IPPM H. Song
Internet-Draft Futurewei Technologies
Intended status: Informational G. Mirsky
Expires: January 10, 2022 ZTE Corp.
C. Filsfils
A. Abdelsalam
Cisco Systems, Inc.
T. Zhou
Z. Li
Huawei
J. Shin
SK Telecom
K. Lee
LG U+
July 9, 2021
Postcard-based On-Path Flow Data Telemetry using Packet Marking
draft-song-ippm-postcard-based-telemetry-10
Abstract
The document describes a packet-marking variation of the Postcard-
Based Telemetry (PBT), referred to as PBT-M. Similar to the
instruction-based PBT (i.e., IOAM DEX), PBT-M does not carry the
telemetry data in user packets but send the telemetry data through a
dedicated packet. Unlike the instruction-based PBT, PBT-M does not
require an extra instruction header. PBT-M raises some unique issues
that need to be considered. This document formally describes the
high level scheme and cover the common requirements and issues when
applying PBT-M in different networks. PBT-M is complementary to the
other on-path telemetry schemes such as IOAM.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
Song, et al. Expires January 10, 2022 [Page 1]
Internet-Draft PBT using Packet Marking July 2021
This Internet-Draft will expire on January 10, 2022.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Motivation . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. PBT-M: Marking-based PBT . . . . . . . . . . . . . . . . . . 3
3. New Challenges . . . . . . . . . . . . . . . . . . . . . . . 5
4. PBT-M Design Considerations . . . . . . . . . . . . . . . . . 6
4.1. Packet Marking . . . . . . . . . . . . . . . . . . . . . 6
4.2. Flow Path Discovery . . . . . . . . . . . . . . . . . . . 6
4.3. Packet Identity for Export Data Correlation . . . . . . . 7
4.4. Control the Load . . . . . . . . . . . . . . . . . . . . 7
5. Implementation Recommendation . . . . . . . . . . . . . . . . 8
5.1. Configuration . . . . . . . . . . . . . . . . . . . . . . 8
5.2. Postcard Format . . . . . . . . . . . . . . . . . . . . . 8
5.3. Data Correlation . . . . . . . . . . . . . . . . . . . . 8
6. Security Considerations . . . . . . . . . . . . . . . . . . . 9
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 9
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 9
10. Informative References . . . . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10
1. Motivation
To gain detailed data plane visibility to support effective network
OAM, it is essential to be able to examine the trace of user packets
along their forwarding paths. Such on-path flow data reflect the
state and status of each user packet's real-time experience and
provide valuable information for network monitoring, measurement, and
diagnosis.
Song, et al. Expires January 10, 2022 [Page 2]
Internet-Draft PBT using Packet Marking July 2021
The telemetry data include but not limited to the detailed forwarding
path, the timestamp/latency at each network node, and, in case of
packet drop, the drop location, and the reason. The emerging
programmable data plane devices allow user-defined data collection or
conditional data collection based on trigger events. Such on-path
flow data are from and about the live user traffic, which complements
the data acquired through other passive and active OAM mechanisms
such as IPFIX [RFC7011] and ICMP [RFC2925].
On-path telemetry was developed to cater to the need of collecting
on-path flow data. There are two basic modes for on-path telemetry:
the passport mode and the postcard mode. In the passport mode, each
node on the path adds the telemetry data to the user packets (i.e.,
stamp the passport). The accumulated data-trace carried by user
packets are exported at a configured end node. In the postcard mode,
each node directly exports the telemetry data using an independent
packet (i.e., send a postcard) to avoid the need for carrying the
data with user packets.
The postcard mode is complementary to the passport mode. In the
variant of the postcard-based telemetry (PBT) which uses an
instruction header, the postcards that carry telemetry data can be
generated by a node's slow path and transported in-band or out-of-
band, independent of the original user packets. IOAM direct export
option (DEX) [I-D.ietf-ippm-ioam-direct-export] is a representative
of instruction-based PBT.
This document describes another variation of the postcard mode on-
path telemetry, the marking-based PBT (PBT-M). Unlike the
instruction-based PBT, PBT-M does not require a telemetry instruction
header. However, PBT-M has unique issues that need to be considered.
This document discusses the challenges and their solutions which are
common to the high-level scheme of PBT-M.
2. PBT-M: Marking-based PBT
As the name suggests, PBT-M only needs a marking-bit in the existing
headers of user packets to trigger the telemetry data collection and
export. The sketch of PBT-M is as follows. If on-path data need to
be collected, the user packet is marked at the path head node. At
each PBT-aware node, if the mark is detected, a postcard (i.e., the
dedicated OAM packet triggered by a marked user packet) is generated
and sent to a collector. The postcard contains the data requested by
the management plane. The requested data are configured by the
management plane. Once the collector receives all the postcards for
a single user packet, it can infer the packet's forwarding path and
analyze the data set. The path end node is configured to unmark the
packets to its original format if necessary.
Song, et al. Expires January 10, 2022 [Page 3]
Internet-Draft PBT using Packet Marking July 2021
The overall architecture of PBT-M is depicted in Figure 1.
+------------+ +-----------+
| Network | | Telemetry |
| Management |(-------| Data |
| | | Collector |
+-----:------+ +-----------+
: ^
:configurations |postcards
: |(OAM pkts)
...............:.....................|........
: : : | :
: +---------:---+-----------:---+--+-------:---+
: | : | : | : |
V | V | V | V |
+------+-+ +-----+--+ +------+-+ +------+-+
usr pkts | Head | | Path | | Path | | End |
====>| Node |====>| Node |====>| Node |====>| Node |===>
| | | A | | B | | |
+--------+ +--------+ +--------+ +--------+
mark usr pkts gen postcards gen postcards gen postcards
gen postcards unmark usr pkts
Figure 1: Architecture of PBT-M
The advantages of PBT-M are summarized as follows.
o 1: PBT-M avoids augmenting user packets with new headers and the
signaling for telemetry data collection remains in the data plane.
o 2: PBT-M is extensible for collecting arbitrary new data to
support possible future use cases. The data set to be collected
can be configured through the management plane or control plane.
o 3: PBT-M can avoid interfering with the normal forwarding. The
collected data are free to be transported independently through
in-band or out-of-band channels. The data collecting, processing,
assembly, encapsulation, and transport are, therefore, decoupled
from the forwarding of the corresponding user packets and can be
performed in data-plane slow-path if necessary.
o 4: For PBT-M, the types of data collected from each node can vary
depending on application requirements and node capability.
o 5: PBT-M makes it easy to secure the collected data without
exposing it to unnecessary entities. For example, both the
Song, et al. Expires January 10, 2022 [Page 4]
Internet-Draft PBT using Packet Marking July 2021
configuration and the telemetry data can be encrypted and/or
authenticated before being transported, so passive eavesdropping
and a man-in-the-middle attack can both be deterred.
o 6: Even if a user packet under inspection is dropped at some node
in the network, the postcards collected from the preceding nodes
are still valid and can be used to diagnose the packet drop
location and reason.
3. New Challenges
Although PBT-M addresses the issues of the passport mode telemetry
and the instruction-based PBT, it introduces a few new challenges.
o Challenge 1 (Packet Marking): A user packet needs to be marked to
trigger the path-associated data collection. Since the PBT-M does
not augment user packets with any new header fields, it needs to
reserve or reuse bits from the existing header fields. This
raises a similar issue as in the Alternate Marking Scheme
[RFC8321]
o Challenge 2 (Configuration): Since the packet header will not
carry OAM instructions anymore, the data plane devices need to be
configured to know what data to collect. However, in general, the
forwarding path of a flow packet (due to ECMP or dynamic routing)
is unknown beforehand (note that there are some notable
exceptions, such as segment routing). If the per-flow customized
data collection is required, configuring the data set for each
flow at all data plane devices might be expensive in terms of
configuration load and data plane resources.
o Challenge 3 (Data Correlation): Due to the variable transport
latency, the dedicated postcard packets for a single packet may
arrive at the collector out of order or be dropped in networks for
some reason. In order to infer the packet forwarding path, the
collector needs some information from the postcard packets to
identify the user packet affiliation and the order of path node
traversal.
o Challenge 4 (Load Overhead): Since each postcard packet has its
header, the overall network bandwidth overhead of PBT can be high.
A large number of postcards could add processing pressure on data
collecting servers. That can be used as an attack vector for DoS.
Song, et al. Expires January 10, 2022 [Page 5]
Internet-Draft PBT using Packet Marking July 2021
4. PBT-M Design Considerations
To address the above challenges, we propose several design details of
PBT-M.
4.1. Packet Marking
To trigger the path-associated data collection, usually, a single bit
from some header field is sufficient. While no such bit is
available, other packet-marking techniques are needed. We discuss
several possible application scenarios.
o IPv4. Alternate Marking (AM) [RFC8321] is an IP flow performance
measurement framework that also requires a single bit for packet
coloring. The difference is that AM does in-network measurement
while PBT-M only collects and exports data at network nodes (i.e.,
the data analysis is done at the collector rather than in the
network nodes). AM suggests to use some reserved bit of the Flag
field or some unused bit of the TOS field. Actually, AM can be
considered a sub-case of PBT-M, so that the same bit can be used
for PBT-M. The management plane is responsible for configuring
the actual operation mode.
o SFC NSH. The OAM bit in the NSH header can be used to trigger the
on-path data collection [I-D.ietf-sfc-nsh]. PBT does not add any
other metadata to NSH.
o MPLS. Instead of choosing a header bit, we take advantage of the
synonymous flow label [I-D.bryant-mpls-synonymous-flow-labels]
approach to mark the packets. A synonymous flow label indicates
the on-path data should be collected and forwarded through a
postcard.
o SRv6: A flag bit in SRH can be reserved to trigger the on-path
data collection [I-D.song-6man-srv6-pbt]. SRv6 OAM
[I-D.ietf-6man-spring-srv6-oam] has adopted the O-bit in SRH flags
as the marking bit to trigger the telemetry.
4.2. Flow Path Discovery
In case the path that a flow traverses is unknown in advance, all
PBT-aware nodes should be configured to react to the marked packets
by exporting some basic data, such as node ID and TTL before a data
set template for that flow is configured. This way, the management
plane can learn the flow path dynamically.
If the management plane wants to collect the on-path data for some
flow, it configures the head node(s) with a probability or time
Song, et al. Expires January 10, 2022 [Page 6]
Internet-Draft PBT using Packet Marking July 2021
interval for the flow packet marking. When the first marked packet
is forwarded in the network, the PBT-aware nodes will export the
basic data set to the collector. Hence, the flow path is identified.
If other data types need to be collected, the management plane can
further configure the data set's template to the target nodes on the
flow's path. The PBT-aware nodes collect and export data accordingly
if the packet is marked and a data set template is present.
If the flow path is changed for any reason, the new path can be
quickly learned by the collector. Consequently, the management plane
controller can be directed to configure the nodes on the new path.
The outdated configuration can be automatically timed out or
explicitly revoked by the management plane controller.
4.3. Packet Identity for Export Data Correlation
The collector needs to correlate all the postcard packets for a
single user packet. Once this is done, the TTL (or the timestamp, if
the network time is synchronized) can be used to infer the flow
forwarding path. The key issue here is to correlate all the
postcards for the same user packet.
The first possible approach includes the flow ID plus the user packet
ID in the OAM packets. For example, the flow ID can be the 5-tuple
IP header of the user traffic, and the user packet ID can be some
unique information pertaining to a user packet (e.g., the sequence
number of a TCP packet).
If the packet marking interval is large enough, the flow ID is enough
to identify a user packet. As a result, it can be assumed that all
the exported postcard packets for the same flow during a short time
interval belong to the same user packet.
Alternatively, if the network is synchronized, then the flow ID plus
the timestamp at each node can also infer the postcard affiliation.
However, some errors may occur under some circumstances. For
example, two consecutive user packets from the same flows are marked,
but one exported postcard from a node is lost. It is difficult for
the collector to decide to which user packet the remaining postcard
is related. In many cases, such a rare error has no catastrophic
consequence. Therefore it is tolerable.
4.4. Control the Load
PBT-M should not be applied to all the packets all the time. It is
better to be used in an interactive environment where the network
telemetry applications dynamically decide which subset of traffic is
under scrutiny. The network devices can limit the PBT rate through
Song, et al. Expires January 10, 2022 [Page 7]
Internet-Draft PBT using Packet Marking July 2021
sampling and metering. The PBT packets can be distributed to
different servers to balance the processing load.
It is important to understand that the total amount of data exported
by PBT-M is identical to that of IOAM. The only extra overhead is
the packet header of the postcards. In the case of IOAM, it carries
the data from each node throughout the path to the end node before
exporting the aggregated data. On the other hand, PBT-M directly
exports local data. The overall network bandwidth impact depends on
the network topology and scale, and PBT-M could be more bandwidth
efficient.
5. Implementation Recommendation
5.1. Configuration
The head node's ACL should be configured to filter out the target
flows for telemetry data collection. Optionally, a flow packet
sampling rate or probability could be configured to monitor a subset
of the flow packets.
The telemetry data set that should be exported by postcards at each
path node could be configured using the data set templates specified,
for example, in IPFIX [RFC7011]. In future revisions, we will
provide more details.
The PBT-aware path nodes could be configured to respond or ignore the
marked packets.
5.2. Postcard Format
The postcard should use the same data export format as that used by
IOAM. [I-D.spiegel-ippm-ioam-rawexport] proposes a raw format that
can be interpreted by IPFIX. In future revisions, we will provide
more details.
5.3. Data Correlation
Enough information should be included to help the collector to
correlate and order the postcards for a single user packet.
Section 4.3 provides several possible means. The application
scenario and network protocol are important factors to determine the
means to use. In future revisions, we will provide details for
representative applications.
Song, et al. Expires January 10, 2022 [Page 8]
Internet-Draft PBT using Packet Marking July 2021
6. Security Considerations
Several security issues need to be considered.
o Eavesdrop and tamper: the postcards can be encrypted and
authenticated to avoid such security threats.
o DoS attack: PBT can be limited to a single administrative domain.
The mark must be removed at the egress domain edge. The node can
rate-limit the extra traffic incurred by postcards.
7. IANA Considerations
No requirement for IANA is identified.
8. Contributors
We thank Alfred Morton who provided valuable suggestions and comments
helping improve this draft.
9. Acknowledgments
TBD.
10. Informative References
[I-D.bryant-mpls-synonymous-flow-labels]
Bryant, S., Swallow, G., Sivabalan, S., Mirsky, G., Chen,
M., and Z. Li, "RFC6374 Synonymous Flow Labels", draft-
bryant-mpls-synonymous-flow-labels-01 (work in progress),
July 2015.
[I-D.ietf-6man-spring-srv6-oam]
Ali, Z., Filsfils, C., Matsushima, S., Voyer, D., and M.
Chen, "Operations, Administration, and Maintenance (OAM)
in Segment Routing Networks with IPv6 Data plane (SRv6)",
draft-ietf-6man-spring-srv6-oam-07 (work in progress),
July 2020.
[I-D.ietf-ippm-ioam-direct-export]
Song, H., Gafni, B., Zhou, T., Li, Z., Brockners, F.,
Bhandari, S., Sivakolundu, R., and T. Mizrahi, "In-situ
OAM Direct Exporting", draft-ietf-ippm-ioam-direct-
export-00 (work in progress), February 2020.
Song, et al. Expires January 10, 2022 [Page 9]
Internet-Draft PBT using Packet Marking July 2021
[I-D.ietf-sfc-nsh]
Quinn, P., Elzur, U., and C. Pignataro, "Network Service
Header (NSH)", draft-ietf-sfc-nsh-28 (work in progress),
November 2017.
[I-D.song-6man-srv6-pbt]
Song, H., "Support Postcard-Based Telemetry for SRv6 OAM",
draft-song-6man-srv6-pbt-01 (work in progress), October
2019.
[I-D.spiegel-ippm-ioam-rawexport]
Spiegel, M., Brockners, F., Bhandari, S., and R.
Sivakolundu, "In-situ OAM raw data export with IPFIX",
draft-spiegel-ippm-ioam-rawexport-01 (work in progress),
October 2018.
[RFC2925] White, K., "Definitions of Managed Objects for Remote
Ping, Traceroute, and Lookup Operations", RFC 2925,
DOI 10.17487/RFC2925, September 2000,
<https://www.rfc-editor.org/info/rfc2925>.
[RFC7011] Claise, B., Ed., Trammell, B., Ed., and P. Aitken,
"Specification of the IP Flow Information Export (IPFIX)
Protocol for the Exchange of Flow Information", STD 77,
RFC 7011, DOI 10.17487/RFC7011, September 2013,
<https://www.rfc-editor.org/info/rfc7011>.
[RFC8321] Fioccola, G., Ed., Capello, A., Cociglio, M., Castaldelli,
L., Chen, M., Zheng, L., Mirsky, G., and T. Mizrahi,
"Alternate-Marking Method for Passive and Hybrid
Performance Monitoring", RFC 8321, DOI 10.17487/RFC8321,
January 2018, <https://www.rfc-editor.org/info/rfc8321>.
Authors' Addresses
Haoyu Song
Futurewei Technologies
2330 Central Expressway
Santa Clara, 95050
USA
Email: hsong@futurewei.com
Greg Mirsky
ZTE Corp.
Email: gregimirsky@gmail.com
Song, et al. Expires January 10, 2022 [Page 10]
Internet-Draft PBT using Packet Marking July 2021
Clarence Filsfils
Cisco Systems, Inc.
Belgium
Email: cfilsfil@cisco.com
Ahmed Abdelsalam
Cisco Systems, Inc.
Italy
Email: ahabdels@cisco.com
Tianran Zhou
Huawei
156 Beiqing Road
Beijing, 100095
P.R. China
Email: zhoutianran@huawei.com
Zhenbin Li
Huawei
156 Beiqing Road
Beijing, 100095
P.R. China
Email: lizhenbin@huawei.com
Jongyoon Shin
SK Telecom
South Korea
Email: jongyoon.shin@sk.com
Kyungtae Lee
LG U+
South Korea
Email: coolee@lguplus.co.kr
Song, et al. Expires January 10, 2022 [Page 11]