MBONED Working Group Percy S. Tarapore
Internet Draft Robert Sayko
Intended status: BCP AT&T
Expires: August 3, 2014 Greg Shepherd
Toerless Eckert
Cisco
Ram Krishnan
Brocade
March 3, 2014
Multicasting Applications Across Inter-Domain Peering Points
draft-tarapore-mboned-multicast-cdni-05.txt
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 3, 2014.
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Tarapore, et al Expires August 3, 2014 [Page 1]
IETF I-D Multicasting Applications Across Peering Points February 2014
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Abstract
This document examines the process of transporting applications via
multicast across inter-domain peering points. The objective is to
describe the setup process for multicast-based delivery across
administrative domains and document supporting functionality to
enable this process.
Table of Contents
1. Introduction...................................................3
2. Overview of Inter-domain Multicast Application Transport.......3
3. Inter-domain Peering Point Requirements for Multicast..........5
3.1. Native Multicast..........................................5
3.2. Peering Point Enabled with GRE Tunnel.....................6
3.3. Peering Point Enabled with an AMT - Both Domains Multicast
Enabled........................................................8
3.4. Peering Point Enabled with an AMT - AD-2 Not Multicast
Enabled........................................................9
3.5. AD-2 Not Multicast Enabled - Multiple AMT Tunnels Through
AD-2..........................................................11
4. Supporting Functionality......................................13
4.1. Network Interconnection Transport and Security Guidelines14
4.2. Routing Aspects and Related Guidelines...................15
4.2.1 Native Multicast Routing Aspects..................15
4.2.2 GRE Tunnel over Interconnecting Peering Point.....16
4.2.3 Routing Aspects with AMT Tunnels.....................16
4.3. Back Office Functions - Billing and Logging Guidelines...19
4.4. Operations - Service Performance and Monitoring Guidelines19
4.5. Reliability Models/Service Assurance Guidelines..........19
4.6. Provisioning Guidelines..................................19
4.7. Client Models............................................19
4.8. Addressing Guidelines....................................19
5. Security Considerations.......................................19
Tarapore, et al Expires August 3, 2014 [Page 2]
IETF I-D Multicasting Applications Across Peering Points February 2014
6. IANA Considerations...........................................20
7. Conclusions...................................................20
8. References....................................................20
8.1. Normative References.....................................20
8.2. Informative References...................................20
9. Acknowledgments...............................................20
1. Introduction
Several types of applications (e.g., live video streaming, software
downloads) are well suited for delivery via multicast means. The use
of multicast for delivering such applications offers significant
savings for utilization of resources in any given administrative
domain. End user demand for such applications is growing. Often,
this requires transporting such applications across administrative
domains via inter-domain peering points.
The objective of this Best Current Practices document is twofold:
o Describe the process and establish guidelines for setting up
multicast-based delivery of applications across inter-domain
peering points, and
o Catalog all required information exchange between the
administrative domains to support multicast-based delivery.
While there are several multicast protocols available for use, this
BCP will focus the discussion to those that are applicable and
recommended for the peering requirements of today's service model,
including:
o Protocol Independent Multicast - Source Specific Multicast
(PIM-SSM) [RFC4607]
o Internet Group Management Protocol (IGMP) v3 [RFC4604]
o Multicast Listener Discovery (MLD) [RFC4604]
This document therefore serves the purpose of a "Gap Analysis"
exercise for this process. The rectification of any gaps identified
- whether they involve protocol extension development or otherwise -
is beyond the scope of this document and is for further study.
2. Overview of Inter-domain Multicast Application Transport
A multicast-based application delivery scenario is as follows:
Tarapore, et al Expires August 3, 2014 [Page 3]
IETF I-D Multicasting Applications Across Peering Points February 2014
o Two independent administrative domains are interconnected via a
peering point.
o The peering point is either multicast enabled (end-to-end
native multicast across the two domains) or it is connected by
one of two possible tunnel types:
o A Generic Routing Encapsulation (GRE) Tunnel [RFC2784]
allowing multicast tunneling across the peering point, or
o An Automatic Multicast Tunnel (AMT) [IETF-ID-AMT].
o The application stream originates at a source in Domain 1.
o An End User associated with Domain 2 requests the application.
It is assumed that the application is suitable for delivery via
multicast means (e.g., live steaming of major events, software
downloads to large numbers of end user devices, etc.)
o The request is communicated to the application source which
provides the relevant multicast delivery information to the EU
device via a "manifest file". At a minimum, this file contains
the {Source, Group} or (S,G) information relevant to the
multicast stream.
o The application client in the EU device then joins the
multicast stream distributed by the application source in
domain 1 utilizing the (S,G) information provided in the
manifest file. The manifest file may also contain additional
information that the application client can use to locate the
source and join the stream.
It should be noted that the second administrative domain - domain 2
- may be an independent network domain (e.g., Tier 1 network
operator domain) or it could also be an Enterprise network operated
by a single customer. The peering point architecture and
requirements may have some unique aspects associated with the
Enterprise case.
The Use Cases describing various architectural configurations for
the multicast distribution along with associated requirements is
described in section 3. Unique aspects related to the Enterprise
network possibility will be described in this section. A
comprehensive list of pertinent information that needs to be
exchanged between the two domains to support various functions
enabling the application transport is provided in section 4.
Tarapore, et al Expires August 3, 2014 [Page 4]
IETF I-D Multicasting Applications Across Peering Points February 2014
3. Inter-domain Peering Point Requirements for Multicast
The transport of applications using multicast requires that the
inter-domain peering point is enabled to support such a process.
There are three possible Use Cases for consideration.
3.1. Native Multicast
This Use Case involves end-to-end Native Multicast between the two
administrative domains and the peering point is also native
multicast enabled - Figure 1.
------------------- -------------------
/ AD-1 \ / AD-2 \
/ (Multicast Enabled) \ / (Multicast Enabled) \
/ \ / \
| +----+ | | |
| | | +------+ | | +------+ | +----+
| | CS |------>| BR |-|---------|->| BR |-------------|-->| EU |
| | | +------+ | I1 | +------+ |I2 +----+
\ +----+ / \ /
\ / \ /
\ / \ /
------------------- -------------------
AD = Administrative Domain (Independent Autonomous System)
CS = Content Multicast Source
BR = Border Router
I1 = AD-1 and AD-2 Multicast Interconnection (MBGP or BGMP)
I2 = AD-2 and EU Multicast Connection
Figure 1 - Content Distribution via End to End Native Multicast
Advantages of this configuration are:
o Most efficient use of bandwidth in both domains
o Fewer devices in the path traversed by the multicast stream
when compared to unicast transmissions.
From the perspective of AD-1, the one disadvantage associated with
native multicast into AD-2 instead of individual unicast to every EU
Tarapore, et al Expires August 3, 2014 [Page 5]
IETF I-D Multicasting Applications Across Peering Points February 2014
in AD-2 is that it does not have the ability to count the number of
End Users as well as the transmitted bytes delivered to them. This
information is relevant from the perspective of customer billing and
operational logs. It is assumed that such data will be collected by
the application layer. The application layer mechanisms for
generating this information need to be robust enough such that all
pertinent requirements for the source provider and the AD operator
are satisfactorily met. The specifics of these methods are beyond
the scope of this document.
Architectural guidelines for this configuration are as follows:
a. Dual homing for peering points between domains is recommended
as a way to ensure reliability with full BGP table visibility.
b. If the peering point between AD-1 and AD-2 is a controlled
network environment, then bandwidth can be allocated
accordingly by the two domains to permit the transit of non-
rate adaptive multicast traffic. If this is not the case, then
it is recommended that the multicast traffic should support
rate-adaption.
c. The sending and receiving of multicast traffic between two
domains is typically determined by local policies associated
with each domain. For example, if AD-1 is a service provider
and AD-2 is an enterprise, then AD-1 may support local policies
for traffic delivery to, but not traffic reception from AD-2.
d. Relevant information on multicast streams delivered to End
Users in AD-2 is assumed to be collected by available
capabilities in the application layer. The precise nature and
formats of the collected information will be determined by
directives from the source owner and the domain operators.
3.2. Peering Point Enabled with GRE Tunnel
The peering point is not native multicast enabled in this Use Case.
There is a Generic Routing Encapsulation Tunnel provisioned over the
peering point. In this case, the interconnection I1 between AD-1 and
AD-2 in Figure 1 is multicast enabled via a Generic Routing
Encapsulation Tunnel (GRE) [RFC2784] and encapsulating the multicast
protocols across the interface. The routing configuration is
basically unchanged: Instead of BGP (SAFI2) across the native IP
Tarapore, et al Expires August 3, 2014 [Page 6]
IETF I-D Multicasting Applications Across Peering Points February 2014
multicast link between AD-1 and AD-2, BGP (SAFI2) is now run across
the GRE tunnel.
Advantages of this configuration:
o Highly efficient use of bandwidth in both domains although not
as efficient as the fully native multicast Use Case.
o Fewer devices in the path traversed by the multicast stream
when compared to unicast transmissions.
o Ability to support only partial IP multicast deployments in AD-
1 and/or AD-2.
o GRE is an existing technology and is relatively simple to
implement.
Disadvantages of this configuration:
o Per Use Case 3.1, current router technology cannot count the
number of end users or the number bytes transmitted.
o GRE tunnel requires manual configuration.
o GRE must be in place prior to stream starting.
o GRE is often left pinned up
Architectural guidelines for this configuration include the
following:
Guidelines (a) through (d) are the same as those described in Use
Case 3.1.
e. GRE tunnels are typically configured manually between peering
points to support multicast delivery between domains.
f. It is recommended that the GRE tunnel (tunnel server)
configuration in the source network is such that it only
advertises the routes to the content sources and not to the
entire network. This practice will prevent unauthorized
delivery of content through the tunnel (e.g., if content is not
part of an agreed CDN partnership).
Tarapore, et al Expires August 3, 2014 [Page 7]
IETF I-D Multicasting Applications Across Peering Points February 2014
3.3. Peering Point Enabled with an AMT - Both Domains Multicast
Enabled
Both administrative domains in this Use Case are assumed to be
native multicast enabled here; however the peering point is not. The
peering point is enabled with an Automatic Multicast Tunnel. The
basic configuration is depicted in Figure 2.
------------------- -------------------
/ AD-1 \ / AD-2 \
/ (Multicast Enabled) \ / (Multicast Enabled) \
/ \ / \
| +----+ | | |
| | | +------+ | | +------+ | +----+
| | CS |------>| AR |-|---------|->| AG |-------------|-->| EU |
| | | +------+ | I1 | +------+ |I2 +----+
\ +----+ / \ /
\ / \ /
\ / \ /
------------------- -------------------
AR = AMT Relay
AG = AMT Gateway
I1 = AMT Interconnection between P-CDN and S-CDN
I2 = S-CDN and EU Multicast Connection
Figure 2 - AMT Interconnection between AD-1 and AD-2
Advantages of this configuration:
o Highly efficient use of bandwidth in AD-1.
o AMT is an existing technology and is relatively simple to
implement. Attractive properties of AMT include the following:
o Dynamic interconnection between Gateway-Relay pair across
the peering point.
o Ability to serve clients and servers with differing
policies.
Disadvantages of this configuration:
Tarapore, et al Expires August 3, 2014 [Page 8]
IETF I-D Multicasting Applications Across Peering Points February 2014
o Per Use Case 3.1 (AD-2 is native multicast), current router
technology cannot count the number of end users or the number
bytes transmitted.
o Additional devices (AMT Gateway and Relay pairs) may be
introduced into the path if these services are not incorporated
in the existing routing nodes.
o Currently undefined mechanisms to select the AR from the AG
automatically.
Architectural guidelines for this configuration are as follows:
Guidelines (a) through (d) are the same as those described in Use
Case 3.1.
e. It is recommended that AMT Relay and Gateway pairs be
configured at the peering points to support multicast delivery
between domains. AMT tunnels will then configure dynamically
across the peering points once the Gateway in AD-2 receives the
(S, G) information from the EU.
3.4. Peering Point Enabled with an AMT - AD-2 Not Multicast Enabled
In this AMT Use Case, the second administrative domain AD-2 is not
multicast enabled. This implies that the interconnection between AD-
2 and the End User is also not multicast enabled as depicted in
Figure 3.
Tarapore, et al Expires August 3, 2014 [Page 9]
IETF I-D Multicasting Applications Across Peering Points February 2014
------------------- -------------------
/ AD-1 \ / AD-2 \
/ (Multicast Enabled) \ / (Non-Multicast \
/ \ / Enabled) \
| +----+ | | |
| | | +------+ | | | +----+
| | CS |------>| AR |-|---------|-----------------------|-->|EU/G|
| | | +------+ | | |I2 +----+
\ +----+ / \ /
\ / \ /
\ / \ /
------------------- -------------------
CS = Content Source
AR = AMT Relay
EU/G = Gateway client embedded in EU device
I2 = AMT Tunnel Connecting EU/G to AR in AD-1 through Non-Multicast
Enabled AD-2.
Figure 3 - AMT Tunnel Connecting AD-1 AMT Relay and EU Gateway
This Use Case is equivalent to having unicast distribution of the
application through AD-2. The total number of AMT tunnels would be
equal to the total number of End Users requesting the application.
The peering point thus needs to accommodate the total number of AMT
tunnels between the two domains. Each AMT tunnel can provide the
data usage associated with each End User.
Advantages of this configuration:
o Highly efficient use of bandwidth in AD-1.
o AMT is an existing technology and is relatively simple to
implement. Attractive properties of AMT include the following:
o Dynamic interconnection between Gateway-Relay pair across
the peering point.
o Ability to serve clients and servers with differing
policies.
o Each AMT tunnel serves as a count for each End User and is also
able to track data usage (bytes) delivered to the EU.
Tarapore, et al Expires August 3, 2014 [Page 10]
IETF I-D Multicasting Applications Across Peering Points February 2014
Disadvantages of this configuration:
o Additional devices (AMT Gateway and Relay pairs) are introduced
into the transport path.
o Assuming multiple peering points between the domains, the EU
Gateway needs to be able to find the "correct" AMT Relay in AD-
1.
Architectural guidelines for this configuration are as follows:
Guidelines (a) through (c) are the same as those described in Use
Case 3.1.
d. It is recommended that proper procedures are implemented such
that the AMT Gateway at the End User device is able to find the
correct AMT Relay in AD-1 across the peering points. The
application client in the EU device is expected to supply the (S,
G) information to the Gateway for this purpose.
e. The AMT tunnel capabilities are expected to be sufficient for
the purpose of collecting relevant information on the multicast
streams delivered to End Users in AD-2.
3.5. AD-2 Not Multicast Enabled - Multiple AMT Tunnels Through AD-2
This is a variation of Use Case 3.4 as follows:
Tarapore, et al Expires August 3, 2014 [Page 11]
IETF I-D Multicasting Applications Across Peering Points February 2014
------------------- -------------------
/ AD-1 \ / AD-2 \
/ (Multicast Enabled) \ / (Non-Multicast \
/ \ / Enabled) \
| +----+ | |+--+ +--+ |
| | | +------+ | ||AG| |AG| | +----+
| | CS |------>| AR |-|-------->||AR|------------->|AR|-|-->|EU/G|
| | | +------+ | I1 ||1 | I2 |2 | |I3 +----+
\ +----+ / \+--+ +--+ /
\ / \ /
\ / \ /
------------------- -------------------
(Note: Diff-marks for the figure have been removed to improve
viewing)
CS = Content Source
AR = AMT Relay in AD-1
AGAR1 = AMT Gateway/Relay node in AD-2 across Peering Point
I1 = AMT Tunnel Connecting AR in AD-1 to GW in AGAR1 in AD-2
AGAR2 = AMT Gateway/Relay node at AD-2 Network Edge
I2 = AMT Tunnel Connecting Relay in AGAR1 to GW in AGAR2
EU/G = Gateway client embedded in EU device
I3 = AMT Tunnel Connecting EU/G to AR in AGAR2
Figure 4 - AMT Tunnel Connecting AD-1 AMT Relay and EU Gateway
Use Case 3.4 results in several long AMT tunnels crossing the entire
network of AD-2 linking the EU device and the AMT Relay in AD-1
through the peering point. Depending on the number of End Users,
there is a likelihood of an unacceptably large number of AMT tunnels
- and unicast streams - through the peering point. This situation
can be alleviated as follows:
o Provisioning of strategically located AMT nodes at the edges of
AD-2. An AMT node comprises co-location of an AMT Gateway and
an AMT Relay. One such node is at the AD-2 side of the peering
point (node AGAR1 in Figure 4).
o Single AMT tunnel established across peering point linking AMT
Relay in AD-1 to the AMT Gateway in the AMT node AGAR1 in AD-2.
o AMT tunnels linking AMT node AGAR1 at peering point in AD-2 to
other AMT nodes located at the edges of AD-2: e.g., AMT tunnel
Tarapore, et al Expires August 3, 2014 [Page 12]
IETF I-D Multicasting Applications Across Peering Points February 2014
I2 linking AMT Relay in AGAR1 to AMT Gateway in AMT node AGAR2
in Figure 4.
o AMT tunnels linking EU device (via Gateway client embedded in
device) and AMT Relay in appropriate AMT node at edge of AD-2:
e.g., I3 linking EU Gateway in device to AMT Relay in AMT node
AGAR2.
The advantage for such a chained set of AMT tunnels is that the
total number of unicast streams across AD-2 is significantly reduced
thus freeing up bandwidth. Additionally, there will be a single
unicast stream across the peering point instead of possibly, an
unacceptably large number of such streams per Use Case 3.4. However,
this implies that several AMT tunnels will need to be dynamically
configured by the various AMT Gateways based solely on the (S,G)
information received from the application client at the EU device. A
suitable mechanism for such dynamic configurations is therefore
critical.
Architectural guidelines for this configuration are as follows:
Guidelines (a) through (c) are the same as those described in Use
Case 3.1.
d. It is recommended that proper procedures are implemented such
that the various AMT Gateways (at the End User devices and the AMT
nodes in AD-2) are able to find the correct AMT Relay in other AMT
nodes as appropriate. The application client in the EU device is
expected to supply the (S, G) information to the Gateway for this
purpose.
e. The AMT tunnel capabilities are expected to be sufficient for
the purpose of collecting relevant information on the multicast
streams delivered to End Users in AD-2.
4. Supporting Functionality
Supporting functions and related interfaces over the peering point
that enable the multicast transport of the application are listed in
this section. Critical information parameters that need to be
exchanged in support of these functions are enumerated along with
guidelines as appropriate. Specific interface functions for
consideration are as follows.
Tarapore, et al Expires August 3, 2014 [Page 13]
IETF I-D Multicasting Applications Across Peering Points February 2014
4.1. Network Interconnection Transport and Security Guidelines
The term "Network Interconnection Transport" refers to the
interconnection points between the two Administrative Domains. The
following is a representative set of attributes that will need to be
agreed to between the two administrative domains to support
multicast delivery.
o Number of Peering Points
o Peering Point Addresses and Locations
o Connection Type - Dedicated for Multicast delivery or shared
with other services
o Connection Mode - Direct connectivity between the two AD's or
via another ISP
o Peering Point Protocol Support - Multicast protocols that will
be used for multicast delivery will need to be supported at
these points. Examples of protocols include eBGP, BGMP, and
MBGP.
o Bandwidth Allocation - If shared with other services, then
there needs to be a determination of the share of bandwidth
reserved for multicast delivery.
o QoS Requirements - Delay/latency specifications that need to be
specified in an SLA.
o AD Roles and Responsibilities - the role played by each AD for
provisioning and maintaining the set of peering points to
support multicast delivery.
From a security perspective, it is expected that normal/typical
security procedures will be followed by each AD to facilitate
multicast delivery to registered and authenticated end users. Some
security aspects for consideration are:
o Encryption - Peering point links may be encrypted per agreement
if dedicated for multicast delivery.
o Security Breach Mitigation Plan - In the event of a security
breach, the two AD's are expected to have a mitigation plan for
shutting down the peering point and directing multicast traffic
Tarapore, et al Expires August 3, 2014 [Page 14]
IETF I-D Multicasting Applications Across Peering Points February 2014
over alternated peering points. It is also expected that
appropriate information will be shared for the purpose of
securing the identified breach.
4.2. Routing Aspects and Related Guidelines
The main objective for multicast delivery routing is to ensure that
the End User receives the multicast stream from the "most optimal"
source [INF_ATIS_10] which typically:
o Maximizes the multicast portion of the transport and minimizes
any unicast portion of the delivery, and
o Minimizes the overall combined network(s) route distance.
This routing objective applies to both Native and AMT; the actual
methodology of the solution will be different for each. Regardless,
the routing solution is expected to be:
o Scalable
o Avoid/minimize new protocol development or modifications, and
o Be robust enough to achieve high reliability and automatically
adjust to changes/problems in the multicast infrastructure.
For both Native and AMT environments, having a source as close as
possible to the EU network is most desirable; therefore, in some
cases, an AD may prefer to have multiple sources near different
peering points, but that is entirely an implementation issue.
4.2.1 Native Multicast Routing Aspects
Native multicast simply requires that the Administrative Domains
coordinate and advertise the correct source address(es) at their
network interconnection peering points(i.e., border routers). An
example of multicast delivery via a Native Multicast process across
two administrative Domains is as follows assuming that the
interconnecting peering points are also multicast enabled:
o Appropriate information is obtained by the EU client who is a
subscriber to AD-2 (see Use Case 3.1). This is usually done via
an appropriate file transfer - this file is typically known as
the manifest file. It contains instructions directing the EU
Tarapore, et al Expires August 3, 2014 [Page 15]
IETF I-D Multicasting Applications Across Peering Points February 2014
client to launch an appropriate application if necessary, and
also additional information for the application about the source
location and the group (or stream) id in the form of the "S,G"
data. The "S" portion provides the name or IP address of the
source of the multicast stream. The file may also contain
alternate delivery information such as specifying the unicast
address of the stream.
o The client uses the join message with S,G to join the multicast
stream [RFC2236].
To facilitate this process, the two AD's need to do the following:
o Advertise the source id(s) over the Peering Points
o Exchange relevant Peering Point information such as Capacity
and Utilization (Other??)
4.2.2 GRE Tunnel over Interconnecting Peering Point
If the interconnecting peering point is not multicast enabled and
both ADs are multicast enabled, then a simple solution is to
provision a GRE tunnel between the two ADs - see Use Case 3.2.2.
The termination points of the tunnel will usually be a network
engineering decision, but generally will be between the border
routers or even between the AD 2 border router and the AD 1 source
(or source access router). The GRE tunnel would allow end-to-end
native multicast or AMT multicast to traverse the interface.
Coordination and advertisement of the source IP is still required.
The two AD's need to follow the same process as described in 4.2.1
to facilitate multicast delivery across the Peering Points.
4.2.3 Routing Aspects with AMT Tunnels
Unlike Native (with or without GRE), an AMT Multicast environment is
more complex. It presents a dual layered problem because there are
two criteria that should be simultaneously meet:
o Find the closest AMT relay to the end-user that also has
multicast connectivity to the content source and
o Minimize the AMT unicast tunnel distance.
There are essentially two components to the AMT specification:
Tarapore, et al Expires August 3, 2014 [Page 16]
IETF I-D Multicasting Applications Across Peering Points February 2014
o AMT Relays: These serve the purpose of tunneling UDP multicast
traffic to the receivers (i.e., End Points). The AMT Relay will
receive the traffic natively from the multicast media source and
will replicate the stream on behalf of the downstream AMT
Gateways, encapsulating the multicast packets into unicast
packets and sending them over the tunnel toward the AMT Gateway.
In addition, the AMT Relay may perform various usage and
activity statistics collection. This results in moving the
replication point closer to the end user, and cuts down on
traffic across the network. Thus, the linear costs of adding
unicast subscribers can be avoided. However, unicast replication
is still required for each requesting endpoint within the
unicast-only network.
o AMT Gateway (GW): The Gateway will reside on an on End-Point -
this may be a Personal Computer (PC) or a Set Top Box (STB). The
AMT Gateway receives join and leave requests from the
Application via an Application Programming Interface (API). In
this manner, the Gateway allows the endpoint to conduct itself
as a true Multicast End-Point. The AMT Gateway will encapsulate
AMT messages into UDP packets and send them through a tunnel
(across the unicast-only infrastructure) to the AMT Relay.
The simplest AMT Use Case (section 3.3) involves peering points that
are not multicast enabled between two multicast enabled ADs. An AMT
tunnel is deployed between an AMT Relay on the AD 1 side of the
peering point and an AMT Gateway on the AD 2 side of the peering
point. One advantage to this arrangement is that the tunnel is
established on an as needed basis and need not be a provisioned
element. The two ADs can coordinate and advertise special AMT Relay
Anycast addresses with each other - though they may alternately
decide to simply provision Relay addresses, though this would not be
a optimal solution in terms of scalability.
Use Cases 3.4 and 3.5 describe more complicated AMT situations as
AD-2 is not multicast enabled. For these cases, the End User device
needs to be able to setup an AMT tunnel in the most optimal manner.
Using an Anycast IP address for AMT Relays allows for all AMT
Gateways to find the "closest" AMT Relay - the nearest edge of the
multicast topology of the source. An example of a basic delivery
via an AMT Multicast process for these two Use Cases is as follows:
o The manifest file is obtained by the EU client application. This
file contains instructions directing the EU client to an ordered
list of particular destinations to seek the requested stream and,
for multicast, specifies the source location and the group (or
stream) ID in the form of the "S,G" data. The "S" portion provides
Tarapore, et al Expires August 3, 2014 [Page 17]
IETF I-D Multicasting Applications Across Peering Points February 2014
the URI (name or IP address) of the source of the multicast stream
and the "G" identifies the particular stream originated by that
source. The manifest file may also contain alternate delivery
information such as the address of the unicast form of the content
to be used, for example, if the multicast stream becomes
unavailable.
o Using the information in the manifest file, and possibly
information provisioned directly in the EU client, a DNS query is
initiated in order to connect the EU client/AMT Gateway to an AMT
Relay.
o Query results are obtained, and may return an Anycast address or a
specific unicast address of a relay. Multiple relays will
typically exist. The Anycast address is a routable "pseudo-
address" shared among the relays that can gain multicast access to
the source.
o If a specific IP address unique to a relay was not obtained, the
AMT Gateway then sends a message (e.g., the discovery message) to
the Anycast address such that the network is making the routing
choice of particular relay - e.g., closest relay to the EU. (Note
that in IPv6 there is a specific Anycast format and Anycast is
inherent in IPv6 routing, whereas in IPv4 Anycast is handled via
provisioning in the network. Details are out of scope for this
document.)
o The contacted AMT Relay then returns its specific unicast IP
address (after which the Anycast address is no longer required).
Variations may exist as well.
o The AMT Gateway uses that unicast IP address to initiate a three-
way handshake with the AMT Relay.
o AMT Gateway provides "S,G" to the AMT Relay (embedded in AMT
protocol messages).
o AMT Relay receives the "S,G" information and uses the S,G to join
the appropriate multicast stream, if it has not already subscribed
to that stream.
o AMT Relay encapsulates the multicast stream into the tunnel
between the Relay and the Gateway, providing the requested content
to the EU.
Tarapore, et al Expires August 3, 2014 [Page 18]
IETF I-D Multicasting Applications Across Peering Points February 2014
Note: Further routing discussion on optimal method to find "best AMT
Relay/GW combination" and information exchange between AD's to be
provided.
4.3. Back Office Functions - Billing and Logging Guidelines
4.4. Operations - Service Performance and Monitoring Guidelines
4.5. Reliability Models/Service Assurance Guidelines
4.6. Provisioning Guidelines
In order to find right relay there is a need for a small/light
implementation of an AMT DNS in source network.
4.7. Client Models
4.8. Addressing Guidelines
5. Security Considerations
(Include discussion on DRM, AAA, Network Security)
Tarapore, et al Expires August 3, 2014 [Page 19]
IETF I-D Multicasting Applications Across Peering Points February 2014
6. IANA Considerations
7. Conclusions
8. References
8.1. Normative References
[RFC2784] D. Farinacci, T. Li, S. Hanks, D. Meyer, P. Traina,
"Generic Routing Encapsulation (GRE)", RFC 2784, March 2000
[IETF-ID-AMT] G. Bumgardner, "Automatic Multicast Tunneling", draft-
ietf-mboned-auto-multicast-13, April 2012, Work in progress
[RFC4604] H. Holbrook, et al, "Using Internet Group Management
Protocol Version 3 (IGMPv3) and Multicast Listener Discovery
Protocol Version 2 (MLDv2) for Source Specific Multicast", RFC 4604,
August 2006
[RFC4607] H. Holbrook, et al, "Source Specific Multicast", RFC 4607,
August 2006
8.2. Informative References
[INF_ATIS_10] "CDN Interconnection Use Cases and Requirements in a
Multi-Party Federation Environment", ATIS Standard A-0200010,
December 2012
9. Acknowledgments
Tarapore, et al Expires August 3, 2014 [Page 20]
IETF I-D Multicasting Applications Across Peering Points February 2014
Authors' Addresses
Percy S. Tarapore
AT&T
Phone: 1-732-420-4172
Email: tarapore@att.com
Robert Sayko
AT&T
Phone: 1-732-420-3292
Email: rs1983@att.com
Greg Shepherd
Cisco
Phone:
Email: shep@cisco.com
Toerless Eckert
Cisco
Phone:
Email: eckert@cisco.com
Ram Krishnan
Brocade
Phone:
Email: ramk@brocade.com
Tarapore, et al Expires August 3, 2014 [Page 21]
