . . . . . . . 5
2.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 5
2.2. The concept of APN . . . . . . . . . . . . . . . . . . . . 9
3. IP over 3GPP GPRS . . . . . . . . . . . . . . . . . . . . . . 10
3.1. Introduction to 3GPP GPRS . . . . . . . . . . . . . . . . 10
3.2. PDP Context . . . . . . . . . . . . . . . . . . . . . . . 12
4. IP over 3GPP EPS . . . . . . . . . . . . . . . . . . . . . . . 12
4.1. Introduction to 3GPP EPS . . . . . . . . . . . . . . . . . 13
4.2. PDN Connection . . . . . . . . . . . . . . . . . . . . . . 14
4.3. EPS bearer model . . . . . . . . . . . . . . . . . . . . . 14
5. Address Management . . . . . . . . . . . . . . . . . . . . . . 15
5.1. IPv4 Address Configuration . . . . . . . . . . . . . . . . 15
5.2. IPv6 Address Configuration . . . . . . . . . . . . . . . . 15
5.3. Prefix Delegation . . . . . . . . . . . . . . . . . . . . 16
5.4. IPv6 Neighbor Discovery Considerations . . . . . . . . . . 16
6. 3GPP Dual-Stack Approach to IPv6 . . . . . . . . . . . . . . . 17
6.1. 3GPP Networks Prior to Release-8 . . . . . . . . . . . . . 17
6.2. 3GPP Release-8 and -9 Networks . . . . . . . . . . . . . . 18
6.3. PDN Connection Establishment Process . . . . . . . . . . . 19
6.4. Mobility of 3GPP IPv4v6 Type of Bearers . . . . . . . . . 22
7. Dual-Stack Approach to IPv6 Transition in 3GPP Networks . . . 22
8. Deployment issues . . . . . . . . . . . . . . . . . . . . . . 23
8.1. Overlapping IPv4 Addresses . . . . . . . . . . . . . . . . 23
8.2. IPv6 for transport . . . . . . . . . . . . . . . . . . . . 24
8.3. Operational Aspects of Running Dual-Stack Networks . . . . 25
8.4. Operational Aspects of Running a Network with
IPv6-only Bearers . . . . . . . . . . . . . . . . . . . . 25
8.5. Restricting Outbound IPv6 Roaming . . . . . . . . . . . . 26
8.6. Inter-RAT Handovers and IP Versions . . . . . . . . . . . 27
8.7. Provisioning of IPv6 Subscribers and Various
Combinations During Initial Network Attachment . . . . . . 28
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 30
10. Security Considerations . . . . . . . . . . . . . . . . . . . 30
11. Summary and Conclusion . . . . . . . . . . . . . . . . . . . . 30
Korhonen, et al. Expires January 12, 2012 [Page 2]
Internet-Draft IPv6 in 3GPP EPS July 2011
12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 30
13. Informative References . . . . . . . . . . . . . . . . . . . . 30
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 32
Korhonen, et al. Expires January 12, 2012 [Page 3]
Internet-Draft IPv6 in 3GPP EPS July 2011
1. Introduction
IPv6 has been specified in the 3rd Generation Partnership Project
(3GPP) standards since the early architectures developed for R99
General Packet Radio Service (GPRS). However, the support for IPv6
in commercially deployed networks remains low. There are many
factors that can be attributed to the lack of IPv6 deployment in 3GPP
networks. The most relevant one is essentially the same as the
reason for IPv6 not being deployed by other networks as well, i.e.
the lack of business and commercial incentives for deployment. 3GPP
network architectures have also evolved since 1999 (since R99). The
most recent version of the 3GPP architecture, the Evolved Packet
System (EPS), which is commonly referred to as SAE, LTE or Release-8,
is a packet centric architecture. The number of subscribers and
devices that are using the 3GPP networks for Internet connectivity
and data services has also increased significantly. With the
subscriber growth numbers projected to increase even further and the
IPv4 addresses depletion problem looming in the near term, 3GPP
operators and vendors have started the process of identifying the
scenarios and solutions needed to transition to IPv6.
This document describes the establishment of IP connectivity in 3GPP
network architectures, specifically in the context of IP bearers for
3GPP GPRS and for 3GPP EPS. It provides an overview of how IPv6 is
supported as per the current set of 3GPP specifications. Some of the
issues and concerns with respect to deployment and shortage of
private IPv4 addresses within a single network domain are also
discussed.
The IETF has specified a set of tools and mechanisms that can be
utilized for transitioning to IPv6. In addition to operating dual-
stack networks during the transition from IPv4 to IPv6 phase, the two
alternative categories for the transition are encapsulation and
translation. The IETF continues to specify additional solutions for
enabling the transition based on the deployment scenarios and
operator/ISP requirements. There is no single approach for
transition to IPv6 that can meet the needs for all deployments and
models. The 3GPP scenarios for transition, described in [TR.23975],
can be addressed using transition mechanisms that are already
available in the toolbox. The objective of transition to IPv6 in
3GPP networks is to ensure that:
1. Legacy devices and hosts which have an IPv4-only stack will
continue to be provided with IP connectivity to the Internet and
services,
2. Devices which are dual-stack can access the Internet either via
IPv6 or IPv4. The choice of using IPv6 or IPv4 depends on the
Korhonen, et al. Expires January 12, 2012 [Page 4]
Internet-Draft IPv6 in 3GPP EPS July 2011
capability of:
A. the application on the host,
B. the support for IPv4 and IPv6 bearers by the network and/or,
C. the capability of the server(s) and other end points.
3GPP networks are capable of providing a host with IPv4 and IPv6
connectivity today, albeit in many cases with upgrades to network
elements such as the SGSN and GGSN.
2. 3GPP Terminology and Concepts
2.1. Terminology
Access Point Name
Access Point Name (APN) is a fully qualified domain name and
resolves to a specific gateway in an operators network. The APNs
are piggybacked on the administration of the DNS namespace.
Dual Address PDN/PDP Type
The Dual Address PDN/PDP Type (IPv4v6) is used in 3GPP context in
many cases as a synonym for dual-stack i.e. a connection type
capable of serving both IPv4 and IPv6 simultaneously.
Evolved Packet Core
Evolved Packet Core (EPC) is an evolution of the 3GPP GPRS system
characterized by higher-data-rate, lower-latency, packet-optimized
system. EPC comprises of subcomponents such as Mobility
Management Entity (MME), Serving Gateway (SGW), Packet Data
Network Gateway (PDN-GW) and Home Subscriber Server (HSS).
Evolved Packet System
Evolved Packet System (EPS) is an evolution of the 3GPP GPRS
system characterized by higher-data-rate, lower-latency, packet-
optimized system that supports multiple Radio Access Technologies
(RAT). The EPS comprises the Evolved Packet Core (EPC) together
with the evolved radio access network (E-UTRA and E-UTRAN).
Korhonen, et al. Expires January 12, 2012 [Page 5]
Internet-Draft IPv6 in 3GPP EPS July 2011
Evolved UTRAN
Evolved UTRAN (E-UTRAN) is communications network, sometimes
referred to as 4G, and consists of eNodeBs (4G base station) which
make up the E-UTRAN radio access network. The E-UTRAN allows
connectivity between the mobile host/device and the core network.
GPRS tunnelling protocol
GPRS Tunnelling Protocol (GTP) [TS.29060] [TS.29274] is a
tunnelling protocol defined by 3GPP. It is a network based
mobility protocol and similar to Proxy Mobile IPv6 (PMIPv6)
[RFC5213]. However, GTP also provides functionality beyond
mobility such as inband signaling related to Quality of Service
(QoS) and charging among others.
GSM EDGE Radio Access Network
GSM EDGE Radio Access Network (GERAN) is communications network,
commonly referred to as 2G or 2.5G, and consists of base stations
and Base Station Controllers (BSC) which make up the GSM EDGE
radio access network. The GERAN allows connectivity between the
mobile host/device and the core network.
Gateway GPRS Support Node
Gateway GPRS Support Node (GGSN) is a gateway function in GPRS,
which provides connectivity to Internet or other PDNs. The host
attaches to a GGSN identified by an APN assigned to it by an
operator. The GGSN also serves as the topological anchor for
addresses/prefixes assigned to the mobile host.
General Packet Radio Service
General Packet Radio Service (GPRS) is a packet oriented mobile
data service available to users of the 2G and 3G cellular
communication systems Global System for Mobile communications
(GSM), and specified by 3GPP.
High Speed Packet Access
The High Speed Packet Access (HSPA) and the Evolved High Speed
Packet Access (HSPA+) are enhanced versions of the WCDMA and
UTRAN, thus providing more data throughput and lower latencies.
Korhonen, et al. Expires January 12, 2012 [Page 6]
Internet-Draft IPv6 in 3GPP EPS July 2011
Home Location Register
The Home Location Register (HLR) is a pre-Release-5 database (but
is also used in Release-5 and later networks in real deployments)
that contains subscriber data and call routing related
information. Every subscriber of an operator including
subscribers' enabled services are provisioned in the HLR.
Home Subscriber Server
The Home Subscriber Server (HSS) is a database for a given
subscriber and got introduced in 3GPP Release-5. It is the entity
containing the subscription-related information to support the
network entities actually handling calls/sessions.
Mobility Management Entity
Mobility Management Entity (MME) is a network element that is
responsible for control plane functionalities, including
authentication, authorization, bearer management, layer-2
mobility, etc. The MME is essentially the control plane part of
the SGSN in GPRS. The user plane traffic bypasses the MME.
Mobile Terminal
The Mobile Terminal (MT) is the modem and the radio part of the
Mobile Station (MS).
Public Land Mobile Network
The Public Land Mobile Network (PLMN) is a network that is
operated by a single administration. A PLMN (and therefore also
an operator) is identified by the Mobile Country Code (MCC) and
the Mobile Network Code (MNC). Each (telecommunications) operator
providing mobile services has its own PLMN.
Policy and Charging Control
The Policy and Charging Control (PCC) framework is used for QoS
policy and charging control. It has two main functions: flow
based charging including online credit control, and policy control
(e.g. gating control, QoS control and QoS signaling). It is
optional to 3GPP EPS but needed if dynamic policy and charging
control by means of PCC rules based on user and services are
desired.
Korhonen, et al. Expires January 12, 2012 [Page 7]
Internet-Draft IPv6 in 3GPP EPS July 2011
Packet Data Network
Packet Data Network (PDN) is a packet based network that either
belongs to the operator or is an external network such as Internet
and corporate intranet. The user eventually accesses services in
one or more PDNs. The operator's packet core network are
separated from packet data networks either by GGSNs or PDN
Gateways (PDN-GW).
Packet Data Network Gateway
Packet Data Network Gateway (PDN-GW) is a gateway function in
Evolved Packet System (EPS), which provides connectivity to
Internet or other PDNs. The host attaches to a PDN-GW identified
by an APN assigned to it by an operator. The PDN-GW also serves
as the topological anchor for addresses/prefixes assigned to the
mobile host.
Packet Data Protocol Context
A Packet Data Protocol (PDP) Context is the equivalent of a
virtual connection between the host and a gateway.
S4 Serving Gateway Support Node
S4 Serving Gateway Support Node (S4-SGSN) is a Release-8 (and
onwards) compliant SGSN that connects 2G/3G radio access network
to EPC via new Release-8 interfaces like S3, S4, and S6d.
Serving Gateway
Serving Gateway (SGW) is a gateway function in EPS, which
terminates the interface towards E-UTRAN. The SGW is the Mobility
Anchor point for layer-2 mobility (inter-eNodeB handovers). For
each User Equipment connected with the EPS, at any given point of
time, there is only one SGW. The SGW is essentially the user
plane part of the GPRS' SGSN forwarding packets between a PDN-GW.
Serving Gateway Support Node
Serving Gateway Support Node (SGSN) is a network element that is
located between the radio access network (RAN) and the gateway
(GGSN). A per mobile host point to point (p2p) tunnel between the
GGSN and SGSN transports the packets between the mobile host and
the gateway.
Korhonen, et al. Expires January 12, 2012 [Page 8]
Internet-Draft IPv6 in 3GPP EPS July 2011
Terminal Equipment
The Terminal Equipment (TE) is any device/host connected to the
Mobile Terminal (MT) offering services to the use. A TE may
communicate to a MT, for example, over Point to Point Protocol
(PPP).
UE, MS, MN and Mobile
The terms UE (User Equipment), MS (Mobile Station), MN (Mobile
Node) and, mobile refer to the devices which are hosts with
ability to obtain Internet connectivity via a 3GPP network. A MS
comprises of a Terminal Equipment (TE) and a Mobile Terminal (MT).
The terms UE, MS, MN and devices are used interchangeably within
this document.
UMTS Terrestrial Radio Access Network
UMTS Terrestrial Radio Access Network (UTRAN) is communications
network, commonly referred to as 3G, and consists of NodeBs (3G
base station) and Radio Network Controllers (RNC) which make up
the UMTS radio access network. The UTRAN allows connectivity
between the mobile host/device and the core network. UTRAN
comprises of WCDMA, HSPA and HSPA+ radio technologies.
Wideband Code Division Multiple Access
The Wideband Code Division Multiple Access (WCDMA) is the radio
interface used in UMTS networks.
eNodeB
The eNodeB is a base station entity that supports the Long Term
Evolution (LTE) air interface.
2.2. The concept of APN
The Access Point Name (APN) essentially refers to a gateway in the
3GPP network. The 'complete' APN is expressed in a form of a Fully
Qualified Domain Name (FQDN) and also piggybacked on the
administration of the DNS namespace, thus effectively allowing the
discovery of gateways using the DNS. Mobile hosts/devices can choose
to attach to a specific gateway in the packet core. The gateway
provides connectivity to the Packet Data Network (PDN) such as the
Internet. An operator may also include gateways which do not provide
Internet connectivity, rather a connectivity to closed network
providing a set of operator's own services. A mobile host/device can
be attached to one or more gateways simultaneously. The gateway in a
Korhonen, et al. Expires January 12, 2012 [Page 9]
Internet-Draft IPv6 in 3GPP EPS July 2011
3GPP network is the GGSN or PDN-GW. Figure 1 below illustrates the
APN-based network connectivity concept.
.--.
_(. `)
.--. +------------+ _( PDN `)_
_(Core`. |GW1 |====( Internet `)
+---+ ( NW )------|APN=internet| ( ` . ) )
[MN]~~~~|RAN|----( ` . ) )--+ +------------+ `--(_______)---'
^ +---+ `--(___.-' |
| | .--.
| | +----------+ _(.PDN`)
| +--|GW2 | _(Operator`)_
| |APN=OpServ|====( Services `)
MN is attached +----------+ ( ` . ) )
to GW1 and GW2 `--(_______)---'
simultaneously
Figure 1: Mobile host/device attached to multiple APNs simultaneously
3. IP over 3GPP GPRS
3.1. Introduction to 3GPP GPRS
A simplified 2G/3G GPRS architecture is illustrated in Figure 2.
This architecture basically covers the GPRS core network since R99 to
Release-7, and radio access technologies such as GSM (2G), EDGE (2G,
often referred as 2.5G), WCDMA (3G) and HSPA(+) (3G, often referred
as 3.5G). The architecture shares obvious similarities with the
Evolved Packet System (EPS) as will be seen in Section 4. Based on
Gn/Gp interfaces, the GPRS core network functionality is logically
implemented on two network nodes, the SGSN and the GGSN.
Korhonen, et al. Expires January 12, 2012 [Page 10]
Internet-Draft IPv6 in 3GPP EPS July 2011
3G .--.
Uu +-----+ Iu +----+ +----+ _( `.
[TE]+[MT]~~|~~~|UTRAN|--|---|SGSN|--|---|GGSN|--|----( PDN )
+-----+ +----+ Gn +----+ Gi ( ` . ) )
/ | `--(___.-'
2G Gb-- |
+---+ / --Gp
[TE]+[MT]~~|~~~|BSS|___/ |
Um +---+ .--.
_(. `)
_( [GGSN] `)_
( other `)
( ` . PLMN ) )
`--(_______)---'
Figure 2: Overview of the 2G/3G GPRS Logical Architecture
Gn/Gp: These interfaces provide a network based mobility service for
a mobile host and are used between a SGSN and a GGSN. The Gn
interface is used when GGSN and SGSN are located inside one
operator (i.e. PLMN). The Gp-interface is used if the GGSN
and the SGSN are located in different operator domains (i.e.
'other' PLMN). GTP protocol is defined for the Gn/Gp
interfaces (both GTP-C for the control plane and GTP-U for
the user plane).
Gb: Is the Base Station System (BSS) to SGSN interface, which is
used to carry information concerning packet data transmission
and layer-2 mobility management. The Gb-interface is based
on either on Frame Relay or IP.
Iu: Is the Radio Network System (RNS) to SGSN interface, which is
used to carry information concerning packet data transmission
and layer-2 mobility management. The user plane part of the
Iu-interface (actually the Iu-PS) is based on GTP-U. The
control plane part of the Iu-interface is based on Radio
Access Network Application Protocol (RANAP).
Gi: It is the interface between the GGSN and a PDN. The PDN may
be an operator external public or private packet data network
or an intra-operator packet data network.
Uu/Um: Are either 2G or 3G radio interfaces between a mobile
terminal and a respective radio access network.
The SGSN is responsible for the delivery of data packets from and to
the mobile hosts within its geographical service area when a direct
tunnel option is not used. If the direct tunnel is used, then the
Korhonen, et al. Expires January 12, 2012 [Page 11]
Internet-Draft IPv6 in 3GPP EPS July 2011
user plane goes directly between the RNS and the GGSN. The control
plane traffic always goes through the SGSN. For each mobile host
connected with the GPRS, at any given point of time, there is only
one SGSN.
3.2. PDP Context
A PDP context is an association between a mobile host represented by
one IPv4 address and/or one /64 IPv6 prefix and a PDN represented by
an APN. Each PDN can be accessed via a gateway (typically a GGSN or
PDN-GW). On the device/mobile host a PDP context is equivalent to a
network interface. A host may hence be attached to one or more
gateways via separate connections, i.e. PDP contexts. Each primary
PDP context has its own IPv4 address and/or one /64 IPv6 prefix
assigned to it by the PDN and anchored in the corresponding gateway.
Applications on the host use the appropriate network interface (PDP
context) for connectivity to a specific PDN. Figure 3 represents a
high level view of what a PDP context implies in 3GPP networks.
Y
| +---------+ .--.
|--+ __________________________ | APNx in | _( `.
| |O______PDPc1_______________)| GGSN / |----(Internet)
|MS| | PDN-GW | ( ` . ) )
|/ | +---------+ `--(___.-'
|UE| _______________________ +---------+ .--.
| |O______PDPc2____________)| APNy in | _(Priv`.
+--+ | GGSN / |-------(Network )
| PDN-GW | ( ` . ) )
+---------+ `--(___.-'
Figure 3: PDP contexts between the MS/UE and gateway
In the above figure there are two PDP contexts at the MS/UE (UE=User
Equipment in 3GPP parlance). The 'PDPc1' PDP context that is
connected to APNx provided Internet connectivity and the 'PDPc2' PDP
context provides connectivity to a private IP network via APNy (as an
example this network may include operator specific services such as
MMS (Multi media service). An application on the host such as a web
browser would use the PDP context that provides Internet connectivity
for accessing services on the Internet. An application such as MMS
would use APNy in the figure above because the service is provided
through the private network.
4. IP over 3GPP EPS
Korhonen, et al. Expires January 12, 2012 [Page 12]
Internet-Draft IPv6 in 3GPP EPS July 2011
4.1. Introduction to 3GPP EPS
In its most basic form, the EPS architecture consists of only two
nodes on the user plane, a base station and a core network Gateway
(GW). The basic EPS architecture is illustrated in Figure 4. The
Mobility Management Entity (MME) node performs control-plane
functionality and is separated from the node(s) that performs bearer-
plane functionality (GW), with a well-defined open interface between
them (S11). The optional interface S5 can be used to split the
Gateway (GW) into two separate nodes, the Serving Gateway (SGW) and
the PDN-GW. This allows independent scaling and growth of traffic
throughput and control signal processing. The functional split of
gateways also allows for operators to choose optimized topological
locations of nodes within the network and enables various deployment
models including the sharing of radio networks between different
operators.
+--------+
S1-MME +-------+ S11 | IP |
+----|----| MME |---|----+ |Services|
| | | | +--------+
| +-------+ | |SGi
+----+ LTE-Uu +-------+ S1-U +-------+ S5 +-------+
|MN |----|---|eNodeB |---|----------------| SGW |--|---|PDN-GW |
| |========|=======|====================|=======|======| |
+----+ +-------+DualStack EPS Bearer+-------+ +-------+
Figure 4: EPS Architecture for 3GPP Access
S5: It provides user plane tunnelling and tunnel management
between SGW and PDN-GW, using GTP or PMIPv6 as the network
based mobility management protocol.
S1-U: Provides user plane tunnelling and inter eNodeB path
switching during handover between eNodeB and SGW, using the
GTP-U protocol (GTP user plane).
S1-MME: Reference point for the control plane protocol between
eNodeB and MME.
SGi: It is the interface between the PDN-GW and the packet data
network. Packet data network may be an operator external
public or private packet data network or an intra operator
packet data network.
The eNodeB is a base station entity that supports the Long Term
Evolution (LTE) air interface and includes functions for radio
resource control, user plane ciphering, and other lower layer
Korhonen, et al. Expires January 12, 2012 [Page 13]
Internet-Draft IPv6 in 3GPP EPS July 2011
functions. MME is responsible for control plane functionalities,
including authentication, authorization, bearer management, layer-2
mobility, etc.
The SGW is the Mobility Anchor point for layer-2 mobility. For each
MN connected with the EPS, at any given point of time, there is only
one SGW.
4.2. PDN Connection
A PDN connection is an association between a mobile host represented
by one IPv4 address and/or one /64 IPv6 prefix, and a PDN represented
by an APN. The PDN connection is the EPC equivalent of the GPRS PDP
context. Each PDN can be accessed via a gateway (a PDN-GW). PDN is
responsible for the IP address/prefix allocation to the mobile host.
On the device/mobile host a PDN connection is equivalent to a network
interface. A host may hence be attached to one or more gateways via
separate connections, i.e. PDN connections. Each PDN connection has
its own IP address/prefix assigned to it by the PDN and anchored in
the corresponding gateway. Applications on the host use the
appropriate network interface (PDN connection) for connectivity.
4.3. EPS bearer model
The logical concept of a bearer has been defined to be an aggregate
of one or more IP flows related to one or more services. An EPS
bearer exists between the Mobile Node (MN i.e. a mobile host) and the
PDN-GW and is used to provide the same level of packet forwarding
treatment to the aggregated IP flows constituting the bearer.
Services with IP flows requiring a different packet forwarding
treatment would therefore require more than one EPS bearer. The
mobile host performs the binding of the uplink IP flows to the bearer
while the PDN-GW performs this function for the downlink packets.
In order to provide low latency for always on connectivity, a default
bearer will be provided at the time of startup and an IPv4 address
and/or IPv6 prefix gets assigned to the mobile host (this is
different from GPRS, where mobile hosts are not automatically
assigned with an IP address or prefix). This default bearer will be
allowed to carry all traffic which is not associated with a dedicated
bearer. Dedicated bearers are used to carry traffic for IP flows
that have been identified to require a specific packet forwarding
treatment. They may be established at the time of startup; for
example, in the case of services that require always-on connectivity
and better QoS than that provided by the default bearer. The default
bearer and the dedicated bearer(s) associated to it share the same IP
address(es)/prefix.
Korhonen, et al. Expires January 12, 2012 [Page 14]
Internet-Draft IPv6 in 3GPP EPS July 2011
An EPS bearer is referred to as a GBR bearer if dedicated network
resources related to a Guaranteed Bit Rate (GBR) value that is
associated with the EPS bearer are permanently allocated (e.g. by an
admission control function in the eNodeB) at bearer establishment/
modification. Otherwise, an EPS bearer is referred to as a non-GBR
bearer. The default bearer is always non-GBR, with the resources for
the IP flows not guaranteed at eNodeB, and with no admission control.
However, the dedicated bearer can be either GBR or non-GBR. A GBR
bearer has a Guaranteed Bit Rate (GBR) and Maximum Bit Rate (MBR)
while more than one non-GBR bearer belonging to the same UE shares an
Aggregate Maximum Bit Rate (AMBR). Non-GBR bearers can suffer packet
loss under congestion while GBR bearers are immune to such losses.
5. Address Management
5.1. IPv4 Address Configuration
Mobile host's IPv4 address configuration is always performed during
PDP context/EPS bearer setup procedures (on layer-2). DHCPv4-based
[RFC2131] address configuration is supported by the 3GPP
specifications, but is not used in wide scale. The mobile host must
always support layer-2 based address configuration, since DHCPv4 is
optional for both mobile hosts and networks.
5.2. IPv6 Address Configuration
IPv6 Stateless Address Autoconfiguration (SLAAC) as specified in
[RFC4862] is the only supported address configuration mechanism.
Stateful DHCPv6-based address configuration is not supported by 3GPP
specifications [RFC3315]. On the other hand, Stateless DHCPv6-
service to obtain other configuration information is supported
[RFC3736]. This implies that the M-bit must always be set to zero
and the O-bit may be set to one in the Router Advertisement (RA) sent
to the UE.
3GPP network allocates each default bearer a unique /64 prefix, and
uses layer-2 signaling to suggest user equipment an Interface
Identifier that is guaranteed not to conflict with gateway's
Interface Identifier. The UE must configure its link-local address
using this Interface Identifier. The UE is allowed to use any
Interface Identifier it wishes for the other addresses it configures.
There is no restriction, for example, of using Privacy Extension for
SLAAC [RFC4941] or other similar types of mechanisms.
In the 3GPP link model the /64 prefix assigned to the UE cannot be
used for on-link determination (because the L-bit in the Prefix
Information Option (PIO) in the RA must always be set to zero). If
Korhonen, et al. Expires January 12, 2012 [Page 15]
Internet-Draft IPv6 in 3GPP EPS July 2011
the advertised prefix is used for SLAAC then the A-bit in the PIO
must be set to one. The details of the 3GPP link-model and address
configuration is described in Section 11.2.1.3.2a of [TS.29061].
More specifically, the GGSN/PDN-GW guarantees that the /64 prefix is
unique for the mobile host. Therefore, there is no need to perform
any Duplicate Address Detection (DAD) on addresses the mobile host
creates (i.e., the 'DupAddrDetectTransmits' variable in the mobile
host could be zero). The GGSN/PDN-GW is not allowed to generate any
globally unique IPv6 addresses for itself using the /64 prefix
assigned to the mobile host in the RA.
The current 3GPP architecture limits number of prefixes in each
bearer to a single /64 prefix. If the mobile host finds more than
one prefix in the RA, it only considers the first one and silently
discards the others [TS.29061]. Therefore, multi-homing within a
single bearer is not possible. Renumbering without closing layer-2
connection is also not possible. The lifetime of /64 prefix is bound
to lifetime of layer-2 connection even if the advertised prefix
lifetime is longer than the layer-2 connection lifetime.
5.3. Prefix Delegation
IPv6 prefix delegation is a part of Release-10 and is not covered by
any earlier release. However, the /64 prefix allocated for each
default bearer (and to the user equipment) may be shared to local
area network by user equipment implementing Neighbor Discovery proxy
(ND proxy) [RFC4389] functionality.
Release-10 prefix delegation uses the DHCPv6-based prefix delegation
[RFC3633]. The model defined for Release-10 requires aggregatable
prefixes, which means the /64 prefix allocated for the default bearer
(and to the user equipment) must be part of the shorter delegated
prefix. DHCPv6 prefix delegation has an explicit limitation
described in Section 12.1 of [RFC3633] that a prefix delegated to a
requesting router cannot be used by the delegating router (i.e., the
PDN-GW in this case). This implies the shorter 'delegated prefix'
cannot be given to the requesting router (i.e. the user equipment) as
such but has to be delivered by the delegating router (i.e. the
PDN-GW) in such a way the /64 prefix allocated to the default bearer
is not part of the 'delegated prefix'. IETF is working on a solution
for DHCPv6-based prefix delegation to exclude a specific prefix from
the 'delegated prefix' [I-D.ietf-dhc-pd-exclude].
5.4. IPv6 Neighbor Discovery Considerations
3GPP link between the UE and the next hop router (e.g. GGSN)
resemble a point to point (p2p) link, which has no link-layer
addresses [RFC3316] and this has not changed from 2G/3G GPRS to EPS.
Korhonen, et al. Expires January 12, 2012 [Page 16]
Internet-Draft IPv6 in 3GPP EPS July 2011
The UE IP stack has to take this into consideration. When the 3GPP
PDP Context appears as a PPP interface/link to the UE, the IP stack
is usually prepared to handle Neighbor Discovery protocol and the
related Neighbor Cache state machine transitions in an appropriate
way, even though Neighbor Discovery protocol messages contain no link
layer address information. However, some operating systems discard
Router Advertisements on their PPP interface/link as a default
setting. This causes the SLAAC to fail when the 3GPP PDP Context
gets established, thus stalling all IPv6 traffic.
Currently several operating systems and their network drivers can
make the 3GPP PDP Context to appear as an IEEE802 interface/link to
the IP stack. This has few known issues, especially when the IP
stack is made to believe the underlying link has link-layer
addresses. First, the Neighbor Advertisement sent by a GGSN as a
response to an address resolution triggered Neighbor Solicitation may
not contain a Target Link-Layer address option (as suggested in
[RFC4861] Section 4.4). Then it is possible that the address
resolution never completes when the UE tries to resolve the link-
layer address of the GGSN, thus stalling all IPv6 traffic.
Second, the GGSN may simply discard all address resolution triggered
Neighbor Solicitation messages (as hinted in [RFC3316] Section 2.4.1
that address resolution and next-hop determination are not needed).
As a result the address resolution never completes when the UE tries
to resolve the link-layer address of the GGSN, thus stalling all IPv6
traffic.
6. 3GPP Dual-Stack Approach to IPv6
6.1. 3GPP Networks Prior to Release-8
3GPP standards prior to Release-8 provide IPv6 access for cellular
devices with PDP contexts of type IPv6 [TS.23060]. For dual-stack
access, a PDP context of type IPv6 is established in parallel to the
PDP context of type IPv4, as shown in Figure 5 and Figure 6. For
IPv4-only service, connections are created over the PDP context of
type IPv4 and for IPv6-only service connections are created over the
PDP context of type IPv6. The two PDP contexts of different type may
use the same APN (and the gateway), however, this aspect is not
explicitly defined in standards. Therefore, cellular device and
gateway implementations from different vendors may have varying
support for this functionality.
Korhonen, et al. Expires January 12, 2012 [Page 17]
Internet-Draft IPv6 in 3GPP EPS July 2011
Y .--.
| _(IPv4`.
|---+ +---+ +---+ ( PDN )
| D |~~~~~~~//-----| |====| |====( ` . ) )
| S | IPv4 context | S | | G | `--(___.-'
| | | G | | G | .--.
| M | | S | | S | _(IPv6`.
| N | IPv6 context | N | | N | ( PDN )
|///|~~~~~~~//-----| |====|(s)|====( ` . ) )
+---+ +---+ +---+ `--(___.-'
Figure 5: A dual-stack mobile host connecting to both IPv4 and IPv6
Internet using parallel IPv4-only and IPv6-only PDP contexts
Y
|
|---+ +---+ +---+
| D |~~~~~~~//-----| |====| | .--.
| S | IPv4 context | S | | G | _( DS `.
| | | G | | G | ( PDN )
| M | | S | | S |====( ` . ) )
| N | IPv6 context | N | | N | `--(___.-'
|///|~~~~~~~//-----| |====| |
+---+ +---+ +---+
Figure 6: A dual-stack mobile host connecting to dual-stack Internet
using parallel IPv4-only and IPv6-only PDP contexts
The approach of having parallel IPv4 and IPv6 type of PDP contexts
open is not optimal, because two PDP contexts require double the
signaling and consume more network resources than a single PDP
context. In the figure above the IPv4 and IPv6 PDP contexts are
attached to the same GGSN. While this is possible, the dual-stack
(DS) MS may be attached to different GGSNs in the scenario where one
GGSN supports IPv4 PDN connectivity while another GGSN provides IPv6
PDN connectivity.
6.2. 3GPP Release-8 and -9 Networks
Since 3GPP Release-8, the powerful concept of a dual-stack type of
PDN connection and EPS bearer have been introduced [TS.23401]. This
enables parallel use of both IPv4 and IPv6 on a single bearer
(IPv4v6), as illustrated in Figure 7, and makes dual stack simpler
than in earlier 3GPP releases. As of Release-9, GPRS network nodes
also support dual-stack type (IPv4v6) PDP contexts.
Korhonen, et al. Expires January 12, 2012 [Page 18]
Internet-Draft IPv6 in 3GPP EPS July 2011
Y
|
|---+ +---+ +---+
| D | | | | P | .--.
| S | | | | D | _( DS `.
| | IPv4v6 (DS) | S | | N | ( PDN )
| M |~~~~~~~//-----| G |====| - |====( ` . ) )
| N | bearer | W | | G | `--(___.-'
|///| | | | W |
+---+ +---+ +---+
Figure 7: A dual-stack mobile host connecting to dual-stack Internet
using a single IPv4v6 type PDN connection
The following is a description of the various PDP contexts/PDN bearer
types that are specified by 3GPP:
1. For 2G/3G access to GPRS core (SGSN/GGSN) pre-Release-9 there are
two IP PDP Types, IPv4 and IPv6. Two PDP contexts are needed to
get dual stack connectivity.
2. For 2G/3G access to GPRS core (SGSN/GGSN) from Release-9 there
are three IP PDP Types, IPv4, IPv6 and IPv4v6. Minimum one PDP
context is needed to get dual stack connectivity.
3. For 2G/3G access to EPC core (PDN-GW via S4-SGSN) from Release-8
there are three IP PDP Types, IPv4, IPv6 and IPv4v6 which gets
mapped to PDN Connection type. Minimum one PDP Context is needed
to get dual stack connectivity.
4. For LTE (E-UTRAN) access to EPC core from Release-8 there are
three IP PDN Types, IPv4, IPv6 and IPv4v6. Minimum one PDN
Connection is needed to get dual stack connectivity.
6.3. PDN Connection Establishment Process
The PDN connection establishment process is specified in detail in
3GPP specifications. Figure 8 illustrates the high level process and
signaling involved in the establishment of a PDN connection.
Korhonen, et al. Expires January 12, 2012 [Page 19]
Internet-Draft IPv6 in 3GPP EPS July 2011
UE eNb/ MME SGW PDN-GW HSS/
| BS | | | AAA
| | | | | |
|---------->|(1) | | | |
| |---------->|(1) | | |
| | | | | |
|/---------------------------------------------------------\|
| Authentication and Authorization |(2)
|\---------------------------------------------------------/|
| | | | | |
| | |---------->|(3) | |
| | | |---------->|(3) |
| | | | | |
| | | |<----------|(4) |
| | |<----------|(4) | |
| |<----------|(5) | | |
|/---------\| | | | |
| RB setup |(6) | | | |
|\---------/| | | | |
| |---------->|(7) | | |
|---------->|(8) | | | |
| |---------->|(9) | | |
| | | | | |
|============= Uplink Data =========>==========>|(10) |
| | | | | |
| | |---------->|(11) | |
| | | | | |
| | |<----------|(12) | |
| | | | | |
|<============ Downlink Data =======<===========|(13) |
| | | | | |
Figure 8: Simplified PDN connection setup procedure in Release-8
1. The UE (i.e the MS) requires a data connection and hence decides
to establish a PDN connection with a PDN-GW. The UE sends an
"Attach Request" (layer-2) to the BS. The BS forwards this
attach request to the MME.
2. Authentication of the UE with the AAA server/HSS follows. If
the UE is authorized for establishing a data connection, the
following steps continue
3. The MME sends a "Create Session Request" message to the
Serving-GW. The SGW forwards the create session request to the
PDN-GW. The SGW knows the address of the PDN-GW to forward the
create session request to as a result of this information having
been obtained by the MME during the authentication/authorization
Korhonen, et al. Expires January 12, 2012 [Page 20]
Internet-Draft IPv6 in 3GPP EPS July 2011
phase.
The UE IPv4 address and/or IPv6 prefix get assigned during this
step. If a subscribed IPv4 address and/or IPv6 prefix is
statically allocated for the UE for this APN, then the MME
already passes the address information to the SGW and eventually
to the PDN-GW in the "Create Session Request" message.
Otherwise, the PDN-GW manages the address assignment to the UE
(there is another variation to this where IPv4 address
allocation is delayed until the UE initiates a DHCPv4 exchange
but this is not discussed here).
4. The PDN-GW creates a PDN connection for the UE and sends "Create
Session Response" message to the SGW from which the session
request message was received from. The SGW forwards the
response to the corresponding MME which originated the request.
5. The MME sends the "Attach Accept/Initial Context Setup request"
message to the eNodeB/BS.
6. The radio bearer between the UE and the eNb is reconfigured
based on the parameters received from the MME. (See note 1
below)
7. The eNb sends "Initial Context Response" message to the MME.
8. The UE sends a "Direct Transfer" message to the eNodeB which
includes the Attach complete signal.
9. The eNodeB forwards the Attach complete message to the MME.
10. The UE can now start sending uplink packets to the PDN GW.
11. The MME sends a "Modify Bearer Request" message to the SGW.
12. The SGW responds with a "Modify Bearer Response" message. At
this time the downlink connection is also ready.
13. The UE can now start receiving downlink packets, including
possible SLAAC related IPv6 packets.
The type of PDN connection established between the UE and the PDN-GW
can be any of the types described in the previous section. The dual-
stack (DS) PDN connection, i.e the one which supports both IPv4 and
IPv6 packets is the default one that will be established if no
specific PDN connection type is specified by the UE in Release-8
networks.
Korhonen, et al. Expires January 12, 2012 [Page 21]
Internet-Draft IPv6 in 3GPP EPS July 2011
Note 1: The UE receives the PDN Address Information Element
[TS.24301] at the end of radio bearer setup messaging. This
Information Element contains only the Interface Identifier of the
IPv6 address. In a case of GPRS the PDP Address Information
Element [TS.24008] would contain a complete IPv6 address.
However, the UE must ignore the IPv6 prefix if it receives one in
the message (see Section 11.2.1.3.2a of [TS.29061]).
6.4. Mobility of 3GPP IPv4v6 Type of Bearers
3GPP discussed at length various approaches to support mobility
between a Release-8 LTE network and a pre-Release-9 2G/3G network
without a S4-SGSN for the new dual-stack type of bearers. The chosen
approach for mobility is as follows, in short: if a mobile is allowed
for doing handovers between a Release-8 LTE network and a pre-
Release-9 2G/3G network without a S4-SGSN while having open PDN
connections, only single stack bearers are used. Essentially this
means following deployment options:
1. If a network knows a mobile may do handovers between a Release-8
LTE network and a pre-Release-9 2G/3G network without a S4-SGSN,
then the network is configured to provide only single stack
bearers, even if the mobile host requests dual-stack bearers.
2. If the network knows the mobile does handovers only between a
Release-8 LTE network and a Release-9 2G/3G network or a pre-
Release-9 network with a S4-SGSN, then the network is configured
to provide the mobile with dual-stack bearers on request. The
same also applies for LTE-only deployments.
When a network operator and their roaming partners have upgraded
their networks to Release-8, it is possible to use the new IPv4v6
dual-stack type of bearers. A Release-8 mobile device always
requests for a dual-stack bearer, but accepts what is assigned by the
network.
7. Dual-Stack Approach to IPv6 Transition in 3GPP Networks
3GPP networks can natively transport IPv4 and IPv6 packets between
the mobile station/UE and the gateway (GGSN or PDN-GW) as a result of
establishing either a dual-stack PDP context or parallel IPv4 and
IPv6 PDP contexts.
Current deployments of 3GPP networks primarily support IPv4-only.
These networks can be upgraded to also support IPv6 PDP contexts. By
doing so devices and applications that are IPv6 capable can start
utilizing the IPv6 connectivity. This will also ensure that legacy
Korhonen, et al. Expires January 12, 2012 [Page 22]
Internet-Draft IPv6 in 3GPP EPS July 2011
devices and applications continue to work with no impact. As newer
devices start using IPv6 connectivity, the demand for actively used
IPv4 connections is expected to slowly decrease, helping operators
with a transition to IPv6. With a dual-stack approach, there is
always the potential to fallback to IPv4. A device which may be
roaming in a network wherein IPv6 is not supported by the visited
network could fall back to using IPv4 PDP contexts and hence the end
user would at least get some connectivity. Unfortunately, dual-stack
approach as such does not lower the number of used IPv4 addresses.
Every dual-stack bearer still needs to be given an IPv4 address,
private or public. This is a major concern with dual-stack bearers
concerning IPv6 transition. However, if the majority of active IP
communication has moved over to IPv6, then in case of NAT44 [RFC1918]
IPv4 connections the number of active IPv4 connections can still be
expected to gradually decrease and thus giving some level of relief
regarding NAT44 function scalability.
As the networks evolve to support Release-8 EPS architecture and the
dual-stack PDP contexts, newer devices will be able to leverage such
capability and have a single bearer which supports both IPv4 and
IPv6. Since IPv4 and IPv6 packets are carried as payload within GTP
between the MS and the gateway (GGSN/PDN-GW) the transport network
capability in terms of whether it supports IPv4 or IPv6 on the
interfaces between the eNodeB and SGW or, SGW and PDN-GW is
immaterial.
8. Deployment issues
8.1. Overlapping IPv4 Addresses
Given the shortage of globally routable public IPv4 addresses,
operators tend to assign private IPv4 addresses [RFC1918] to hosts
when they establish an IPv4-only PDP context or an IPv4v6 type PDN
context. About 16 million hosts can be assigned a private IPv4
address that is unique within a domain. However, in case of many
operators the number of subscribers is greater than 16 million. The
issue can be dealt with by assigning overlapping RFC 1918 IPv4
addresses to hosts. As a result the IPv4 address assigned to a host
within the context of a single operator realm would no longer be
unique. This has the obvious and known issues of NATed IP connection
in the Internet. Direct host to host connectivity becomes
complicated, unless the hosts are within the same private address
range pool and/or anchored to the same gateway, referrals using IP
addresses will have issues and so forth. These are generic issues
and not only a concern of the EPS. However, 3GPP as such does not
have any mandatory language concerning NAT44 functionality in EPC.
Obvious deployment choices apply also to EPC:
Korhonen, et al. Expires January 12, 2012 [Page 23]
Internet-Draft IPv6 in 3GPP EPS July 2011
1. Very large network deployments are partitioned, for example,
based on a geographical areas. This partitioning allows for
overlapping IPv4 addresses ranges to be assigned to hosts that
are in different areas. Each area has its own pool of gateways
that are dedicated for a certain overlapping IPv4 address range
(referred here later as a zone). Standard NAT44 functionality
allows for communication from the [RFC1918] private zone to the
Internet. Communication between zones require special
arrangement, such as using intermediate gateways (e.g. Back to
Back User Agent (B2BUA) in case of SIP).
2. A mobile host/device attaches to a gateway as part of the attach
process. The number of hosts that a gateway supports is in the
order of 1 to 10 million. Hence all the hosts assigned to a
single gateway can be assigned private IPv4 addresses. Operators
with large subscriber bases have multiple gateways and hence the
same [RFC1918] IPv4 address space can be reused across gateways.
The IPv4 address assigned to a host is unique within the scope of
a single gateway.
3. New services requiring direct connectivity between hosts should
be build on IPv6. Possible existing IPv4-only services and
applications requiring direct connectivity can be ported to IPv6.
8.2. IPv6 for transport
The various reference points of the 3GPP architecture such as S1-U,
S5 and S8 are based on either GTP or PMIPv6. The underlying
transport for these reference points can be IPv4 or IPv6. GTP has
been able to operate over IPv6 transport (optionally) since R99 and
PMIPv6 has supported IPv6 transport starting from its introduction in
Release-8. The user plane traffic between the mobile host and the
gateway can use either IPv4 or IPv6. These packets are essentially
treated as payload by GTP/PMIPv6 and transported accordingly with no
real attention paid to the information (at least from a routing
perspective) contained in the IPv4 or IPv6 headers. The transport
links between the eNodeB and the SGW, and the link between the SGW
and PDN-GW can be migrated to IPv6 without any direct implications to
the architecture.
Currently, the inter-operator (for 3GPP technology) roaming networks
are all IPv4-only (see Inter-PLMN Backbone Guidelines [GSMA.IR.34]).
Eventually these roaming networks will also get migrated to IPv6, if
there is a business reason for that. The migration period can be
prolonged considerably because the 3GPP protocols always tunnel user
plane traffic in the core network and as described earlier the
transport network IP version is not in any way tied to user plane IP
version. Furthermore, the design of the inter-operator roaming
Korhonen, et al. Expires January 12, 2012 [Page 24]
Internet-Draft IPv6 in 3GPP EPS July 2011
networks is such that the user plane and transport network IP
addressing is completely separated from each other. The inter-
operator roaming network itself is also completely separated from the
Internet. Only those core network nodes that must be connected to
the inter-operator roaming networks are actually visible there, and
be able to send and receive (tunneled) traffic within the inter-
operator roaming networks. Obviously, in order the roaming to work
properly, the operators have to agree on supported protocol versions
so that the visited network does not, for example, unnecessarily drop
user plane IPv6 traffic.
8.3. Operational Aspects of Running Dual-Stack Networks
Operating dual-stack networks does imply cost and complexity to a
certain extent. However these factors are mitigated by the assurance
that legacy devices and services are unaffected and there is always a
fallback to IPv4 in case of issues with the IPv6 deployment or
network elements. The model also enables operators to develop
operational experience and expertise in an incremental manner.
Running dual-stack networks requires the management of multiple IP
address spaces. Tracking of hosts needs to be expanded since it can
be identified by either an IPv4 address or IPv6 prefix. Network
elements will also need to be dual-stack capable in order to support
the dual-stack deployment model.
Deployment and migration cases described in Section 6.1 for providing
dual-stack like capability may mean doubled resource usage in
operator's network. This is a major concern against providing dual-
stack like connectivity using techniques discussed in Section 6.1.
Also handovers between networks with different capabilities in terms
of networks being dual-stack like service capable or not, may turn
out hard to comprehend for users and for application/services to cope
with. These facts may add other than just technical concerns for
operators when planning to roll out dual-stack service offerings.
8.4. Operational Aspects of Running a Network with IPv6-only Bearers
It is possible to allocate IPv6-only type bearers to mobile hosts in
3GPP networks. IPv6-only bearer type has been part of the 3GPP
specification since the beginning. In 3GPP Release-8 (and later) it
was defined that a dual-stack mobile host (or when the radio
equipment has no knowledge of the host IP stack capabilities) must
first attempt to establish a dual-stack bearer and then possibly fall
back to single IP version bearer. A Release-8 (or later) mobile host
with IPv6-only stack can directly attempt to establish an IPv6-only
bearer. The IPv6-only behaviour is up to a subscription provisioning
or a PDN-GW configuration, and the fallback scenarios do not
Korhonen, et al. Expires January 12, 2012 [Page 25]
Internet-Draft IPv6 in 3GPP EPS July 2011
necessarily cause additional signaling.
Although the bullets below introduce IPv6 to IPv4 address translation
and specifically discuss NAT64 technology [RFC6144], the current 3GPP
Release-8 architecture does not describe the use of address
translation or NAT64. It is up to a specific deployment whether
address translation is part of the network or not. Some operational
aspects to consider for running a network with IPv6-only bearers:
o The mobile hosts must have an IPv6 capable stack and a radio
interface capable of establishing an IPv6 PDP context or PDN
connection.
o The GGSN/PDN-GW must be IPv6 capable in order to support IPv6
bearers. Furthermore, the SGSN/MME must allow the creation of PDP
Type or PDN Type of IPv6.
o Many of the common applications are IP version agnostic and hence
would work using an IPv6 bearer. However, applications that are
IPv4 specific would not work.
o Inter-operator roaming is another aspect which causes issues, at
least during the ramp up phase of the IPv6 deployment. If the
visited network to which outbound roamers attach to does not
support PDP/PDN Type IPv6, then there needs to be a fallback
option. The fallback option in this specific case is mostly up to
the mobile host to implement. Several cases are discussed in the
following sections.
o If and when a mobile host using IPv6-only bearer needs to access
to IPv4 Internet/network, a translation of some type from IPv6 to
IPv4 has to be deployed in the network. NAT64 (and DNS64) is one
solution that can be used for this purpose and works for a certain
set of protocols (read TCP, UDP and ICMP, and when applications
actually use DNS for resolving name to IP addresses).
8.5. Restricting Outbound IPv6 Roaming
Roaming was briefly touched upon in Sections 8.2 and 8.4. While
there is interest in offering roaming service for IPv6 enabled mobile
hosts and subscriptions, not all visited networks are prepared for
IPv6 outbound roamers. There are basically two issues. First, the
visited network SGSN does not support the IPv6 PDP Context or IPv4v6
PDP Context types. These should mostly concern pre-Release-9 2G/3G
networks without S4-SGSN but there is no definitive rule as the
deployed feature sets vary depending on implementations and licenses.
Second, the visited network might not be commercially ready for IPv6
outbound roamers, while everything might work technically at the user
Korhonen, et al. Expires January 12, 2012 [Page 26]
Internet-Draft IPv6 in 3GPP EPS July 2011
plane level. This would lead to "revenue leakage" especially from
the visited operator point of view (note that the use of visited
network GGSN/PDN-GW does not really exist in real deployments today).
Therefore, it might be in the interest of operators to prohibit
roaming selectively within specific visited networks.
Unfortunately, it is not mandatory to implement/deploy 3GPP standards
based solution to selectively prohibit IPv6 roaming without also
prohibiting other packet services (such as IPv4 roaming). However,
there are few possibilities how this can be done in real deployments.
The examples given below are either optional and/or vendor specific
features to the 3GPP EPC:
o Using Policy and Charging Control (PCC) [TS.23203] functionality
and its rules to fail, for example, the bearer authorization when
a desired criteria is met. In this case that would be PDN/PDP
Type IPv6/IPv4v6 and a specific visited network. The rules can be
provisioned either in the home network or locally in the visited
network.
o Some Home Location Register (HLR) and Home Subscriber Server (HSS)
subscriber databases allow prohibiting roaming in a specific
(visited) network for a specified PDN/PDP Type.
The obvious problems are that these solutions are not mandatory, are
not unified across networks, and therefore also lack well-specified
fall back mechanism from the mobile host point of view.
8.6. Inter-RAT Handovers and IP Versions
It is obvious that operators start incrementally deploy EPS along
with the existing UTRAN/GERAN, handovers between different radio
technologies (inter-RAT handovers) become inevitable. In case of
inter-RAT handovers 3GPP supports the following IP addressing
scenarios:
o E-UTRAN IPv4v6 bearer has to map one to one to UTRAN/GERAN IPv4v6
bearer.
o E-UTRAN IPv6 bearer has to map one to one to UTRAN/GERAN IPv6
bearer.
o E-UTRAN IPv4 bearer has to map one to one to UTRAN/GERAN IPv4
bearer.
Other types of configurations are considered network planning
mistakes. What the above rules essentially imply is that the network
migration has to be planned and subscriptions provisioned based on
Korhonen, et al. Expires January 12, 2012 [Page 27]
Internet-Draft IPv6 in 3GPP EPS July 2011
the lowest common nominator, if inter-RAT handovers are desired. For
example, if some part of the UTRAN network cannot serve anything but
IPv4 bearers, then the E-UTRAN is also forced to provide only IPv4
bearers. Various combinations of subscriber provisioning regarding
IP versions are discussed further in Section 8.7.
8.7. Provisioning of IPv6 Subscribers and Various Combinations During
Initial Network Attachment
Subscribers' provisioned PDP/PDN Types have multiple configurations.
The supported PDP/PDN Type is provisioned per each APN for every
subscriber. The following PDN Types are possible in the HSS for a
Release-8 subscription [TS.23401]:
o IPv4v6 PDN Type (note that IPv4v6 PDP Type does not exist in a HLR
and Mobile Applicatio Part (MAP) [TS.29002] signaling prior
Release-9).
o IPv6-only PDN Type
o IPv4-only PDN Type.
o IPv4_or_IPv6 PDN Type (note that IPv4_or_IPv6 PDP Type does not
exist in a HLR or MAP signaling. However, a HLR may have multiple
APN configurations of different PDN Types, which effectively
achieves the same functionality).
A Release-8 dual-stack mobile host must always attempt to establish a
PDP/PDN Type IPv4v6 bearer. The same also applies when the modem
part of the mobile host does not have exact knowledge whether the
host operating system IP stack is a dual-stack capable or not. A
mobile host that is IPv6-only capable must attempt to establish a
PDP/PDN Type IPv6 bearer. Last, a mobile host that is IPv4-only
capable must attempt to establish a PDN/PDP Type IPv4 bearer.
In a case the PDP/PDN Type requested by a mobile host does not match
what has been provisioned for the subscriber in the HSS (or HLR), the
mobile host possibly falls back to a different PDP/PDN Type. The
network (i.e. the MME or the S4-SGSN) is able to inform the mobile
host during the network attachment signaling why it did not get the
requested PDP/PDN Type. These response/cause codes are documented in
[TS.24008] for requested PDP Types and [TS.24301] for requested PDN
Types:
o (E)SM cause #50 "PDN/PDP type IPv4-only allowed".
o (E)SM cause #51 "PDN/PDP type IPv6-only allowed".
Korhonen, et al. Expires January 12, 2012 [Page 28]
Internet-Draft IPv6 in 3GPP EPS July 2011
o (E)SM cause #52 "single address bearers only allowed".
The above response/cause codes apply to Release-8 and onwards. In
pre-Release-8 networks used response/cause codes vary depending on
the vendor, unfortunately.
Possible fall back cases when the network deploys MMEs and/or S4-
SGSNs include (as documented in [TS.23401]):
o Requested and provisioned PDP/PDN Types match => requested.
o Requested IPv4v6 and provisioned IPv6 => IPv6 and a mobile host
receives indication that IPv6-only bearer is allowed.
o Requested IPv4v6 and provisioned IPv4 => IPv4 and the mobile host
receives indication that IPv4-only bearer is allowed.
o Requested IPv4v6 and provisioned IPv4_or_IPv6 => IPv4 or IPv6 is
selected by the MME/S4-SGSN based on an unspecified criteria. The
mobile host may then attempt to establish, based on the mobile
host implementation, a parallel bearer of a different PDP/PDN
Type.
o Other combinations cause the bearer establishment to fail.
In addition to PDP/PDN Types provisioned in the HSS, it is also
possible for a PDN-GW (and a MME/S4-SGSN) to affect the final
selected PDP/PDN Type:
o Requested IPv4v6 and configured IPv4 or IPv6 in the PDN-GW => IPv4
or IPv6. If the MME operator had included the "Dual Address
Bearer Flag" into the bearer establishment signaling, then the
mobile host receives an indication that IPv6-only or IPv4-only
bearer is allowed.
o Requested IPv4v6 and configured IPv4 or IPv6 in the PDN-GW => IPv4
or IPv6. If the MME operator had not included the "Dual Address
Bearer Flag" into the bearer establishment signaling, then the
mobile host may attempt to establish, based on the mobile host
implementation, a parallel bearer of different PDP/PDN Type.
A SGSN that does not understand the requested PDP Type is supposed to
handle the requested PDP Type as IPv4. If for some reason a MME does
not understand the requested PDN Type, then the PDN Type is handled
as IPv6.
Korhonen, et al. Expires January 12, 2012 [Page 29]
Internet-Draft IPv6 in 3GPP EPS July 2011
9. IANA Considerations
This document has no requests to IANA.
10. Security Considerations
This document does not introduce any security related concerns.
11. Summary and Conclusion
The 3GPP network architecture and specifications enable the
establishment of IPv4 and IPv6 connections through the use of
appropriate PDP context types. The current generation of deployed
networks can support dual-stack connectivity if the packet core
network elements such as the SGSN and GGSN have the capability. With
Release-8, 3GPP has specified a more optimal PDP context type which
enables the transport of IPv4 and IPv6 packets within a single PDP
context between the mobile station and the gateway.
As devices and applications are upgraded to support IPv6 they can
start leveraging the IPv6 connectivity provided by the networks while
maintaining the fall back to IPv4 capability. Enabling IPv6
connectivity in the 3GPP networks by itself will provide some degree
of relief to the IPv4 address space as many of the applications and
services can start to work over IPv6. However without comprehensive
testing of different applications and solutions that exist today and
are widely used, for their ability to operate over IPv6 PDN
connections, an IPv6-only access would cause disruptions.
12. Acknowledgements
The authors thank Shabnam Sultana, Sri Gundavelli, Hui Deng, and
Zhenqiang Li, Mikael Abrahamsson, James Woodyatt, Cameron Byrne, Ales
Vizdal and Frank Brockners for their reviews and comments on this
document.
13. Informative References
[GSMA.IR.34]
GSMA, "Inter-PLMN Backbone Guidelines", GSMA
PRD IR.34.4.9, March 2010.
[I-D.ietf-dhc-pd-exclude]
Korhonen, J., Savolainen, T., Krishnan, S., and O. Troan,
Korhonen, et al. Expires January 12, 2012 [Page 30]
Internet-Draft IPv6 in 3GPP EPS July 2011
"Prefix Exclude Option for DHCPv6-based Prefix
Delegation", draft-ietf-dhc-pd-exclude-02 (work in
progress), June 2011.
[RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and
E. Lear, "Address Allocation for Private Internets",
BCP 5, RFC 1918, February 1996.
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol",
RFC 2131, March 1997.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3316] Arkko, J., Kuijpers, G., Soliman, H., Loughney, J., and J.
Wiljakka, "Internet Protocol Version 6 (IPv6) for Some
Second and Third Generation Cellular Hosts", RFC 3316,
April 2003.
[RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic
Host Configuration Protocol (DHCP) version 6", RFC 3633,
December 2003.
[RFC3736] Droms, R., "Stateless Dynamic Host Configuration Protocol
(DHCP) Service for IPv6", RFC 3736, April 2004.
[RFC4389] Thaler, D., Talwar, M., and C. Patel, "Neighbor Discovery
Proxies (ND Proxy)", RFC 4389, April 2006.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.
[RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy
Extensions for Stateless Address Autoconfiguration in
IPv6", RFC 4941, September 2007.
[RFC5213] Gundavelli, S., Leung, K., Devarapalli, V., Chowdhury, K.,
and B. Patil, "Proxy Mobile IPv6", RFC 5213, August 2008.
[RFC6144] Baker, F., Li, X., Bao, C., and K. Yin, "Framework for
IPv4/IPv6 Translation", RFC 6144, April 2011.
[TR.23975]
Korhonen, et al. Expires January 12, 2012 [Page 31]
Internet-Draft IPv6 in 3GPP EPS July 2011
3GPP, "IPv6 Migration Guidelines", 3GPP TR 23.975 1.1.1,
June 2010.
[TS.23060]
3GPP, "General Packet Radio Service (GPRS); Service
description; Stage 2", 3GPP TS 23.060 8.8.0, March 2010.
[TS.23203]
3GPP, "Policy and charging control architecture (PCC)",
3GPP TS 23.203 8.11.0, September 2010.
[TS.23401]
3GPP, "General Packet Radio Service (GPRS) enhancements
for Evolved Universal Terrestrial Radio Access Network
(E-UTRAN) access", 3GPP TS 23.401 10.4.0, June 2011.
[TS.24008]
3GPP, "Mobile radio interface Layer 3 specification", 3GPP
TS 24.008 8.12.0, December 2010.
[TS.24301]
3GPP, "Non-Access-Stratum (NAS) protocol for Evolved
Packet System (EPS)", 3GPP TS 24.301 8.8.0, December 2010.
[TS.29002]
3GPP, "Mobile Application Part (MAP) specification", 3GPP
TS 29.002 9.5.0, June 2011.
[TS.29060]
3GPP, "General Packet Radio Service (GPRS); GPRS
Tunnelling Protocol (GTP) across the Gn and Gp interface",
3GPP TS 29.274 8.8.0, April 2010.
[TS.29061]
3GPP, "Interworking between the Public Land Mobile Network
(PLMN) supporting packet based services and Packet Data
Networks (PDN)", 3GPP TS 29.061 8.5.0, April 2010.
[TS.29274]
3GPP, "3GPP Evolved Packet System (EPS); Evolved General
Packet Radio Service (GPRS) Tunnelling Protocol for
Control plane (GTPv2-C)", 3GPP TS 29.060 8.11.0,
December 2010.
Korhonen, et al. Expires January 12, 2012 [Page 32]
Internet-Draft IPv6 in 3GPP EPS July 2011
Authors' Addresses
Jouni Korhonen (editor)
Nokia Siemens Networks
Linnoitustie 6
FI-02600 Espoo
FINLAND
Email: jouni.nospam@gmail.com
Jonne Soininen
Renesas Mobile
Porkkalankatu 24
FI-00180 Helsinki
FINLAND
Email: jonne.soininen@renesasmobile.com
Basavaraj Patil
Nokia
6021 Connection drive
Irving, TX 75039
USA
Email: basavaraj.patil@nokia.com
Teemu Savolainen
Nokia
Hermiankatu 12 D
FI-33720 Tampere
FINLAND
Email: teemu.savolainen@nokia.com
Gabor Bajko
Nokia
323 Fairchild drive 6
Mountain view, CA 94043
USA
Email: gabor.bajko@nokia.com
Korhonen, et al. Expires January 12, 2012 [Page 33]
Internet-Draft IPv6 in 3GPP EPS July 2011
Kaisu Iisakkila
Renesas Mobile
Porkkalankatu 24
FI-00180 Helsinki
FINLAND
Email: kaisu.iisakkila@renesasmobile.com
Korhonen, et al. Expires January 12, 2012 [Page 34]