Network Working Group E. Lear
Internet-Draft O. Friel
Intended status: Standards Track N. Cam-Winget
Expires: December 31, 2018 Cisco Systems
June 29, 2018
Bootstrapping Key Infrastructure over EAP
draft-lear-eap-teap-brski-00
Abstract
In certain environments, in order for a device to establish any layer
three communications, it is necessary for that device to be properly
credentialed. This is a relatively easy problem to solve when a
device is associated with a human being and has both input and
display functions. It is less easy when the human, input, and
display functions are not present. To address this case, this memo
specifies extensions to the Tunnel Extensible Authentication Protocol
(TEAP) method that leverages Bootstrapping Remote Secure Key
Infrastructures (BRSKI) in order to provide a credential to a device
at layer two.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 31, 2018.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
Lear, et al. Expires December 31, 2018 [Page 1]
Internet-Draft BRSKI TEAP EAP June 2018
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
2. TEAP BRSKI Architecture . . . . . . . . . . . . . . . . . . . 3
3. BRSKI Bootstrap and Enroll Operation . . . . . . . . . . . . 4
3.1. Executing BRSKI in a TEAP Tunnel . . . . . . . . . . . . 5
4. PKI Certificate Authority Considerations . . . . . . . . . . 8
4.1. TEAP Tunnel Establishment . . . . . . . . . . . . . . . . 8
4.2. BRSKI Trust Establishment . . . . . . . . . . . . . . . . 9
5. Channel and Crypto Binding . . . . . . . . . . . . . . . . . 10
6. Protocol Flows . . . . . . . . . . . . . . . . . . . . . . . 10
6.1. TEAP Server Grants Access . . . . . . . . . . . . . . . . 11
6.2. TEAP Server Instructs Client to Perform BRSKI Flow . . . 12
6.3. TEAP Server Instructs Client to Reenroll . . . . . . . . 13
6.4. Out of Band Reenroll . . . . . . . . . . . . . . . . . . 14
7. TEAP TLV Formats . . . . . . . . . . . . . . . . . . . . . . 15
7.1. BRSKI TLVs . . . . . . . . . . . . . . . . . . . . . . . 15
7.1.1. BRSKI-RequestVoucher TLV . . . . . . . . . . . . . . 15
7.1.2. BRSKI-Voucher TLV . . . . . . . . . . . . . . . . . . 15
7.1.3. BRSKI-VoucherStatus TLV . . . . . . . . . . . . . . . 15
7.1.4. EnrollmentStatus TLV . . . . . . . . . . . . . . . . 15
7.1.5. CSR-Attributes TLV . . . . . . . . . . . . . . . . . 15
7.2. Existing TEAP TLV Specifications . . . . . . . . . . . . 15
7.2.1. PKCS#10 TLV . . . . . . . . . . . . . . . . . . . . . 16
8. Fragmentation . . . . . . . . . . . . . . . . . . . . . . . . 16
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16
10. Security Considerations . . . . . . . . . . . . . . . . . . . 16
11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 16
12. Informative References . . . . . . . . . . . . . . . . . . . 16
Appendix A. Changes from Earlier Versions . . . . . . . . . . . 17
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 17
1. Introduction
[I-D.ietf-anima-bootstrapping-keyinfra] (BRSKI) specifies a means to
provision credentials to be used as credentials to operationally
access networks. It was designed as a standalone means where some
limited access to an IP network is already available. This is not
always the case. For example, IEEE 802.11 networks generally require
authentication prior to any form of address assignment. While it is
Lear, et al. Expires December 31, 2018 [Page 2]
Internet-Draft BRSKI TEAP EAP June 2018
possible to assign an IP address to a device on some form of an open
network, or to accept some sort of default credential to establish
initial IP connectivity, the steps that would then follow might well
require that the device is placed on a new network, requiring
reseting all layer three parameters.
A more natural approach in such cases is to more tightly bind the
provisioning of credentials with the authentication mechanism. One
such way to do this is to make use of the Extensible Authentication
Protocol (EAP) [RFC3748] and the Tunnel Extensible Authentication
Protocol (TEAP) method [RFC7170]. Thus we define new TEAP Type-
Length-Value (TLV) objects that can be used to transport the BRSKI
protocol messages within the context of a TEAP TLS tunnel.
[RFC7170] discusses the notion of provisioning peers. Several
different mechanisms are available. Section 3.8 of that document
acknowledges the concept of not initially authenticating the outer
TLS session so that provisioning may occur. In addition, exchange of
multiple TLV messages between client and EAP server permits multiple
provisioning steps.
1.1. Terminology
The reader is presumed to be familiar with EAP terminology as stated
in [RFC3748]. In addition, the following terms are commonly used in
this document.
o BRSKI: Bootstrapping Remote Secure Key Infrastructures, as defined
in [I-D.ietf-anima-bootstrapping-keyinfra]. The term is also used
to refer to the flow described in that document.
o EST: Enrollment over Secure Transport, as defined in [RFC7030].
o voucher: a signed json object as defined in [RFC8366].
2. TEAP BRSKI Architecture
The TEAP BRSKI architecture is illustrated in Section 3. The device
talks to the TEAP server via the Authenticator as per any normal EAP
exchange. There is no need for an inner EAP method server, and there
is no explicit EAP method type defined for BRSKI.
The architecture illustrated shows the TEAP server and Registrar
function as being two logically separate entities, however the BRSKI
Registrar functionality may be integrated into the TEAP server. The
device is not explicitly aware of where the Registrar functionality
is deployed when executing BRSKI inside a TEAP tunnel. Note that the
device may connect directly to the Registrar for the purposes of
Lear, et al. Expires December 31, 2018 [Page 3]
Internet-Draft BRSKI TEAP EAP June 2018
certificate reenrollment, but this happens outside the context to
801.1X and TEAP authentication.
The Registrar in turn communicates with the BRSKI MASA service for
the purposes of getting signed vouchers. [[TODO: I guess we should
mention TEAP server talking to vendor default Registrar in the
cloud]]
The Registrar also comunicates with a Certificate Authority in order
to issue LDevIDs. The architecture shows the Registrar and CA as
being two logically separate entities, however the CA may be
integrated into the Registrar. The device is not explicitly aware of
whether the CA and Registrar functions are integrated.
+--------+ +---------+ +--------+ +---------+ +------+
| | | | | | | |<--->| MASA |
| | | Authen- | | TEAP | | BRSKI | +------+
| Device |<--->| ticator |<--->| server |<--->|Registrar|
| | | | | | | | +------+
| | | | | | | |<--->| CA |
+--------+ +---------+ +--------+ +---------+ +------+
3. BRSKI Bootstrap and Enroll Operation
This section summarises the current BRSKI operation. The BRSKI flow
assumes the device has an IDevID and has a manufacturer installed
trust anchor that can be used to validate the BRSKI voucher. The
BRSKI flow compromises serveral main steps from the perspective of
the device:
o Step 1: Device discovers the Registrar
o Step 2: Device establishes provisional TLS connection to Registrar
o Step 3: Device sends voucher request message and receives signed
voucher response
o Step 4: Device validates voucher and validates provisional TLS
connection to Registrar
o Step 5: Device sends Voucher Status Telemetry message
o Step 6: Device downloads additional local domain CA information
o Step 7: Device downloads Certificate Signing Reqeust (CSR)
attributes
Lear, et al. Expires December 31, 2018 [Page 4]
Internet-Draft BRSKI TEAP EAP June 2018
o Step 8: Device does an EST enroll to obtain an LDevID
o Step 9: Device sends Enrollment Status Telemetry message
o Step 10: Device periodically reenrolls via EST to refresh its
LDevID
Most of the operational steps require the device, and thus its
internal state machine, to automatically complete the next step
without being explicitly instructed to do so by the Registrar. For
example, the Registrar does not explicitly tell the device to
download additional local domain CA information, or to do an EST
enroll to obtain an LDevID.
3.1. Executing BRSKI in a TEAP Tunnel
This section outlines how the main BRSKI steps outlined above map to
TEAP, and how BRSKI and enrollment can be accomplished inside a TEAP
TLS tunnel. The following new TEAP TLVs are introduced:
o BRSKI-VoucherRequest
o BRSKI-Voucher
o BRSKI-VoucherStatus
o EnrollmentStatus
o CSR-Attributes
The following steps outline how the above BRSKI flow maps to TEAP.
o Step 1: Device discovers the Registrar
When BRSKI is executed in a TEAP tunnel, the device exchanges BRSKI
TLVs with the TEAP server. The discovery process for devices is
therefore the standard wired or wireless LAN EAP server discovery
process. The discovery processes outlined in section 4 of
[I-D.ietf-anima-bootstrapping-keyinfra] are not required for initial
discovery of the Registrar.
o Step 2: Device establishes provisional TLS connection to Registrar
The device establishes an outer TEAP tunnel with the TEAP server and
does not validate the server certificate. The device presents its
LDevID as its identity certificate if it has a valid LDevID,
otherwise it presents its IDevID. Server policy may also be used to
Lear, et al. Expires December 31, 2018 [Page 5]
Internet-Draft BRSKI TEAP EAP June 2018
control which certificate the device is allowed present, as described
in section Section 4.
If the presented credential is sufficient to grant access, the TEAP
server can return an EAP-Success immediately. The device may still
send a BRSKI-RequestVoucher TLV in response to the EAP-Success if it
does not have, but requires, trust anchors for validating the TEAP
server certificate.
If the TEAP server requires that the device execute a BRSKI flow, it
sends a Request-Action TLV that includes a BRSKI-VoucherRequest TLV.
For example, if the device presented its IDevID but the TEAP server
requires an LDevID.
The TEAP server may also require the device to reenroll, for example,
if the device presented a valid LDevID that is very closed to
expiration. The server may instruct a device to reenroll by sending
a Request-Action TLV that includes a zero byte length PKCS#10 TLV.
o Step 3: Device sends voucher request message and receives signed
voucher response
The device sends a BRSKI-RequestVoucher TLV to the TEAP server. The
TEAP server forwards the RequestVoucher message to the MASA server,
and the MASA server replies with a signed voucher. The TEAP server
sends a BRSKI-Voucher TLV to the device.
If the MASA server does not issue a signed voucher, the TEAP server
sends an EAP-Error TLV with a suitable error code to the device.
o Step 4: Device validates voucher and validates provisional TLS
connection to Registrar
The device validates the signed voucher using its manufacturer
installed trust anchor, and uses the CA information in the voucher to
validate the outer TEAP TLS connection to the TEAP server.
If the device fails to validate the voucher, or fails to validate the
outer TEAP TLS connection, then it sends a BRSKI-VoucherStatus TLV
indicating failure to the TEAP server.
o Step 5: Device sends Voucher Status Telemetry message
On successfully validating the voucher and outer TEAP TLS connection,
the device sends a BRSKI-VoucherStatus TLV to the TEAP server.
Once step 5 is complete, the device has completed the BRSKI flow and
has established trust with the network.
Lear, et al. Expires December 31, 2018 [Page 6]
Internet-Draft BRSKI TEAP EAP June 2018
o Step 6: Device downloads additional local domain CA information
On completion of the BRSKI flow, the device SHOULD send a Trusted-
Server-Root TLV to the TEAP server in order to discover additional
local domain CAs.
o Step 7: Device downloads CSR attributes
On completion of step 6, the device MUST send a CSR-Attributes TLV to
the TEAP server in order to discover the correct fields to include
when it enrolls to get an LDevID.
o Step 8: Device does an EST enroll to obtain an LDevID
When executing the BRSKI flow inside a TEAP tunnel, the device does
not directly leverage EST when doing its initial enroll. Instead,
the device uses the existing TEAP PKCS#10 and PCKS#7 TEAP mechanisms.
Once the BRSKI flow is complete, the device can now send a PKCS#10
TLV to enroll and request an LDevID. If the TEAP server instructed
the device to start the BRSKI flow via a Request-Action TLV that
includes a BRSKI-RequestVoucher TLV, then the device MUST send a
PKCS#10 in order to start the enroll process. The TEAP server will
handle the PKCS#10 and ultimately return a PKCS#7 including an LDevID
to the device.
If the TEAP server granted the device access on completion of the
outer TEAP TLS tunnel in step 2 without sending a Request-Action TLV,
the device does not have to send a PKCS#10 to enroll.
o Step 9: Device sends Enrollment Status Telemetry message
On completion of certificate enrollment, the device sends an
EnrollmentStatus TLV to the TEAP server.
o Step 10: Device periodically reenrolls to refresh its LDevID
When a device's LDevID is close to expiration, there are two options
for re-enrollment in order to obtain a fresh LDevID. As outlined in
Step 2 above, the TEAP server may instruct the device to reenroll by
sending a Request-Action TLV including a PKCS#10 TLV. If the TEAP
server explicilty instructs the device to reenroll via these TLV
exchange, then the device MUST send a PKCS#10 to reenroll and request
a fresh LDevID.
However, the device should be capabale of autonomic reenrollment if
it determines that its LDevID is close to expiration wihtout waiting
Lear, et al. Expires December 31, 2018 [Page 7]
Internet-Draft BRSKI TEAP EAP June 2018
for explicit instruction from the TEAP server. There are two options
to do this.
Option 1: The device reenrolls for a new LDevID directly with the EST
CA outside the context of the 802.1X TEAP authentication flow. The
device uses the Registrar discovery mechanisms oulined in
[I-D.ietf-anima-bootstrapping-keyinfra] to discover the Registrar and
the device sends the EST reenroll messages to the discovered
Registrar endpoint. No new TEAP TLVs are defined to facilitate
discover of the Registrar or EST endpoints inside the context of the
TEAP tunnel.
Option 2: When the device is perfroming a periodic 802.1X
authentication using its current LDevID, it reenrolls for a new
LDevID by sending a PKCS#10 TLV inside the TEAP TLS tunnel.
4. PKI Certificate Authority Considerations
Careful consideration must be given to PKI certificate authority
handling when:
o Establishing the TEAP tunnel
o Establishing trust using BRSKI
These are described in more detail here.
4.1. TEAP Tunnel Establishment
The client sends its ClientHello to initiate TLS tunnel
establishment. It is possible for the TEAP server to restrict the
certificates that the client can use for tunnel establishment by
including a list of CA distinguished names in the
certificate_authorities field in the CertificateRequest message.
Network operators may want to do this in order to restrict netwok
access to clients that have a certificate signed by one of a small
set of trusted manufacturer/supplier CAs. If the client has both an
IDevID and an LDevID, the client should present the LDevID in
preference to its IDevID if allowed by server policy.
In practice, network operators will likely want to onboard devices
from a large number of device manufacturers, with each manufacturer
using a different root CA when issuing IDevIDs. If the number of
different manufacturer root CAs is large, this could result in very
large TLS handshake messages. Operators may prefer to include no CAs
in the certificate_authorities field thus allowing devices to present
IDevIDs signed by any CA when establishing the TEAP tunnel, and
instead enforce policy at LDevID enrollment time.
Lear, et al. Expires December 31, 2018 [Page 8]
Internet-Draft BRSKI TEAP EAP June 2018
It is recommended that the client validate the certificate presented
by the server in the server's Certificate message, but this may not
be possible for bootstrapping clients that do not have appropriate
trust anchors installed yet. If the client is bootstrapping and has
not yet completed a BRSKI flow, it will not have trust anchors
installed yet, and thus will not be able to validate the server's
certificate. The client must however note the certificate presented
by the server for (i) inclusion in the BRSKI-RequestVoucher TLV and
for (ii) validation once the client has discovered the local domain
trust anchors.
If the client does not present a suitable certificate to the server,
the server MUST terminate the connection and fail the EAP request.
On establishment of the outer TLS tunnel, the TEAP server will make a
policy decision on next steps. Possible policy decisions include:
o Option 1: Server grants client full network access and returns
EAP-Success. This will typically happen when the client presents
a valid LDevID. Network policy may grant client network access
based on IDevID without requiring the device to enroll to obtain
an LDevID.
o Option 2: Server requires that client perform a full BRSKI flow,
and then enroll to get an LDevID. This will typically happen when
the client presents a valid IDevID and network policy requires all
clients to have LDevIDs. The server sends a Request-Action TLV
that includes a BRSKI-RequestVoucher TLV to the client to instruct
it to start the BRSKI flow.
o Option 3: Server requires that the client reenroll to obtain a new
LDevID. This could happen when the client presents a valid LDevID
that is very close to expiration time, or the server's policy
requires an LDevID update. The server sends an Action-Request TLV
including a PKCS#10 TLV to the client to instruct it to reenroll.
4.2. BRSKI Trust Establishment
If the server requires that client perform a full BRSKI flow, it
sends a Request-Action TLV that includes a zero byte length BRSKI-
RequestVoucher TLV to the client. The client sends a new BRSKI-
RequestVoucher TLV to the server, which contains all data specified
in [I-D.ietf-anima-bootstrapping-keyinfra] section 5.2. The client
includes the server certificate it received in the server's
Certificate message during outer TLS tunnel establishment in the
proximity-registrar-cert field. The client signs the request using
its IDevID.
Lear, et al. Expires December 31, 2018 [Page 9]
Internet-Draft BRSKI TEAP EAP June 2018
The server includes all additional information as required by
[I-D.ietf-anima-bootstrapping-keyinfra] section 5.4 and signs the
request prior to forwarding to the MASA.
The MASA responds as per [I-D.ietf-anima-bootstrapping-keyinfra]
section 5.5. The response may indicate failure and the server should
react accordingly to failures by sending a failure response to the
client, and failing the TEAP method.
If the MASA replies with a signed voucher and a successful result,
the server then forwards this response to the client in a BRSKI-
Voucher TLV.
When the client receives the signed voucher, it validates the
signature using its built in trust anchor list, and extracts the
pinned-domain-cert field. The client must use the CA included in the
pinned-domain-cert to validate the certificate that was presented by
the server when establishing the outer TLS tunnel. If this
certificate validation fails, the client must fail the TEAP request
and not connect to the network.
If the client successfully validates the server certificate, then it
must send voucher status telemetry, as required by
[I-D.ietf-anima-bootstrapping-keyinfra] section 5.6 to the server, in
a new BRSKI-VoucherTelemetry TLV.
5. Channel and Crypto Binding
As the TEAP BRSKI flow does not define or require an inner EAP
method, there is no explicit need for exchange of Channel-Binding
TLVs between the device and the TEAP server.
The TEAP BRSKI TLVs are expected to occur at the beginning of the
TEAP Phase 2 and MUST occur before the final Crypto-Binding TLV.
This draft does not exclude the possibility of having other EAP
methods occur following the TEAP BRSKI TLVs and as such, the Crypto-
Binding TLV process rules as defined in [RFC7170] apply.
6. Protocol Flows
This section outlines protocol flows that map to the 3 server policy
options described in section Section 4.1. The protocol flows
illustrate a TLS1.2 exchange.
[[TODO]] MISSING EAP Start/identity/Crypto binding, etc. Flows
illustrative, but not 100% accurate.
Lear, et al. Expires December 31, 2018 [Page 10]
Internet-Draft BRSKI TEAP EAP June 2018
6.1. TEAP Server Grants Access
+--------+ +-------------+ +------+
| Client | | TEAP-Server | | MASA |
+--------+ +-------------+ +------+
| | |
| ClientHello | |
|------------------------>| |
| ServerHello, | |
| Certificate(1), | |
| ServerKeyExchange, | |
| CertificateRequest(2), | |
| ServerHelloDone, | |
|<------------------------| |
| Certificate(3), | |
| ClientKeyExchange, | |
| CertificateVerify, | |
| ChangeCipherSpec, | |
| Finished | |
|------------------------>| |
| ChangeCipherSpec, | |
| Finished | |
|<------------------------| |
| Crypto-Binding TLV | |
|<------------------------| |
| Crypto-Binding TLV | |
|------------------------>| |
| Result TLV | |
|<------------------------| |
| Result TLV | |
|------------------------>| |
| EAP-Success | |
|<------------------------| |
Figure 1: TEAP Server Grants Access
Notes:
(1) If the client has completed the BRSKI flow yet, it must validate
the Certificate received from the server. If the client has not yet
completed the BRSKI flow, then it provisionally accepts the server
Certificate and must validate it later once BRSKI is complete.
(2) The server may include certificate_authorities field in the
CertificateRequest message in order to restrict the identity
certificates that the device is allowed present.
Lear, et al. Expires December 31, 2018 [Page 11]
Internet-Draft BRSKI TEAP EAP June 2018
(3) The device will present its LDevID, if it has one, in preference
to its IDevID, if allowed by server policy.
6.2. TEAP Server Instructs Client to Perform BRSKI Flow
+--------+ +-------------+ +------+
| Client | | TEAP-Server | | MASA |
+--------+ +-------------+ +------+
| | |
| ClientHello | |
|------------------------>| |
| ServerHello, etc.(1) | |
|<------------------------| |
| etc., Finished | |
|------------------------>| |
| etc., Finished | |
|<------------------------| |
| BRSKI-RequestAction(2) | |
|<------------------------| |
| BRSKI-RequestVoucher(3) | |
|------------------------>| RequestVoucher |
| |--------------->|
| | Voucher |
| BRSKI-Voucher(4) |<---------------|
|<------------------------| |
| BRSKI-VoucherStatus | |
|------------------------>| |
| Trusted-Server-Root | |
|------------------------>| |
| Trusted-Server-Root | |
|<------------------------| |
| CSR-Attributes | |
|------------------------>| |
| CSR-Attributes | |
|<------------------------| |
| PKCS#10 | |
|------------------------>| |
| PKCS#7 | |
|<------------------------| |
| EnrollmentStatus | |
|------------------------>| |
| Crypto-Binding TLV | |
|<------------------------| |
| Crypto-Binding TLV | |
|------------------------>| |
| Result TLV | |
|<------------------------| |
| Result TLV | |
Lear, et al. Expires December 31, 2018 [Page 12]
Internet-Draft BRSKI TEAP EAP June 2018
|------------------------>| |
| EAP-Success | |
|<------------------------| |
Figure 2: TEAP Server Instructs Client to Perform BRSKI Flow
Notes:
(1) If the client has not yet completed the BRSKI flow, then it
provisionally accepts the server certificate and must validate it
later once BRSKI is complete.
(2) The server instructs the client to start the BRSKI flow by
sending a RequestAction TLV that includes a BRSKI-RequestVoucher TLV.
(3) The client includes the certificate it received from the server
in the RequestVoucher message.
(4) Once the client receives and validates the voucher signed by the
MASA, it must verify the certificate it previously received from the
server.
6.3. TEAP Server Instructs Client to Reenroll
Lear, et al. Expires December 31, 2018 [Page 13]
Internet-Draft BRSKI TEAP EAP June 2018
+--------+ +-------------+ +------+
| Client | | TEAP-Server | | MASA |
+--------+ +-------------+ +------+
| | |
| ClientHello | |
|----------------------->| |
| ServerHello, etc. | |
|<-----------------------| |
| etc., Finished | |
|----------------------->| |
| etc., Finished | |
|<-----------------------| |
| RequestAction: PKCS#10 | |
|<-----------------------| |
| CSR-Attributes | |
|----------------------->| |
| CSR-Attributes | |
|<-----------------------| |
| PKCS#10 | |
|----------------------->| |
| PKCS#7 | |
|<-----------------------| |
| EnrollmentStatus | |
|----------------------->| |
| Crypto-Binding TLV | |
|<-----------------------| |
| Crypto-Binding TLV | |
|----------------------->| |
| Result TLV | |
|<-----------------------| |
| Result TLV | |
|----------------------->| |
| EAP-Success | |
|<-----------------------| |
Figure 3: TEAP Server Instructs Client to Reenroll
[[TODO: Hmm, as BRSKI mandates client requests CSR-Attributes, should
the server send a RequestAction and include two TLVs: one CSR-
Attributes and one PKCS#10 ? ]]
6.4. Out of Band Reenroll
This section shows how the device does a reenroll to refresh its
LDEvID directly against the Registrar outside the context of the TEAP
tunnel.
Lear, et al. Expires December 31, 2018 [Page 14]
Internet-Draft BRSKI TEAP EAP June 2018
7. TEAP TLV Formats
7.1. BRSKI TLVs
BRSKI defines 6 new TEAP TLVs. The following table indicates whether
the TLVs can be included in Request messages from TEAP server to
device, or Response messages from device to TEAP server.
+------------------------+----------+
| TLV | Message |
+------------------------+----------+
| BRSKI-VoucherRequest | Response |
| BRSKI-Voucher | Request |
| BRSKI-VoucherStatus | Response |
| EnrollmentStatus | Response |
| CSR-Attributes | Response |
+------------------------+----------+
These new TLVs are detailed in this section.
7.1.1. BRSKI-RequestVoucher TLV
To be completed.
7.1.2. BRSKI-Voucher TLV
To be completed.
7.1.3. BRSKI-VoucherStatus TLV
To be completed.
7.1.4. EnrollmentStatus TLV
To be completed.
7.1.5. CSR-Attributes TLV
To be completed.
7.2. Existing TEAP TLV Specifications
This section documents allowed usage of existing TEAP TLVs. The
definition of the TLV is not changed, however clarifications on
allowed values for the TLV fields is documented.
Lear, et al. Expires December 31, 2018 [Page 15]
Internet-Draft BRSKI TEAP EAP June 2018
7.2.1. PKCS#10 TLV
[RFC7170] defines the PKCS#10 TLV as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|M|R| TLV Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PKCS#10 Data...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
[RFC7170] does not explicitly allow a Length value of zero.
A Length value of zero is allowed for this TLV when the TEAP server
sends a Request-Action TLV with a child PKCS#10 TLV to the client.
In this scenario, there is no PKCS#10 Data included in the TLV.
Clients MUST NOT send a zero length PKCS#10 TLV to the server.
8. Fragmentation
TLS is expected to provide fragmentation support. Thus EAP-TEAP-
BRSKI does not specifically provide any, as it is only expected to be
used as an inner method to TEAP.
9. IANA Considerations
TBD.
10. Security Considerations
There will be many.
11. Acknowledgments
The authors would like to thank Brian Weis for his assistance.
12. Informative References
[I-D.ietf-anima-bootstrapping-keyinfra]
Pritikin, M., Richardson, M., Behringer, M., Bjarnason,
S., and K. Watsen, "Bootstrapping Remote Secure Key
Infrastructures (BRSKI)", draft-ietf-anima-bootstrapping-
keyinfra-16 (work in progress), June 2018.
Lear, et al. Expires December 31, 2018 [Page 16]
Internet-Draft BRSKI TEAP EAP June 2018
[RFC3748] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
Levkowetz, Ed., "Extensible Authentication Protocol
(EAP)", RFC 3748, DOI 10.17487/RFC3748, June 2004,
<https://www.rfc-editor.org/info/rfc3748>.
[RFC7030] Pritikin, M., Ed., Yee, P., Ed., and D. Harkins, Ed.,
"Enrollment over Secure Transport", RFC 7030,
DOI 10.17487/RFC7030, October 2013,
<https://www.rfc-editor.org/info/rfc7030>.
[RFC7170] Zhou, H., Cam-Winget, N., Salowey, J., and S. Hanna,
"Tunnel Extensible Authentication Protocol (TEAP) Version
1", RFC 7170, DOI 10.17487/RFC7170, May 2014,
<https://www.rfc-editor.org/info/rfc7170>.
[RFC8366] Watsen, K., Richardson, M., Pritikin, M., and T. Eckert,
"A Voucher Artifact for Bootstrapping Protocols",
RFC 8366, DOI 10.17487/RFC8366, May 2018,
<https://www.rfc-editor.org/info/rfc8366>.
Appendix A. Changes from Earlier Versions
Draft -00:
o Initial revision
Authors' Addresses
Eliot Lear
Cisco Systems
Richtistrasse 7
Wallisellen CH-8304
Switzerland
Phone: +41 44 878 9200
Email: lear@cisco.com
Owen Friel
Cisco Systems
170 W. Tasman Dr.
San Jose, CA 95134
United States
Email: ofriel@cisco.com
Lear, et al. Expires December 31, 2018 [Page 17]
Internet-Draft BRSKI TEAP EAP June 2018
Nancy Cam-Winget
Cisco Systems
170 W. Tasman Dr.
San Jose, CA 95134
United States
Email: ncamwing@cisco.com
Lear, et al. Expires December 31, 2018 [Page 18]