Network Working Group                                      Eric C. Rosen
Internet Draft                                       Cisco Systems, Inc.
Expiration Date: November 2003

                                                                May 2003


    Provisioning Models and Endpoint Identifiers in L2VPN Signaling


                 draft-rosen-ppvpn-l2-signaling-03.txt

Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that other
   groups may also distribute working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

Abstract

   [PWE3-CONTROL] specifies a "signaling protocol" which uses extensions
   of LDP [RFC 3036] to set up and maintain pseudowires [PWE3-FR, PWE3-
   ARCH].  Like any protocol which sets up connections, the signaling
   protocol provides a method by which each endpoint can identify the
   other.  [L2VPN-FW] describes a number of different ways in which sets
   of pseudowires may be combined together into "Provider Provisioned
   Layer 2 VPNs" (L2 PPVPNs, or L2VPNs), resulting in a number of
   different kinds of L2VPN.  Different kinds of L2VPN may have
   different "provisioning models", i.e., different models for what
   information needs to be configured in what entities. Once configured,
   the provisioning information is distributed by a "discovery process",
   and once the information is discovered, the signaling protocol is
   automatically invoked to set up the required pseudowires.  The
   semantics of the endpoint identifiers which the signaling protocol



Rosen                                                           [Page 1]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   uses for a particular type of L2VPN are determined by the
   provisioning model.  This document specifies a number of PPVPN
   provisioning models, and specifies the semantic structure of the
   endpoint identifiers required. It further specifies how the endpoint
   identifiers are carried in the "Generalized Identifier FEC" of
   [PWE3-CONTROL].  It is believed that the specified identifiers can
   also be carried within the L2TP signaling protocol, though this is
   currently not specified.











































Rosen                                                           [Page 2]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003




Contents

    1        Introduction  .........................................   4
    2        Signaling Protocol Framework  .........................   5
    2.1      Endpoint Identification  ..............................   5
    2.2      Association of two LSPs as one Pseudowire  ............   6
    2.3      Attachment Identifiers and Forwarders  ................   7
    3          .....................................................   9
    4          .....................................................   9
    5        Applications  .........................................   9
    5.1      Individual Point-to-Point VCs  ........................   9
    5.1.1    Provisioning Models  ..................................   9
    5.1.1.1  Double Sided Provisioning  ............................   9
    5.1.1.2  Single Sided Provisioning with Discovery  .............   9
    5.1.2    Signaling  ............................................  10
    5.2      Virtual Private LAN Service  ..........................  11
    5.2.1    Provisioning  .........................................  11
    5.2.2    Auto-Discovery  .......................................  11
    5.2.2.1  BGP-based auto-discovery  .............................  11
    5.2.2.2  Radius-based auto-discovery  ..........................  12
    5.2.3    Signaling  ............................................  13
    5.3      Colored Pools: Full Mesh of Point-to-Point VCs  .......  13
    5.3.1    Provisioning  .........................................  13
    5.3.2    Auto-Discovery  .......................................  14
    5.3.2.1  BGP-based auto-discovery  .............................  14
    5.3.2.2  Radius-based Auto-Discovery  ..........................  15
    5.3.3    Signaling  ............................................  15
    5.4      Colored Pools: Partial Mesh  ..........................  16
    5.5      Distributed VPLS  .....................................  16
    5.5.1    Signaling  ............................................  18
    5.5.2    Provisioning and Discovery  ...........................  19
    5.5.3    Non-distributed VPLS as a sub-case  ...................  20
    5.5.4    Inter-Provider Application of Dist. VPLS Signaling  ...  20
    5.5.5    Splicing and the Data Plane  ..........................  21
    6        Security Considerations  ..............................  22
    7        Acknowledgments  ......................................  22
    8        References  ...........................................  22
    9        Author's Information  .................................  23











Rosen                                                           [Page 3]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


1. Introduction

   [PWE3-CONTROL] specifies a "signaling protocol" which uses extensions
   of LDP [RFC 3036] to set up and maintain pseudowires [PWE3-FR, PWE3-
   ARCH].  Like any protocol which sets up connections, the signaling
   protocol provides a method by which each endpoint can identify the
   other.  [L2VPN-FW] describes a number of different ways in which sets
   of pseudowires may be combined together into "Provider Provisioned
   Layer 2 VPNs" (L2 PPVPNs, or L2VPNs), resulting in a number of
   different kinds of L2VPN.  Different kinds of L2VPN may have
   different "provisioning models", i.e., different models for what
   information needs to be configured in what entities. Once configured,
   the provisioning information is distributed by a "discovery process",
   and once the information is discovered, the signaling protocol is
   automatically invoked to set up the required pseudowires.  The
   semantics of the endpoint identifiers which the signaling protocol
   uses for a particular type of L2VPN are determined by the
   provisioning model.  This document specifies a number of PPVPN
   provisioning models, and specifies the semantic structure of the
   endpoint identifiers required. It further specifies how the endpoint
   identifiers are carried in the "Generalized Identifier FEC" of
   [PWE3-CONTROL].  It is believed that the specified identifiers can
   also be carried within the L2TP signaling protocol, though this is
   currently not specified.

   We make free use of terminology from [L2VPN-FW], [L2VPN-TERM],
   [PWE3-ARCH] and [PWE3-FR], in particular the terms "Attachment
   Circuit", "pseudowire", "PE", "CE".

   Section 2 provides an overview of the relevant aspects of [PWE3-
   CONTROL].

   Section 5 details various provisioning models and relates them to the
   signaling process (using the Generalized Identifier FEC) and to the
   discovery process.

   We do not specify an auto-discovery procedure in this draft, but we
   do specify the information which needs to be obtained via auto-
   discovery in order for the signaling procedures to begin.  The way in
   which the LDP-based signaling mechanisms can be integrated with BGP-
   based auto-discovery is covered in some detail.  Later revisions of
   this draft will provide equivalent detail for other discovery
   mechanisms.

   (Sections 3 and 4 don't exist, but section 5 retains the same section
   number it had in previous versions as it has been referenced by
   number during working group discussions.)




Rosen                                                           [Page 4]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119















2. Signaling Protocol Framework

2.1. Endpoint Identification

   Per [L2VPN-FW], a pseudowire can be thought of as a relationship
   between a pair of "Forwarders".  In simple instances of VPWS, a
   Forwarder binds a pseudowire to a single Attachment Circuit, such
   that frames received on the one are sent on the other, and vice
   versa.  In VPLS, a Forwarder binds a set of pseudowires to a set of
   Attachment Circuits; when a frame is received from any member of that
   set, a MAC address table is consulted (and various 802.1d procedures
   executed) to determine the member or members of that set on which the
   frame is to be transmitted.  In more complex scenarios, Forwarders
   may bind PWs to PWs, thereby "splicing" two PWs together; this is
   needed, e.g., to support distributed VPLS.

   In simple VPWS, where a Forwarder binds exactly one PW to exactly one
   Attachment Circuit, a Forwarder can be identified by identifying its
   Attachment Circuit.  In simple VPLS, a Forwarder can be identified by
   identifying its PE device and its VPN.

   To set up a PW between a pair of Forwarders, the signaling protocol
   must allow the Forwarder at one endpoint to identify the Forwarder at
   the other.  In [PWE3-CONTROL], the term "Attachment Identifier", or
   "AI", to refer to a quantity whose purpose is to identify a
   Forwarder.

   [PWE3-CONTROL] specifies two FEC elements which can be used for when
   setting up pseudowires, the PWid FEC element, and the Generalized Id
   FEC element.  The PWid FEC element carries only one Forwarder



Rosen                                                           [Page 5]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   identifier; it can be thus be used only when both forwarders have the
   same identifier, and when that identifier can be coded as a 32-bit
   quantity.  The Generalized Id FEC element carries two Forwarder
   identifiers, one for each of the two Forwarders  being connected.
   (The concept of carrying a local identifier and a remote identifier
   is also used in the L2TP signaling proposal described in [LUO-L2TP].)
   Each identifier is known as an Attachment Identifier, and a signaling
   message carries both a "Source Attachment Identifier" (SAI)  and a
   "Target Attachment Identifier" (TAI).

   The Generalized ID FEC element also provides some additional
   structuring of the identifiers.  It is assumed that the SAI and TAI
   will sometimes have a common part, called the "Attachment Group
   Identifier" (AGI), such that the SAI and TAI can each be thought of
   as the concatenation of the AGI with an "Attachment Individual
   Identifier" (AII).  So the pair of identifiers is encoded into three
   fields: AGI, Source AII (SAII), and Target AII (TAII).  The SAI is
   the concatenation of the AGI and the SAII, while the TAI is the
   concatenation of the AGI and the TAII.  This additional structuing
   differs from the proposal in [LUO-L2TP], which specifies only that
   there be two "endpoint identifiers".

   It should be noted that while different forwarders support different
   applications, the type of application (e.g., VPLS vs. VPWS) cannot
   necessarily be inferred from the forwarders' identifiers.  A router
   receiving a signaling message with a particular TAI will have to be
   able to determine which of its local forwarders is identified by that
   TAI, and to determine the application provided by that forwarder.
   But other nodes may not be able to infer the application simply by
   inspection of the signaling messages.


2.2. Association of two LSPs as one Pseudowire

   In any form of LDP-based signaling, each PW endpoint must initiate
   the creation of a unidirectional LSP.  A PW is a pair of such LSPs.
   In most of the PPVPN provisioning models, the two endpoints of a
   given PW can simultaneously initiate the signaling for it.  They must
   therefore have some way of determining when a given pair of LSPs are
   intended to be associated together as a single PW.

   The way in which this association is done is different for the
   various different L2VPN services and provisioning models.  The
   details appear in later sections.







Rosen                                                           [Page 6]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


2.3. Attachment Identifiers and Forwarders

   Every Forwarder in a PE must be associated with an Attachment
   Identifier (AI), either through configuration or through some
   algorithm.  The Attachment Identifier must be unique in the context
   of the PE router in which the Forwarder resides.  The combination <PE
   router, AI> must be globally unique.

   It is frequently convenient to a set of Forwarders as being members
   of a particular "group", where PWs may only be set up among members
   of a group.  In such cases, it is convenient to identify the
   Forwarders relative to the group, so that an Attachment Identifier
   would consist of  an Attachment Group Identifier (AGI) plus an
   Attachment Individual Identifier (AII).

   IT MUST BE UNDERSTOOD THAT THIS NOTION OF "GROUP" HAS NOTHING
   WHATSOEVER TO DO WITH THE "GROUP ID" THAT IS PART OF THE PWID FEC IN
   [PWE3-CONTROL].

   An Attachment  Group Identifier  may be thought  of as  a VPN-id, or
   a VLAN identifier, some  attribute which  is shared by  all the
   Attachment  VCs (or pools thereof) which are allowed to be connected.

   The details for how to construct the AGI and AII fields identifying
   the pseudowire endpoints in particular provisioning models are
   discussed later in this paper.

   We can now consider an LSP to be identified by:

           <PE1, <AGI, AII1>, PE2, <AGI, AII2>>,

   and the LSP in the opposite direction will be identified by:

           <PE2, <AGI, AII2>, PE1, <AGI, AII1>>;

   a pseudowire is a pair of such LSPs.

   When a signaling message is sent from  PE1 to PE2, and PE1 needs to
   refer to an  Attachment  Identifier which  has  been configured  on
   one  of its  own Attachment VCs  (or pools),  the Attachment
   Identifier  is called  a "Source Attachment Identifier".  If  PE1
   needs to refer to  an Attachment Identifier which has  been
   configured on  one of PE2's  Attachment VCs (or  pools), the
   Attachment Identifier  is called a  "Target Attachment Identifier".
   (So an SAI at one endpoint is a TAI at the remote endpoint, and vice
   versa.)

   In the signaling protocol, we define encodings for the following



Rosen                                                           [Page 7]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   three fields:

     - Attachment Group Identifier (AGI).

     - Source Attachment Individual Identifier (SAII)

     - Target Attachment Individual Identifier (TAII)

   If the AGI is non-null, then the SAI consists of the AGI together
   with the SAII, and the TAI consists of the TAII together with the
   AGI.  If the AGI is null, then the SAII and TAII are the SAI and TAI
   respectively.

   The  intention  is  that the  PE  which  receives  a Label  Mapping
   Message containing  a TAI  will be  able to  map  that TAI  uniquely
   to  one of  its Attachment  VCs (or  pools).   The  way in  which  a
   PE  maps  a  TAI to  an Attachment  VC (or  pool)  should  be a
   local  matter.  So  as  far as  the signaling  procedures are
   concerned, the  TAI is  really just  an arbitrary string of bytes, a
   "cookie".































Rosen                                                           [Page 8]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


3.

4.

5. Applications

   In this section, we specify the way in which the pseudowire signaling
   using the Generalized ID FEC Element is applied for a number of
   different applications.  For some of the applications, we specify the
   way in which different provisioning models can be used.  However,
   this is not meant to be an exhaustive list of the applications, or an
   exhaustive list of the provisioning models that can be applied to
   each application.


5.1. Individual Point-to-Point VCs

   The signaling specified in this document can be used to set up
   individually provisioned point-to-point pseudowires.  In this
   application, each Forwarder binds a single PW to a single Attachment
   Circuit.  Each PE must be provisioned with the necessary set of
   Attachment Circuits, and then certain parameters must be provisioned
   for each Attachment Circuit.


5.1.1. Provisioning Models

5.1.1.1. Double Sided Provisioning

   In this model, the Attachment Circuit must be provisioned with a
   local name, a remote PE address, and a remote name.  During
   signaling, the local name is sent as the SAII, the remote name as the
   TAII, and the AGI is null.  If two Attachment Circuits are to be
   connected by a PW, the local name of each must be the remote name of
   the other.

   Note that if the local name and the remote name are the same, the
   PWid FEC element can be used instead of the Generalized ID FEC
   element.


5.1.1.2. Single Sided Provisioning with Discovery

   In this model, each Attachment circuit must be provisioned with a
   local name.  The local name consists of a VPN-id (signaled as the
   AGI) and an Attachment Individual Identifier which is unique relative
   to the AGI.  If two Attachment circuits are to be connected by a PW,
   only one of them needs to be provisioned with a remote name (which of



Rosen                                                           [Page 9]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   course is the local name of the other Attachment Circuit).  Neither
   needs to be provisioned with the address of the remote PE, but both
   must have the same VPN-id.

   As part of an auto-discovery procedure, each PE advertises its <VPN-
   id, local AII> pairs.  Each PE compares its local <VPN-id, remote
   AII> pairs with the <VPN-id, local AII> pairs advertised by the other
   PEs.  If PE1 has a local <VPN-id, remote AII> pair with value <V,
   fred>, and PE2 has a local <VPN-id, local AII> pair with value <V,
   fred>, PE1 will thus be able to discover that it needs to connect to
   PE2.  When signaling, it will use "fred" as the TAII, and will use V
   as he AGI.  A null SAII is sent.

   The primary benefit of this provisioning model when compared to
   Double Sided Provisioning is that it enables one to move an
   Attachment Circuit from one PE to another without having to
   reconfigure the remote endpoint.


5.1.2. Signaling

   Signaling is as specified in section 4 above, with the addition of
   the following:

   When a PE receives a Label Mapping Message, and the TAI identifiers a
   particular Attachment Circuit which is configured to be bound to a
   point-to-point PW, then the following checks must be made.

   If the Attachment Circuit is already bound to a pseudowire (including
   the case where only one of the two LSPs currently exists), and the
   remote endpoint is not PE1, then PE2 sends a Label Release message to
   PE1, with a Status Code meaning "Attachment Circuit bound to
   different PE", and the processing of the Mapping message is complete.

   If the Attachment Circuit is already bound to a pseudowire (including
   the case where only one of the two LSPs currently exists, but the AI
   at PE1 is different than that specified in the AGI/SAII fields of the
   Mapping message) then PE2 sends a Label Release message to PE1, with
   a Status Code meaning "Attachment Circuit bound to different remote
   Attachment Circuit", and the processing of the Mapping message is
   complete.

   These errors could occur as the result of misconfigurations.








Rosen                                                          [Page 10]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


5.2. Virtual Private LAN Service

   In the VPLS application [L2VPN-REQ, VPLS], the Attachment Circuits
   can be though of as LAN interfaces which attach to "virtual LAN
   switches", or, in the terminology of [L2VPN-FW], "Virtual Switching
   Instances" (VSIs).  Each Forwarder is a VSI that attaches to a number
   of PWs and a number of Attachment Circuits.  The VPLS service
   [L2VPN-REQ, VPLS] requires that a single pseudowire be created
   between each pair of VSIs that are in the same VPLS.  Each PE device
   may have a multiple VSIs, where each VSI belongs to a different VPLS.


5.2.1. Provisioning

   Each VPLS must have a globally unique identifier, which we call a
   VPN-id.  Every VSI must be configured with the VPN-id of the VPLS to
   which it belongs.

   Each VSI must also have a unique identifier, but this can be formed
   automatically by concatenating its VPN-id with the IP address of its
   PE router.


5.2.2. Auto-Discovery

5.2.2.1. BGP-based auto-discovery

   The framework for BGP-based auto-discovery for a VPLS service is as
   specified in [BGP-AUTO], section 3.2.

   The AFI/SAFI used would be:

     - An AFI specified by IANA for L2VPN.  (This is the same for all
       L2VPN schemes.)

     - An SAFI specified by IANA specifically for a VPLS service whose
       pseudowires are set up using the procedures described in the
       current document.

   In order to use BGP-based auto-discovery as specified in [BGP-AUTO],
   the globally unique identifier associated with a VPLS must be
   encodable as an 8-byte Route Distinguisher (RD).  If the globally
   unique identifier for a VPLS is an RFC2685 VPN-id, it can be encoded
   as an RD as specified in [BGP-AUTO].  However, any other method of
   assigning a unique identifier to a VPLS and encoding it as an RD
   (using the encoding techniques of [RFC2547bis]) will do.

   Each VSI needs to have a unique identifier, which can be encoded as a



Rosen                                                          [Page 11]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   BGP NLRI.  This is formed by prepending the RD (from the previous
   paragraph) to an IP address of the PE containing the virtual LAN
   switch.

   (Note that it is not strictly necessary for all the VSIs in the same
   VPLS to have the same RD, all that is really necessary is that the
   NLRI uniquely identify a virtual LAN switch.)

   Each VSI needs to be associated with one or more Route Target (RT)
   Extended Communities, as discussed in [BGP-AUTO}.  These control the
   distribution of the NLRI, and hence will control the formation of the
   overlay topology of pseudowires that constitutes a particular VPLS.

   Auto-discovery proceeds by having each PE distribute, via BGP, the
   NLRI for each of its VSIs, with itself as the BGP next hop, and with
   the appropriate RT for each such NLRI.  Typically, each PE would be a
   client of a small set of BGP route reflectors, which would
   redistribute this information to the other clients.

   If a PE has a VSI with a particular RT, it can then receive all the
   NLRI which have that same RT, and from the BGP next hop attribute of
   these NLRI will learn the IP addresses of the other PE routers which
   have VSIs with the same RT.  The considerations of [RFC2547bis]
   section 4.3.3 on the use of route reflectors apply.

   If a particular VPLS is meant to be a single fully connected LAN, all
   its VSIs will have the same RT, in which case the RT could be (though
   it need not be) an encoding of the VPN-id.  If a particular VPLS
   consists of multiple VLANs, each VLAN must have its own unique RT.  A
   VSI can be placed in multiple VLANS (or even in multiple VPLSes) by
   assigning it multiple RTs.

   Note that hierarchical VPLS can be set up by assigning multiple RTs
   to some of the virtual LAN switches; the RT mechanism allows one to
   have complete control over the pseudowire overlay which constitutes
   the VPLS topology.


5.2.2.2. Radius-based auto-discovery

   [RADIUS-L2TP-VPLS] includes a proposal for using RADIUS-based auto-
   discovery.









Rosen                                                          [Page 12]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


5.2.3. Signaling

   It is necessary to create Attachment Identifiers which identify the
   VSIs.  Given that each VPLS has at most one VSI per PE, and that only
   one PW is permitted between any pair of VSIs, a VSI can be uniquely
   identified (relative to its PE) by the VPN-id of its VPLS.  Therefore
   the signaling messages can encode the VPN-id in the AGI field, and
   use the null values of the SAII and TAII fields.

   The VPN-id may be encoded as an [RFC2547bis] RD, in which case the
   AGI field consist of a length field of value 8, followed by the 8
   bytes of the RD.  If the VPN-id is an RFC2685 VPN-id, it should be
   encoded as an RD (as specified in [BGP-AUTO]), and then the RD should
   be carried in the AGI field.

   If the VPN-id is an alphanumeric name, the first byte of the AGI
   field (immediately following the length) will be 0x90.  This
   distinguishes it from any RD.  The alphanumeric name itself then
   follows.

   Note that it is not possible using this technique to set up more than
   one PW per pair of VSIs.


5.3. Colored Pools: Full Mesh of Point-to-Point VCs

   In the "Colored Pools" model of operation, each PE may contain
   several pools of Attachment Circuits, each pool associated with a
   particular VPN.  A PE may contain multiple pools per VPN, as each
   pool may correspond to a particular CE device.  It may be desired to
   create one pseudowire between each pair of pools that are in the same
   VPN; the result would be to create a full mesh of CE-CE VCs for each
   VPN.  (This application was originally suggested in [BGP-SIGNALING];
   we show here that it can be done with LDP-based signaling.)


5.3.1. Provisioning

   Each pool is configured, and associated with:

     - a set of Attachment Circuits; whether these Attachment Circuits
       must themselves be provisioned, or whether they can be auto-
       allocated as needed, is independent of and orthogonal to the
       procedures described in this document;







Rosen                                                          [Page 13]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


     - a "color", which can be thought of as a VPN-id of some sort;

     - a relative pool identifier, which is unique relative to the
       color.

   The pool identifier, and color, taken together, constitute a globally
   unique identifier for the pool.  Thus if there are n pools of a given
   color, their pool identifiers can be (though they do not need to be)
   the numbers 1-n.

   The semantics are that a pseudowire will be created between every
   pair of pools that have the same color, where each such pseudowire
   will be bound to one Attachment Circuit from each of the two pools.

   If each pool is a set of Attachment Circuits leading to a single CE
   device, then the layer 2 connectivity among the CEs is controlled by
   the way the colors are assigned to the pools.  To create a full mesh,
   the "color" would just be a VPN-id.

   Optionally, a particular Attachment Circuit may be configured with
   the relative pool identifier of a remote pool.  Then that Attachment
   Circuit would be bound to a particular pseudowire only if that
   pseudowire's remote endpoint is the pool with that relative pool
   identifier.  With this option, the same pairs of Attachment Circuits
   will always be bound via pseudowires.



5.3.2. Auto-Discovery

5.3.2.1. BGP-based auto-discovery

   The framework for BGP-based auto-discovery for a colored pool service
   is as specified in [BGP-AUTO], section 3.2.

   The AFI/SAFI used would be:

     - An AFI specified by IANA for L2VPN.  (This is the same for all
       L2VPN schemes.)

     - An SAFI specified by IANA specifically for a Colored Pool L2VPN
       service whose pseudowires are set up using the procedures
       described in the current document.

   In order to use BGP-based auto-discovery, the color associated with a
   colored pool must be encodable as both an RT (Route Target) and an RD
   (Route Distinguisher).  The globally unique identifier of a pool must
   be encodable as NLRI; the color would be encoded as the RD and the



Rosen                                                          [Page 14]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   pool identifier as a four-byte quantity which is appended to the RD
   to create the NLRI.

   Auto-discovery procedures by having each PE distribute, via BGP, the
   NLRI for each of its pools, with itself as the BGP next hop, and with
   the RT that encodes the pool's color.  If a given PE has a pool with
   a particular color (RT), it must receive, via BGP, all NLRI with that
   same color (RT).  Typically, each PE would be a client of a small set
   of BGP route reflectors, which would redistribute this information to
   the other clients.

   If a PE has a pool with a particular color, it can then receive all
   the NLRI which have that same color, and from the BGP next hop
   attribute of these NLRI will learn the IP addresses of the other PE
   routers which have pools switches with the same color.  It also
   learns the unique identifier of each such remote pool, as this is
   encoded in the NLRI.  The remote pool's relative identifier can be
   extracted from the NLRI and used in the signaling, as specified
   below.


5.3.2.2. Radius-based Auto-Discovery

   The use of Radius-based auto-discovery for the colored pool model of
   operation is for further study.


5.3.3. Signaling

   When a PE sends a Label Mapping message to set up a PW between two
   pools, it encodes the color as the AGI, the local pool's relative
   identifier as the SAII, and the remote pool's relative identifier as
   the TAII.

   When PE2 receives a Label Mapping message from PE1, and the TAI
   identifies to a pool, and there is already an pseudowire connecting
   an Attachment Circuit in that pool to an Attachment Circuit at PE1,
   and the AI at PE1 of that pseudowire is the same as the SAI of the
   Label Mapping message, then PE2 sends a Label Release message to PE1,
   with a Status Code meaning "Attachment Circuit bound to different
   remote Attachment Circuit".  This prevents the creation of multiple
   pseudowires between a given pair of pools.

   Note that the signaling itself only identifies the remote pool to
   which the pseudowire is to lead, not the remote Attachment Circuit
   which is to be bound to the the pseudowire.  However, the remote PE
   may examine the SAII field to determine which Attachment Circuit
   should be bound to the pseudowire.



Rosen                                                          [Page 15]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


5.4. Colored Pools: Partial Mesh

   The procedures for creating a partial mesh of pseudowires among a set
   of colored pools are substantially the same as those for creating a
   full mesh, with the following exceptions:

     - Each pool is optionally configured with a set of "import RTs" and
       "export RTs";

     - During BGP-based auto-discovery, the pool color is still encoded
       in the RD, but if the pool is configured with a set of "export
       RTs", these are are encoded in the RTs of the BGP Update
       messages, INSTEAD the color.

     - If a pool has a particular "import RT" value X, it will create a
       PW to every other pool which has X as one of its "export RTs".
       The signaling messages and procedures themselves are as in
       section 5.3.3



5.5. Distributed VPLS

   In Distributed VPLS ([L2VPN-FW], [DTLS], [LPE]), the VPLS
   functionality of a PE router is divided among two systems: a U-PE and
   an N-PE.  The U-PE sits between the user and the N-PE.  VSI
   functionality (e.g., MAC address learning and bridging) is performed
   on the U-PE.  A number of U-PEs attach to an N-PE.  For each VPLS
   supported by a U-PE, the U-PE  maintains a pseudowire to each other
   U-PE in the same VPLS.  However, the U-PEs do not maintain signaling
   control connections with each other.  Rather, each U-PE has only a
   single signaling connection, to its N-PE.  In essence, each U-PE-to-
   U-PE pseudowire is composed of three pseudowires spliced together:
   one from U-PE to N-PE, one from N-PE to N-PE, and one from N-PE to
   U-PE.

   Consider for example the following topology:














Rosen                                                          [Page 16]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003





           U-PE A-----|             |----U-PE C
                      |             |
                      |             |
                    N-PE E--------N-PE F
                      |             |
                      |             |
           U-PE B-----|             |-----U-PE D




   where the four U-PEs are in a common VPLS.  We now illustrate how PWs
   get spliced together in the above topology in order to establish the
   necessary PWs from U-PE A to the other U-PEs.

   There are three PWs from A to E. Call these A-E/1, A-E/2, and A-E/3.
   In order to connect A properly to the other U-PEs, there must be two
   PWs from E to F (call these E-F/1 and E-F/2), one PW from E to B (E-
   B/1), one from F to C (F-C/1), and one from F to D (F-D/1).

   The N-PEs must then splice these pseudowires together to get the
   equivalent of what the non-distributed VPLS signaling mechanism would
   provide:

     - PW from A to B: A-E/1 gets spliced to E-B/1.

     - PW from A to C: A-E/2 gets spliced to E-F/1 gets spliced to F-
       C/1.

     - PW from A to D: A-E/3 gets spliced to E-F/2 gets spliced to F-
       D/1.

   It doesn't matter which PWs get spliced together, as long as the
   result is one from A to each of B, C, and D.

   Similarly, there are additional PWs which must get spliced together
   to properly interconnect U-PE B with U-PEs C and D, and to
   interconnect U-PE C with U-PE D.

   One can see that distributed VPLS does not reduce the number of
   pseudowires per U-PE, but it does reduce the number of control
   connections per U-PE.  Whether this is worthwhile depends, of course,
   on what the bottleneck is.





Rosen                                                          [Page 17]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


5.5.1. Signaling

   The signaling to support Distributed VPLS can be done with the
   mechanisms described in this paper.  However, the procedures for VPLS
   (section 5.2.3) presuppose that, between a pair of PEs, there is only
   one PW per VPLS.  In distributed VPLS, this isn't so.  In the
   topology above, for example, there are two PWs between A and E for
   the same VPLS.  For distributed VPLS therefore, one cannot identify
   the Forwarders merely by using the VPN-id as the AGI, while using
   null values of the SAII and TAII.  Rather, the SAII and TAII must be
   used to identify particular U-PE devices.

   At a given N-PE, the directly attached U-PEs in a given VPLS can be
   numbered from 1 to n.  This number identifies the U-PE relative to a
   particular VPN-id and a particular PE.  (That is, to uniquely
   identify the U-PE, the N-PE, the VPN-id, and the U-PE number must be
   known.)

   As a result of configuration/discovery, each U-PE must be given a
   list of <j, IP address> pairs.  Each element in this list tells the
   U-PE to set up j PWs to the specified IP address.  When the U-PE
   signals to the N-PE, it sets the AGI to the proper-VPN-id, and sets
   the SAII to the PW number, and sets the TAII to null.

   In the above example, U-PE A would be told <3, E>, telling it to set
   up 3 PWs to E.  When signaling, A would set the AGI to the proper
   VPN-id, and would set the SAII to 1, 2, or 3, depending on which of
   the three PWs it is signaling.

   As a result of configuration/discovery, each N-PE must be given the
   following information for each VPLS:

     - A "Local" list: {<j, IP address>}, where each element tells it to
       set up j PWs to the locally attached U-PE at the specified
       address.  The number of elements in this list will be n, the
       number of locally attached U-PEs in this VPLS.  In the above
       example, E would be given the local list: {<3, A>, <3, B>},
       telling it to set up 3 PWs to A and 3 to B.

     - A local numbering, relative to the particular VPLS and the
       particular N-PE, of its U-PEs.  In the above example, E could be
       told that U-PE A is 1, and U-PE B is 2.

     - A "Remote" list:  {<IP address, k>}, telling it to set up k PWs,
       for each U-PE, to the specified IP address.  Each of these IP
       addresses identifies a N-PE, and k specifies the number of U-PEs
       at that N-PE which are in the VPLS.  In the above example, E
       would be given the remote list: {<2, F>}.  Since N-PE E has two



Rosen                                                          [Page 18]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


       U-PEs, this tells it to set up 4 PWs to N-PE F, 2 for each of its
       E's U-PEs.

   The signaling of a PW from N-PE to U-PE is based on the local list
   and the local numbering of U-PEs.  When signaling a particular PW
   from an N-PE to a U-PE, the AGI is set to the proper VPN-id, and SAII
   is set to null, and the TAII is set to the PW number (relative to
   that particular VPLS and U-PE).  In the above example, when E signals
   to A, it would set the TAII to be 1, 2, or 3, respectively, for the
   three PWs it must set up to A.  It would similarly signal three PWs
   to B.

   The LSP signaled from U-PE to N-PE is associated with an LSP from N-
   PE to U-PE in the usual manner, as specified in section 4.  A PW
   between a U-PE and an N-PE is known as a "U-PW".

   The signaling of a PW from N-PE to N-PE is based on the remote list.
   When signaling a particular PW from an N-PE to an N-PE, the AGI is
   set to the appropriate VPN-id.  The remote list specifies the number
   of PWs to set up, per local U-PE, to a particular remote N-PE.  If
   there are n such PWs, they are distinguished by the setting of the
   TAII, which will be a number from 1 to n inclusive.  The SAII is set
   to the local number of the U-PE.  In the above example, E would set
   up 4 PWs to F.  The SAII/TAII fields would be set to 1/1, 1/2, 2/1,
   and 2/2 respectively.  A PW between two N-PEs is known as an "N-PW".

   Each U-PW must be "spliced" to an N-PW.  This is based on the remote
   list.  If the remote list contains an element <i, F>, then i U-PWs
   from each local U-PE must be spliced to i N-PWs from the remote N-PE
   F.  It does not matter which U-PWs are spliced to which N-PWs, as
   long as this constraint is met.

   If an N-PE has more than one local U-PE for a given VPLS, it must
   also ensure that a U-PW from each such U-PE  is spliced to a U-PW
   from each of the other U-PEs.


5.5.2. Provisioning and Discovery

   Every N-PE must be provisioned with the set of VPLS instances it
   supports, a VPN-id for each one, and a list of local U-PEs for each
   such VPLS.  As part of the discovery procedure, the N-PE advertises
   the number of U-PEs for each VPLS.

   Auto-discovery (e.g., BGP-based) can be used to discover all the
   other N-PEs in the VPLS, and for each, the number of U-PEs local to
   that N-PE.  From this, one can compute the total number of U-PEs in
   the VPLS.  This information is sufficient to enable one to compute



Rosen                                                          [Page 19]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   the local list and the remote list for each N-PE.


5.5.3. Non-distributed VPLS as a sub-case

   A PE which is providing "non-distributed VPLS" (i.e., a PE which
   peforms both the U-PE and N-PE functions) can interoperate with N-
   PE/U-PE pairs that are providing distributed VPLS.  The "non-
   distributed PE" simply advertises, in the discovery procedure, that
   it has one local U-PE per VPLS.  And of course, the non-distributed
   PE does no splicing.

   If every PE in a VPLS is providing non-distributed VPLS, and thus
   every PE advertises itself as an N-PE with one local U-PE, the
   resultant signaling is exactly the same as that specified in section
   5.2.3 above, except that SAII and TAII values of 1 are used instead
   of SAII and TAII values of null.  (A PE providing non-distributed
   VPLS should therefore treat AII values of 1 the same as it treats AII
   values of null.)


5.5.4. Inter-Provider Application of Dist. VPLS Signaling

   Consider the following topology:


   PE A ---- Network 1 ----- Border ----- Border ----- Network 2 ---- PE B
                             Router 12    Router 21       |
                                                          |
                                                         PE C



   where A, B, and C are PEs in a common VPLS, but Networks 1 and 2 are
   networks of different  Service Providers.  Border Router 12 is
   Network 1's border router to network 2, and Border Router 21 is
   Network 2's border router to Network 1.  We suppose further that the
   PEs are not "distributed", i.e, that each provides both the U-PE and
   N-PE functions.

   In this topology, one needs two inter-provider pseudowires: A-B and
   A-C.

   Suppose a Service Provider decides, for whatever reason, that it does
   not want each of its PEs to have a control connection to any PEs in
   the other network.  Rather, it wants the inter-provider control
   connections to run only between the two border routers.




Rosen                                                          [Page 20]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   This can be achieved using the techniques of section 5.5, where the
   PEs behave like U-PEs, and the BRs behave like N-PEs.  In the example
   topology, PE A would behave like a U-PE which is locally attached to
   BR12; PEs B and C would be have like U-PEs which are locally attached
   to BR21; and the two BRs would behave like N-PEs.

   As a result, the PW from A to B would consist of three segments: A-
   BR12, BR12-BR21, and BR21-B.  The border routers would have to splice
   the corresponding segments together.

   This requires the PEs within a VPLS to be numbered from 1-n (relative
   to that VPLS) within a given network.


5.5.5. Splicing and the Data Plane

   Splicing two PWs together is quite straightforward in the MPLS data
   plane, as moving a packet from one PW directly to another is just a
   label replace operation on the PW label.  When a PW consists of two
   PWs spliced together, it is assumed that the data will go to the node
   where the splicing is being done, i.e., that the data path will
   include the control points.

   In some cases, it may be desired to have the data go on a more direct
   route from one "true endpoint" to another, without necessarily
   passing through the splice points.  This could be done by means of a
   new LDP TLV  carried in the LDP mapping message; call it the "direct
   route" TLV.  A direct route TLV would be placed in an LDP Label
   Mapping message by the LSP's "true endpoint".  The TLV would specify
   the IP address of the true endpoint, and would also specify a label,
   representing the pseudowire, which is assigned by that endpoint.
   When PWs are spliced together at intermediate control points, this
   TLV would simply be passed upstream.  Then when a frame is first put
   on the pseudowire, it can be given this pseudowire label, and routed
   to the true endpoint, thereby possibly bypassing the intermediate
   control points.















Rosen                                                          [Page 21]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


6. Security Considerations

   Each L2VPN service has its own set of security considerations, and
   each signaling mechanism used for L2VPN has its own set of security
   considerations.  The semantics of the identifiers used in the
   signaling protocols does not pose any additional security
   considerations.  The choice of provisioning model also does not
   impose any security considerations, except insofar as the associated
   auto-discovery and signaling procedures may have security
   considerations.


7. Acknowledgments

   Thanks to Dan Tappan, Ted Qian, Bruce Davie, Ali Sajassi, Wei Luo,
   Skip Booth, and Francois LeFaucheur for their comments, criticisms,
   and helpful suggestions.

   Thanks to Tissa Senevirathne, Hamid Ould-Brahim and Yakov Rekhter for
   discussing the auto-discovery issues.

   Thanks to Vach Kompella and Wei Luo for a continuing discussion of
   the proper semantics of the generalized identifiers.


8. References

   [BGP-AUTO] "Using BGP as an Auto-Discovery Mechanism for Network-
   based VPNs", Ould-Brahim et. al.,  draft-ietf-ppvpn-bgpvpn-auto-
   03.txt, Aug 2002.

   [BGP-SIGNALING] "Layer 2 VPNs over Tunnels", Kompella et. al.,
   draft-kompella-ppvpn-l2vpn-03.txt, Apr 2003

   [RADIUS-L2TP-VPLS] "Radius/L2TP Based VPLS", Heinanen, draft-
   heinanen-radius-l2tp-vpls-00.txt, Feb 2003

   [L2VPN-FW] "PPVPN L2 Framework", Andersson et. al., draft-ietf-
   ppvpn-l2-framework-03.txt, Mar 2003

   [L2VPN-REQ] "Service Requirements for Layer 2 Provider Provisioned
   Virtual Private Network Services", Augustyn, Serbest, et. al.,
   draft-augustyn-ppvpn-l2vpn-requirements-02.txt, Feb 2003

   [L2VPN-TERM] "PPVPN Terminology", Andersson, Madsen, draft-
   andersson-ppvpn-terminology-02.txt, Nov 2002

   [LDP] "LDP Specification", Andersson, et. al., RFC 3036, Jan 2001



Rosen                                                          [Page 22]


Internet Draft   draft-rosen-ppvpn-l2-signaling-03.txt          May 2003


   [LUO-L2TP] "L2VPN Signaling Using L2TPv3", Luo, draft-luo-l2tpext-
   l2vpn- signaling-01.txt, Feb 2003

   [PWE3-ARCH] "PWE3 Architecture", Bryant, Pate, et. al., draft-ietf-
   pwe3-arch-02.txt, Feb 2003

   [PWE3-CONTROL] "Pseudowire Setup and Maintenance using LDP", Martini,
   et. al., draft-ietf-pwe3-control-protocol-02.txt, Feb. 2003

   [PWE3-FR] "Framework for Pseudo Wire Emulation Edge-to-Edge ",
   draft-ietf=pwe3-framework-01.txt, May 2002

   [RFC2547bis], "BGP/MPLS VPNs", Rosen, Rekhter, et. al., draft-ietf-
   ppvpn-rfc2547bis-04.txt,  Apr 2003

   [RFC2685] "Virtual Private Networks Identifier", Fox, Gleeson,
   September 1999

   [RFC3036] "LDP Specification", January 2001

   [VPLS] "Transparent VLAN Services over MPLS", Laserre, et. al.,
   draft-lasserre-vkompella-ppvpn-vpls-04.txt, Mar 2003


9. Author's Information


   Eric C. Rosen
   Cisco Systems, Inc.
   250 Apollo Drive
   Chelmsford, MA, 01824

   E-mail: erosen@cisco.com


















Rosen                                                          [Page 23]