Benchmarking Methodology Working Group G. Lencse
Internet-Draft Szechenyi Istvan University
Intended status: Informational K. Shima
Expires: 5 September 2022 IIJ Innovation Institute
4 March 2022
Benchmarking Methodology for Stateful NATxy Gateways using RFC 4814
Pseudorandom Port Numbers
draft-lencse-bmwg-benchmarking-stateful-03
Abstract
RFC 2544 has defined a benchmarking methodology for network
interconnect devices. RFC 5180 addressed IPv6 specificities and it
also provided a technology update, but excluded IPv6 transition
technologies. RFC 8219 addressed IPv6 transition technologies,
including stateful NAT64. However, none of them discussed how to
apply RFC 4814 pseudorandom port numbers to any stateful NAT (NAT44,
NAT64, NAT66) technologies. We discuss why using pseudorandom port
numbers with stateful NAT gateways is a hard problem and recommend a
solution.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 5 September 2022.
Copyright Notice
Copyright (c) 2022 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Lencse & Shima Expires 5 September 2022 [Page 1]
Internet-Draft Benchmarking Stateful Gateways March 2022
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. Pseudorandom Port Numbers and Stateful Translation . . . . . 3
3. Test Setup and Terminology . . . . . . . . . . . . . . . . . 4
4. Recommended Benchmarking Method . . . . . . . . . . . . . . . 5
4.1. Restricted Port Number Ranges . . . . . . . . . . . . . . 5
4.2. Preliminary Test Phase . . . . . . . . . . . . . . . . . 6
4.3. Consideration of the Cases of Stateful Operation . . . . 7
4.4. Control of the Connection Tracking Table Entries . . . . 8
4.5. Measurement of the Maximum Connection Establishment
Rate . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.6. Real Test Phase . . . . . . . . . . . . . . . . . . . . . 10
4.7. Measurement of the Connection Tear Down Rate . . . . . . 11
4.8. Writing and Reading Order of the State Table . . . . . . 11
5. Implementation and Experience . . . . . . . . . . . . . . . . 12
6. Limitations of using UDP as Transport Layer Protocol . . . . 12
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13
9. Security Considerations . . . . . . . . . . . . . . . . . . . 13
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 13
10.1. Normative References . . . . . . . . . . . . . . . . . . 13
10.2. Informative References . . . . . . . . . . . . . . . . . 13
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 15
A.1. 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A.2. 01 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A.3. 02 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A.4. 03 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15
1. Introduction
[RFC2544] has defined a comprehensive benchmarking methodology for
network interconnect devices, which is still in use. It was mainly
IP version independent, but it used IPv4 in its examples. [RFC5180]
addressed IPv6 specificities and also added technology updates, but
declared IPv6 transition technologies out of its scope. [RFC8219]
addressed the IPv6 transition technologies, including stateful NAT64.
It has reused several benchmarking procedures from [RFC2544] (e.g.
throughput, frame loss rate), it has redefined the latency
measurement, and added further ones, e.g. the PDV (packet delay
Lencse & Shima Expires 5 September 2022 [Page 2]
Internet-Draft Benchmarking Stateful Gateways March 2022
variation) measurement.
However, none of them discussed, how to apply [RFC4814] pseudorandom
port numbers, when benchmarking stateful NATxy (NAT44, NAT64, NAT66)
gateways. We are not aware of any other RFCs that address this
question.
First, we discuss why using pseudorandom port numbers with stateful
NATxy gateways is a hard problem.
Then we recommend a solution.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Pseudorandom Port Numbers and Stateful Translation
In its appendix, [RFC2544] has defined a frame format for test frames
including specific source and destination port numbers. [RFC4814]
recommends to use pseudorandom and uniformly distributed values for
both source and destination port numbers. However, stateful NATxy
(NAT44, NAT64, NAT66) solutions use the port numbers to identify
connections. The usage of pseudorandom port numbers causes different
problems depending on the direction.
* As for the private to public direction, pseudorandom source and
destination port numbers could be used, however, this approach
would be a denial of service attack against the stateful NATxy
gateway, because it would exhaust its connection tracking table.
To that end, let us see some calculations using the
recommendations of RFC 4814:
- The recommended source port range is: 1024-65535, thus its size
is: 64512.
- The recommended destination port range is: 1-49151, thus its
size is: 49151.
- The number of source and destination port number combinations
is: 3,170,829,312.
Lencse & Shima Expires 5 September 2022 [Page 3]
Internet-Draft Benchmarking Stateful Gateways March 2022
We note that section 12 of [RFC2544] also requires testing with
256 destination networks, which further increases the number of
connection tracking table entries.
* As for the public to private direction, the stateful DUT (Device
Under Test) would drop any packets that do not belong to an
existing connection, therefore, the direct usage of pseudorandom
port numbers from the above-mentioned ranges is not feasible.
3. Test Setup and Terminology
Our methodology works with any IP version. We use IPv4 in the Test
Setup shown in Figure 1 to facilitate its easy understanding based on
the well-known stateful NAT44 (also called NAPT: Network Address and
Port Translation) solution.
+--------------------------------------+
10.0.0.2 |Initiator Responder| 198.19.0.2
+-------------| Tester |<------------+
| private IPv4| [state table]| public IPv4 |
| +--------------------------------------+ |
| |
| +--------------------------------------+ |
| 10.0.0.1 | DUT: | 198.19.0.1 |
+------------>| Sateful NATxy gateway |-------------+
private IPv4| [connection tracking table] | public IPv4
+--------------------------------------+
Figure 1: Test Setup for benchmarking stateful NATxy gateways
As for transport layer protocol, [RFC2544] recommended testing with
UDP, and it was kept also in [RFC8219]. For the general
recommendation, we also keep UDP, thus the port numbers in the
following text are to be understood as UDP port numbers. We discuss
the limitation of this approach in Section 6.
We define the most important elements of our proposed benchmarking
system as follows.
* Connection tracking table: The stateful NATxy gateway uses a
connection tracking table to be able to perform the stateful
translation in the public to private direction. Its size, policy
and content are unknown for the Tester.
Lencse & Shima Expires 5 September 2022 [Page 4]
Internet-Draft Benchmarking Stateful Gateways March 2022
* Four tuple: The four numbers that identify a connection are source
IP address, source port number, destination IP address,
destination port number.
* State table: The Responder of the Tester extracts the four tuple
from each received test frame and stores it in its state table.
Recommendation is given for writing and reading order of the state
table in Section 4.8.
* Initiator: The port of the Tester that may initiate a connection
through the stateful DUT in the private to public direction.
Theoretically, it can use any source and destination port numbers
from the ranges recommended by [RFC4814]: if the used four tuple
does not belong to an existing connection, the DUT will register a
new connection into its connection tracking table.
* Responder: The port of the Tester that may not initiate a
connection through the stateful DUT in the public to private
direction. It may send only frames that belong to an existing
connection. To that end, it uses four tuples that have been
previously extracted from the received test frames and stored in
its state table.
* Preliminary test phase: Test frames are sent only by the Initiator
to the Responder through the DUT to fill both the connection
tracking table of the DUT and the state table of the Responder.
This is a newly introduced operation phase for stateful NATxy
benchmarking. The necessity of this phase is explained in
Section 4.2.
* Real test phase: The actual test (e.g. throughput, latency, etc.)
is performed in this phase after the completion of the preliminary
test phase. Test frames are sent as required (e.g. bidirectional
test or unidirectional test in any of the two directions).
4. Recommended Benchmarking Method
4.1. Restricted Port Number Ranges
The Initiator SHOULD use restricted ranges for source and destination
port numbers to avoid the denial of service attack like event against
the connection tracking table of the DUT described in Section 2. The
size of the source port number range SHOULD be larger (e.g. in the
order of a few times ten thousand), whereas the size of the
destination port number range SHOULD be smaller (may vary from a few
to several hundreds or thousands as needed). The rationale is that
source and destination port numbers that can be observed in the
Internet traffic are not symmetrical. Whereas source port numbers
Lencse & Shima Expires 5 September 2022 [Page 5]
Internet-Draft Benchmarking Stateful Gateways March 2022
may be random, there are a few very popular destination port numbers
(e.g. 443, 80, etc., see [IIR2020]) and others hardly occur. And we
have found that their role is also asymmetric in the Linux kernel
routing hash function [LEN2020].
The product of the sizes of the two ranges can be used as a
parameter. The performance of the stateful NATxy gateway MAY be
examined as a function of this parameter.
4.2. Preliminary Test Phase
The preliminary phase serves two purposes:
1. The connection tracking table of the DUT is filled. It is
important, because its maximum connection establishment rate may
be lower than its maximum frame forwarding rate (that is
throughput).
2. The state table of the Responder is filled with valid four
tuples. It is a precondition for the Responder to be able to
transmit frames that belong to connections exist in the
connection tracking table of the DUT.
Whereas the above two things are always necessary before the real
test phase, the preliminary phase can be used without the real test
phase. It is done so, when the maximum connection establishment rate
is measured (as described in Section 4.5).
A preliminary test phase MUST be performed before all tests performed
in the real test phase. In this phase, the following things happen:
1. The Initiator sends test frames to the Responder through the DUT
at a specific frame rate.
2. The DUT performs the stateful translation of the test frames and
it also stores the new combinations in its connection tracking
table.
3. The Responder receives the translated test frames and updates its
state table with the received four tuples. The responder
transmits no test frames during the preliminary phase.
When the preliminary test phase is performed in preparation to the
real test phase, the applied frame rate and the duration of the
preliminary phase SHOULD be carefully selected so that:
* The applied frame rate be safely lower than the maximum connection
establishment rate.
Lencse & Shima Expires 5 September 2022 [Page 6]
Internet-Draft Benchmarking Stateful Gateways March 2022
* Enough four tuples be stored in the state table of the Responder
so that it can generate frames with the proper distribution of the
four tuples.
Please refer to Section 4.4 for further conditions regarding timeout
and port number combinations.
4.3. Consideration of the Cases of Stateful Operation
We consider the most important Events that may happen during the
operation of a stateful NATxy gateway, and the Actions of the gateway
as follows.
1. EVENT: A packet not belonging to an existing connection arrives
in the private to public direction. ACTION: A new connection is
registered into the connection tracking table and the packet is
translated and forwarded.
2. EVENT: A packet not belonging to an existing connection arrives
in the public to private direction. ACTION: The packet is
discarded.
3. EVENT: A packet belonging to an existing connection arrives (in
any dicection). ACTION: The packet is translated and forwarded
and the timeout counter of the corresponding connection tracking
table entry is reset.
4. EVENT: A connection tracking table entry times out. ACTION: The
entry is deleted from the connection tracking table.
Due to "black box" testing, the Tester is not able to directly
examine (or delete) the entries of the connection tracking table.
But the entires can be and MUST be controlled by setting an
appropriate timeout value and carefully selecting the port numbers of
the packets (as described in Section 4.4) to be able to produce
meaningful and repeatable measurement results.
We aim to support the measurement of the following performance
characteristics of a stateful NATxy gateway:
1. maximum connection establishment rate
2. all "classic" performance metrics like throughput, frame loss
rate, latency, etc.
3. connection tear down rate.
Lencse & Shima Expires 5 September 2022 [Page 7]
Internet-Draft Benchmarking Stateful Gateways March 2022
4.4. Control of the Connection Tracking Table Entries
It is necessary to control the connection tracking table entries of
the DUT in order to achieve clear conditions for the measurements.
We can simply achieve the following two extreme situations:
1. All frames create a new entry in the connection tracking table of
the DUT and no old entries are deleted during the test. This is
required for measuring the maximum connection establishment rate.
2. No new entries are created in the connection tracking table of
the DUT and no old ones are deleted during the test. This is
ideal for the real test phase measurements, like throughput,
latency, etc.
From this point we use the following three assumptions:
1. A single source address destination address pair is used for all
tests. We make this assumption for simplicity. Of course, we
are aware that [RFC2544] requires testing also with 256 different
destination networks.
2. The connection tracking table of the stateful NATxy is large
enough to store all connections defined by the different source
port number destination port number combinations.
3. Each experiment is started with an empty connection tracking
table. (It can be ensured by deleting its content before the
experiment.)
The first extreme situation can be achieved by
* using all different source port number destination port number
combinations in the preliminary phase and
* setting the UDP timeout of the NATxy gateway to a value higher
than the length of the preliminary phase.
The second extreme situation can be achieved by
* using all different source port number destination port number
combinations in the preliminary phase and
* enumerating all the possible source port number destination port
number combinations in the preliminary phase and
Lencse & Shima Expires 5 September 2022 [Page 8]
Internet-Draft Benchmarking Stateful Gateways March 2022
* setting the UDP timeout of the NATxy gateway to a value higher
than the length of the preliminary phase plus the gap between the
two phases plus the length of the real test phase.
[RFC4814] REQUIRES pseudorandom port numbers, which we believe is a
good approximation of the distribution of the source port numbers a
NATxy gateway on the Internet may face with.
We note that pseudorandom all different source port number
destination port number combinations may be computing efficiently
generated by preparing a random permutation of the previously
enumerated all possible source port number destination port number
combinations using Dustenfeld's random shuffle algorithm [DUST1964].
This method also satisfies the criterion for the second case that all
possible source port number destination port number combinations must
be enumerated during the preliminary phase.
Important warning: in normal (non-NAT) router testing, the port
number selection algorithm, whether it is pseudo-random or enumerated
in increasing (or decreasing) order does not affect final results.
However, our experience with iptables shows that if the connection
tracking table is filled using port number enumeration in increasing
order, then the maximum connection establishment rate of iptables
degrades significantly compared to its performance using pseudorandom
port numbers [LEN2021].
The enumeration of the source port number destination port number
combinations in increasing or decreasing order (or in any other
specific order) MAY be used as an additional measurement.
4.5. Measurement of the Maximum Connection Establishment Rate
The maximum connection establishment rate is an important
characteristic of the stateful NATxy gateway and its determination is
necessary for the safe execution of the preliminary test phase
(without frame loss) before the real test phase.
The measurement procedure of the maximum connection establishment
rate is very similar to the throughput measurement procedure defined
in [RFC2544].
Lencse & Shima Expires 5 September 2022 [Page 9]
Internet-Draft Benchmarking Stateful Gateways March 2022
Procedure: The Initiator sends a specific number of test frames using
all different source port number destination port number combinations
at a specific rate through the DUT. The Responder counts the frames
that are successfully translated by the DUT. If the count of offered
frames is equal to the count of received frames, the rate of the
offered stream is raised and the test is rerun. If fewer frames are
received than were transmitted, the rate of the offered stream is
reduced and the test is rerun.
The maximum connection establishment rate is the fastest rate at
which the count of test frames successfully translated by the DUT is
equal to the number of test frames sent to it by the Initiator.
Notes:
1. In practice, we RECOMMEND the usage of binary search.
2. As for the successful translation, the Responder MAY (or SHOULD?)
check that the source IP address is different than the original
source IP address set by the Initiator.
4.6. Real Test Phase
As for the traffic direction, there are three possible cases during
the real test phase:
* bidirectional traffic: The Initiator sends test frames to the
Responder and the Responder sends test frames to the Initiator.
* unidirectional traffic from the Initiator to the Responder: The
Initiator sends test frames to the Responder but the Responder
does not send test frames to the Initiator.
* unidirectional traffic from the Responder to the Initiator: The
Responder sends test frames to the Initiator but the Initiator
does not send test frames to the Responder.
If the Initiator sends test frames, then it uses pseudorandom source
port numbers and destination port numbers from the restricted port
number ranges. The responder receives the test frames, updates its
state table and processes the test frames as required by the given
measurement procedure (e.g. only counts them for throughput test,
handles timestamps for latency or PDV tests, etc.).
Lencse & Shima Expires 5 September 2022 [Page 10]
Internet-Draft Benchmarking Stateful Gateways March 2022
If the Responder sends test frames, then it uses the four tuples from
its state table. The reading order of the state table may follow
different policies (discussed in Section 4.8). The Initiator
receives the test frames, and processes them as required by the given
measurement procedure.
As for the actual measurement procedures, we RECOMMEND to use the
updated ones from Section 7 of [RFC8219].
4.7. Measurement of the Connection Tear Down Rate
Connection tear down can cause significant load for the NATxy
gateway. The connection tear down performance can be measured as
follows:
1. Load a certain number of connections (N) into the connection
tracking table of the DUT (in the same way as done to measure the
maximum connection establishment rate).
2. Record TimestampA.
3. Delete the content of the connection tracking table of the DUT.
4. Record TimestampB.
The connection tear down rate can be computed as:
connection tear down rate = N / ( TimestampB - TimestampA)
The connection tear down rate SHOULD be measured for various
(important) values of N.
We assume that the content of the connection tracking table may be
deleted by an out-of-band control mechanism specific to the given
NATxy gateway implementation. (E.g. by removing the appropriate
kernel module under Linux.)
We are aware that the performance of removing the entire content of
the connection tracking table at one time may be different from
removing all the entries one by one.
4.8. Writing and Reading Order of the State Table
As for writing policy of the state table of the Responder, we
RECOMMEND round robin, because it ensures that its entries are
automatically kept fresh and consistent with that of the connection
tracking table of the DUT.
Lencse & Shima Expires 5 September 2022 [Page 11]
Internet-Draft Benchmarking Stateful Gateways March 2022
The Responder can read its state table in various orders, for
example:
* pseudorandom
* round robin
We RECOMMEND pseudorandom to follow the spirit of [RFC4814]. Round
robin may be used as a computationally cheaper alternative.
5. Implementation and Experience
The "stateful" branch of siitperf [SIITPERF] is an implementation of
this concept. It is documented in a paper currently under second
review [LEN2022].
Our experience with this methodology using siitperf for measuring the
scalability of the iptables stateful NAT44 and Jool stateful NAT64
implementations is described in
[I-D.lencse-v6ops-transition-scalability].
6. Limitations of using UDP as Transport Layer Protocol
Stateful NATxy solutions handle TCP and UDP differently, e.g.
iptables uses 30s timeout for UDP and 60s timeout for TCP. Thus
benchmarking results produced using UDP do not necessarily
characterize the performance of a NATxy gateway well enough, when
they are used for forwarding Internet traffic. As for the given
example, timeout values of the DUT may be adjusted, but it requires
extra consideration.
Other differences in handling UDP or TCP are also possible. Thus we
recommend that further investigations are to be performed in this
field.
As a mitigation of this problem, we recommend that testing with
protocols usig TCP (like HTTP and HTTPS) can be performed as
described in [I-D.ietf-bmwg-ngfw-performance]. This approach also
solves the potential problem of protocol helpers may be present in
the stateful DUT.
7. Acknowledgements
The authors would like to thank Al Morton, Sarah Banks, Edwin
Cordeiro, Lukasz Bromirski and Sandor Repas for their comments.
Lencse & Shima Expires 5 September 2022 [Page 12]
Internet-Draft Benchmarking Stateful Gateways March 2022
8. IANA Considerations
This document does not make any request to IANA.
9. Security Considerations
We have no further security considerations beyond that of [RFC8219].
Perhaps they should be cited here so that they be applied not only
for the benchmarking of IPv6 transition technologies, but also for
the benchmarking of stateful NATxy gateways.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2544] Bradner, S. and J. McQuaid, "Benchmarking Methodology for
Network Interconnect Devices", RFC 2544,
DOI 10.17487/RFC2544, March 1999,
<https://www.rfc-editor.org/info/rfc2544>.
[RFC4814] Newman, D. and T. Player, "Hash and Stuffing: Overlooked
Factors in Network Device Benchmarking", RFC 4814,
DOI 10.17487/RFC4814, March 2007,
<https://www.rfc-editor.org/info/rfc4814>.
[RFC5180] Popoviciu, C., Hamza, A., Van de Velde, G., and D.
Dugatkin, "IPv6 Benchmarking Methodology for Network
Interconnect Devices", RFC 5180, DOI 10.17487/RFC5180, May
2008, <https://www.rfc-editor.org/info/rfc5180>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8219] Georgescu, M., Pislaru, L., and G. Lencse, "Benchmarking
Methodology for IPv6 Transition Technologies", RFC 8219,
DOI 10.17487/RFC8219, August 2017,
<https://www.rfc-editor.org/info/rfc8219>.
10.2. Informative References
Lencse & Shima Expires 5 September 2022 [Page 13]
Internet-Draft Benchmarking Stateful Gateways March 2022
[DUST1964] Durstenfeld, R., "Algorithm 235: Random
permutation", Communications of the ACM, vol. 7, no. 7,
p.420., DOI 10.1145/364520.364540, July 1964,
<https://dl.acm.org/doi/10.1145/364520.364540>.
[I-D.ietf-bmwg-ngfw-performance]
Balarajah, B., Rossenhoevel, C., and B. Monkman,
"Benchmarking Methodology for Network Security Device
Performance", Work in Progress, Internet-Draft, draft-
ietf-bmwg-ngfw-performance-13, 12 January 2022,
<https://www.ietf.org/archive/id/draft-ietf-bmwg-ngfw-
performance-13.txt>.
[I-D.lencse-v6ops-transition-scalability]
Lencse, G., "Scalability of IPv6 Transition Technologies
for IPv4aaS", Work in Progress, Internet-Draft, draft-
lencse-v6ops-transition-scalability-01, 21 February 2022,
<https://www.ietf.org/archive/id/draft-lencse-v6ops-
transition-scalability-01.txt>.
[IIR2020] Kurahashi, T., Matsuzaki, Y., Sasaki, T., Saito, T., and
F. Tsutsuji, "Periodic observation report: Internet trends
as seen from IIJ infrastructure - 2020", Internet
Infrastructure Review, vol. 49, December 2020,
<https://www.iij.ad.jp/en/dev/iir/pdf/
iir_vol49_report_EN.pdf>.
[LEN2020] Lencse, G., "Adding RFC 4814 Random Port Feature to
Siitperf: Design, Implementation and Performance
Estimation", International Journal of Advances in
Telecommunications, Electrotechnics, Signals and Systems,
vol 9, no 3, pp. 18-26., DOI 10.11601/ijates.v9i3.291,
2020, <http://www.hit.bme.hu/~lencse/
publications/291-1113-1-PB.pdf>.
[LEN2021] Lencse, G., "Design and Implementation of a Software
Tester for Benchmarking Stateful NAT64 Gateways: Theory
and Practice of Extending Siitperf for Stateful
Tests", it was under review in Computer
Communications, then it was significantly rewritten,
2021, <http://www.hit.bme.hu/~lencse/publications/SFNAT64-
tester-for-review.pdf>.
Lencse & Shima Expires 5 September 2022 [Page 14]
Internet-Draft Benchmarking Stateful Gateways March 2022
[LEN2022] Lencse, G., "Design and Implementation of a Software
Tester for Benchmarking Stateful NAT64xy Gateways: Theory
and Practice of Extending Siitperf for Stateful
Tests", revised version, under second review in Computer
Communications, may be revised or removed without notice,
2022, <http://www.hit.bme.hu/~lencse/publications/SFNATxy-
tester-revised.pdf>.
[SIITPERF] Lencse, G., "Siitperf: An RFC 8219 compliant SIIT
(stateless NAT64) tester written in C++ using
DPDK", source code, available from GitHub, 2019-2022,
<https://github.com/lencsegabor/siitperf>.
Appendix A. Change Log
A.1. 00
Initial version.
A.2. 01
Updates based on the comments received on the BMWG mailing list and
minor corrections.
A.3. 02
Section 4.4 was completely re-written. As a consequence, the
occurrences of the now undefined "mostly different" source port
number destination port number combinations were deleted from
Section 4.5, too.
A.4. 03
Added Section 4.3 about the consideration of the cases of stateful
operation.
Consistency checking. Removal of some parts obsolated by the
previous re-writing of Section 4.4.
Added Section 4.7 about the method for measuring connection tear down
rate.
Updates for Section 5 about the implementation and experience.
Authors' Addresses
Lencse & Shima Expires 5 September 2022 [Page 15]
Internet-Draft Benchmarking Stateful Gateways March 2022
Gabor Lencse
Szechenyi Istvan University
Gyor
Egyetem ter 1.
H-9026
Hungary
Email: lencse@sze.hu
Keiichi Shima
IIJ Innovation Institute
Iidabashi Grand Bloom, 2-10-2 Fujimi, Tokyo
102-0071
Japan
Email: keiichi@iijlab.net
Lencse & Shima Expires 5 September 2022 [Page 16]