IPPM Working Group H. Wang
Internet Draft J. Li
Intended status: Standards Track China Mobile
Expires: December 25, 2024 C. Lin
New H3C Technologies
X. Min
ZTE Corporation
G. Mirsky
Ericsson
June 26, 2024
Distributed Flow Measurement in IPv6
draft-wang-ippm-ipv6-distributed-flow-measurement-05
Abstract
In IPv6 networks, performance measurements such as packet loss,
delay and jitter of real traffic can be carried out based on the
Alternate-Marking method. Usually, the controller needs to collect
statistical data on network devices, calculate and present the
measurement results. This document proposes a distributed method for
on-path flow measurement, which is independent of the controller.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on December 25, 2024.
Wang, et al. Expires January, 2024 [Page 1]
Internet-Draft Distributed flow measurement In IPv6 January 2024
Copyright Notice
Copyright (c) 2024 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction ................................................ 3
1.1. Requirements Language .................................. 3
2. Requirement scenarios ....................................... 3
3. End-to-end measurement ...................................... 5
4. Hop-by-hop measurement ...................................... 5
5. Extension to the Flow Monitor Option ........................ 6
5.1. Previous period count bit (bit1) ....................... 6
5.2. Packet timestamp bit (bit2) ............................ 6
6. Measurement information and result notification ............. 7
6.1. Data fields ............................................ 8
6.1.1. Base data structure ............................... 8
6.1.2. Packet count TLV .................................. 8
6.1.3. Time Stamp TLV .................................... 9
6.1.4. Packet loss TLV .................................. 10
6.1.5. Packet delay TLV ................................. 11
6.1.6. Average Packet loss TLV .......................... 11
6.1.7. Average Packet delay TLV ......................... 12
6.2. Transport channel ..................................... 13
6.2.1. Independent controller protocol .................. 13
6.2.2. Extending BGP Protocol ........................... 14
6.2.3. Reverse traffic .................................. 14
7. Application of measurement results ......................... 14
8. IANA Considerations ........................................ 15
9. Security Considerations .................................... 15
10. References ................................................ 16
10.1. Normative References ................................. 16
Authors' Addresses ............................................ 17
Wang, et al. Expires July, 2024 [Page 2]
Internet-Draft Distributed flow measurement In IPv6 January 2024
1. Introduction
[draft-wang-ippm-ipv6-flow-measurement] describes how to measure the
network by carrying the detection data in the traffic in the IPv6
network based on Alternate-Marking.
The nodes participating in the measurement need to collect
information such as message statistics and processing time stamps,
and transport the collected information to the controller through
telemetry technology or other methods. The controller calculates the
packet loss and delay of each flow according to the telemetry data.
Based on the basic method of [draft-wang-ippm-ipv6-flow-
measurement], this document proposes a flow measurement without the
participation of the controller. The nodes involved in the
measurement calculate the network metrics such as packet loss and
delay Distributed.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2. Requirement scenarios
The method described in [draft-wang-ippm-ipv6-flow-measurement]
requires the controller to summarize the data collected by each node
and then calculate the final measurement result. In some specific
scenarios, this method could not meet the requirements of
measurement well.
o Scenario1:
For the customers who have high requirements for SLA such as banks
and finance, this method cannot meet the customers well. Firstly,
each participating measuring node reports to the controller, and
then the centralized controller calculates the path quality, and
then the controller notifies the source node to schedule the path of
traffic. The whole processing path is too long and it is difficult
to guarantee the SLA requirements of customers in this way.
o Scenario2:
Wang, et al. Expires July, 2024 [Page 3]
Internet-Draft Distributed flow measurement In IPv6 January 2024
For the transport network with multiple AS domains and multi-level
controllers, one inter-AS controller is deployed and one intra-AS
controller is deployed for each AS typically.
Inter-AS controller programs end-to-end paths, but do not manage
network devices. Each intra-AS controller only manages devices in
its own AS and is not aware of the entire end-to-end path.
Therefore, the measurement data will be reported to the intra-AS
controller by the measurement node, but the final data needs to be
summarized, calculated and presented on the centralized inter-AS
controller. This will cause the interaction between different levels
of controllers to be too complex.
+-------+
inter-AS controller-->| |
+-------+
/ \
/ \
/ \
/ \
Intra-AS +------+ / \ +-------+
controller -->| |---+ +---| |
+------+ +-------+
/ | \ / | \
/ : \ / : \
/ | \ / | \
+-----------------------------+ +----------------------------+
| / | \ | | / | \ |
| +----+ +----+ +----+ | | +----+ +----+ +----+ |
| | +-----+ +---+ +- -------+ +----+ +----+ | |
| +----+ +----+ +----+ | | +----+ +----+ +----+ |
+-----------------------------+ +----------------------------+
AS100 AS200
Figure 1: reference topology of multiple level controller
o Scenario3:
For some networks may not have the conditions or requirements to
deploy controllers, but they also hope to use the technology of flow
measurement to measure and present the quality of traffic forwarding
path.
In order to meet the requirement of these scenarios, this document
proposes a distributed flow measurement, which does not depend on
the controller. All the nodes participating in the measurement
complete the measurement, and finally the measurement results can be
Wang, et al. Expires July, 2024 [Page 4]
Internet-Draft Distributed flow measurement In IPv6 January 2024
used on the source node for fast intelligent routing, simplifying
operation and maintenance, and optimize the experience.
3. End-to-end measurement
For end-to-end measurement, there are two working models, which are
suitable for different scenarios.
o Source node model:
The source node completes the summary and calculation of statistical
data.
The source node inserts the required flow measurement indicators
into the specified traffic, and marks the traffic according to
[draft-wang-ippm-ipv6-flow-measurement]. The end node collects the
statistical data and time stamp, the collected information is
periodically notified to the source node, which completes the
calculation of the measurement results.
In this model, the source node undertakes the work of the controller
and can count the data measured by the traffic through source node.
o End node model:
The end node is responsible for calculating measurement result. In
addition to marking the traffic, the source node also needs to carry
additional information through the flow monitor option. For example,
in order to measure packet loss, the traffic count of the source
node in the previous period need to be carried in the flow monitor
option, packet delay measurement requires the source node to carry a
timestamp when marking the D bit.
Through this information, the end node could calculate the packet
loss and delay stream on the flow. Furthermore, the average packet
loss and delay could be calculated. All the result could be send to
the corresponding source node.
This model is suitable for the scenario of one source node vs
multiple end nodes, such as multicast. It can reduce the calculation
pressure of the source node and transfer the workload to each end
node.
4. Hop-by-hop measurement
Hop-by-hop measurement requires that intermediate nodes also
participate in data collection, so only the source node model should
be used.
Wang, et al. Expires July, 2024 [Page 5]
Internet-Draft Distributed flow measurement In IPv6 January 2024
5. Extension to the Flow Monitor Option
Refer to [draft-wang-ippm-ipv6-flow-measurement], the additional
information required by the end node model can be carried by
extending Ext FM type.
Define the corresponding bit and data format for the packet count of
previous period and time stamp.
0 1 2 3 4 5 6 7 8 9 15
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|1|1|0|0|0|0|0|0|0|0|0|0|0|0|0|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Ext FM type extension
5.1. Previous period count bit (bit1)
This bit indicates the flow monitor option carries the packet count
of the source node in the previous period. The end node can
calculate the packet loss data according to this value in
combination with the locally recorded count.
The data format is shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ PacketCount(64bits) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: PacketCount data format
o PacketCount 64bits Packet count of the previous period of the
source node.
5.2. Packet timestamp bit (bit2)
This bit indicates the flow monitor option carries the timestamp set
by the source node, which is the time when the source node receives
the packet. The end node could calculate the packet delay according
to this value in combination with the packet receiving time of end
node.
The data format is shown below:
Wang, et al. Expires July, 2024 [Page 6]
Internet-Draft Distributed flow measurement In IPv6 January 2024
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TF | RESERVED |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ TimestampSecond(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ TimestampNanoSecond(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: timestamp data format
o TF: 4bits, Timestamp format. The values are as follows:
1: PTP (see [RFC8877])
2: NTP (see [RFC5905])
3: POSIX
o TimestampSecond: 64bits, Integer value of the second part from
1970 to the time when the message is received in the timestamp
format specified by NF field.
o TimestampNanoSecond:64bits, Integer value of the nanosecond part
from 1970 to the time of receiving the message in the timestamp
format specified by NF field.
6. Measurement information and result notification
For the source node model, the measurement data of the intermediate
node and the end node need to be sent to the corresponding source
node.
For the end node model, the end node needs to send the calculated
measurement results to the corresponding source node.
The address of the original node is obtained through the outer
encapsulation source address of the packet carrying the monitor
data. The notification period of collection data or results can be
according to the measurement period or the configured period.
Wang, et al. Expires July, 2024 [Page 7]
Internet-Draft Distributed flow measurement In IPv6 January 2024
6.1. Data fields
The notification data structure includes a base data structure and
multiple data structures defined through TLV.
6.1.1. Base data structure
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NodeMonID | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: Base data field
The fields are defined as following:
o NodeMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
o Length: A 12 bits field, Length of the notification data in 4-
octet units, not including the first 4 octets.
6.1.2. Packet count TLV
This TLV is used to notify packet count to source node and is used
in the source node model. The TLV is defined as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Flags | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FlowMonID | RESERVED |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeriodID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ PacketCount(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: packet count TLV
o Type: A one-octet field. Value 1 will be register in IANA.
o Flags: A one-octet field.
o Length: A two-octet field equal to the length of the Value field
in octets.
Wang, et al. Expires July, 2024 [Page 8]
Internet-Draft Distributed flow measurement In IPv6 January 2024
o FlowMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
o PeriodID: A 4 Octets period ID of the packet count.
o PacketCount: A 8 Octets packet count in the period received by
node.
6.1.3. Time Stamp TLV
This TLV is used to notify time stamp to source node and is used in
the source node model. The tlv is defined as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Flags | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FlowMonID | TF | RESERVED |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeriodID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ TimestampSecond(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ TimestampNanoSecond(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: time stamp TLV
o Type: A one-octet field. Value 2 will be register in IANA.
o Flags: A one-octet field.
o Length: A two-octet field equal to the length of the Value field
in octets.
o FlowMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
o TF: A 4 bits format of Timestamp. The values are as follows:
1: PTP (see [RFC8877])
2: NTP (see [RFC5905])
Wang, et al. Expires July, 2024 [Page 9]
Internet-Draft Distributed flow measurement In IPv6 January 2024
3: POSIX
o PeriodID: A 4 Octets period ID of the packet count.
o TimestampSecond: 64bits, Integer value of the second part from
1970 to the time when the message is received.
o TimestampNanoSecond:64bits, Integer value of the nanosecond part
from 1970 to the time of receiving the message.
Note that if the clocks of nodes participating in flow measurement
are unstable, clock synchronization between nodes is required. The
clock synchronization mechanism used is outside the scope of this
document. For example, NTP clock [RFC5905] or PTP clock [RFC8877]
can be used.
6.1.4. Packet loss TLV
This TLV is used to notify measurement of packet loss to source node
and is used in the end node model. The tlv is defined as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Flags | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FlowMonID | RESERVED |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeriodID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ PacketLoss(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8: packet count TLV
o Type: A one-octet field. Value 3 will be register in IANA.
o Flags: A one-octet field.
o Length: A two-octet field equal to the length of the Value field
in octets.
o FlowMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
Wang, et al. Expires July, 2024 [Page 10]
Internet-Draft Distributed flow measurement In IPv6 January 2024
o PeriodID: A 4 Octets period ID of the packet count.
o PacketLoss: A 8 Octets count of packet loss in the period
specified by periodID.
6.1.5. Packet delay TLV
This TLV is used to notify measurement of packet delay to source
node and is used in the end node model. The tlv is defined as
follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Flags | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FlowMonID | RESERVED |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeriodID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ packetDelay(64bit ) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 9: time stamp TLV
o Type: A one-octet field. Value 4 will be register in IANA.
o Flags: A one-octet field.
o Length: A two-octet field equal to the length of the Value field
in octets.
o FlowMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
o PeriodID: A 4 Octets period ID of the packet count.
o packetDelay: 64bits field of nanosecond, which is the packet
delay in the period specified by PeroidID.
6.1.6. Average Packet loss TLV
This TLV is used to notify measurement of average packet loss to
source node and is used in the end node model. The TLV is defined as
follows:
Wang, et al. Expires July, 2024 [Page 11]
Internet-Draft Distributed flow measurement In IPv6 January 2024
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Flags | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FlowMonID | Periods |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ AveragePacketLoss(64bit) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10: Average packet loss TLV
o Type: A one-octet field. Value 3 will be register in IANA.
o Flags: A one-octet field.
o Length: A two-octet field equal to the length of the Value field
in octets.
o FlowMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
o Periods A 12 bits field, which identifies the number of periods
used to calculate the average packet loss. It can be determined
based on the capacity or configuration of the end node.
o AveragePacketLoss: A 8 Octets count of packet loss, which is the
Average Packet loss in the past periods.
6.1.7. Average Packet delay TLV
This TLV is used to notify measurement of average packet delay to
source node and is used in the end node model. The TLV is defined as
follows:
Wang, et al. Expires July, 2024 [Page 12]
Internet-Draft Distributed flow measurement In IPv6 January 2024
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Flags | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FlowMonID | Periods |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ AveragePacketDelay(64bit ) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11: Average packet delay TLV
o Type: A one-octet field. Value 5 will be register in IANA.
o Flags: A one-octet field.
o Length: A two-octet field equal to the length of the Value field
in octets.
o FlowMonID: A 20 bits field, which is consistent with the
definition in flow monitor option.
o Periods A 12 bits field, which identifies the number of periods
used to calculate the average packet delay. The number of periods
used to calculate the average value could base on the capacity or
configuration of the end node.
o AveragePacketDelay: 64bits field of nanosecond, which is the
Average Packet delay in the past periods.
6.2. Transport channel
The methods used by the data and result notification channels are
out of the scope of this draft, and the following methods can be
considered.
6.2.1. Independent controller protocol
Notify the statistical results or collection data of the source node
through an independent controller protocol. UDP can be considered as
the transport protocol.
A specific UDP port will be registered in IANA in the future for
distributed flow measurement, or the UDP port number can be
Wang, et al. Expires July, 2024 [Page 13]
Internet-Draft Distributed flow measurement In IPv6 January 2024
designated on each node through configuration, such as CLI and
NETCONF.
6.2.2. Extending BGP Protocol
For end-to-end measurement type, only source and end nodes are
involved. In the scenario where BGP is deployed, the collection data
or result can be carried by extending BGP protocol.
This method requires a new definition of BGP measurement address
family, which is used to publish collection data and results.
6.2.3. Reverse traffic
This method is only applicable to end-to-end measurement type too.
The end node could carry the collection data and results to the
source node through reverse data flow.
7. Application of measurement results
Using the distributed flow measurement method described in this
document, the source node can obtain the quality results of the
actual traffic forwarding path faster. According to different actual
needs, the source node could present the measurement results and
optimize the path based on the measurement results, and more other
application.
As illustrated in the figure below, in the SRv6 scenario, the
traffic from CE1 to CE2 requires the SLA of low delay. There are two
paths on PE1 to form a primary-slave relationship.
Path1: PE1->P1->P2->PE2->CE2
Path2: PE1->P3->P4->PE3->CE2
Path1 is the primary path.
Wang, et al. Expires July, 2024 [Page 14]
Internet-Draft Distributed flow measurement In IPv6 January 2024
* * * * * * * * * * * * * * * * * * *
* *
* +----+ +----+ +----+
* +----+ P1 +----+ P2 +-------+ PE2+........
* | +----+ +----+ +----+ :
* | * :
* | * :
* | * :
+----+ +----+ * +----+
+ CE1+.....+ PE1+ * + CE2+
+----+ +----+ * +----+
* | * :
* | +----+ +----+ +----+ :
* +----+ P3 +------+ P4 +------+ PE3+......:
* +----+ +----+ +----+
* *
* * * * * * SRv6 domain * * * * * * *
Figure 12: reference topology
The distributed flow measurement function can be deployed to measure
the quality of the path. PE1, as the source node of the measurement,
adopts the tail node mode. The end nodes PE2 of primary path
complete the calculation of the measurement results and notify PE1.
When PE1 finds out that the delay of path 1 exceeds the threshold,
it can immediately start the switching between the primary and
standby paths, switch the traffic to the standby path, and send an
alarm message. Then, the end node PE3 of standby path continues to
measure the flow and notifies PE1 of the measurement results.
More kinds of applications based on measure results on source nodes
are not in the scope of this document.
8. IANA Considerations
TBD
9. Security Considerations
The potential security threats of Alternate-Marking method have been
described in detail in Section 10 of [I-D.draft-ietf-ippm-
rfc8321bis]. The performance measurement method described in this
document does not introduce additional new security issues.
Wang, et al. Expires July, 2024 [Page 15]
Internet-Draft Distributed flow measurement In IPv6 January 2024
10. References
10.1. Normative References
[I-D.wang-ippm-ipv6-flow-measurement]Wang, H.,Liu, Y., Lin, C.,
Xiao, M., "Flow Measurement in IPv6 Network", draft-wang-
ippm-ipv6-flow-measurement-02(work in progress), August
2022.
[I-D.ietf-6man-ipv6-alt-mark]Fioccola, G., Zhou, T., Cociglio, M.,
Qin, F., and R.Pang, "IPv6 Application of the Alternate
Marking Method",draft-ietf-6man-ipv6-alt-mark-16 (work in
progress), July 2022.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI
10.17487/RFC2119, March 1997, <https://www.rfc-
editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[I-D.draft-ietf-ippm-rfc8321bis] Fioccola, G., Ed., Cociglio, M.,
Mirsky, G., Mizrahi, T., Zhou, T., "Alternate-Marking
Method", draft-ietf-ippm-rfc8321bis-03 (work in progress),
July 2022.
[RFC8877] Mizrahi, T., Fabini, J., and A. Morton, "Guidelines for
Defining Packet Timestamps", RFC 8877,
DOI 10.17487/RFC8877, September 2020,
<https://www.rfc-editor.org/info/rfc8877>.
[RFC5905] Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
"Network Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010,
<https://www.rfc-editor.org/info/rfc5905>.
Wang, et al. Expires July, 2024 [Page 16]
Internet-Draft Distributed flow measurement In IPv6 January 2024
Authors' Addresses
Haojie Wang
China Mobile
Beijing
China
Email: wanghaojie@chinamobile.com
Jinming Li
China Mobile
32 Xuanwumen West Street
Beijing
Xicheng District, 100053
China
Email: lijinming@chinamobile.com
Changwang Lin
New H3C Corporation
Beijing
China
Email: linchangwang.04414@h3c.com
Xiao Min
ZTE Corporation
Beijing
China
Email: xiao.min2@zte.com.cn
Greg Mirsky
Ericsson
Email: gregimirsky@gmail.com
Wang, et al. Expires July, 2024 [Page 17]