Network G. Mirsky
Internet-Draft ZTE Corp.
Intended status: Standards Track P. Shaofu
Expires: August 30, 2018 ZTE Corporation
February 26, 2018
Unified Identifier in IPv6 Segment Routing Networks
draft-mirsky-6man-unified-id-sr-00
Abstract
Segment Routing architecture leverages the paradigm of source
routing. It can be realized in a network data plane by prepending
the packet with a list of instructions, a.k.a. segments. A segment
can be encoded as an Multi-Protocol Label Switching (MPLS) label,
IPv4 address or IPv6 address. Segment Routing can be applied in MPLS
data plane by encoding segments in MPLS label stack. It also can be
applied to IPv6 data plane by encoding list of segment identifiers in
IPv6 Segment Routing Extension Header (SRH). This document extends
the use of the SRH to segment identifiers encoded as MPLS label and
IPv4 address.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 30, 2018.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
Mirsky & Shaofu Expires August 30, 2018 [Page 1]
Internet-Draft Unified Identifier SRv6 February 2018
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Conventions used in this document . . . . . . . . . . . . 3
1.1.1. Terminology . . . . . . . . . . . . . . . . . . . . . 3
1.1.2. Requirements Language . . . . . . . . . . . . . . . . 3
2. Segment Routing Extension Header: Benefits and Challenges . . 3
3. Support of Multiple SID Lengths in IPv6 Segment Routing
Extension Header . . . . . . . . . . . . . . . . . . . . . . 4
4. Theory of Operation . . . . . . . . . . . . . . . . . . . . . 5
4.1. Egress SR Tunnel Node . . . . . . . . . . . . . . . . . . 5
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 5
6. Security Considerations . . . . . . . . . . . . . . . . . . . 5
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 5
8. Normative References . . . . . . . . . . . . . . . . . . . . 5
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 7
1. Introduction
Segment Routing architecture [I-D.ietf-spring-segment-routing]
leverages the paradigm of source routing. It can be realized in a
network data plane by prepending the packet with a list of
instructions, a.k.a. segment identifiers (SIDs). A segment can be
encoded as an Multi-Protocol Label Switching (MPLS) label, IPv4
address or IPv6 address. Segment Routing can be applied in MPLS data
plane by encoding 20-bits SIDs in MPLS label stack
[I-D.ietf-spring-segment-routing-mpls]. It also can be applied to
IPv6 data plane by encoding list of 128-bits SIDs in IPv6 Segment
Routing Extension Header (SRH)
[I-D.ietf-6man-segment-routing-header]. Applicability of 32-bits
SID, that may represent IPv4 address, has not been defined.
SR extensions to Interior Gateway Protocols (IGP), IS-IS
[I-D.ietf-isis-segment-routing-extensions], OSPF
[I-D.ietf-ospf-segment-routing-extensions], and OSPFv3
[I-D.ietf-ospf-ospfv3-segment-routing-extensions], defined how
20-bits and 32-bits SIDs advertised and bound to SR objects and/or
instructions. Extensions to BGP link-state address family
[I-D.ietf-idr-bgp-ls-segment-routing-ext] enabled propagation of
segment information of variable length via BGP.
Mirsky & Shaofu Expires August 30, 2018 [Page 2]
Internet-Draft Unified Identifier SRv6 February 2018
This document extends the use of the SRH
[I-D.ietf-6man-segment-routing-header] to SIDs encoded as MPLS label
and IPv4 address.
1.1. Conventions used in this document
1.1.1. Terminology
SR: Segment Routing
SRH: Segment Routing Extension Header
MPLS: Multiprotocol Label Switching
MPLS-SR: Segment Routing in MPLS
SID: Segment Identifier
IGP: Interior Gateway Protocol
OAM: Operation, Administration and Maintenance
TE: Traffic Engineering
SRv6: Segment Routing in IPv6
1.1.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Segment Routing Extension Header: Benefits and Challenges
Many functions related to Operation, Administration and Maintenance
(OAM) require identification of the SR tunnel ingress and the path,
constructed by segments, between the ingress and the egress SR nodes.
Combination of IPv6 encapsulation [RFC8200] and SRH
[I-D.ietf-6man-segment-routing-header], referred to as SRv6, comply
with this requirements while it is challenging when applying SR in
MPLS networks, also referred to as MPLS-SR.
On the other hand, size of IPv6 SID presents scaling challenge to use
topological instructions that define strict explicit traffic
engineered (TE) path in combination with service-based instructions.
Mirsky & Shaofu Expires August 30, 2018 [Page 3]
Internet-Draft Unified Identifier SRv6 February 2018
At the same time, that is where MPLS-SR approach provides better
results due to smaller SID length.
[I-D.bryant-mpls-unified-ip-sr] addresses the scaling challenge by
using more compact SID encoding of MPLS-SR. Ability to address OAM
challenge characteristic to MPLS-SR is open for investigation.
3. Support of Multiple SID Lengths in IPv6 Segment Routing Extension
Header
In section 3 of [I-D.ietf-6man-segment-routing-header] SRH format has
been defined as presented in Figure 1
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Last Entry | Flags | Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Segment List[0] (128 bits IPv6 address) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| |
...
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Segment List[n] (128 bits IPv6 address) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// //
// Optional Type Length Value objects (variable) //
// //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: SRH format
This document defines the new field Size in the Flags field,
presented in Figure 2, as two-bits field with the following values:
0b00 - 128-bits SID;
Mirsky & Shaofu Expires August 30, 2018 [Page 4]
Internet-Draft Unified Identifier SRv6 February 2018
0b01 - 20-bits SID;
0b10 - 32-bits SID
0b11 - reserved for future use.
When the value of the S field is 0b01, the 20-bit SID is encoded in
four octets and occupies the 20 rightmost bits.
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|U|P|O|A|H| S |U|
+-+-+-+-+-+-+-+-+
Figure 2: Flags field format
Entries of the segment list in the SRH MUST be of the same length.
4. Theory of Operation
When the SRH is used to include 20-bits or 32-bits SIDs the ingress
and transit nodes of an SR tunnel act as described in Section 5.1 and
Section 5.2 of [I-D.ietf-6man-segment-routing-header] respectively.
4.1. Egress SR Tunnel Node
TBD
5. IANA Considerations
TBD
6. Security Considerations
This specification inherits all security considerations of
[I-D.ietf-spring-segment-routing] and
[I-D.ietf-6man-segment-routing-header].
7. Acknowledgements
TBD
8. Normative References
[I-D.bryant-mpls-unified-ip-sr]
Bryant, S., Farrel, A., Drake, J., and J. Tantsura, "MPLS
Segment Routing in IP Networks", draft-bryant-mpls-
unified-ip-sr-03 (work in progress), October 2017.
Mirsky & Shaofu Expires August 30, 2018 [Page 5]
Internet-Draft Unified Identifier SRv6 February 2018
[]
Previdi, S., Filsfils, C., Raza, K., Dukes, D., Leddy, J.,
Field, B., daniel.voyer@bell.ca, d.,
daniel.bernier@bell.ca, d., Matsushima, S., Leung, I.,
Linkova, J., Aries, E., Kosugi, T., Vyncke, E., Lebrun,
D., Steinberg, D., and R. Raszuk, "IPv6 Segment Routing
Header (SRH)", draft-ietf-6man-segment-routing-header-08
(work in progress), January 2018.
[I-D.ietf-idr-bgp-ls-segment-routing-ext]
Previdi, S., Talaulikar, K., Filsfils, C., Gredler, H.,
and M. Chen, "BGP Link-State extensions for Segment
Routing", draft-ietf-idr-bgp-ls-segment-routing-ext-04
(work in progress), January 2018.
[I-D.ietf-isis-segment-routing-extensions]
Previdi, S., Ginsberg, L., Filsfils, C., Bashandy, A.,
Gredler, H., Litkowski, S., Decraene, B., and J. Tantsura,
"IS-IS Extensions for Segment Routing", draft-ietf-isis-
segment-routing-extensions-15 (work in progress), December
2017.
[I-D.ietf-ospf-ospfv3-segment-routing-extensions]
Psenak, P., Filsfils, C., Previdi, S., Gredler, H.,
Shakir, R., Henderickx, W., and J. Tantsura, "OSPFv3
Extensions for Segment Routing", draft-ietf-ospf-ospfv3-
segment-routing-extensions-11 (work in progress), January
2018.
[I-D.ietf-ospf-segment-routing-extensions]
Psenak, P., Previdi, S., Filsfils, C., Gredler, H.,
Shakir, R., Henderickx, W., and J. Tantsura, "OSPF
Extensions for Segment Routing", draft-ietf-ospf-segment-
routing-extensions-24 (work in progress), December 2017.
[I-D.ietf-spring-segment-routing]
Filsfils, C., Previdi, S., Ginsberg, L., Decraene, B.,
Litkowski, S., and R. Shakir, "Segment Routing
Architecture", draft-ietf-spring-segment-routing-15 (work
in progress), January 2018.
[I-D.ietf-spring-segment-routing-mpls]
Bashandy, A., Filsfils, C., Previdi, S., Decraene, B.,
Litkowski, S., and R. Shakir, "Segment Routing with MPLS
data plane", draft-ietf-spring-segment-routing-mpls-12
(work in progress), February 2018.
Mirsky & Shaofu Expires August 30, 2018 [Page 6]
Internet-Draft Unified Identifier SRv6 February 2018
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", STD 86, RFC 8200,
DOI 10.17487/RFC8200, July 2017,
<https://www.rfc-editor.org/info/rfc8200>.
Authors' Addresses
Greg Mirsky
ZTE Corp.
Email: gregimirsky@gmail.com
Peng Shaofu
ZTE Corporation
No.50 Software Avenue, Yuhuatai District
Nanjing
China
Email: peng.shaofu@zte.com.cn
Mirsky & Shaofu Expires August 30, 2018 [Page 7]