SPRING Working Group                                             T. Saad
Internet-Draft                                                 V. Beeram
Intended status: Informational                                  C. Barth
Expires: August 19, 2021                          Juniper Networks, Inc.
                                                            S. Sivabalan
                                                      Ciena Corporation.
                                                       February 15, 2021


            Segment-Routing over Forwarding Adjacency Links
                        draft-saad-sr-fa-link-03

Abstract

   Label Switched Paths (LSPs) set up in Multiprotocol Label Switching
   (MPLS) networks can be used to form Forwarding Adjacency (FA) links
   that carry traffic in those networks.  An FA link can be assigned
   Traffic Engineering (TE) parameters that allow other LSR(s) to
   include it in their constrained path computation.  FA link(s) can be
   also assigned Segment-Routing (SR) segments that enable the steering
   of traffic on to the associated FA link(s).  The TE and SR attributes
   of an FA link can be advertised using known protocols that carry link
   state information.  This document elaborates on the usage of FA
   link(s) and their attributes in SR enabled networks.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on August 19, 2021.

Copyright Notice

   Copyright (c) 2021 IETF Trust and the persons identified as the
   document authors.  All rights reserved.





Saad, et al.             Expires August 19, 2021                [Page 1]


Internet-Draft              SR over FA Links               February 2021


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Forwarding Adjacency Links  . . . . . . . . . . . . . . . . .   3
     3.1.  Creation and Management . . . . . . . . . . . . . . . . .   4
     3.2.  Link Flooding . . . . . . . . . . . . . . . . . . . . . .   4
     3.3.  Underlay LSP(s) . . . . . . . . . . . . . . . . . . . . .   5
     3.4.  State Changes . . . . . . . . . . . . . . . . . . . . . .   5
     3.5.  TE Parameters . . . . . . . . . . . . . . . . . . . . . .   5
     3.6.  Link Local and Remote Identifiers . . . . . . . . . . . .   6
   4.  Segment-Routing over FA Links . . . . . . . . . . . . . . . .   6
     4.1.  SR IGP Segments for FA  . . . . . . . . . . . . . . . . .   7
       4.1.1.  Parallel Adjacencies  . . . . . . . . . . . . . . . .   7
     4.2.  SR BGP Segments for FA  . . . . . . . . . . . . . . . . .   7
     4.3.  Applicability to Interdomain  . . . . . . . . . . . . . .   8
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   9
   6.  Security Considerations . . . . . . . . . . . . . . . . . . .   9
   7.  Acknowledgement . . . . . . . . . . . . . . . . . . . . . . .   9
   8.  Normative References  . . . . . . . . . . . . . . . . . . . .   9
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  10

1.  Introduction

   To improve scalability in Multi-Protocol Label Switching (MPLS)
   networks, it may be useful to create a hierarchy of LSPs as
   Forwarding Adjacencies (FA).  The concept of FA link(s) and FA-LSP(s)
   was introduced in [RFC4206].

   In Segment-Routing (SR), this is particularly useful for two main
   reasons.

   First, it allows the stitching of sub-path(s) so as to realize an
   end-to-end SR path.  Each sub-path can be represented by a FA link
   that is supported by one or more underlying LSP(s).  The underlying
   LSP(s) that support an FA link can be setup using different
   technologies- including RSVP-TE, LDP, and SR.  The sub-path(s), or FA
   link(s) in this case, can possibly interconnect multiple



Saad, et al.             Expires August 19, 2021                [Page 2]


Internet-Draft              SR over FA Links               February 2021


   administrative domains, allowing each FA link within a domain to use
   a different technology to setup the underlying LSP(s).

   Second, it allows shortening of a large SR Segment-List by
   compressing one or more slice(s) of the list into a corresponding FA
   TE link that each can be represented by a single segment- see
   Section 4.  Effectively, it reduces the number of segments that an
   ingress router has to impose to realize an end-to-end path.

   The FA links are treated as normal link(s) in the network and hence
   it can leverage existing link state protocol extensions to advertise
   properties associated with the FA link.  For example, Traffic-
   Engineering (TE) link parameters and Segment-Routing (SR) segments
   parameters can be associated with the FA link and advertised
   throughout the network.

   Once advertised in the network using a suitable protocols that
   support carrying link state information, such as OSPF, ISIS or BGP
   Link State (LS)), other LSR(s) in the network can use the FA TE
   link(s) as well as possibly other normal TE link(s) when performing
   path computation and/or when specifying the desired explicit path.

   Though the concepts discussed in this document are specific to MPLS
   technology, these are also extensible to other dataplane technologies
   - e.g.  SRv6.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

3.  Forwarding Adjacency Links

   FA Link(s) can be created and supported by underlying FA LSPs.  The
   FA link is of type point-to-point.  FA links may be represented as
   either unnumbered or numbered.  The nodes connected by an FA link do
   not usually establish a routing adjacency over the FA link.  When FA
   links are numbered with IPv4 addresses, the local and remote IPv4
   addresses can come out of a /31 that is allocated by the LSR that
   originates the FA-LSP.  For unnumbered FA link(s), other provisions
   may exist to exchange link identifier(s) between the endpoints of the
   FA.






Saad, et al.             Expires August 19, 2021                [Page 3]


Internet-Draft              SR over FA Links               February 2021


3.1.  Creation and Management

   In general, the creation/termination of an FA link and its FA-LSP is
   driven either via configuration on the LSR at the head-end of the
   adjacency, or dynamically using suitable North Bound Interface (NBI)
   protocol, e.g.  Netconf, gRPC, PCEP, etc.

   The following FA-LSP attributes may be configured, including:
   bandwidth and resource colors, and other constraints.  The path taken
   by the FA-LSP may be either computed by the LSR at the head-end of
   the FA-LSP, or externally by a PCE and furnished to the headend.

   The attributes of the FA link can be inherited from the underlying
   LSP(s) that induced its creation.  In general, for dynamically
   provisioned FAs, a policy-based mechanism may be needed to associate
   link attributes to those of the FA-LSPs.

   When the FA link is supported by bidirectional FA LSP(s), a pair of
   FA link(s) are advertised from each endpoint of the FA.  These are
   usually referred to as symmetrical link(s).

3.2.  Link Flooding

   Multiple protocols exist that can exchange link state information in
   the network.  For example, when advertising TE link(s) and their
   attribute(s) using OSPF and ISIS protocols, the respective extensions
   are defined in [RFC3630] and [RFC5305].  Also, when exchanging such
   information in BGP protocol, extensions for BGP link state are
   defined in [RFC7752] and [RFC8571].  The same protocol encodings can
   be used to advertise FA(s) as TE link(s).  As a result, the FA TE
   link(s) and other normal TE link(s) will appear in the TE link state
   database of any LSR in the network, and can be used for computing
   end-to-end TE path(s).

   When IGP protocols are used to advertise link state information about
   FA links, the FA link(s) can appear in both the TE topology, as well
   as the IGP topology.  The use of FA link in the IGP topology may
   result in undesirable routing loops.  A router SHOULD leverage
   exisitng mechanisms to exclude the FA link from the IGP Shortest Path
   First (SPF) computations, and to restrict its use within the TE
   topology for traffic engineered paths computation.

   For example, when using ISIS to carry FA link state information,
   [RFC5305] section 3 describes a way to restrict the link to the TE
   topology by setting the IGP link metric to maximum (2^24 - 1).
   Alternatively, when using OSPF, the FA link(s) can be advertised
   using TE Opaque LSA(s) only, and hence, strictly show up in the TE
   topology as described in [RFC3630] .



Saad, et al.             Expires August 19, 2021                [Page 4]


Internet-Draft              SR over FA Links               February 2021


3.3.  Underlay LSP(s)

   The LSR that hosts an FA link can setup the underlying LSP(s) using
   different technologies - e.g.  RSVP-TE, LDP, and SR.

   The FA link can be supported by one or more underlay LSP(s) that
   terminate on the same remote endpoint.  The underlay path(s) can be
   setup using different signaling technologies, e.g. using RSVP-TE,
   LDP, SR, etc.  When multiple LSP(s) support the same FA link, the
   attributes of the FA link can be derived from the aggregate
   properties of each of the underlying LSP(s).

3.4.  State Changes

   The state of an FA TE link reflects the state of the underlying LSP
   path that supports it.  The TE link is assumed operational and is
   advertised as long as the underlying LSP path is valid.  When all
   underlying LSP paths are invalidated, the FA TE link advertisement is
   withdrawn.

3.5.  TE Parameters

   The TE metrics and TE attributes are used by path computation
   algorithms to select the TE link(s) that a TE path traverses.  When
   advertising an FA link in OSPF or ISIS, or BGP-LS, the following TE
   parameters are defined:

   TE Path metrics:  the FA link advertisement can include information
      about TE, IGP, and other performance metrics (e.g. delay, and
      loss).  The FA link TE metrics, in this case, can be derived from
      the underlying path(s) that support the FA link by producing the
      path accumulative metrics.  When multiple LSP(s) support the same
      FA link, then the higher accumulative metric amongst the LSP(s) is
      inherited by the FA link.

   Resource Class/Color:  An FA link can be assigned (e.g. via
      configuration) a specific set of admin-groups.  Alternatively, in
      some cases, this can be derived from the underlying path affinity
      - for example, the underlying path strictly includes a specific
      admin-group.

   SRLGs:  An FA advertisement could contain the information about the
      Shared Risk Link Groups (SRLG) for the path taken by the FA LSP
      associated with that FA.  This information may be used for path
      calculation by other LSRs.  The information carried is the union
      of the SRLGs of the underlying TE links that make up the FA LSP
      path.  It is possible that the underlying path information might
      change over time, via configuration updates or dynamic route



Saad, et al.             Expires August 19, 2021                [Page 5]


Internet-Draft              SR over FA Links               February 2021


      modifications, resulting in the change of the union of SRLGs for
      the FA link.  If multiple LSP(s) support the same FA link, then it
      is expected all LSP(s) have the same SRLG union - note, that the
      exact paths need not be the same.

   It is worth noting, that topology changes in the network may affect
   the FA link underlying LSP path(s), and hence, can dynamically change
   the TE metrics and TE attributes of the FA links.

3.6.  Link Local and Remote Identifiers

   It is possible for the FA link to be numbered or unnumbered.
   [RFC4206] describes a procedure for identifying a numbered FA TE link
   using IPv4 addresses.

   For unnumbered FA link(s), the assignment and handling of the local
   and remote link identifiers is specified in [RFC3477].  The LSR at
   each end of the unnumbered FA link assigns an identifier to that
   link.  This identifier is a non-zero 32-bit number that is unique
   within the scope of the LSR that assigns it.  There is no a priori
   relationship between the identifiers assigned to a link by the LSRs
   at each end of that link.

   The FA link is a unidirectional and point-to-point link.  Hence, the
   combination of link local identifier and advertising node can
   uniquely identify the link in the TED.  In some cases, however, it is
   desirable to associate the forward and reverse FA links in the TED.
   In this case, the combination of link local and remote identifier can
   identify the pair of forward and reverse FA link(s).  The LSRs at the
   two end points of an unnumbered link can exchange with each other the
   identifiers they assign to the link.  Exchanging the identifiers may
   be accomplished by configuration, or by means of protocol extensions.
   For example, when the FA link is established over RSVP-TE FA LSP(s),
   then RSVP extensions have been introduced to exchange the FA link
   identifier in [RFC3477].  Other protocol extensions pertaining to
   specific link state protocols, and LSP setup technologies will be
   discussed in a separate document.

   If the link remote identifier is unknown, the value advertised is set
   to 0 [RFC5307].

4.  Segment-Routing over FA Links

   The Segment Routing (SR) architecture [RFC4206] describes that an IGP
   adjacency can be formed over a FA link - in which the remote node of
   an IGP adjacency is a non-adjacent IGP neighbor.





Saad, et al.             Expires August 19, 2021                [Page 6]


Internet-Draft              SR over FA Links               February 2021


   In Segment-Routing (SR), the adjacency that is established over a
   link can be assigned an SR Segment [RFC8402].  For example, the Adj-
   SID allows to strictly steer traffic on to the specific adjacency
   that is associated with the Adj-SID.

4.1.  SR IGP Segments for FA

   Extensions have been defined to ISIS [RFC8667] and OSPF [RFC8665] in
   order to advertise the the Adjacency-SID associated with a specific
   IGP adjacency.  The same extensions apply to adjacencies over FA
   link.  A node can bind an Adj-SID to an FA data-link.  The Adj-SID
   dictates the forwarding of packets through the specific FA link or FA
   link(s) identified by the Adj-SID, regardless of its IGP/SPF cost.

   When the FA link Adj-SID is supported by a single underlying LSP that
   is associated with a binding label or SID, the same binding label can
   be used for the FA link Adj-SID.  For example, if the FA link is
   supported by an SR Policy that is assigned a Binding SID B, the Adj-
   SID of the FA link can be assigned the same Binding SID B.

   When the FA link Adj-SID is supported by multiple underlying LSP(s)
   or SR Policies - each having its own Binding label or SID, an
   independent FA link Adj-SID is allocated and bound to the multiple
   underlying LSP(s).

4.1.1.  Parallel Adjacencies

   Adj-SIDs can also be used in order to represent a set of parallel FA
   link(s) between two endpoints.

   When parallel FA links are associated with the same Adj-SID, a
   "weight" factor can be assigned to each link and advertised with the
   Adj-SID advertised with each FA link.  The weight informs the ingress
   (or an SDN/orchestration system) about the load-balancing factor over
   the parallel adjacencies.

4.2.  SR BGP Segments for FA

   BGP segments are allocated and distributed by BGP.  The SR
   architecture [RFC8402] defines three types of BGP segments for Egress
   Peer Engineering (EPE): PeerNode SID, PeerAdj SID, and PeerSet SID.

   The applicability of each of the three types to FA links is discussed
   below:

   o PeerNode SID: a BGP PeerNode segment/SID is a local segment.  At
   the BGP node advertising, the forwarding semantics are:




Saad, et al.             Expires August 19, 2021                [Page 7]


Internet-Draft              SR over FA Links               February 2021


      *  SR operation: NEXT.

      *  Next-Hop: forward over any FA link associated with the segment
         that terminates on remote endpoint.

   o PeerAdj SID: a BGP PeerAdj segment/SID is a local segment.  At the
   BGP node advertising it, the forwarding semantics are:



      *  SR operation: NEXT.

      *  Next-Hop: forward over the specific FA link to the remote
         endpoint to which the segment is related.

   o PeerSet SID: a BGP PeerSet segment/SID is a local segment.  At the
   BGP node advertising it, the semantics are:



      *  SR operation: NEXT.

      *  Next-Hop: load-balance across any of the FA links to any remote
         endpoint in the related set.  The group definition is a policy
         set by the operator.

4.3.  Applicability to Interdomain

   In order to determine the potential to establish a TE path through a
   series of interconnected domains or multi-domain network, it is
   necessary to have available a certain amount of TE information about
   each network domain.  This need not be the full set of TE information
   available within each network but does need to express the potential
   of providing such TE connectivity.

   Topology abstraction is described in [RFC7926].  Abstraction allows
   applying a policy to the available TE information within a domain so
   to produce selective information that represents the potential
   ability to connect across the domain.  Thus, abstraction does not
   necessarily offer all possible connectivity options, but presents a
   general view of potential connectivity according to the policies that
   determine how the domain's administrator wants to allow the domain
   resources to be used.

   Hence, the domain may be constructed as a mesh of border node to
   border node TE FA links.  When computing a path for an LSP that
   crosses the domain, a computation point can see which domain entry
   points can be connected to which others, and with what TE attributes.



Saad, et al.             Expires August 19, 2021                [Page 8]


Internet-Draft              SR over FA Links               February 2021


5.  IANA Considerations

   This document has no IANA actions.

6.  Security Considerations

   TBD.

7.  Acknowledgement

   The authors would like to thank Peter Psenak for reviewing and
   providing valuable feedback on this document.

8.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3477]  Kompella, K. and Y. Rekhter, "Signalling Unnumbered Links
              in Resource ReSerVation Protocol - Traffic Engineering
              (RSVP-TE)", RFC 3477, DOI 10.17487/RFC3477, January 2003,
              <https://www.rfc-editor.org/info/rfc3477>.

   [RFC3630]  Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering
              (TE) Extensions to OSPF Version 2", RFC 3630,
              DOI 10.17487/RFC3630, September 2003,
              <https://www.rfc-editor.org/info/rfc3630>.

   [RFC4206]  Kompella, K. and Y. Rekhter, "Label Switched Paths (LSP)
              Hierarchy with Generalized Multi-Protocol Label Switching
              (GMPLS) Traffic Engineering (TE)", RFC 4206,
              DOI 10.17487/RFC4206, October 2005,
              <https://www.rfc-editor.org/info/rfc4206>.

   [RFC5305]  Li, T. and H. Smit, "IS-IS Extensions for Traffic
              Engineering", RFC 5305, DOI 10.17487/RFC5305, October
              2008, <https://www.rfc-editor.org/info/rfc5305>.

   [RFC5307]  Kompella, K., Ed. and Y. Rekhter, Ed., "IS-IS Extensions
              in Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 5307, DOI 10.17487/RFC5307, October 2008,
              <https://www.rfc-editor.org/info/rfc5307>.







Saad, et al.             Expires August 19, 2021                [Page 9]


Internet-Draft              SR over FA Links               February 2021


   [RFC7752]  Gredler, H., Ed., Medved, J., Previdi, S., Farrel, A., and
              S. Ray, "North-Bound Distribution of Link-State and
              Traffic Engineering (TE) Information Using BGP", RFC 7752,
              DOI 10.17487/RFC7752, March 2016,
              <https://www.rfc-editor.org/info/rfc7752>.

   [RFC7926]  Farrel, A., Ed., Drake, J., Bitar, N., Swallow, G.,
              Ceccarelli, D., and X. Zhang, "Problem Statement and
              Architecture for Information Exchange between
              Interconnected Traffic-Engineered Networks", BCP 206,
              RFC 7926, DOI 10.17487/RFC7926, July 2016,
              <https://www.rfc-editor.org/info/rfc7926>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

   [RFC8571]  Ginsberg, L., Ed., Previdi, S., Wu, Q., Tantsura, J., and
              C. Filsfils, "BGP - Link State (BGP-LS) Advertisement of
              IGP Traffic Engineering Performance Metric Extensions",
              RFC 8571, DOI 10.17487/RFC8571, March 2019,
              <https://www.rfc-editor.org/info/rfc8571>.

   [RFC8665]  Psenak, P., Ed., Previdi, S., Ed., Filsfils, C., Gredler,
              H., Shakir, R., Henderickx, W., and J. Tantsura, "OSPF
              Extensions for Segment Routing", RFC 8665,
              DOI 10.17487/RFC8665, December 2019,
              <https://www.rfc-editor.org/info/rfc8665>.

   [RFC8667]  Previdi, S., Ed., Ginsberg, L., Ed., Filsfils, C.,
              Bashandy, A., Gredler, H., and B. Decraene, "IS-IS
              Extensions for Segment Routing", RFC 8667,
              DOI 10.17487/RFC8667, December 2019,
              <https://www.rfc-editor.org/info/rfc8667>.

Authors' Addresses

   Tarek Saad
   Juniper Networks, Inc.

   Email: tsaad@juniper.net





Saad, et al.             Expires August 19, 2021               [Page 10]


Internet-Draft              SR over FA Links               February 2021


   Vishnu Pavan Beeram
   Juniper Networks, Inc.

   Email: vbeeram@juniper.net


   Colby Barth
   Juniper Networks, Inc.

   Email: cbarth@juniper.net


   Siva Sivabalan
   Ciena Corporation.

   Email: ssivabal@ciena.com



































Saad, et al.             Expires August 19, 2021               [Page 11]