Party MIB for version 2 of the Simple Network Management Protocol (SNMPv2)
RFC 1447
Document | Type | RFC - Historic (April 1993) | |
---|---|---|---|
Authors | James Galvin , Keith McCloghrie | ||
Last updated | 2013-03-02 | ||
RFC stream | Internet Engineering Task Force (IETF) | ||
Formats | |||
Additional resources | snmp-sec-dev-request%40tis.com | ||
IESG | Responsible AD | (None) | |
Send notices to | (None) |
RFC 1447
Network Working Group K. McCloghrie
Request for Comments: 1447 Hughes LAN Systems
J. Galvin
Trusted Information Systems
April 1993
Party MIB
for version 2 of the
Simple Network Management Protocol (SNMPv2)
Status of this Memo
This RFC specifes an IAB standards track protocol for the
Internet community, and requests discussion and suggestions
for improvements. Please refer to the current edition of the
"IAB Official Protocol Standards" for the standardization
state and status of this protocol. Distribution of this memo
is unlimited.
Table of Contents
1 Introduction .......................................... 2
1.1 A Note on Terminology ............................... 2
2 Definitions ........................................... 3
3.1 Textual Conventions ................................. 4
3.2 Administrative Assignments .......................... 7
3.2.1 Initial Party and Context Identifiers ............. 8
3.3 Object Assignments .................................. 16
3.4 The SNMPv2 Party Database Group ..................... 16
3.5 The SNMPv2 Contexts Database Group .................. 29
3.5 The SNMPv2 Access Privileges Database Group ......... 36
3.6 The MIB View Database Group ......................... 40
3.7 Conformance Information ............................. 45
3.7.1 Compliance Statements ............................. 45
3.7.2 Units of Conformance .............................. 47
3 Acknowledgments ....................................... 48
4 References ............................................ 49
5 Security Considerations ............................... 50
6 Authors' Addresses .................................... 50
Galvin & McCloghrie [Page 1]
RFC 1447 Party MIB for SNMPv2 April 1993
1. Introduction
A network management system contains: several (potentially
many) nodes, each with a processing entity, termed an agent,
which has access to management instrumentation; at least one
management station; and, a management protocol, used to convey
management information between the agents and management
stations. Operations of the protocol are carried out under an
administrative framework which defines both authentication and
authorization policies.
Network management stations execute management applications
which monitor and control network elements. Network elements
are devices such as hosts, routers, terminal servers, etc.,
which are monitored and controlled through access to their
management information.
Management information is viewed as a collection of managed
objects, residing in a virtual information store, termed the
Management Information Base (MIB). Collections of related
objects are defined in MIB modules. These modules are written
using a subset of OSI's Abstract Syntax Notation One (ASN.1)
[1], termed the Structure of Management Information (SMI) [2].
The Administrative Model for SNMPv2 document [3] defines the
properties associated with SNMPv2 parties, SNMPv2 contexts,
and access control policies. It is the purpose of this
document, the Party MIB for SNMPv2, to define managed objects
which correspond to these properties.
1.1. A Note on Terminology
For the purpose of exposition, the original Internet-standard
Network Management Framework, as described in RFCs 1155, 1157,
and 1212, is termed the SNMP version 1 framework (SNMPv1).
The current framework is termed the SNMP version 2 framework
(SNMPv2).
Galvin & McCloghrie [Page 2]
RFC 1447 Party MIB for SNMPv2 April 1993
2. Definitions
SNMPv2-PARTY-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, snmpModules,
UInteger32
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, RowStatus, TruthValue
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF;
partyMIB MODULE-IDENTITY
LAST-UPDATED "9304010000Z"
ORGANIZATION "IETF SNMP Security Working Group"
CONTACT-INFO
" Keith McCloghrie
Postal: Hughes LAN Systems
1225 Charleston Road
Mountain View, CA 94043
US
Tel: +1 415 966 7934
Fax: +1 415 960 3738
E-mail: kzm@hls.com"
DESCRIPTION
"The MIB module describing SNMPv2 parties."
::= { snmpModules 3 }
Galvin & McCloghrie [Page 3]
RFC 1447 Party MIB for SNMPv2 April 1993
-- textual conventions
Party ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Denotes a SNMPv2 party identifier.
Note that agents may impose implementation
limitations on the length of OIDs used to identify
Parties. As such, management stations creating
new parties should be aware that using an
excessively long OID may result in the agent
refusing to perform the set operation and instead
returning the appropriate error response, e.g.,
noCreation."
SYNTAX OBJECT IDENTIFIER
TAddress ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Denotes a transport service address.
For snmpUDPDomain, a TAddress is 6 octets long,
the initial 4 octets containing the IP-address in
network-byte order and the last 2 containing the
UDP port in network-byte order. Consult [5] for
further information on snmpUDPDomain."
SYNTAX OCTET STRING
Galvin & McCloghrie [Page 4]
RFC 1447 Party MIB for SNMPv2 April 1993
Clock ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A party's authentication clock - a non-negative
integer which is incremented as specified/allowed
by the party's Authentication Protocol.
For noAuth, a party's authentication clock is
unused and its value is undefined.
For v2md5AuthProtocol, a party's authentication
clock is a relative clock with 1-second
granularity."
SYNTAX UInteger32
Context ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Denotes a SNMPv2 context identifier.
Note that agents may impose implementation
limitations on the length of OIDs used to identify
Contexts. As such, management stations creating new
contexts should be aware that using an excessively
long OID may result in the agent refusing to
perform the set operation and instead returning
the appropriate error response, e.g., noCreation."
SYNTAX OBJECT IDENTIFIER
Galvin & McCloghrie [Page 5]
RFC 1447 Party MIB for SNMPv2 April 1993
StorageType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Describes the memory realization of a conceptual
row. A row which is volatile(2) is lost upon
reboot. A row which is nonVolatile(3) is backed
up by stable storage. A row which is permanent(4)
cannot be changed nor deleted."
SYNTAX INTEGER {
other(1), -- eh?
volatile(2), -- e.g., in RAM
nonVolatile(3), -- e.g., in NVRAM
permanent(4) -- e.g., in ROM
}
Galvin & McCloghrie [Page 6]
RFC 1447 Party MIB for SNMPv2 April 1993
-- administrative assignments
partyAdmin OBJECT IDENTIFIER ::= { partyMIB 1 }
-- definitions of security protocols
partyProtocols OBJECT IDENTIFIER ::= { partyAdmin 1 }
-- the protocol without authentication
noAuth OBJECT IDENTIFIER ::= { partyProtocols 1 }
-- the protocol without privacy
noPriv OBJECT IDENTIFIER ::= { partyProtocols 2 }
-- the DES Privacy Protocol [4]
desPrivProtocol
OBJECT IDENTIFIER ::= { partyProtocols 3 }
-- the MD5 Authentication Protocol [4]
v2md5AuthProtocol
OBJECT IDENTIFIER ::= { partyProtocols 4 }
-- definitions of temporal domains
temporalDomains
OBJECT IDENTIFIER ::= { partyAdmin 2 }
-- this temporal domain refers to management information
-- at the current time
currentTime OBJECT IDENTIFIER ::= { temporalDomains 1 }
-- this temporal domain refers to management information
-- upon the next re-initialization of the managed device
restartTime OBJECT IDENTIFIER ::= { temporalDomains 2 }
-- the temporal domain { cacheTime N } refers to management
-- information that is cached and guaranteed to be at most
-- N seconds old
cacheTime OBJECT IDENTIFIER ::= { temporalDomains 3 }
Galvin & McCloghrie [Page 7]
RFC 1447 Party MIB for SNMPv2 April 1993
-- Definition of Initial Party and Context Identifiers
-- When devices are installed, they need to be configured
-- with an initial set of SNMPv2 parties and contexts. The
-- configuration of SNMPv2 parties and contexts requires (among
-- other things) the assignment of several OBJECT IDENTIFIERs.
-- Any local network administration can obtain the delegated
-- authority necessary to assign its own OBJECT IDENTIFIERs.
-- However, to provide for those administrations who have not
-- obtained the necessary authority, this document allocates a
-- branch of the naming tree for use with the following
-- conventions.
initialPartyId OBJECT IDENTIFIER ::= { partyAdmin 3 }
initialContextId
OBJECT IDENTIFIER ::= { partyAdmin 4 }
-- Note these are identified as "initial" party and context
-- identifiers since these allow secure SNMPv2 communication
-- to proceed, thereby allowing further SNMPv2 parties to be
-- configured through use of the SNMPv2 itself.
-- The following definitions identify a party identifier, and
-- specify the initial values of various object instances
-- indexed by that identifier. In addition, the SNMPv2
-- context, access control policy, and MIB view information
-- assigned, by convention, are identified.
Galvin & McCloghrie [Page 8]
RFC 1447 Party MIB for SNMPv2 April 1993
-- Party Identifiers for use as initial SNMPv2 parties
-- at IP address a.b.c.d
-- Note that for all OBJECT IDENTIFIERs assigned under
-- initialPartyId, the four sub-identifiers immediately
-- following initialPartyId represent the four octets of
-- an IP address. Initial party identifiers for other address
-- families are assigned under a different OBJECT IDENTIFIER,
-- as defined elsewhere.
-- Devices which support SNMPv2 as entities acting in an
-- agent role, and accessed via the snmpUDPDomain transport
-- domain, are required to be configured with the appropriate
-- set of the following as implicit assignments as and when
-- they are configured with an IP address. The appropriate
-- set is all those applicable to the authentication and
-- privacy protocols supported by the device.
Galvin & McCloghrie [Page 9]
RFC 1447 Party MIB for SNMPv2 April 1993
-- a noAuth/noPriv party which executes at the agent
-- partyIdentity = { initialPartyId a b c d 1 }
-- partyIndex = 1
-- partyTDomain = snmpUDPDomain
-- partyTAddress = a.b.c.d, 161
-- partyLocal = true (in agent's database)
-- partyAuthProtocol = noAuth
-- partyAuthClock = 0
-- partyAuthPrivate = ''H (the empty string)
-- partyAuthPublic = ''H (the empty string)
-- partyAuthLifetime = 0
-- partyPrivProtocol = noPriv
-- partyPrivPrivate = ''H (the empty string)
-- partyPrivPublic = ''H (the empty string)
-- a noAuth/noPriv party which executes at a manager
-- partyIdentity = { initialPartyId a b c d 2 }
-- partyIndex = 2
-- partyTDomain = snmpUDPDomain
-- partyTAddress = assigned by local administration
-- partyLocal = false (in agent's database)
-- partyAuthProtocol = noAuth
-- partyAuthClock = 0
-- partyAuthPrivate = ''H (the empty string)
-- partyAuthPublic = ''H (the empty string)
-- partyAuthLifetime = 0
-- partyPrivProtocol = noPriv
-- partyPrivPrivate = ''H (the empty string)
-- partyPrivPublic = ''H (the empty string)
Galvin & McCloghrie [Page 10]
RFC 1447 Party MIB for SNMPv2 April 1993
-- a md5Auth/noPriv party which executes at the agent
-- partyIdentity = { initialPartyId a b c d 3 }
-- partyIndex = 3
-- partyTDomain = snmpUDPDomain
-- partyTAddress = a.b.c.d, 161
-- partyLocal = true (in agent's database)
-- partyAuthProtocol = v2md5AuthProtocol
-- partyAuthClock = 0
-- partyAuthPrivate = assigned by local administration
-- partyAuthPublic = ''H (the empty string)
-- partyAuthLifetime = 300
-- partyPrivProtocol = noPriv
-- partyPrivPrivate = ''H (the empty string)
-- partyPrivPublic = ''H (the empty string)
-- a md5Auth/noPriv party which executes at a manager
-- partyIdentity = { initialPartyId a b c d 4 }
-- partyIndex = 4
-- partyTDomain = snmpUDPDomain
-- partyTAddress = assigned by local administration
-- partyLocal = false (in agent's database)
-- partyAuthProtocol = v2md5AuthProtocol
-- partyAuthClock = 0
-- partyAuthPrivate = assigned by local administration
-- partyAuthPublic = ''H (the empty string)
-- partyAuthLifetime = 300
-- partyPrivProtocol = noPriv
-- partyPrivPrivate = ''H (the empty string)
-- partyPrivPublic = ''H (the empty string)
Galvin & McCloghrie [Page 11]
RFC 1447 Party MIB for SNMPv2 April 1993
-- a md5Auth/desPriv party which executes at the agent
-- partyIdentity = { initialPartyId a b c d 5 }
-- partyIndex = 5
-- partyTDomain = snmpUDPDomain
-- partyTAddress = a.b.c.d, 161
-- partyLocal = true (in agent's database)
-- partyAuthProtocol = v2md5AuthProtocol
-- partyAuthClock = 0
-- partyAuthPrivate = assigned by local administration
-- partyAuthPublic = ''H (the empty string)
-- partyAuthLifetime = 300
-- partyPrivProtocol = desPrivProtocol
-- partyPrivPrivate = assigned by local administration
-- partyPrivPublic = ''H (the empty string)
-- a md5Auth/desPriv party which executes at a manager
-- partyIdentity = { initialPartyId a b c d 6 }
-- partyIndex = 6
-- partyTDomain = snmpUDPDomain
-- partyTAddress = assigned by local administration
-- partyLocal = false (in agent's database)
-- partyAuthProtocol = v2md5AuthProtocol
-- partyAuthClock = 0
-- partyAuthPrivate = assigned by local administration
-- partyAuthPublic = ''H (the empty string)
-- partyAuthLifetime = 300
-- partyPrivProtocol = desPrivProtocol
-- partyPrivPrivate = assigned by local administration
-- partyPrivPublic = ''H (the empty string)
Galvin & McCloghrie [Page 12]
RFC 1447 Party MIB for SNMPv2 April 1993
-- the initial SNMPv2 contexts assigned, by convention, are:
-- contextIdentity = { initialContextId a b c d 1 }
-- contextIndex = 1
-- contextLocal = true (in agent's database)
-- contextViewIndex = 1
-- contextLocalEntity = ''H (the empty string)
-- contextLocalTime = currentTime
-- contextProxyDstParty = { 0 0 }
-- contextProxySrcParty = { 0 0 }
-- contextProxyContext = { 0 0 }
-- contextIdentity = { initialContextId a b c d 2 }
-- contextIndex = 2
-- contextLocal = true (in agent's database)
-- contextViewIndex = 2
-- contextLocalEntity = ''H (the empty string)
-- contextLocalTime = currentTime
-- contextProxyDstParty = { 0 0 }
-- contextProxySrcParty = { 0 0 }
-- contextProxyContext = { 0 0 }
Galvin & McCloghrie [Page 13]
RFC 1447 Party MIB for SNMPv2 April 1993
-- The initial access control policy assigned, by
-- convention, is:
-- aclTarget = 1
-- aclSubject = 2
-- aclResources = 1
-- aclPrivileges = 35 (Get, Get-Next & Get-Bulk)
-- aclTarget = 2
-- aclSubject = 1
-- aclResources = 1
-- aclPrivileges = 132 (Response & SNMPv2-Trap)
-- aclTarget = 3
-- aclSubject = 4
-- aclResources = 2
-- aclPrivileges = 43 (Get, Get-Next, Set & Get-Bulk)
-- aclTarget = 4
-- aclSubject = 3
-- aclResources = 2
-- aclPrivileges = 4 (Response)
-- aclTarget = 5
-- aclSubject = 6
-- aclResources = 2
-- aclPrivileges = 43 (Get, Get-Next, Set & Get-Bulk)
-- aclTarget = 6
-- aclSubject = 5
-- aclResources = 2
-- aclPrivileges = 4 (Response)
-- Note that the initial context and access control
-- information assigned above, by default, to the
-- md5Auth/desPriv parties are identical to those assigned to
-- the md5Auth/noPriv parties. However, each administration
-- may choose to have different authorization policies,
-- depending on whether privacy is used.
Galvin & McCloghrie [Page 14]
RFC 1447 Party MIB for SNMPv2 April 1993
-- The initial MIB views assigned, by convention, are:
-- viewIndex = 1
-- viewSubtree = system
-- viewMask = ''H
-- viewType = included
-- viewIndex = 1
-- viewSubtree = snmpStats
-- viewMask = ''H
-- viewType = included
-- viewIndex = 1
-- viewSubtree = snmpParties
-- viewMask = ''H
-- viewType = included
-- viewIndex = 2
-- viewSubtree = internet
-- viewMask = ''H
-- viewType = included
-- Note that full access to the partyTable, contextTable,
-- aclTable, and viewTable gives a manager the ability to
-- configure any parties with any/all capabilities (the
-- equivalent of "root" access). A lesser manager can be
-- given access only to the partyTable so that it can
-- maintain its own parties, but not increase/decrease
-- their capabilities. Such a lesser manager can also
-- create new parties but they are of no use to it.
Galvin & McCloghrie [Page 15]
RFC 1447 Party MIB for SNMPv2 April 1993
-- object assignments
partyMIBObjects
OBJECT IDENTIFIER ::= { partyMIB 2 }
-- the SNMPv2 party database group
snmpParties OBJECT IDENTIFIER ::= { partyMIBObjects 1 }
partyTable OBJECT-TYPE
SYNTAX SEQUENCE OF PartyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNMPv2 Party database."
::= { snmpParties 1 }
partyEntry OBJECT-TYPE
SYNTAX PartyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Locally held information about a particular
SNMPv2 party."
INDEX { IMPLIED partyIdentity }
::= { partyTable 1 }
Galvin & McCloghrie [Page 16]
RFC 1447 Party MIB for SNMPv2 April 1993
PartyEntry ::=
SEQUENCE {
partyIdentity Party,
partyIndex INTEGER,
partyTDomain OBJECT IDENTIFIER,
partyTAddress TAddress,
partyMaxMessageSize INTEGER,
partyLocal TruthValue,
partyAuthProtocol OBJECT IDENTIFIER,
partyAuthClock Clock,
partyAuthPrivate OCTET STRING,
partyAuthPublic OCTET STRING,
partyAuthLifetime INTEGER,
partyPrivProtocol OBJECT IDENTIFIER,
partyPrivPrivate OCTET STRING,
partyPrivPublic OCTET STRING,
partyCloneFrom Party,
partyStorageType StorageType,
partyStatus RowStatus
}
partyIdentity OBJECT-TYPE
SYNTAX Party
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A party identifier uniquely identifying a
particular SNMPv2 party."
::= { partyEntry 1 }
partyIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A unique value for each SNMPv2 party. The value
for each SNMPv2 party must remain constant at
least from one re-initialization of the entity's
network management system to the next re-
initialization."
::= { partyEntry 2 }
Galvin & McCloghrie [Page 17]
RFC 1447 Party MIB for SNMPv2 April 1993
partyTDomain OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the kind of transport service by which
the party receives network management traffic."
DEFVAL { snmpUDPDomain }
::= { partyEntry 3 }
partyTAddress OBJECT-TYPE
SYNTAX TAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The transport service address by which the party
receives network management traffic, formatted
according to the corresponding value of
partyTDomain. For snmpUDPDomain, partyTAddress is
formatted as a 4-octet IP Address concatenated
with a 2-octet UDP port number."
DEFVAL { '000000000000'H }
::= { partyEntry 4 }
partyMaxMessageSize OBJECT-TYPE
SYNTAX INTEGER (484..65507)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum length in octets of a SNMPv2 message
which this party will accept. For parties which
execute at an agent, the agent initializes this
object to the maximum length supported by the
agent, and does not let the object be set to any
larger value. For parties which do not execute at
the agent, the agent must allow the manager to set
this object to any legal value, even if it is
larger than the agent can generate."
DEFVAL { 484 }
::= { partyEntry 5 }
Galvin & McCloghrie [Page 18]
RFC 1447 Party MIB for SNMPv2 April 1993
partyLocal OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of whether this party executes at
this SNMPv2 entity. If this object has a value of
true(1), then the SNMPv2 entity will listen for
SNMPv2 messages on the partyTAddress associated
with this party. If this object has the value
false(2), then the SNMPv2 entity will not listen
for SNMPv2 messages on the partyTAddress
associated with this party."
DEFVAL { false }
::= { partyEntry 6 }
partyAuthProtocol OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication protocol by which all messages
generated by the party are authenticated as to
origin and integrity. The value noAuth signifies
that messages generated by the party are not
authenticated.
Once an instance of this object is created, its
value can not be changed."
DEFVAL { v2md5AuthProtocol }
::= { partyEntry 7 }
Galvin & McCloghrie [Page 19]
RFC 1447 Party MIB for SNMPv2 April 1993
partyAuthClock OBJECT-TYPE
SYNTAX Clock
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication clock which represents the
local notion of the current time specific to the
party. This value must not be decremented unless
the party's private authentication key is changed
simultaneously."
DEFVAL { 0 }
::= { partyEntry 8 }
Galvin & McCloghrie [Page 20]
RFC 1447 Party MIB for SNMPv2 April 1993
partyAuthPrivate OBJECT-TYPE
SYNTAX OCTET STRING
-- for v2md5AuthProtocol: (SIZE (16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An encoding of the party's private authentication
key which may be needed to support the
authentication protocol. Although the value of
this variable may be altered by a management
operation (e.g., a SNMPv2 Set-Request), its value
can never be retrieved by a management operation:
when read, the value of this variable is the zero
length OCTET STRING.
The private authentication key is NOT directly
represented by the value of this variable, but
rather it is represented according to an encoding.
This encoding is the bitwise exclusive-OR of the
old key with the new key, i.e., of the old private
authentication key (prior to the alteration) with
the new private authentication key (after the
alteration). Thus, when processing a received
protocol Set operation, the new private
authentication key is obtained from the value of
this variable as the result of a bitwise
exclusive-OR of the variable's value and the old
private authentication key. In calculating the
exclusive-OR, if the old key is shorter than the
new key, zero-valued padding is appended to the
old key. If no value for the old key exists, a
zero-length OCTET STRING is used in the
calculation."
DEFVAL { ''H } -- the empty string
::= { partyEntry 9 }
Galvin & McCloghrie [Page 21]
RFC 1447 Party MIB for SNMPv2 April 1993
partyAuthPublic OBJECT-TYPE
SYNTAX OCTET STRING
-- for v2md5AuthProtocol: (SIZE (0..16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A publically-readable value for the party.
Depending on the party's authentication protocol,
this value may be needed to support the party's
authentication protocol. Alternatively, it may be
used by a manager during the procedure for
altering secret information about a party. (For
example, by altering the value of an instance of
this object in the same SNMPv2 Set-Request used to
update an instance of partyAuthPrivate, a
subsequent Get-Request can determine if the Set-
Request was successful in the event that no
response to the Set-Request is received, see [4].)
The length of the value is dependent on the
party's authentication protocol. If not used by
the authentication protocol, it is recommended
that agents support values of any length up to and
including the length of the corresponding
partyAuthPrivate object."
DEFVAL { ''H } -- the empty string
::= { partyEntry 10 }
Galvin & McCloghrie [Page 22]
RFC 1447 Party MIB for SNMPv2 April 1993
partyAuthLifetime OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The lifetime (in units of seconds) which
represents an administrative upper bound on
acceptable delivery delay for protocol messages
generated by the party.
Once an instance of this object is created, its
value can not be changed."
DEFVAL { 300 }
::= { partyEntry 11 }
partyPrivProtocol OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The privacy protocol by which all protocol
messages received by the party are protected from
disclosure. The value noPriv signifies that
messages received by the party are not protected.
Once an instance of this object is created, its
value can not be changed."
DEFVAL { noPriv }
::= { partyEntry 12 }
Galvin & McCloghrie [Page 23]
RFC 1447 Party MIB for SNMPv2 April 1993
partyPrivPrivate OBJECT-TYPE
SYNTAX OCTET STRING
-- for desPrivProtocol: (SIZE (16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An encoding of the party's private encryption key
which may be needed to support the privacy
protocol. Although the value of this variable may
be altered by a management operation (e.g., a
SNMPv2 Set-Request), its value can never be
retrieved by a management operation: when read,
the value of this variable is the zero length
OCTET STRING.
The private encryption key is NOT directly
represented by the value of this variable, but
rather it is represented according to an encoding.
This encoding is the bitwise exclusive-OR of the
old key with the new key, i.e., of the old private
encryption key (prior to the alteration) with the
new private encryption key (after the alteration).
Thus, when processing a received protocol Set
operation, the new private encryption key is
obtained from the value of this variable as the
result of a bitwise exclusive-OR of the variable's
value and the old private encryption key. In
calculating the exclusive-OR, if the old key is
shorter than the new key, zero-valued padding is
appended to the old key. If no value for the old
key exists, a zero-length OCTET STRING is used in
the calculation."
DEFVAL { ''H } -- the empty string
::= { partyEntry 13 }
Galvin & McCloghrie [Page 24]
RFC 1447 Party MIB for SNMPv2 April 1993
partyPrivPublic OBJECT-TYPE
SYNTAX OCTET STRING
-- for desPrivProtocol: (SIZE (0..16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A publically-readable value for the party.
Depending on the party's privacy protocol, this
value may be needed to support the party's privacy
protocol. Alternatively, it may be used by a
manager as a part of its procedure for altering
secret information about a party. (For example,
by altering the value of an instance of this
object in the same SNMPv2 Set-Request used to
update an instance of partyPrivPrivate, a
subsequent Get-Request can determine if the Set-
Request was successful in the event that no
response to the Set-Request is received, see [4].)
The length of the value is dependent on the
party's privacy protocol. If not used by the
privacy protocol, it is recommended that agents
support values of any length up to and including
the length of the corresponding partyPrivPrivate
object."
DEFVAL { ''H } -- the empty string
::= { partyEntry 14 }
Galvin & McCloghrie [Page 25]
RFC 1447 Party MIB for SNMPv2 April 1993
partyCloneFrom OBJECT-TYPE
SYNTAX Party
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The identity of a party to clone authentication
and privacy parameters from. When read, the value
{ 0 0 } is returned.
This value must be written exactly once, when the
associated instance of partyStatus either does not
exist or has the value `notReady'. When written,
the value identifies a party, the cloning party,
whose status column has the value `active'. The
cloning party is used in two ways.
One, if instances of the following objects do not
exist for the party being created, then they are
created with values identical to those of the
corresponding objects for the cloning party:
partyAuthProtocol
partyAuthPublic
partyAuthLifetime
partyPrivProtocol
partyPrivPublic
Two, instances of the following objects are
updated using the corresponding values of the
cloning party:
partyAuthPrivate
partyPrivPrivate
(e.g., the value of the cloning party's instance
of the partyAuthPrivate object is XOR'd with the
value of the partyAuthPrivate instances of the
party being created.)"
::= { partyEntry 15 }
Galvin & McCloghrie [Page 26]
RFC 1447 Party MIB for SNMPv2 April 1993
partyStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
partyTable."
DEFVAL { nonVolatile }
::= { partyEntry 16 }
partyStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row in the
partyTable.
A party is not qualified for activation until
instances of all columns of its partyEntry row
have an appropriate value. In particular:
A value must be written to the Party's
partyCloneFrom object.
If the Party's partyAuthProtocol object has the
value md5AuthProtocol, then the corresponding
instance of partyAuthPrivate must contain a
secret of the appropriate length. Further, at
least one management protocol set operation
updating the value of the party's
partyAuthPrivate object must be successfully
processed, before the partyAuthPrivate column is
considered appropriately configured.
If the Party's partyPrivProtocol object has the
value desPrivProtocol, then the corresponding
instance of partyPrivPrivate must contain a
secret of the appropriate length. Further, at
least one management protocol set operation
updating the value of the party's
partyPrivPrivate object must be successfully
processed, before the partyPrivPrivate column is
considered appropriately configured.
Galvin & McCloghrie [Page 27]
RFC 1447 Party MIB for SNMPv2 April 1993
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the partyStatus column is
`notReady'."
::= { partyEntry 17 }
Galvin & McCloghrie [Page 28]
RFC 1447 Party MIB for SNMPv2 April 1993
-- the SNMPv2 contexts database group
snmpContexts OBJECT IDENTIFIER ::= { partyMIBObjects 2 }
contextTable OBJECT-TYPE
SYNTAX SEQUENCE OF ContextEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNMPv2 Context database."
::= { snmpContexts 1 }
contextEntry OBJECT-TYPE
SYNTAX ContextEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Locally held information about a particular
SNMPv2 context."
INDEX { IMPLIED contextIdentity }
::= { contextTable 1 }
ContextEntry ::=
SEQUENCE {
contextIdentity Context,
contextIndex INTEGER,
contextLocal TruthValue,
contextViewIndex INTEGER,
contextLocalEntity OCTET STRING,
contextLocalTime OBJECT IDENTIFIER,
contextProxyDstParty Party,
contextProxySrcParty Party,
contextProxyContext OBJECT IDENTIFIER,
contextStorageType StorageType,
contextStatus RowStatus
}
Galvin & McCloghrie [Page 29]
RFC 1447 Party MIB for SNMPv2 April 1993
contextIdentity OBJECT-TYPE
SYNTAX Context
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A context identifier uniquely identifying a
particular SNMPv2 context."
::= { contextEntry 1 }
contextIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A unique value for each SNMPv2 context. The
value for each SNMPv2 context must remain constant
at least from one re-initialization of the
entity's network management system to the next
re-initialization."
::= { contextEntry 2 }
contextLocal OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of whether this context is realized
by this SNMPv2 entity."
DEFVAL { true }
::= { contextEntry 3 }
Galvin & McCloghrie [Page 30]
RFC 1447 Party MIB for SNMPv2 April 1993
contextViewIndex OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of an instance of this object is
zero, then this corresponding conceptual row in
the contextTable refers to a SNMPv2 context which
identifies a proxy relationship; the values of the
corresponding instances of the
contextProxyDstParty, contextProxySrcParty, and
contextProxyContext objects provide further
information on the proxy relationship.
Otherwise, if the value of an instance of this
object is greater than zero, then this
corresponding conceptual row in the contextTable
refers to a SNMPv2 context which identifies a MIB
view of a locally accessible entity; the value of
the instance identifies the particular MIB view
which has the same value of viewIndex; and the
value of the corresponding instances of the
contextLocalEntity and contextLocalTime objects
provide further information on the local entity
and its temporal domain."
::= { contextEntry 4 }
Galvin & McCloghrie [Page 31]
RFC 1447 Party MIB for SNMPv2 April 1993
contextLocalEntity OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of the corresponding instance of the
contextViewIndex is greater than zero, then the
value of an instance of this object identifies the
local entity whose management information is in
the SNMPv2 context's MIB view. The empty string
indicates that the MIB view contains the SNMPv2
entity's own local management information;
otherwise, a non-empty string indicates that the
MIB view contains management information of some
other local entity, e.g., 'Repeater1'."
DEFVAL { ''H } -- the empty string
::= { contextEntry 5 }
contextLocalTime OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of the corresponding instance of the
contextViewIndex is greater than zero, then the
value of an instance of this object identifies the
temporal context of the management information in
the MIB view."
DEFVAL { currentTime }
::= { contextEntry 6 }
Galvin & McCloghrie [Page 32]
RFC 1447 Party MIB for SNMPv2 April 1993
contextProxyDstParty OBJECT-TYPE
SYNTAX Party
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of the corresponding instance of the
contextViewIndex is equal to zero, then the value
of an instance of this object identifies a SNMPv2
party which is the proxy destination of a proxy
relationship.
If the value of the corresponding instance of the
contextViewIndex is greater than zero, then the
value of an instance of this object is { 0 0 }."
::= { contextEntry 7 }
contextProxySrcParty OBJECT-TYPE
SYNTAX Party
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of the corresponding instance of the
contextViewIndex is equal to zero, then the value
of an instance of this object identifies a SNMPv2
party which is the proxy source of a proxy
relationship.
Interpretation of an instance of this object
depends upon the value of the transport domain
associated with the SNMPv2 party used as the proxy
destination in this proxy relationship.
If the value of the corresponding instance of the
contextViewIndex is greater than zero, then the
value of an instance of this object is { 0 0 }."
::= { contextEntry 8 }
Galvin & McCloghrie [Page 33]
RFC 1447 Party MIB for SNMPv2 April 1993
contextProxyContext OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of the corresponding instance of the
contextViewIndex is equal to zero, then the value
of an instance of this object identifies the
context of a proxy relationship.
Interpretation of an instance of this object
depends upon the value of the transport domain
associated with the SNMPv2 party used as the proxy
destination in this proxy relationship.
If the value of the corresponding instance of the
contextViewIndex is greater than zero, then the
value of an instance of this object is { 0 0 }."
::= { contextEntry 9 }
contextStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
contextTable."
DEFVAL { nonVolatile }
::= { contextEntry 10 }
Galvin & McCloghrie [Page 34]
RFC 1447 Party MIB for SNMPv2 April 1993
contextStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row in the
contextTable.
A context is not qualified for activation until
instances of all corresponding columns have the
appropriate value. In particular, if the
context's contextViewIndex is greater than zero,
then the viewStatus column of the associated
conceptual row(s) in the viewTable must have the
value `active'. Until instances of all
corresponding columns are appropriately
configured, the value of the corresponding
instance of the contextStatus column is
`notReady'."
::= { contextEntry 11 }
Galvin & McCloghrie [Page 35]
RFC 1447 Party MIB for SNMPv2 April 1993
-- the SNMPv2 access privileges database group
snmpAccess OBJECT IDENTIFIER ::= { partyMIBObjects 3 }
aclTable OBJECT-TYPE
SYNTAX SEQUENCE OF AclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The access privileges database."
::= { snmpAccess 1 }
aclEntry OBJECT-TYPE
SYNTAX AclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The access privileges for a particular subject
SNMPv2 party when asking a particular target
SNMPv2 party to access a particular SNMPv2
context."
INDEX { aclTarget, aclSubject, aclResources }
::= { aclTable 1 }
AclEntry ::=
SEQUENCE {
aclTarget INTEGER,
aclSubject INTEGER,
aclResources INTEGER,
aclPrivileges INTEGER,
aclStorageType StorageType,
aclStatus RowStatus
}
Galvin & McCloghrie [Page 36]
RFC 1447 Party MIB for SNMPv2 April 1993
aclTarget OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of an instance of this object
identifies a SNMPv2 party which is the target of
an access control policy, and has the same value
as the instance of the partyIndex object for that
party."
::= { aclEntry 1 }
aclSubject OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of an instance of this object
identifies a SNMPv2 party which is the subject of
an access control policy, and has the same value
as the instance of the partyIndex object for that
SNMPv2 party."
::= { aclEntry 2 }
aclResources OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of an instance of this object
identifies a SNMPv2 context in an access control
policy, and has the same value as the instance of
the contextIndex object for that SNMPv2 context."
::= { aclEntry 3 }
Galvin & McCloghrie [Page 37]
RFC 1447 Party MIB for SNMPv2 April 1993
aclPrivileges OBJECT-TYPE
SYNTAX INTEGER (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The access privileges which govern what
management operations a particular target party
may perform with respect to a particular SNMPv2
context when requested by a particular subject
party. These privileges are specified as a sum of
values, where each value specifies a SNMPv2 PDU
type by which the subject party may request a
permitted operation. The value for a particular
PDU type is computed as 2 raised to the value of
the ASN.1 context-specific tag for the appropriate
SNMPv2 PDU type. The values (for the tags defined
in [5]) are defined in [3] as:
Get : 1
GetNext : 2
Response : 4
Set : 8
unused : 16
GetBulk : 32
Inform : 64
SNMPv2-Trap : 128
The null set is represented by the value zero."
DEFVAL { 35 } -- Get, Get-Next & Get-Bulk
::= { aclEntry 4 }
aclStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
aclTable."
DEFVAL { nonVolatile }
::= { aclEntry 5 }
Galvin & McCloghrie [Page 38]
RFC 1447 Party MIB for SNMPv2 April 1993
aclStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row in the
aclTable."
::= { aclEntry 6 }
Galvin & McCloghrie [Page 39]
RFC 1447 Party MIB for SNMPv2 April 1993
-- the MIB view database group
snmpViews OBJECT IDENTIFIER ::= { partyMIBObjects 4 }
viewTable OBJECT-TYPE
SYNTAX SEQUENCE OF ViewEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Locally held information about the MIB views
known to this SNMPv2 entity.
Each SNMPv2 context which is locally accessible
has a single MIB view which is defined by two
collections of view subtrees: the included view
subtrees, and the excluded view subtrees. Every
such subtree, both included and excluded, is
defined in this table.
To determine if a particular object instance is in
a particular MIB view, compare the object
instance's OBJECT IDENTIFIER with each of the MIB
view's entries in this table. If none match, then
the object instance is not in the MIB view. If
one or more match, then the object instance is
included in, or excluded from, the MIB view
according to the value of viewType in the entry
whose value of viewSubtree has the most sub-
identifiers. If multiple entries match and have
the same number of sub-identifiers, then the
lexicographically greatest instance of viewType
determines the inclusion or exclusion.
An object instance's OBJECT IDENTIFIER X matches
an entry in this table when the number of sub-
identifiers in X is at least as many as in the
value of viewSubtree for the entry, and each sub-
identifier in the value of viewSubtree matches its
corresponding sub-identifier in X. Two sub-
identifiers match either if the corresponding bit
of viewMask is zero (the 'wild card' value), or if
they are equal.
Due to this 'wild card' capability, we introduce
Galvin & McCloghrie [Page 40]
RFC 1447 Party MIB for SNMPv2 April 1993
the term, a 'family' of view subtrees, to refer to
the set of subtrees defined by a particular
combination of values of viewSubtree and viewMask.
In the case where no 'wild card' is defined in
viewMask, the family of view subtrees reduces to a
single view subtree."
::= { snmpViews 1 }
viewEntry OBJECT-TYPE
SYNTAX ViewEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information on a particular family of view
subtrees included in or excluded from a particular
SNMPv2 context's MIB view.
Implementations must not restrict the number of
families of view subtrees for a given MIB view,
except as dictated by resource constraints on the
overall number of entries in the viewTable."
INDEX { viewIndex, IMPLIED viewSubtree }
::= { viewTable 1 }
ViewEntry ::=
SEQUENCE {
viewIndex INTEGER,
viewSubtree OBJECT IDENTIFIER,
viewMask OCTET STRING,
viewType INTEGER,
viewStorageType StorageType,
viewStatus RowStatus
}
Galvin & McCloghrie [Page 41]
RFC 1447 Party MIB for SNMPv2 April 1993
viewIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique value for each MIB view. The value for
each MIB view must remain constant at least from
one re-initialization of the entity's network
management system to the next re-initialization."
::= { viewEntry 1 }
viewSubtree OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A MIB subtree."
::= { viewEntry 2 }
viewMask OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The bit mask which, in combination with the
corresponding instance of viewSubtree, defines a
family of view subtrees.
Each bit of this bit mask corresponds to a sub-
identifier of viewSubtree, with the most
significant bit of the i-th octet of this octet
string value (extended if necessary, see below)
corresponding to the (8*i - 7)-th sub-identifier,
and the least significant bit of the i-th octet of
this octet string corresponding to the (8*i)-th
sub-identifier, where i is in the range 1 through
16.
Each bit of this bit mask specifies whether or not
the corresponding sub-identifiers must match when
determining if an OBJECT IDENTIFIER is in this
family of view subtrees; a '1' indicates that an
exact match must occur; a '0' indicates 'wild
card', i.e., any sub-identifier value matches.
Galvin & McCloghrie [Page 42]
RFC 1447 Party MIB for SNMPv2 April 1993
Thus, the OBJECT IDENTIFIER X of an object
instance is contained in a family of view subtrees
if the following criteria are met:
for each sub-identifier of the value of
viewSubtree, either:
the i-th bit of viewMask is 0, or
the i-th sub-identifier of X is equal to
the i-th sub-identifier of the value of
viewSubtree.
If the value of this bit mask is M bits long and
there are more than M sub-identifiers in the
corresponding instance of viewSubtree, then the
bit mask is extended with 1's to be the required
length.
Note that when the value of this object is the
zero-length string, this extension rule results in
a mask of all-1's being used (i.e., no 'wild
card'), and the family of view subtrees is the one
view subtree uniquely identified by the
corresponding instance of viewSubtree."
DEFVAL { ''H }
::= { viewEntry 3 }
Galvin & McCloghrie [Page 43]
RFC 1447 Party MIB for SNMPv2 April 1993
viewType OBJECT-TYPE
SYNTAX INTEGER {
included(1),
excluded(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of a particular family of view
subtrees within the particular SNMPv2 context's
MIB view. The value 'included(1)' indicates that
the corresponding instances of viewSubtree and
viewMask define a family of view subtrees included
in the MIB view. The value 'excluded(2)'
indicates that the corresponding instances of
viewSubtree and viewMask define a family of view
subtrees excluded from the MIB view."
DEFVAL { included }
::= { viewEntry 4 }
viewStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row in the
viewTable."
DEFVAL { nonVolatile }
::= { viewEntry 5 }
viewStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row in the
viewTable."
::= { viewEntry 6 }
Galvin & McCloghrie [Page 44]
RFC 1447 Party MIB for SNMPv2 April 1993
-- conformance information
partyMIBConformance
OBJECT IDENTIFIER ::= { partyMIB 3 }
partyMIBCompliances
OBJECT IDENTIFIER ::= { partyMIBConformance 1 }
partyMIBGroups
OBJECT IDENTIFIER ::= { partyMIBConformance 2 }
-- compliance statements
unSecurableCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMPv2 entities
which implement the Party MIB, but do not support
any authentication or privacy protocols (i.e.,
only the noAuth and noPriv protocols are
supported)."
MODULE -- this module
MANDATORY-GROUPS { partyMIBGroup }
::= { partyMIBCompliances 1 }
partyNoPrivacyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMPv2 entities
which implement the Party MIB, and support an
authentication protocol, but do not support any
privacy protocols (i.e., only the noAuth,
v2md5AuthProtocol, and noPriv protocols are
supported)."
MODULE -- this module
MANDATORY-GROUPS { partyMIBGroup }
::= { partyMIBCompliances 2 }
Galvin & McCloghrie [Page 45]
RFC 1447 Party MIB for SNMPv2 April 1993
partyPrivacyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMPv2 entities
which implement the Party MIB, support an
authentication protocol, and support a privacy
protocol ONLY for the purpose of accessing
security parameters.
For all aclTable entries authorizing a subject
and/or target SNMPv2 party whose privacy protocol
is desPrivProtocol, to be used in accessing a
SNMPv2 context, the MIB view for that SNMPv2
context shall include only those objects
subordinate to partyMIBObjects, or a subset
thereof, e.g.,
viewSubtree = { partyMIBObjects }
viewMask = ''H
viewType = { included }
Any attempt to configure an entry in the
partyTable, the contextTable, the aclTable or the
viewTable such that a party using the
desPrivProtocol would be authorized for use in
accessing objects outside of the partyMIBObjects
subtree shall result in the appropriate error
response (e.g., wrongValue or inconsistentValue)."
MODULE -- this module
MANDATORY-GROUPS { partyMIBGroup }
::= { partyMIBCompliances 3 }
Galvin & McCloghrie [Page 46]
RFC 1447 Party MIB for SNMPv2 April 1993
fullPrivacyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMPv2 entities
which implement the Party MIB, support an
authentication protocol, and support a privacy
protocol without restrictions on its use."
MODULE -- this module
MANDATORY-GROUPS { partyMIBGroup }
::= { partyMIBCompliances 4 }
-- units of conformance
partyMIBGroup OBJECT-GROUP
OBJECTS { partyIndex, partyTDomain, partyTAddress,
partyMaxMessageSize, partyLocal,
partyAuthProtocol, partyAuthClock,
partyAuthPrivate, partyAuthPublic,
partyAuthLifetime, partyPrivProtocol,
partyPrivPrivate, partyPrivPublic,
partyStorageType, partyStatus,
partyCloneFrom,
contextIndex, contextLocal,
contextViewIndex, contextLocalEntity,
contextLocalTime, contextStorageType,
contextStatus, aclTarget, aclSubject,
aclPrivileges, aclStorageType, aclStatus,
viewMask, viewType, viewStorageType, viewStatus }
STATUS current
DESCRIPTION
"The collection of objects allowing the
description and configuration of SNMPv2 parties.
Note that objects which support proxy
relationships are not included in this conformance
group."
::= { partyMIBGroups 1 }
END
Galvin & McCloghrie [Page 47]
RFC 1447 Party MIB for SNMPv2 April 1993
3. Acknowledgments
This document is based, almost entirely, on RFC 1353.
Galvin & McCloghrie [Page 48]
RFC 1447 Party MIB for SNMPv2 April 1993
4. References
[1] Information processing systems - Open Systems
Interconnection - Specification of Abstract Syntax
Notation One (ASN.1), International Organization for
Standardization. International Standard 8824, (December,
1987).
[2] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S.,
"Structure of Management Information for version 2 of the
Simple Network Management Protocol (SNMPv2)", RFC 1442,
SNMP Research, Inc., Hughes LAN Systems, Dover Beach
Consulting, Inc., Carnegie Mellon University, April 1993.
[3] Galvin, J., and McCloghrie, K., "Administrative Model for
version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1445, Trusted Information Systems, Hughes
LAN Systems, April 1993.
[4] Galvin, J., and McCloghrie, K., "Security Protocols for
version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1446, Trusted Information Systems, Hughes
LAN Systems, April 1993.
[5] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S.,
"Protocol Operations for version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1448, SNMP Research,
Inc., Hughes LAN Systems, Dover Beach Consulting, Inc.,
Carnegie Mellon University, April 1993.
[5] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S.,
"Transport Mappings for version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1449, SNMP Research,
Inc., Hughes LAN Systems, Dover Beach Consulting, Inc.,
Carnegie Mellon University, April 1993.
Galvin & McCloghrie [Page 49]
RFC 1447 Party MIB for SNMPv2 April 1993
5. Security Considerations
Security issues are not discussed in this memo.
6. Authors' Addresses
Keith McCloghrie
Hughes LAN Systems
1225 Charleston Road
Mountain View, CA 94043
US
Phone: +1 415 966 7934
Email: kzm@hls.com
James M. Galvin
Trusted Information Systems, Inc.
3060 Washington Road, Route 97
Glenwood, MD 21738
Phone: +1 301 854-6889
EMail: galvin@tis.com
Galvin & McCloghrie [Page 50]