Network Working Group A. Melnikov
Internet-Draft Isode Ltd
Intended status: Standards Track K. Carlberg
Expires: December 13, 2012 G11
June 11, 2012
Simple Mail Transfer Protocol extension for Message Transfer Priorities
draft-melnikov-smtp-priority-18
Abstract
This memo defines an extension to the SMTP (Simple Mail Transfer
Protocol) service whereby messages are given a label to indicate
preferential handling, to enable mail handling nodes to take this
into account for onward processing.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 13, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Melnikov & Carlberg Expires December 13, 2012 [Page 1]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions Used in This Document . . . . . . . . . . . . . . 4
3. Definition of the Priority SMTP Extension . . . . . . . . . . 4
4. Handling of messages received via SMTP . . . . . . . . . . . . 5
4.1. Handling of the MT-PRIORITY parameter by the receiving
SMTP server . . . . . . . . . . . . . . . . . . . . . . . 5
4.2. Relay of messages to other conforming SMTP servers . . . . 6
4.3. Relay of messages to non-conforming SMTP servers . . . . . 6
4.4. Mailing lists and Aliases . . . . . . . . . . . . . . . . 7
4.5. Gatewaying a message into a foreign environment . . . . . 7
4.6. Interaction with DSN SMTP Extension . . . . . . . . . . . 7
5. The Priority Service Extension . . . . . . . . . . . . . . . . 7
5.1. Expedited Transfer . . . . . . . . . . . . . . . . . . . . 9
5.2. Timely Delivery . . . . . . . . . . . . . . . . . . . . . 9
6. Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. Example . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8. Deployment Considerations . . . . . . . . . . . . . . . . . . 11
8.1. Multiple MX records . . . . . . . . . . . . . . . . . . . 11
8.2. Consistent priority handling policy . . . . . . . . . . . 11
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
10. Security Considerations . . . . . . . . . . . . . . . . . . . 14
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11.1. Normative References . . . . . . . . . . . . . . . . . . . 14
11.2. Informative References . . . . . . . . . . . . . . . . . . 15
Appendix A. Mapping of MT-PRIORITY parameter values for
Military Messaging . . . . . . . . . . . . . . . . . 16
Appendix B. Mapping of MT-PRIORITY parameter values for MIXER . . 17
Appendix C. Mapping of National Security / Emergency
Preparedness (NS/EP) Values . . . . . . . . . . . . . 17
Appendix D. Possible implementation strategies . . . . . . . . . 18
D.1. Probability . . . . . . . . . . . . . . . . . . . . . . . 18
D.2. Preemption of sessions or transactions . . . . . . . . . . 19
D.3. Resource Allocation Models . . . . . . . . . . . . . . . . 19
Appendix E. Background on Design Choices . . . . . . . . . . . . 20
Appendix F. Acknowledgements . . . . . . . . . . . . . . . . . . 20
Melnikov & Carlberg Expires December 13, 2012 [Page 2]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
1. Introduction
Where resources for switching or transfer of messages are constrained
(e.g., bandwidth, round trip time, transition storage or processing
capability) it is desirable to give preferential handling to some
messages over others, according to their labeled priority. This is
particularly important during emergencies for first responders and
for environments such as military messaging, where messages have high
operational significance, and the consequences of extraneous delay
can be significant.
In order for an SMTP receiver to be able to relay higher priority
messages first, there needs to be a mechanism to communicate (during
both Message Submission [RFC6409] and Message Transfer [RFC5321]) the
priority of each message. This specification defines this mechanism
by specification of an SMTP [RFC5321] extension.
In order to permit end-to-end use of this extension across email
infrastructure that does not support it, a companion tunneling
mechanism is defined in [PRIORITY-TUNNELING] through use of a new
message header field [RFC5322].
This extension provides services to some classes of users in networks
with limited available bandwidth or long round trip times, when the
actual message transfer over the network can create a significant
portion of the overall message delivery time from a sender to a
recipient, for example over a sattelite or high frequency radio link.
It is also useful in case of a Mail Transfer Agent (MTA) queue
build-up due to the rate of incoming messages being higher than the
rate of outgoing messages. When neither of the two conditions
mentioned above is true, the use of the MT-PRIORITY SMTP extension
will not result in a better SMTP service to any user. Also note that
while this SMTP extension can help in improving delivery speed for
higher priority messages, it does not provide any sort of guarantees
that for two given messages with priorities M and N (M > N) submitted
simultaneously the message with priority M will arrive earlier than
the message with priority N. I.e. this extension calls for best
effort to provide preferential processing.
Besides the actions taken at the application level it can thus be
important to deploy priority or precedence mechanisms offered by the
network itself to ensure timely delivery of the emails. Examples
would be the use of DiffServ [RFC2474], RSVP [RFC2205] and the work-
in-progress effort extension to RSVP that prioritizes reservations.
Melnikov & Carlberg Expires December 13, 2012 [Page 3]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119] when they
appear in ALL CAPS. These words also appear in this document in
lower case as plain English words, absent their normative meanings.
The formal syntax use the Augmented Backus-Naur Form (ABNF) [RFC5234]
notation including the core rules defined in Appendix B of RFC 5234
[RFC5234].
In examples, "C:" and "S:" indicate lines sent by the client and
server respectively. Line breaks that do not start with a new "C:"
or "S:" exist for editorial reasons and are not a part of the
protocol.
This document uses the term "priority" specifically in relation to
the internal treatment of a message by the server: messages with
higher priorities may be given expedited handling, and those with
lower priorities may be handled only as resources become available.
3. Definition of the Priority SMTP Extension
The Priority SMTP service extension is defined as follows:
1. The textual name of this extension is "Priority Message
Handling".
2. The EHLO keyword value associated with this extension is "MT-
PRIORITY".
3. The EHLO keyword has no parameters. Parameters are reserved for
possible future extensions and MUST be ignored by clients that
don't understand them.
4. No additional SMTP verbs are defined by this extension.
5. One optional parameter ("MT-PRIORITY") is added to the MAIL FROM
command. The value associated with this parameter is a decimal
integer number from -9 to 9 (inclusive) indicating the priority
of the email message (See Appendix E for more details on why this
range was selected). The syntax of the MT-PRIORITY parameter is
described by the <priority-value> ABNF non-terminal defined in
Section 6. Higher numbers mean higher priority.
6. The maximum length of a MAIL FROM command line is increased by 15
octets by the possible addition of a space, the MT-PRIORITY
Melnikov & Carlberg Expires December 13, 2012 [Page 4]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
keyword and value.
7. The MT-PRIORITY extension is valid for the submission service
[RFC6409] and LMTP [RFC2033].
4. Handling of messages received via SMTP
This section describes how a conforming SMTP server should handle any
messages received via SMTP.
4.1. Handling of the MT-PRIORITY parameter by the receiving SMTP server
The following rules apply to SMTP transactions in a server that
supports the MT-PRIORITY parameter:
1. If any of the associated <esmtp-value>s (as defined in Section
4.1.2 of [RFC5321]) are not syntactically valid, or if there is
more than one MT-PRIORITY parameter in a particular MAIL FROM
command, the server MUST return an error, for example "501 syntax
error in parameter" (with 5.5.2 Enhanced Status Code [RFC2034]
[RFC5248]).
2. When inserting a Received header field as specified in Section
4.4 of [RFC5321], the compliant MTA/MSA SHOULD include the
"PRIORITY" clause whose syntax is specified in Section 6.
3. If the sending SMTP client specified the MT-PRIORITY parameter to
the MAIL FROM command, then the value of this parameter is the
message priority.
4. If no priority has been determined by the above, the server may
use its normal policies to set the message's priority. By
default, each message has priority 0.
The SMTP server MUST NOT allow "upgraded" (positive) priorities from
untrusted (e.g. unauthenticated) or insufficiently trusted sources.
(One example of an "insufficiently trusted source" might be an SMTP
sender which authenticated using SMTP AUTH, but which is not
explicitly authorized to use the SMTP MT-PRIORITY service.) The
server MAY, however, allow an untrusted source to lower its own
message's priorities -- consider, for example, an email marketer that
voluntarily sends its marketing messages at a negative priority.
The SMTP server MAY also alter the message priority (to lower or to
raise it) in order to enforce some other site policy. For example an
MSA might have a mapping table that assigns priorities to messages
based on authentication credentials.
Melnikov & Carlberg Expires December 13, 2012 [Page 5]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
If the SMTP server lowers the priority of a message, it SHOULD use
the X.7.TBD3 Enhanced Status Code [RFC2034] .
Alternatively an SMTP server, which is an MSA, MAY reject a message
based on the determined priority. In such cases, the MSA SHOULD use
450 or 550 reply code. The corresponding Enhanced Status Code MUST
be X.7.TBD1 [RFC2034] if the determined priority level is below the
lowest priority currently acceptable for the receiving SMTP server.
Note that this condition might be temporary. In some environments,
operational policies might permit periods of operation that relay
only higher priority messages and reject lower priority ones. Such
handling choices need to be specified for that operational
environment.
4.2. Relay of messages to other conforming SMTP servers
The following rules govern the behavior of a conforming MTA (in the
role of an SMTP client), when relaying a message which was received
via the SMTP protocol, to an SMTP/LMTP server that supports the MT-
PRIORITY SMTP extension:
1. A MT-PRIORITY parameter with the value determined by the
procedure from Section 4.1 MUST appear in the MAIL FROM command
issued when the message is relayed to an MTA/MDA which also
supports the MT-PRIORITY extension. (Note that due to site
policy this value might be different from the value received from
the SMTP client. See Section 4.1 for details. Also note that
this value might be different than the priority level at which
the MTA actually handles the request, due to the rounding
described in Section 5.)
2. Further processing of the MT-PRIORITY parameter is described in
Section 5.
4.3. Relay of messages to non-conforming SMTP servers
The following rules govern the behavior of a conforming MTA (in the
role of an SMTP client), when relaying a message which was received
via the SMTP protocol, to an SMTP server that does not support the
MT-PRIORITY SMTP extension:
1. The relaying MTA MUST NOT use the MT-PRIORITY parameter in the
MAIL FROM command issued when relaying the message.
Melnikov & Carlberg Expires December 13, 2012 [Page 6]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
4.4. Mailing lists and Aliases
Several types of mechanisms exist to redirect or forward messages to
alternative or multiple addresses [RFC5598]. Examples for this are
aliases and mailing lists [RFC5321].
If a message is subject to such processing, the Mediator node
(Section 2.1 of [RFC5598]), SHOULD retain the MT-PRIORITY parameter
value for all expanded and/or translated addresses.
4.5. Gatewaying a message into a foreign environment
The following rules govern the behavior of a conforming MTA, when
gatewaying a message that was received via the SMTP protocol, into a
foreign (non-SMTP) environment:
1. If the destination environment is unable to provide an equivalent
of the MT-PRIORITY parameter, the conforming MTA SHOULD behave as
if it is relaying to a non-conformant SMTP server (Section 4.3).
2. If the destination environment is capable of providing an
equivalent of the MT-PRIORITY parameter, the conforming MTA
SHOULD behave as if it is relaying to a conformant SMTP server
(Section 4.2), converting the MT-PRIORITY value to the equivalent
in the destination environment.
4.6. Interaction with DSN SMTP Extension
An MTA which also conforms to [RFC3461] that needs to generate a
delivery report (whether for successful delivery or delayed/failed
delivery) for a message it is processing SHOULD use the priority
value of the message as the priority of the generated delivery
report.
For delivery reports received by an MTA, processing rules specified
in Section 4.1 apply. But note that while it might be tempting to
handle all delivery reports (a.k.a. DSNs) at their stated priority,
under the assumption that failure notices need to get through quickly
in some situations, but such a policy creates an exposure to fake-DSN
attacks if sources of DSNs can't be reliably established.
5. The Priority Service Extension
The priorities of messages affect the order the messages are
transferred from the client to the server. This is largely
independent from the order in which they were originally received by
the server.
Melnikov & Carlberg Expires December 13, 2012 [Page 7]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
A message priority is a decimal integer in the range from -9 to 9
(inclusive). SMTP servers compliant with this specification are not
required to support all 19 distinct priority levels (i.e. to treat
each priority value as a separate priority), but they MUST implement
at least the following 6 distinct priority levels: -4, -2, 0, 2, 4,
9. I.e. an implementation that only supports the 6 priority levels
will internally round up a syntactically valid level that isn't
supported to the next higher supported number. For example, such an
implementation will treat priority values below and including -4 as
priority -4, priority -3 as priority -2, and all priorities starting
from 5 are treated as priority 9. An SMTP server MAY support more
than 6 different priority levels. Decision about which levels to
support in addition to the 6 mentioned above is a local matter. (See
Section 8.2 for implementation/deployment considerations related to
priority assignment policy.)
Irrespectively of the number of distinct priority levels supported by
the SMTP server, when relaying the message to the next hop or
delivering it over LMTP, the SMTP server MUST communicate the
priority value as determined in Section 4.1.
Note: 19 possible priority levels are defined by this specification
for extensibility. For example, a particular implementation or
deployment environment might need to provide finer-grained control
over message transfer priorities. In such a case, a server
implementation might need an extra priority level beyond the 6 levels
defined above. See Appendix E for more details on why the range from
-9 to 9 was selected.
Some SMTP servers MAY impose additional maximum message size
constraints for different message transfer priorities, for example
messages with priority 6 might not be larger than 4 Kb. If an SMTP
server chooses to reject a message because it is too big for the
determined priority, it SHOULD use 552 reply codes, together with the
X.3.TBD2 Enhanced Status Code [RFC2034].
Implementation Note: If the SMTP server also supports the SMTP SIZE
extension [RFC1870] then an SMTP client can use both SIZE= and MT-
PRIORITY= parameters on the MAIL FROM command. This allows the
server to perform early rejection of a message in case the message
size is too big for the specified priority, thus avoiding wasting
bandwidth by transferring the message first and then rejecting it due
to its size.
The Priority Service Extension can be combined with DELIVERBY
[RFC2852] SMTP service extension, however there is no requirement
that both extensions are always implemented together.
Melnikov & Carlberg Expires December 13, 2012 [Page 8]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
5.1. Expedited Transfer
The main service provided by the Priority Message Handling SMTP
Service Extension is expedited transfer of emails with a higher
priority. Therefore an SMTP client that has more than one email to
send at a given time sends those with a higher priority before those
with a lower one. Additionally, the retry interval and/or default
timeout before non-delivery report is generated MAY be lower (more
aggressive) for messages of higher priority. Lower retry intervals/
default timeouts are controlled by the local MTA policy.
Note that as this SMTP extension requires some sort of trust
relationship between a sender and a receiver and thus some form of
authentication (whether using SMTP AUTH, TLS, IP address whitelist,
etc.), so senders using this SMTP extension will not be subject to
greylisting [GREYLISTING], unless they are unauthorized to use this
SMTP extension, due to an explicit policy decision or a
misconfiguration error.
In order to make implementations of this extension easier, this SMTP
extension only allows a single priority for all recipients of the
same message.
Within a priority level, the MTA uses its normal algorithm (the
algorithm used in absence of this SMTP extension) for ordering for
the messages.
Two possible ways of implementing expedited transfer are described in
more details in Appendix D. Note that these sections don't describe
all details and pitfalls for each implementation strategy.
5.2. Timely Delivery
An important constraint (usually associated with higher priority
levels) is that messages with high priority have some delivery time
constraints. In some cases, higher priorities mean a shorter maximum
time allowed for delivery.
Unextended SMTP does not offer a service for timely delivery, i.e.
"deliver this message within X seconds from submission" service. The
"Deliver By SMTP Service Extension" (DELIVERBY Extension) defined in
[RFC2852] is an example of an SMTP extension providing a service that
can be used to implement timely delivery. Note that SMTP DELIVERBY
and SMTP MT-PRIORITY extensions are complimentary and can be used
together (assuming the SMTP server they are talking to advertises
support for both). However note that use of the DELIVERBY extension
alone does not guarantee any priority processing. If the client is
using both SMTP DELIVERBY and SMTP MT-PRIORITY at the same time,
Melnikov & Carlberg Expires December 13, 2012 [Page 9]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
client can consider using smaller DELIVERBY timeouts for higher
priority messages.
6. Syntax
priority-value = (["-"] NZDIGIT) / "0"
; Allowed values are from -9 to 9 inclusive
NZDIGIT = %x31-39
; "1"-"9"
CFWS = <defined in RFC 5322>
; New "clause" that can be used in the Received header field
Pri = CFWS "PRIORITY" FWS priority-value
; Complies with the <Additional-Registered-Clauses>
; non-terminal syntax from RFC 5321.
7. Example
An SMTP transaction with 2 recipients. Note that the example is also
making use of the DELIVERBY [RFC2852] and DSN [RFC3461] SMTP
extensions, even though there is no requirement that these other
extensions are to be supported when the MT-PRIORITY SMTP extension is
implemented.
Melnikov & Carlberg Expires December 13, 2012 [Page 10]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
S: 220 example.net SMTP server here
C: EHLO example.com
S: 250-example.net
S: 250-DSN
S: 250-DELIVERBY
S: 250 MT-PRIORITY
C: MAIL FROM:<eljefe@example.com> BY=120;R ENVID=QQ314159
MT-PRIORITY=3
S: 250 <eljefe@example.com> sender ok
C: RCPT TO:<topbanana@example.net>
S: 250 <topbanana@example.net> recipient ok
C: RCPT TO:<Dana@Ivory.example.net> NOTIFY=SUCCESS,FAILURE
ORCPT=rfc822;Dana@Ivory.example.net
S: 250 <Dana@Ivory.example.net> recipient ok
C: DATA
S: 354 okay, send message
C: (message goes here)
C: .
S: 250 message accepted
C: QUIT
S: 221 goodbye
If the receiving SMTP server only supports 6 priority levels as
described in Section 5, it will use the priority value 4 internally
(the next supported priority higher or equal to 3) and will
communicate the priority value 3 when relaying it to the next hop (if
necessary).
8. Deployment Considerations
8.1. Multiple MX records
If multiple DNS MX records are used to specify multiple servers for a
domain in section 5 of [RFC5321], it is strongly advised that all of
them support the MT-PRIORITY extension and handles priorities in
exactly the same way. If one or more servers behave differently in
this respect, then it is strongly suggested that none of the servers
support the MT-PRIORITY extension. Otherwise, unexpected differences
in message delivery speed or even rejections can happen during
temporary or permanent failures, which users might perceive as
serious reliability issues.
8.2. Consistent priority handling policy
This document allows up to 19 distinct priority values. In a
particular operating environment independent originators need to
assign priority values according to roughly the same criteria, so
that the same "high priority message" doesn't get associated with the
Melnikov & Carlberg Expires December 13, 2012 [Page 11]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
value 3 for one sender and with the value 5 for another, as such
messages might end up getting different preferential treatment when
it was not the intent.
In order to achieve consistent behaviour in an operating environment,
the priority assignment policy (together with restrictions on maximum
message sized for each priority (if any), default timeouts, etc.)
should be documented for the environment. The default priority
assignment policy is specified in Appendix A. Two other anticipated
policies are specified in Appendix B and Appendix C.
Moreover, all MSAs/MTAs/MDAs within any given Administrative
Management Domain has to be configured to use the same priority
related policy. Otherwise a differently configured MSA/MTA/MDA can
expose the whole domain to possible attacks, like injection of hight
priority fake-DSN.
When this SMTP extension is deployed across multiple cooperating
Administrative Domains, such Administrative Domains need to use the
same or at least compatible policies. Again, differences in policies
(for example differences in how users are authenticated or
differences in how priorities are handled) can expose an
Administrative Domain to weaknesses in a partner domain.
9. IANA Considerations
This specification requests IANA to add the MT-PRIORITY SMTP
extension to the "SMTP Service Extensions" registry (in
http://www.iana.org/assignments/mail-parameters). This extension is
suitable for the Submit port.
This specification requests IANA to add the following new Received
header field clause to the "Additional-registered-clauses" sub-
registry (in http://www.iana.org/assignments/mail-parameters) to help
with tracing email messages delivered using the MT-PRIORITY SMTP
extension:
Clause name: PRIORITY
Description: Records the value of the MT-PRIORITY parameter specified
in the MAIL FROM command
Syntax of the value: See Section 6 of RFCXXXX
Reference: [[anchor12: RFCXXXX]]
This specification requests IANA to add the following Enumerated
Status Codes to the "Simple Mail Transfer Protocol (SMTP) Enhanced
Status Codes" registry established by [RFC5248] (in http://
www.iana.org/assignments/smtp-enhanced-status-codes/
smtp-enhanced-status-codes.xml):
Melnikov & Carlberg Expires December 13, 2012 [Page 12]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
1.
Code: X.7.TBD1
Sample Text: Priority Level is too low
Associated basic status code: 450, 550 (other 4XX or 5XX codes
are allowed)
Description: The specified priority level is below the lowest
priority acceptable for the receiving SMTP server. This
condition might be temporary, for example the server is
operating in a mode where only higher priority messages are
accepted for transfer and delivery, while lower priority
messages are rejected.
Reference: RFC XXXX
Submitter: A. Melnikov
Change controller: IESG
2.
Code: X.3.TBD2
Sample Text: Message is too big for the specified priority
Associated basic status code: 552 (other 4XX or 5XX codes are
allowed)
Description: The message is too big for the specified priority.
This condition might be temporary, for example the server is
operating in a mode where only higher priority messages below
certain size are accepted for transfer and delivery.
Reference: RFC XXXX
Submitter: A. Melnikov
Change controller: IESG
3.
Code: X.3.TBD3
Melnikov & Carlberg Expires December 13, 2012 [Page 13]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
Sample Text: Requested priority was downgraded
Associated basic status code: 250 or 251
Description: The message was accepted for relay/delivery, but
the requested priority can't be honoured and was downgraded.
The human readable text after the status code contains the new
priority, followed by SP (space) and explanatory human
readable text.
Reference: RFC XXXX
Submitter: A. Melnikov
Change controller: IESG
10. Security Considerations
Message Submission Agents ought to only accept message transfer
priorities from users (or only certain groups of such users) who are
authenticated and authorized in some way that's acceptable to the
MSA. As part of this policy, they can also restrict maximum priority
values that different groups of users can request, and can override
the priority values specified by MUAs.
Similarly, MTAs ought to only accept message transfer priorities from
senders (or only certain groups of such senders) who are
authenticated and authorized in some way that's acceptable to the
MTA. As part of this policy, they can also restrict maximum priority
values that different groups of senders can request, and can override
the priority values specified by them.
In the absence of the policy enforcement mentioned above an SMTP
server (whether an MSA or an MTA) implementing this SMTP extension
might be susceptible to a Denial of Service attack. For example,
malicious clients (MUAs/MSAs/MTAs) can try to abuse this feature by
always requesting Priority 9.
11. References
11.1. Normative References
[RFC2033] Myers, J., "Local Mail Transfer Protocol",
RFC 2033, October 1996.
[RFC2034] Freed, N., "SMTP Service Extension for
Returning Enhanced Error Codes", RFC 2034,
October 1996.
Melnikov & Carlberg Expires December 13, 2012 [Page 14]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
[RFC2119] Bradner, S., "Key words for use in RFCs to
Indicate Requirement Levels", BCP 14, RFC 2119,
March 1997.
[RFC3461] Moore, K., "Simple Mail Transfer Protocol
(SMTP) Service Extension for Delivery Status
Notifications (DSNs)", RFC 3461, January 2003.
[RFC5321] Klensin, J., "Simple Mail Transfer Protocol",
RFC 5321, October 2008.
[RFC5322] Resnick, P., Ed., "Internet Message Format",
RFC 5322, October 2008.
[RFC5234] Crocker, D. and P. Overell, "Augmented BNF for
Syntax Specifications: ABNF", STD 68, RFC 5234,
January 2008.
[RFC5248] Hansen, T. and J. Klensin, "A Registry for SMTP
Enhanced Mail System Status Codes", BCP 138,
RFC 5248, June 2008.
[RFC6409] Gellens, R. and J. Klensin, "Message Submission
for Mail", STD 72, RFC 6409, November 2011.
11.2. Informative References
[RFC5598] Crocker, D., "Internet Mail Architecture",
RFC 5598, July 2009.
[RFC1845] Crocker, D. and N. Freed, "SMTP Service
Extension for Checkpoint/Restart", RFC 1845,
September 1995.
[RFC1870] Klensin, J., Freed, N., and K. Moore, "SMTP
Service Extension for Message Size
Declaration", STD 10, RFC 1870, November 1995.
[RFC2156] Kille, S., "MIXER (Mime Internet X.400 Enhanced
Relay): Mapping between X.400 and RFC 822/
MIME", RFC 2156, January 1998.
[RFC2205] Braden, B., Zhang, L., Berson, S., Herzog, S.,
and S. Jamin, "Resource ReSerVation Protocol
(RSVP) -- Version 1 Functional Specification",
RFC 2205, September 1997.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D.
Melnikov & Carlberg Expires December 13, 2012 [Page 15]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
Black, "Definition of the Differentiated
Services Field (DS Field) in the IPv4 and IPv6
Headers", RFC 2474, December 1998.
[RFC2852] Newman, D., "Deliver By SMTP Service
Extension", RFC 2852, June 2000.
[RFC4190] Carlberg, K., Brown, I., and C. Beard,
"Framework for Supporting Emergency
Telecommunications Service (ETS) in IP
Telephony", RFC 4190, November 2005.
[RFC4412] Schulzrinne, H. and J. Polk, "Communications
Resource Priority for the Session Initiation
Protocol (SIP)", RFC 4412, February 2006.
[PRIORITY-TUNNELING] Melnikov, A. and K. Carlberg, "Tunneling of
SMTP Message Transfer Priorities",
draft-melnikov-smtp-priority-tunneling-00 (work
in progress), 2012.
[ACP123] CCEB, "Common Messaging strategy and
procedures", ACP 123, May 2009.
[STANAG-4406] NATO, "STANAG 4406 Edition 2: Military Message
Handling System", STANAG 4406, March 2005.
[GREYLISTING] Kucherawy, M. and D. Crocker, "Email
Greylisting: An Applicability Statement for
SMTP", draft-ietf-appsawg-greylisting (work in
progress), April 2012.
[RFC4125] Le Faucheur, F. and W. Lai, "Maximum Allocation
Bandwidth Constraints Model for Diffserv-aware
MPLS Traffic Engineering", RFC 4125, June 2005.
[RFC4127] Le Faucheur, F., "Russian Dolls Bandwidth
Constraints Model for Diffserv-aware MPLS
Traffic Engineering", RFC 4127, June 2005.
[RFC6401] Le Faucheur, F., Polk, J., and K. Carlberg,
"RSVP Extensions for Admission Priority",
RFC 6401, October 2011.
Appendix A. Mapping of MT-PRIORITY parameter values for Military
Messaging
Military Messaging as specified in ACP 123 [ACP123] (also specified
Melnikov & Carlberg Expires December 13, 2012 [Page 16]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
in STANAG 4406 [STANAG-4406]) defines six priority ("precedence")
values. Where SMTP is used to support military messaging, the
following mappings SHOULD be used.
Recommended mapping of MT-PRIORITY values for MMHS
+----------------+-----------+
| Priority value | MMHS name |
+----------------+-----------+
| -4 | Deferred |
| -2 | Routine |
| 0 | Priority |
| 2 | Immediate |
| 4 | Flash |
| 6 | Override |
+----------------+-----------+
Table 1
Appendix B. Mapping of MT-PRIORITY parameter values for MIXER
MIXER [RFC2156] defines the Priority header field with 3 values.
Where SMTP is used to support MIXER messaging, the following mappings
SHOULD be used.
Recommended mapping of MT-PRIORITY values for MIXER
+----------------------+-------------------+
| MIXER Priority value | MT-PRIORITY value |
+----------------------+-------------------+
| non-urgent | -4 |
| normal | 0 |
| urgent | 4 |
+----------------------+-------------------+
Table 2
Appendix C. Mapping of National Security / Emergency Preparedness
(NS/EP) Values
There are several forms of communication systems used during an
emergency or disaster. The most well known form involves the many-
to-one model of the general public contacting a public safety access
point via 911/999/112 calls through the public telephone network.
Typically, these calls do not require authorization, nor do they
invoke any prioritization.
Another form of emergency communications involves a set of authorized
Melnikov & Carlberg Expires December 13, 2012 [Page 17]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
users or nodes that use prioritized services to help established and
continue communication given limited available resources. [RFC4190]
includes descriptions of several systems that have been developed to
support National Security / Emergency Preparedness (NS/EP). These
deployed systems require a form of authentication and have focused on
prioritization of telephony based services. They have also been
designed as a binary form (on/off) of signaled priority
communications.
[RFC4412] includes examples of a more expansive view of NS/EP
communications in which priority migrates from a single on/off bit
value to one that comprises five priority values. This is shown in
the cases of the ETS and WPS Namespaces. Given a lack of pre-
existing NS/EP values assigned for email, we follow the paradigm of
the ETS and WPS Namespaces and recommend five ascending values shown
in the table below.
+----------------+------------------+
| Priority value | Relational Order |
+----------------+------------------+
| -2 | Lowest Priority |
| 0 | ---------- |
| 2 | ---------- |
| 4 | ---------- |
| 6 | Highest Priority |
+----------------+------------------+
As in the case of Appendix A and Appendix B, the gap in numeric
values listed in this table provides room for future changes to
expand the set of priorities at a future date, or in a local and non-
standardized manner.
Appendix D. Possible implementation strategies
This appendix suggest some implementation strategies to implement the
SMTP extension defined in this document. The list is not exhaustive.
This appendix and its subsections are Informative.
D.1. Probability
As the name suggests, probability involves increasing the chances of
obtaining resources without adversely affecting previously
established connections. One example would involve requesting
resources set aside for specific priority levels. If these
additional resources are exhausted, then the desired connection is
denied. Queues, new timers, or combinations thereof can be used to
facilitate the higher priority requests, but the key is that
Melnikov & Carlberg Expires December 13, 2012 [Page 18]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
mechanisms focus on increasing the probability of message transfer.
D.2. Preemption of sessions or transactions
Preemption is a type of action that focuses only on a comparison of
priorities to determine if previously established transactions need
to be displaced in favor of higher priority requests. If no
additional connection is possible, the client aborts a running
session for emails with lower priority no later than directly after
the current transaction. The client even can interrupt an active
transaction and ought to do so, if other constraints such as delivery
time (as specified in the DELIVERBY SMTP extension [RFC2852]) would
be violated for the email with higher priority. When interrupting an
active transaction, the client ought to take the total message size
and the size of the transferred portion of the message being
interrupted into consideration. This preliminary termination of
sessions or transactions is called preemption.
If preemption of running transactions occurs, the client needs to
choose a transaction with the lowest priority currently processed.
If the client has an option (i.e. it is supported by the next hop
MTA) to interrupt transactions in a way that it can be restarted at
the interruption point later, it ought to deploy it. An example for
a mechanism providing such a service is the "SMTP Service Extension
for Checkpoint/Restart" defined in [RFC1845].
If a client opts for the preemption of sessions instead of
transactions, it needs to preempt the next session that reaches the
end of a transaction.
D.3. Resource Allocation Models
Adding prioritization to a design moves the subject away from
strictly best effort (and a first-come-first-served model) to one
that includes admission control and resource allocation models. Over
the years, a variety of work has been done within the IETF in
specifying resource allocations models. Examples include the Maximum
Allocation Model [RFC4125], the Russian Dolls Model [RFC4127], and
the Priority Bypass Model (Appendix A.3 of [RFC6401]).
While we recognize that these various models have been designed for
other protocols (i.e., MPLS and RSVP), an understanding of their
design characteristics may be beneficial in considering future
implementations of a priority SMTP service.
In cases where the processing of high priority messages by an MTA is
not considered negligible and exceeds engineered expectations, then
Melnikov & Carlberg Expires December 13, 2012 [Page 19]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
operators managing that MTA may be notified in some form (e.g.,
pushed alarm, polled status).
Appendix E. Background on Design Choices
This Section provides some background on design choices made during
development of the MT-PRIORITY SMTP extension.
The priority applies per message, rather than per recipient in order
to keep the protocol simpler, and because of the expectation that it
will be uncommon to need different priorities for different
recipients on the same message. In cases where that is necessary, it
can always be achieved by sending separate messages with the same
content, segregating the recipients by desired message priority.
The choice of the priority range -9 to 9 (as opposed to, say, 1 to 6,
or 0 to 9) was made after taking the following into consideration:
1. Clearly, having multiple priority levels is the whole point of
this extension. Existing implementations of similar
functionality in MTAs are already using three levels. One of the
use cases motivating this extension requires six levels. So at
least six different values are required.
2. During discussions of this extension, several different use cases
were suggested that required differing numbers of priority
levels. Defining just the six priority levels needed in item 1,
above, would limit the extensibility for possible future use
cases. Therefore, this document is defining a wider range, which
allows implementations and deployments to add higher or lower
priority levels and to insert additional priority levels between
the recommended set of six. This avoids the need to further
extend this extension just to have a few more priority levels.
3. It seems natural to use 0 for the "normal" or default priority,
rather than picking some non-zero number and having the
priorities go up or down from there. This way, negative numbers
always represent priorities that are lower than normal, with
positive numbers as higher priorities.
Appendix F. Acknowledgements
This document copies lots of text from
draft-schmeing-smtp-priorities-04.txt and
draft-schmeing-smtp-priorities-05.txt. So the authors of this
document would like to acknowledge contributions made by the authors
of draft-schmeing-smtp-priorities: Michael Schmeing and Jan-Wilhelm
Brendecke.
Melnikov & Carlberg Expires December 13, 2012 [Page 20]
Internet-Draft Message Transfer Priority SMTP Extension June 2012
Many thanks for input provided by Steve Kille, David Wilson, John
Klensin, Dave Crocker, Graeme Lunt, Alessandro Vesely, Barry Leiba,
Bill McQuillan, Murray Kucherawy, SM, Glenn Parsons, Pete Resnick,
Chris Newman, Ned Freed and Claudio Allocchio.
Special thanks to Barry Leiba for agreeing to shepherd this document.
Authors' Addresses
Alexey Melnikov
Isode Ltd
5 Castle Business Village
36 Station Road
Hampton, Middlesex TW12 2BX
UK
EMail: Alexey.Melnikov@isode.com
Ken Carlberg
G11
1601 Clarendon Blvd, #203
Arlington, VA 22209
USA
EMail: carlberg@g11.org.uk
Melnikov & Carlberg Expires December 13, 2012 [Page 21]