anima Y. Li
Internet-Draft L. Shen
Intended status: Standards Track Y. Zhou
Expires: May 19, 2022 Huawei Technologies
November 15, 2021
Autonomic IP Address To Access Control Group ID Mapping
draft-yizhou-anima-ip-to-access-control-groups-02
Abstract
This document defines the autonomic technical Objectives for IP
address/prefix to access control group IDs mapping information. The
Objectives defined can be used in Generic Autonomic Signaling
Protocol (GRASP) to make the policy enforcement point receive IP
address and its tied access control groups information directly from
the access authentication points and facilitate the group based
policy enforcement.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 19, 2022.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Li, et al. Expires May 19, 2022 [Page 1]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminologies . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Problems . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Autonomic IP Address to Access Control Groups ID Mapping
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1. Behaviours of IP to Group Mapping Information Providing
Nodes . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2. Behaviours of IP to Group Mapping Information Receiving
or Requesting Nodes . . . . . . . . . . . . . . . . . . . 8
5. Autonomic IP Address to Access Control Groups Objectives . . 10
5.1. IpToGroupId.AAP and IpToGroupId.PEP Objective Option . . 10
5.2. Example of Using the Defined Objective Options . . . . . 12
6. Security Considerations . . . . . . . . . . . . . . . . . . . 14
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 14
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 14
9.1. Normative References . . . . . . . . . . . . . . . . . . 14
9.2. Informative References . . . . . . . . . . . . . . . . . 15
Appendix A. Objective Examples . . . . . . . . . . . . . . . . . 16
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 16
1. Introduction
Ubiquitous group based policy management makes sure that the users
can obtain the same network access permission and QoS assurance
wherever they access the campus network. That is, the permission and
QoS assurance are tied to user role, rather than access points and/or
IP address assigned.
Group means a number of endpoints connecting to the network that
share common network policies. It facilitates the easy design and
provision of policy. A user's role is usually a group indicated by a
group ID. Group based policy management has been replacing the
traditional IP address and/or port number based policy widely.
The policy enforcement point (PEP) requires the IP address/prefix and
access control group ID mapping information of user in order to
execute the group based policy. This mapping information is usually
available at the access authentication point (AAP) during the
procedures of user access and authentication/authorization. However
PEP may not be the access authentication point. Therefore IP and
access control group ID mappings has to be passed to PEP.
Li, et al. Expires May 19, 2022 [Page 2]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
This document defines the autonomic technical Objectives for IP
address/prefix and access control group ID mapping. In this
document, group is also used for short to refer to the access control
group. The Generic Autonomic Signaling Protocol (GRASP) [RFC8990]
can make use of these technical Objectives as the basic building
blocks of a ubiquitous group based policy management solution,
especially for a campus network.
Autonomic Networking Infrastructure (ANI) is designed to provide the
elementary functions and services to be further integrated and used
by Autonomic Service Agents (ASA) on nodes. A campus policy
management system can integrate the function introduced in this
document when necessary. Such an Autonomic Service Agent (ASA)
performing the function of IP address/prefix to access control group
ID mapping is called IPAddressToAccessControlGroups ASA in this
document.
2. Terminologies
This document uses terminology defined in [RFC7575].
PEP: Policy Enforcement Point. A logical entity that enforces
policy decisions [RFC3198]. The policy decisions are group based
policies in this document.
AAP: Access Authentication Point. A logical entity that obtains the
information of the attaching clients' assigned IP address/prefix
and their access control group IDs. AAP may get the information
from one or different resources, for example, DHCP [RFC2131]
[RFC8415] server and/or RADIUS [RFC2865] server.
3. Problems
The traditional policy in a campus network is normally presented as
IP prefix/address based, for example, "Deny the traffic from IP
prefix X to IP prefix Y". Each of the access port of the switches is
assigned a subnet prefix and each subnet implies a group. It works
well when the end hosts are static. With the increasing deployment
of wireless accessed users and more complicated and dynamic
requirements of campus network policy, such an assumption no longer
holds. For instance, a user from the engineering department may
bring the laptop to access the campus network via a WiFi access
point. Then it will be assigned an IP address from a different
subnet prefix from the other fixed end hosts in the same engineering
department. It is hard and tedious to provision the consistent
policy with the other hosts in the same group for this specific IP
address. Another example is a user can belong to more than one
group, say group of department A and also VIP group. Group
Li, et al. Expires May 19, 2022 [Page 3]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
assignment is much more flexible than subnet defined IP address
assignment.
Therefore group based policy is used in such cases. No matter what
IP address is assigned to the user, its belonging access control
groups have no change and the group based policies have no change
either. For example, the policy can be "Allow the traffic from group
engineering whose group ID is 3 to group testing whose group ID is
15", or "assign the traffic destined to VIP group whose group ID is 1
the highest priority". In order to make group based policy work, the
IP address and its group mapping information has to be stored on PEP
so that IP addresses carried in data packet can be extracted and then
mapped to the group ID. For instance, when a packet with source
address X and destination address Y is received by PEP, PEP checks
its mapping table to get that source address X maps to group ID 3 and
destination address Y maps to group ID 15. It checks its policy
table to see what kind of policy, such as "allow" or "drop", should
be enforced on packet from group ID 3 to group ID 15. Then PEP
executes the group based policy. The mapping table is short for IP
address to access control group ID mapping table. For the
information in the mapping table, we call it IP and group mapping
information in this document.
IP and group mapping information is usually first available at the
access authentication point (AAP). AAP may serve as the DHCP relay
which remembers the IP address assigned to the client during DHCP
address assignment and at the same time it talks to AAA server to get
the client's group ID information based on client's identity using
AAA protocol such as RADIUS [RFC2865]. AAP then obtains the IP and
group mapping information. Figure 1 show a typical campus network.
The policy enforcement point (PEP) can be core switches, while the
access authentication point (AAP) is the access switch in the figure.
The problem to be solved by Autonomic Networking Infrastructure(ANI)
here is how to make IP address and access control group ID mapping
information passing from AAP to PEPs using
IPAddressToAccessControlGroups ASA.
Li, et al. Expires May 19, 2022 [Page 4]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
+-------+ +-------+
| core1 | --- | core2 | core switches (PEP)
+-------+ /+-------+
| \ / | \
| \ / | \
| \ / | \
| \ / | \
| \ | \
+-------+ / \ +-------+ +-------+
| acc1 |/ \| acc2 | | acc3 | access switches
+-------+ +-------+ +-------+ (AAP)
|
|
|
|
+-------+
| WiFi |
| AP1 | wifi access point
+-------+
Figure 1: Hierarchical Campus Network
A more complex campus network is shown in Figure 2. There are 4 PEPs
are deployed at the key positions for different types of traffic.
The AAPs obtaining a user's IP and group ID mapping information are
access switches which are the access nodes for the attaching clients.
Li, et al. Expires May 19, 2022 [Page 5]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
via VPN tunnel -----
+--------+ / \
| user2 |-----------+Internet |
|(group1)| | |
+--------+ \-------/
|
|
|
+---------------------|--------+
----- | | |
/ \ | +--------+ +--------+ |
| WAN | --------------| WAN | | VPN | |
| | | | border | |Internet| |
\-------/ | |firewall| |gateway | |
| | +--------+ +--------+ |
| | |PEP3 | PEP2 |
| | | +----+ |
+------|---------+ | | | |
| | | | +--------+ | +--------+ |
| +--------+ | | | core |---+ | | |
| | core | | | | switch |-----|firewall| |
| | switch | | | +--------+ +--------+ |
| +--------+ | | | PEP1 |
| |PEP4 | | | |
| | | | | |
| | | | +--------+ +--------+ |
| +--------+ | | | switch | --- | switch | |
| | switch | | | +--------+ +--------+ |
| +--------+ | | | AAP2 | AAP1 |
| | AAP3 | | | | |
| | | | +--------+ +--------+ |
| +--------+ | | | user1 | | user3 | |
| | user4 | | | |(group1)| |(group2)| |
| |(group2)| | | +--------+ +--------+ |
| +--------+ | | |
| | | |
| | | |
|Branch | | Headquarter |
+----------------+ +------------------------------+
Figure 2: Campus Networks with remote access
Some deployment uses a centralized controller to distribute IP and
group ID mapping information. Every single AAP reports its IP and
group ID mapping information to the controller. Controller pushes
the information regularly to all the PEPs. In addition, when a PEP
receives a data packet without pre-stored mapped group ID information
Li, et al. Expires May 19, 2022 [Page 6]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
of the corresponding IP addresses, it queries the controller for the
group IDs of the source and/or destination IP addresses and then
enforce the group based policy. This approach requires an explicit
controller able to talk to each and every AAP and PEP. In the
deployment where the headquarter and branch campus networks are far
apart, it will require controllers for each site to exchange
information or have another super-controller to help exchange the
information among sites. It introduces the complexity and
interoperability issues.
Autonomic Networking (AN) puts the intelligence at the node level, to
minimize dependency on human administrators and central management
such as a controller. The Autonomic Networking approach discussed in
this document is based on the assumption that there is a generic
discovery and negotiation protocol that enables direct negotiation
and/or synchronization between the routers or switches. GRASP
[RFC8990] is intended to be such a protocol which can make use of the
technical Objectives defined in the following sections as the basic
building blocks of a ubiquitous group based policy management
solution, especially for a campus network. The ultimate goal is
self-management of campus networks which can expand over multiple
sites and share the same set of policies, including self-
configuration, self-optimization, self-healing and self-protection
(sometimes collectively called self-X).
4. Autonomic IP Address to Access Control Groups ID Mapping Procedures
IPAddressToAccessControlGroups ASA carries out the the function of IP
address/prefix to access control groups ID mapping in this document.
The procedures is illustrated below. As noted in Section 3, a
network node with IPAddressToAccessControlGroups ASA deployed usually
has a role of either AAP or PEP. Therefore two new GRASP Objectives
are defined and used for Objective name based multiplexing. They are
IpToGroupId.PEP and IpToGroupId.AAP respectively. Section 5 gives
more details of the format of them.
The basic procedures are AAP provides the mapping information to PEPs
whenever it obtains new or updated or withdrawn mapping information.
PEPs will then store the information for future policy enforcement
usage. A rare case is that a PEP requests the group ID for a
specific IP address when it finds that information is required but
not locally stored. AAP possessing such mapping information will
reply to this request.
Li, et al. Expires May 19, 2022 [Page 7]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
4.1. Behaviours of IP to Group Mapping Information Providing Nodes
IPAddressToAccessControlGroups ASA with mapping information providing
feature is usually an AAP supporting IpToGroupId.AAP Objective
option. If a PEP would like to provide mapping information as well
to the other PEPs, it is logically an AAP in that procedure. Then
such PEPs should support both IpToGroupId.PEP and IpToGroupId.AAP
Objective options in its IPAddressToAccessControlGroups ASA.
AAP obtains the mapping of IP address and group IDs of a user in
various ways. For instance, use RADIUS [RFC2865] or CAPWAP [RFC5415]
to get the user's access control group IDs during authentication
phase and use DHCP snooping to get the user's assigned IP address.
Therefore the IP and group ID mapping information of a user can be
obtained by AAP at the very early stage when the user connects to the
network. Sometimes such mapping information can be statically
provisioned based on port or VLAN. Mapping information obtained in
such ways is stored locally on AAP. AAP discovers the
IPAddressToAccessControlGroups ASA supporting IpToGroupId.PEP first.
Then AAP sends Request Negotiation message to those PEPs with the
mapping information it has. Whenever there is a change or withdrawn
of the mapping information, AAP has to send Request Negotiation again
to PEPs for updating.
The providing nodes of mapping information are usually at the network
edges. The requesting or receiving nodes of the mapping information
are normally aggregation or core nodes with more storage and
capability to enforce the policy. There are normally only a few of
them, for instance two in a campus network. Therefore the number of
mapping information receiving nodes is usually much less than the
number of providing nodes. Hence it is quite efficient that the
information providing AAP nodes proactively send the mapping
information to the receiving PEP nodes. It is the most common case
how the mapping information is distributed.
In some rare cases that an AAP receives the Request Synchronization
with specific IP address and NULL (represented by zero) group ID, it
should reply with Synchronization message with the mapped group ID of
the specific IP address. If an AAP has no such mapped information
available locally, it can reply with an Invalid message.
4.2. Behaviours of IP to Group Mapping Information Receiving or
Requesting Nodes
IPAddressToAccessControlGroups ASA with mapping information
requesting or receiving feature is usually a PEP supporting
IpToGroupId.PEP Objective option. PEPs need to map the IP address/
Li, et al. Expires May 19, 2022 [Page 8]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
prefix of the received data packets to one or more group IDs in order
to enforce the group based policy.
PEPs deployed IPAddressToAccessControlGroups ASA supporting
IpToGroupId.PEP Objective option will receive the Request Negotiation
GRASP message with the mapping information from the information
providing AAP nodes as shown in Section 4.1. It should save the
mapping information locally. And reply with an Negotiation End GRASP
message with an Accept option.
It makes the mapping information of the specific IP addresses
received and pre-stored in most cases by PEP before the data packet
with those addresses as source or destination is received.
However there are cases that the mapped group ID information of the
IP address is not pre-stored when a data packet with that IP address
arrives, for example due to timeout or unintentional withdrawn of the
mapping information. Then PEPs will send the Request Synchronization
with the specific IP address and NULL group ID to ask AAPs for the
mapping information.
The request can be triggered by the first data packet of a flow.
Group based policy requires both the source and destination group IDs
which are mapped from source and destination IP addresses
respectively. If any of such mapping is not locally available, the
requesting node needs to ask for it. In some implementation, data
packet encapsulation includes the source group ID directly such as in
the reserved field in VXLAN [RFC7348]. Therefore it is up to the
requesting node to determine if both source and destination group IDs
or only one of them should be requested. If the requesting node is a
tunnel endpoint, usually the inner rather than outer IP addresses
should be used to request for the corresponding group id.
The request can also be sent periodically or voluntarily. It can be
sent when a newly booted requesting node wants to get the whole set
of mapping information or when a requesting node would like have an
explicit refreshment on some specific information.
The requesting PEP should send out a GRASP Discovery message
containing IpToGroupId.AAP Objective option in order to discover
AAPs. It then acts as a GRASP synchronization initiator by sending
the Request Synchronization with IP address and NULL group ID as the
Objective values to ask for the mapping information. This starts a
GRASP synchronization process.
Li, et al. Expires May 19, 2022 [Page 9]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
5. Autonomic IP Address to Access Control Groups Objectives
This section defines two GRASP technical Objective options
IpToGroupId.AAP and IpToGroupId.PEP that can be used by
IPAddressToAccessControlGroups ASA to support autonomic IP address/
prefix to access control group ID mapping information distribution.
5.1. IpToGroupId.AAP and IpToGroupId.PEP Objective Option
Both IpToGroupId.AAP and IpToGroupId.PEP Objective option are GRASP
Objective options conforming to [RFC8990]. They share the same
Objective option value format defined in this section. Normally
IpToGroupId.AAP Objective option should be supported by
IPAddressToAccessControlGroups ASA deployed on AAP nodes to provide
the mapping information and IpToGroupId.PEP Objective option should
be supported by IPAddressToAccessControlGroups ASA deployed on PEP
nodes to request or receive the mapping information .
The Objective carries the IP prefix/address and its mapping access
control group IDs. The format of them in CBOR (Concise Binary Object
Representation [RFC8949]) is show in Concise data definition language
(CDDL) [RFC8610] as follows. Tags for general IPv4 and IPv6
addresses and prefixes defined in [I-D.ietf-cbor-network-addresses]
are used.
Li, et al. Expires May 19, 2022 [Page 10]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
objective = ["IpToGroupId.AAP",
objective-flags, loop-count,
[ip-address-or-prefix, *group-id]]
objective = ["IpToGroupId.PEP",
objective-flags, loop-count,
[ip-address-or-prefix, *group-id]]
group-id = uint
; copied from draft-ietf-cbor-network-addresses, RFC YYYY TBD:
ip-address-or-prefix = ipv6-address-or-prefix/ipv4-address-or-prefix
ipv6-address-or-prefix = #6.54(ipv6-address / ipv6-prefix)
ipv4-address-or-prefix = #6.52(ipv4-address / ipv4-prefix)
ipv6-prefix = [ipv6-prefix-length, ipv6-prefix-bytes]
ipv4-prefix = [ipv4-prefix-length, ipv4-prefix-bytes]
ipv6-prefix-length = 0..128
ipv4-prefix-length = 0..32
ipv6-prefix-bytes = bytes .size (uint .le 16)
ipv4-prefix-bytes = bytes .size (uint .le 4)
ipv6-address = bytes .size 16
ipv4-address = bytes .size 4
; copied from the GRASP specification, RFC 8990:
objective-flags = uint .bits objective-flag
objective-flag = &(
F_DISC: 0 ; valid for discovery
F_NEG: 1 ; valid for negotiation
F_SYNCH: 2 ; valid for synchronization
F_NEG_DRY: 3 ; negotiation is a dry run
)
loop-count = 0..255
A common practice usually uses 16 bits to present a group ID. But
the representation does not limit that. Zero group ID represents a
NULL group value and is used for full retraction of a prefix or
address.
Li, et al. Expires May 19, 2022 [Page 11]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
5.2. Example of Using the Defined Objective Options
Figure 1 shows a typical campus network of with three access switches
which are AAPs and two core switches which are PEPs. We assume that
the policy in this campus is outsource_group (which has group ID 5)
is not allowed to access accounting_group (which has group ID 10).
The policy (5, 10, drop) expressed in the form of (source group ID,
destination group ID, action) is provisioned on the PEPs which are
core switches in the figure.
When a user gets connected, the access switch which is an AAP snoops
the DHCP address assignment exchange to obtain the IP address IP_A.
The user provides a user ID to get authenticated via 802.1x and
RADIUS protocol. Thus the access switch obtains the user's group ID
which is 5 in this example in authentication procedures. So the
access switch has the mapping information (IP_A, 5) in the form of
(IP address, access control group ID). The mapping information is
then passed from the access switch to the core switches which are
PEPs using GRASP Objective defined in this document. Figure 3 shows
an example of the procedures. Only the key values of the Objective
is shown for simplicity.
Li, et al. Expires May 19, 2022 [Page 12]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
+-------------+ +-------------+ +-------------+
|access switch| | core switch | | core switch |
| (AAP) | | (PEP1) | | (PEP2) |
+-------------+ +-------------+ +-------------+
|
| |
| | |
| Discovery (IpToGroupId.PEP) |
| | |
|------------------------>-------------------->|
| | |
| Discovery Response | |
|<----------------------- | |
| Discovery Response |
|<---------------------------------------------|
| | |
| | |
| | |
|Request Negotiation ( | |
|IpToGroupId.PEP,(IP_A,5))| |
|------------------------>| save (IP_A,5) |
| | |
| Negotiation End (ACCEPT)| |
|<----------------------- | |
| | |
| Request Negotiation ( |
| IpToGroupId.PEP,(IP_A,5)) |
|--------------------------------------------->|save (IP_A,5)
| | |
| | |
| | |
| Negotiation End (ACCEPT) |
|<---------------------------------------------|
| | |
| | |
| | |
Figure 3: Example of AAP pushing mapping information to PEPs
After the core switches get this mapping information, they save it
for future policy enforcement. For example, when a data packet with
source IP address IP_A and destination IP address IP_B is received,
the PEP checks its mapping table to get the group ID 5 for IP_A and
group ID 10 for IP_B. Then the policy provisioned as (5, 10, drop)
is enforcement. So the data packet will be dropped. It facilitates
the group based policy execution.
Li, et al. Expires May 19, 2022 [Page 13]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
6. Security Considerations
Security consideration for GRASP [RFC8990] applies in this document.
The preferred security model is that devices are trusted following
the secure bootstrap procedure [RFC8995] and that a secure Autonomic
Control Plane (ACP) [RFC8994] is in place.
7. IANA Considerations
This document defines two new GRASP Objective option names:
"IpToGroupId.AAP" and "IpToGroupId.PEP". The IANA is requested to
added them to the "GRASP Objective Names" subregistry defined by
[RFC8990].
8. Acknowledgements
Thanks to Carsten Bormann, Brian Carpenter and Michael Richardson for
useful suggestions and revising CDDL representations.
9. References
9.1. Normative References
[RFC7575] Behringer, M., Pritikin, M., Bjarnason, S., Clemm, A.,
Carpenter, B., Jiang, S., and L. Ciavaglia, "Autonomic
Networking: Definitions and Design Goals", RFC 7575,
DOI 10.17487/RFC7575, June 2015,
<https://www.rfc-editor.org/info/rfc7575>.
[RFC8610] Birkholz, H., Vigano, C., and C. Bormann, "Concise Data
Definition Language (CDDL): A Notational Convention to
Express Concise Binary Object Representation (CBOR) and
JSON Data Structures", RFC 8610, DOI 10.17487/RFC8610,
June 2019, <https://www.rfc-editor.org/info/rfc8610>.
[RFC8990] Bormann, C., Carpenter, B., Ed., and B. Liu, Ed., "GeneRic
Autonomic Signaling Protocol (GRASP)", RFC 8990,
DOI 10.17487/RFC8990, May 2021,
<https://www.rfc-editor.org/info/rfc8990>.
[I-D.ietf-cbor-network-addresses]
Richardson, M. and C. Bormann, "CBOR tags for IPv4 and
IPv6 addresses and prefixes", draft-ietf-cbor-network-
addresses-13 (work in progress), October 2021.
Li, et al. Expires May 19, 2022 [Page 14]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
9.2. Informative References
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol",
RFC 2131, DOI 10.17487/RFC2131, March 1997,
<https://www.rfc-editor.org/info/rfc2131>.
[RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
"Remote Authentication Dial In User Service (RADIUS)",
RFC 2865, DOI 10.17487/RFC2865, June 2000,
<https://www.rfc-editor.org/info/rfc2865>.
[RFC3198] Westerinen, A., Schnizlein, J., Strassner, J., Scherling,
M., Quinn, B., Herzog, S., Huynh, A., Carlson, M., Perry,
J., and S. Waldbusser, "Terminology for Policy-Based
Management", RFC 3198, DOI 10.17487/RFC3198, November
2001, <https://www.rfc-editor.org/info/rfc3198>.
[RFC5415] Calhoun, P., Ed., Montemurro, M., Ed., and D. Stanley,
Ed., "Control And Provisioning of Wireless Access Points
(CAPWAP) Protocol Specification", RFC 5415,
DOI 10.17487/RFC5415, March 2009,
<https://www.rfc-editor.org/info/rfc5415>.
[RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
eXtensible Local Area Network (VXLAN): A Framework for
Overlaying Virtualized Layer 2 Networks over Layer 3
Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
<https://www.rfc-editor.org/info/rfc7348>.
[RFC8415] Mrugalski, T., Siodelski, M., Volz, B., Yourtchenko, A.,
Richardson, M., Jiang, S., Lemon, T., and T. Winters,
"Dynamic Host Configuration Protocol for IPv6 (DHCPv6)",
RFC 8415, DOI 10.17487/RFC8415, November 2018,
<https://www.rfc-editor.org/info/rfc8415>.
[RFC8949] Bormann, C. and P. Hoffman, "Concise Binary Object
Representation (CBOR)", STD 94, RFC 8949,
DOI 10.17487/RFC8949, December 2020,
<https://www.rfc-editor.org/info/rfc8949>.
[RFC8994] Eckert, T., Ed., Behringer, M., Ed., and S. Bjarnason, "An
Autonomic Control Plane (ACP)", RFC 8994,
DOI 10.17487/RFC8994, May 2021,
<https://www.rfc-editor.org/info/rfc8994>.
Li, et al. Expires May 19, 2022 [Page 15]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
[RFC8995] Pritikin, M., Richardson, M., Eckert, T., Behringer, M.,
and K. Watsen, "Bootstrapping Remote Secure Key
Infrastructure (BRSKI)", RFC 8995, DOI 10.17487/RFC8995,
May 2021, <https://www.rfc-editor.org/info/rfc8995>.
Appendix A. Objective Examples
This appendix shows a number of examples of Objective defined in this
document conforming to the CDDL syntax given in Section 5.1.
["IpToGroupId.PEP", 15, 101,
[54([4, h'A50386A78BA56FA4BBC734281C51']), 3506, 2698, 4562]]
["IpToGroupId.PEP", 5, 73, [52(h'9946B8A3'), 2881,
2265, 1720, 2450]]
["IpToGroupId.PEP", 15, 161,
[54(h'39F3045B641AD291B057CD1857A7314A')]]
["IpToGroupId.PEP", 15, 2, [52(h'98A1CE4F')]]
["IpToGroupId.PEP", 15, 66, [52(h'69A16BFE'), 2601,
1851, 3876, 1405]]
["IpToGroupId.AAP", 15, 254,
[54(h'38AB303B8895DC95068CE00248D2FE91'), 4019, 1166, 3113]]
["IpToGroupId.AAP", 15, 63, [52([4, h'0B48']), 3035,
1181]]
["IpToGroupId.AAP", 15, 44, [52(h'01F1D8FF'), 3099,
1577, 1138, 1670]]
["IpToGroupId.AAP", 15, 181,
[54(h'2C74719F9355BA4E3BDE5689D1FE4CB0')]]
["IpToGroupId.PEP", 15, 129, [52(h'A2EF97C7'), 3149,
2728]]
Authors' Addresses
Yizhou Li
Huawei Technologies
Email: liyizhou@huawei.com
Li, et al. Expires May 19, 2022 [Page 16]
Internet-Draft Auto IP and Access Group ID Mapping November 2021
Li Shen
Huawei Technologies
Email: kevin.shenli@huawei.com
Yujing Zhou
Huawei Technologies
Email: zhouyujing3@huawei.com
Li, et al. Expires May 19, 2022 [Page 17]