IKEv2 Link Maximum Atomic Packet and Packet Too Big Notification Extension

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶

This Internet-Draft will expire on 8 April 2024.¶

Copyright Notice

Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶

Table of Contents

1. Introduction

Reassembling fragments at the egress security gateway requires additional resources which under heavy load results in service degradations. Then, as detailed in [RFC4963], [RFC6864] or [RFC8900], fragmentation is considered fragile and not sufficiently robust at high data rates. Typically, the 16-bit IPv4 identification field is not large enough to prevent duplication making fragmentation not sufficiently robust at high data rates. In IPv6 the 32 byte identification field reduces such collisions.¶

Figure 1 depicts various fragmentation scenarios that can occur when Tunnel Transit Packets (TTP) are encapsulated over an IPsec tunnel. The IPsec packets exchanged between the ingress and the egress security gateway are designated as Tunnel Link Packet (TLP).¶

Source          Security             Security             Destination
or              Gateway              Gateway              or
Sender       (Ingress node)        (Egress node)          Receiver

+--+             +---+                 +---+              +---+
|  |  +  +  +    |   |  +  +  +  +  +  |   |  +  +  +  +  |   |
+--+  routers    +---+    routers      +---+  routers     +---+
                  <--------------------->
                            N
+---+---+----+                            +---+---+----+
|IPs|IPd|Data|  Tunnel Transit Packet     |IPs|IPd|Data|
+---+---+----+         (TTP)              +---+---+----+



1) No fragmentation

                +---+---+---+---+---+----+
                |IPi|IPe|ESP|IPs|IPd|Data| Tunnel Link Packet
                +---+---+---+---+---+----+       (TLP)

2) Mid-tunnel (performed by a router on N)
  (only for IPv4 DF=0  TLP)
                         +---+---+---+---+---+--+
                         |IPi|IPe|ESP|IPs|IPd|Da| (TLP)
                         +---+---+---+---+---+--+
                     +---+---+--+
                     |IPi|IPe|ta| (TLP)
                     +---+---+--+

3) Inner fragmentation (performed by the Ingress node)
  (only for IPv4 DF=0 TTP)

                +---+---+---+---+---+--+
                |IPi|IPe|ESP|IPs|IPd|Da| (TLP)
                +---+---+---+---+---+--+
            +---+---+---+---+---+--+
            |IPi|IPe|ESP|IPs|IPd|ta| (TLP)
            +---+---+---+---+---+--+

4) Outer fragmentation (performed by the Ingress node)
   (IPv4 or IPv6 TLP)
                +---+---+---+---+---+--+
                |IPi|IPe|ESP|IPs|IPd|Da| (TLP)
                +---+---+---+---+---+--+
            +---+---+--+
            |IPi|IPe|ta| (TLP)
            +---+---+--+

5) Source fragmentation
  (IPv6 or IPv4)
    +---+---+--+
    |IPs|IPd|Da|  (TTP)
    +---+---+--+
+---+---+--+
|IPs|IPd|ta|
+---+---+--+

Reassembling is performed by the egress node in two cases. Firstly when mid tunnel fragmentation happens (see 2) Figure 1) -- in which case the TLP header or outer header is using IPv4 with its Do not Fragment bit set to 0 (DF=0). Secondly when Outer fragmentation is performed by the ingress node (see 4 in Figure 1). The main difference between the two scenarios is that with Outer fragmentation, the ingress node is aware that the egress performs some reassembly operations. Note also that in both cases, reassembling the TLP in itself does not prevent the TTP to be processed by IPsec unless the reassembled TLP exceeds the effective MTU to receive (EMTU_R) - that is the maximum size of the IPsec protected packet that can be accepted by the egress node to perform the ESP encapsulation.¶

Figure 2 summarizes the various operations performed by the egress node according to the size of an IPsec encapsulated TTP. The optimal size of the TTP is the maximum TTP size that avoids fragmentation and the corresponding TTP size is designated as Tunnel maximum atomic packet (TMAP). The resulting IPsec encapsulated TTP (or LTP) is designated as Link maximum atomic packet (LMAP) LTP. The difference between the two sizes is related to the IPsec encapsulation overhead. LTP smaller than the LMAP will not generate any fragmentation. LTP larger than the LMAP, but smaller than the EMTU_R will be fragmented and reassembled by the egress node. The TTP will be transmitted. LTP (eventually reassembled) with a size greater than EMTU_R cannot be handled by the egress node and will not be transmitted. Note that in this case and unless specified explicitly the link considered is the physical link between the ingress and egress node.¶

          TMAP              TMTU
+---------+-------------------+--------------> TTP
|         |encap              |encap
|         |<--->|             |<--->|
| No frag. (1)  |  Fragmentation    |
|               |  (2) Mid-tunnel   |  Packet To Big
|               |  (4) Outer        |
+---------------+-------------------+--------> IPsec encapsulated TTP
              LMAP                EMTU_R

This document enables a egress node to inform the ingress node that:¶

• a received packet is fragmented (via an IKE LMAP notification)¶
• a packet received is too big to be processed by IPsec (via an IKE PTB notification)¶

As depicted in Figure 3, by supporting this extension, the ingress and egress node commit themselves in optimizing the processing of the IPsec tunnel and in limiting reassembly operation being performed at the egress node. More specifically, the ingress security gateway limits as much as possible the use of outer fragmentation and commits to set their TMTU value so that TTP are not fragmented/reassembled. In addition, for TTP with IPv4 addresses and DF=0, the ingress node commits to perform inner fragmentation to prevent reassembly at the egress node.¶

The mechanism is especially useful when the tunnel between the ingress and egress nodes is using IPv4 outer IP addresses with DF=0 as the fragmentation may occur while the ingress may not be aware of it.¶

The mechanisms enables also enable to inform the IPsec encapsulated TTP is too large and cannot be processed by IPsec. A LTP packet may be to big if it exceeds the LMTU or the EMTU_R. When one of these boundaries is exceeded, both are returned to the ingress node so, the ingress node can clearly understand why the packet has been dropped.¶

A packet may meet the LMTU requirement, but may not meet the EMTU_R requirement.
With IPv4 outer IP addresses with DF=0, the egress Security Gateway may receive a serie of fragments that individually do not exceed the MTU (and as such do not generate any LTP ICMP PTB) reassemble a fragmented IPsec encapsulated. That reassembled packet may exceed the size to be processed by IPsec. Similarly, even without fragmentation, the LTP MTU may exceed the capacity of the IPsec hardware in which case a IPsec encapsulated may not generate a LTP ICMP PTB but may not be further processed. Even though MTU values may be sent via a LTP ICMP PTB message, we do envision that the communication of the LMTU via an IKE notification may provide some advantages over simply relying on LTP ICMP messages. However, please note these advantages are only secondary and only mentioned here as an information. At first the IKE channel is authenticated channel that ensures the LMTU is 1) received by the ingress Security Gateway, 2) is integrity protected and 3) can be appropriately bound to the corresponding SA. An ICMP PTB message when sent from the egress Security Gateway is not protected and when UDP encapsulation is used (see {sec-sec}) and may not carry the SPI of the IPsec encapsulated TTP (see {sec-df1}). However, these advantages are only provided by the egress interface and so that mechanism cannot be used by any other node, and so cannot be used for PMTU discovery. Secondly, the IKE notification MAY be sent together with the TTP ICMP PTB sent by the router. This may improve the network latency and optimizes the use of the security gateway resources, especially when the SA has been set for multiple Sources. In fact the TTP ICMP PTB sent by the egress router is sent specifically to the sending source, and so one can expect the ICMP PTB being sent to every source. By sending the notification via IKE, the information is received by the ingress Security Gateway which can take action globally for all Sources associated to the SA. This prevents the large packet greater than the MTU to be encrypted and sent to the egress router for nothing.¶

This document does not discuss these optimizations.¶

Source          Security             Security             Destination
or              Gateway              Gateway              or
Sender       (Ingress node)        (Egress node)          Receiver

+--+             +---+                 +---+              +---+
|  |  +  +  +    |   |  +  +  +  +  +  |   |  +  +  +  +  |   |
+--+  routers    +---+    routers      +---+  routers     +---+
                  <--------------------->
                            N
1) Mid-tunnel (performed by a router on N)
  (only for IPv4 DF=0  TLP)
                         +---+---+---+---+---+--+
                         |IPi|IPe|ESP|IPs|IPd|Da| (TLP)
                         +---+---+---+---+---+--+
                     +---+---+--+
                     |IPi|IPe|ta| (TLP)
                     +---+---+--+

2) Egress node detects fragmentation
     - a) it collects IPVersion the IP version of the first fragment
         as well as FragLen, the fragment length
     - b1) If all segments can be reassembled and the reassembled
         packet is properly decrypted a Link Maximum Atomic
         Packet Notification (LMAP) is sent on the IKEv2 channel.
          [IKEv2]
          <---  N( LMAP [ IPVersion, FragLen] )
     - b2) If the packet is too big and cannot be fully processed, an
         additional Packet Too Big Notification (PTB) that specifies
         the Link MTU (LMTU) of the router component of the egress
         node (on network N) as well as the effective MTU to receive
         (EMTU_R). Both are configuration parameters.
         An ICMP PTB message may also be sent by the egress node.
         This is considered as independent from the fact that the
         egress Security Gateway is sending an IKE PTB or not.
         Note that this ICMP may not contain even the SPI, and so is
         likely to not carry sufficient information to the ingress node,
         so any action be taken.
          [IKEv2]
          <---  N( LMAP [ IPVersion, FragLen] )
                N( PTB [LMTU, EMTU_R]
          [ESP]
          <--- ESP( ICMP PTB )

3) Upon receiving the LMAP or optionally the ingress node
  a) Update the TMTU so that the Source performs source fragmentation
    with TTP packets that are not fragmented.
  Source fragmentation
  (IPv6 or IPv4)
    +---+---+--+
    |IPs|IPd|Da|  (TTP)
    +---+---+--+
+---+---+--+
|IPs|IPd|ta|
+---+---+--+


  b) Performs inner fragmentation TTP packets that exceeds the TMTU
    and will generate some fragments.
  Inner fragmentation (performed by the Ingress node)
  (only for IPv4 DF=0 TTP)

                +---+---+---+---+---+--+
                |IPi|IPe|ESP|IPs|IPd|Da| (TLP)
                +---+---+---+---+---+--+
            +---+---+---+---+---+--+
            |IPi|IPe|ESP|IPs|IPd|ta| (TLP)
            +---+---+---+---+---+--+

In both cases the egress node does not proceed to reassembly operations
                                                +---+---+--+
                                                |IPs|IPd|Da|  (TTP)
                                                +---+---+--+
                                            +---+---+--+
                                            |IPs|IPd|ta|
                                            +---+---+--+

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|   Type = 3    |   Code = 4    |           Checksum            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|           unused = 0          |         Next-Hop MTU          |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|      Internet Header + 64 bits of Original Datagram Data      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

2. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶

Tunnel, Ingress node, Egress node, Ingress Interface, Egress interface, Tunnel Transit Packets (TTP), Tunnel Link Packet (TLP), Link MTU (LMTU), Tunnel MTU (TMTU), Tunnel maximum atomic packet (TMAP), effective MTU to receive (EMTU_R) are defined in [I-D.ietf-intarea-tunnels].¶

3. Link Maximum Atomic Packet and Packet Too Big Support Negotiation

During an IKEv2 negotiation, the initiator and the responder indicate their support for the Link Maximum Atomic Packet and Packet Too Big Extension by exchanging the LMAP_AND_PTB_SUPPORTED notifications. This notification MUST be sent in the IKE_AUTH exchange (in case of multiple IKE_AUTH exchanges - in the first IKE_AUTH message from initiator and in the last IKE_AUTH message from responder). If both the initiator and the responder send this notification during the IKE_AUTH exchange, peers may notify each other with an IPv4 Link Maximum Atomic Packet Notification when fragmentation is observed. Upon receiving such notifications, the peers may take the necessary actions to prevent such fragmentation to occur.¶

Initiator                         Responder
-------------------------------------------------------------------
HDR, SA, KEi, Ni -->
                         <-- HDR, SA, KEr, Nr
HDR, SK {IDi, AUTH,
     SA, TSi, TSr,
     N(LMAP_AND_PTB_SUPPORTED)} -->
                         <-- HDR, SK {IDr, AUTH,
                             SA, TSi, TSr,
                             N(LMAP_AND_PTB_SUPPORTED)}

4. Sending a Link Maximum Atomic Packet Notification

The egress security gateway detects fragmentation occurred when it receives an initial fragment; e.g. with the Flags' More Fragment Bit set to 1 and the Fragment Offset set to 0. Upon receiving such a packet, the egress node determines the IP version (IPVersion) and the fragment length FragLen). For an IPv4 packet, FragLen is the Total Length field (see [RFC0791]). For an IPv6 packet FragLen is the Payload Length (see [RFC8200], Section 3. Note that these values have different meanings as with an IPv6 fragment, FragLen does not include the IPv6 header but only the payload.¶

The egress node sends the LMAP notification payload that contains IPVersion and FragLen.¶

The egress node SHOULD send a maximum of one LMAP notification per (reassembled) received packet. However, since this extension is especially expected on nodes dealing with high traffic rates, the notification is expected to be sent at reasonable rates per Security Associations. More specifically, the use of the IKEv2 provides a reliable channel which makes sending redundant notifications unnecessary. Then, the notification rate needs to account for the time the egress node adjusts the TMTU, and that TMTU remains implemented. More details are provided in Section 10.¶

Egress Security Gateway                 Ingress Security Gateway
-------------------------------------------------------------------
HDR SK { N(LMAP)} -->

5. Receiving a Link Maximum Atomic Packet Notification

Upon receiving a LMAP notification, the ingress node derives the tunnel MAP (TMAP) from the Link MAP (LMAP) derived by the FragLen and IPVersion.¶

if IPVersion is 4:
  LMAP = FragLen
elif IPVersion is 6:
  LMAP = FragLen + 40
TMAP = LMAP - outer IP header - encapsulation overhead

where

¶

IPVersion:

The IP version of the fragment provided by the LMAP notification (see Section 4).¶

FragLen:

The Fragment length provided by the LMAP notification (see Section 4).¶

LMAP:

For an IPv4 packet, LMAP is directly provided by the fragment length of the LMAP Notification. For an IPv6 packet, LMAP needs to adds the IPv6 Header length (40 bytes) to the fragment length of the LMAP Notification.¶

outer IP header:

The IP header of the LTP encapsulation overhead: contains the ESP header, the ESP Trailer including the variable Pad field. When the padding is minimizing the Pad Len, the encapsulation header is set to 14 (+ the size of the ICV). The overhead SHOULD also estimate IP options or IP extensions.¶

The ingress security gateway SHOULD propagate the TMAP as the tunnel MTU back to the Source so the size of future TTP packets does not exceed the TMAP - eventually performing source fragmentation. To do so, the ingress node sets the LMTU to TMAP for all traffic designated by the SA. In this case the LMTU is the MTU associated with the link of the router interface of the ingress node that faces the Source's network. Upon receiving a TLP larger than the TMAP, the packet is discarded and an ICMP PTB message is returned to the Source which then performs Source Fragmentation (5) (See Section 8.2.1. of [RFC4301]). It is worth mentioning that only future packets will be impacted, and not those causing fragmentation.¶

When the TLP is an IPv4 packet with DF=0, the ingress node SHOULD perform Source Fragmentation of the TTP, also represented as Inner Fragmentation (3), sending chunks that do not exceed TMAP.¶

Figure 11 in Section 4.2.2 of [I-D.ietf-intarea-tunnels] with tunnel MTU set to TMAP achieves both recommendations, while Figure 12 in Section 4.2.2 describes the inner fragmentation.¶

6. Sending a Packet Too Big Notification

A packet can be rejected because the size of the LTP exceeds the LMTU (of the router component) or when the (reassembled) LTP exceeds the EMTU_R (of the interface component) and so IPsec decapsulation cannot be done.¶

When the LTP size exceeds the EMTU_R, the egress node SHOULD send a Packet Too Big (PTB) notification that includes the EMTU_R and the LMTU. In addition, if the packet results from a reassembly operation, the egress node MUST send a LMAP notification with the LMAP. If the packet does not result from a reassembly operation, the egress node MUST NOT send a LMAP notification.¶

Egress Security Gateway                 Ingress Security Gateway
-------------------------------------------------------------------
HDR SK { N(PTB) } -->

7. Receiving a Packet Too Big Notification

Upon receiving a PTB notification, the egress node computes the Tunnel MTU (TMTU) as follows:¶

TMTU = EMTU_R - outer IP header - encapsulation overhead
if LMAP notification is not received:
  TMAP is derived from the LMAP notification
else:
  TMAP = LMTU - outer IP header - encapsulation overhead
TMAP = min( TMAP, TMTU )

with the same notation as in Figure 5:

¶

EMTU_R:

The value provided in the PTB notification related to the MTU associated to the egress interface (see Section 6)¶

LMTU :

The value provided in the PTB notification related to the LMTU associated to the egress router (see Section 6)¶

The ingress node SHOULD proceed with TMAP as described in Section 5.¶

The ingress node MUST ensure the size of the TTP do not exceed the computed TMTU and MUST ensure the size of the LTP do not exceed the LMTU provided in the PTB notification.¶

8. Payload Description

Figure 7 illustrates the Notify Payload packet format as described in Section 3.10 of [RFC7296] with a 4 bytes path allowed MTU value as notification data. This format is used for both the LMAP_AND_PTB_SUPPORTED, LMAP and PTB notifications.¶

1                   2                   3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Payload  |C|  RESERVED   |         Payload Length        |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|  Protocol ID  |   SPI Size    |      Notify Message Type      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
~                       Notification Data                       ~
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The fields Next Payload, Critical Bit, RESERVED and Payload Length are defined in [RFC7296]. Specific fields defined in this document are:¶

Protocol ID (1 octet):

set to zero.¶

SPI Size (1 octet):

set to zero.¶

Notify Message Type (2 octets):

Specifies the type of notification message. It is set to TBD1 for the LMAP_AND_PTB_SUPPORTED notification, TBD2 for the LMAP notification and TBD3 for the PTB notification.¶

Notification Data:

Specifies the data associated to the notification message. It is empty for the LMAP_AND_PTB_SUPPORTED notification or a 4 octets that contains the MTU value for the LMAP and PTB notification - as represented in Figure 8 and Figure 9.¶

 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|IPVers |       Reserved        |          FragLen              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

with:¶

IPVersion (4 bits):

The IPversion of the received packet¶

Reserved:

Reserved bytes MUST be set by the egress node to zero and MUST be ignored by the ingress node.¶

FragLen (2 bytes):

The FragLen value (see Section 4)¶

 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                         LMTU                                  |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                        EMTU_R                                 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

with:¶

LMTU (4 bytes):

The LMTU of the egress router¶

EMTU_R (4 bytes):

The EMTU_R of the egress interface¶

9. IANA Considerations

IANA is requested to allocate two values in the "IKEv2 Notify Message Types - Status Types" registry (available at https://www.iana.org/assignments/ikev2-parameters/ikev2-parameters.xhtml#ikev2-parameters-16) with the following definition:¶

+=======+================================+
| Value | NOTIFY MESSAGES - STATUS TYPES |
+=======+================================+
| TBD1  | LMAP_AND_SUPPORTED             |
| TBD2  | LMAP                           |
| TBD3  | PTB                            |
+-------+--------------------------------+

10. Security Considerations

This document defines an IKEv2 extension to enable an egress node to notify an ingress node that fragmentation is happening as well as the observed fragment length. In addition, the extension also enables an egress node to notify an ingress node that a packet too big has been discarded, together with some complementary information to appropriately update the MTU.¶

These pieces of information are transferred over the authenticated IKEv2 channel which ensures the origin of the message. Assuming the egress node is trusted, the ingress node can trust what is being reported effectively observed (like fragmentation is happening, the observed fragment length, a packet too big has been received) by the egress node and that some information are effectively accurate such as the egress LMTU and EMTU_R. When fragmentation happens and a LMAP notification is being sent, the egress node MUST send the notification once the reassembled packet has been decapsulated. This ensures that fragmentation has been performed over an authenticated TLP and ensures the TLP has not been forged by any attacker. With IPv6, only outer fragmentation is permitted so, the ingress node can validate the provided information. However, sending the notification after the IPsec decapsulation enables the egress node to detect potential injection attacks and prevent sending an unnecessary notification, that may be part of a DDoS attack targeting the ingress node itself. With IPv4 an attacker could set the DF=0 which would allow any mid tunnel fragmentation. IPsec (ESP or AH) does not cover the DF flag, so the egress cannot trust the fragment length observed has not been forged, and the security considerations related to MTU discovery [RFC0791], [RFC8900], [RFC4963], [RFC6864], [RFC1191] apply here. Note that information carried by the LMAP notification is never carried by ICMP, and all LMAP may share with ICMP is that this information will be used to update the MTU.¶

The egress node may not be able to decrypt the encrypted TTP packet if the full encrypted TTP cannot be built. One possibility is that too many fragments are being sent over a too long period of time (slowloris-like attacks) (see [RFC8900], Section 3.7). Another possibility is that one fragment exceeds the LMTU or that the reassembled (unverified) encrypted TTP exceeds the EMTU_R. In both cases, a PTB notification SHOULD be sent and if fragmentation is observed a LMAP MUST be sent together with the PTB notification. Information carried by the PTB (LMTU and EMTU_R) can be trusted. Without this extension this information would have been carried by ICMP. In many deployments, the ICMP channel may be unprotected and ICMP packets may be discarded by firewalls and never reach the egress node. In addition, the description provided by [I-D.ietf-intarea-tunnels] tends to indicate that the ICMP channel remains between the router components of the ingress and egress nodes and as such are not provided to the interfaces component. Finally, as detailed in Section 1.3 an ICMP PTB message contains a portion of the encrypted ESP packet, which may not sufficient to deduce the SPI and associated traffic selectors, and as such prevent the ingress node to identify the traffic flow that generates the fragmentation. In any case, this results in the information not being available to take the appropriate action. Sending the PTB notification over ICMP solves these issues and eases the correlation with the LMAP notification. In terms of trust, when sufficient information may be sent both on the IKEv2 channel and via a protected ICMP PTB message, the use of the PTB notification achieves similar trust as the one observed with an ICMP PTB message sent over an IPsec protected channel. For that reason, the ICMP messages SHOULD be protected by IPsec. The use of two different paths may provide some additional reliability as the same information is taking two different paths and that IKEv2 windows ensures the the information is received - as opposed to the (encrypted) ICMP message that can be dropped. However, information carried by the LMAP notification cannot be trusted and similar security considerations related to MTU discovery [RFC0791], [RFC8900], [RFC4963], [RFC6864], [RFC1191] apply here.¶

During high packet rates, this notification for each of these packets is likely to be used by an attacker to trigger a DDoS attack to both egress and ingress nodes. As a result, the egress node SHOULD be able to configure the maximum rate at which the notifications are sent. This includes the ability to indicate that LMAP notifications (without PTB) are not sent when the outer IP addresses are of version IPv6. The reasoning is that with IPv6, the egress node observes outer fragmentation, in which case the ingress node is already aware of it. In addition, an egress node SHOULD be able to configure a threshold for number of alerts per SAs before a notification is sent, a rate limit per SA.¶

11. Acknowledgements

The authors would like to thank Magnus Westerlund, Paul Wouters, Joe Touch, Tero Kivinen for his reviews and valuable comments and suggestions.¶

Authors' Addresses