Network Working Group X. Xu
Internet-Draft Alibaba, Inc
Intended status: Standards Track S. Hegde
Expires: March 14, 2021 Juniper
D. Zhang
L. Xia
Huawei
September 10, 2020
Encapsulating IPsec ESP in UDP for Load-balancing
draft-xu-ipsecme-esp-in-udp-lb-05
Abstract
IPsec Virtual Private Network (VPN) is widely used by enterprises to
interconnect their geographical dispersed branch office locations
across the Wide Area Network (WAN) or the Internet, especially in the
Software-Defined-WAN (SD-WAN) era. In addition, IPsec is also
increasingly used by cloud providers to encrypt IP traffic traversing
data center interconnect WAN so as to meet the security and
compliance requirements, especially in financial cloud and
governmental cloud environments. To fully utilize the bandwidth
available in the WAN or the Internet, load balancing of IPsec traffic
over Equal Cost Multi-Path (ECMP) and/or Link Aggregation Group (LAG)
is much attractive to those enterprises and cloud providers. This
document defines a method to encapsulate IPsec Encapsulating Security
Payload (ESP) packets over UDP tunnels for improving load-balancing
of IPsec ESP traffic.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 14, 2021.
Xu, et al. Expires March 14, 2021 [Page 1]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Encapsulation in UDP . . . . . . . . . . . . . . . . . . . . 3
4. Processing Procedures . . . . . . . . . . . . . . . . . . . . 5
5. Congestion Considerations . . . . . . . . . . . . . . . . . . 6
6. Applicability Statements . . . . . . . . . . . . . . . . . . 6
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 6
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6
9. Security Considerations . . . . . . . . . . . . . . . . . . . 6
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 6
10.1. Normative References . . . . . . . . . . . . . . . . . . 6
10.2. Informative References . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 7
1. Introduction
IPsec Virtual Private Network (VPN) is widely used by enterprises to
interconnect their geographical dispersed branch office locations
across the Wide Area Network (WAN) or the Internet, especially in the
Software-Defined-WAN (SD-WAN) era. In addition, IPsec is also
increasingly used by cloud providers to encrypt IP traffic traversing
data center interconnect WAN so as to meet the security and
compliance requirements, especially in financial cloud and
governmental cloud environments. To fully utilize the bandwidth
available in the WAN or the Internet, load balancing of IPsec traffic
over Equal Cost Multi-Path (ECMP) and/or Link Aggregation Group (LAG)
is much attractive to those enterprises and cloud providers. Since
most existing core routers within IP WAN or the Internet can already
support balancing IP traffic flows based on the hash of the five-
tuple of UDP packets, by encapsulating IPsec Encapsulating Security
Xu, et al. Expires March 14, 2021 [Page 2]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
Payload (ESP) packets over UDP tunnels with the UDP source port being
used as an entropy field, it will enable existing core routers to
perform efficient load-balancing of the IPsec ESP traffic without
requiring any change to them. Therefore, this specification defines
a method of encapsulating IPsec ESP packets over UDP tunnels for
improving load-balancing of IPsec ESP traffic.
Encapsulating ESP in UDP, as defined in this document, can be used in
both IPv4 and IPv6 networks. IPv6 flow label has been proposed as an
entropy field for load balancing in IPv6 network environment
[RFC6438]. However, as stated in [RFC6936], the end-to-end use of
flow labels for load balancing is a long-term solution and therefore
the use of load balancing using the transport header fields would
continue until any widespread deployment is finally achieved. As
such, ESP-in-UDP encapsulation would still have a practical
application value in the IPv6 networks during this transition
timeframe.
Note that the difference between the ESP-in-UDP encapsulation as
proposed in this document and the ESP-in-UDP encapsulation as
described in [RFC3948] is that the former uses the UDP tunnel for
load-balancing improvement purpose and therefore the source port is
used as an entropy field while the latter uses the UDP tunnel for NAT
traverse purpose and therefore the source port is set to a constant
value (i.e., 4500). In addition, the ESP-in-UDP encapsulation as
described in this document is applicable to both the tunnel mode ESP
encapsulation and the transport mode ESP encapsulation.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Terminology
This memo makes use of the terms defined in [RFC2401]and [RFC2406].
3. Encapsulation in UDP
ESP-in-UDP encapsulation format is shown as follows:
Xu, et al. Expires March 14, 2021 [Page 3]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port = Entropy | Dest Port = TBD1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Length | UDP Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ ESP Packet ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: ESP-in-UDP Encapsulation Format
Source Port of UDP:
This field contains a 16-bit entropy value that is generated by
the encapsulator to uniquely identify a flow. What constitutes
a flow is locally determined by the encapsulator and therefore
is outside the scope of this document. What algorithm is
actually used by the encapsulator to generate an entropy value
is outside the scope of this document.
In case the tunnel does not need entropy, this field of all
packets belonging to a given flow SHOULD be set to a randomly
selected constant value so as to avoid packet reordering.
To ensure that the source port number is always in the range
49152 to 65535 (Note that those ports less than 49152 are
reserved by IANA to identify specific applications/protocols)
which may be required in some cases, instead of calculating a
16-bit hash, the encapsulator SHOULD calculate a 14-bit hash
and use those 14 bits as the least significant bits of the
source port field while the most significant two bits SHOULD be
set to binary 11. That still conveys 14 bits of entropy
information which would be enough as well in practice.
Destination Port of UDP:
This field is set to a value (TBD1) allocated by IANA to
indicate that the UDP tunnel payload is an ESP packet.
UDP Length:
Xu, et al. Expires March 14, 2021 [Page 4]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
The usage of this field is in accordance with the current UDP
specification [RFC0768].
UDP Checksum:
For IPv4 UDP encapsulation, this field is RECOMMENDED to be set
to zero for performance or implementation reasons because the
IPv4 header includes a checksum and use of the UDP checksum is
optional with IPv4. For IPv6 UDP encapsulation, the IPv6
header does not include a checksum, so this field MUST contain
a UDP checksum that MUST be used as specified in [RFC0768] and
[RFC2460] unless one of the exceptions that allows use of UDP
zero-checksum mode (as specified in [RFC6935]) applies.
ESP Packet:
This field contains one ESP packet.
4. Processing Procedures
This ESP-in-UDP encapsulation causes ESP [RFC2406] packets to be
forwarded across IP WAN via "UDP tunnels". When performing ESP-in-
UDP encapsulation by an IPsec VPN gateway, ordinary ESP encapsulation
procedure is performed and then a formatted UDP header is inserted
between ESP header and IP header. The Source Port field of the UDP
header is filled with an entropy value which is generated by the
IPsec VPN gateway. Upon receiving these UDP encapsulated packets,
remote IPsec VPN gateway MUST decapsulate these packets by removing
the UDP header and then perform ordinary ESP decapsulation procedure
consequently.
Similar to all other IP-based tunneling technologies, ESP-in-UDP
encapsulation introduces overheads and reduces the effective Maximum
Transmission Unit (MTU) size. ESP-in-UDP encapsulation may also
impact Time-to-Live (TTL) or Hop Count (HC) and Differentiated
Services (DSCP). Hence, ESP-in-UDP MUST follow the corresponding
procedures defined in [RFC2003].
Encapsulators MUST NOT fragment ESP packet, and when the outer IP
header is IPv4, encapsulators MUST set the DF bit in the outer IPv4
header. It is strongly RECOMMENDED that IP transit core be
configured to carry an MTU at least large enough to accommodate the
added encapsulation headers. Meanwhile, it is strongly RECOMMENDED
that Path MTU Discovery [RFC1191] [RFC1981] or Packetization Layer
Xu, et al. Expires March 14, 2021 [Page 5]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
Path MTU Discovery (PLPMTUD) [RFC4821] is used to prevent or minimize
fragmentation.
5. Congestion Considerations
TBD.
6. Applicability Statements
TBD.
7. Acknowledgements
8. IANA Considerations
One UDP destination port number indicating ESP needs to be allocated
by IANA:
Service Name: ESP-in-UDP Transport Protocol(s):UDP
Assignee: IESG <iesg@ietf.org>
Contact: IETF Chair <chair@ietf.org>.
Description: Encapsulate ESP packets in UDP tunnels.
Reference: This document.
Port Number: TBD1 -- To be assigned by IANA.
9. Security Considerations
TBD.
10. References
10.1. Normative References
[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
DOI 10.17487/RFC0768, August 1980,
<https://www.rfc-editor.org/info/rfc768>.
[RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
DOI 10.17487/RFC1191, November 1990,
<https://www.rfc-editor.org/info/rfc1191>.
[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery
for IP version 6", RFC 1981, DOI 10.17487/RFC1981, August
1996, <https://www.rfc-editor.org/info/rfc1981>.
[RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003,
DOI 10.17487/RFC2003, October 1996,
<https://www.rfc-editor.org/info/rfc2003>.
Xu, et al. Expires March 14, 2021 [Page 6]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2401] Kent, S. and R. Atkinson, "Security Architecture for the
Internet Protocol", RFC 2401, DOI 10.17487/RFC2401,
November 1998, <https://www.rfc-editor.org/info/rfc2401>.
[RFC2406] Kent, S. and R. Atkinson, "IP Encapsulating Security
Payload (ESP)", RFC 2406, DOI 10.17487/RFC2406, November
1998, <https://www.rfc-editor.org/info/rfc2406>.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
December 1998, <https://www.rfc-editor.org/info/rfc2460>.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, DOI 10.17487/RFC4821, March 2007,
<https://www.rfc-editor.org/info/rfc4821>.
[RFC6438] Carpenter, B. and S. Amante, "Using the IPv6 Flow Label
for Equal Cost Multipath Routing and Link Aggregation in
Tunnels", RFC 6438, DOI 10.17487/RFC6438, November 2011,
<https://www.rfc-editor.org/info/rfc6438>.
[RFC6935] Eubanks, M., Chimento, P., and M. Westerlund, "IPv6 and
UDP Checksums for Tunneled Packets", RFC 6935,
DOI 10.17487/RFC6935, April 2013,
<https://www.rfc-editor.org/info/rfc6935>.
[RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement
for the Use of IPv6 UDP Datagrams with Zero Checksums",
RFC 6936, DOI 10.17487/RFC6936, April 2013,
<https://www.rfc-editor.org/info/rfc6936>.
10.2. Informative References
[RFC3948] Huttunen, A., Swander, B., Volpe, V., DiBurro, L., and M.
Stenberg, "UDP Encapsulation of IPsec ESP Packets",
RFC 3948, DOI 10.17487/RFC3948, January 2005,
<https://www.rfc-editor.org/info/rfc3948>.
Authors' Addresses
Xu, et al. Expires March 14, 2021 [Page 7]
Internet-Draft Encapsulating ESP in UDP for Load-balancingSeptember 2020
Xiaohu Xu
Alibaba, Inc
Email: xiaohu.xxh@alibaba-inc.com
Shraddha Hegde
Juniper
Email: shraddha@juniper.net
Dacheng Zhang
Huawei
Email: dacheng.zhang@huawei.com
Liang Xia
Huawei
Email: frank.xialiang@huawei.com
Xu, et al. Expires March 14, 2021 [Page 8]