CLNS MIB for use with Connectionless Network Protocol (ISO 8473) and End System to Intermediate System (ISO 9542)
RFC 1238
| Document | Type |
RFC - Experimental
(June 1991)
Obsoletes RFC 1162
|
|
|---|---|---|---|
| Authors | |||
| Last updated | 2013-03-02 | ||
| Stream | Legacy stream | ||
| Formats | plain text html pdf htmlized bibtex | ||
| Stream | Legacy state | (None) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | RFC 1238 (Experimental) | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
RFC 1238
Network Working Group G. Satz
Request for Comments: 1238 cisco Systems, Inc.
Obsoletes: RFC 1162 June 1991
CLNS MIB
for use with
Connectionless Network Protocol (ISO 8473)
and
End System to Intermediate System (ISO 9542)
Status of this Memo
This memo defines an experimental portion of the Management
Information Base (MIB) for use with network management protocols in
TCP/IP-based internets. This is an Experimental Protocol for the
Internet community. Discussion and suggestions for improvement are
requested. Please refer to the current edition of the "IAB Official
Protocol Standards" for the standardization state and status of this
protocol. Distribution of this memo is unlimited.
Table of Contents
1. The Network Management Framework....................... 1
2. Objects ............................................... 2
2.1 Format of Definitions ................................ 2
3. Overview .............................................. 2
3.1 Textual Conventions .................................. 3
3.2 Changes from RFC 1162 ................................ 3
4. Definitions ........................................... 4
4.1 Textual Conventions .................................. 4
4.2 Groups in the CLNS MIB ............................... 4
4.3 The CLNP Group ....................................... 4
4.4 The CLNP Error Group ................................. 21
4.5 The ES-IS Group ...................................... 30
5. References ............................................ 31
6. Security Considerations ............................... 32
7. Author's Address....................................... 32
1. The Network Management Framework
The Internet-standard Network Management Framework consists of three
components. They are:
RFC 1155 which defines the SMI, the mechanisms used for describing
and naming objects for the purpose of management. RFC 1212
defines a more concise description mechanism, which is wholly
consistent with the SMI.
Satz [Page 1]
RFC 1238 CLNS MIB June 1991
RFC 1156 which defines MIB-I, the core set of managed objects for
the Internet suite of protocols. RFC 1213, defines MIB-II, an
evolution of MIB-I based on implementation experience and new
operational requirements.
RFC 1157 which defines the SNMP, the protocol used for network
access to managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
2. Objects
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1) [7]
defined in the SMI. In particular, each object has a name, a syntax,
and an encoding. The name is an object identifier, an
administratively assigned name, which specifies an object type. The
object type together with an object instance serves to uniquely
identify a specific instantiation of the object. For human
convenience, we often use a textual string, termed the OBJECT
DESCRIPTOR, to also refer to the object type.
The syntax of an object type defines the abstract data structure
corresponding to that object type. The ASN.1 language is used for
this purpose. However, the SMI [3] purposely restricts the ASN.1
constructs which may be used. These restrictions are explicitly made
for simplicity.
The encoding of an object type is simply how that object type is
represented using the object type's syntax. Implicitly tied to the
notion of an object type's syntax and encoding is how the object type
is represented when being transmitted on the network.
The SMI specifies the use of the basic encoding rules of ASN.1 [8],
subject to the additional requirements imposed by the SNMP.
2.1. Format of Definitions
Section 4 contains the specification of all object types contained in
this MIB module. The object types are defined using the conventions
defined in the SMI, as amended by the extensions specified in [9].
3. Overview
The objects defined in this MIB module are be used when the ISO
Connectionless-mode Network Protocol [10] and End System to
Satz [Page 2]
RFC 1238 CLNS MIB June 1991
Intermediate System [11] protocols are present. No assumptions are
made as to what underlying protocol is being used to carry the SNMP.
This memo uses the string encoding of [12] to textually describe OSI
addresses.
3.1. Textual Conventions
A new data type is introduced as a textual convention in this MIB
document. This textual conventions enhance the readability of the
specification and can ease comparison with other specifications if
appropriate. It should be noted that the introduction of this
textual convention has no effect on either the syntax nor the
semantics of any managed objects. The use of this is merely an
artifact of the explanatory method used. Objects defined in terms of
this methods are always encoded by means of the rules that define the
primitive type. Hence, no changes to the SMI or the SNMP are
necessary to accommodate this textual convention which are adopted
merely for the convenience of readers and writers in pursuit of the
elusive goal of clear, concise, and unambiguous MIB documents.
The ASN.1 type ClnpAddress is used to denote an OSI address. This
consists of a string of octets. The first octet of the string
contains a binary value in the range of 0..20, and indicates the the
length in octets of the NSAP. Following the first octet, is the
NSAP, expressed in concrete binary notation, starting with the most
significant octet. A zero- length NSAP is used as a "special"
address meaning "the default NSAP" (analogous to the IP address of
0.0.0.0). Such an NSAP is encoded as a single octet, containing the
value 0. All other NSAPs are encoded in at least 4 octets.
3.2. Changes from RFC 1162
Features of this MIB include:
(1) The managed objects in this document have been defined
using the conventions defined in the Internet-standard
SMI, as amended by the extensions specified in [9]. It
must be emphasized that definitions made using these
extensions are semantically identically to those in RFC
1162.
(2) The PhysAddress textual convention from MIB-II has been
introduced to represent media addresses.
(3) The clnpRoutingDiscards, clnpRouteMetric5, and
clnpRouteInfo objects have been defined.
Satz [Page 3]
RFC 1238 CLNS MIB June 1991
(4) The ClnpAddress type was mistakenly given a tag in RFC
1162. This error has been corrected.
4. Definitions
CLNS-MIB DEFINITIONS ::= BEGIN
IMPORTS
experimental, Counter
FROM RFC1155-SMI
PhysAddress
FROM RFC-1213
OBJECT-TYPE
FROM RFC-1212;
-- This MIB module uses the extended OBJECT-TYPE macro as
-- defined in [9]
-- the CLNS MIB module
clns OBJECT IDENTIFIER ::= { experimental 1 }
-- textual conventions
ClnpAddress ::=
OCTET STRING (SIZE (1..21))
-- This data type is used to model NSAP addresses.
-- groups in the CLNS MIB
clnp OBJECT IDENTIFIER ::= { clns 1 }
error OBJECT IDENTIFIER ::= { clns 2 }
echo OBJECT IDENTIFIER ::= { clns 3 }
es-is OBJECT IDENTIFIER ::= { clns 4 }
-- the CLNP group
-- Implementation of this group is recommended for all
-- systems which implement the CLNP.
Satz [Page 4]
RFC 1238 CLNS MIB June 1991
clnpForwarding OBJECT-TYPE
SYNTAX INTEGER {
is(1), -- entity is an intermediate system
-- entity is an end system and does
es(2) -- not forward PDUs
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The indication of whether this entity is active
as an intermediate or end system. Only
intermediate systems will forward PDUs onward that
are not addressed to them."
::= { clnp 1 }
clnpDefaultLifeTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The default value inserted into the Lifetime
field of the CLNP PDU header of PDUs sourced by
this entity."
::= { clnp 2 }
clnpInReceives OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input PDUs received from all
connected network interfaces running CLNP,
including errors."
::= { clnp 3 }
clnpInHdrErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input PDUs discarded due to errors
in the CLNP header, including bad checksums,
version mismatch, lifetime exceeded, errors
discovered in processing options, etc."
::= { clnp 4 }
Satz [Page 5]
RFC 1238 CLNS MIB June 1991
clnpInAddrErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input PDUs discarded because the
NSAP address in the CLNP header's destination
field was not a valid NSAP to be received at this
entity. This count includes addresses not
understood. For end systems, this is a count of
PDUs which arrived with a destination NSAP which
was not local."
::= { clnp 5 }
clnpForwPDUs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input PDUs for which this entity
was not the final destination and which an attempt
was made to forward them onward."
::= { clnp 6 }
clnpInUnknownNLPs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of locally-addressed PDUs successfully
received but discarded because the network layer
protocol was unknown or unsupported (e.g., not
CLNP or ES-IS)."
::= { clnp 7 }
clnpInUnknownULPs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of locally-addressed PDUs successfully
received but discarded because the upper layer
protocol was unknown or unsupported (e.g., not
TP4)."
::= { clnp 8 }
clnpInDiscards OBJECT-TYPE
SYNTAX Counter
Satz [Page 6]
RFC 1238 CLNS MIB June 1991
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input CLNP PDUs for which no
problems were encountered to prevent their
continued processing, but were discarded (e.g.,
for lack of buffer space). Note that this counter
does not include any PDUs discarded while awaiting
re-assembly."
::= { clnp 9 }
clnpInDelivers OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of input PDUs successfully
delivered to the CLNS transport user."
::= { clnp 10 }
clnpOutRequests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of CLNP PDUs which local CLNS
user protocols supplied to CLNP for transmission
requests. This counter does not include any PDUs
counted in clnpForwPDUs."
::= { clnp 11 }
clnpOutDiscards OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of output CLNP PDUs for which no other
problem was encountered to prevent their
transmission but were discarded (e.g., for lack of
buffer space). Note this counter includes PDUs
counted in clnpForwPDUs."
::= { clnp 12 }
clnpOutNoRoutes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Satz [Page 7]
RFC 1238 CLNS MIB June 1991
"The number of CLNP PDUs discarded because no
route could be found to transmit them to their
destination. This counter includes any PDUs
counted in clnpForwPDUs."
::= { clnp 13 }
clnpReasmTimeout OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of seconds which received
segments are held while they are awaiting
reassembly at this entity."
::= { clnp 14 }
clnpReasmReqds OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP segments received which needed
to be reassembled at this entity."
::= { clnp 15 }
clnpReasmOKs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP PDUs successfully re-assembled
at this entity."
::= { clnp 16 }
clnpReasmFails OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of failures detected by the CLNP
reassembly algorithm (for any reason: timed out,
buffer size, etc)."
::= { clnp 17 }
clnpSegOKs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
Satz [Page 8]
RFC 1238 CLNS MIB June 1991
DESCRIPTION
"The number of CLNP PDUs that have been
successfully segmented at this entity."
::= { clnp 18 }
clnpSegFails OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP PDUs that have been discarded
because they needed to be fragmented at this
entity but could not."
::= { clnp 19 }
clnpSegCreates OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP PDU segments that have been
generated as a result of segmentation at this
entity."
::= { clnp 20 }
clnpInOpts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP PDU segments that have been
input with options at this entity."
::= { clnp 25 }
clnpOutOpts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP PDU segments that have been
generated with options by this entity."
::= { clnp 26 }
clnpRoutingDiscards OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Satz [Page 9]
RFC 1238 CLNS MIB June 1991
"The number of routing entries which were chosen
to be discarded even though they are valid. One
possible reason for discarding such an entry could
be to free-up buffer space for other routing
entries."
::= { clnp 27 }
-- the CLNP Interfaces table
-- The CLNP interfaces table contains information on the
-- entity's interfaces which are running the CLNP.
clnpAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpAddrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of addressing information relevant to
this entity's CLNP addresses. "
::= { clnp 21 }
clnpAddrEntry OBJECT-TYPE
SYNTAX ClnpAddrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The addressing information for one of this
entity's CLNP addresses."
INDEX { clnpAdEntAddr }
::= { clnpAddrTable 1 }
ClnpAddrEntry ::=
SEQUENCE {
clnpAdEntAddr
ClnpAddress,
clnpAdEntIfIndex
INTEGER,
clnpAdEntReasmMaxSize
INTEGER (0..65535)
}
clnpAdEntAddr OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The CLNP address to which this entry's addressing
Satz [Page 10]
RFC 1238 CLNS MIB June 1991
information pertains."
::= { clnpAddrEntry 1 }
clnpAdEntIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The index value which uniquely identifies the
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value of ifIndex."
::= { clnpAddrEntry 2 }
clnpAdEntReasmMaxSize OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The size of the largest CLNP PDU which this
entity can re-assemble from incoming CLNP
segmented PDUs received on this interface."
::= { clnpAddrEntry 3 }
-- The CLNP Routing table
-- The CLNP routing table contains an entry for each route
-- known to the entity.
clnpRoutingTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpRouteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This entity's CLNP routing table."
::= { clnp 22 }
clnpRouteEntry OBJECT-TYPE
SYNTAX ClnpRouteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A route to a particular destination."
INDEX { clnpRouteDest }
::= { clnpRoutingTable 1 }
Satz [Page 11]
RFC 1238 CLNS MIB June 1991
ClnpRouteEntry ::=
SEQUENCE {
clnpRouteDest
ClnpAddress,
clnpRouteIfIndex
INTEGER,
clnpRouteMetric1
INTEGER,
clnpRouteMetric2
INTEGER,
clnpRouteMetric3
INTEGER,
clnpRouteMetric4
INTEGER,
clnpRouteNextHop
ClnpAddress,
clnpRouteType
INTEGER,
clnpRouteProto
INTEGER,
clnpRouteAge
INTEGER,
clnpRouteMetric5
INTEGER,
clnpRouteInfo
OBJECT IDENTIFIER
}
clnpRouteDest OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The destination CLNP address of this route."
::= { clnpRouteEntry 1 }
clnpRouteIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The index value which uniquely identifies the
local interface through which the next hop of this
route should be reached. The interface identified
by a particular value of this index is the same as
identified by the same value of ifIndex."
::= { clnpRouteEntry 2 }
Satz [Page 12]
RFC 1238 CLNS MIB June 1991
clnpRouteMetric1 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The primary routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
clnpRouteProto value. If this metric is not used,
its value should be set to -1."
::= { clnpRouteEntry 3 }
clnpRouteMetric2 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
clnpRouteProto value. If this metric is not used,
its value should be set to -1."
::= { clnpRouteEntry 4 }
clnpRouteMetric3 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
clnpRouteProto value. If this metric is not used,
its value should be set to -1."
::= { clnpRouteEntry 5 }
clnpRouteMetric4 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
clnpRouteProto value. If this metric is not used,
its value should be set to -1."
::= { clnpRouteEntry 6 }
Satz [Page 13]
RFC 1238 CLNS MIB June 1991
clnpRouteNextHop OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The CLNP address of the next hop of this route."
::= { clnpRouteEntry 7 }
clnpRouteType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the following
invalid(2), -- an invalidated route
-- route to directly
direct(3), -- connected (sub-)network
-- route to a non-local
remote(4) -- host/network/sub-network
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The type of route.
Setting this object to the value invalid(2) has
the effect of invaliding the corresponding entry
in the clnpRoutingTable. That is, it effectively
dissasociates the destination identified with said
entry from the route identified with said entry.
It is an implementation-specific matter as to
whether the agent removes an invalidated entry
from the table. Accordingly, management stations
must be prepared to receive tabular information
from agents that corresponds to entries not
currently in use. Proper interpretation of such
entries requires examination of the relevant
clnpRouteType object."
::= { clnpRouteEntry 8 }
clnpRouteProto OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the following
-- non-protocol information
-- e.g., manually
local(2), -- configured entries
Satz [Page 14]
RFC 1238 CLNS MIB June 1991
-- set via a network
netmgmt(3), -- management protocol
-- similar to ipRouteProto but
-- omits several IP-specific
-- protocols
is-is(9),
ciscoIgrp(11),
bbnSpfIgp(12),
ospf(13),
bgp(14)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The routing mechanism via which this route was
learned. Inclusion of values for gateway routing
protocols is not intended to imply that hosts
should support those protocols."
::= { clnpRouteEntry 9 }
clnpRouteAge OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of seconds since this route was last
updated or otherwise determined to be correct.
Note that no semantics of `too old' can be implied
except through knowledge of the routing protocol
by which the route was learned."
::= { clnpRouteEntry 10 }
clnpRouteMetric5 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the route's
clnpRouteProto value. If this metric is not used,
its value should be set to -1."
::= { clnpRouteEntry 11 }
clnpRouteInfo OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
Satz [Page 15]
RFC 1238 CLNS MIB June 1991
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A reference to MIB definitions specific to the
particular routing protocol which is responsible
for this route, as determined by the value
specified in the route's clnpRouteProto value. If
this information is not present, its value should
be set to the OBJECT IDENTIFIER { 0 0 }, which is
a syntatically valid object identifier, and any
conformant implementation of ASN.1 and BER must be
able to generate and recognize this value."
::= { clnpRouteEntry 12 }
-- the CLNP Address Translation table
-- The Address Translation tables contain the CLNP address
-- to physical address equivalences. Some interfaces do not
-- use translation tables for determining address
-- equivalences; if all interfaces are of this type, then the
-- Address Translation table is empty, i.e., has zero
-- entries.
clnpNetToMediaTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpNetToMediaEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The CLNP Address Translation table used for
mapping from CLNP addresses to physical
addresses."
::= { clnp 23 }
clnpNetToMediaEntry OBJECT-TYPE
SYNTAX ClnpNetToMediaEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry contains one CLNP address to
`physical' address equivalence."
INDEX { clnpNetToMediaIfIndex, clnpNetToMediaNetAddress }
::= { clnpNetToMediaTable 1 }
ClnpNetToMediaEntry ::=
SEQUENCE {
clnpNetToMediaIfIndex
INTEGER,
Satz [Page 16]
RFC 1238 CLNS MIB June 1991
clnpNetToMediaPhysAddress
PhysAddress,
clnpNetToMediaNetAddress
ClnpAddress,
clnpNetToMediaType
INTEGER,
clnpNetToMediaAge
INTEGER,
clnpNetToMediaHoldTime
INTEGER
}
clnpNetToMediaIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The interface on which this entry's equivalence
is effective. The interface identified by a
particular value of this index is the same
interface as identified by the same value of
ifIndex."
::= { clnpNetToMediaEntry 1 }
clnpNetToMediaPhysAddress OBJECT-TYPE
SYNTAX PhysAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The media-dependent `physical' address."
::= { clnpNetToMediaEntry 2 }
clnpNetToMediaNetAddress OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The CLNP address corresponding to the media-
dependent `physical' address."
::= { clnpNetToMediaEntry 3 }
clnpNetToMediaType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the following
invalid(2), -- an invalidated mapping
dynamic(3),
static(4)
}
Satz [Page 17]
RFC 1238 CLNS MIB June 1991
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The type of mapping.
Setting this object to the value invalid(2) has
the effect of invalidating the corresponding entry
in the clnpNetToMediaTable. That is, it
effectively dissassociates the interface
identified with said entry from the mapping
identified with said entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
Accordingly, management stations must be prepared
to receive tabular information from agents that
corresponds to entries not currently in use.
Proper interpretation of such entries requires
examination of the relevant clnpNetToMediaType
object."
::= { clnpNetToMediaEntry 4 }
clnpNetToMediaAge OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of seconds since this entry was last
updated or otherwise determined to be correct.
Note that no semantics of `too old' can be implied
except through knowledge of the type of entry."
::= { clnpNetToMediaEntry 5 }
clnpNetToMediaHoldTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The time in seconds this entry will be valid.
Static entries should always report this field as
-1."
::= { clnpNetToMediaEntry 6 }
clnpMediaToNetTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClnpMediaToNetEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The CLNP Address Translation table used for
Satz [Page 18]
RFC 1238 CLNS MIB June 1991
mapping from physical addresses to CLNP
addresses."
::= { clnp 24 }
clnpMediaToNetEntry OBJECT-TYPE
SYNTAX ClnpMediaToNetEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry contains on ClnpAddress to `physical'
address equivalence."
INDEX { clnpMediaToNetIfIndex, clnpMediaToNetPhysAddress }
::= { clnpMediaToNetTable 1 }
ClnpMediaToNetEntry ::=
SEQUENCE {
clnpMediaToNetIfIndex
INTEGER,
clnpMediaToNetNetAddress
ClnpAddress,
clnpMediaToNetPhysAddress
PhysAddress,
clnpMediaToNetType
INTEGER,
clnpMediaToNetAge
INTEGER,
clnpMediaToNetHoldTime
INTEGER
}
clnpMediaToNetIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The interface on which this entry's equivalence
is effective. The interface identified by a
particular value of this index is the same
interface as identified by the same value of
ifIndex."
::= { clnpMediaToNetEntry 1 }
clnpMediaToNetAddress OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The ClnpAddress corresponding to the media-
Satz [Page 19]
RFC 1238 CLNS MIB June 1991
dependent `physical' address."
::= { clnpMediaToNetEntry 2 }
clnpMediaToNetPhysAddress OBJECT-TYPE
SYNTAX PhysAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The media-dependent `physical' address."
::= { clnpMediaToNetEntry 3 }
clnpMediaToNetType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- none of the following
invalid(2), -- an invalidated mapping
dynamic(3),
static(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The type of mapping.
Setting this object to the value invalid(2) has
the effect of invalidating the corresponding entry
in the clnpMediaToNetTable. That is, it
effectively dissassociates the interface
identified with said entry from the mapping
identified with said entry. It is an
implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
Accordingly, management stations must be prepared
to receive tabular information from agents that
corresponds to entries not currently in use.
Proper interpretation of such entries requires
examination of the relevant clnpMediaToNetType
object."
::= { clnpMediaToNetEntry 4 }
clnpMediaToNetAge OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of seconds since this entry was last
updated or otherwise determined to be correct.
Note that no semantics of `too old' can be implied
except through knowledge of the type of entry."
Satz [Page 20]
RFC 1238 CLNS MIB June 1991
::= { clnpMediaToNetEntry 5 }
clnpMediaToNetHoldTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The time in seconds this entry will be valid.
Static entries should always report this field as
-1."
::= { clnpMediaToNetEntry 6 }
-- the CLNP Error group
-- Implementation of this group is recommended for all
-- systems which implement the CLNP Error protocol.
clnpInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP Error PDUs received by this
entity."
::= { error 1 }
clnpOutErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of CLNP Error PDUs sent by this
entity."
::= { error 2 }
clnpInErrUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unspecified CLNP Error PDUs
received by this entity."
::= { error 3 }
clnpInErrProcs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
Satz [Page 21]
RFC 1238 CLNS MIB June 1991
STATUS mandatory
DESCRIPTION
"The number of protocol procedure CLNP Error PDUs
received by this entity."
::= { error 4 }
clnpInErrCksums OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of checksum CLNP Error PDUs received
by this entity."
::= { error 5 }
clnpInErrCongests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of congestion drop CLNP Error PDUs
received by this entity."
::= { error 6 }
clnpInErrHdrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of header syntax CLNP Error PDUs
received by this entity."
::= { error 7 }
clnpInErrSegs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of segmentation disallowed CLNP Error
PDUs received by this entity."
::= { error 8 }
clnpInErrIncomps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of incomplete PDU CLNP Error PDUs
Satz [Page 22]
RFC 1238 CLNS MIB June 1991
received by this entity."
::= { error 9 }
clnpInErrDups OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of duplicate option CLNP Error PDUs
received by this entity."
::= { error 10 }
clnpInErrUnreachDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unreachable destination CLNP Error
PDUs received by this entity."
::= { error 11 }
clnpInErrUnknownDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unknown destination CLNP Error PDUs
received by this entity."
::= { error 12 }
clnpInErrSRUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unspecified source route CLNP Error
PDUs received by this entity."
::= { error 13 }
clnpInErrSRSyntaxes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of source route syntax CLNP Error PDUs
received by this entity."
::= { error 14 }
Satz [Page 23]
RFC 1238 CLNS MIB June 1991
clnpInErrSRUnkAddrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of source route unknown address CLNP
Error PDUs received by this entity."
::= { error 15 }
clnpInErrSRBadPaths OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of source route bad path CLNP Error
PDUs received by this entity."
::= { error 16 }
clnpInErrHops OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of hop count exceeded CLNP Error PDUs
received by this entity."
::= { error 17 }
clnpInErrHopReassms OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of hop count exceeded while
reassembling CLNP Error PDUs received by this
entity."
::= { error 18 }
clnpInErrUnsOptions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported option CLNP Error PDUs
received by this entity."
::= { error 19 }
clnpInErrUnsVersions OBJECT-TYPE
SYNTAX Counter
Satz [Page 24]
RFC 1238 CLNS MIB June 1991
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of version mismatch CLNP Error PDUs
received by this entity."
::= { error 20 }
clnpInErrUnsSecurities OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported security option CLNP
Error PDUs received by this entity."
::= { error 21 }
clnpInErrUnsSRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported source route option
CLNP Error PDUs received by this entity."
::= { error 22 }
clnpInErrUnsRRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported record route option
CLNP Error PDUs received by this entity."
::= { error 23 }
clnpInErrInterferences OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of reassembly interference CLNP Error
PDUs received by this entity."
::= { error 24 }
clnpOutErrUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
Satz [Page 25]
RFC 1238 CLNS MIB June 1991
"The number of unspecified CLNP Error PDUs sent by
this entity."
::= { error 25 }
clnpOutErrProcs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of protocol procedure CLNP Error PDUs
sent by this entity."
::= { error 26 }
clnpOutErrCksums OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of checksum CLNP Error PDUs sent by
this entity."
::= { error 27 }
clnpOutErrCongests OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of congestion drop CLNP Error PDUs
sent by this entity."
::= { error 28 }
clnpOutErrHdrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of header syntax CLNP Error PDUs sent
by this entity."
::= { error 29 }
clnpOutErrSegs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of segmentation disallowed CLNP Error
PDUs sent by this entity."
::= { error 30 }
Satz [Page 26]
RFC 1238 CLNS MIB June 1991
clnpOutErrIncomps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of incomplete PDU CLNP Error PDUs sent
by this entity."
::= { error 31 }
clnpOutErrDups OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of duplicate option CLNP Error PDUs
sent by this entity."
::= { error 32 }
clnpOutErrUnreachDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unreachable destination CLNP Error
PDUs sent by this entity."
::= { error 33 }
clnpOutErrUnknownDsts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unknown destination CLNP Error PDUs
sent by this entity."
::= { error 34 }
clnpOutErrSRUnspecs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unspecified source route CLNP Error
PDUs sent by this entity."
::= { error 35 }
clnpOutErrSRSyntaxes OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
Satz [Page 27]
RFC 1238 CLNS MIB June 1991
STATUS mandatory
DESCRIPTION
"The number of source route syntax CLNP Error PDUs
sent by this entity."
::= { error 36 }
clnpOutErrSRUnkAddrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of source route unknown address CLNP
Error PDUs sent by this entity."
::= { error 37 }
clnpOutErrSRBadPaths OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of source route bad path CLNP Error
PDUs sent by this entity."
::= { error 38 }
clnpOutErrHops OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of hop count exceeded CLNP Error PDUs
sent by this entity."
::= { error 39 }
clnpOutErrHopReassms OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of hop count exceeded while
reassembling CLNP Error PDUs sent by this entity."
::= { error 40 }
clnpOutErrUnsOptions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported option CLNP Error PDUs
Satz [Page 28]
RFC 1238 CLNS MIB June 1991
sent by this entity."
::= { error 41 }
clnpOutErrUnsVersions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of version mismatch CLNP Error PDUs
sent by this entity."
::= { error 42 }
clnpOutErrUnsSecurities OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported security option CLNP
Error PDUs sent by this entity."
::= { error 43 }
clnpOutErrUnsSRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported source route option
CLNP Error PDUs sent by this entity."
::= { error 44 }
clnpOutErrUnsRRs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of unsupported record route option
CLNP Error PDUs sent by this entity."
::= { error 45 }
clnpOutErrInterferences OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of reassembly interference CLNP Error
PDUs sent by this entity."
::= { error 46 }
Satz [Page 29]
RFC 1238 CLNS MIB June 1991
-- the ES-IS group
-- Implementation of this group is recommended for all
-- systems which implement the End-System to Intermediate
-- System protocol.
esisESHins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ESH PDUs received by this entity."
::= { es-is 1 }
esisESHouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ESH PDUs sent by this entity."
::= { es-is 2 }
esisISHins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ISH PDUs received by this entity."
::= { es-is 3 }
esisISHouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ISH PDUs sent by this entity."
::= { es-is 4 }
esisRDUins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of RDU PDUs received by this entity."
::= { es-is 5 }
esisRDUouts OBJECT-TYPE
SYNTAX Counter
Satz [Page 30]
RFC 1238 CLNS MIB June 1991
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of RDU PDUs sent by this entity."
::= { es-is 6 }
END
5. References
[1] Cerf, V., "IAB Recommendations for the Development of Internet
Network Management Standards", RFC 1052, IAB, April 1988.
[2] Cerf, V., "Report of the Second Ad Hoc Network Management Review
Group", RFC 1109, NRI, August 1989.
[3] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
Performance Systems International and Hughes LAN Systems, May
1990.
[4] McCloghrie, K., and M. Rose, "Management Information Base for
Network Management of TCP/IP-based Internets", RFC 1156, Hughes
LAN Systems and Performance Systems International, May 1990.
[5] Case, J., M. Fedor, M. Schoffstall, and J. Davin, The Simple
Network Management Protocol", RFC 1157, University of Tennessee
at Knoxville, Performance Systems International, Performance
Systems International, and the MIT Laboratory for Computer
Science, May 1990.
[6] McCloghrie, K., and M. Rose, Editors, "Management Information
Base for Network Management of TCP/IP-based internets", RFC 1213,
Hughes LAN Systems, Inc., Performance Systems International,
March 1991.
[7] Information processing systems - Open Systems Interconnection,
"Specification of Abstract Syntax Notation One (ASN.1)",
International Organization for Standardization, International
Standard 8824, December 1987.
[8] Information processing systems - Open Systems Interconnection,
"Specification of Basic Encoding Rules for Abstract Notation One
(ASN.1)", International Organization for Standardization,
International Standard 8825, December 1987.
[9] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions,
RFC 1212, Performance Systems International, Hughes LAN Systems,
Satz [Page 31]
RFC 1238 CLNS MIB June 1991
Inc., March 1991.
[10] Information processing systems - Data Communications - Protocol
for providing the Connectionless-mode Network Service and
Provision of Underlying Service, International Organization for
Standardization, International Standard 8473, May 1987.
[11] End System to Intermediate System Routing Exchange Protocol for
Use in Conjunction with the Protocol for the Provision of the
Connectionless-mode Network Service (ISO 8473), International
Draft Proposal 9542.
[12] Kille, S., "A String Encoding of Presentation Address", Research
Note RN/89/14, Department of Computer Science, University College
London, February 1989.
6. Security Considerations
Security issues are not discussed in this memo.
7. Author's Address:
Greg Satz
cisco Systems, Inc.
1350 Willow Road
Menlo Park, CA 94025
Phone: (415) 326-1941
Email: Satz@CISCO.COM
Satz [Page 32]