Network Working Group S. Dry
F. Calabria
I.Y Fung
Internet Draft Cisco
M. Napierala
AT&T
Y. Kamite
NTT Corporation
Expires: February 2008 August 16, 2007
Multicast VPN Scalability Benchmarking
draft-sdry-bmwg-mvpnscale-02.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that
any applicable patent or other IPR claims of which he or she is
aware have been or will be disclosed, and any of which he or she
becomes aware will be disclosed, in accordance with Section 6 of
BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on February 16, 2008.
Abstract
Dry, et al. Expires February 16, 2008 [Page 1]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Multicast VPN (MVPN) is a service deployed by VPN service providers
to enable their customers to use IP multicast applications over VPNs.
With the increased popularity the scalability of deploying such a
service is becoming of a great interest. This document defines
standard metric and test methodology for characterizing and comparing
control plane MVPN scalability of Provider Edge (PE) devices that
implement MVPN service.
Table of Contents
1 Introduction...................................................3
2 Document Scope.................................................4
3 Terminology....................................................5
4 Key Words to Reflect Requirements..............................7
5 MVPN Metric Definition.........................................7
6 Test Environment...............................................8
6.1 Test Topologies..........................................9
6.2 Unicast Control Plane Setup..............................9
6.3 Multicast Control Plane Setup...........................10
6.4 Data Traffic Characteristics............................11
6.5 Test Apparatus Considerations...........................11
6.6 Considerations for distributed architecture platforms...12
7 Test Categories, Stimulus and Execution Methodology...........12
7.1 Steady State Testing Execution Methodology..............13
7.2 Failure Recovery Testing Execution Methodology..........14
8 Results Content and Reporting Format..........................15
8.1 Steady State Testing....................................15
8.2 Failure Recovery Testing................................16
9 Test Cases....................................................17
9.1 ''Empty'' MVPNs Scale.....................................18
9.2 PIM Enabled VPN C-Interfaces Scale......................20
9.3 PIM Neighborships Scale.................................22
9.4 Default MDT's (MI-PMSI's) PIM P-Instance Mroutes Scale..25
9.5 PIM C-instances Mroutes Scale...........................27
9.6 PIM C-Instances OIF Scale...............................30
9.7 Joined S-PMSI (Data MDT) Scale..........................32
9.8 Sourced S-PMSI (Data MDT) Scale.........................35
9.9 Data MDT (S-PMSI) Reuse.................................37
9.10 PIM C-instances J/P Suppression Effectiveness...........39
9.11 Additional Tests and Considerations for Devices Lacking
''Efficient'' Join/Prune Suppression............................42
9.12 Scale of mVPNs spanning large number of PEs.............43
9.13 Scale of mVPNs with larger amount of state..............46
9.14 Scale of ''average'' size mVPNs...........................48
9.15 S-PMSI Switching Delay..................................50
9.16 Convergence of C-Instance PIM Joins.....................51
Dry, et al. Expires February 16, 2008 [Page 2]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
9.17 Effect of Co-locating C-RPs on a PE.....................53
10 Security Considerations....................................55
11 IANA Considerations........................................55
12 Acknowledgments............................................55
13 References.................................................56
13.1 Normative References....................................56
13.2 Informative References..................................56
Author's Addresses...............................................57
Intellectual Property Statement..................................57
Disclaimer of Validity...........................................58
Copyright Statement..............................................58
Acknowledgment...................................................58
1 Introduction
Multicast Virtual Private Network (MVPN) is a service offered by
BGP/MPLS VPN service providers, that provides a way for IP multicast
traffic to travel from one customer site to another. [L3VPN-MCAST] is
the framework describing how various protocols fit together to enable
such functionality.
With the increased popularity, the scalability of deploying MVPN is
becoming of a great interest. There is, however, no standard method
defined to measure and compare different implementations. This
document proposes a MVPN scalability metric and methodology for
testing and comparing control plane MVPN scalability of (Provider
Edge) PE devices in a standardized way.
Before describing the detailed test methodology, it is important to
review the key factors that impact the scalability of MVPN
deployments:
o The MVPN Metric is 14-tuple comprised of a set of variables that
indicate the overall scalability capabilities of a PE device
implementation in various dimensions. MVPN scalability is multi-
dimensional and can not be quantified with single parameter, thus
defining such a metric set is necessary. MVPN Metric will be
defined in section 5. The remaining of this document focuses on a
methodology that characterizes different dimensions of MVPN
Metric.
o MVPN design and operational choices (such as selection of PIM
protocol variant or extent of S-PMSI (data MDT) usage) SP makes,
impact the overall MVPN scalability of a PE device. Typically
there is a tradeoff between optimality and scalability. More
details on these choices with their tradeoffs are discussed in
Dry, et al. Expires February 16, 2008 [Page 3]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
[MVPN-DEPLOY] and [L3VPN-MCAST]. In this document design choices
most suitable for a goal of any given test case will be used which
may not necessarily be the same as recommended design choice for a
realistic deployment.
o MVPN is a service that is never deployed in isolation as it
requires underlying unicast VPN offering. Typically SPs add MVPN
service on PE devices that are already deployed and are providing
a large number of other services such as unicast L3VPNs, L2VPNs,
internet access, etc. Therefore, when considering MVPN scalability
in realistic deployments one needs to take into consideration the
level to which PE resources are already utilized and the available
headroom amount remaining. In this document it will be assumed
that MVPN service is deployed as an addition of a ''minimized''
unicast control plane.
o MVPN Scalability of a PE device is different when the system is
subjected to different stimuli. For example overall scalability
achieved in steady state can be typically higher than when the
system is subjected to a network and/or device specific failures.
In this document a limited set of mandatory test stimuli will be
defined.
2 Document Scope
In IETF currently there are multiple proposals on architectures and
protocols for implementing MVPN service, as documented in [L3VPN-
MCAST]. The scope of this document is on benchmarking MVPN
scalability for the MVPN architecture described in [L3VPN-MCAST]
which uses PIM protocol for both PE-PE transmission of C-Multicast
routing information and to create 'tunnels' that instantiate
Multidirectional Inclusive P-Multicast Service Interfaces (MI-PMSIs)
and Selective P-Multicast Service Interfaces (S-PMSIs). The same
architecture is also described in [ROSEN-8] which is obsoleted by
[L3VPN-MCAST]. In the rest of the document this architecture will be
referred to as a ''ROSEN-8'' architecture.
In addition, test methodology and a good portion of the test cases
from this document can be used to assess a great deal but not all of
scalability aspects of other MVPN architectures from [L3VPN-MCAST].
Thus, it can easily be used as a base for any future supplemental
benchmarking documents addressing other MVPN architectures. We
explicitly identified text applicable to all architectures from
[L3VPN-MCAST].
Dry, et al. Expires February 16, 2008 [Page 4]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Scope of this document is to address comparison between different
implementations of the same MVPN architecture, and not between
different MVPN architectures defined in [L3VPN-MCAST].
This document proposes a MVPN metric and a test methodology to
compare the MVPN control plane scalability of PE devices in a
standardized way. In contrast, forwarding performance benchmarking is
not within the scope of this document.
Test methodology defines a standard set of test cases, their test
execution procedures, results content and reporting format. Standard
test environment is also defined for each test case.
Test cases 9.1-9.11 focus on determining implementation limits
individually for each of the key MVPN variables in a standard way.
Test cases (9.12-9.17) focus on determining implementation limits for
combination of all MVPN variables and will be helpful to operators
with network engineering for their deployments. Choices of values of
variables in test cases 9.12-9.17 were made using information from
the MVPN requirements survey conducted as part of [MVPN-REQ].
Each test case addresses following two major testing types:
. Steady State Testing: Device Under Test (DUT) and network as a
whole are not subject to any failure stimulus/control plane events.
. Failure Recovery Testing: DUT and or network components are subject
to different failure stimulus that introduces one or more control
plane instability events.
In this document limited set of mandatory test stimuli is also
defined.
Note that the deployment of MVPN also consumes resources on P devices
in support of creation and maintenance of PMSIs / MDTs (Multicast
Distribution Trees). But, since MVPN functionality does not reside on
P and CE routers, they are beyond the scope of this document.
3 Terminology
DUT (Device Under Test) term will be used interchangeably with MVPN
PE device.
We will use term ''MVPN architecture'' to describe any specific subset
of protocols and procedures from [L3VPN-MCAST] that can enable MVPN
Dry, et al. Expires February 16, 2008 [Page 5]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
functionality on PE device. In contrast, we will use term ''MVPN
implementations'' to describe practical implementations of such ''MVPN
architectures''.
VPN related terms used in this document are defined in RFC4364 and
RFC2547bis. MVPN related terms used in this document are defined in
[L3VPN-MCAST].
PIM (Protocol Independent Multicast) related terms are defined in
RFC4601.
For the reader's convenience, here is review of some key terms used
in this document:
MVPN (Multicast Virtual Private Network): VPN that supports transport
of IP multicast traffic from one site to another.
PMSI (P-Multicast Service Interface): A PMSI is a conceptual
"overlay" on the P network with the following property: a PE in a
given MVPN can give a packet to the PMSI, and the packet will be
delivered to some or all of the other PEs in the MVPN, such that any
PE receiving such a packet will be able to tell which MVPN the
packet belongs to.
MI-PMSI (Multidirectional Inclusive PMSI): PMSI which enables ANY PE
attaching to a particular MVPN to transmit a message such that it
will be received by EVERY other PE attaching to that MVPN.
S-PMSI (Selective PMSI): PMSI which enables PE attaching to a MVPN to
transmit a message such that it will be received by subset of other
PEs attaching to that same MVPN.
Default MDT (Default Multicast Distribution Tree): Multicast
distribution tree through the SP core that connects ALL PEs which
belong to given MVPN. This is [ROSEN-8] terminology for transport
service of MI-PMSIs. In this document we will use this term
interchangeably with MI-PMSI.
Data MDT (Data Multicast Distribution Tree): Multicast distribution
tree through the SP core that delivers VPN data traffic for a
particular multicast group only to those PE routers which are on the
path to receivers of that group. This is [ROSEN-8] terminology for
transport service of S-PMSIs. In this document we will use this term
interchangeably with S-PMSI.
Dry, et al. Expires February 16, 2008 [Page 6]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
ASM (Any Source Multicast): Multicast service model in which a
receiver subscribes to a multicast group to receive traffic sent to
the group by any source.
SSM (Source Specific Multicast): Multicast service model in which a
receiver subscribes to a multicast group to receive traffic sent to
the group by the specific source.
Mroute: Multicast route. Term ''state'' will used interchangeable with
''mroute'' and ''multicast route''.
''ROSEN-8'' architecture: architecture described in [L3VPN-MCAST] which
uses PIM protocol for both PE-PE Transmission of C-Multicast Routing
and to create 'tunnels' that instantiate Multidirectional Inclusive
P-Multicast Service Interfaces (MI-PMSIs) and Selective P-Multicast
Service Interfaces (S-PMSIs). This is a same as architecture
described in [ROSEN-8].
4 Key Words to Reflect Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119
[Br97]. RFC 2119 defines the use of these key words to help make the
intent of standards track documents as clear as possible. While this
document uses these keywords, this document is not a standards track
5 MVPN Metric Definition
MVPN control plane scalability of PE device can not be described as a
single parameter but it requires a set of variables. We call such a
set ''MVPN Metric'' and define it further in this section.
When providing scalability capabilities of a PE device one MUST
provide values for all of the MVPN metric variables that were used
during the test. For example, one should never claim that a PE device
supports X number of MVPNs without disclosing the values of other
MVPN Metric variables.
The MVPN Metric is defined as a tuple of the following 14 variables:
Variables Applicable to all MVPN architectures
Dry, et al. Expires February 16, 2008 [Page 7]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
1. Num_mVPN: Number of multicast VPN routing instances configured on
DUT that have MI-PMSI (default MDT) active and forwarding.
2. Num_MC_C_ints: Number of PIM C-interfaces on DUT
3. Num_PIM_C_neigh: Total number of PIM neighbors in PIM C-instances
across all mVPNs on DUT not including any PIM neighborships
established over MI-PMSIs.
4. Num_*G_C: Total number of (*,G) multicast routes across all MVPNs
on DUT capable of forwarding and created by PIM C-instances.
5. Num_SG_C: Total number of (S,G) multicast routes across all MVPNs
on DUT capable of forwarding and created by PIM C-instances.
6. Num_OIF_C: Total number of OIFs on DUT across all multicast routes
created by PIM C-instances.
7. Num_SPMSI_Src: Total number of data MDTs (S-PMSIs) across all mVPNs
on DUT that are sourced by DUT.
8. Num_SPMSI_Rx: Total number of data MDTs (S-PMSIs)across all mVPNs
on DUT for which DUT is a receiver.
9. Num_SPMSI_SrcFlows: Total number of C-instance (S,G) flows across
all mVPNs on DUT that are mapped to Num_SPMSI_Src.
10. Num_SPMSI_RxFlows: Total number of C-instance (S,G) flows
across all mVPNs on DUT that are mapped to Num_SPMSI_Rx.
Additional variables applicable to ''ROSEN-8'' architecture:
1. Num_PIM_MI_PMSI_neigh: Total number of PIM neighbors in PIM C-
instances across all mVPNs on DUT established over MI-PMSIs.
2. Num_*G_P: Total number of (*,G) multicast routes on DUT capable of
forwarding and created by PIM P-instance on DUT.
3. Num_SG_P: Total number of (S,G) multicast routes on DUT capable of
forwarding and created by PIM P-instance.
4. Num_OIF_P: Total number of OIFs (outgoing interfaces) on DUT
across all multicast routes created by PIM P-instance.
6 Test Environment
Note that all considerations in this sections except for ones related
to PIM P-instances for default (MI-PMSI) and data MDTs (SI-PMSI) are
applicable to all MVPN architectures defined in [L3VPN-MCAST].
Dry, et al. Expires February 16, 2008 [Page 8]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
All protocols involved MUST be deployed with default timers as
specified by their corresponding RFC / standards.
6.1 Test Topologies
___________ _________ ________ ________ ___________
/ \ / \ / \ / \ / \
| Test |A1 | (DUT) |D2 | RR |B2 | |B4 | Test |
| Apparatus |====| PE1 |====| P |====| PE2 |====| Apparatus |
| | D1| | B1| | B3| | A2| |
\___________/ \_________/ \________/ \________/ \___________/
||
|| _____________
|| / \
|| A3| Test |
++======================| Apparatus |
| (Emulating |
|_PE routers)_|
\_____________/
Figure 1. Test Topology 1
Legend:
D1 (DUT's C-facing interface): DUT's interface that connects to
customer premise router (C-router).
D2 (DUT's P-facing interface): DUT's interface that connects to SP's
core router (P-router).
RR/P (Route Reflector/P-router): single router that will be
performing roles of both P-router and route reflector
PE2: Will also be referred to as Remote PE and is the router
performing PE functionality to assist with evaluation of DUT PE
router.
6.2 Unicast Control Plane Setup
All P facing interfaces MUST use OSPF as IGP. This requirement is
made to provide a standard way to compare end to end convergence
times which depend on the underlying unicast protocol. Only a minimum
number of IGP routes required to establish connectivity should be
seen on the DUT.
All PE routers in the topology including the DUT and emulated PE's
MUST have one iBGP peer to the Route Reflector. DUT SHOULD NOT have
any additional iBGP peering. Only the minimum number of VPNv4 iBGP
Dry, et al. Expires February 16, 2008 [Page 9]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
routes required to establish site to site VPN connectivity should be
imported on the DUT. There SHOULD NOT be any internet/ipv4 routes
seen on the DUT.
A DUT MUST use static unicast routing on all C facing VPN interfaces.
Only the minimum number of static routes required to establish end to
end connectivity should be seen on the DUT. No dynamic unicast
routing protocol is used in order to minimize processing overhead.
6.3 Multicast Control Plane Setup
In any given test, all MI-PMSI (default MDT) groups MUST use the same
multicast routing protocol variant. Different tests may require
different protocol variants for MI-PMSI (default MDT) groups, so
refer to individual test cases for the appropriate multicast
configuration. In any test case where ASM (Any Source Multicast) mode
of PIM-SM (Protocol Independent Multicast - Sparse mode) is the
multicast routing protocol used for MI-PMSI (default MDT), a DUT
SHOULD NOT be the RP (Rendezvous Point). Also dynamic RP discovery
protocols SHOULD NOT be used for default MDT groups.
For S-PMSI (data MDT) groups PIM-SSM (Source Specific Multicast)
routing protocol MUST be used.
Sources emulated by test apparatus ports that are physically directly
connected to DUT (port A1 in Figures 1 and 2) not have IP address
from DUT's connected subnets, i.e. the DUT MUST not be the first hop
router.
For consistency, it is recommended for test apparatus ports that are
physically directly connected to DUT (port A1 in Figures 1 and 2) not
to use IGMP protocol to emulate multicast receivers. Instead PIM
protocol must be used, i.e. the DUT should not be the last hop
router.
As an exception to previous paragraph it may exist specific network
design requirement to deploy IGMP receivers connected directly to the
DUT in which case test results MUST specify number of C-interfaces
with IGMP receivers. Regardless the IGMP protocol variant to be
deployed (IGMPV2 / V3); receivers MUST be emulated by the test
apparatus and NOT defined on the DUT in the form of static group
reports. Test apparatus MUST be capable to emulate an IGMP Host or
Querier and set a maximum Timer Interval between messages of 1/10th
of a second.
Dry, et al. Expires February 16, 2008 [Page 10]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
6.4 Data Traffic Characteristics
For every C-instance multicast route there MUST be traffic flow
associated with it and forwarded by DUT.
All C-instance flows SHOULD be transmitted with the same traffic rate
and packet size.
As the focus of this document is on the control plane scalability and
not on forwarding performance the data rate and packet size of
traffic flows can be chosen by user but it MUST be reported in the
test results. However it is suggested to use 10% of ''idle system''
throughput [RFC1242] so that it can be easily detected if hardware
forwarding platforms start forwarding in software and at the same
time in case of software forwarding platforms there will be enough
processor headroom left for control plane scaling. By ''idle system''
we refer to system with all of MVPN metric variables minimized and
single VPN traffic flow in each direction.
As an additional requirement, the reader of this document may also be
interested in analyzing the ''impact'' that high traffic rate may have
on the control plane. This would be of interest mostly for software
forwarding platforms. For this specific requirement additional test
cases SHOULD be performed increasing the rate of multicast traffic to
20%, 50% and 90% of ''idle system'' throughput [RFC1242].
6.5 Test Apparatus Considerations
Different test tools must generate PIM protocol control messages in a
consistent way since they are directly connected to the DUT.
The following MUST be implemented on all PIM sessions on the test
apparatus:
1) PIM Join/Prune aggregation MUST be utilized and set such that 80
PIM J/P messages are aggregated in each PDU
2) PIM Join/Prune aggregated PDUs MUST be sent at 10 PDUs/sec rate
per PIM session, i.e. this translates to maximum of
80*10*60=48,000 state per minute.
3) PIM Register messages MUST be sent at 100 PDUs/sec rate.
Dry, et al. Expires February 16, 2008 [Page 11]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
4) In order to closer mimic realistic deployments test apparatus
SHOULD send all control plane messages in 10 equal size batches
with at least 5 seconds between each batch.
6.6 Considerations for distributed architecture platforms
To fairly evaluate platforms with distributed architectures one MUST
utilize at least two C-facing line cards in the system.
Configuration MUST be such that total number of mVPNs is distributed
evenly across multiple line cards.
7 Test Categories, Stimulus and Execution Methodology
Note that everything in this section except for verification of PIM
neighborships over MI-PMSI is applicable to all MVPN architectures
defined in [L3VPN-MCAST].
Each test case specified in section 9 MUST be executed for steady
state and for each of six mandatory failure stimulus listed below.
Optionally one can use methodology defined in this document for
additional stimulus.
Mandatory failure stimulus:
1) DUT Power Cycle: Physical power cycle of DUT. All convergence
times MUST be measured from the time DUT's power is turned back
on. This time instance will be referred to as Tf (the time of
failure recovery action) for this failure stimulus.
2) Main Processor Card Switchover: Physical removal of the active
main processor card in the redundant system. All convergence times
should be measured from the time active processor card is
physically disconnected from the chassis (Tf). This stimulus can
be omitted only for platforms that do not support redundant main
processor cards.
3) P-facing Line Card OIR (online insertion and removal): Physical
removal and insertion of P-facing line card. Time between removal
and insertion SHOULD be at least 300 seconds. All convergence
times should be measured from the time line card is physically
inserted into chassis (Tf).
4) C-facing Line Card OIR: Physical removal and insertion of C-facing
line card. Time between removal and insertion SHOULD be at least
300 seconds. All convergence times should be measured from the
time line card is physically re-inserted into chassis (Tf).
Dry, et al. Expires February 16, 2008 [Page 12]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
5) P-facing Link Flap: Physical removal and insertion of the cable
from P router side that is connected to P-facing interface of DUT.
Time between removal and insertion SHOULD be at least 300 seconds.
All convergence times should be measured from the time cable is
physically re-inserted (Tf).
6) C-facing Link Flap: Physical removal and insertion of the cable
from test apparatus side that is connected to C-facing interface
of DUT. Time between removal and insertion SHOULD be at least 300
seconds. All convergence times should be measured from the time
cable is physically re-inserted (Tf).
Since the test execution methodology is similar for all test cases we
will describe it here for both steady state and failure recovery
testing. Any deviation from this will be specified per test case in
section 9.
Multiple iterations of each test are required to determine maximum
value for certain set of variables. A single iteration will be
referred to as a ''Test Case Instance''.
7.1 Steady State Testing Execution Methodology
The following test execution procedure MUST be used for all Test Case
Instances during steady state testing of each test case defined in
section 9 of this document:
1) Ensure the testbed is setup according to Test Setup instructions
of individual test case
2) All Tunnel interfaces MUST be operational and MI-PMSIs (default
MDTs) required by the test case MUST be built as expected.
Verification can be done by DUT internal tools.
3) All real and emulated PE devices required by test cases MUST
have all C-instance PIM neighborships (including over MI-PMSIs)
operational in both directions. Verification MUST be done by
both external test apparatus and DUT internal tools.
4) All destination test apparatus ports configured to receive
multicast traffic should join all configured multicast groups.
5) All source test apparatus ports configured to transmit multicast
traffic should start transmitting to all multicast groups.
6) All multicast traffic MUST be received at all expected
destination test ports without any packet drops. This MUST be
Dry, et al. Expires February 16, 2008 [Page 13]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
verified using external test apparatus. If this state can not be
reached within 10 minutes of execution of step 5, continue to
next test case instance with reduced value of scaled variable/s
.
7) After state in previous step is reached wait 10 minutes and
start collecting data for this test instance required by
individual test case. This time instance is considered steady
state.
8) If any one of following conditions are reached continue to next
test case instance with reduced value of scaled variable/s:
o 100% utilization of system resources (memory, processor,
etc.)
o Failing of any of test case specific criteria or criteria in
steps 1-6 above
The number of Test Case Instances per test case is left to
tester's discretion. However, it is DESIRABLE to have results for
at least 5 test case instances. Having a range of values will help
in variable's characterization. The characterization of a variable
cannot be achieved with only one test case instance result.
7.2 Failure Recovery Testing Execution Methodology
The following test execution procedure MUST be used for all Test Case
Instances during failure recovery testing of each test case defined
in section 9 of this document:
1) Execute steps 1-6 from section 7.1
2) After steady state in previous step is reached wait 10 minutes
to initiate one of mandatory failure stimulus listed in section
7. Note the time of failure recovery action (Tf) as displayed by
the external test apparatus that is measuring the received
multicast traffic.
3) Using the external test apparatus note the time when THE FIRST
multicast packet has been received on at least ONE of expected
ports. Refer to this time instance as Tre for the first such
encapsulated packet and Trd for the first such decapsulated
packet.
4) Using the external test apparatus note the time when ALL
multicast traffic has been received on ALL expected ports, i.e.
Dry, et al. Expires February 16, 2008 [Page 14]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
it has returned to the same initial rate (in pps). Refer to this
time instance Trall.
5) After state in previous step is reached execute steps 2-3 from
7.1.
6) If all data verified in step 5 is the same as before failure
wait 10 minutes and start collecting data for this test instance
required by each individual test case
7) If any one of following conditions are reached continue to next
test case instance with reduced value of scaled variable/s:
a. Value of MVPN metric in steady state reached after failure
stimuli (step 6 above) is not the same as in original
steady state.
b. Multicast latency [RFC2432] averaged over all C-instance
multicast flows in steady state after failure recovery
stimuli is more than 10% larger than in original steady
state
c. Failing of any of test case specific criteria or criteria
in steps 1-6 above
The number of Test Case Instances per test case is left to
tester's discretion. However, it is DESIRABLE to have results for
at least 5 test case instances. Having a range of values will help
in variable's characterization. The characterization of a variable
cannot be achieved with only one test case instance result.
8 Results Content and Reporting Format
Note that everything in this section except for ''MI-PMSI PIM
neighborhsip convergence time'' is applicable to all MVPN
architectures defined in [L3VPN-MCAST].
8.1 Steady State Testing
For steady state portion of testing for each test case the following
results MUST be included in the test case report:
1. Maximum value achieved for variables requested to be varied in
individual test case
Dry, et al. Expires February 16, 2008 [Page 15]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
2. Values of MVPN Metric variables in the test instance in which item
1 of this report was achieved. The MVPN Metric as defined in
section 5 of this document MUST be used
3. Forwarding rate(in pps)[RFC2285] and packet sizes (in bytes) of all
flows in encapsulation direction at DUT
4. Forwarding rate(in pps)[RFC2285] and packet sizes (in bytes) of all
flows in decapsulation direction at DUT
5. Multicast Latency [RFC2432]averaged over all C-instance multicast
flows in encapsulation direction
6. Multicast Latency [RFC2432]averaged over all C-instance multicast
flows in decapsulation direction
7. Utilization of all processors in the system including the main
processor and line card processors where applicable. A description
of the way processor utilization is measured SHOULD be included in
the report.
8. Utilization of all relevant DUT memory components including the
main route processor memory and line cards where applicable.
9. Utilization of any relevant hardware components where applicable
10. Any deviations in DUT configuration from the configuration
defined in this document.
11. Any deviations in test execution procedure
It is DESIRABLE to include in the report items 1-9 above for all
optional test case instances executed, where instead of maximum value
achieved one would report tested value for each test case instance.
8.2 Failure Recovery Testing
In addition to data included in steady state reports defined in the
previous section the following MUST be included in the result report
of each failure recovery test case:
1. The worst case end to end traffic convergence time (Trall-Tf)
2. The best case end to end traffic convergence time ((Tre-Tf) for
encapsulation and (Trd-Tf) for decapsulation)
Note: Determination of whether all multicast flows had recovered to
the original traffic rate MUST be made by external test tools and
not by any available tools internal to the DUT or other routers in
the test topology.
Dry, et al. Expires February 16, 2008 [Page 16]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
It is DESIRABLE to include:
1. A graph from all test tool ports showing transmitted and received
packet rate starting from 60 seconds prior to failure action to 60
seconds after all multicast flows had recovered to the traffic rate
they had prior to the failure.
2. The best case MI-PMSI PIM neighborship convergence time: time
interval from instance Tf to instance when the first C-instance PIM
neighbor across one of MI-PMSIs comes up on both DUT and
neighboring device (i.e. ''bi-directional'' neighborships are
established).
3. The worst case MI-PMSI PIM neighborship convergence time: time
interval from instance Tf to instance when all expected C-instance
PIM neighbors across one of MI-PMSIs comes up on both DUT and
neighboring device (i.e. ''bi-directional'' neighborships are
established).
9 Test Cases
There are 16 test cases defined in this section. All test cases
except for 9.3, 9.4 and 9.10 can be used for any MVPN architecture
from [L3VPN-MCAST]. However, as noted in section 2, architectures
other than ''ROSEN-8'' might require additional test cases that are
beyond scope of this document. As [L3VPN-MCAST] specifies use of S-
PMSIs as optional, test cases 9.7-9.9 can be omitted for implementers
that don't support S-PMSIs. For such implementers test cases 9.12-17
SHOULD still be executed but without use of S-PMSIs and the exception
MUST be documented in the test report.
In Test Setup portion of each test case section ''P-instance Multicast
Configuration'' is not applicable to all MVPN architectures from
[L3VPN-MCAST] but only to those using PIM protocol to create
'tunnels' that instantiate MI-PMSI (such as ''ROSEN-8'' architecture).
All other portions of Test Setup are applicable to all MVPN
architectures.
Note that following relationships exist between ''Multicast Control
Plane Profile'' variables in ''Test Setup'' of each test case in section
9 and metric defined in section 5:
a. Number of MVPNs configured on DUT = Num_mVPN
b. Number of PIM VPN C-interfaces = Num_MC_C_ints/Num_mVPN
c. Number of remote PEs = Num_PIM_MI_PMSI_neigh/Num_mVPN
Dry, et al. Expires February 16, 2008 [Page 17]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
d. Num_*G_C = Num_mVPN *((Number of C-instance multicast groups in
encap direction) + (Number of C-instance multicast groups in
decap direction))
e. Num_SG_C = Num_mVPN * ((Number of C-instance sources per group
in encap direction)*(Number of C-instance multicast groups in
encap direction) + (Number of C-instance sources per group in
decap direction)*( Number of C-instance multicast groups in
decap direction))
f. Num_OIF_C = Num_mVPN*((Number of C-instance OIFs per (S,G) in
encap direction* Number of C-instance multicast groups in encap
direction *(1+ Number of C-instance sources per group in encap
direction)+ Number of C-instance OIFs per (S,G) in decap
direction* Number of C-instance multicast groups in decap
direction *(1+ Number of C-instance sources per group in decap
direction))
g. Number of data MDTs (S-PMSIs) sourced from DUT =
Num_SPMSI_Src/Num_mVPN
h. Number of data MDTs (S-PMSIs) with receivers behind DUT =
Num_SPMSI_Rx/Num_mVPN
i. Number of C-instance (S,G) flows using sourced data MDTs (S-
PMSIs) = Num_SPMSI_SrcFlows/Num_mVPN
j. Number of C-instance (S,G) flows using received data MDTs (S-
PMSIs) = Num_SPMSI_RxFlows/Num_mVPN
9.1''Empty'' MVPNs Scale
Test Objective:
To determine maximum number of MVPN instances that can be
configured and operational on the MVPN PE router. Note that we
refer here to mVPNs as ''empty'' as amount of PIM neighborships,
interfaces, C-instances multicast routes and SI-PMSIs associated
with given mVPN is negligible or zero in this test case.
Metric Variables Relationships:
Num_mVPN=Num_MC_C_ints=Num_PIM_C_neigh=Num_PIM_MI_PMSI_Neigh
Num_*G_C=Num_SG_C=2*Num_mVPN
Num_OIF_C=4*Num_mVPN
Dry, et al. Expires February 16, 2008 [Page 18]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT
groups: infinity
3. S-PMSI (Data MDT) Configuration:
a. S-PMSI used: NO
b. Protocol instantiating S-PMSIs: NA
4. C-instance Multicast Configuration:
a. Protocol for PIM C-instances: PIM-SM (ASM)
b. RP Location for PIM C-instances: Test apparatus port
closest to the source.
c. SPT threshold for PIM C-instances: zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs configured on DUT(Num_mVPN): varies
b. Number of PIM VPN C-interfaces: 1
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap direction:1
e. Number of C-instance sources per group in encap direction:1
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction:1
h. Number of C-instance sources per group in decap direction:1
i. Number of C-instance OIFs per (S,G) in decap direction:1
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 0
k. Number of data MDTs (S-PMSIs) sourced from DUT:0
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
Dry, et al. Expires February 16, 2008 [Page 19]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Execute number of test case instances where in each test case
instance number of configured mVPNs is varied with the goal of
finding maximum number of mVPNs that can be configured and
operational on DUT. Configured mVPN will be considered operational
if it satisfies all of following:
o Tunnel interface associated with this mVPN is operational
o Default MDT (MI-PMSI) associated with this mVPN is built
correctly according to core transport protocol rules (PIM for
''ROSEN-8'' architecture)
o On both DUT and Remote PE there is at least one PIM neighbor on
MI-PMSI. This condition is specific to MVPN architectures from
[L3VPN-MCAST] that use PIM as PE-PE signaling protocol, such as
''ROSEN-8''.
o There is at least one PIM neighbor on respective DUT's L3VPN C-
interface.
o All traffic flows are being received on ALL expected ports
without any drops.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of number of mVPNs achieved. It is DESIRABLE
to include the same data for at least 5 different values of number
of mVPNs (i.e. for at least 5 test case instances).
9.2 PIM Enabled VPN C-Interfaces Scale
Test Objective:
To determine maximum number of PIM enabled VPN C-interfaces that
can be operational on the MVPN PE router for couple of fixed values
of number of mVPNs. Amount of all other MVPN Metric such as PIM
neighborships and C-instances multicast routes is minimized in this
test case.
Metric Variables Relationships:
Num_MC_C_ints=Num_PIM_C_neigh >= Num_mVPN
Dry, et al. Expires February 16, 2008 [Page 20]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Num_PIM_MI_PMSI_Neigh=Num_mVPN
Num_*G_P=Num_mVPN
Num_*G_C=Num_SG_C=Num_OIF_C=0
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT threshold for Default MDT groups: infinity
3. S-PMSI (Data MDT) Configuration:
a. S-PMSIs used: NO
b. Protocol instantiating S-PMSIs : NA
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
c.SPT (Shortest Path Tree)threshold for PIM C-instances: zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs configured on DUT (Num_mVPN): varies
b. Number of PIM VPN C-interfaces: varies
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap
direction:0
e. Number of C-instance sources per group in encap
direction:0
f. Number of C-instance OIFs per (S,G) in encap direction:0
g. Number of C-instance multicast groups in decap
direction:0
h. Number of C-instance sources per group in decap
direction:0
i. Number of C-instance OIFs per (S,G) in decap direction:0
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 0
Dry, et al. Expires February 16, 2008 [Page 21]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
k. Number of data MDTs(S-PMSIs) sourced from DUT:0
l. Number of data MDTs(S-PMSIs) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
Following are steps to execute this test case:
1. Configure 100 mVPNs on DUT and PE2. Execute number of test case
instances where in each test case instance number of PIM enabled
VPN C-interfaces per mVPN is varied with the goal of finding
maximum number of PIM enabled VPN C-interfaces that can be
configured and operational on DUT. Configured VPN C-interface will
be considered operational if there is at least one bidirectional
PIM neighbor in VPN C-instance on configured C-interface.
2. Repeat step 1 for 100*I mVPNs where ''i=2
N'' where N is integer
value for which either maximum number of PIM enabled VPN C-
interfaces per mVPN becomes smaller than one or maximum number of
mVPNs found in test case 8.1 is reached.
Note that in this test case there SHOULD NOT be any multicast C-
instance traffic sources or receivers thus one MUST modify test
execution procedure from 7.1 and 7.2. For each test case instance
perform steps 1-3,7 from section 7.1. and 1-2,5-7 from section 7.2
for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum achieved value of number of PIM enabled VPN C-
interfaces. It is DESIRED to include the same data for at least 5
different values of PIM enabled VPN C-interfaces (i.e. for at least
5 test case instances).
9.3 PIM Neighborships Scale
Test Objective:
To determine maximum number of PIM C-instance neighborships across
MI-PMSIs that PE router can create and maintain. Amount of most of
other MVPN Metric such as C-instance multicast routes is minimized
in this test case.
Dry, et al. Expires February 16, 2008 [Page 22]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Metric Variables Relationships:
Num_PIM_MI_PMSI_Neigh > Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = Num_mVPN
Num_*G_C = Num_SG_C = 2*Num_mVPN
Num_OIF_C = 4*Num_mVPN
Num_*G_P = Num_SG_P = Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: NO
b.Protocol instantiating S-PMSIs: NA
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
c.SPT threshold for PIM C-instances: zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs configured on DUT (Num_mVPN): varies
b. Number of PIM VPN C-interfaces: 1
c. Number of remote PEs: varies
d. Number of C-instance multicast groups in encap direction:1
e. Number of C-instance sources per group in encap direction:1
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction:1
h. Number of C-instance sources per group in decap direction:1
i. Number of C-instance OIFs per (S,G) in decap direction:1
Dry, et al. Expires February 16, 2008 [Page 23]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 0
k. Number of data MDTs (S-PMSIs) sourced from DUT:0
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
Number of C-instance PIM neigborships across MI-PMSIs is
proportional to product of number of mVPNs DUT belongs to and
average number of PEs belonging to the same mVPNs. Depending on
implementation, it is possible that total number of PIM
nieghborships across MI-PMSIs that platform can scale to depends on
distribution of number of PE routers over mVPNs. For example, it is
possible that 100 mVPNs with average of 100 PEs per mVPN (which
results in 10,000 PIM neighbors) doesn't consume same DUT resources
as 50 mVPNs with average of 200 PEs per mVPN (which also results in
10,000 PIM neighbors). In order to identify whether this is the
case for given implementation, in this test case we will vary both
number of mVPNs per DUT (Num_mVPN) as well as average number of PE
routers per mVPN.
Test will consist of finding maximum number of C-instance PIM
neighborships across MDTs by varying average number of PEs per mVPN
for set of fixed values of number of mVPNs. Procedure is as
follows:
1. Configure 100 mVPNs on DUT. Execute number of test case
instances where in each test case instance number of PE routers
belonging to each mVPN is varied until maximum number of such
PE's is found. All mVPNs should have same number of PE routers.
2. Repeat step 1 for 100*I mVPNs where ''i=2
N'' where N is integer
value for which either maximum number of PEs per mVPN becomes
smaller than one or maximum number of mVPNs found in test case 9.1
is reached.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Dry, et al. Expires February 16, 2008 [Page 24]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of average number of PE's for every tested
value of number of mVPNs per PE (Num_mVPN). It is DESIRED to
include the same data for at least 5 different values of number of
PEs for each of tested values of number of mVPNs per PE(i.e. for at
least 5 test case instances per each tested value of number of
mVPNs).
9.4 Default MDT's (MI-PMSI's) PIM P-Instance Mroutes Scale
Test Objective:
To determine maximum number of mVPNs and PE routers per mVPN when
PIM P-instance is using protocol variant that generates maximum
amount of PIM P-instance mroutes. Amount of most of other MVPN
Metric such C-instance multicast mroutes is minimized in this test
case.
Metric Variables Relationships:
Num_SG_P >= 2*Num_mVPN
Num_*G_P = Num_mVPN
Num_PIM_MI_PMSI_Neigh > Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = Num_mVPN
Num_*G_C = Num_SG_C = 2*Num_mVPN
Num_OIF_C = 4*Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SSM
b. RP location for Default MDT groups: NA
Dry, et al. Expires February 16, 2008 [Page 25]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
NA
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: NO
b.Protocol instantiating S-PMSIs: NA
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
d. SPT (Shortest Path Tree)threshold for PIM C-instances: zero
5.Multicast Control Plane Profile (all per mVPN except a.; all from
DUT's perspective):
a. Number of MVPNs (Num_mVPN) configured on DUT: varies
b. Number of PIM VPN C-interfaces: 1
c. Number of remote PEs: varies
d. Number of C-instance multicast groups in encap direction:1
e. Number of C-instance sources per group in encap direction:1
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction:1
h. Number of C-instance sources per group in decap direction:1
i. Number of C-instance OIFs per (S,G) in decap direction:1
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 0
k. Number of data MDTs(S-PMSIs) sourced from DUT:0
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
Amount of PIM P-instance mroutes on PE router created by default
MDTs (MI-PMSIs) depends in general on choice of PIM protocol
variant, number of mVPNs and average number of PE routers per mVPN.
In order to assess the impact of PIM P-instance mroutes created by
MVPN default MDTs (MI-PMSIs) has on resources. Test case 9.4 will
be repeated with changing PIM P-instance protocol mode to SSM. Note
that test cases 9.1-9.3 use PIM-SM (ASM) with SPT threshold of
infinity in order to minimize impact PIM P-instance mroutes has on
Dry, et al. Expires February 16, 2008 [Page 26]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
resources while focusing on characterizing other variables
described in test cases 9.1-9.3
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of average number of PEs for every tested
value of number of mVPNs per PE. It is DESIRED to include the same
data for at least 5 different values of number of PEs for each of
tested values of number of mVPNs per PE(i.e. for at least 5 test
case instances per each tested value of number of mVPNs).
9.5 PIM C-instances Mroutes Scale
Test Objective:
To determine the maximum amount of PIM C-instance mroutes that a PE
router can create, maintain and forward on. Amount of most of other
MVPN Metric such as PIM neighborships and P-instance PIM mroutes is
minimized in this test case.
Metric Variables Relationships:
(Num_*G_C + Num_SG_C)>> Num_mVPN
Num_OIF_C >> Num_mVPN
Num_SG_P = 2*Num_mVPN
Num_*G_P = Num_mVPN
Num_PIM_MI_PMSI_Neigh = Num_MC_C_ints = Num_PIM_C_neigh = Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
Dry, et al. Expires February 16, 2008 [Page 27]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: NO
b.Protocol instantiating S-PMSIs: NA
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
c.SPT (Shortest Path Tree) threshold for PIM C-instances: zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs (Num_mVPN) configured on DUT: varies
b. Number of PIM VPN C-interfaces: 1
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap direction:
varies
e. Number of C-instance sources per group in encap
direction:50
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction:
varies
h. Number of C-instance sources per group in decap
direction:50
i. Number of C-instance OIFs per (S,G) in decap direction:1
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 0
k. Number of data MDTs (S-PMSIs) sourced from DUT:0
l. Number of data MDTs(S-PMSIs) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
Total number of C-instance PIM mroutes is proportional to product
of number of mVPNs DUT belongs to and average number of C-instance
PIM mroutes per mVPN. There are four distinct C-instance mroute
types that depending on implementation might be utilizing platform
resources in different way: (S,G) mroute with MDT Tunnel interface
in OIL (Outgoing Interface List); (*,G) mroute with MDT Tunnel
Dry, et al. Expires February 16, 2008 [Page 28]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
interface in OIL; (S,G) mroute with MDT Tunnel interface as IIF
(Incoming Interface) and (*,G) mroute with MDT Tunnel interface as
IIF. We will refer to mroute with MDT Tunnel in OIL as ''encap
mroute'' and to one with MDT Tunnel as IIF as ''decap mroute''.
In order to simplify testing we will assume a fixed number of S per
each G and thus will not exploit impact ratio of (S,G) to (*,G)
mroutes has on platform resources. However we will address couple
of scenarios with respect to ratio of encapsulation to
decapsulation C-instance mroutes.
Note that size of OIL can have significant impact on platform
resources and will be addressed in a separate test case: 9.6.
In addition depending on implementation it is possible that total
number of C-instance mroutes that platform can support depends on
distribution of mroutes over number of mVPNs. For example, it is
possible that 100 mVPNs with average of 100 C-instance mroutes per
mVPN (which results in total of 10,000 C-instance PIM mroutes )
doesn't consume same DUT resources as 50 mVPNs with average of 200
mroutes per mVPN (which also results in total of 10,000 C-instance
PIM mroutes ). In order to identify whether this is the case for
given implementation, in this test case we will vary both number of
mVPNs per DUT as well as average number of PIM C-instance mroutes
per mVPN.
Test will consist of finding maximum number of C-instance PIM
mroutes by varying average number of C-instance PIM mroutes per
mVPN for set of fixed values of number of mVPNs. Procedure is as
follows:
1. On DUT and PE2 configure 100 mVPNs. Setup environment such that
all PIM C-instance mroutes are in encap direction. Execute
number of test case instances using steps 1-7 in section 7.1
where in each test case instance number of C-instance PIM groups
is varied until maximum number of C-instance PIM mroutes is
found.
2. Repeat step 1 for 100*I mVPNs where ''i=2
N'' where N is integer
value for which either maximum number of C-instance PIM mroutes per
mVPN becomes smaller than one or maximum number of mVPNs found in
test case 9.1 is reached.
3. Repeat steps 1 and 2 for two more cases of ratios of encap:decap
C-instance mroutes: 100% mroutes are in decap direction;
10%encap+90%decap.
Dry, et al. Expires February 16, 2008 [Page 29]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of average number of PIM C-instance mroutes
for every tested value of number of mVPNs per PE. It is DESIRED to
include the same data for at least 5 different values of number of
PIM C-instance mroutes per mVPN for each of tested values of number
of mVPNs per PE(i.e. for at least 5 test case instances per each
tested value of number of mVPNs).
9.6 PIM C-Instances OIF Scale
Test Objective:
To determine the maximum amount of PIM C-instance OIFs that a PE
router can create and maintain. Amount of some of other MVPN Metric
such as PIM neighborships and P-instance PIM mroutes is minimized
in this test case.
Metric Variables Relationships:
Num_MC_C_ints = Num_PIM_C_neigh > Num_mVPN
(Num_*G_C + Num_SG_C)>> Num_mVPN
Num_OIF_C >> Num_mVPN
Num_SG_P = 2*Num_mVPN
Num_*G_P = Num_mVPN
Num_PIM_MI_PMSI_Neigh = Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2.P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
Dry, et al. Expires February 16, 2008 [Page 30]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
c.SPT (Shortest Path Tree)threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: NO
b.Protocol instantiating S-PMSIs: NA
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
a. SPT (Shortest Path Tree) threshold for PIM C-instances:
zero
5.Multicast Control Plane Profile (all per mVPN except a.; all from
DUT's perspective):
a. Number of MVPNs(Num_mVPN) configured on DUT: 100 and
maximum value tested in 9.5
b. Number of PIM VPN C-interfaces: maximum found in 9.2
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap direction:0
e. Number of C-instance sources per group in encap direction:0
f. Number of C-instance OIFs per (S,G) in encap direction:0
g. Number of C-instance multicast groups in decap direction:
varies
h. Number of C-instance sources per group in decap
direction:50
i. Number of C-instance OIFs per (S,G) in decap direction:
varies
j. Maximum allowed number of sourced data MDTs(S-PMSI)
configured on DUT: 0
k. Number of data MDTs(S-PMSI) sourced from DUT:0
l. Number of data MDTs(S-PMSI) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
Test will consist of finding the maximum number of C-instance PIM
OIFs by varying the average number OIFs per PIM C-instance mroute.
Maximum number will be found for couple of values of number of C-
instance PIM mroutes. Test will be executed for two values of
Dry, et al. Expires February 16, 2008 [Page 31]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
number of mVPNs: 100 and maximum value tested in 9.5.All C-instance
PIM mroutes will be in decap direction. Procedure is as follows:
1. For the first iteration of test number of C-instance decap
groups should be set to 25% of maximum value achieved in test
case instance of 9.5 where all C-instance groups were in decap
direction and 100 mVPNs was used. Execute number of test case
instances using steps 1-8 in section 7.1 where in each test case
instance average number of C-instance OIFs per mroute is varied
in increments of 2 until maximum number of OIFs is reached.
2. Repeat step 1 for 50%,75% and 100% of C-instance decap groups
achieved in test case 9.5.
3. Repeat steps 1 and 2 for the case of maximum number of mVPNs
tested in 9.5.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of OIFs per C-instance mroute for every
tested value of number of decapsulation groups per PE. It is
DESIRED to include the same data for at least 5 different values of
number of OIFs for each of tested values of number of decap
groups(i.e. for at least 5 test case instances per each tested
value of number of decap groups).
9.7 Joined S-PMSI (Data MDT) Scale
Test Objective:
To determine the maximum number of data MDTs (S-PMSIs) that a PE
can join. In order to assess maximum number of data MDTs (S-PMSI)
joined, we minimize resources taken by C-instance mroutes by
requiring that no data MDT (S-PMSI) reuse is utilized in this test
case. Note that depending on specific deployment context data MDT
reuse might or might not be preferred.
Metric Variables Relationships:
Num_SPMSI_Rx = Num_SPMSI_RxFlows > Num_mVPN
Num_SPMSI_Src=Num_SPMSI_SrcFlows = 0
Dry, et al. Expires February 16, 2008 [Page 32]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Num_PIM_MI_PMSI_Neigh = Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh > Num_mVPN
(Num_*G_C + Num_SG_C)>> Num_mVPN
Num_OIF_C >> Num_mVPN
Num_SG_P > 2*Num_mVPN
Num_*G_P > Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
d. SPT (Shortest Path Tree) threshold for PIM C-instances:
zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs (Num_mVPN) configured on DUT: maximum
number of mVPNs obtained in test case 9.5 (refer to it as
Vmax)
b. Number of PIM VPN C-interfaces: max found in 9.2 for Vmax
mVPNs
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap direction:0
e. Number of C-instance sources per group in encap direction:0
f. Number of C-instance OIFs per (S,G) in encap direction:0
Dry, et al. Expires February 16, 2008 [Page 33]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
g. Number of C-instance multicast groups in decap direction:
:[Smax/4] where Smax is maximum number of C-instance groups
obtained in test case 9.5 for Vmax number of mVPNs and case
where 100% of mroutes are in decap direction.
h. Number of C-instance sources per group in decap direction:2
i. Number of C-instance OIFs per (S,G) in decap direction:1
j. Maximum allowed number of sourced data MDTs (S-PMSI)
configured on DUT: 0
k. Number of data MDTs (S-PMSI) sourced from DUT:0
l. Number of data MDTs (S-PMSI)with receivers behind DUT: see
test procedure
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):varies
Test Execution Procedure:
Test will consist of varying number of data MDTs (S-PMSIs) for
flows that have receivers behind DUT (refer to those data MDTs (S-
PMSI) as ''received data MDTs''). During all test case instances
total number of C-instance PIM mroutes MUST remain constant and
will be [Smax/4] rounded to the first lower integer. We will vary
total number of received data MDTs (S-PMSIs) by varying number of
mVPNs configured to use data MDTs (S-PMSIs) at the remote PE that
has sources behind it, while number of data MDTs (S-PMSIs) per
mVPNs will be same for all mVPNs that use them. If given mVPN is
using data MDTs (S-PMSIs) in particular test case instance number
of them should be Dvpn=[Smax/(4*Vmax)] rounded to first lower value
that can be represented as 2^I where I is an integer. Note that
number of data MDTs (S-PMSIs) configured and sourced by DUT MUST be
zero in this test case. Procedure is as follows:
1. Configure one mVPN on the remote PE and all flows so that this
mVPN has Dvpn data MDTs (S-PMSIs) utilized and all are sourced
at the remote PE and received at DUT. Execute steps 1-7 in
section 7.1
2. Repeat step 1 where number of mVPNs that utilize data MDTs (in
the exact same way as 1 mVPN described in step1) takes following
values 25%,50%,75%,and 100% of Vmax.
Dry, et al. Expires February 16, 2008 [Page 34]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
3. If platform limit is not reached during execution of step 2,
increase number of data MDTs (S-PMSIs) per mVPN and repeat steps
1 and 2.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
all test case instances executed.
9.8 Sourced S-PMSI (Data MDT) Scale
Test Objective:
To determine maximum number of data MDTs (S-PMSIs) that PE can
source. In order to assess maximum number of data MDTs (S-PMSIs)
sourced, we minimize resources taken by C-instance mroutes by
requiring that no data MDT (S-PMSIs) reuse is utilized in this test
case. Note that depending on specific deployment context data MDT
reuse might or might not be preferred.
Metric Variables Relationships:
Num_SPMSI_Src = Num_SPMSI_SrcFlows > Num_mVPN
Num_SPMSI_Rx = Num_SPMSI_RxFlows = 0
Num_PIM_MI_PMSI_Neigh = Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = Num_mVPN
(Num_*G_C + Num_SG_C)>> Num_mVPN
Num_OIF_C >> Num_mVPN
Num_SG_P > 2*Num_mVPN
Num_*G_P > Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
Dry, et al. Expires February 16, 2008 [Page 35]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree)threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4. C- instance Multicast Configuration:
a. Protocol for PIM C-instances: PIM-SM (ASM)
b. RP Location for PIM C-instances: Test apparatus port
closest to the source.
c. SPT ((Shortest Path Tree) threshold for PIM C-instances:
zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs configured on DUT (Num_mVPN): maximum
number of mVPNs obtained in test case 9.5 (refer to it as
Vmax)
b. Number of PIM VPN C-interfaces: max found in 9.2 for Vmax
mVPNs
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap direction:
[Smax/4] where Smax is maximum number of C-instance groups
obtained in test case 9.5 for Vmax number of mVPNs and case
where 100% of mroutes are in encap direction.
e. Number of C-instance sources per group in encap direction:2
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction:0
h. Number of C-instance sources per group in decap direction:0
i. Number of C-instance OIFs per (S,G) in decap direction:0
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: see test case procedure
k. Number of data MDTs (S-PMSIs) sourced from DUT: see test
case procedure
l. Number of data MDTs (S-PMSIs) with receivers behind DUT: 0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSI):varies
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSI):0
Dry, et al. Expires February 16, 2008 [Page 36]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Test Execution Procedure:
Reverse role of DUT and remote PE from test case 9.7, where now DUT
is sourcing all data MDTs (S-PMSIs) while remote PE is on the
receiving end of them. Repeat test case 9.7 for this reversed role
scenario.
9.9 Data MDT (S-PMSI) Reuse
Test Objective:
To determine maximum number of C-instance flows that can utilize
data MDTs (S-PMSIs) and assess impact data MDT reuse has. Note that
depending on specific deployment context data MDT reuse might or
might not be preferred.
Metric Variables Relationships:
Num_SPMSI_RxFlows >= Num_SPMSI_Rx >= Num_mVPN
Num_SPMSI_SrcFlows >= Num_SPMSI_Src >= Num_mVPN
Num_PIM_MI_PMSI_Neigh = Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh > Num_mVPN
(Num_*G_C + Num_SG_C)>> Num_mVPN
Num_OIF_C >> Num_mVPN
Num_SG_P > 2*Num_mVPN
Num_*G_P > Num_mVPN
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
Dry, et al. Expires February 16, 2008 [Page 37]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4. C- instance Multicast Configuration:
a. Protocol for PIM C-instances: PIM-SM (ASM)
b. RP Location for PIM C-instances: Test apparatus port
closest to the source.
c. SPT (Shortest Path Tree) threshold for PIM C-instances:
zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs configured on DUT (Num_mVPN): maximum
number of mVPNs obtained in test case 9.5 (refer to it as
Vmax)
b. Number of PIM VPN C-interfaces: max found in 9.2 for Vmax
mVPNs
c. Number of remote PEs: 1
d. Number of C-instance multicast groups in encap direction: :
50% of Semax where Semax is maximum number of C-instance
encap groups obtained in test case 9.5 for Vmax number of
mVPNs and case where 10% of mroutes are in encap
direction.
e. Number of C-instance sources per group in encap
direction:50
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction: :
50% of Sdmax where Sdmax is maximum number of C-instance
encap groups obtained in test case 9.5 for Vmax number of
mVPNs and case where 90% of mroutes are in decap
direction..
h. Number of C-instance sources per group in decap
direction:50
i. Number of C-instance OIFs per (S,G) in decap direction:1
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 2
k. Number of data MDTs (S-PMSIs) sourced from DUT: 2
l. Number of data MDTs (S-PMSIs) with receivers behind DUT: 8
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):varies
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):varies
Dry, et al. Expires February 16, 2008 [Page 38]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Test Execution Procedure:
Test will consist of varying number of C-instance flows that will
utilize data MDT (S-PMSIs), while keeping number of C-instance
mroutes and data MDTs (S-PMSIs) constant. By doing this one can
assess impact of data MDT reuse.
Procedure is as follows:
1. Configure test apparatus such that number of flows using data
MDTs (S-PMSIs) is the same as number of data MDTs (S-PMSIs),
i.e. there is no data MDT reuse by multiple traffic flows.
Execute steps 1-7 in section 7.1 and 1-8 in section 7.2
2. Repeat step 1 for 10*I flows where ''i=2
N'' where N is integer
value for which either maximum number of flows mapped to data
MDT (S-PMSI) is reached or number of flows becomes equal to
number of (S,G) C-instance mroutes.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
all test case instances executed.
9.10 PIM C-instances J/P Suppression Effectiveness
Test Objective:
MI-PMSI functions as a broadcast network and standard PIM LAN (Local
Area Network) procedures, including PIM J/P Suppression, can be used.
Depending on distribution of C-instance sources, RPs and receivers in
MVPN network capability to perform J/P Suppression can have great
impact on overall scale capabilities of PE devices. In particular
largest impact is on scale capabilities of PE router whose attached
customers source large number of multicast flows or host large number
of RPs (refer to such PE as ''source'' PE)in the network with large
number of PE routers with receivers for those flows. However function
of PIM J/P Suppression is performed by all PE devices that have
receivers behind them (refer to such PE as ''receiving'' PE). Goal of
this test case is to assess capability of ''receiving'' PE to perform
J/P suppression for large amount of C-instance multicast routes.
Dry, et al. Expires February 16, 2008 [Page 39]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Metric Variables Relationships:
Num_PIM_MI_PMSI_Neigh = 2*Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = Num_mVPN
(Num_*G_C + Num_SG_C)>> Num_mVPN
Num_OIF_C >> Num_mVPN
Num_SG_P = 2*Num_mVPN
Num_*G_P = Num_mVPN
Num_SPMSI_Rx = Num_SPMSI_Src = 0
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology:
________ _________ ________
/ \ / \ / \
| |R1 | (DUT) |D2 | (RR) |
| Rx1 |====| PE1 |====| P |
| | D1| | B1| |
\________/ \_________/ \________/
||
|| ____________ _______
|| / \ / \
|| | (Emulated) |B3 | |
++===========| PE2 |====| Src |
|| B2| | B4| |
|| \____________/ \_______/
||
|| ____________ _______
|| / \ / \
|| | (Emulated) |B6 | |
++===========| PE3 |====| Rx2 |
B5| | B7| |
\____________/ \_______/
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
Dry, et al. Expires February 16, 2008 [Page 40]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: NO
b.Protocol instantiating S-PMSIs: NA
4. C- instance Multicast Configuration:
a. Protocol for PIM C-instances: PIM-SM (ASM)
b. RP Location for PIM C-instances: Test apparatus port
closest to the source.
c. SPT (Shortest Path Tree) threshold for PIM C-instances:
zero
5.Multicast Control Plane Profile (all per mVPN except a.; all from
DUT's perspective):
a. Number of MVPNs (Num_mVPN) configured on DUT (Num_mVPN):
varies
b. Number of PIM VPN C-interfaces: 1
c. Number of remote PEs: 2
d. Number of C-instance multicast groups in encap direction:
varies
e. Number of C-instance sources per group in encap
direction:50
f. Number of C-instance OIFs per (S,G) in encap direction:1
g. Number of C-instance multicast groups in decap direction:0
h. Number of C-instance sources per group in decap direction:0
i. Number of C-instance OIFs per (S,G) in decap direction:0
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 0
k. Number of data MDTs (S-PMSIs) sourced from DUT:0
l. Number of data MDTs(S-PMSIs) with receivers behind DUT:0
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):0
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):0
Test Execution Procedure:
For maximum number of C-instances multicast routes obtained in test
case 9.5 for 100 mVPNs and 100% mroutes in decap direction perform
following:
Dry, et al. Expires February 16, 2008 [Page 41]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
1) Establish all PIM session required to emulate defined
topology
2) Perform all C-instance PIM joins from ''Rx2'' (test
apparatus port B5 in topology diagram)
3) Start all traffic from ''Src'' (test apparatus port R1 in
topology diagram) and wait until steady state is
achieved.
4) On C-instance PIM session (established over MI-PMSI) of
test apparatus port ''Src'' (B2) measure number of J/P PDUs
received in 10 minute (J1) interval and calculate rate of
J/P PDUs as JR1=J1/(60*10)
5) Perform all C-instance PIM joins from test apparatus port
''Rx1'' (R1) and wait until steady state is achieved on
DUT.
6) On C-instance PIM session (established over MI-PMSI) of
test apparatus port ''Src'' (B2) measure number of J/P PDUs
received in 10 minute (J2) interval and calculate rate of
J/P PDUs as JR2=J2/(60*10)
7) If JR2 < 1.2*JR1 we can conclude that DUT is suppressing
J/P messages successfully.
Repeat steps 1-7, for maximum number of C-instances multicast routes
obtained in test case 9.5 for maximum number of mVPN and 100% state
in decap direction.
Note that no failure recovery testing is required in this test case.
Test Result Report:
Data listed in 8.1 MUST be reported in tabular format for all test
case instances. In addition rates JR1 and JR2 MUST be reported.
Optionally one can report absolute numbers or rates of number of
PIM J/P PDUs transmitted by DUT and PE3 (test apparatus port B5).
9.11 Additional Tests and Considerations for Devices Lacking ''Efficient''
Join/Prune Suppression
If 9.10 revealed that device does not perform J/P suppression, repeat
test case 9.5 where for all groups in encapsulation direction, J/P
Dry, et al. Expires February 16, 2008 [Page 42]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
messages are sent from more than one remote PE router, i.e. number of
remote PE routers with receivers becomes additional variable. One
MUST execute test for at least 3 values of number of remote PE
routers with receivers. It is suggested to chose values such that
product of number of PE routers with receivers and number of mVPNs is
50% of maximum number of PIM neighbors over MI-PMSIs achieved in test
9.3.
In addition, in test cases 9.12-9.17, test apparatus MUST be
configured such that all remote PEs are sending J/P message for any
given C-instance encapsulation group. On contrary if 9.10 revealed
that DUT platform efficiently performs J/P suppression, test
apparatus MUST be configured such that only one remote PE is sending
J/P message for any given C-instance encapsulation group.
Note that PIM Join/Prune suppression is relevant only for MVPN
architectures from [L3VPN-MCAST] that utilize PIM as PE-to-PE
signaling such as ''ROSEN-8'' architecture. However, even if other
PE-to-PE signaling methods are to be used for exchanging C-instance
PIM messages, the testing of C-instance PIM Join/Prune message rate
is still relevant. For example, if BGP is used as PE-PE signaling
distributing C-instance multicast routes , the rate of PIM messages
and its impact on PE depends on whether Route reflector to PE mroute
filtering is implemented. In addition, when BGP is used as PE-PE
signaling mechanism, the impact on Route Reflectors has to be also
measured but is beyond scope of this document.
9.12 Scale of mVPNs spanning large number of PEs
Test Objective:
As we noted mVPN scale is multidimensional and depends on number of
variables. While test cases 9.1-9.11 focused on only one or two
variables at the time while minimizing impact of all others, they
don't give good representation of platform capabilities in more
realistic deployment scenarios where none of variables are
minimized. Objective of this test case is to assess capabilities of
platform in more realistic deployment scenario. In particular this
test case will focus on finding maximum number of mVPN instances
that span large number of PE routers while they have values for
other MVPN variables chosen to be on the order of magnitude used by
MVPN deployments at the time this draft was written. Specific
values are defined in Test Setup section.
Dry, et al. Expires February 16, 2008 [Page 43]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Metric Variables Relationships:
Num_PIM_MI_PMSI_Neigh = 500*Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = 2*Num_mVPN
(Num_*G_C + Num_SG_C)= 30 * Num_mVPN
Num_OIF_C = Num_mVPN = 60 * Num_mVPN
Num_SPMSI_Rx = 8*Num_mVPN
Num_SPMSI_Src = 2*Num_mVPN
Num_SPMSI_RxFlows = 18*Num_mVPN
Num_SPMSI_SrcFlows = 2*Num_mVPN
Num_SG_P, Num_*G_P - depends on PIM protocol variant used for
MI-PMSIs
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: varies
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
c.SPT (Shortest Path Tree) threshold for PIM C-instances: zero
5.Multicast Control Plane Profile (all per mVPN except a.; all from
DUT's perspective):
a. Number of MVPNs configured on DUT: varies
b. Number of PIM VPN C-interfaces: 2
Dry, et al. Expires February 16, 2008 [Page 44]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
c. Number of remote PEs: 500
d. Number of C-instance multicast groups in encap direction: 1
e. Number of C-instance sources per group in encap direction:2
f. Number of C-instance OIFs per (S,G) in encap direction:2
g. Number of C-instance multicast groups in decap direction:9
h. Number of C-instance sources per group in decap direction:2
i. Number of C-instance OIFs per (S,G) in decap direction:2
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 2
k. Number of data MDTs (S-PMSIs) sourced from DUT:2
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:8
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):2
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):18
Test Execution Procedure:
This test case SHOULD be repeated for all PIM protocol variants(PIM
ASM, SSM and Bi-dir) supported by implementer for MI-PMSI (default
MDT). At minimum PIM ASM MUST be tested.
Refer to 9.11 for guidelines on how many PE routers should be
sending J/P messages for any given C-instance mroute in encap
direction.
Execute number of test case instances where in each test case
instance number of configured mVPNs is varied with the goal of
finding maximum number of mVPNs that platform can support. mVPN
instance here includes C-instance state, OIFs, PIM neighborships
and data MDTs (S-PMSIs) as specified by Test Setup.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of number of mVPNs achieved. It is DESIRED
to include the same data for at least 5 different values of number
of mVPNs (i.e. for at least 5 test case instances).
Dry, et al. Expires February 16, 2008 [Page 45]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
9.13 Scale of mVPNs with larger amount of state
Test Objective:
As we noted mVPN scale is multidimensional and depends on number of
variables. While test cases 9.1-9.11 focused on only one or two
variables at the time while minimizing impact of all others, they
don't give good representation of platform capabilities in more
realistic deployment scenarios where none of variables are
minimized. Objective of this test case just is to assess
capabilities of platform in more realistic deployment scenario. In
particular this test case will focus on finding maximum number of
mVPN instances that contain large number of C-instance PIM state
while they have values for other MVPN variables chosen to be on the
order of magnitude used by MVPN deployments at the time this draft
was written. Specific values are defined in Test Setup section.
Metric Variables Relationships:
Num_PIM_MI_PMSI_Neigh = 50*Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = 2*Num_mVPN
(Num_*G_C + Num_SG_C)= 300 * Num_mVPN
Num_OIF_C = Num_mVPN = 600 * Num_mVPN
Num_SPMSI_Rx = 8*Num_mVPN
Num_SPMSI_Src = 2*Num_mVPN
Num_SPMSI_RxFlows = 225*Num_mVPN
Num_SPMSI_SrcFlows = 25*Num_mVPN
Num_SG_P, Num_*G_P - depends on PIM protocol variant used for
MI-PMSIs
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: varies
Dry, et al. Expires February 16, 2008 [Page 46]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4. C- instance Multicast Configuration:
a.Protocol for PIM C-instances: PIM-SM (ASM)
b.RP Location for PIM C-instances: Test apparatus port closest
to the source.
c.SPT (Shortest Path Tree)threshold for PIM C-instances: zero
5.Multicast Control Plane Profile (all per mVPN except a.; all from
DUT's perspective):
a. Number of MVPNs configured on DUT (Num_mVPN) : varies
b. Number of PIM VPN C-interfaces: 2
c. Number of remote PEs: 50
d. Number of C-instance multicast groups in encap direction:5
e. Number of C-instance sources per group in encap direction:5
f. Number of C-instance OIFs per (S,G) in encap direction:2
g. Number of C-instance multicast groups in decap direction:45
h. Number of C-instance sources per group in decap direction:5
i. Number of C-instance OIFs per (S,G) in decap direction:2
j. Maximum allowed number of sourced data MDTs (S-
PMSIs)configured on DUT: 2
k. Number of data MDTs (S-PMSIs) sourced from DUT:2
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:8
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):25
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):225
Test Execution Procedure:
This test case SHOULD be repeated for all PIM protocol variants(PIM
ASM, SSM and Bi-dir) supported by implementer for MI-PMSI (default
MDT). At minimum PIM ASM MUST be tested.
Refer to 9.11 for guidelines on how many PE routers should be
sending J/P messages for any given C-instance mroute in encap
direction.
Dry, et al. Expires February 16, 2008 [Page 47]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Execute number of test case instances where in each test case
instance number of configured mVPNs is varied with the goal of
finding maximum number of mVPNs that platform can support. mVPN
instance here includes C-instance state, OIFs, PIM neighborships
and data MDTs (S-PMSIs) as specified by Test Setup.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of number of mVPNs achieved. It is DESIRED
to include the same data for at least 5 different values of number
of mVPNs (i.e. for at least 5 test case instances).
9.14 Scale of ''average'' size mVPNs
Test Objective:
As we noted mVPN scale is multidimensional and depends on number of
variables. While test cases 9.1-9.11 focused on only one or two
variables at the time while minimizing impact of all others, they
don't give good representation of platform capabilities in more
realistic deployment scenarios where none of variables are
minimized. While test cases 9.12 and 9.13 assess two more extreme
cases with respect to number of PE routers and mVPN routes,
objective of this test case is to assess number of mVPNs for the
case where each mVPN represents average size mVPN customer.
Specific values are defined in Test Setup section.
Metric Variables Relationships:
Num_PIM_MI_PMSI_Neigh = 100*Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = 2*Num_mVPN
(Num_*G_C + Num_SG_C)= 100 * Num_mVPN
Num_OIF_C = Num_mVPN = 200 * Num_mVPN
Num_SPMSI_Rx = 8*Num_mVPN
Num_SPMSI_Src = 2*Num_mVPN
Dry, et al. Expires February 16, 2008 [Page 48]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Num_SPMSI_RxFlows = 72*Num_mVPN
Num_SPMSI_SrcFlows = 8*Num_mVPN
Num_SG_P, Num_*G_P - depends on PIM protocol variant used for
MI-PMSIs
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1. Topology: Reference Topology #1
2. P-instance Multicast Configuration:
a. Protocol for Default MDT groups: varies
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree)threshold for Default MDT groups:
infinity
3. S-PMSI (Data MDT) Configuration:
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4. C- instance Multicast Configuration:
a. Protocol for PIM C-instances: PIM-SM (ASM)
b. RP Location for PIM C-instances: Test apparatus port
closest to the source.
c. SPT (Shortest Path Tree) threshold for PIM C-instances:
zero
5. Multicast Control Plane Profile (all per mVPN except a.; all
from DUT's perspective):
a. Number of MVPNs configured on DUT (Num_mVPN): varies
b. Number of PIM VPN C-interfaces: 2
c. Number of remote PEs: 100
d. Number of C-instance multicast groups in encap direction:2
e. Number of C-instance sources per group in encap direction:4
f. Number of C-instance OIFs per (S,G) in encap direction:2
g. Number of C-instance multicast groups in decap direction:18
h. Number of C-instance sources per group in decap direction:4
i. Number of C-instance OIFs per (S,G) in decap direction:2
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 2
k. Number of data MDTs (S-PMSIs) sourced from DUT:2
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:8
Dry, et al. Expires February 16, 2008 [Page 49]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):8
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):72
Test Execution Procedure:
This test case SHOULD be repeated for all PIM protocol variants(PIM
ASM, SSM and Bi-dir) supported by implementer for MI-PMSI (default
MDT). At minimum PIM ASM MUST be tested.
Execute number of test case instances where in each test case
instance number of configured mVPNs is varied with the goal of
finding maximum number of mVPNs that platform can support. mVPN
instance here includes C-instance state, OIFs, PIM neighborships
and data MDTs (S-PMSIs) as specified by Test Setup.
For each test case instance perform steps 1-8 from section 7.1. and
1-7 from section 7.2 for all mandatory stimuli in section 7.
Refer to 9.11 for guidelines on how many PE routers should be
sending J/P messages for any given C-instance mroute in encap
direction.
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of number of mVPNs achieved. It is DESIRED
to include the same data for at least 5 different values of number
of mVPNs (i.e. for at least 5 test case instances).
9.15 S-PMSI Switching Delay
Test Objective:
The test objective is to measure the elapsed time for traffic to
start flowing on S-PMSI, i.e., the time from the moment of signaling
of an S-PMSI to the moment when traffic starts flowing on the S-PMSI.
We will refer to this measure as S-PMSI switching delay [S-
PMSI_DELAY].
Metric Variables Relationships:
Same as for test case 9.14.
Dry, et al. Expires February 16, 2008 [Page 50]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Test Setup:
Same as for test case 9.14.
Test Execution Procedure:
Test will measure the time for traffic to start flowing on S-PMSI,
i.e., the time from the moment of signaling of an S-PMSI to the
moment when traffic starts flowing on the S-PMSI on the DUT. This
test MUST be repeated multiple (at least 20) times (for each value
of number of mVPNs) across multi-second intervals in order to
isolate any timing issues. This test MUST be performed with
varying number of average size MVPNs on DUT (up to the maximum) as
defined in the test case 9.14. With a given number of MVPNs on
DUT, the switching delay of several S-PMSIs sourced at the DUT in
different MVPNs will be measured. In case S-PSMI creation is
triggered by rate of C-instance traffic flow, the S-PMSI threshold
should be set to min possible value, depending on the
implementation. Such threshold value used MUST be documented in
the test report.
Refer to 9.11 for guidelines on how many PE routers should be
sending J/P messages for any given C-instance mroute in encap
direction.
Test Result Report:
The test results MUST include the range of S-PMSI switching
delays: minimum, average and maximum [S-PMSI_DELAY].
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of number of mVPNs achieved. It is DESIRED
to include the same data for at least 5 different values of number
of mVPNs (i.e. for at least 5 test case instances).
9.16 Convergence of C-Instance PIM Joins
Test Objective:
Dry, et al. Expires February 16, 2008 [Page 51]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
The test objective is to measure how long it takes for the first
receiver on the DUT, issuing C-instance PIM (*,G) Join, to receive
the traffic from already active C-instance source (S,G).
Metric Variables Relationships:
Same as for test case 9.14.
Test Setup:
Same as in test case 9.14
Test Execution Procedure:
Test will consist of an active C-instance source (S,G) attached
to/behind a remote PE (PE2 in Topology #1). There will be at least
one active C-instance receiver of (*,G) behind this remote PE
(PE2). This setup ensures that C-instance PIM Register procedure
for (S,G) has been completed and that there are no receivers
across the core network. With this initial setup, the test will
add one C-instance (*,G) receiver attached to DUT and issuing PIM
(*,G) Join towards the DUT. The test will measure the time
for traffic from (S,G) behind the remote PE to be received by
(*,G) receiver behind the DUT. This test MUST be repeated multiple
(at least 10) times in order to isolate any timing issues. This
test MUST be performed with varying number of average size MVPNs
(up to the maximum) as defined in the test case 9.14.
Refer to 9.11 for guidelines on how many PE routers should be
sending J/P messages for any given C-instance mroute in encap
direction.
Test Result Report:
The test results MUST include the range of C-instance PIM (*,G)
Join convergence times: minimum, average, maximum.
Data listed in 8.1 and 8.2 MUST be reported in tabular format for at
least maximum value of number of mVPNs achieved. It is DESIRED to
include the same data for at least 5 different values of number of
mVPNs (i.e. for at least 5 test case instances).
Dry, et al. Expires February 16, 2008 [Page 52]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
9.17 Effect of Co-locating C-RPs on a PE
Test Objective:
The test objective is to assess scaling impact of SP hosting
customer's RPs (C-RPs) on PE router. This is the optional
deployment model as stated in [MVPN-REQ] and is deployed today by
number of service providers. Only difference between test cases
9.14 and 9.17 is location of C-RP; thus by comparing test results
of 9.17 and 9.14 one will be able to determine additional impact
co-locating RP has on PE scale compared to deployment model of
customers hosting their own RPs.
Metric Variables Relationships:
Num_PIM_MI_PMSI_Neigh = 100*Num_mVPN
Num_MC_C_ints = Num_PIM_C_neigh = 2*Num_mVPN
(Num_*G_C + Num_SG_C)= 100 * Num_mVPN
Num_OIF_C = Num_mVPN = 200 * Num_mVPN
Num_SPMSI_Rx = 8*Num_mVPN
Num_SPMSI_Src = 2*Num_mVPN
Num_SPMSI_RxFlows = 72*Num_mVPN
Num_SPMSI_SrcFlows = 8*Num_mVPN
Num_SG_P, Num_*G_P -depends on PIM protocol variant used for
MI-PMSIs
Test Setup:
Following test setup MUST be performed prior to executing this test
case
1.Topology: Reference Topology #1
2.P-instance Multicast Configuration:
a. Protocol for Default MDT groups: PIM-SM (ASM)
b. RP location for Default MDT groups: P router
c. SPT (Shortest Path Tree) threshold for Default MDT
groups: infinity
3.S-PMSI (Data MDT) Configuration:
Dry, et al. Expires February 16, 2008 [Page 53]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
a.S-PMSI used: YES
b.Protocol instantiating S-PMSIs: PIM SSM
4.C-instance Multicast Configuration:
a. Protocol for PIM C-instances: PIM-SM (ASM)
b. RP Location for PIM C-instances: DUT
c. SPT threshold for PIM C-instances: zero
5.Multicast Control Plane Profile (all per mVPN except a.; all from
DUT's perspective):
a. Number of MVPNs configured on DUT: varies
b. Number of PIM VPN C-interfaces: 2
c. Number of remote PEs: 100
d. Number of C-instance multicast groups in encap direction:2
e. Number of C-instance sources per group in encap direction:4
f. Number of C-instance OIFs per (S,G) in encap direction:2
g. Number of C-instance multicast groups in decap direction:18
h. Number of C-instance sources per group in decap direction:4
i. Number of C-instance OIFs per (S,G) in decap direction:2
j. Maximum allowed number of sourced data MDTs (S-PMSIs)
configured on DUT: 2
k. Number of data MDTs (S-PMSIs) sourced from DUT:2
l. Number of data MDTs (S-PMSIs) with receivers behind DUT:8
m. Number of C-instance (S,G) flows using sourced data MDTs
(S-PMSIs):8
n. Number of C-instance (S,G) flows using received data MDTs
(S-PMSIs):72
Test Execution Procedure:
This test case SHOULD be repeated for all PIM protocol variants(PIM
ASM, SSM and Bi-dir) supported by implementer for MI-PMSI (default
MDT). At minimum PIM ASM MUST be tested.
Refer to 9.11 for guidelines on how many PE routers should be
sending J/P messages for any given C-instance mroute in encap
direction.
Execute number of test case instances where in each test case
instance number of configured mVPNs is varied with the goal of
finding maximum number of mVPNs that platform can support in this
environment. mVPN instance here includes C-instance state, OIFs,
PIM neighborships and data MDTs (S-PMSIs) as specified by Test
Setup.
Dry, et al. Expires February 16, 2008 [Page 54]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
For each test case instance perform following steps:
a. Steps 1-4 from section 7.1.
b. Send PIM Register messages from all ''source'' test apparatus
ports
c. Test apparatus should verify that correct (S,G) PIM Join
messages had been received by ''source'' test apparatus port.
In reaction to receipt of (S,G) joins, source test
apparatus ports should start transmitting multicast traffic
to appropriate multicast groups and start sending Data-
header Registers [RFC4601].
d. Steps 6-8 from section 7.1.
For all mandatory stimuli defined in section 7 perform following
steps:
a. Steps a-d from paragraph above
b. Steps 2-7 from section 7.2
Test Result Report:
Data listed in 8.1 and 8.2 MUST be reported in tabular format for
at least maximum value of number of mVPNs achieved. It is DESIRED
to include the same data for at least 5 different values of number
of mVPNs (i.e. for at least 5 test case instances).
10 Security Considerations
Documents of this type do not directly affect the security of
the Internet or of corporate networks as long as benchmarking
is not performed on devices or systems connected to operating
networks.
11 IANA Considerations
This document requires no IANA considerations.
12 Acknowledgments
We would like to thank Aamer Akhter, Arjen Boers, Yiqun Cai, Min Li,
Amal Maalouf, Mike McBride, Ciprian Popoviciu, Dan Williston, Rajiv
Dry, et al. Expires February 16, 2008 [Page 55]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Asati and Thomas Morin for their valuable feedback on content of this
draft. We would like to thank Nick Satsia for his support with test
verification of this draft.
13 References
13.1 Normative References
[MVPN-REQ] T. Morin, Ed., ''Requirements for Multicast in L3 Provider-
Provisioned VPNs'', draft-ietf-l3vpn-ppvpn-mcast-reqts-09.txt
[L3VPN-MCAST] E. Rosen, R. Aggarwal, ''Multicast in MPLS/BGP IP VPNs'',
draft-ietf-l3vpn-2547bis-mcast-03.txt
[RFC4364] E.Rosen, Y. Rekhter, ''BGP/MPLS IP Virtual Private Networks
(VPNs)''
[RFC4601] B. Fenner, M. Handley, H. Holbrook, I. Kouvelas, ''Protocol
Independent Multicast - Sparse Mode (PIM-SM):Protocol Specification''
13.2 Informative References
[ROSEN-8] E. Rosen, Y. Cai, I. Wijnands, "Multicast in MPLS/BGP IP
VPNs", draft-rosen-vpn-mcast-08.txt
[MVPN-BCP] Y. Cai, M. McBride, C. Hall, M. Napierala, ''Multicast VPN
Deployment Recommendations'', draft-ycai-mboned-mvpn-deploy-00.txt
Dry, et al. Expires February 16, 2008 [Page 56]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Author's Addresses
Silvija A. Dry
Cisco
7025 Kit Creek Rd.
Research Triangle Park, NC 27709
sdry@cisco.com
Fernando Calabria
Cisco
7025 Kit Creek Rd.
Research Triangle Park, NC 27709
fcalabri@cisco.com
Maria Napierala
AT&T
200 Laurel Avenue
Middletown, NJ 07748
mnapierala@att.com
Yuji Kamite
NTT Corporation
Tokyo Opera City Tower
3-20-2 Nishi Shinjuku, Shinjuku-ku
Tokyo 163-1421
Japan
y.kamite@ntt.com
Ian Yee Yan Fung
Cisco Systems, Inc.
ifung@cisco.com
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
Dry, et al. Expires February 16, 2008 [Page 57]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on
an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
IETF TRUST, AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE
ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Dry, et al. Expires February 16, 2008 [Page 58]
Internet-Draft Multicast VPN Scalability Benchmarking August 2007
Dry, et al. Expires February 16, 2008 [Page 59]