MMUSIC D. Wing
Internet-Draft T. Reddy
Intended status: Standards Track P. Patil
Expires: March 31, 2014 P. Martinsen
Cisco
September 27, 2013
Mobility with ICE (MICE)
draft-wing-mmusic-ice-mobility-05
Abstract
This specification describes how endpoint mobility can be achieved
using ICE. Two mechanisms are shown, one where both endpoints
support MICE and another where only one endpoint supports MICE.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 31, 2014.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Wing, et al. Expires March 31, 2014 [Page 1]
Internet-Draft MICE September 2013
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Notational Conventions . . . . . . . . . . . . . . . . . . . 3
3. Break Before Make . . . . . . . . . . . . . . . . . . . . . . 4
3.1. Absence of other interfaces in Valid list . . . . . . . . 5
3.1.1. Receiving ICE Mobility event . . . . . . . . . . . . 6
3.2. Keeping unused relayed candidates active . . . . . . . . 7
3.3. New STUN Attributes . . . . . . . . . . . . . . . . . . . 8
4. Make Before Break . . . . . . . . . . . . . . . . . . . . . . 8
5. Mobility using TURN . . . . . . . . . . . . . . . . . . . . . 8
5.1. Creating an Allocation . . . . . . . . . . . . . . . . . 9
5.1.1. Sending an Allocate Request . . . . . . . . . . . . . 10
5.1.2. Receiving an Allocate Request . . . . . . . . . . . . 10
5.1.3. Receiving an Allocate Success Response . . . . . . . 10
5.1.4. Receiving an Allocate Error Response . . . . . . . . 10
5.2. Refreshing an Allocation . . . . . . . . . . . . . . . . 11
5.2.1. Sending a Refresh Request . . . . . . . . . . . . . . 11
5.2.2. Receiving a Refresh Request . . . . . . . . . . . . . 11
5.2.3. Receiving a Refresh Response . . . . . . . . . . . . 12
5.3. New STUN Attribute MOBILITY-TICKET . . . . . . . . . . . 12
5.4. New STUN Error Response Code . . . . . . . . . . . . . . 12
6. Comparison to ICE Restart and Trickle ICE . . . . . . . . . . 12
6.1. Break Before Make - ICE Restart . . . . . . . . . . . . . 12
6.2. Break Before Make - Trickle ICE . . . . . . . . . . . . . 13
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14
8. Security Considerations . . . . . . . . . . . . . . . . . . . 14
8.1. Considerations for ICE mechanism . . . . . . . . . . . . 14
8.2. Considerations for TURN mechanism . . . . . . . . . . . . 15
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 15
10. Change History . . . . . . . . . . . . . . . . . . . . . . . 15
10.1. Changes from draft-wing-mmusic-ice-mobility-00 to -01 . 15
10.2. Changes from draft-wing-mmusic-ice-mobility-01 to -02 . 15
10.3. Changes from draft-wing-mmusic-ice-mobility-02 to -03 . 15
10.4. Changes from draft-wing-mmusic-ice-mobility-03 to -04 . 15
10.5. Changes from draft-wing-mmusic-ice-mobility-04 to -05 . 15
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 16
11.1. Normative References . . . . . . . . . . . . . . . . . . 16
11.2. Informative References . . . . . . . . . . . . . . . . . 16
Appendix A. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
A.1. Presence of other interfaces in Valid list . . . . . . . 17
A.1.1. Receiving ICE Mobility event . . . . . . . . . . . . 18
A.2. Losing an Interface . . . . . . . . . . . . . . . . . . . 18
A.2.1. Keeping unused candidates in the valid list active . 18
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 19
1. Introduction
Wing, et al. Expires March 31, 2014 [Page 2]
Internet-Draft MICE September 2013
When moving between networks, an endpoint has to change its IP
address. This change breaks upper layer protocols such as TCP and
RTP. Various techniques exist to prevent this breakage, all tied to
making the endpoint's IP address static (e.g., Mobile IP, Proxy
Mobile IP, LISP). Other techniques exist, which make the upper layer
protocol ambivalent to IP address changes (e.g., SCTP). The
mechanisms described in this document are in that last category.
ICE [RFC5245] ensures two endpoints have a working media path between
them, and is typically used by Internet-connected interactive media
systems (e.g., SIP endpoints). ICE does not expect either the local
host or the remote host to change their IP addresses. Although ICE
does allow an "ICE restart", this is done by sending a re-INVITE
which goes over the SIP signaling path. The SIP signaling path is
often slower than the media path (which needs to be recovered as
quickly as possible), consumes an extra half round trip, and incurs
an additional delay if the mobility event forces the endpoint to re-
connect with its SIP proxy. When a device changes its IP address, it
is necessary for it to re-establish connectivity with its SIP proxy,
which can be performed in parallel with the steps described in this
document. This document describes how mobility is performed entirely
in the media path, without the additional delay of re-establishing
SIP connectivity, issuing a new offer/answer, or the complications of
multiple SIP offers. This document considers re-establishing bi-
directional media the most critical aspect of a successful mobility
event, and its efforts are towards meeting that goal.
A TURN [RFC5766] server relays media packets and is used for a
variety of purposes, including overcoming NAT and firewall traversal
issues and IP address privacy. The existing TURN specification does
not allow the client address to change, especially if multiple
clients share the same TURN username (e.g., the same credentials are
used on multiple devices).
This document proposes two mechanisms to achieve RTP mobility: a
mechanism where both endpoints support MICE, and a mechanism where
only one endpoint supports MICE. When both endpoints support MICE,
ICE itself can be used to provide mobility. When only one endpoint
supports MICE, a TURN server provides mobility. Both mobility
techniques work across and between network types (e.g., between 3G
and wired Internet access), so long as the client can still access
the remote ICE peer or TURN server.
Readers are assumed to be familiar with ICE [RFC5245].
2. Notational Conventions
Wing, et al. Expires March 31, 2014 [Page 3]
Internet-Draft MICE September 2013
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
This note uses terminology defined in [RFC5245], and the following
additional terminology:
Break Before Make: The initially selected interface for
communication may become unavailable (e.g due to loss of coverage
when moving out of a WiFi hotspot) and new interfaces may become
available due to administrative action (e.g manual activation of a
specific connectivity technology) or due to dynamic conditions
(e.g. Entering coverage area of a wireless network).
Make Before Break: The initially selected interface for
communication may become deprioritized (e.g new interface becoming
available and it's per bit cost is cheaper and the connection
speed is faster than existing interface used for communication).
Simultaneous Mobility: If both the endpoints are mobile and roam at
the same time between networks.
3. Break Before Make
When both endpoints support ICE, ICE itself can provide mobility
functions. One of the primary aspects of ICE is its address
gathering, wherein ICE has each endpoint determine all of the IP
addresses and ports that might be usable for that endpoint and
communicate that list of addresses and ports to its peer, usually
over SDP. That enables the next primary aspect of ICE, which is its
connectivity checks: each ICE endpoint sends a connectivity check
from a checklist created by the local and remote candidates exchanged
in the initial offer/answer exchange. When the ICE endpoint checks
the mapped address from the STUN response during ICE connectivity
checks and finds that the transport address does not match any of the
local candidates that the ICE agent knows about, the mapped address
represents a new candidate -- a peer reflexive candidate. This will
cause the endpoint to construct a new pair and insert it into the
local checklist (Section 7.2.1.3 of [RFC5245]). ICE Mobility (MICE)
takes advantage of that existing ICE functionality to provide faster
mobility.
Endpoints that support ICE Mobility perform ICE normally, and MUST
also include the MOBILITY-SUPPORT attribute in all of their STUN
requests and their STUN responses. The inclusion of this attribute
allows the ICE peer to determine if it can achieve mobility using ICE
or needs to use TURN. To force the use of TURN to achieve ICE
mobility, the ICE endpoint SHOULD NOT respond to ICE connectivity
Wing, et al. Expires March 31, 2014 [Page 4]
Internet-Draft MICE September 2013
checks that have an IP address and port different from the TURN
server, unless those connectivity checks contain the MOBILITY-SUPPORT
attribute. In this way, the remote peer will think those other
candidates are invalid (because its connectivity checks did not
succeed).
After concluding ICE and moving to the ICE completed state (see
Section 8 of [RFC5245]) either endpoint or both endpoints can
initiate ICE Mobility, no matter if it was the Controlling Agent or
the Controlled Agent during normal ICE processing.
3.1. Absence of other interfaces in Valid list
When the interface currently being used for communication becomes
unavailable then ICE agent acquires a list of interfaces that are
available and based on the locally configured host policy
preferences, the ICE endpoint performs ICE Mobility using one of the
available interfaces. In this case local candidates from the
selected interface are not present in the valid list. ICE Mobility
is performed by:
1. The ICE agent remembers the remote host/server reflexive/peer
reflexive candidates for each component of the media streams
previously used from the valid list before clearing its ICE check
list and ICE Valid List.
2. The ICE endpoint gathers host candidates of the same address
family as the remote peer on the new interface, forms a check
list by creating candidate pairs with local host candidates and
remote host/server-reflexive candidates collected in step 1,
performs "Computing Pair Priority and Ordering Pairs"
(Section 5.7.2 of [RFC5245]), "Pruning the Pairs" (Section 5.7.3
of [RFC5245], "Computing states" (Section 5.7.4 of [RFC5245]).
3. The ICE endpoint initiates ICE connectivity checks on those
candidates from the check list in the previous step, and includes
the MOBILITY-EVENT attribute in those connectivity checks.
4. The ICE endpoint acts as controlling agent and the ICE
connectivity check from the previous step SHOULD also include the
USE-CANDIDATE attribute to signal an aggressive nomination (see
Section 2.6 of [RFC5245]).
5. The ICE endpoint performs "Discovering Peer Reflexive Candidates"
(Section 7.1.3.2.1 of [RFC5245]), "Constructing a Valid Pair"
(Section 7.1.3.2.2 of [RFC5245]), "Updating Pair States"
(Section 7.1.3.2.3 of [RFC5245]), and "Updating the Nominated
Flag" (Section 7.1.3.2.4 of [RFC5245]). When the valid list
Wing, et al. Expires March 31, 2014 [Page 5]
Internet-Draft MICE September 2013
contains a candidate pair for each component then ICE processing
is considered complete for the media stream and ICE agent can
start sending media using the nominated candidate pair.
6. Once ICE connectivity checks for all of the media streams are
completed, the controlling ICE endpoint follows the procedures in
Section 11.1 of [RFC5245], specifically to send updated offer if
the candidates in the m and c lines for the media stream (called
the DEFAULT CANDIDATES) do not match ICE's SELECTED CANDIDATES
(also see Appendix B.9 of [RFC5245]).
The ICE endpoint even after Mobility using ICE is successful can
issue an updated offer indicating ICE restart if connectivity checks
using higher priority candidate pairs are not successful.
Mobility using ICE could fail in case of Simultaneous Mobility or if
the ICE peer is behind NAT that performs Address-Dependent Filtering
(see Section 5 of [RFC5245]). Hence the ICE endpoint in parallel
will re-establish connection with the SIP proxy. It will then
determine whether to initiate ICE restart under the following
conditions:
a. After re-establishing connection with the SIP proxy and before
sending new offer to initiate ICE restart if Mobility using ICE
is successful then stop sending the new offer.
b. After successful negotiation of updated offer/answer to initiate
ICE restart, proceed with ICE restart and stop Mobility using ICE
if ICE checks are in the Running/Failed states or ICE is
partially successful and not yet reached ICE complete state.
It's not implementation friendly to have to two checks running in
parallel. ICE restart can re-use partial successful ICE
connectivity check results from Mobility using ICE if required as
optimization.
3.1.1. Receiving ICE Mobility event
A STUN Binding Request containing the MOBILITY-EVENT attribute MAY be
received by an ICE endpoint. The agent MUST use short-term
credential to authenticate the STUN request containing the MOBILITY-
EVENT attribute and perform a message integrity check. The ICE
endpoint will generate STUN Binding Response containing the MOBILE-
SUPPORT attribute and the ICE agent takes role of controlled agent.
If STUN Request containing the MOBILITY-EVENT attribute is received
before the endpoint is in the ICE Completed state, it should be
silently discarded.
Wing, et al. Expires March 31, 2014 [Page 6]
Internet-Draft MICE September 2013
The agent remembers the highest-priority nominated pairs in the Valid
list for each component of the media stream, called the previous
selected pairs before removing all the selected candidate pairs from
the Valid List . It continues sending media to that address until it
finishes with the steps described below. Because those packets might
not be received due to the mobility event, it MAY cache a copy of
those packets.
1. The ICE endpoint constructs a pair whose local candidate is equal
to the transport address on which the STUN request was received
with MOBILITY-EVENT, USE-CANDIDATE attributes and a remote
candidate equal to the source transport address where the STUN
request came from.
2. The ICE endpoint will add this pair to the valid list if not
already present.
3. The agent sets the nominated flag for that pair in the valid pair
to true. ICE processing is considered complete for a media
stream if the valid list contains a selected candidate pair for
each component and ICE agent can start sending media.
The ICE endpoint will follow Steps 1 to 3 when subsequent STUN
Binding Requests are received with MOBILITY-EVENT and USE-CANDIDATE
attributes.
3.2. Keeping unused relayed candidates active
The ICE endpoints can maintain the relayed candidates active even
when not actively used, so that relayed candidates can be tried if
ICE connectivity checks using other candidate types fails. The ICE
agent will have to create permissions in the TURN server for the
remote relayed candidate IP addresses and perform the following
steps:
1. The ICE agent will keep the relayed candidates alive using
Refresh transaction, as described in [RFC5766].
2. When the endpoint IP address changes due to mobility, the ICE
agent will refresh it's allocation with TURN server using
Section 5.2.
3. The ICE agent will pair local and remote relayed candidates for
connectivity checks when performing the steps in Section 3.1.
4. If the ICE connectivity check succeeds only with local and remote
relayed candidates, it suggests that either other peer is roaming
at the same time or is behind Address-Dependent Filtering NAT.
Wing, et al. Expires March 31, 2014 [Page 7]
Internet-Draft MICE September 2013
The ICE agent adds the relayed candidate pair to the valid list
and marks it as selected. The ICE agent can now send media using
the newly selected relayed candidate pair. The Mobile device
must re-establish connection with SIP proxy, issue an updated
offer indicating ICE restart so that media can switched to
higher-priority candidate pairs.
This approach assists Mobility using ICE to succeed but brings in
additional overhead of maintaining relayed candidates.In case of
Simultaneous Mobility, host candidates can change for both the
endpoints by maintaining relayed candidates and using Section 5 media
session can be established using the relayed candidate pair.
3.3. New STUN Attributes
Three new attributes are defined by this section: MOBILITY-EVENT,
MOBILITY-SUPPORT.
The MOBILITY-EVENT attribute indicate the sender experienced a
mobility event. This attribute has no value, thus the attribute
length field MUST always be 0. Rules for sending and interpretation
of receiving are described above.
The MOBILITY-SUPPORT attribute indicates the sender supports ICE
Mobility, as defined in this document. This attribute has no value,
thus the attribute length field MUST always be 0. Rules for sending
and interpretation of receiving are described above.
4. Make Before Break
When a new interface comes up and initially selected interface
becomes deprioritized (e.g due to a low cost interface becoming
available). The ICE endpoint re-connects to the SIP proxy using the
new interface, gather candidates, exchange updated offer/exchange to
restart ICE. Once ICE processing has reached the Completed state
then the ICE endpoint can successfully switch the media over to the
new interface. The interface initially used for communication can
now be turned off without disrupting communications.
5. Mobility using TURN
To achieve mobility, a TURN client should be able to retain an
allocation on the TURN server across changes in the client IP address
as a consequence of movement to other networks.
When the client sends the initial Allocate request to the TURN
server, it will also include the new STUN attribute MOBILITY-TICKET
(with zero length value), which indicates that the client is capable
Wing, et al. Expires March 31, 2014 [Page 8]
Internet-Draft MICE September 2013
of mobility and desires a ticket. The TURN server provisions a
ticket that is sent inside the new STUN attribute MOBILITY-TICKET in
the Allocate Success response to the client. The ticket will be used
by the client when it wants to refresh the allocation but with a new
client IP address and port. It also ensures that the allocation can
only be refreshed this way by the same client. When a client's IP
address changes due to mobility, it presents the previously obtained
ticket in a Refresh Request to the TURN server. If the ticket is
found to be valid, the TURN server will retain the same relayed
address/port for the new IP address/port allowing the client to
continue using previous channel bindings -- thus, the TURN client
does not need to obtain new channel bindings. Any data from external
peer will be delivered by the TURN server to this new IP address/port
of the client. The TURN client will continue to send application
data to its peers using the previously allocated channelBind
Requests.
TURN TURN Peer
client server A
|-- Allocate request --------------->| |
| + MOBILITY-TICKET (length=0) | |
| | |
|<--------------- Allocate failure --| |
| (401 Unauthorized) | |
| | |
|-- Allocate request --------------->| |
| + MOBILITY-TICKET (length=0) | |
| | |
|<---------- Allocate success resp --| |
| + MOBILITY-TICKET | |
... ... ...
(changes IP address)
| | |
|-- Refresh request ---------------->| |
| + MOBILITY-TICKET | |
| | |
|<----------- Refresh success resp --| |
| + MOBILITY-TICKET | |
| | |
5.1. Creating an Allocation
Wing, et al. Expires March 31, 2014 [Page 9]
Internet-Draft MICE September 2013
5.1.1. Sending an Allocate Request
In addition to the process described in Section 6.1 of [RFC5766], the
client includes the MOBILITY-TICKET attribute with length 0. This
indicates the client is a mobile node and wants a ticket.
5.1.2. Receiving an Allocate Request
In addition to the process described in Section 6.2 of [RFC5766], the
server does the following:
If the MOBILITY-TICKET attribute is included, and has length zero,
and the TURN session mobility is forbidden by local policy, the
server MUST reject the request with the new Mobility Forbidden error
code. Following the rules specified in [RFC5389], if the server does
not understand the MOBILITY-TICKET attribute, it ignores the
attribute.
If the server can successfully process the request create an
allocation, the server replies with a success response that includes
a STUN MOBILITY-TICKET attribute. TURN server stores it's session
state, such as 5-tuple and NONCE, into a ticket that is encrypted by
a key known only to the TURN server and sends the ticket in the STUN
MOBILITY-TICKET attribute as part of Allocate success response.
The ticket is opaque to the client, so the structure is not subject
to interoperability concerns, and implementations may diverge from
this format. TURN Allocation state information is encrypted using
128-bit key for Advance Encryption Standard (AES) and 256-bit key for
HMAC-SHA-256 for integrity protection.
5.1.3. Receiving an Allocate Success Response
In addition to the process described in Section 6.3 of [RFC5766], the
client will store the MOBILITY-TICKET attribute, if present, from the
response. This attribute will be presented by the client to the
server during a subsequent Refresh request to aid mobility.
5.1.4. Receiving an Allocate Error Response
If the client receives an Allocate error response with error code TBD
(Mobility Forbidden), the error is processed as follows:
Wing, et al. Expires March 31, 2014 [Page 10]
Internet-Draft MICE September 2013
o TBD (Mobility Forbidden): The request is valid, but the server is
refusing to perform it, likely due to administrative restrictions.
The client considers the current transaction as having failed. The
client MAY notify the user or operator and SHOULD NOT retry the same
request with this server until it believes the problem has been
fixed.
All other error responses must be handled as described in [RFC5766].
5.2. Refreshing an Allocation
5.2.1. Sending a Refresh Request
If a client wants to refresh an existing allocation and update its
time-to-expiry or delete an existing allocation, it will send a
Refresh Request as described in Section 7.1 of [RFC5766]. If the
client wants to retain the existing allocation in case of IP change,
it will include the MOBILITY-TICKET attribute received in the
Allocate Success response. If a Refresh transaction was previously
made, the MOBILITY-TICKET attribute received in the Refresh Success
response of the transaction must be used.
5.2.2. Receiving a Refresh Request
In addition to the process described in Section 7.2 of [RFC5766], the
client does the following:
If the STUN MOBILITY-TICKET attribute is included in the Refresh
Request then the server will not retrieve the 5-tuple from the packet
to identify an associated allocation. Instead TURN server will
decrypt the received ticket, verify the ticket's validity and
retrieve the 5-tuple allocation from the contents of the ticket. If
this 5-tuple obtained from the ticket does not identify an existing
allocation then the server MUST reject the request with an error.
If the source IP address and port of the Refresh Request is different
from the stored 5-tuple allocation, the TURN server proceeds with
checks to see if NONCE in the Refresh request is the same as the one
provided in the ticket. The TURN server also uses MESSAGE-INTEGRITY
validation to identify the that it is the same user which had
previously created the TURN allocation. If the above checks are not
successful then server MUST reject the request with a 441 (Wrong
Credentials) error.
If all of the above checks pass, the TURN server understands that the
client has moved to a new network and acquired a new IP address. The
source IP address of the request could either be the host transport
address or server-reflexive transport address. The server then
Wing, et al. Expires March 31, 2014 [Page 11]
Internet-Draft MICE September 2013
updates it's 5-tuple with the new client IP address and port. TURN
server calculates the ticket with the new 5-tuple and sends the new
ticket in the STUN MOBILITY-TICKET attribute as part of Refresh
Success response.
5.2.3. Receiving a Refresh Response
In addition to the process described in Section 7.3 of [RFC5766], the
client will store the MOBILITY-TICKET attribute, if present, from the
response. This attribute will be presented by the client to the
server during a subsequent Refresh Request to aid mobility.
5.3. New STUN Attribute MOBILITY-TICKET
This attribute is used to retain an Allocation on the TURN server.
It is exchanged between the client and server to aid mobility. The
value is encrypted and identifies identifies session state such as
5-tuple and NONCE. The value of MOBILITY-TICKET is a variable-length
value.
5.4. New STUN Error Response Code
This document defines the following new error response code:
Mobility Forbidden: Mobility request was valid but cannot be
performed due to administrative or similar restrictions.
6. Comparison to ICE Restart and Trickle ICE
There has been some concern that ICE Mobility is unnecessary, and
that an ICE restart (section 9.1.1.1 of [RFC5245]) would provide
exactly the same functionality as ICE Mobility. These sections
examine how ICE restart and Trickle ICE
[I-D.rescorla-mmusic-ice-trickle] compare with ICE Mobility.
6.1. Break Before Make - ICE Restart
o If ICE Restart is used for RTP Mobility then in case of Break
before Make,
1. Before the endpoint can send an ICE restart message, it has to
first re-establish communication with its SIP proxy. This
consumes one round-trip for both TCP and UDP. If the
connection is protected with TLS (TCP) or DTLS (UDP), we can
assume TLS session resumption [RFC5077] will be used to reduce
the number of TLS messages. With TLS session resumption, this
consumes 1 round trip. If TLS session resumption is not
available, a full TLS handshake consumes 2 round trips. This
Wing, et al. Expires March 31, 2014 [Page 12]
Internet-Draft MICE September 2013
is a total of 2 round trips (with session resumption) to 3
round trips (without session resumption), which is multiplied
by the round trip time to the SIP proxy. The round trip time
is dependent on a particular network or deployment, for
example in second (2.5G), third (3G) generation wireless
networks and satellite communication round trip time could be
higher than 250ms. These calculations are only considering
the network round-trip time and do not consider the wall-clock
time to validate the TLS certificates or generate the TLS keys
on the TLS client or the TLS server, which would make this
longer.
2. While performing the above steps to re-establish SIP
connectivity with its SIP proxy, the endpoint will gather host
candidates which incur no network traffic, server-reflexive
candidates which incur a round-trip to a STUN server, and
relayed candidates which incurs three round trips (two for re-
authentication and one for creating the TURN permission). The
STUN and TURN communications can be performed in parallel with
the SIP connectivity check from step (1), above.
3. The endpoints through the SIP server will exchange offer/
answer. The SIP server could also be located halfway around
the world from the endpoints and the delay could be
significant. For SIP over UDP the endpoint will have send a
SIP request and wait for the response to arrive.
4. ICE restart requires sending a new INVITE. A new INVITE
cannot be sent if there is an open SIP dialog, such as a
previous INVITE. This means rapid mobility events will not
work well, and there is also an increased likelihood for glare
(both endpoints sending INVITEs at the same time).
6.2. Break Before Make - Trickle ICE
o If Trickle ICE [I-D.rescorla-mmusic-ice-trickle] is used for RTP
Mobility then in case of Break before Make,
1. Trickle ICE can begin connectivity checks while the endpoint
is still gathering candidates and can considerably shorten the
time necessary for ICE processing to complete. It still
involves the overhead of step 1 explained in section
Section 6.1.
2. The endpoint would learn host candidates and inform them to
the remote peer in offer, the remote peer will provide its
candidates in answer. The host, server reflexive, peer
reflexive and relayed candidates of the remote peer may not
Wing, et al. Expires March 31, 2014 [Page 13]
Internet-Draft MICE September 2013
change and the remote peer does not have to gather the
candidates again. Trickle ICE will test local host candidates
with all types of remote candidates provided by the remote
peer in the answer.
a. If the endpoint is not behind NAT and the ICE peer is
behind NAT performing endpoint dependent filtering (or
firewall blocking unsolicited incoming traffic) then ICE
connectivity checks initiated by the endpoint to the
remote peer will succeed as a consequence of suicide ICE
connectivitivy check packets.
b. If the endpoint is behind NAT and ICE peer is behind
endpoint-dependent filtering NAT then ICE connectivity
checks using the first offer/answer will fail but will
later succeed in subsequent offer/answer where the
endpoint provides server-reflexive candidates.
3. Trickle ICE must be supported by both endpoints for it be
used.
o If both endpoints support TRICKLE ICE then it is RECOMMENDED that
TRICKLE ICE be tried instead of ICE restart in steps (a) and (b)
of Section 3.1.
7. IANA Considerations
IANA is requested to add the following attributes to the STUN
attribute registry [iana-stun],
o MOBILITY-TICKET (0x802E, in the comprehension-optional range)
o MOBILITY-EVENT (0x802, in the comprehension-required range)
o MOBILITY-SUPPORT (0x8000, in the comprehension-optional range)
and to add a new STUN error code "Mobility Forbidden" with the value
501 to the STUN Error Codes registry [iana-stun].
8. Security Considerations
8.1. Considerations for ICE mechanism
A mobility event only occurs after both ICE endpoints have exchanged
their ICE information. Thus, both username fragments are already
known to both endpoints. Each endpoint contributes at least 24 bits
of randomness to the ice-ufrag (Section 15.4 of [RFC5245]), which
provides 48 bits of randomness. An off-path attacker would have to
Wing, et al. Expires March 31, 2014 [Page 14]
Internet-Draft MICE September 2013
guess those 48 bits to cause the endpoints to perform HMAC-SHA1
validation of the MESSAGE-INTEGRITY attribute.
An attacker on the path between the ICE endpoints will see both ice-
ufrags, and can cause the endpoints to perform HMAC-SHA1 validation
by sending messages from any IP address.
8.2. Considerations for TURN mechanism
TURN server MUST use strong encryption and integrity protection for
the ticket to prevent an attacker from using a brute force mechanism
to obtain the ticket's contents or refreshing allocations.
Security considerations described in [RFC5766] are also applicable to
this mechanism.
9. Acknowledgements
Thanks to Alfred Heggestad, Lishitao, Sujing Zhou, Martin Thomson,
Emil Ivov for review and comments.
10. Change History
[Note to RFC Editor: Please remove this section prior to
publication.]
10.1. Changes from draft-wing-mmusic-ice-mobility-00 to -01
o Updated section 3
10.2. Changes from draft-wing-mmusic-ice-mobility-01 to -02
o Updated Introduction, Notational Conventions, sections 3.1, 3.2.
o Updated section 3.5
10.3. Changes from draft-wing-mmusic-ice-mobility-02 to -03
o Moved sections Presence of other interfaces in Valid list, Losing
an Interface to Appendix.
10.4. Changes from draft-wing-mmusic-ice-mobility-03 to -04
o Added Section 6.
10.5. Changes from draft-wing-mmusic-ice-mobility-04 to -05
o Updated Section 6.
Wing, et al. Expires March 31, 2014 [Page 15]
Internet-Draft MICE September 2013
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC5245] Rosenberg, J., "Interactive Connectivity Establishment
(ICE): A Protocol for Network Address Translator (NAT)
Traversal for Offer/Answer Protocols", RFC 5245, April
2010.
[RFC5389] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing,
"Session Traversal Utilities for NAT (STUN)", RFC 5389,
October 2008.
[RFC5766] Mahy, R., Matthews, P., and J. Rosenberg, "Traversal Using
Relays around NAT (TURN): Relay Extensions to Session
Traversal Utilities for NAT (STUN)", RFC 5766, April 2010.
11.2. Informative References
[I-D.rescorla-mmusic-ice-trickle]
Rescorla, E., Uberti, J., and E. Ivov, "Trickle ICE:
Incremental Provisioning of Candidates for the Interactive
Connectivity Establishment (ICE) Protocol", draft-
rescorla-mmusic-ice-trickle-01 (work in progress), October
2012.
[RFC5077] Salowey, J., Zhou, H., Eronen, P., and H. Tschofenig,
"Transport Layer Security (TLS) Session Resumption without
Server-Side State", RFC 5077, January 2008.
[RFC5763] Fischl, J., Tschofenig, H., and E. Rescorla, "Framework
for Establishing a Secure Real-time Transport Protocol
(SRTP) Security Context Using Datagram Transport Layer
Security (DTLS)", RFC 5763, May 2010.
[RFC5780] MacDonald, D. and B. Lowekamp, "NAT Behavior Discovery
Using Session Traversal Utilities for NAT (STUN)", RFC
5780, May 2010.
[RFC6263] Marjou, X. and A. Sollaud, "Application Mechanism for
Keeping Alive the NAT Mappings Associated with RTP / RTP
Control Protocol (RTCP) Flows", RFC 6263, June 2011.
[iana-stun]
Wing, et al. Expires March 31, 2014 [Page 16]
Internet-Draft MICE September 2013
IANA, ., "IANA: STUN Attributes", April 2011,
<http://www.iana.org/assignments/stun-parameters/stun-pa
rameters.xml>.
Appendix A.
A.1. Presence of other interfaces in Valid list
This technique is optional and only relevant if there is a host
policy to maintain unused candidates on other interfaces using the
steps in Appendix A.2.1. ICE Agent can maintain unused candidates on
other interfaces if it detects that it is behind Address-Dependent
Filtering NAT or Firewall. ICE Agent can detect NAT, Firewall
behaviour using the procedure explained in [RFC5780]. When the
interface currently being used for media communication becomes
unavailable. If other interfaces are available and local candidates
from these interfaces are already present in the valid list then ICE
endpoint will perform the following steps:
1. The ICE endpoint based on the locally configured host policy
preferences, will select a interface whose candidates are already
present in the valid list.
2. The ICE endpoint clears all the pairs in the valid list
containing the IP addresses from the interface that become
unavailable.
3. The ICE endpoint initiates ICE connectivity checks on the
selected interface. The ICE endpoint acts as controlling agent
and MUST include MOBILITY-EVENT attribute to signal mobility
event and SHOULD also include the USE-CANDIDATE attribute to
signal an aggressive nomination (see Section 2.6 of [RFC5245]).
When all components have a nominated pair in the valid list,
media can begin to flow using the highest priority nominated
pair.
4. The ICE endpoint will re-establish connection with the SIP proxy.
Once ICE connectivity checks for all of the media streams are
completed, the controlling ICE endpoint follows the procedures in
Section 11.1 of [RFC5245], specifically to send updated offer if
the candidates in the m and c lines for the media stream (called
the DEFAULT CANDIDATES) do not match ICE's SELECTED CANDIDATES
(also see Appendix B.9 of [RFC5245]).
The ICE endpoint after Mobility using ICE is successful can issue an
updated offer indicating ICE restart if higher priority interface
becomes available.
Wing, et al. Expires March 31, 2014 [Page 17]
Internet-Draft MICE September 2013
A.1.1. Receiving ICE Mobility event
The ICE endpoint that receives ICE Mobility Event will perform the
steps in Section 3.1.1.
A.2. Losing an Interface
When an interface is lost, the SDP MAY be updated, so that the remote
ICE host does not waste its efforts with connectivity checks to that
address, as those checks will fail. Because it can be argued that
this is merely an optimization, and that the interface loss might be
temporary (and soon regained), and that ICE has reasonable
accommodation for candidates where connectivity checks timeout, this
specification does not strongly encourage updating the SDP to remove
a lost interface.
Likewise, this specification recommends that ICE candidate addresses
in valid list be maintained actively, subject to the host's policy.
For example, battery operated hosts have a strong incentive to not
maintain NAT binding for server reflexive candidates learnt through
STUN Binding Request, as the maintenance requires sending periodic
STUN Binding Indication. As another example, a host that is
receiving media over IPv6 may not want to persist with keeping a
NATted IPv4 mapping alive (because that consumes a NAT mapping that
could be more useful to a host actively utilizing the mapping for
real traffic).
Note: this differs from Section 8.3 of [RFC5245], which encourages
abandoning unused candidates.
A.2.1. Keeping unused candidates in the valid list active
ICE endpoint subject to host policy can continue performing ICE
connectivity checks using candidates from other interfaces on the
host even after ICE is complete. If valid list contains unused
candidate pairs from other interfaces and one of these interfaces can
be selected to send to media in case the existing interface used for
media is unavailable then ICE endpoint can keep the unused candidate
pairs from other interface{s} alive by sending keepalives every NN
seconds. It is recommended to only keep host/server-reflexive
candidates active in the valid list and not the relayed candidates.
A.2.1.1. Sending keep alive requests
Wing, et al. Expires March 31, 2014 [Page 18]
Internet-Draft MICE September 2013
Application Mechanism for Keeping Alive the NAT Mappings Associated
with RTP / RTP Control Protocol (RTCP) Flows [RFC6263] describes
various reasons for doing keepalives on inactive streams and how to
keep NAT mapping alive. However this specification requires some
additional functionality associated with the keepalives.
STUN binding requests MUST be used as the keepalive message instead
of the STUN Binding indication as specified in [RFC5245]. This is to
ensure positive peer consent from the remote side that the candidate
pair is still active and in future mobility can be achieved using the
steps in Appendix A.1 . The request must include the MOBILITY-SUPPORT
attribute. If the STUN binding response matches a pair in the
checklist then that candidate pair should be kept in the list. If
the STUN transaction fails then the candidate pair will be removed
from valid list.
A.2.1.2. Receiving keep alive requests
Upon receiving a STUN binding request containing a MOBILITY-SUPPORT
attribute even when ICE processing is in the Completed state, the ICE
endpoint will add this pair to the valid list if not already present
and generate STUN Binding Response containing the MOBILE-SUPPORT
attribute.
Authors' Addresses
Dan Wing
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134
USA
Email: dwing@cisco.com
Tirumaleswar Reddy
Cisco Systems, Inc.
Cessna Business Park, Varthur Hobli
Sarjapur Marathalli Outer Ring Road
Bangalore, Karnataka 560103
India
Email: tireddy@cisco.com
Wing, et al. Expires March 31, 2014 [Page 19]
Internet-Draft MICE September 2013
Prashanth Patil
Cisco Systems, Inc.
Cessna Business Park, Varthur Hobli
Sarjapur Marthalli Outer Ring Road
Bangalore, Karnataka 560103
India
Email: praspati@cisco.com
Paal-Erik Martinsen
Cisco Systems, Inc.
Philip Pedersens vei 22
Lysaker, Akershus 1325
Norway
Email: palmarti@cisco.com
Wing, et al. Expires March 31, 2014 [Page 20]