INTERNET-DRAFT Thomas Narten
IBM
<draft-narten-canonical-ordering-00.txt> Charles Burton
IBM
November 5, 1997
A Caution On The Canonical Ordering Of Link-Layer Addresses
<draft-narten-canonical-ordering-00.txt>
Status of this Memo
This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
To learn the current status of any Internet-Draft, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ds.internic.net (US East Coast), nic.nordu.net
(Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific
Rim).
Distribution of this memo is unlimited.
This Internet Draft expires May 5, 1998.
Abstract
Protocols such as ARP and Neighbor Discovery have data fields that
contain link-layer addresses. In order to interoperate properly, a
sender setting such a field must insure that the receiver extracts
those bits and interprets them correctly. In most cases, such fields
must be in "canonical form." Unfortunately, not all LAN adaptors are
consistent in their use of canonical form, and implementations may
need to explicitly bit swap individual bytes in order to obtain the
correct format. This document provides information to implementors to
help them avoid the pitfall of using non-canonical forms when
canonical forms are required.
draft-narten-canonical-ordering-00.txt [Page 1]
INTERNET-DRAFT October 6, 1997
Contents
Status of this Memo.......................................... 1
1. Introduction............................................. 2
2. Canonical Form........................................... 2
3. Implementors Beware: Potential Trouble Spots............. 3
3.1. Neighbor Discovery in IPv6.......................... 3
3.2. IPv4 and ARP........................................ 4
4. Security Considerations.................................. 4
5. References............................................... 4
6. Authors' Addresses....................................... 4
1. Introduction
Protocols such as ARP [ARP] and ND [DISCOVERY] have data fields that
contain link-layer addresses. In order to interoperate properly, a
sender setting such a field must insure that the receiver extracts
those bits and interprets them correctly. In most cases, such fields
must be in "canonical form." Unfortunately, not all LAN adaptors are
consistent in their use of canonical form, and implementations may
need to explicitly bit swap individual bytes in order to obtain the
correct format.
2. Canonical Form
Canonical form (also known as "LSB format" and "Ethernet format") is
the name given to the format of a LAN adapter address as it should be
presented to the user according to the 802 LAN standard. It is best
defined as how the bit order of an adapter address on the LAN media
maps to the bit order of an adapter address in memory: The first bit
of each byte that appears on the LAN maps to the least significant
(i.e., right-most) bit of each byte in memory (the figure below
illustrates this). This puts the group address indicator (i.e., the
bit that defines whether an address is unicast or multicast) in the
least significant bit of the first byte. Ethernet and 802.3 hardware
behave consistently with this definition.
Unfortunately, Token Ring (and some FDDI) hardware does not behave
consistently with this definition; it maps the first bit of each byte
of the adapter address to the most significant (i.e., left-most) bit
draft-narten-canonical-ordering-00.txt [Page 2]
INTERNET-DRAFT October 6, 1997
of each byte in memory, which puts the group address indicator in the
most significant bit of the first byte. This mapping is variously
called "MSB format", "IBM format", "Token-Ring format", and "non-
canonical form". The figure below illustrates the difference between
canonical and non-canonical form using the canonical form address
12-34-56-78-9A-BC as an example:
In memory, 12 34 56 78 9A BC
canonical: 00010010 00110100 01010110 01111000 10011010 10111100
1st bit appearing on LAN (group address indicator)
|
On LAN: 01001000 00101100 01101010 00011110 01011001 00111101
In memory,
MSB format: 01001000 00101100 01101010 00011110 01011001 00111101
48 2C 6A 1E 59 3D
The implication of this inconsistency is that addresses extracted
from adaptors, assigned to adaptors, or extracted from link-layer
packet headers obtained from adaptors may need to be bit-swapped to
put them into canonical form. Likewise, addresses in canonical form
that are handed to adaptors (e.g., to set an address, to specify a
destination address in a link-layer header, etc.) may need to be
bit-swapped in order for the adaptor to process the request as
expected.
3. Implementors Beware: Potential Trouble Spots
3.1. Neighbor Discovery in IPv6
All of the IPv6 over specific link layers documents specify that
link-layer addresses must be transmitted in canonical order [IPv6-
ETHER, IPv6-FDDI, IPv6-TOKEN]. As far as the authors can tell, all
Ethernet LAN adaptors use canonical order and no special processing
by implementations is needed. In contrast, some FDDI and all Token
Ring adaptors appear to use non-canonical format. Implementors must
insure that any addresses that appear in link-layer address options
of Neighbor Discovery [DISCOVERY] messages are sent in canonical
order and that any link-layer addresses extracted from ND packets are
interpreted correctly on the local machine and its adaptors.
draft-narten-canonical-ordering-00.txt [Page 3]
INTERNET-DRAFT October 6, 1997
3.2. IPv4 and ARP
Ethernet addresses that appear in ARP packets are in canonical order.
In contrast, when running ARP over Token Ring, the de facto practice
is to transmit addresses in non-canonical order. Because all Token
Ring adaptors assume non-canonical ordering, no interoperability
problems result between communicating nodes attached to the same
Token Ring.
In some environments, however, Token Rings and Ethernets are
connected via a bridge. When a node on the Token Ring attempts to
communicate with a node on the Ethernet, communication would normally
fail, since the Ethernet will misinterpret the Token Ring address
(and vice versa). To get around this problem, bridges that forward
packets between dissimilar network types perform bit swaps of the
addresses in the address fields of ARP packets that are forwarded
from a network of one type to one of the other.
4. Security Considerations
There are no known security issues raised by this document.
5. References
[ARP] D. Plummer, "An Ethernet Address Resolution Protocol", STD
37, RFC 826, November 1982.
[DISCOVERY] Narten, T., Nordmark, E., and W. Simpson, "Neighbor
Discovery for IP Version 6 (IPv6)", draft-ietf-ipngwg-
discovery-v2-00.txt.
[IPv6-ETHER] M. Crawford, "Transmission of IPv6 Packets over
Ethernet Networks", draft-ietf-ipngwg-trans-ethernet-
03.txt.
[IPv6-FDDI] M. Crawford, "Transmission of IPv6 Packets over FDDI
Networks", draft-ietf-ipngwg-trans-fddi-net-03.txt.
[IPv6-TOKEN] S. Thomas, "Transmission of IPv6 Packets over Token
Ring Networks", draft-ietf-ipngwg-trans-tokenring-03.txt.
6. Authors' Addresses
Thomas Narten
IBM Corporation
3039 Cornwallis Ave.
PO Box 12195
draft-narten-canonical-ordering-00.txt [Page 4]
INTERNET-DRAFT October 6, 1997
Research Triangle Park, NC 27709-2195
Phone: 919-254-7798
EMail: narten@raleigh.ibm.com
Charles F. Burton, III
IBM Corporation
3039 Cornwallis Ave.
PO Box 12195
Research Triangle Park, NC 27709-2195
Phone: 919-254-4355
EMail: burton@rtp.vnet.ibm.com
draft-narten-canonical-ordering-00.txt [Page 5]