MPLS Working Group K. Kompella, Ed.
Internet-Draft Juniper Networks
Intended status: Standards Track S. Bryant
Expires: 15 July 2023 University of Surrey 5GIC
M. Bocci
Nokia
G. Mirsky
Ericsson
L. Andersson
Bronze Dragon Consulting
11 January 2023
IANA Registry for the First Nibble Following a Label Stack
draft-kbbma-mpls-1stnibble-04
Abstract
The goal of this memo is to create a new IANA registry (called the
MPLS First Nibble registry) for the first nibble (4-bit field)
immediately following an MPLS label stack. The memo offers a
rationale for such a registry, describes how the registry should be
managed, and provides some initial entries. Furthermore, this memo
sets out some documentation requirements for registering new values.
Finally, it provides some recommendations that makes processing MPLS
packets easier and more robust.
There is an important caveat on the use of this registry versus the
IP version number registry.
This memo, if published, would update [RFC4928] and [RFC8469].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 15 July 2023.
Kompella, et al. Expires 15 July 2023 [Page 1]
Internet-Draft 1st nibble January 2023
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Conventions and Definitions . . . . . . . . . . . . . . . 3
2. Rationale . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1. Why Look at the First Nibble . . . . . . . . . . . . . . 5
2.1.1. Load Balancing . . . . . . . . . . . . . . . . . . . 6
2.1.2. Requirement . . . . . . . . . . . . . . . . . . . . . 7
2.1.3. Recommendation . . . . . . . . . . . . . . . . . . . 8
2.1.4. Parsing the Post-stack Header . . . . . . . . . . . . 9
2.2. Why Create a Registry . . . . . . . . . . . . . . . . . . 9
2.3. Caveat . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
3.1. MPLS First Nibble Registry . . . . . . . . . . . . . . . 10
3.1.1. Allocation Policy . . . . . . . . . . . . . . . . . . 10
4. References . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1. Normative References . . . . . . . . . . . . . . . . . . 10
4.2. Informative References . . . . . . . . . . . . . . . . . 12
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 12
1. Introduction
An MPLS packet consists of a label stack, an optional "post-stack
header" (PSH) and an optional embedded packet (in that order). By
PSH, we mean existing artifacts such as Control Words, BIER headers
and the like, as well as new types of PSH being discussed in the MPLS
Open Design Team meetings. However, in the data plane, there are
scant clues regarding the PSH, and no clue as to the type of embedded
packet; this information is communicated via other means, such as the
routing protocols that signal the labels in the stack. Nonetheless,
in order to better handle an MPLS packet in the data plane, it is
common practice for network equipment to "guess" the type of embedded
packet. Such equipment may also need to process the post-stack
header. Both of these require parsing the data after the label
Kompella, et al. Expires 15 July 2023 [Page 2]
Internet-Draft 1st nibble January 2023
stack. To do this, the "first nibble" (the top four bits of the
first octet following the label stack) is often used.
The semantics and usage of the first nibble is not well documented,
nor are the assignments of values. This memo serves three purposes:
* To document the assignments already made
* To provide for the clear documentation of future assignments
through the creation of an "MPLS First Nibble registry"
* Provide a method to tracking usage by requiring more consistent
documentation
* To reiterate the importance that any MPLS packet not carrying
plain IPv4 or IPv6 packets MUST contain a PSH
There have been suggestions during discussions at the MPLS Open
Design Team meetings that this document may serve as a registry for
the PSH "headers of headers" types; however, this change needs WG
consensus.
1.1. Conventions and Definitions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
LSR: label switching router.
MPLS packet: one whose Layer 2 header declares the type to be MPLS.
For Ethernet, that means the Ethertype is 0x8847 or 0x8848.
Label Stack: (of an MPLS packet) all labels (four octet fields)
after the Layer 2 header, up to and including the label with the
BoS bit set ([RFC3032]).
MPLS First Nibble (MFN): the most significant four bits of the first
octet following the label stack.
MPLS Payload: all data after the label stack, including the MFN, an
optional post-stack header and the embedded packet.
Post-stack Header (PSH): optional field of interest to the egress
Kompella, et al. Expires 15 July 2023 [Page 3]
Internet-Draft 1st nibble January 2023
LSR (and possibly to transit LSRs). Examples include a control
word or an associated channel. The PSH MUST indicate its length,
so that a parser knows where the embedded packet starts.
Embedded Packet: All octets beyond the PSH (if any). This could be
an IPv4 or IPv6 packet (e.g., for traffic engineering of IP
packets, or for a Layer 3 VPN [RFC4364]), an Ethernet packet (for
VPLS ([RFC4761], [RFC4762]) or EVPN [RFC7432]), or some other type
of Layer 2 frame [RFC4446].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
X | Layer 2 Header | |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
TC S TTL
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
Y | Label-1 | TC |0| TTL | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label-2 | TC |0| TTL | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | TC |0| TTL | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label-n | TC |1| TTL | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 1: Example of an MPLS Packet With Label Stack
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
A | (MFN) | IP packet | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| data | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| end of IP packet | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 2
Kompella, et al. Expires 15 July 2023 [Page 4]
Internet-Draft 1st nibble January 2023
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
B | (MFN) | non-IP packet | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| data | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| end of non-IP packet | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+\
C | (MFN) | PSH | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PSH | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| end of PSH | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| embedded packet | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+/
Figure 4
Figure 1 shows an MPLS packet with Layer 2 header X and a label stack
Y ending with Label-n. Then, there are three examples of an MPLS
payload. The full MPLS packet thus would consist of [X Y A], or [X Y
B], or [X Y C].
A. The first payload is a bare IP packet, i.e., no PSH. The MFN
(MPLS First Nibble) in this case overlaps with the IP version number.
B. The next payload is a bare non-IP packet; again, no PSH. The MFN
here is the first nibble of the payload, whatever it happens to be.
C. The last example is an MPLS Payload that starts with a PSH
followed by the embedded packet. Here, the embedded packet could be
IP or non-IP.
2. Rationale
2.1. Why Look at the First Nibble
An MPLS packet can contain many types of embedded packet. The most
common types are:
Kompella, et al. Expires 15 July 2023 [Page 5]
Internet-Draft 1st nibble January 2023
1. An IPv4 packet (whose IP header has version number 4).
2. An IPv6 packet (whose IP header has version number 6).
3. A Layer 2 Ethernet frame (i.e., not including the Preamble or the
Start frame delimiter), starting with the destination MAC
address.
Many other packet types are possible, and in principle, any Layer 2
embedded packet is permissible; indeed, in the past, PPP, Frame Relay
and ATM packets were reasonably common.
In addition, there may be a post-stack header ahead of the embedded
packet, and this needs be to parsed. The MPLS First Nibble is
currently used for both of these purposes.
2.1.1. Load Balancing
There are four common ways to load balance an MPLS packet:
1. One can use the top label alone.
2. One can do better by using all the (non-SPL) labels in the stack.
3. One can do even better by "divining" the type of embedded packet,
and using fields from the guessed header.
4. One can do best by using either an Entropy Label [RFC6790] or a
FAT Pseudowire Label [RFC6391]; see Section 2.1.3.)
Load balancing based on just the top label means that all packets
with that top label will go the same way -- this is far from ideal.
Load balancing based on the entire label stack (not including SPLs)
is better, but may still be uneven. If, however, the embedded packet
is an IP packet, then the combination of (<source IP address>, <dest
IP address>, <transport protocol>, <source port>, and <dest port>)
from the IP header of the embedded packet forms an excellent basis
for load balancing. This is what is typically used for load
balancing IP packets.
An MPLS packet doesn't, however, carry a payload type identifier.
There is a simple (but dangerous) heuristic that is commonly used to
guess the type of the embedded packet. The first nibble, i.e., the
four most significant bits of the first octet, of an IP header
contains the IP version number. This in turn indicates where to find
the relevant fields for load balancing. The heuristic goes roughly
as follows:
Kompella, et al. Expires 15 July 2023 [Page 6]
Internet-Draft 1st nibble January 2023
2.1.1.1. Heuristic for Load Balancing
1. If the MFN is 0x4 (0100b), treat the payload as an IPv4 packet,
and find the relevant fields for load balancing on that basis.
2. If the MFN is 0x6 (0101b), treat the payload as an IPv6 packet,
and find the relevant fields for load balancing on that basis.
3. If the MFN is anything else, the MPLS payload is not an IP
packet; fall back to load balancing using the label stack.
This heuristic has been implemented in many (legacy) routers, and
performs well in the case of Figure 1, A. However, this heuristic
can work very badly for Figure 1, B. For example, if payload B is an
Ethernet frame, then the MFN is the first nibble of the OUI of the
destination MAC address, which can be 0x4 or 0x6, and if so would
lead to very bad load balancing. This behavior can happen to other
types of non-IP payload as well.
This in turn led to the idea of inserting a PSH (e.g., a pseudowire
control word [RFC4385], a DetNet control word [RFC8964] or a BIER
header [RFC8296]) where the MPLS First Nibble is NOT 0x4 or 0x6, to
explicitly prevent forwarding engines from confusing the MPLS payload
with an IP packet. [RFC8469] recommends the use of a control word
when the embedded packet is an Ethernet frame. RFC 8469 was
published at the request of the operator community and the IEEE RAC
as a result of operational difficulties with pseudowires that did not
contain the control word.
This memo introduces a requirement and a recommendation, the first
building on the above; the second deprecating the use of the
heuristic in Section 2.1.1.1. The intent of both of these is that
legacy routers continue to operate as they have, with no new problems
introduced as a result of this memo. However, new implementations
SHOULD follow these recommendations for more robust operation.
2.1.2. Requirement
Going forward, network equipment MUST use a post-stack header with an
MPLS First Nibble value that is not 0x4 or 0x6 in all cases when the
MPLS payload is not an IP packet. Effectively, Figure 1, B is
disallowed. [AGREED???]
This replaces the following text from [RFC4928], section 3, paragraph
3:
Kompella, et al. Expires 15 July 2023 [Page 7]
Internet-Draft 1st nibble January 2023
"It is REQUIRED, however, that applications depend upon in-order
packet delivery restrict the first nibble values to 0x0 and 0x1.
This will ensure that their traffic flows will not be affected if
some future routing equipment does similar snooping on some future
version(s) of IP."
This also replaces the following text from [RFC8469], section 4,
paragraph 1:
"This document updates [RFC4448] to state that both the ingress
provider edge (PE) and the egress PE SHOULD support the Ethernet PW
CW and that, if supported, the CW MUST be used."
2.1.3. Recommendation
It is RECOMMENDED that, going forward, if good load balancing of MPLS
packets is desired, either an Entropy Label or a FAT Pseudowire Label
SHOULD be used; furthermore, going forward, the heuristic in
Section 2.1.1.1 MUST NOT be used. [AGREED???]
A consequence of Recommendation 2 is that, while legacy routers may
look for a MPLS First Nibble of 0x4 or 0x6, no router will look for a
MPLS First Nibble of 0x7 (or whatever the next IP version number will
be) for load balancing purposes. This means that the values 0x4 and
0x6 are used to (sometimes incorrectly) identify IPv4 and IPv6
packets, but no other First Nibble values will be used to identify IP
packets.
This obviates the need for paragraph 4, section 3 in [RFC4928]:
"This behavior implies that if in the future an IP version is defined
with a version number of 0x0 or 0x1, then equipment complying with
this BCP would be unable to look past one or more MPLS headers, and
loadsplit traffic from a single LSP across multiple paths based on a
hash of specific fields in the IPv0 or IPv1 headers. That is, IP
traffic employing these version numbers would be safe from
disturbances caused by inappropriate loadsplitting, but would also
not be able to get the performance benefits."
This also expands the MFN Registry to all 16 possible values, not
just 0x0 and 0x1.
Kompella, et al. Expires 15 July 2023 [Page 8]
Internet-Draft 1st nibble January 2023
2.1.4. Parsing the Post-stack Header
Given the above recommendations on the use of a post-stack header and
future non-use of the heuristic (Section 2.1.1.1) via the use of
Entropy or FAT Pseudowire Labels, the main reason for creating a
First Nibble registry is to document the types of post-stack headers
that may follow a label stack, and to simplify their parsing.
2.2. Why Create a Registry
The MPLS WG is currently engaged in updating the MPLS architecture;
part of this work involves the use of post-stack headers. This is
not possible if post-stack header values are allocated on an ad hoc
basis, and their parsing and semantics is ill-specified. Consider
that the MPLS First Nibble value of 0x0 has two different formats,
depending on whether the post-stack header is a pseudowire control
word or a DetNet control word; disambiguation requires the context of
the service label. This was a considered decision; documenting this
would be helpful to future implementors.
With a registy, post-stack headers become easier to parse; the values
are unique, not needing means outside the data plane to interpret
them correctly; and their semantics and usage are documented. (Thank
you, IANA!)
2.3. Caveat
The use of the MPLS First Nibble stemmed from the desire to
heuristically identify IP packets for load balancing purposes. It
was then discovered that non-IP packets, misidentified as IP when the
heuristic failed, were being badly load balanced, leading to
[RFC4928]. This situation may confuse some as to relationship
between the MPLS First Nibble Registry and the IP Version Numbers
registry. These registries are quite different:
1. The IP Version Numbers registry's explicit purpose is to track IP
version numbers in an IP header.
2. The MPLS First Nibble registry's purpose is to track post-stack
header types.
The only intersection points between the two registries is for values
0x4 and 0x6 (for backward compatibility). There is no need to track
future IP version number allocations in the MPLS First Nibble
registry.
3. IANA Considerations
Kompella, et al. Expires 15 July 2023 [Page 9]
Internet-Draft 1st nibble January 2023
3.1. MPLS First Nibble Registry
This memo recommends the creation of an IANA registry called "The
MPLS First Nibble Registry" with the following values:
+=======+========================+===========+===================+
| Value | Meaning | Reference | Allocation Policy |
+=======+========================+===========+===================+
| 0x0 | PW Control Word | RFC 4385 | |
+-------+------------------------+-----------+-------------------+
| 0x0 | DetNet Control Word | RFC 8964 | |
+-------+------------------------+-----------+-------------------+
| 0x1 | PW Assoc Channel | RFC 4385 | |
+-------+------------------------+-----------+-------------------+
| 0x2 | Unallocated | | Standards Action |
+-------+------------------------+-----------+-------------------+
| 0x3 | Unallocated | | Standards Action |
+-------+------------------------+-----------+-------------------+
| 0x4 | IPv4 header | RFC 791 | |
+-------+------------------------+-----------+-------------------+
| 0x5 | BIER header | RFC 8296 | |
+-------+------------------------+-----------+-------------------+
| 0x6 | IPv6 header | RFC 8200 | |
+-------+------------------------+-----------+-------------------+
| 0x7-e | Unallocated | | Standards Action |
+-------+------------------------+-----------+-------------------+
| 0xf | Reserved for expansion | | Standards Action |
+-------+------------------------+-----------+-------------------+
Table 1: MPLS First Nibble Values
3.1.1. Allocation Policy
All new values registered here MUST use the Standards Action policy
[RFC8126].
4. References
4.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
Kompella, et al. Expires 15 July 2023 [Page 10]
Internet-Draft 1st nibble January 2023
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001,
<https://www.rfc-editor.org/info/rfc3032>.
[RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson,
"Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for
Use over an MPLS PSN", RFC 4385, DOI 10.17487/RFC4385,
February 2006, <https://www.rfc-editor.org/info/rfc4385>.
[RFC4928] Swallow, G., Bryant, S., and L. Andersson, "Avoiding Equal
Cost Multipath Treatment in MPLS Networks", BCP 128,
RFC 4928, DOI 10.17487/RFC4928, June 2007,
<https://www.rfc-editor.org/info/rfc4928>.
[RFC6391] Bryant, S., Ed., Filsfils, C., Drafz, U., Kompella, V.,
Regan, J., and S. Amante, "Flow-Aware Transport of
Pseudowires over an MPLS Packet Switched Network",
RFC 6391, DOI 10.17487/RFC6391, November 2011,
<https://www.rfc-editor.org/info/rfc6391>.
[RFC6790] Kompella, K., Drake, J., Amante, S., Henderickx, W., and
L. Yong, "The Use of Entropy Labels in MPLS Forwarding",
RFC 6790, DOI 10.17487/RFC6790, November 2012,
<https://www.rfc-editor.org/info/rfc6790>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8296] Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
Tantsura, J., Aldrin, S., and I. Meilik, "Encapsulation
for Bit Index Explicit Replication (BIER) in MPLS and Non-
MPLS Networks", RFC 8296, DOI 10.17487/RFC8296, January
2018, <https://www.rfc-editor.org/info/rfc8296>.
[RFC8469] Bryant, S., Malis, A., and I. Bagdonas, "Recommendation to
Use the Ethernet Control Word", RFC 8469,
DOI 10.17487/RFC8469, November 2018,
<https://www.rfc-editor.org/info/rfc8469>.
Kompella, et al. Expires 15 July 2023 [Page 11]
Internet-Draft 1st nibble January 2023
[RFC8964] Varga, B., Ed., Farkas, J., Berger, L., Malis, A., Bryant,
S., and J. Korhonen, "Deterministic Networking (DetNet)
Data Plane: MPLS", RFC 8964, DOI 10.17487/RFC8964, January
2021, <https://www.rfc-editor.org/info/rfc8964>.
4.2. Informative References
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
2006, <https://www.rfc-editor.org/info/rfc4364>.
[RFC4446] Martini, L., "IANA Allocations for Pseudowire Edge to Edge
Emulation (PWE3)", BCP 116, RFC 4446,
DOI 10.17487/RFC4446, April 2006,
<https://www.rfc-editor.org/info/rfc4446>.
[RFC4761] Kompella, K., Ed. and Y. Rekhter, Ed., "Virtual Private
LAN Service (VPLS) Using BGP for Auto-Discovery and
Signaling", RFC 4761, DOI 10.17487/RFC4761, January 2007,
<https://www.rfc-editor.org/info/rfc4761>.
[RFC4762] Lasserre, M., Ed. and V. Kompella, Ed., "Virtual Private
LAN Service (VPLS) Using Label Distribution Protocol (LDP)
Signaling", RFC 4762, DOI 10.17487/RFC4762, January 2007,
<https://www.rfc-editor.org/info/rfc4762>.
[RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
2015, <https://www.rfc-editor.org/info/rfc7432>.
Authors' Addresses
Kireeti Kompella (editor)
Juniper Networks
1133 Innovation Way
Sunnyvale, 94089
United States of America
Phone: +1-408-745-2000
Email: kireeti.ietf@gmail.com
Stewart Bryant
University of Surrey 5GIC
Email: sb@stewartbryant.com
Kompella, et al. Expires 15 July 2023 [Page 12]
Internet-Draft 1st nibble January 2023
Matthew Bocci
Nokia
Email: matthew.bocci@nokia.com
Greg Mirsky
Ericsson
Email: gregimirsky@gmail.com
Loa Andersson
Bronze Dragon Consulting
Email: loa@pi.nu
Kompella, et al. Expires 15 July 2023 [Page 13]