Network Working Group                                         R. Bergman
Request for Comments: 2708                            Dataproducts Corp.
Category: Informational                                    November 1999


            Job Submission Protocol Mapping Recommendations
                       for the Job Monitoring MIB

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

Abstract

   This document defines the recommended mapping for many currently
   popular Job submission protocols to objects and attributes in the Job
   Monitoring MIB.

Table of Contents

   1.0  INTRODUCTION.................................................2
   2.0  LINE PRINTER DAEMON (LPR/LPD) PROTOCOL.......................4
   2.1  jmJobSubmissionID Mapped to LPR/LPD..........................4
   2.2  jmJobIndex Mapped to LPR/LPD.................................5
   2.3  Other MIB Objects Mapped to LPR/LPD..........................5
   2.4  The Attribute Group Mapped to LPD............................5
   3.0  APPLETALK PROTOCOL...........................................6
   3.1  jmJobSubmissionID Mapped to AppleTalk........................6
   3.2  Other AppleTalk Mappings.....................................6
   4.0  INTERNET PRINTING PROTOCOL (IPP).............................6
   4.1  jmJobSubmissionID Mapped to IPP..............................7
   4.2  jmJobIndex Mapped to IPP.....................................7
   4.3  Other MIB Objects Mapped to IPP..............................8
   4.4  The Attribute Group Mapped to IPP............................8
   5.0  INTELLIGENT PRINTER DATA STREAM (IPDS)......................10
   5.1  jmJobSubmissionId Mapped to IPDS............................10
   5.2  The Attribute Group Mapped to IPDS..........................11
   6.0  DOCUMENT PRINTING APPLICATION (DPA).........................11
   6.1  jmJobSubmissionID Mapped to DPA.............................11
   6.2  jmJobIndex Mapped to DPA....................................12
   6.3  Other MIB Objects Mapped to DPA.............................12
   6.4  The Attribute Group Mapped to DPA...........................13



Bergman                      Informational                      [Page 1]


RFC 2708            Job Submission Protocol Mapping        November 1999


   7.0  NOVELL DISTRIBUTED PRINT SERVICE (NDPS).....................14
   7.1  jmJobSubmissionID Mapped to NDPS............................14
   7.2  jmJobIndex Mapped to NDPS...................................14
   7.3  Other MIB Objects Mapped to NDPS............................15
   7.4  The Attribute Group Mapped to NDPS..........................15
   8.0  PRINTER JOB LANGUAGE (PJL)..................................17
   8.1  jmJobSubmissionID Mapped to PJL.............................17
   8.2  jmJobIndex Mapped to PJL....................................18
   8.3  Other MIB Objects Mapped to PJL.............................18
   8.4  The Attribute Group Mapped to PJL...........................18
   9.0  POSTSCRIPT..................................................18
   9.1  jmJobSubmissionID Mapped to PostScript......................19
   9.2  Other MIB Objects and Attributes Mapped to PostScript.......19
   10.0  NETWARE PSERVER............................................19
   10.1  jmJobSubmissionID Mapped to PServer........................19
   10.2  jmJobIndex Mapped to PServer...............................19
   10.3  Other MIB Objects Mapped to PJL............................20
   10.4  The Attribute Group Mapped to PServer......................20
   11.0  NETWARE NPRINTER or RPRINTER...............................20
   12.0  SERVER MESSAGE BLOCK (SMB) PROTOCOL........................21
   12.1  jmJobSubmissionID Mapped to SMB............................21
   12.2  jmJobIndex Mapped to SMB...................................21
   12.3  Other MIB objects Mapped to SMB............................21
   13.0  TRANSPORT INDEPENDENT PRINTER/SYSTEM INTERFACE (TIP/SI)....22
   13.1  jmJobSubmissionID Mapped to TIP/SI.........................22
   13.2  jmJobIndex Mapped to TIP/SI................................22
   13.3  Other MIB Objects Mapped to TIP/SI.........................22
   13.4  The Attribute Group Mapped to TIP/SI.......................22
   14.0  SECURITY CONSIDERATIONS....................................23
   15.0  REFERENCES.................................................23
   16.0  AUTHORS' ADDRESSES.........................................24
   17.0  FULL COPYRIGHT STATEMENT...................................26

1.0  INTRODUCTION

   The Job Monitoring MIB [JobMIB] is intended to be implemented in a
   device or server that supports any job submission protocol.  However,
   the information available and the method of presentation varies
   significantly by job submission protocol.  A common method of mapping
   job submission information to the Job Monitoring MIB is essential for
   interoperability of Job MIB agents and monitoring applications.  This
   document defines recommended mappings for most popular job submission
   protocols to ensure this compatibility.








Bergman                      Informational                      [Page 2]


RFC 2708            Job Submission Protocol Mapping        November 1999


   All mappings are unidirectional from the job submission protocol to
   the MIB.  It is assumed that support of the job submission protocol
   in the printer implies that the reverse information flow is presently
   defined and does not require interaction from the MIB.  This mapping
   is not defined in this document as it should be obvious.

   This document refers to system configurations that are defined in the
   Job Monitoring MIB [JobMIB].  For those readers that are familiar
   with the configuration descriptions, a short summary appears here.
   Please see the Job MIB document for further details.

   Configuration 1:  This is a simple peer-to-peer system which contains
                     only a client and a printer.  The Job MIB agent is
                     resident in the printer.

   Configuration 2:  This system contains a client, server, and a
                     printer.  The Jib MIB agent is resident in the
                     server.

   Configuration 3:  This system, as in configuration 2, contains a
                     client, server, and a printer.  In this case the
                     Job MIB agent is implemented within the printer.

   The most important object to be mapped is jmJobSubmissionID, since
   this is a method for the user or client to determine the jmJobIndex
   for a submitted job.  Therefore, jmJobSubmissionID is specified for
   all job submission protocols defined in this document.  The remaining
   objects mapped include only those items that have the equivalent
   information presented to the printer by the job submission protocol.

   While this document places a strong emphasis on jmJobSubmissionID
   mapping to obtain jmJobIndex, the preferred method is through the use
   of a bi-directional job submission protocol that returns the
   equivalent value of jmJobIndex to the client, such as IPP.  When a
   bi-directional protocol that returns jmJobIndex is in use, the
   jmJobSubmissionID object has no value to the client.  When the
   jmJobIndex cannot be returned, the use of a client defined
   jmJobSubmissionID is preferred over an agent derived value.  The
   client defined version allows for retrieval of jmJobIndex using a
   single SNMP Get operation, since jmJobSubmissionID is the index into
   the jmJobIDTable.  An agent derived value will require a search
   through multiple entries in the jmJobIDTable.

   The majority of the protocols mapped in this document are oriented
   towards network job submission.  However, the Job Monitoring MIB is
   also intended to monitor print jobs received from other than network
   ports, such as parallel and serial ports.  Some of the job submission
   protocols included that are used with non-networked ports are PJL,



Bergman                      Informational                      [Page 3]


RFC 2708            Job Submission Protocol Mapping        November 1999


   PostScript, and TIP/SI.  In addition, the Job Monitoring MIB can be
   used with print jobs that are internally generated, such as self test
   pages.  In this latter case, no mapping is required since all job
   submission protocols are bypassed.

2.0  LINE PRINTER DAEMON (LPR/LPD) PROTOCOL

   The LPR/LPD printing protocol [LPD] is used with BSD UNIX systems in
   the client-server-printer configuration.  Usage of the Job Monitoring
   MIB with LPR/LPD will most likely conform to Configuration 3, where
   the monitor application or the server uses SNMP to obtain job
   information from the printer.  The client communicates with the UNIX
   server using the existing LPD protocol to obtain job information.

   The LPR/LPD protocol is also used in the Windows environment to
   implement peer-to-peer printing, as shown in configuration 1.  In
   this case, SNMP is used by the client and/or the monitor application
   to obtain the job information.

   One of the major problems of LPR/LPD is the large number of vendor
   unique extensions currently used with the protocol and the resulting
   compatibility issues between available implementations.  To avoid
   these issues, this mapping of LPR/LPD is restricted to the protocol
   as defined by RFC 1179.

   The LPR/LPD protocol transfers print job data and control information
   in separate files, known as the Data File and Control File,
   respectively.  Most of the information concerning the print job is
   contained in the Control File.  In many LPD implementations, the
   Control File is transferred following the Data File.  Thus much of
   the information concerning the job may not be available until the
   completion of the data transmission.

2.1  jmJobSubmissionID Mapped to LPR/LPD

   The LPR/LPD Receive Data File command contains a parameter which
   defines the name of the data file.  This name field is structured as
   follows:

      dfaXXX<host-name>  or  daXXXX<host-name>

   Where XXX or XXXX is the numeric job number assigned by the network
   entity submitting the print job to the printer.  The recommended
   mapping of this name field to jmJobSubmissionID is:







Bergman                      Informational                      [Page 4]


RFC 2708            Job Submission Protocol Mapping        November 1999


   octet 1:   '9'

   octets 2-40:  Contains the <host-name> portion of the name field.  If
                 the <host-name> portion is less than 40 octets, the
                 left-most character in the string shall appear in octet
                 position 2.  Any unused portion of this field shall be
                 filled with spaces.  Otherwise, only the last 39 bytes
                 shall be included.

   octets 41-48:  '00000XXX' or '0000XXXX', where XXX or XXXX is the
               decimal (ASCII coded) representation of the LPR/LPD job
               number.

2.2  jmJobIndex Mapped to LPR/LPD

   The job index (jmJobIndex) is assigned by the SNMP job monitoring
   agent and is independent of the XXX (or XXXX) index assigned by the
   LPR/LPD client.  This will allow the SNMP agent to track jobs
   received from multiple sources.

2.3  Other MIB Objects Mapped to LPR/LPD

MIB Object                    | LPR/LPD Parameter
------------------------------+----------------------------------------
jmJobKOctetsPerCopyRequested  | Number of bytes as defined in the Data
                              |  File
jmJobOwner                    | Control file command code = P (User Id)

2.4  The Attribute Group Mapped to LPD

   Other attributes that are applicable, but not defined in this section
   such as attributes that map to a vendor unique extension, may also be
   included.

MIB attribute         | LPR/LPD information             | Data type
----------------------+---------------------------------+--------------
jobName               | Job Name (notes 1, 2)           | Octet String
queueNameRequested    | Queue name from the Data File   | Octet String
fileName              | Source File Name (notes 1, 3)   | Octet String

Notes:
------
   1. The information is optional in the Control File.  The attribute
      should be included if present in the Control File.
   2. Control file command code = J.  If this optional field is omitted
      from the control file, then the agent returns the file name
      (command code = N), if present.
   3. Control file command code = N.



Bergman                      Informational                      [Page 5]


RFC 2708            Job Submission Protocol Mapping        November 1999


3.0  APPLETALK PROTOCOL

   AppleTalk was originally developed as a peer-to-peer network
   protocol, as described in configuration 1, for use with Apple
   Macintosh computers.  Today, print spoolers are also available for
   use with Macintosh computer networks that conform to configurations
   2/3.  In addition, printing with the AppleTalk protocol is supported
   from both Windows NT servers and Novell servers also per
   configurations 2/3.

   The AppleTalk protocol provides very little information that can be
   used with the Job Monitoring MIB.  The Macintosh print drivers are
   able to provide information concerning the user and document name but
   imbed this information in the PDL, which is typically PostScript.
   The preferred jmJobSubmissionID is constructed from the information
   in the PostScript file, as defined in section 9.0.

3.1  jmJobSubmissionID Mapped to AppleTalk

   An alternative jmJobSubmissionID may be constructed from the
   Connection Identifier contained in the AppleTalk Printer Access
   Protocol (PAP) header.  Since the Connection Id is not readily
   available in any of the defined AppleTalk implementations, this
   approach may be of little utility.

   octet 1:   'A'

   octets 2-40:  Contains the AppleTalk printer name, with the first
                 character of the name in octet 2.  AppleTalk printer
                 names are a maximum of 31 characters.  Any unused
                 portion of this field shall be filled with spaces.

   octets 41-48:  '00000XXX', where 'XXX' is the decimal (ASCII coded)
                  representation of the Connection Id.

3.2  Other AppleTalk Mappings

   No other Job MIB objects or parameters can be derived from
   information available in the AppleTalk headers

4.0  INTERNET PRINTING PROTOCOL (IPP)

   The Internet Printing Protocol [IPP] supports printing using any one
   of the three possible configurations.  For configuration 2, the
   mapping defined herein is performed on an agent within the server.
   Otherwise, the mapping is performed on an agent within the printer.





Bergman                      Informational                      [Page 6]


RFC 2708            Job Submission Protocol Mapping        November 1999


4.1  jmJobSubmissionID Mapped to IPP

   IPP contains a rich set of parameters which allow several methods of
   creating the jmJobSubmissionID object.  To prevent interoperability
   problems, the preferred method is to use the IPP job-uri attribute as
   follows:

   octet 1:   '4'

   octets 2-40:  Contains the IPP job-uri job description attribute
                 generated by the printer.  (The job-uri is returned to
                 the client by IPP.)  If the job-uri is less than 40
                 octets, the left-most character in the string shall
                 appear in octet position 2.  Any unused portion of this
                 field shall be filled with spaces.  Otherwise, only the
                 last 39 bytes shall be included.

   octets 41-48:  Contains the decimal (ASCII coded) representation of
                  the job-id job description attribute.  Leading zeros
                  shall be inserted to fill the entire 8 octet field.

   NOTE - Since IPP returns the "job-identifier" attribute with the
   jmJobIndex value for a job when the job is submitted, the use of the
   jmJobSubmissionID table should not be needed by a management
   application.  See Section 1.0.

4.2  jmJobIndex Mapped to IPP

   The job index (jmJobIndex) assigned by the SNMP job monitoring agent
   is returned to the client by IPP as the job-id job description
   attribute.  (Since IPP does not require consecutively generated job-
   ids, the agent may receive jobs from multiple clients and can assign
   jmJobIndex in an ascending sequence independent of the submitting job
   client.)  The IPP job-id must be restricted to the range of 1 to
   99,999,999 (decimal) to allow the value to be properly represented in
   jmJobSubmissionID.















Bergman                      Informational                      [Page 7]


RFC 2708            Job Submission Protocol Mapping        November 1999


4.3  Other MIB Objects Mapped to IPP

   MIB Object                       | IPP Job attribute
   ---------------------------------+-----------------------------------
   jmJobState                       | job-state
   jmJobStateReasons1               | job-state-reasons (note 1)
   jmNumberOfInterveningJobs        | number-of-intervening-jobs
   jmJobKOctetsPerCopyRequested     | job-k-octets
   jmJobKOctetsProcessed            | job-k-octets-processed
   jmJobImpressionsPerCopyRequested | job-impressions
   jmJobImpressionsCompleted        | job-impressions-completed
   jmJobOwner                       | job-originating-user-name

   Notes:
   ------
   1. jmJobStateReasons1 is a bit map which can describe up to 31 job
      state reasons.  Also the IPP "job-state-reasons" attribute is a
      multi-valued attribute with each value being a keyword.  The IPP
      condition may change multiple bits in this object.  The IPP "job-
      state-reasons" attribute may also change one or more of the
      jobStateReasonsN attributes (see section 4.4).


4.4  The Attribute Group Mapped to IPP

   The following mappings are required if the listed IPP job template
   attribute is provided.
























Bergman                      Informational                      [Page 8]


RFC 2708            Job Submission Protocol Mapping        November 1999


MIB attribute              | IPP job attribute            | Data type
---------------------------+------------------------------+-------------
jobStateReasonsN(N=2, 3, 4)| job-state-reasons (note 3)   | Integer
jobCodedCharSet            | attributes-charset (note 1)  | Octet String
jobNaturalLanguageTag      | attributes-natural-language  | Octet String
jobURI                     | job-uri                      | Octet String
jobName                    | job-name                     | Octet String
physicalDevice             | output-device-assigned       | Octet String
numberOfDocuments          | number-of-documents          | Integer
jobPriority                | job-priority                 | Integer
jobHoldUntil               | job-hold-until               | Octet String
sides                      | sides (note 2)               | Integer
finishing                  | finishings                   | Integer
printQualityRequested      | print-quality                | Integer
printerResolutionRequested | printer-resolution           | Integer
jobCopiesRequested         | copies (note 4)              | Integer
documentCopiesRequested    | copies (note 4)              | Integer
jobCollationType           | multiple-document-handling   | Integer
sheetsRequested            | job-media-sheets             | Integer
sheetsCompleted            | job-media-sheets-completed   | Integer
mediumRequested            | media                        | Octet String
jobSubmissionTime          | time-at-submission           | Integer
jobStartedProcessingTime   | time-at-processing           | Integer
jobCompletionTime          | time-at-completed            | Integer

   Notes:
   ------
   1. jobCodedCharSet is an enum from the IANA registry which is also
      used in the Printer MIB.  The IPP attributes-charset is the name
      (MIME preferred name) of the character set.
   2. The Job MIB sides attribute uses the integer values "1" and "2".
      The IPP sides attribute uses three keywords.
   3. jobStateReasonsN are three attributes (N=2, 3, 4).  Also the IPP
      "job-state-reasons" attribute is a multi-valued attribute with
      each value being a keyword.  The IPP condition may change multiple
      bits in one or more of these Job MIB attributes.  See also
      jmJobStateReasons1 in section 4.3.
   4. The IPP "copies" attribute maps to the Job MIB:
      (1) jobCopiesRequested when the job has only one document OR IPP
          "multiple-document-handling" is 'single-valued'
      (2) documentCopiesRequested, in which case the MIB value is the
          total number of document copies that the job will produce as a
          whole.








Bergman                      Informational                      [Page 9]


RFC 2708            Job Submission Protocol Mapping        November 1999


5.0  INTELLIGENT PRINTER DATA STREAM (IPDS)

   The IPDS datastream facilitates a close relationship between the
   print supervisor (Print Services Facility - PSF) and the printer.
   There are PSF applications for UNIX, Windows, OS/2, OS/400 and host
   operating systems such as VM, MVS and VSE. Together, PSF and IPDS
   represent a complete, mature and robust job management framework
   which includes font and resource management, page progress tracking,
   job cancellation, complete error recovery and end-user notification.
   Because PSF and the printer correspond via the use of locally
   assigned IDÆs, there is a limited amount of clear text information
   provided during submission for use by the Job MIB.

5.1  jmJobSubmissionId Mapped to IPDS

   For IPDS on the MVS or VSE platform:

   octet 1:   'E'

   octets 2-40:  Contains bytes 2-27 of the XOH Define Group Boundary
                 Group ID triplet.  Octet position 2 must carry the
                 value x'01'.  Bytes 28-40 must be filled with spaces.

   octets 41-48:  Contains a decimal (ASCII coded) representation of the
                  jmJobIndex assigned by the agent.  Leading zeros shall
                  be inserted to fill the entire 8 octet field.

   For IPDS on the VM platform:

   octet 1:   'F'

   octets 2-40:  Contains bytes 2-31 of the XOH Define Group Boundary
                 Group ID triplet.  Octet position 2 must carry the
                 value x'02'.  Bytes 32-40 must be filled with spaces.

   octets 41-48:  Contains a decimal (ASCII coded) representation of the
                  jmJobIndex assigned by the agent.  Leading zeros shall
                  be inserted to fill the entire 8 octet field.

   For IPDS on the OS/400 platform:

   octet 1:   'G'

   octets 2-40:  Contains bytes 2-36 of the XOH Define Group Boundary
                 Group ID triplet.  Octet position 2 must carry the
                 value x'03'.  Bytes 37-40 must be filled with spaces.





Bergman                      Informational                     [Page 10]


RFC 2708            Job Submission Protocol Mapping        November 1999


   octets 41-48:  Contains a decimal (ASCII coded) representation of the
                  jmJobIndex assigned by the agent.  Leading zeros shall
                  be inserted to fill the entire 8 octet field.

5.2  The Attribute Group Mapped to IPDS

For MVS/VSE:

MIB attribute                     | IPDS XOH DGB Group ID | Data type
----------------------------------+-----------------------+-------------
jobSourcePlatformType sptMVS(7)   | Byte 2 = x'01'        | Integer
jobName                           | Bytes 4-11            | Octet String


For VM:

MIB attribute                     | IPDS XOH DGB Group ID | Data type
----------------------------------+-----------------------+-------------
jobSourcePlatformType sptVM(8)    | Byte 2 = x'02'        | Integer
fileName                          | Bytes 4-11            | Octet String


For OS/400:

MIB attribute                     | IPDS XOH DGB Group ID | Data type
----------------------------------+-----------------------+-------------
jobSourcePlatformType sptOS400(9) | byte 2 = x'03'        | Integer
fileName                          | Bytes 23-32           | Octet String
jobName                           | Bytes 37-46           | Octet String

6.0  DOCUMENT PRINTING APPLICATION (DPA)

   The ISO 10175 Document Printing Application (DPA) [DPA] supports
   printing using any one of the three possible configurations.  For
   configuration 2, the mapping defined herein is performed on a server.
   Otherwise, the mapping is performed on an agent within the printer.

6.1  jmJobSubmissionID Mapped to DPA

   DPA contains a rich set of parameters which allow several methods of
   creating the jmJobSubmissionID object.  To prevent interoperability
   problems, the preferred method is to use the DPA job-owner attribute
   as follows:








Bergman                      Informational                     [Page 11]


RFC 2708            Job Submission Protocol Mapping        November 1999


   octet 1:   '0'

   octets 2-40:  Contains the DPA job-owner attribute supplied by the
                 submitter.  If the job-owner is less than 40 octets,
                 the left-most character in the string shall appear in
                 octet position 2.  Any unused portion of this field
                 shall be filled with spaces.  Otherwise, only the last
                 39 bytes shall be included.

   octets 41-48:  Contains an 8-digit sequential decimal number.

6.2  jmJobIndex Mapped to DPA

   The job index (jmJobIndex) assigned by the SNMP job monitoring agent
   is returned to the client by DPA as a decimal digit string as the
   value of the DPA job-identifier attribute.  (Since DPA does not
   require consecutively generated job-identifiers, the agent may
   receive jobs from multiple clients and can assign the jmJobIndex in
   an ascending sequence independent of the submitting job client.)  The
   DPA job-identifier must be restricted to the range of 1 to 99,999,999
   (decimal) to allow the value to be properly represented in
   jmJobSubmissionID.

   NOTE - Since DPA returns the "job-identifier" attribute with the
   jmJobIndex value for a job when the job is submitted, the use of the
   jmJobSubmissionID table should not be needed by a management
   application.  See Section 1.0.

6.3  Other MIB Objects Mapped to DPA

   MIB Object                       | DPA Job attribute
   ---------------------------------+------------------------------------
   jmJobState                       | job-state
   jmJobStateReasons1               | job-state-reasons (note 2)
   jmNumberOfInterveningJobs        | intervening-jobs
   jmJobKOctetsPerCopyRequested     | total-job-octets (notes 1, 3)
   jmJobKOctetsProcessed            | job-octets-completed (note 1)
   jmJobImpressionsPerCopyRequested | job-impression-count (note 3)
   jmJobImpressionsCompleted        | impressions-completed
   jmJobOwner                       | job-owner

   Notes:
   ------
   1. jmJobKOctetsPerCopyRequested and jmJobKOctetsProcessed is in K
      octets while the DPA job-total-octets and job-octets-completed is
      in octets and is 63-bits of significance.





Bergman                      Informational                     [Page 12]


RFC 2708            Job Submission Protocol Mapping        November 1999


   2. jmJobStateReasons1 is a bit map which can describe up to 31 job
      state reasons.  Also the DPA "job-state-reasons" attribute is a
      multi-valued attribute with each value being an object identifier
      (OID).  The DPA condition may change multiple bits in this object.
      The DPA condition may also change one or more of the
      jobStateReasonsN attributes (see section 4.4)
   3. DPA octets include the multiplication factor due to job and
      document copies, while the MIB values do not.

6.4  The Attribute Group Mapped to DPA

   The following mappings are required if the listed DPA job attribute
   is provided.

MIB attribute              | DPA job attribute            |IPP Data type
---------------------------+------------------------------+-------------
jobStateReasonsN(N=2, 3, 4)| job-state-reasons (note 2)   | Integer
jobCodedCharSet            | (note 1)                     | Octet String
jobAccountName             | accounting-information       | Octet String
jobName                    | job-name                     | Octet String
deviceNameRequested        | printer-name-requested       | Octet String
physicalDevice             | printers-assigned            | Octet String
numberOfDocuments          | number-of-documents          | Integer
fileName                   | file-name                    | Octet String
documentName               | document-name                | Octet String
jobComment                 | job-comment                  | Octet String
documentFormat             | document-format              | Octet String
jobPriority                | job-priority                 | Integer
jobProcessAfterDateAndTime | job-print-after              | Octet String
outputBin                  | results-profile.output-bin   | Octet String
sides                      | sides (note 3)               | Integer
finishing                  | job-finishing, finishing     | Integer
printQualityRequested      | print-quality                | Integer
printerResolutionRequested | default-printer-resolution   | Integer
                           |  (note 4)                    |
jobCopiesRequested         | results-profile.job-copies   | Integer
jobCopiesCompleted         | job-copies-completed         | Integer
documentCopiesRequested    | copy-count (note 5)          | Integer
documentCopiesCompleted    | copies-completed (note 6)    | Integer
sheetsRequested            | job-media-sheet-count        | Integer
sheetsCompleted            | job-media-sheets-completed   | Integer
pagesRequested             | job-page-count               | Integer
pagesCompleted             | pages-completed              | Integer
mediumRequested            | page-media-select,           | Octet String
                           |  default-medium              |
jobSubmissionTime          | submission-time (note 7)     | Octet String
jobStartedProcessingTime   | started-printing-time (note 7) Octet String
jobCompletionTime          | completion-time (note 7)     | Octet String



Bergman                      Informational                     [Page 13]


RFC 2708            Job Submission Protocol Mapping        November 1999


 Notes:
 ------
   1. Every DPA attribute is tagged indicating the coded character set
      to be used for that attribute.
   2. jobStateReasonsN are three attributes (N=2, 3, 4).  The DPA
      condition may change one or more of the bits in one or more of
      these Job MIB items.  Also the DPA job-state-reasons is a multi-
      valued attribute with each value being an OBJECT IDENTIFIER (OID).
   3. The Job MIB sides attribute is an integer '1' or '2' while the DPA
      sides attribute has one of six OID values that includes plex.
   4. printerResolutionRequested has x and y resolution and is intended
      to override the resolution instruction in the document, if any,
      while the DPA default-printer-resolution is the same in x and y
      and only takes effect if the document does not contain a
      resolution instruction
   5. The DPA "copy-count" attribute is a per-document attribute, so the
      MIB value is the sum of the documents' "copy-count" values times
      the job's "results-profile.job-copies" value.
   6. The DPA "copies-completed" attribute is a per-document attribute,
      so the MIB value is the sum of the documents' "copies-completed"
      values times the job's "results-profile.job-copies" value.
   7. The DPA GeneratlizedTime data type is defined by ISO 8824 (ISO-
      8824) while the MIB DateAndTime is defined by SNMPv2-TC (SNMPv2-
      TC).

7.0  NOVELL DISTRIBUTED PRINT SERVICE (NDPS)

   Novell Distributed Print Services is a DPA based job submission
   protocol that conforms to configuration 3.

7.1  jmJobSubmissionID Mapped to NDPS

   NDPS supports the generation of a properly formatted
   jmJobSubmissionID for use in the Job MIB, via the attribute ndps-
   att-job-identifier.

7.2  jmJobIndex Mapped to NDPS

   NDPS defines the attribute ndps-att-job-identifier-on-printer that
   can be used to return the value of jmJobIndex to the NDPS client. See
   Section 1.0.










Bergman                      Informational                     [Page 14]


RFC 2708            Job Submission Protocol Mapping        November 1999


7.3  Other MIB Objects Mapped to NDPS

MIB Object                       | NDPS Parameter
---------------------------------+--------------------------------------
jmJobState                       | ndps-att-current-job-state (note 1)
jmJobStateReasons1               | ndps-att-job-state-reasons (note 2)
jmNumberOfInterveningJobs        | ndps-att-intervening-jobs
jmJobKOctetsPerCopyRequested     | ndps-att-total-job-octets (notes 3,4)
jmJobKOctetsProcessed            | ndps-att-octets-completed (note 3)
jmJobImpressionsPerCopyRequested | ndps-att-job-impressions-count
jmJobImpressionsCompleted        | ndps-att-impressions-completed
jmJobOwner                       | ndps-att-job-owner (note 5)

   Notes:
   ------
   1. Some of the NDPS job states must be represented by both a
      jmJobState and a jmJobStateReasons1 object or a jobStateReasonsN
      attribute (N=2, 3, 4).
   2. The NDPS job state reasons may be mapped to either the object
      jmJobStateReasons1 or the attribute jobStateReasonsN (N=2, 3, 4).
   3. jmJobKOctetsPerCopyRequested and jmJobKOctetsProcessed is in K
      octets while the NDPS ndps-att-job-total-octets and ndps-att-job-
      octets-completed is in octets and is 63-bits of significance.
   4. NDPS octets include the multiplication factor due to job and
      document copies, while the MIB values do not.
   5. The Job MIB object must be multiplied by the attribute
      jobCopiesRequested to obtain the NDPS attribute value, if multiple
      copies have been requested.

7.4  The Attribute Group Mapped to NDPS

   The following mappings are required if the listed PJL attribute or
   command option is provided.


















Bergman                      Informational                     [Page 15]


RFC 2708            Job Submission Protocol Mapping        November 1999


MIB attribute              | NDPS parameter               | Data type
---------------------------+------------------------------+-------------
jobStateReasonsN(N=2, 3, 4)| ndps-job-state-reasons       | Integer
jobAccountName             | ndps-att-job-owner           | Octet String
jobName                    | ndps-att-job-name            | Octet String
jobOriginatingHost         | ndps-att-job-originator      | Octet String
deviceNameRequested        | ndps-att-printer-name--      | Octet String
                           |  requested                   |
numberOfDocuments          | ndps-att-number-of-documents | Integer
fileName                   | ndps-att-document-file-name  | Octet String
documentName               | ndps-att-document-name       | Octet String
jobComment                 | ndps-att-job-comment         | Octet String
documentFormatIndex        | ndps-att-prtInterpreterIndex | Integer
documentFormat             | ndps-att-document-format     | Integer
jobPriority                | ndps-att-job-priority        | Integer
jobProcessAfterDateAndTime | ndps-att-job-print-after     | Octet String
outputBin                  | ndps-att-results-profile     | Integer
                           |  (note 1)                    |
sides                      | ndps-att-sides (note 2)      | Integer
finishing                  | ndps-att-job-finishing       | Integer
printQualityRequested      | ndps-att-print-quality       | Integer
printerResolutionRequested | ndps-att-default-printer--   |
                           |  resolution (note 3)         | Integer
printerResolutionUsed      | ndps-att-default-resolutions--
                           |  used                        | Integer
jobCopiesRequested         | ndps-att-results-profile     | Integer
                           |  (note 4)                    |
jobCopiesCompleted         | ndps-att-job-copies-completed| Integer
documentCopiesRequested    | ndps-att-copy-count (note 5) | Integer
documentCopiesCompleted    | ndps-att-copies-completed    | Integer
                           |  (note 6)                    |
sheetsRequested            | ndps-att-job-media--         |
                           |  sheet-count                 | Integer
sheetsCompleted            | ndps-att-media-sheets--      |
                           |  completed                   | Integer
mediumConsumed             | ndps-att-media-used          | Integer
jobSubmissionToServerTime  | ndps-att-submission-time     | Octet String
                           |  (note 7)                    |
jobSubmissionTime          | ndps-att-started-printing-time Octet String
                           |  (note 7)                    |
jobCompletionTime          | ndps-att-completion-time     | Octet String
                           |  (note 7)                    |
   Notes:
   ------
   1. The output-bin field in ndps-att-results-profile is to be used.
   2. The Job MIB sides attribute is an integer '1' or '2' while the
      NDPS sides attribute has one of six OID values that includes plex.




Bergman                      Informational                     [Page 16]


RFC 2708            Job Submission Protocol Mapping        November 1999


   3. printerResolutionRequested has x and y resolution and is intended
      to override the resolution instruction in the document, if any,
      while the ndps-att-default-printer-resolution is the same in x and
      y and only takes effect if the document does not contain a
      resolution instruction
   4. The job-copies field in ndps-att-results-profile is to be used.
   5. The NDPS "copy-count" attribute is a per-document attribute, so
      the MIB value is the sum of the documents' "copy-count" values
      times the job's "results-profile.job-copies" value.
   6. The NDPS "copies-completed" attribute is a per-document attribute,
      so the MIB value is the sum of the documents' "copies-completed"
      values times the job's "results-profile.job-copies" value.
   7. The NDPS GeneratlizedTime data type is defined by ISO 8824 (ISO-
      8824) while the MIB DateAndTime is defined by SNMPv2-TC (SNMPv2-
      TC).

8.0  PRINTER JOB LANGUAGE (PJL)

   PJL [PJL] has been developed by Hewlett-Packard to provide job
   control information to the printer and status information to
   applications, independent of the PDL.

8.1  jmJobSubmissionID Mapped to PJL

   PJL has defined the SUBMISSIONID option for the JOB command which
   indicates a properly formatted jmJobSubmissionID for use in the Job
   MIB.  The PJL JOB command is presented at the start of a print job
   with options that apply only the attached job.  The syntax for this
   command option is:

      @PJL JOB SUBMISSIONID = "id string"

   Driver software that implements this PJL command option must provide
   the "id string" in one of the client version formats specified in the
   Job MIB for jmJobSubmissionID.

   For drivers that are not able to create the SUBMISSIONID option, it
   is recommended that jmJobSubmissionID format 0 be created by the
   agent using the PJL attribute DocOwner or DocOwnerId.

   octet 1:   '0'

   octets 2-40:  Contains the string associated with DocOwner or
                 DocOwnerId.  If the string is less than 40 octets, the
                 left-most character in the string shall appear in octet






Bergman                      Informational                     [Page 17]


RFC 2708            Job Submission Protocol Mapping        November 1999


                 position 2.  Otherwise, only the last 39 bytes shall be
                 included.  Any unused portion of this field shall be
                 filled with spaces.  If DocOwner or DocOwnerId cannot
                 be obtained, this field shall be blank.


   octets 41-48:  Contains the value of jmJobIndex associated with the
                  job.  Leading zeros shall be inserted to fill the
                  entire 8 octet field.

8.2  jmJobIndex Mapped to PJL

   PJL does not provide a value that can be mapped to jmJobIndex.

8.3  Other MIB Objects Mapped to PJL

   MIB Object            | PJL Job attribute
   ----------------------+------------------------------------
   jobOwner              | DocOwner or DocOwnerId attribute

8.4  The Attribute Group Mapped to PJL

   The following mappings are required if the listed PJL attribute or
   command option is provided.

MIB attribute         | PJL attribute or command option  | Data type
----------------------+----------------------------------+--------------
serverAssignedJobName | DocName attribute or the command | Octet String
                      |  @PJL JOB Name = "string"        | Octet String
submittingServerName  | SrcServerName attribute          | Octet String
jobOriginatingHost    | SrcPort attribute                | Octet String
queueNameRequested    | SrcQ attribute                   | Octet String
fileName              | JobFName attribute               | Octet String
jobComment            | JobDesc attribute                | Octet String
jobSubmissionTime     | TimeSubmit attribute             | Octet String

9.0  POSTSCRIPT

   The PostScript PDL permits comment fields which can be used by
   application drivers to include job information.  Although there are
   no restrictions or requirements as to what information may be
   included, many drivers include job owner and/or document name.









Bergman                      Informational                     [Page 18]


RFC 2708            Job Submission Protocol Mapping        November 1999


9.1  jmJobSubmissionID Mapped to PostScript

   The use of a standard format job submission id comment string will
   allow interoperability of printers and drivers from multiple vendors.
   The following comment string format is recommended for use with
   PostScript level 1 and level 2 data streams.

      %%JMPJobSubmissionId:(id-string)

   where "id string" can be any jmJobSubmissionID format reserved for
   clients.

9.2  Other MIB Objects and Attributes Mapped to PostScript

   No Other mappings from PostScript comment strings are recommended,
   but many Job MIB objects and attributes can be defined using vendor
   unique comment strings.

10.0  NETWARE PSERVER

   The NetWare PServer job submission protocol is implemented in a
   client- server-printer system on the server to printer link as
   defined in configuration 3.

10.1  jmJobSubmissionID Mapped to PServer

   octet 1:   'B'

   octets 2-40:  Contains the Directory Path Name of the agent as
                 recorded by the Novell File Server in the queue
                 directory.  If the string is less than 40 octets, the
                 left-most character in the string shall appear in octet
                 position 2.  Otherwise, only the last 39 bytes shall be
                 included.  Any unused portion of this field shall be
                 filled with spaces.

   octets 41-48:  '000XXXXX'  The decimal (ASCII coded) representation
                  of the Job Number as per the NetWare File Server Queue
                  Management Services.

10.2  jmJobIndex Mapped to PServer

   The job index (jmJobIndex) is assigned by the SNMP job monitoring
   agent and is independent of the Job Number assigned by the NetWare
   File Server Queue Management Services.  This will allow the SNMP
   agent to track jobs received from multiple sources.





Bergman                      Informational                     [Page 19]


RFC 2708            Job Submission Protocol Mapping        November 1999


10.3  Other MIB Objects Mapped to PJL

   MIB Object            | PServer Job attribute
   ----------------------+--------------------------------------------
   jobOwner              | Client Id Number

10.4  The Attribute Group Mapped to PServer

   The following mappings are required if the listed PServer parameter
   is provided in the Novell File Server queue directory.

MIB attribute              | PServer parameter           | Data type
---------------------------+-----------------------------+--------------
serverAssignedJobName      | Job File Name               | Octet String
queueNameRequested         | Queue Id                    | Integer
physicalDevice             | Server Id Number            | Integer
jobComment                 | Job Description             | Octet String
jobPriority                | (note 1)                    | Integer
jobProcessAfterDateAndTime | Target Execution Time       | Octet String
jobCopiesRequested         | Number of Copies            | Integer
mediumRequested            | Form Name                   | Octet String
jobSubmissionToServerTime  | Job Entry Time              | Octet String

   Notes:
   ------
   1. The job priority is determined by the priority assigned to the
      queue that contains the job.  Each queue can be assigned a unique
      priority and the priority of the job is inherited from the queue.

11.0  NETWARE NPRINTER or RPRINTER

   The NetWare NPrinter/RPrinter protocol was designed to transfer print
   data from a Novell File Server to a printer attached directly to a
   local port (e.g. parallel or serial) on a PC.  NPrinter/RPrinter is
   an extremely lightweight printing protocol.  Consequently, no
   information required by the Job Monitoring MIB is provided and a
   meaningful jmJobSubmissionID cannot be generated.

   It is recommended that an additional job submission layer, such as
   PJL or another vendor private protocol,  be included on top of
   NPrinter/RPrinter to provide the required information.  The mapping
   should then be performed according to the recommendations of the
   higher layer submission protocol.








Bergman                      Informational                     [Page 20]


RFC 2708            Job Submission Protocol Mapping        November 1999


12.0  SERVER MESSAGE BLOCK (SMB) PROTOCOL

   The Server Message Block protocol is used with several PC Network
   operating systems, such as Microsoft Windows for Workgroups, IBM LAN
   Server, and Artisoft Lantastic.  SMB systems supporting the Job
   Monitoring MIB will conform to either configuration 1 or 3.

12.1  jmJobSubmissionID Mapped to SMB

   octet 1:   'C'

   octets 2-40:  Contains a decimal (ASCII coded) representation of the
                 16 bit SMB Tree Id field, which uniquely identifies the
                 connection that submitted the job to the printer.  The
                 most significant digit of the numeric string shall be
                 placed in octet position 2.  All unused portions of
                 this field shall be filled with spaces.  The SMB Tree
                 Id has a maximum value of 65,535.

   octets 41-48:  Contains a decimal (ASCII coded) representation of the
                  File Handle returned from the printer agent to the
                  client in response to a Create Print File command.
                  Leading zeros shall be inserted to fill the entire 8
                  octet field.

12.2  jmJobIndex Mapped to SMB

   It is strongly recommended that the File Handle returned from the
   printer agent be identical to jmJobIndex.  If these items are
   identical, there is no need for the client application to perform a
   search on jmJobSubmissionID.  To be compatible with the 16 bit field
   allocated to this value by SMB, the maximum jmJobIndex is 65,535.

12.3  Other MIB objects Mapped to SMB

   MIB Object      | SMB Parameter
   ----------------+------------------------------------------------
   jmJobOwner      | SMB User Id field (note 1)

   Notes:
   ------
   1. A decimal (ASCII coded) representation of the SMB User Id numeric
      shall be presented as jmJobOwner.








Bergman                      Informational                     [Page 21]


RFC 2708            Job Submission Protocol Mapping        November 1999


13.0  TRANSPORT INDEPENDENT PRINTER/SYSTEM INTERFACE (TIP/SI)

   The TIP/SI protocol, although currently specified as a part of the
   IEEE 1284 parallel port standards [TIP/SI], was originally developed
   as a network protocol.  TIP/SI thus has the potential of being
   integrated into any network or non-network configuration.

13.1  jmJobSubmissionID Mapped to TIP/SI

   octet 1:   'D'

   octets 2-40:  Contains the Job Name from the Job Control-Start Job
                 (JC-SJ) command.  If the Job Name portion is less than
                 40 octets, the left-most character in the string shall
                 appear in octet position 2.  Any unused portion of this
                 field shall be filled with spaces.  Otherwise, only the
                 last 39 bytes shall be included.

   octets 41-48:  Contains a decimal (ASCII coded) representation of the
                  jmJobIndex assigned by the agent.  Leading zeros shall
                  be inserted to fill the entire 8 octet field.

13.2  jmJobIndex Mapped to TIP/SI

   jmJobIndex is returned to the client as the Printer Assigned Job Id
   in a Job Control-Start Job (JC-SJ) response packet.  To be compatible
   with the 16 bit field allocated to this value by TIP/SI, the maximum
   jmJobIndex is 65,535.

13.3  Other MIB Objects Mapped to TIP/SI

   MIB Object             | TIP/SI Parameter
   -----------------------+---------------------------------------------
   jmJobOwner             | User string

13.4  The Attribute Group Mapped to TIP/SI

  MIB attribute         | TIP/SI information              | Data type
  ----------------------+---------------------------------+-------------
  jobName               | Job Name string                 | Octet String
  jobComment            | Additional Information string   | Octet String










Bergman                      Informational                     [Page 22]


RFC 2708            Job Submission Protocol Mapping        November 1999


14.0  Security Considerations

   This document provides mapping recommendations of job submission
   protocols for use with the Job Monitoring MIB. The mapping procedures
   defined do not enhance or compromise any security provisions
   available within the job submission protocols contained within this
   document.

   The security considerations specified for the Job Monitoring MIB
   [JobMIB] are also unaffected by any of the recommendations in this
   document.

   The security provisions available in the job submission protocols are
   documented in the appropriate specifications that define the
   protocols.  The degree of security available varies from very good,
   for protocols such as the Internet Printing Protocol [IPP], to non-
   existent, for example the Line Printer Daemon Protocol [LPD].

   Since the defined mapping operation occurs as a secondary operation
   after the user has been authenticated and there is no storage of any
   authorization credentials other than the user name, no security
   breaches are anticipated.  Also, the Job MIB does not provide any
   back-door mechanism for access to any other security parameters.
   However, implementers must always consider the impact of the defined
   mapping procedures upon the security model desired from the protocol.

15.0  REFERENCES

   [DPA]        ISO/IEC 10175-1:1996(E), "Information technology - Text
                and office systems - Document Printing Application (DPA)
                - Part 1: Abstract service definition and procedures",
                JTC1/SC18.

   [IPP]        deBry, R., Hastings, T., Herriot, R., Issaacson, S. and
                P. Powell, "The Internet Printing Protocol/1.0: Model
                and Semantics", RFC 2566, April 1999.

   [ISO-8824]   ISO/IEC 8824:1990, "Information technology - Open
                Systems Interconnection - Specification of Abstract
                Syntax Notation (ASN.1)".

   [JobMIB]     Bergman, R., Hastings, T., Isaacson, S. and H. Lewis,
                "The Job Monitoring MIB - V1.0", RFC 2707, November
                1999.

   [LPD]        McLaughlin, L., "Line Printer Daemon Protocol", RFC
                1179, August 1990.




Bergman                      Informational                     [Page 23]


RFC 2708            Job Submission Protocol Mapping        November 1999


   [PJL]        Printer Job Language Technical Reference Manual,
                Hewlett-Packard part number 5021-0328.

   [PrtMIB]     Smith, R., Wright, F., Hastings, T., Zilles, S. and J.
                Gyllenskog, "Printer MIB", RFC 1759, March 1995.

   [SNMPv2-TC]  McCloghrie, K., Perkins, D. and J. Schoenwaelder,
                "Textual Conventions for SMIv2", STD 58, RFC 2579, April
                1999.

   [TIP/SI]     IEEE Standard 1284.1, Transport Independent
                Printer/System Interface.

16.0  Authors' Addresses

   This document was created with significant contributions from the
   following individuals.

   Ron Bergman (Editor)
   Dataproducts Corp.
   1757 Tapo Canyon Road
   Simi Valley, CA 93063-3394

   Phone: 805-578-4421
   Fax:  805-578-4001
   EMail: rbergman@dpc.com


   Tom Hastings
   Xerox Corporation, ESAE-231
   701 S. Aviation Blvd.
   El Segundo, CA   90245

   Phone: 310-333-6413
   Fax:   310-333-5514
   EMail: hastings@cp10.es.xerox.com


   Scott A. Isaacson
   Novell, Inc.
   122 E 1700 S
   Provo, UT   84606

   Phone: 801-861-7366
   Fax:   801-861-4025
   EMail: scott_isaacson@novell.com





Bergman                      Informational                     [Page 24]


RFC 2708            Job Submission Protocol Mapping        November 1999


   Harry Lewis
   IBM Corporation
   6300 Diagonal Hwy
   Boulder, CO 80301

   Phone: (303) 924-5337
   Fax:   (303) 924-4662
   EMail: harryl@us.ibm.com


   Bob Pentecost
   Hewlett-Packard Corporation
   11311 Chinden Boulevard
   Boise, ID 83714

   Phone: (208) 396-3312
   Fax:   (208) 396-4122
   EMail: bpenteco@boi.hp.com

   Send comments to the printmib WG using the Job Monitoring Project
   (JMP) Mailing List: jmp@pwg.org

   For further information, access the PWG web page under "JMP":
   http://www.pwg.org/

   Other Participants:

      Chuck Adams - Tektronix
      Keith Carter - IBM Corporation
      Angelo Caruso - Xerox
      Jeff Copeland - QMS
      Andy Davidson - Tektronix
      Mabry Dozier - QMS
      Lee Farrell - Canon
      David Kellerman - Northlake Software
      Rick Landau - Digital
      Jay Martin - Underscore
      Ira McDonald - Xerox
      Stuart Rowley - Kyocera
      Bob Setterbo - Adobe
      Gail Songer - EFI
      Mike Timperman - Lexmark
      William Wagner - DPI/Osicom
      Chris Wellens - Interworking Labs
      Rob Whittle - Novell
      Don Wright - Lexmark
      Lloyd Young - Lexmark




Bergman                      Informational                     [Page 25]


RFC 2708            Job Submission Protocol Mapping        November 1999


17.  Full Copyright Statement

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Bergman                      Informational                     [Page 26]