Internet Engineering Task Force IJ. Wijnands, Ed.
Internet-Draft Cisco Systems, Inc.
Intended status: Standards Track E. Rosen, Ed.
Expires: April 19, 2015 Juniper Networks, Inc.
A. Dolganow
Alcatel-Lucent
J. Tantsura
Ericsson
S. Aldrin
Huawei Technologies
October 16, 2014
Encapsulation for Bit Index Explicit Replication in MPLS Networks
draft-wijnands-mpls-bier-encapsulation-01
Abstract
Bit Index Explicit Replication (BIER) is an architecture that
provides optimal multicast forwarding through a "multicast domain",
without requiring intermediate routers to maintain any per-flow state
or to engage in an explicit tree-building protocol. When a multicast
data packet enters the domain, the ingress router determines the set
of egress routers to which the packet needs to be sent. The ingress
router then encapsulates the packet in a BIER header. The BIER
header contains a bitstring in which each bit represents exactly one
egress router in the domain; to forward the packet to a given set of
egress routers, the bits corresponding to those routers are set in
the BIER header. The details of the encapsulation depend on the type
of network used to realize the multicast domain. This document
specifies the BIER encapsulation to be used in an MPLS network.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 19, 2015.
Wijnands, et al. Expires April 19, 2015 [Page 1]
Internet-Draft BIER MPLS Encapsulation October 2014
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. The BIER-MPLS Label . . . . . . . . . . . . . . . . . . . . . 3
3. BIER Header . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Imposing and Processing the BIER Encapsulation . . . . . . . 6
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
6. Security Considerations . . . . . . . . . . . . . . . . . . . 8
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8
8. Contributor Addresses . . . . . . . . . . . . . . . . . . . . 8
9. Normative References . . . . . . . . . . . . . . . . . . . . 10
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10
1. Introduction
[BIER_ARCH] describes a new architecture for the forwarding of
multicast data packets. That architecture provides optimal
forwarding of multicast data packets through a "multicast domain".
However, it does not require any explicit tree-building protocol, and
does not require intermediate nodes to maintain any per-flow state.
That architecture is known as "Bit Index Explicit Replication"
(BIER).
This document will use terminology defined in [BIER_ARCH].
A router that supports BIER is known as a "Bit-Forwarding Router"
(BFR). A "BIER domain" is a connected set of Bit-Forwarding Routers
(BFRs), each of which has been assigned a BFR-prefix. A BFR-prefix
is a routable IP address of a BFR, and is used by BIER to identify a
BFR. A packet enters a BIER domain at an ingress BFR (BFIR), and
leaves the BIER domain at one or more egress BFRs (BFERs). Each BFER
must have a BFR-id as well as a BFR-prefix. A BFR-id is just a
Wijnands, et al. Expires April 19, 2015 [Page 2]
Internet-Draft BIER MPLS Encapsulation October 2014
number in the range [1,65535] that, within a BIER domain, identifies
a BFER uniquely.
As described in [BIER_ARCH], BIER requires that multicast data
packets be encapsulated with a header that carries the information
needed to support the BIER forwarding procedures. This information
includes a Set-Id (SI) and a BitString. Together the SI and the
BitString identify the set of BFERs to which the packet must be
delivered.
This document is applicable when a given BIER domain is both an IGP
domain and an MPLS network. In this environment, the BIER
encapsulation consists of two components:
o an MPLS label (which we will call the "BIER-MPLS label"); this
label appears at the bottom of a packet's MPLS label stack.
o a BIER header, as specified in Section 3.
Following the BIER header is the "payload". The payload may be an
IPv4 packet, an IPv6 packet, an ethernet frame, or an MPLS packet.
If it is an MPLS packet, then an MPLS label stack immediately follows
the BIER header. The top label of this MPLS label stack may be
either a downstream-assigned label ([RFC3032]) or an upstream-
assigned label ([RFC5331]. The BIER header contains information
identifying the type of the payload.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. The BIER-MPLS Label
As stated in [BIER_ARCH], when a BIER domain is also an IGP domain,
IGP extensions can be used by each BFR to advertise the BFR-id and
BFR-prefix. The extensions for OSPF are given in [BIER_OSPF].
When a particular BIER domain is both an IGP domain and an MPLS
network, we assume that each BFR will also use IGP extensions to
advertise a set of one or more "BIER-MPLS" labels. When the domain
contains a single "routing underlay" (see [BIER_ARCH]), a given BFR
needs to advertise one such label for each SI. If the domain
contains multiple routing underlays, a given BFR needs to advertise
one such label per SI per each underlay in which that BFR has
adjacencies.
The BIER-MPLS labels are locally significant (i.e., unique only to
the BFR that advertises them) downstream-assigned MPLS labels. For
Wijnands, et al. Expires April 19, 2015 [Page 3]
Internet-Draft BIER MPLS Encapsulation October 2014
example, suppose there is a single routing underlay, the network is
using a BitStringLength of 255, and that all BFERs in the domain have
BFR-ids in the range [1,512]. Since each BIER BitString is 256 bits
long, this requires the use of two SIs: SI=0 and SI=1. So each BFR
will advertise, via IGP extensions, two MPLS labels for BIER: one
corresponding to SI=0 and one corresponding to SI=1.
When a BFR receives an MPLS packet with one of its BIER-MPLS labels
at the top of the stack, it will assume that a BIER header (see
Section 3) immediately follows the stack. It will also infer the
packet's SI from the label.
3. BIER Header
The BIER header is shown in Figure 1. This header appears after the
end of the MPLS label stack, immediately after the MPLS-BIER label.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 0| Ver |I|0 0 0 0 0 0 0| Proto | Len | Entropy |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BitString (first 32 bits) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ BitString (last 32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| BFIR-id (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: BIER Header
First nibble:
The first 4 bits of the header are all set to zero; this ensures
that the BIER header will not be confused with an IP header.
Ver:
This 4-bit field identifies the version of the BIER header. This
document specifies version 0 of the BIER header.
I:
This bit is set if and only if header contains the BFIR-id field.
If this bit is clear, the header does not contain the BFIR-id, and
the header ends at the end of the BitString.
Wijnands, et al. Expires April 19, 2015 [Page 4]
Internet-Draft BIER MPLS Encapsulation October 2014
Proto:
This 4-bit field identifies the type of the payload. (The
"payload" is the packet or frame immediately following the BIER
header.) The protocol field may take any of the following values:
1: MPLS packet with downstream-assigned label at top of stack.
2: MPLS packet with upstream-assigned label at top of stack (see
[RFC5331]). If this value of the Proto field is used, the I
bit MUST be set, and the BFR-id of the BFIR must be placed in
the BFIR-id field. The BFIR-id provides the "context" in which
the upstream-assigned label is interpreted.
3: Ethernet frame.
4: IPv4 packet.
6: IPv6 packet.
Len:
This 4-bit field encodes the length in bits of the BitString. If
k is the length of the BitString, the value of this field is
log2(k)-5. However, only certain values are supported:
1: 64 bits
2: 128 bits
3: 256 bits
4: 512 bits
5: 1024 bits
6: 2048 bits
7: 4096 bits
All other values of this field are illegal.
Entropy:
This 8-bit field specifies an "entropy" value that can be used for
load balancing purposes. The BIER forwarding process may do equal
cost load balancing, but the load balancing procedure MUST choose
the same path for any two packets have the same entropy value.
Wijnands, et al. Expires April 19, 2015 [Page 5]
Internet-Draft BIER MPLS Encapsulation October 2014
If a BFIR is encapsulating (as the payload) MPLS packets that have
entropy labels, the BFIR MUST ensure that if two such packets have
the same MPLS entropy label, they also have the same value of the
BIER entropy field.
BitString:
The BitString that, together with the packet's SI, identifies the
destination BFERs for this packet. Note that the SI for the
packet is inferred from the BIER-MPLS label that precedes the BIER
header.
BFIR-id
This is the BFR-id of the BFIR. The BFR-id is encoded in the
32-bit field as an unsigned integer in the range [1,65535].
This field is optional, and is present only when the I bit is set.
4. Imposing and Processing the BIER Encapsulation
When a BFIR receives a multicast packet from outside the BIER domain,
it carries out the following procedure:
1. By consulting the "multicast flow layer" ([BIER_ARCH]), it
determines the value of the "Proto" field.
2. By consulting the "multicast flow layer", it determines the set
of BFERs that must receive the packet.
3. The BFIR looks up the BFR-id of each of those BFERs.
4. The BFIR converts each such BFR-id into (SI, BitString) format,
as described in [BIER_ARCH].
5. All such BFR-ids that have the same SI can be encoded into the
same BitString. Details of this encoding can be found in
[BIER_ARCH]. For each distinct SI that occurs in the list of the
packet's destination BFERs:
a. The BFIR make a copy of the multicast data packet, and
encapsulates the copy in a BIER header (see Section 3). The
BIER header contains the BitString that represents all the
destination BFERs whose BFR-ids correspond to the given SI.
b. If the payload is an MPLS packet whose label stack begins
with an upstream-assigned label, the BFIR-id field MUST be
present. (Whether a particular MPLS packet payload begins
Wijnands, et al. Expires April 19, 2015 [Page 6]
Internet-Draft BIER MPLS Encapsulation October 2014
with an upstream-assigned label is learned from the
multicast flow layer.) The BFIR-id MAY be included in other
cases as well.
c. The BFIR then applies to that copy the forwarding procedure
of [BIER_ARCH]. This may result in one or more copies of
the packet (possibly with a modified BitString) being
transmitted to a neighboring BFR.
d. Before transmitting a copy of the packet to a neighboring
BFR, the BFIR finds the BIER-MPLS label that was advertised
by the neighbor as corresponding to the given SI. An MPLS
label stack is then preprended to the packet. This label
stack [RFC3032] will contain one label, the aforementioned
BIER-MPLS label. The "S" bit MUST be set, indicating the
end of the MPLS label stack. The packet may then be
transmitted to the neighboring BFR. (This may result in
additional MPLS labels being pushed on the stack. For
example, if an RSVP-TE tunnel is used to transmit packets to
the neighbor, a label representing that tunnel would be
pushed onto the stack.)
When an intermediate BFR receives a packet with one of its own BIER-
MPLS labels at the top of the label stack, it infers the SI from the
label, and follows the forwarding procedures of [BIER_ARCH]. If it
forwards a copy of the packet to a neighboring BFR, it first swaps
the label at the top of the label stack with the BIER-MPLS label that
the neighbor advertised that corresponds to the same SI and routing
underlay.
Thus a BIER-encapsulated packet in an MPLS network consists of a
packet that has:
o An MPLS label stack with a BIER-MPLS label at the bottom of the
stack.
o A BIER header, as described in Section 3.
o The payload, a multicast data packet.
The payload may be an IPv4 packet, an IPv6 packet, an ethernet frame,
or an MPLS packet. If it is an MPLS packet, the BIER header is
followed by a second MPLS label stack; this stack is separate from
the stack that precedes the BIER header.
Wijnands, et al. Expires April 19, 2015 [Page 7]
Internet-Draft BIER MPLS Encapsulation October 2014
5. IANA Considerations
This document has no actions for IANA.
6. Security Considerations
As this document makes use of MPLS, it inherits any security
considerations that apply to the use of the MPLS data plane.
As this document makes use of IGP extensions, it inherits any
security considerations that apply to the IGP.
The security considerations of [BIER_ARCH] also apply.
7. Acknowledgements
The authors wish to thank Rajiv Asati, John Bettink, Nagendra Kumar,
Christian Martin, Neale Ranns, Greg Shepherd, and Ramji Vaithianathan
for their ideas and contributions to this work.
8. Contributor Addresses
Below is a list of other contributing authors in alphabetical order:
Wijnands, et al. Expires April 19, 2015 [Page 8]
Internet-Draft BIER MPLS Encapsulation October 2014
Mach (Guoyi) Chen
Huawei
Email: mach.chen@huawei.com
Arkadiy Gulko
Thomson Reuters
195 Broadway
New York NY 10007
US
Email: arkadiy.gulko@thomsonreuters.com
Wim Henderickx
Alcatel-Lucent
Copernicuslaan 50
Antwerp 2018
BE
Email: wim.henderickx@alcatel-lucent.com
Martin Horneffer
Deutsche Telekom
Hammer Str. 216-226
Muenster 48153
DE
Email: Martin.Horneffer@telekom.de
Uwe Joorde
Deutsche Telekom
Hammer Str. 216-226
Muenster D-48153
DE
Email: Uwe.Joorde@telekom.de
Tony Przygienda
Ericsson
300 Holger Way
San Jose, CA 95134
US
Email: antoni.przygienda@ericsson.com
Wijnands, et al. Expires April 19, 2015 [Page 9]
Internet-Draft BIER MPLS Encapsulation October 2014
9. Normative References
[BIER_ARCH]
Wijnands, IJ., "Multicast using Bit Index Explicit
Replication Architecture", internet-draft draft-wijnands-
bier-architecture-00, September 2014.
[BIER_OSPF]
Psenak, P., Kumar, N., and IJ. Wijnands, "OSPF Extensions
for Bit Index Explicit Replication", internet-draft draft-
psenak-ospf-bier-extensions-00.txt, September 2014.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, January 2001.
[RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
Label Assignment and Context-Specific Label Space", RFC
5331, August 2008.
Authors' Addresses
IJsbrand Wijnands (editor)
Cisco Systems, Inc.
De Kleetlaan 6a
Diegem 1831
BE
Email: ice@cisco.com
Eric C. Rosen (editor)
Juniper Networks, Inc.
10 Technology Park Drive
Westford, Massachusetts 01886
US
Email: erosen@juniper.net
Wijnands, et al. Expires April 19, 2015 [Page 10]
Internet-Draft BIER MPLS Encapsulation October 2014
Andrew Dolganow
Alcatel-Lucent
600 March Rd.
Ottawa, Ontario K2K 2E6
CA
Email: andrew.dolganow@alcatel-lucent.com
Jeff Tantsura
Ericsson
300 Holger Way
San Jose, California 95134
US
Email: jeff.tantsura@ericsson.com
Sam K Aldrin
Huawei Technologies
2330 Central Express Way
Santa Clara, California
US
Email: aldrin.ietf@gmail.com
Wijnands, et al. Expires April 19, 2015 [Page 11]