The SatLabs Group DVB-RCS MIB
RFC 5728
| Document | Type |
RFC - Informational
(March 2010; Errata)
Was draft-combes-ipdvb-mib-rcs (individual in int area)
|
|
|---|---|---|---|
| Authors | Hans-Peter Lexow , Micheline Lambert , Petter Amundsen , Stephane Combes | ||
| Last updated | 2020-01-21 | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text html pdf htmlized with errata bibtex | ||
| Stream | WG state | (None) | |
| Document shepherd | No shepherd assigned | ||
| IESG | IESG state | RFC 5728 (Informational) | |
| Action Holders |
(None)
|
||
| Consensus Boilerplate | Unknown | ||
| Telechat date | |||
| Responsible AD | Jari Arkko | ||
| Send notices to | hlexow@stmi.com | ||
Internet Engineering Task Force (IETF) S. Combes
Request for Comments: 5728 P. Amundsen
Category: Informational M. Lambert
ISSN: 2070-1721 H. Lexow
SatLabs Group
March 2010
The SatLabs Group DVB-RCS MIB
Abstract
This document describes the MIB module for the Digital Video
Broadcasting Return Channel via Satellite system (DVB-RCS), as
defined by the SatLabs Group. It defines a set of MIB objects to
characterize the behavior and performance of network-layer entities
deploying DVB-RCS.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc5728.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Combes, et al. Informational [Page 1]
RFC 5728 DVB-RCS MIB March 2010
This document may not be modified, and derivative works of it may not
be created, except to format it for publication as an RFC or to
translate it into languages other than English.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Table of Contents
1. Introduction ....................................................4
2. Conventions Used in This Document ...............................5
2.1. Abbreviations ..............................................6
2.2. Glossary ...................................................8
2.2.1. Star DVB-RCS Network ................................8
2.2.2. Mesh DVB-RCS Network ................................8
2.2.3. Transparent DVB-RCS Network .........................8
2.2.4. Regenerative DVB-RCS Network ........................8
2.2.5. DVB-RCS MAC Layer ...................................9
2.2.6. DVB-RCS TDM .........................................9
2.2.7. DVB-RCS TDMA ........................................9
2.2.8. IDU .................................................9
2.2.9. ODU .................................................9
2.2.10. RCST ...............................................9
2.2.11. NCC ................................................9
2.2.12. Configuration File ................................10
2.2.13. Log File ..........................................10
2.2.14. Installation Log File .............................10
2.2.15. Antenna Alignment .................................10
2.2.16. CW Frequency ......................................10
2.2.17. Request Class .....................................10
2.2.18. Channel ID ........................................10
2.2.19. ATM Profile .......................................10
2.2.20. MPEG Profile ......................................11
2.2.21. PID Pool ..........................................11
2.2.22. Capacity Categories ...............................11
2.2.23. Start Transponder .................................12
2.2.24. DVB-S .............................................12
2.2.25. DVB-S2 and CCM/VCM/ACM ............................12
2.2.26. Interactive Network ...............................13
Combes, et al. Informational [Page 2]
RFC 5728 DVB-RCS MIB March 2010
3. MIB Module Overview ............................................13
3.1. Textual Conventions .......................................13
3.2. Structure of the MIB ......................................14
3.3. Relationship to the Interfaces MIB Module .................15
3.4. MIB Groups Description ....................................18
3.4.1. dvbRcsRcstSystem ...................................18
3.4.2. dvbRcsRcstNetwork ..................................19
3.4.3. dvbRcsRcstInstall ..................................19
3.4.4. dvbRcsRcstQos ......................................19
3.4.5. dvbRcsRcstControl ..................................20
3.4.6. dvbRcsRcstState ....................................20
3.4.7. dvbRcsFwdLink (dvbRcsFwdConfig and
dvbRcsFwdStatus groups) ............................20
3.4.8. dvbRcsRtnLink (dvbRcsRtnConfig and
dvbRcsRtnStatus groups) ............................20
4. Definitions ....................................................21
5. Security Considerations ........................................91
6. IANA Considerations ............................................92
7. Acknowledgments ................................................92
8. References .....................................................93
8.1. Normative References ......................................93
8.2. Informative References ....................................94
Combes, et al. Informational [Page 3]
RFC 5728 DVB-RCS MIB March 2010
1. Introduction
The SatLabs Group [SATLABS] is an international non-profit EEIG
(European Economic Interest Grouping) committed to large-scale
adoption and deployment of the Digital Video Broadcasting Return
Channel via Satellite (DVB-RCS) standard [ETSI-RCS]. SatLabs members
are service providers, satellite operators, system integrators,
terminal manufacturers, and technology providers with an interest in
DVB-RCS.
Since its creation in 2001, the main goal of the SatLabs Group has
been to achieve interoperability between DVB-RCS terminals and
systems. Therefore, the Group has defined the SatLabs Qualification
Program, which provides an independent certification process for DVB-
RCS terminals based on System Recommendations defined by SatLabs. To
enhance product interoperability, beyond the physical-layer and MAC-
layer mechanisms defined in the DVB-RCS standard, SatLabs has
expanded its Recommendations in the field of DVB-RCS terminal
management [SATLABS]. As part of this effort, SatLabs has specified
a common Simple Network Management Protocol (SNMP) Management
Information Base (MIB) for DVB-RCS terminals, which is defined in
this document.
A DVB-RCS terminal is denoted as a Return Channel Satellite Terminal
(RCST) in the remainder of this document. This consists of an Indoor
Unit (IDU) and an Outdoor Unit (ODU) connected through an Inter-
Facility Link (IFL), usually a coaxial L-band interface. On the user
side, the IDU is connected to the user network through a Local Area
Network (LAN) interface (usually Ethernet). On the network side, the
ODU is connected via a satellite link (the air interface).
The SatLabs Group DVB-RCS MIB is implemented in the IDU of an RCST.
RCST management can be performed either through the LAN interface
(local management) or through the air interface (remote management
from the Network Control Center, NCC). RCST and NCC elements are
shown on Figure 1.
Combes, et al. Informational [Page 4]
RFC 5728 DVB-RCS MIB March 2010
+------------+
| IP |
| End Host |
+-----+------+
|
- - - - - - - -|- - - - - - - - - - - - - - - -
| | LAN interface |
|
| +------+--------+ |
| Indoor Unit |
| | (IDU) | |
+------+--------+
| | |
Inter Facility Link (IFL)
| | |
+-----+---------+
| | Outdoor Unit | |
| (ODU) |
| +------+--------+ |
|
| | Air interface |
- - - - - - - |- - - - - - - - - - - - - - - -
RCST |
| +----------------+
+------->| Network Control|
| Center (NCC) |
+----------------+
Figure 1: RCST Architecture
2. Conventions Used in This Document
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
Combes, et al. Informational [Page 5]
RFC 5728 DVB-RCS MIB March 2010
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119
[RFC2119].
2.1. Abbreviations
AAL5 ATM Adaptation Layer Type 5
ACM Adaptive Coding and Modulation
ATM Asynchronous Transfer Mode
AVBDC Absolute Volume-Based Dynamic Capacity
BER Bit Error Rate
BUC Block Up-Converter
CCM Constant Coding and Modulation
CNR Carrier to Noise Ratio
CRA Continuous Rate Assignment
CSC Common Signaling Channel
CW Continuous Wave (carrier frequency)
dBi deciBel (isotropic)
dBm deciBel (with respect to 1 mW)
DC Direct Current
DSCP Diffserv Code Point
DVB Digital Video Broadcasting
EIRP Equivalent Isotropic Radiated Power
ETSI European Telecommunications Standards Institute
FEC Forward Error Correction
FTP File Transfer Protocol
GS Generic Stream
Combes, et al. Informational [Page 6]
RFC 5728 DVB-RCS MIB March 2010
GSE Generic Stream Encapsulation
IDU Indoor Unit
IFL Inter-Facility Link
LNB Low Noise Block
LO Local Oscillator
MAC Medium Access Control
MIB Management Information Base
MPEG Motion Pictures Expert Group
MPE Multi-Protocol Encapsulation
NCC Network Control Centre
OAM Operations and Management
ODU Outdoor Unit
PHB Per-Hop Behavior
PEP Performance Enhancing Proxy
PID Packet IDentifier (MPEG, used as Elementary Stream Identifier)
QoS Quality of Service
RBDC Rate-Based Dynamic Capacity
RC Request Class
RCS Return Channel via Satellite
RCST Return Channel via Satellite Terminal (DVB-RCS Terminal)
Rx Receive
SDU Service Data Unit
SSPA Solid State Power Amplifier
TDM Time-Division Multiplex
Combes, et al. Informational [Page 7]
RFC 5728 DVB-RCS MIB March 2010
TDMA Time-Division Multiple Access
TFTP Trivial File Transfer Protocol
TS Transport Stream (as defined by MPEG)
Tx Transmit
VBDC Volume-Based Dynamic Capacity
VCI Virtual Channel Identifier (ATM)
VPI Virtual Path Identifier (ATM)
Vpp Volts peak-to-peak
2.2. Glossary
The terms in this document are derived either from DVB-RCS standard
specifications [ETSI-RCS] or from SatLabs System Recommendations
[SATLABS].
2.2.1. Star DVB-RCS Network
This denotes a hub-and-spoke configuration where all communications
pass through a central hub, which usually also includes the NCC.
Peer-to-peer communication between RCSTs is possible through a double
satellite hop (this traffic has to pass through the hub).
2.2.2. Mesh DVB-RCS Network
This denotes a mesh configuration that supports peer-to-peer
communications in a single satellite hop directly between RCSTs.
2.2.3. Transparent DVB-RCS Network
This denotes a network using transparent satellite transponders.
Star or mesh network configurations can be supported. In the case of
a mesh configuration, RCSTs need to incorporate a TDMA receiver in
addition to the TDM receiver.
2.2.4. Regenerative DVB-RCS Network
This denotes a network that uses regenerative satellite transponders,
i.e. includes some On-Board Processing functionality, which allows
demodulation and decoding of the uplink TDMA signals and re-multiplex
of the traffic into TDM signals on the downlink. Star or mesh
network configurations can be supported.
Combes, et al. Informational [Page 8]
RFC 5728 DVB-RCS MIB March 2010
2.2.5. DVB-RCS MAC Layer
The DVB-RCS MAC layer represents the air interface of an RCST, as
specified in [ETSI-RCS]. The interface is bi-directional and
supports IP traffic over hub-spoke (star) and mesh satellite network
topologies.
2.2.6. DVB-RCS TDM
The DVB-RCS TDM corresponds to the forward link of a DVB-RCS
transparent system or the downlink of a DVB-RCS regenerative system.
It is based on either the DVB-S or DVB-S2 standard, specified in
[ETSI-DVBS] and [ETSI-DVBS2] respectively. In the DVB-RCS context,
this interface is uni- or bi-directional, as it may also be used for
a return channel dedicated to a single terminal.
2.2.7. DVB-RCS TDMA
The DVB-RCS TDMA corresponds to the return or mesh link of an RCS
transparent system or the uplink of an RCS regenerative system. It
is specified in [ETSI-RCS].
In the context of star transparent and mesh regenerative DVB-RCS
systems, this interface is uni-directional.
In the context of mesh transparent DVB-RCS systems, this interface is
bi-directional.
2.2.8. IDU
This is the indoor part of the RCST (including at least the power
supply, and usually also the modem and networking functions).
2.2.9. ODU
This is the outdoor part of the RCST (including at least the aerial,
and usually also the LNB and BUC).
2.2.10. RCST
This is the Satellite Terminal, installed on the customer premises.
It is composed of the IDU and ODU.
2.2.11. NCC
The NCC provides Control and Monitoring Functions. It generates
control and timing signals for the operation of the DVB-RCS Network.
Combes, et al. Informational [Page 9]
RFC 5728 DVB-RCS MIB March 2010
2.2.12. Configuration File
The configuration file is an XML-formatted file, storing
configuration parameters for the RCST and their values.
2.2.13. Log File
The log file is stored at the RCST. This is used to log particular
events that occur on the RCST side.
2.2.14. Installation Log File
The installation log file is stored at the RCST. This logs
particular events that occur on the RCST side and are related to RCST
installation phase.
2.2.15. Antenna Alignment
This is the process to align the RCST antenna, part of the ODU, in
order to enable bi-directional communication (uplink, downlink) with
the satellite network.
2.2.16. CW Frequency
The CW frequency is the frequency of a Continuous Wave signal. It is
a narrowband carrier transmitted for the duration of measurements
during the installation of an RCST.
2.2.17. Request Class
A Request Class (RC) is a representation of a Per-Hop Behavior (PHB)
at the MAC layer. It defines a behavior of the MAC layer for a given
aggregation of traffic. This behavior includes a combination of
Capacity Categories associated to the RC and a priority with respect
to the other RCs supported by an RCST.
2.2.18. Channel ID
Each Request Class is identified by a unique Channel_ID in the
communication between the RCST and the NCC.
2.2.19. ATM Profile
The ATM profile is one of the two profiles for traffic burst format
on a DVB-RCS TDMA. It is based on one or more concatenated ATM
cells, each of length 53 bytes, plus an optional prefix.
Combes, et al. Informational [Page 10]
RFC 5728 DVB-RCS MIB March 2010
2.2.20. MPEG Profile
The MPEG profile is one of the two profiles for traffic burst format
on the DVB-RCS TDMA. It is based on a number of concatenated
MPEG2-TS packets, each of length 188 bytes.
2.2.21. PID Pool
For the MPEG profile, several RCs may be mapped within a pool of
several PIDs to allow cross-RC Section Packing [ETSI-DAT]. Section
Packing can be used on all PIDs and higher priority traffic can
always preempt lower priority streams. This reduces the need for
padding.
2.2.22. Capacity Categories
The TDMA timeslot allocation process for the DVB-RCS uplink supports
several Capacity Categories.
The Capacity Categories CRA, RBDC, and A/VBDC, when authorized for an
RC, have to be configured from the NCC. Their configuration
parameters are used to inform the RCST of the configuration of each
category at the NCC side and thus help in Capacity Requests
computation.
The categories are treated independently for each RC. A SatLabs
optional feature is defined that allows their configuration at the
RCST level in addition to configuration per RC. This feature is
denoted RCST_PARA.
2.2.22.1. Continuous Rate Assignment (CRA)
CRA is a rate capacity that is provided in full in a continuous
manner to the RCST while required.
2.2.22.2. Rate-Based Dynamic Capacity (RBDC)
RBDC is a rate capacity that is requested dynamically by an RCST.
RBDC is provided in response to explicit requests from the RCST to
the NCC, such requests being absolute (i.e., corresponding to the
full rate currently being requested). Each request overrides all
previous RBDC requests from the same RCST and is subject to a maximum
rate limit.
Combes, et al. Informational [Page 11]
RFC 5728 DVB-RCS MIB March 2010
2.2.22.3. Volume-Based Dynamic Capacity (VBDC)
VBDC is a volume capacity that is requested dynamically by an RCST.
VBDC is provided in response to explicit requests from the RCST to
the NCC, such requests being cumulative (i.e., each request adds to
all previous requests from the same RCST).
2.2.22.4. Absolute Volume-Based Dynamic Capacity (AVBDC)
AVBDC is a volume capacity that is requested dynamically by an RCST.
This capacity is provided in response to explicit requests from the
RCST to the NCC, such requests being absolute (i.e., this request
replaces the previous ones from the same RCST).
The combination of AVBDC and VBDC is seen as a single Capacity
Category, denoted A/VBDC.
2.2.22.5. Population ID
This defines a group of RCSTs within a network.
2.2.23. Start Transponder
This is the satellite transponder on which the communication is
initiated from an RCST point of view when in the installation mode.
The parameters corresponding to this transponder (satellite orbital
position, frequency, etc.) are stored at the RCST as power-up
configuration data.
2.2.24. DVB-S
DVB-S is the Digital Video Broadcast over Satellite [ETSI-DVBS]. It
is a framework and set of associated standards published by ETSI for
the transmission of video, audio, and data, using the ISO MPEG-2
standard [ISO-MPEG], over satellite links.
2.2.25. DVB-S2 and CCM/VCM/ACM
DVB-S2 is the Second Generation of the Digital Video Broadcast for
Satellite applications standard [ETSI-DVBS2]. It is a framework and
set of associated standards published by ETSI for the transmission of
video, audio, and data.
BBFRAME: The main framing unit of the DVB-S2 protocol stack.
CCM: In CCM transmission mode, the forward link uses a constant set
of transmission parameters (FEC coding rate and modulation
scheme) for all receivers.
Combes, et al. Informational [Page 12]
RFC 5728 DVB-RCS MIB March 2010
VCM: In VCM transmission mode, the forward link uses transmission
parameters that are variable on a BBFRAME-by-BBFRAME but fixed
on a Receiver basis, according to fixed link and propagation
conditions for each Receiver.
ACM: In ACM transmission mode, the forward link uses transmission
parameters that are dynamically adjusted on a BBFRAME-by-BBFRAME
and Receiver-per-Receiver basis, according to actual link and
propagation conditions. In order to implement ACM, feedback
from each Receiver has to be provided by DVB-RCS return channel.
2.2.26. Interactive Network
This is another name for a DVB-RCS-based satellite network.
3. MIB Module Overview
This MIB module provides a set of objects required for the management
of a SatLabs-compliant RCST. The specification is derived from the
parameters and protocols described in [SATLABS].
The MIB module in this document uses the following OBJECT IDENTIFIER
values, as already assigned by IANA under the smi-numbers registry
[IANA]:
+------------+---------------------------+
| Descriptor | OBJECT IDENTIFIER value |
+------------+---------------------------+
|dvbRcsMib |{ mib-2 transmission 239 } |
+------------+---------------------------+
Table 1: Object Identifiers for the MIB
These values have been assigned for this MIB under the
'mib-2.transmission' subtree.
3.1. Textual Conventions
This MIB module defines new textual conventions for RCST indications
of SatLabs-defined capabilities, including profiles, options, and
optional features.
DvbRcsSystemSatLabsProfileMap represents the SatLabs profiles
supported as defined in [SATLABS].
DvbRcsSystemSatLabsOptionMap represents the SatLabs options supported
as defined in [SATLABS]. These are options that are used for the
certification of SatLabs terminals. They represent important
Combes, et al. Informational [Page 13]
RFC 5728 DVB-RCS MIB March 2010
functionality, with impact on interoperability, and their support is
advertised with the RCST certification level.
DvbRcsSystemSatLabsFeatureMap represents the SatLabs optional
features supported as defined in [SATLABS]. These represent minor
features, not necessary for interoperability. They are not used for
the certification of SatLabs terminals.
3.2. Structure of the MIB
This MIB module is structured into two top-level groups:
o The dvbRcsMibObjects group includes all the managed objects of the
DVB-RCS MIB.
o The dvbRcsConformance group includes the compliance statements for
DVB-RCS terminals that are compliant with [SATLABS]. The managed
objects are grouped into formal object groups (i.e., units of
conformance) according to their relation to specific SatLabs
options or features. The conformance statements (MODULE-
COMPLIANCE specification) are described within the
dvbRcsRcstCompliances group, while the units of conformance are
described within the dvbRcsRcstGroups group.
The dvbRcsMibObjects group is further structured into three groups:
dvbRcsRcst, dvbRcsFwdLink, and dvbRcsRtnLink.
The dvbRcsRcst group covers management related to the RCST equipment.
It is structured into six groups:
o dvbRcsRcstSystem
o dvbRcsRcstNetwork
o dvbRcsRcstInstall
o dvbRcsRcstQos
o dvbRcsRcstControl
o dvbRcsRcstState
The dvbRcsFwdLink group covers management information related to the
RCST forward link. It is structured into two groups:
o dvbRcsFwdConfig
o dvbRcsFwdStatus
Combes, et al. Informational [Page 14]
RFC 5728 DVB-RCS MIB March 2010
The dvbRcsRtnLink group covers management information related to the
RCST return link. It is structured into two groups:
o dvbRcsRtnConfig
o dvbRcsRtnStatus
Tables within each of these groups cover different functions like
return link traffic management (packet classes, Request Classes, PID
pools) and forward link configuration and status.
Rows created automatically (e.g., by the device according to the
hardware configuration) may, and generally will, have a mixture of
configuration and status objects within them. Rows that are meant to
be created by the management station are generally restricted to
configuration (read-create) objects.
3.3. Relationship to the Interfaces MIB Module
This section clarifies the relationship of this MIB module to the
Interfaces MIB [RFC2863]. Several areas of correlation are addressed
in the following. The implementer is referred to the Interfaces MIB
document in order to understand the general intent of these areas.
IANA has assigned three ifType labels for DVB-RCS. Each RCST MUST
support at least the three following interfaces:
o dvbRcsMacLayer (239), -- DVB-RCS MAC Layer
DVB-RCS MAC Layer represents the complete air interface of an
RCST, as specified in [ETSI-RCS]. This interface supports star
and mesh networks and is bi-directional. Only star networks are
considered by the present MIB module.
o dvbTdm (240), -- DVB Satellite TDM
DVB-RCS physical link based on Time-Division Multiplexing. It
corresponds to the forward link of an RCS transparent system or
the downlink of an RCS regenerative system. It is based on either
the DVB-S or DVB-S2 standard, specified in [ETSI-DVBS] and
[ETSI-DVBS2] respectively. Only transparent systems are
considered by the present MIB module.
In the DVB-RCS context, this interface is uni- or bi-directional.
In the present MIB module, only a uni-directional (i.e., forward
link, or downstream) dvbTdm interface is considered.
Combes, et al. Informational [Page 15]
RFC 5728 DVB-RCS MIB March 2010
o dvbRcsTdma (241), -- DVB-RCS TDMA
DVB-RCS physical link based on Time-Division Multiple Access. It
corresponds to the return or mesh link of an RCS transparent
system or the uplink of an RCS regenerative system. It is based
on the DVB-RCS standard specified in [ETSI-RCS].
In the context of star transparent and mesh regenerative DVB-RCS
systems, this interface is uni-directional.
In the context of mesh transparent DVB-RCS systems, this interface
is bi-directional.
Only star transparent systems are considered by the present MIB
module (i.e., return link, or upstream).
The protocol stack (as reflected in ifStackTable) will be as follows:
+--------------------------+
| IP |
+--------------------------+
| dvbRcsMacLayer |
+---------------+----------+
| dvbRcsTdma | dvbTdm |
+---------------+----------+
| MPEG/ATM | MPEG/GS |
+---------------+----------+
Figure 2: RCST Protocol Stack
An additional Ethernet interface is used on the LAN side of the RCST
(see Figure 1).
An instance of ifEntry exists for each dvbTdm interface, for each
dvbRcsTdma (normally only one), and for each dvbRcsMac layer
(normally only one).
The interface counters relate to:
o dvbRcsMacLayer: DVB-RCS two-way MAC interface that counts
aggregate Multi-Protocol Encapsulation (MPE) frames, Generic
Stream Encapsulation (GSE) encapsulated PDUs (equals IP packets),
and ATM Adaptation Layer 5 (AAL5) frames.
MPE is specified in [ETSI-DAT] and is transported over MPEG, which is
specified in [ISO-MPEG]. MPEG is transported over GS or TS
(Transport Stream) carriers. The TS carrier is specified in
[ETSI-DVBS] for DVB-S and [ETSI-DVBS2] for DVB-S2.
Combes, et al. Informational [Page 16]
RFC 5728 DVB-RCS MIB March 2010
GSE is specified in [ETSI-GSE] and is transported over the GS
(Generic Stream) carrier, which is specified in [ETSI-DVBS2].
ATM is specified in [ITU-ATM].
AAL5 is specified in [ITU-AAL5].
o dvbTdm: The DVB-RCS TDM interface that counts MPEG TS packets at
stream level, if the TS format is used. If the Generic Stream
(GS) format is used, it counts GSE packets.
o dvbRcsTdma: The DVB-RCS TDMA interface that counts aggregate ATM
and MPEG TS packets.
The ifStackTable [RFC2863] MUST be implemented to identify the
relationships among sub-interfaces.
The following example is a DVB-RCS star network with DVB-S and DVB-
RCS. As illustrated on Figure 3, it shows a DVB-RCS MAC interface
with one downstream and one upstream interface. In this network, ATM
encapsulation is used in the DVB-RCS uplink. Two ATM Logical Ports
are shown. DVB-S2 or DVB-S can be used in the downlink.
ifType 214 'mpegTransport' can also be used for counting TS packets
and bytes for sub-interfaces of dvbRcsTdma or dvbTdm, e.g., per PID-
oriented or per TS-oriented, as desired and applicable.
+----------------------------------------------------------+
| IP Network Layer |
+------+----------------------------------+----------------+
| |
+------+-------+ +------------------+----------------+
| Ethernet LAN | | dvbRcsMacLayer |
+--------------+ +-------------+---------------------+
| |
+-------------+-----------+ +---+---+
| dvbRcsTdma | |dvbTdm |
+-----+-------------+-----+ +-------+
| |
+-----+-----+ +-----+-----+
|atm-logical| |atm-logical|
+-----------+ +-----------+
Figure 3: Example Stacking
As can be seen from this example, the dvbRcsMacLayer interface is
layered on top of the downstream and upstream interfaces, and the
upstream interface is layered on top of upstream ATM logical links.
Combes, et al. Informational [Page 17]
RFC 5728 DVB-RCS MIB March 2010
In this example, the assignment of index values could be as follows:
ifIndex ifType Description
----------------------------------------------------------------
2 dvbRcsMacLayer (239) DVB-RCS MAC Layer
3 dvbRcsTdma (241) DVB-RCS TDMA Upstream
4 dvbTdm(240) DVB-RCS TDM Downstream
5 atm-logical(80) ATM Logical Port
6 atm-logical(80) ATM Logical Port
The corresponding ifStack entries would then be:
+--------------------+-------------------+
| IfStackHigherLayer | ifStackLowerLayer |
+--------------------+-------------------+
| 0 | 1 |
| 0 | 2 |
| 1 | 0 |
| 2 | 3 |
| 2 | 4 |
| 3 | 5 |
| 3 | 6 |
| 4 | 0 |
| 5 | 0 |
| 6 | 0 |
+--------------------+-------------------+
Table 2: Example ifStack Entries
3.4. MIB Groups Description
3.4.1. dvbRcsRcstSystem
The MIB objects in this group gather some basic information that
would allow anyone to trace the history -- the life -- of the RCST,
as well as to get a complete description of its constitution on the
component point of view, including the SatLabs options/features
support statement. Many of the parameters will be defined at
installation.
This group contains description parameters related to the RCST type
(ODU type) and location. These parameters are believed to stay
unchanged once it has been defined during installation. Modification
of hardware equipment, maintenance operations, and geographical re-
location may require an update of those MIB objects. Note that the
dvbRcsRcstSystem.dvbRcsSystemLocation object gives the location of
Combes, et al. Informational [Page 18]
RFC 5728 DVB-RCS MIB March 2010
the ODU antenna, which is needed for network operation, while the
system.sysLocation (MIB-II SNMP OID) provides the location of the IDU
unit, which cannot be used for the same purpose.
The RCST must provide either Read-Write access to dvbRcsSystemOdu
parameters or, alternatively, provide the list of supported devices
through the dvbRcsRcstOduListGroup (see conformance section). This
group of parameters, defined in the dvbRcsRcstSystem group, allows
the selection by the RCST installer of the actual ODU type. In such
a case, the installer must set dvbRcsOduTxType, dvbRcsOduRxType, and
dvbRcsOduAntennaType according to the selected BUC, LNB, and antenna
respectively.
3.4.2. dvbRcsRcstNetwork
This group contains all the MIB objects related to network
parameters.
In this subgroup, two objects have been defined in order to
differentiate between control and user traffic and associate them
with a physical interface. Both
dvbRcsRcstNetwork.dvbRcsNetworkLanIpAddress (Traffic) and
dvbRcsRcstNetwork.dvbRcsNetworkOamInetAddress (OAM) provide the value
of the IP address of, respectively, the user traffic and the control
and management traffic.
3.4.3. dvbRcsRcstInstall
This group contains all the information related to the RCST
installation and commissioning. Many parameters are believed to stay
unchanged once it has been defined during installation. Modification
of hardware equipment, maintenance operations, and geographical re-
location may require an update of those MIB objects.
3.4.4. dvbRcsRcstQos
This group contains objects to configure the Quality of Service (QoS)
of the RCST by the NCC.
The dvbRcsPktClass table defines the packet classification for IP
layer 3 classifications. Each dvbRcsPktClass entry is mapped to a
dvbRcsPhbEntry in the dvbRcsPhbMappingTable.
The dvbRcsPhbMappingTable makes the relation between a packet
classification entry, a Per-Hop Behavior (PHB) identifier, and a
Request Class entry.
Combes, et al. Informational [Page 19]
RFC 5728 DVB-RCS MIB March 2010
The dvbRcsRequestClassTable defines all the layer 2 DVB-RCS QoS
parameters.
3.4.5. dvbRcsRcstControl
This MIB group contains objects a network manager can use to invoke
actions and tests supported by the RCST agent and to retrieve the
action/test results.
3.4.6. dvbRcsRcstState
This MIB group describes the fault state, software versions, and
configuration file versions of the RCST.
3.4.7. dvbRcsFwdLink (dvbRcsFwdConfig and dvbRcsFwdStatus groups)
This MIB group contains parameters that enable access to data about
the forward link.
Configuration information is kept in the
dvbRcsFwdLink.dvbRcsFwdConfig subgroup. Status information is kept
into the dvbRcsFwdLink.dvbRcsFwdStatus subgroup.
The information in dvbRcsFwdLink.dvbRcsFwdConfig.dvbRcsFwdStartTable
is used for the first time the RCST tries to acquire the forward
link. All these object values are aligned with the Satellite
Delivery System Descriptor in the Network Information Table (NIT)
table [ETSI-SI].
The objects in the dvbRcsFwdLink.dvbRcsFwdConfig.dvbRcsFwdStatusTable
are aligned with the satellite forward path descriptor from the RCS
Map Table (RMT) [ETSI-RCS] and with the Physical Layer (PL) Header
[ETSI-DVBS2], which specifies the MODCOD (modulation and FEC rate)
and the Type (frame length short or long and the presence/absence of
pilots).
3.4.8. dvbRcsRtnLink (dvbRcsRtnConfig and dvbRcsRtnStatus groups)
This MIB group contains parameters that enable access to data about
the return link.
Configuration information is kept in the
dvbRcsRtnLink.dvbRcsRtnConfig subgroup. Status information is kept
into the dvbRcsRtnLink.dvbRcsRtnStatus subgroup.
The RCST is only able to deal with one return link at a time. Hence,
there is no need to define a table to collect the different SNMP
objects, as it is done for the forward.
Combes, et al. Informational [Page 20]
RFC 5728 DVB-RCS MIB March 2010
4. Definitions
DVB-RCS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Integer32,
Unsigned32,
transmission
FROM SNMPv2-SMI -- [RFC2578]
TEXTUAL-CONVENTION,
RowStatus
FROM SNMPv2-TC -- [RFC2579]
OBJECT-GROUP,
MODULE-COMPLIANCE
FROM SNMPv2-CONF -- [RFC2580]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
InetAddressType,
InetAddress,
InetAddressPrefixLength,
InetPortNumber
FROM INET-ADDRESS-MIB -- [RFC4001]
Uri
FROM URI-TC-MIB -- [RFC5017]
Dscp,
DscpOrAny
FROM DIFFSERV-DSCP-TC -- [RFC3289]
;
dvbRcsMib MODULE-IDENTITY
LAST-UPDATED "201002161200Z"
ORGANIZATION "The SatLabs Group"
CONTACT-INFO
"The SatLabs Group
Web: www.satlabs.org
E-mail: info@satlabs.org"
DESCRIPTION
"DVB-RCS MIB subtree.
This MIB module applies to equipment that is a Return
Channel Satellite Terminal (RCST), defined in the Digital
Video Broadcasting Return Channel via Satellite system
(DVB-RCS) standard (ETSI EN 301 790 Digital Video
Broadcasting (DVB); Interaction Channel for Satellite
Distribution Systems, European Telecommunications
Standards Institute (ETSI)).
Combes, et al. Informational [Page 21]
RFC 5728 DVB-RCS MIB March 2010
It defines a set of MIB objects to characterize the
behavior and performance of network-layer entities
implementing DVB-RCS.
This MIB module is intended to be used by DVB-RCS
equipment following the SatLabs System Recommendations,
defined by the SatLabs Group and available at
www.satlabs.org.
Note that, if not stated otherwise in the object
DESCRIPTION clause, all writable objects are
persistent.
Copyright (C) The IETF Trust (2010). This version of
this MIB module is part of RFC 5728; see the RFC itself
for full legal notices."
REVISION "200907201200Z"
DESCRIPTION
"Revision of this MIB module, following MIB doctor review
and adjustments based on the MIB authoring guidelines
from the IETF."
::= { transmission 239 }
--==============================================================
-- Textual Conventions
--==============================================================
DvbRcsSatLabsProfileMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention enumerates the declaration of
the SatLabs-defined terminal profiles. The mapping to
the profiles is to be understood as described here. (0)
refers to the most significant bit.
dvbs(0) -> DVBS profile (DVB-S support)
dvbs2ccm(1) -> DVB-S2 CCM profile (CCM support)
dvbs2acm(2) -> DVB-S2 ACM profile (CCM, VCM and ACM
support)"
REFERENCE
"SatLabs System Recommendations, available at
www.satlabs.org."
SYNTAX BITS {
dvbs(0),
dvbs2ccm(1),
dvbs2acm(2),
spare1(3),
spare2(4),
spare3(5),
spare4(6),
spare5(7),
Combes, et al. Informational [Page 22]
RFC 5728 DVB-RCS MIB March 2010
spare6(8),
spare7(9),
spare8(10),
spare9(11),
spare10(12),
spare11(13),
spare12(14),
spare13(15),
spare14(16),
spare15(17),
spare16(18),
spare17(19),
spare18(20),
spare19(21),
spare20(22),
spare21(23),
spare22(24),
spare23(25),
spare24(26),
spare25(27),
spare26(28),
spare27(29),
spare28(30),
spare29(31)
}
DvbRcsSatLabsOptionMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention enumerates the declaration of
the SatLabs-defined options. A value of 1 indicates
that the respective option is supported. The mapping
to the options is to be understood as described here.
(0) refers to the most significant bit.
mpegTrf(0) -> MPEG_TRF
coarseSync(1) -> COARSE_SYNC
wideHop(2) -> WIDE_HOPP
fastHop(3) -> FAST_HOPP
dynamicMfTdma(4) -> Dynamic_MF_TDMA
contentionSync(5) -> CONTENTION_SYNC
qpskLow(6) -> QPSKLOW
mod16Apsk(7) -> 16APSK
mod32Apsk(8) -> 32APSK
normalFec(9) -> NORMALFEC
multiTs(10) -> MULTITS
gsTs(11) -> GSTS
enhQoS(12) -> ENHQOS
Combes, et al. Informational [Page 23]
RFC 5728 DVB-RCS MIB March 2010
pep(13) -> PEP
http(14) -> HTTP
ftp(15) -> FTP
dns(16) -> DNS
chIdStrict(17) -> CHID_STRICT
nlid(18) -> NLID
snmpMisc(19) -> SNMPMISC
The support of specific options mandates the support of
specific objects and access levels."
REFERENCE
"SatLabs System Recommendations, available at
www.satlabs.org."
SYNTAX BITS {
mpegTrf(0),
coarseSync(1),
wideHop(2),
fastHop(3),
dynamicMfTdma(4),
contentionSync(5),
qpskLow(6),
mod16Apsk(7),
mod32Apsk(8),
normalFec(9),
multiTs(10),
gsTs(11),
enhQoS(12),
pep(13),
http(14),
ftp(15),
dns(16),
chIdStrict(17),
nlid(18),
snmpMisc(19),
spare1(20),
spare2(21),
spare3(22),
spare4(23),
spare5(24),
spare6(25),
spare7(26),
spare8(27),
spare9(28),
spare10(29),
spare11(30),
spare12(31)
}
Combes, et al. Informational [Page 24]
RFC 5728 DVB-RCS MIB March 2010
DvbRcsSatLabsFeatureMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention enumerates the declaration
of the SatLabs-specified compatibility and
configuration features. A value of 1 indicates that
the respective feature is supported. The mapping to
the features is to be understood as described here.
(0) refers to the most significant bit.
rcstPara(0) -> RCST_PARA feature
installLog(1) -> INSTALL_LOG feature
enhClassifier(2) -> ENHCLASSIFIER feature
routeId(3) -> ROUTE_ID feature
oduList(4) -> ODULIST feature
extNetwork(5) -> EXTNETWORK feature
extControl(6) -> EXTCONTROL feature
extConfig(7) -> EXTCONFIG feature
extStatus(8) -> EXTSTATUS feature
mpaf(9) -> MPAF feature
The support of specific features mandates the support of
specific objects and access levels."
REFERENCE
"SatLabs System Recommendations, available at
www.satlabs.org."
SYNTAX BITS {
rcstPara(0),
installLog(1),
enhClassifier(2),
routeId(3),
oduList(4),
extNetwork(5),
extControl(6),
extConfig(7),
extStatus(8),
mpaf(9),
spare1(10),
spare2(11),
spare3(12),
spare4(13),
spare5(14),
spare6(15),
spare7(16),
spare8(17),
spare9(18),
spare10(19),
spare11(20),
Combes, et al. Informational [Page 25]
RFC 5728 DVB-RCS MIB March 2010
spare12(21),
spare13(22),
spare14(23),
spare15(24),
spare16(25),
spare17(26),
spare18(27),
spare19(28),
spare20(29),
spare21(30),
spare22(31)
}
--==============================================================
-- object type definitions
--==============================================================
dvbRcsMibObjects OBJECT IDENTIFIER ::= {dvbRcsMib 1}
dvbRcsConformance OBJECT IDENTIFIER ::= {dvbRcsMib 2}
dvbRcsRcst OBJECT IDENTIFIER ::= {dvbRcsMibObjects 1}
dvbRcsFwdLink OBJECT IDENTIFIER ::= {dvbRcsMibObjects 2}
dvbRcsRtnLink OBJECT IDENTIFIER ::= {dvbRcsMibObjects 3}
dvbRcsRcstSystem OBJECT IDENTIFIER ::= {dvbRcsRcst 1}
dvbRcsRcstNetwork OBJECT IDENTIFIER ::= {dvbRcsRcst 2}
dvbRcsRcstInstall OBJECT IDENTIFIER ::= {dvbRcsRcst 3}
dvbRcsRcstQos OBJECT IDENTIFIER ::= {dvbRcsRcst 4}
dvbRcsRcstControl OBJECT IDENTIFIER ::= {dvbRcsRcst 5}
dvbRcsRcstState OBJECT IDENTIFIER ::= {dvbRcsRcst 6}
dvbRcsFwdConfig OBJECT IDENTIFIER ::= {dvbRcsFwdLink 1}
dvbRcsFwdStatus OBJECT IDENTIFIER ::= {dvbRcsFwdLink 2}
dvbRcsRtnConfig OBJECT IDENTIFIER ::= {dvbRcsRtnLink 1}
dvbRcsRtnStatus OBJECT IDENTIFIER ::= {dvbRcsRtnLink 2}
--==============================================================
-- dvbRcsRcstSystem sub-tree object types
--==============================================================
dvbRcsSystemMibRevision OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object allows the SNMP agent to report the
implemented MIB module revision.
The supported REVISION of this module is reported."
::= {dvbRcsRcstSystem 1}
Combes, et al. Informational [Page 26]
RFC 5728 DVB-RCS MIB March 2010
--==============================================================
-- Options declared according to the textual conventions
--==============================================================
dvbRcsSystemSatLabsProfilesDeclaration OBJECT-TYPE
SYNTAX DvbRcsSatLabsProfileMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the SatLabs profiles supported, as defined in
the SatLabs System Recommendations."
::= {dvbRcsRcstSystem 2}
dvbRcsSystemSatLabsOptionsDeclaration OBJECT-TYPE
SYNTAX DvbRcsSatLabsOptionMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the SatLabs options supported, as defined in
the SatLabs System Recommendations."
::= {dvbRcsRcstSystem 3}
dvbRcsSystemSatLabsFeaturesDeclaration OBJECT-TYPE
SYNTAX DvbRcsSatLabsFeatureMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the optional compatibility features and minor
options supported, as defined in the SatLabs System
Recommendations."
::= {dvbRcsRcstSystem 4}
dvbRcsSystemLocation OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Physical location of the ODU antenna expressed as
longitude, latitude, and altitude. The string
shall have 31 characters in the following format:
<xxxx.xxx>,<a>,<yyyyy.yyy>,<b>,<zzzz.z>,M
where x, y and z represents digits,
a=N or S,
b=E or W,
Reading the digits from left to right:
'x' 7 latitude digits;
x digits 1-2 contain the degrees,
x digits 3-7 contain the minutes in decimal;
'y' 8 longitude digits;
Combes, et al. Informational [Page 27]
RFC 5728 DVB-RCS MIB March 2010
y digits 1-3 contain the degrees,
y digits 4-8 contain the minutes in decimal;
'z' 5 altitude digits;
meters above sea level in decimal;
'.' is the decimal point;
',' is the field separator;
'M' is the indicator for altitude meters.
This format is a modified subset of the NMEA 0183
(National Marine Electronics Association, Interface
Standard) format for Global Positioning System Fix
Data.
This location and the satellite position are used to
calculate the RCST-satellite path delay.
Note: The system.sysLocation object of MIB-II provides
physical location of the IDU unit."
::= {dvbRcsRcstSystem 5}
dvbRcsSystemOduAntennaSize OBJECT-TYPE
SYNTAX Unsigned32
UNITS "cm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Diameter of the antenna."
::= {dvbRcsRcstSystem 6}
dvbRcsSystemOduAntennaGain OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dBi"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Antenna peak gain of the ODU."
::= {dvbRcsRcstSystem 7}
dvbRcsSystemOduSspa OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 W"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Power level of the Solid State Power Amplifier
installed in the ODU."
::= {dvbRcsRcstSystem 8}
dvbRcsSystemOduTxType OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
Combes, et al. Informational [Page 28]
RFC 5728 DVB-RCS MIB March 2010
STATUS current
DESCRIPTION
"Type of transmitter installed in the ODU."
::= {dvbRcsRcstSystem 9}
dvbRcsSystemOduRxType OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of LNB installed in the ODU, with
information such as vendor type, output type (single,
twin, quad,...), etc."
::= {dvbRcsRcstSystem 10}
dvbRcsSystemOduRxBand OBJECT-TYPE
SYNTAX INTEGER {
oduHighRxBand (0),
oduLowRxBand (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"LNB High Band / Low Band selector. High Band corresponds
to the emission of an 18-26 kHz tone with 0.4-0.8 Vpp in
the Rx IFL cable:
(0) - High Band
(1) - Low Band"
::= {dvbRcsRcstSystem 11}
dvbRcsSystemOduRxLO OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of LNB Local Oscillator (in 100 Hz)"
::= {dvbRcsRcstSystem 12}
dvbRcsSystemOduTxLO OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of Block Up-Converter Local Oscillator
(in 100 Hz)."
::= {dvbRcsRcstSystem 13}
Combes, et al. Informational [Page 29]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsSystemIduPep OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 14}
dvbRcsTcpPep OBJECT-TYPE
SYNTAX INTEGER{
disabled (0),
enabled (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status and control of embedded TCP PEP.
0 - disabled or not implemented
1 - enabled"
::={dvbRcsSystemIduPep 1}
dvbRcsHttpPep OBJECT-TYPE
SYNTAX INTEGER{
disabled (0),
enabled (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status and control of embedded HTTP PEP.
0 - disabled or not implemented
1 - enabled"
::={dvbRcsSystemIduPep 2}
--==============================================================
-- ODU structural entities
--==============================================================
dvbRcsOduTx OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 15}
dvbRcsOduRx OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 16}
dvbRcsOduAntenna OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 17}
--==============================================================
-- ODU BUC
--==============================================================
dvbRcsOduTxTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsOduTxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the identification of each well-
known BUC type supported by the IDU and provides its
associated index."
Combes, et al. Informational [Page 30]
RFC 5728 DVB-RCS MIB March 2010
::={dvbRcsOduTx 1}
dvbRcsOduTxTypeEntry OBJECT-TYPE
SYNTAX DvbRcsOduTxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the BUC type table."
INDEX { dvbRcsOduTxTypeIndex }
::={dvbRcsOduTxTypeTable 1}
DvbRcsOduTxTypeEntry ::= SEQUENCE {
dvbRcsOduTxTypeIndex Unsigned32,
dvbRcsOduTxTypeDescription SnmpAdminString
}
dvbRcsOduTxTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the BUC type."
::={dvbRcsOduTxTypeEntry 1}
dvbRcsOduTxTypeDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Text-based identification of a BUC type."
::={dvbRcsOduTxTypeEntry 2}
dvbRcsOduTxType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Index of the selected BUC type."
::={dvbRcsOduTx 2}
--==============================================================
-- ODU LNB
--==============================================================
dvbRcsOduRxTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsOduRxTypeEntry
MAX-ACCESS not-accessible
STATUS current
Combes, et al. Informational [Page 31]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"This table contains the identification of each well-
known LNB type supported by the IDU and provides its
associated index."
::={dvbRcsOduRx 1}
dvbRcsOduRxTypeEntry OBJECT-TYPE
SYNTAX DvbRcsOduRxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the LNB type table."
INDEX { dvbRcsOduRxTypeIndex }
::={dvbRcsOduRxTypeTable 1}
DvbRcsOduRxTypeEntry ::= SEQUENCE {
dvbRcsOduRxTypeIndex Unsigned32,
dvbRcsOduRxTypeDescription SnmpAdminString
}
dvbRcsOduRxTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the LNB type."
::={dvbRcsOduRxTypeEntry 1}
dvbRcsOduRxTypeDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Text-based identification of an LNB type."
::={dvbRcsOduRxTypeEntry 2}
dvbRcsOduRxType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Index of the selected LNB type."
::={dvbRcsOduRx 2}
Combes, et al. Informational [Page 32]
RFC 5728 DVB-RCS MIB March 2010
--==============================================================
-- ODU Antenna
--==============================================================
dvbRcsOduAntennaTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsOduAntennaTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the identification of each well-
known antenna type supported by the IDU and provides
its associated index."
::={dvbRcsOduAntenna 1}
dvbRcsOduAntennaTypeEntry OBJECT-TYPE
SYNTAX DvbRcsOduAntennaTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the antenna type table."
INDEX { dvbRcsOduAntennaTypeIndex }
::={dvbRcsOduAntennaTypeTable 1}
DvbRcsOduAntennaTypeEntry ::= SEQUENCE {
dvbRcsOduAntennaTypeIndex Unsigned32,
dvbRcsOduAntennaTypeDescription SnmpAdminString
}
dvbRcsOduAntennaTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the antenna type."
::={dvbRcsOduAntennaTypeEntry 1}
dvbRcsOduAntennaTypeDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Text-based identification of an antenna type."
::={dvbRcsOduAntennaTypeEntry 2}
dvbRcsOduAntennaType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
Combes, et al. Informational [Page 33]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"Index of the selected antenna type."
::={dvbRcsOduAntenna 2}
--==============================================================
-- dvbRcsRcstNetwork sub-tree object types
--==============================================================
dvbRcsNetworkOamInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsNetworkOamInetAddress.
If the terminal OAM Internet address is unassigned or
unknown, then the value of this object is unknown(0)."
::= {dvbRcsRcstNetwork 1}
dvbRcsNetworkOamInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"OAM IP Address of the RCST. This object is used with
both IP and interfaces MIB-II subgroups. It uniquely
determines the interface through which OAM traffic
passes.
The OAM IP address may be statically or dynamically
assigned. It is system dependent whether the OAM IP
address and the Traffic IP address are the same address.
If the terminal has no OAM Internet address assigned or if
this Internet address is unknown, the value of this
object is the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkOamInetAddressType object."
::= {dvbRcsRcstNetwork 2}
dvbRcsNetworkOamInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the OAM IP Address. If this address
prefix is unknown or does not apply, the value is zero."
::= {dvbRcsRcstNetwork 3}
dvbRcsNetworkOamInetAddressAssign OBJECT-TYPE
Combes, et al. Informational [Page 34]
RFC 5728 DVB-RCS MIB March 2010
SYNTAX INTEGER {
oamInetAddressStatic (1),
oamInetAddressDynamic (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Identifies whether the OAM IP address is statically
(1) or dynamically (2) assigned."
::= {dvbRcsRcstNetwork 4}
dvbRcsNetworkLanInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of dvbRcsNetworkLanInetAddress.
If the terminal Internet address on the LAN interface is
unassigned or unknown, then the value of this object is
unknown(0)."
::= {dvbRcsRcstNetwork 5}
dvbRcsNetworkLanInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the LAN interface of the terminal. If the
terminal has no Internet address assigned on the LAN
interface or if this Internet address is unknown, the
value of this object is the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkLanInetAddressType object."
::= {dvbRcsRcstNetwork 6}
dvbRcsNetworkLanInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the LAN IP Address of the terminal.
If this address prefix is unknown or does not apply, the
value is zero."
::= {dvbRcsRcstNetwork 7}
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType
OBJECT-TYPE
SYNTAX InetAddressType
Combes, et al. Informational [Page 35]
RFC 5728 DVB-RCS MIB March 2010
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress.
If the default gateway Internet address is unassigned or
unknown, then the value of this object is unknown(0)."
::= {dvbRcsRcstNetwork 8}
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the default gateway for the air
interface. If the terminal has no default gateway
assigned on the air interface or if this Internet address
is unknown, the value of this object is the zero-length
OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType
object."
::= {dvbRcsRcstNetwork 9}
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressPrefixLength
OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the default gateway
for the air interface.
If this address prefix is unknown or does not apply, the
value is zero."
::= {dvbRcsRcstNetwork 10}
dvbRcsNetworkDnsServers OBJECT IDENTIFIER ::= {dvbRcsRcstNetwork
11}
dvbRcsPrimaryDnsServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsPrimaryDnsServerInetAddress. If the primary DNS
server Internet address is unassigned or unknown, then
the value of this object is unknown(0)."
Combes, et al. Informational [Page 36]
RFC 5728 DVB-RCS MIB March 2010
::= { dvbRcsNetworkDnsServers 1}
dvbRcsPrimaryDnsServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the primary DNS server in the NCC. If
the terminal has no primary DNS server assigned or if this
Internet address is unknown, the value of this object is
the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsPrimaryDnsServerInetAddressType object."
::= {dvbRcsNetworkDnsServers 2}
dvbRcsPrimaryDnsServerInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the primary DNS
server in the NCC.
If this address prefix is unknown or does not apply, the
value is zero."
::= { dvbRcsNetworkDnsServers 3}
dvbRcsSecondaryDnsServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsSecondaryDnsServerInetAddress. If the secondary
DNS server Internet address is unassigned or unknown,
then the value of this object is unknown(0)."
::= { dvbRcsNetworkDnsServers 4}
dvbRcsSecondaryDnsServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the secondary DNS server in the NCC. If
the terminal has no secondary DNS server assigned or if
this Internet address is unknown, the value of this
object is the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsSecondaryDnsServerInetAddressType object."
Combes, et al. Informational [Page 37]
RFC 5728 DVB-RCS MIB March 2010
::= {dvbRcsNetworkDnsServers 5}
dvbRcsSecondaryDnsServerInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the secondary DNS
server in the NCC.
If this address prefix is unknown or does not apply, the
value is zero."
::= { dvbRcsNetworkDnsServers 6}
dvbRcsNetworkNccMgtInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsNetworkNccMgtInetAddress. If the management server
Internet address is unassigned or unknown, then the
value of this object is unknown(0)."
::= {dvbRcsRcstNetwork 12}
dvbRcsNetworkNccMgtInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the management server in the NCC. If
the terminal has no management server assigned or if this
Internet address is unknown, the value of this object is
the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkNccMgtInetAddressType object."
::= {dvbRcsRcstNetwork 13}
dvbRcsNetworkNccMgtInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the management
server in the NCC.
If this address prefix is unknown or does not apply, the
value is zero."
::= { dvbRcsRcstNetwork 14}
Combes, et al. Informational [Page 38]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsNetworkConfigFileDownloadUrl OBJECT-TYPE
SYNTAX Uri (SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path name for the configuration file download.
It includes the protocol type (TFTP or FTP) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 15}
dvbRcsNetworkInstallLogFileDownloadUrl OBJECT-TYPE
SYNTAX Uri (SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the installation log file to download.
It includes the protocol type (TFTP or FTP) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST. The
installation log file can be created on the installer's
computer and downloaded to the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 16}
dvbRcsNetworkConfigFileUploadUrl OBJECT-TYPE
SYNTAX Uri(SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path name for the configuration file upload.
It includes the protocol type (TFTP or FTP) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 17}
Combes, et al. Informational [Page 39]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsNetworkLogFileUploadUrl OBJECT-TYPE
SYNTAX Uri(SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the event log file. It includes the
protocol type (TFTP or FTP) and the associated server IP
address or hostname. Hostname can only be used if DNS is
supported by the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 18}
dvbRcsNetworkInstallLogFileUploadUrl OBJECT-TYPE
SYNTAX Uri(SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the installation log file. It includes the
protocol type (TFTP or FTP) and the associated server
IP address or hostname. Hostname can only be used if DNS
is supported by the RCST. The installation log file can
be retrieved from the RCST by the NCC or by the
installer via the LAN.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 19}
--==============================================================
-- dvbRcsRcstInstall sub-tree object types
--==============================================================
dvbRcsInstallAntennaAlignmentState OBJECT-TYPE
SYNTAX INTEGER {
antennaAlignmentStart (1),
antennaAlignmentDeny (2),
antennaAlignmentContinue(3),
antennaAlignmentStop (4),
antennaAlignmentSuccess (5),
antennaAlignmentFail (6)
}
MAX-ACCESS read-write
STATUS current
Combes, et al. Informational [Page 40]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"Indicates the alignment state of the antenna:
(1)-Start;
(2)-Deny;
(3)-Continue;
(4)-Stop;
(5)-Success;
(6)-Fail"
::= {dvbRcsRcstInstall 1}
dvbRcsInstallCwFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of the transmitted Continuous Wave
carrier (in 100 Hz).
Minimum required precision is 1 kHz."
::= {dvbRcsRcstInstall 2}
dvbRcsInstallCwMaxDuration OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time after which the Continuous Wave carrier must be
put down (in seconds)."
::= {dvbRcsRcstInstall 3}
dvbRcsInstallCwPower OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IDU TX output level when the IDU is configured to send
CW. The resolution is 0.1 dBm and the accuracy is +/- 1
dBm. Reconfiguration is applied immediately to a CW."
::= {dvbRcsRcstInstall 4}
Combes, et al. Informational [Page 41]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsInstallCoPolReading OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Co-polarization measured value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 5}
dvbRcsInstallXPolReading OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Cross-polarization measured value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 6}
dvbRcsInstallCoPolTarget OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Co-polarization target value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 7}
dvbRcsInstallXPolTarget OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Cross-polarization target value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 8}
dvbRcsInstallStandByDuration OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time to wait in stand-by mode (in seconds)."
::= {dvbRcsRcstInstall 9}
Combes, et al. Informational [Page 42]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsInstallTargetEsN0 OBJECT-TYPE
SYNTAX Unsigned32(0..315)
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This value describes the wanted Es/N0 value that
enables operation of the return link with the required
error performance. The values shall be given in tenth of
dB and the initial value shall be equal to 7 dB. The
range shall be from 0 dB to 31.5 dB, with a precision
of 0.1 dB."
DEFVAL { 70 }
::= {dvbRcsRcstInstall 10}
--==============================================================
-- dvbRcsRcstQos sub-tree object types
--==============================================================
dvbRcsPktClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsPktClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the packet classification used in
the DVB-RCS terminal. The number of entries is specified
by dvbRcsPktClassIndex. "
::={dvbRcsRcstQos 1}
dvbRcsPktClassEntry OBJECT-TYPE
SYNTAX DvbRcsPktClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the packet classification table. One object
type of each entry may have a value in the active range
(a non-default value). The other object types are then
assumed to be set to 'inactive'. The entry with the lowest
index value takes precedence when classifying a packet."
INDEX { dvbRcsPktClassIndex }
::= {dvbRcsPktClassTable 1}
DvbRcsPktClassEntry ::= SEQUENCE {
dvbRcsPktClassIndex Unsigned32,
dvbRcsPktClassDscpLow Dscp,
dvbRcsPktClassDscpHigh Dscp,
dvbRcsPktClassDscpMarkValue DscpOrAny,
dvbRcsPktClassIpProtocol Unsigned32,
dvbRcsPktClassSrcInetAddressType InetAddressType,
Combes, et al. Informational [Page 43]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsPktClassSrcInetAddress InetAddress,
dvbRcsPktClassSrcInetAddressPrefixLength
InetAddressPrefixLength,
dvbRcsPktClassDstInetAddressType InetAddressType,
dvbRcsPktClassDstInetAddress InetAddress,
dvbRcsPktClassDstInetAddressPrefixLength
InetAddressPrefixLength,
dvbRcsPktClassSrcPortLow InetPortNumber,
dvbRcsPktClassSrcPortHigh InetPortNumber,
dvbRcsPktClassDstPortLow InetPortNumber,
dvbRcsPktClassDstPortHigh InetPortNumber,
dvbRcsPktClassVlanUserPri Integer32,
dvbRcsPktClassPhbAssociation Unsigned32,
dvbRcsPktClassRowStatus RowStatus
}
dvbRcsPktClassIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..64)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index automatically incremented by one at row
creation."
::={dvbRcsPktClassEntry 1}
dvbRcsPktClassDscpLow OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low value of a range of
Diffserv Code Point (DSCP) values to which a packet is
compared."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 2}
dvbRcsPktClassDscpHigh OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high value of a range of
Diffserv Code Point (DSCP) values to which a packet is
compared."
DEFVAL { 63 }
::={dvbRcsPktClassEntry 3}
dvbRcsPktClassDscpMarkValue OBJECT-TYPE
Combes, et al. Informational [Page 44]
RFC 5728 DVB-RCS MIB March 2010
SYNTAX DscpOrAny
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is the Diffserv Code Point (DSCP) value
used to mark the packet; -1 indicates no DSCP marking.
Possible DSCP marks values are (0..63)"
DEFVAL { -1 }
::={dvbRcsPktClassEntry 4}
dvbRcsPktClassIpProtocol OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP protocol to which a
packet is compared. A value of 255 means match all."
DEFVAL { 255 }
::={dvbRcsPktClassEntry 5}
dvbRcsPktClassSrcInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsPktClassSrcInetAddress. If the packet class source
Internet address is unassigned or unknown, then the
value of this object is unknown(0)."
::= { dvbRcsPktClassEntry 6}
dvbRcsPktClassSrcInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP source address to which a
packet is compared. If the packet class has no source
Internet address assigned or if this Internet address is
unknown, the value of this object is the zero-length
OCTET STRING.
The InetAddressType is given by the
dvbRcsPktClassSrcInetAddressType object."
::={dvbRcsPktClassEntry 7}
dvbRcsPktClassSrcInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
Combes, et al. Informational [Page 45]
RFC 5728 DVB-RCS MIB March 2010
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Prefix length of the IP source address that will be
matched for this packet class. A value of zero indicates
that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 8}
dvbRcsPktClassDstInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsPktClassDstInetAddress. If the packet class
destination Internet address is unassigned or unknown,
then the value of this object is unknown(0)."
::= { dvbRcsPktClassEntry 9}
dvbRcsPktClassDstInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP destination address to
which a packet is compared. If the packet class has no
destination Internet address assigned or if this Internet
address is unknown, the value of this object is the
zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsPktClassDstInetAddressType object."
::={dvbRcsPktClassEntry 10}
dvbRcsPktClassDstInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Prefix length of the IP source address that will be
matched for this packet class. A value of zero indicates
that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 11}
Combes, et al. Informational [Page 46]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsPktClassSrcPortLow OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low range of the source
port to which a packet is compared. A value of 0
indicates that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 12}
dvbRcsPktClassSrcPortHigh OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high range of the source port
to which a packet is compared. A value of 0 indicates
that the selectivity is inactive."
DEFVAL { 65535 }
::={dvbRcsPktClassEntry 13}
dvbRcsPktClassDstPortLow OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low range of the destination
port to which a packet is compared. A value of 0
indicates that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 14}
dvbRcsPktClassDstPortHigh OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high range of the destination
port to which a packet is compared. A value of 0
indicates that the selectivity is inactive."
DEFVAL { 65535 }
::={dvbRcsPktClassEntry 15}
dvbRcsPktClassVlanUserPri OBJECT-TYPE
SYNTAX Integer32 (-1..7)
MAX-ACCESS read-create
STATUS current
Combes, et al. Informational [Page 47]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"This object specifies the VLAN User Priority to which a
packet is compared. A value of -1 indicates that the
selectivity is inactive."
DEFVAL { -1 }
::={dvbRcsPktClassEntry 16}
dvbRcsPktClassPhbAssociation OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Associate the filter entry to a specific PHB (refer to
dvbRcsPhbIdentifier)."
::={dvbRcsPktClassEntry 17}
dvbRcsPktClassRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects
in this row may be modified at any time."
::={dvbRcsPktClassEntry 18}
--==============================================================
-- dvbRcsPhbMappingTable
--==============================================================
dvbRcsPhbMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsPhbMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a list of Per-Hop Behavior (PHB) MIB
entries.
It describes the PHB mapping to the Request Class."
::={dvbRcsRcstQos 2}
dvbRcsPhbMappingEntry OBJECT-TYPE
SYNTAX DvbRcsPhbMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the PHB mapping table."
INDEX {dvbRcsPhbIdentifier}
::= {dvbRcsPhbMappingTable 1}
DvbRcsPhbMappingEntry ::= SEQUENCE {
Combes, et al. Informational [Page 48]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsPhbIdentifier Unsigned32,
dvbRcsPhbName
SnmpAdminString,
dvbRcsPhbRequestClassAssociation Unsigned32,
dvbRcsPhbMappingRowStatus RowStatus
}
dvbRcsPhbIdentifier OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identification of the Per-Hop Behavior (PHB). It
follows the unsigned 16-bit binary encoding as specified
in RFC 3140. The value 0 designates the Default PHB."
::={dvbRcsPhbMappingEntry 1}
dvbRcsPhbName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name of the Per-Hop Behavior (PHB)."
::={dvbRcsPhbMappingEntry 2}
dvbRcsPhbRequestClassAssociation OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is an association of this Per-Hop Behavior
(PHB) to a Request Class (by reference to a Request
Class index)."
::={dvbRcsPhbMappingEntry 3}
dvbRcsPhbMappingRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable
objects in this row may be modified at any time."
DEFVAL { active }
::={dvbRcsPhbMappingEntry 4}
Combes, et al. Informational [Page 49]
RFC 5728 DVB-RCS MIB March 2010
--==============================================================
-- dvbRcsRequestClassTable
--==============================================================
dvbRcsRequestClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsRequestClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a list of Request Class entries. This
class describes the layer 2 QoS objects."
::={dvbRcsRcstQos 3}
dvbRcsRequestClassEntry OBJECT-TYPE
SYNTAX DvbRcsRequestClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Request Class table."
INDEX {dvbRcsRequestClassIndex}
::= {dvbRcsRequestClassTable 1}
DvbRcsRequestClassEntry ::= SEQUENCE {
dvbRcsRequestClassIndex Unsigned32,
dvbRcsRequestClassName
SnmpAdminString,
dvbRcsRequestClassChanId Unsigned32,
dvbRcsRequestClassVccVpi Unsigned32,
dvbRcsRequestClassVccVci Unsigned32,
dvbRcsRequestClassPidPoolReference Unsigned32,
dvbRcsRequestClassCra Unsigned32,
dvbRcsRequestClassRbdcMax Unsigned32,
dvbRcsRequestClassRbdcTimeout Unsigned32,
dvbRcsRequestClassVbdcMax Unsigned32,
dvbRcsRequestClassVbdcTimeout Unsigned32,
dvbRcsRequestClassVbdcMaxBackLog Unsigned32,
dvbRcsRequestClassRowStatus RowStatus
}
dvbRcsRequestClassIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the Request Class table. A total of 16 entries
are supported."
::={dvbRcsRequestClassEntry 1}
dvbRcsRequestClassName OBJECT-TYPE
Combes, et al. Informational [Page 50]
RFC 5728 DVB-RCS MIB March 2010
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Name of the Request Class."
::={dvbRcsRequestClassEntry 2}
dvbRcsRequestClassChanId OBJECT-TYPE
SYNTAX Unsigned32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Channel ID of the Request Class."
::={dvbRcsRequestClassEntry 3}
dvbRcsRequestClassVccVpi OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the VPI used for the Request Class (ATM profile)."
::={dvbRcsRequestClassEntry 4}
dvbRcsRequestClassVccVci OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the VCI used for the Request Class (ATM profile)."
::={dvbRcsRequestClassEntry 5}
dvbRcsRequestClassPidPoolReference OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Reference to the Packet IDentifier (PID) pool
applicable for the Request Class."
::={dvbRcsRequestClassEntry 6}
dvbRcsRequestClassCra OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bit/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the Continuous Rate Assignment (CRA) level for the
Request Class in bits per second (bit/s)."
Combes, et al. Informational [Page 51]
RFC 5728 DVB-RCS MIB March 2010
::={dvbRcsRequestClassEntry 7}
dvbRcsRequestClassRbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x2 kbit/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Rate-Based Dynamic Capacity (RBDC) that can be
requested for the Request Class, in number of 2 kbit/s."
::={dvbRcsRequestClassEntry 8}
dvbRcsRequestClassRbdcTimeout OBJECT-TYPE
SYNTAX Unsigned32
UNITS "superframes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Persistence of the Rate-Based Dynamic Capacity (RBDC)
request, expressed in superframes."
::={dvbRcsRequestClassEntry 9}
dvbRcsRequestClassVbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "ATM cells/MPEG packets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Volume-Based Dynamic Capacity (VBDC) that can
be allocated to the Request Class, in payload units (one
ATM cell or one MPEG packet) per superframe."
::={dvbRcsRequestClassEntry 10}
dvbRcsRequestClassVbdcTimeout OBJECT-TYPE
SYNTAX Unsigned32
UNITS "superframes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Time after which the RCST considers that the pending
requests are lost. The RCST may issue new requests for
that traffic. Volume-Based Dynamic Capacity (VBDC)
Timeout is expressed in superframes."
::={dvbRcsRequestClassEntry 11}
dvbRcsRequestClassVbdcMaxBackLog OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
Combes, et al. Informational [Page 52]
RFC 5728 DVB-RCS MIB March 2010
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Volume-Based Dynamic Capacity (VBDC) back log per
Request Class (expressed in bytes)."
::={dvbRcsRequestClassEntry 12}
dvbRcsRequestClassRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. It is not possible
to change values in a row of this table while the row is
active."
::={dvbRcsRequestClassEntry 13}
--==============================================================
-- The table of PID pools
--==============================================================
dvbRcsPidPoolTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsPidPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the Packet IDentifier (PID) pools.
For the MPEG profile, several Request Classes may be mapped
within a pool of several PIDs to allow Section Packing
across several Request Classes.
A PID value may occur in more than one PID pool. Each
PID value can effectively occur only once in each pool."
::={dvbRcsRcstQos 4}
dvbRcsPidPoolEntry OBJECT-TYPE
SYNTAX DvbRcsPidPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the PID pool table."
INDEX { dvbRcsPidPoolIndex, dvbRcsPidIndex }
::= {dvbRcsPidPoolTable 1}
DvbRcsPidPoolEntry ::= SEQUENCE {
dvbRcsPidPoolIndex Unsigned32,
dvbRcsPidIndex Unsigned32,
dvbRcsPidValue Unsigned32,
dvbRcsPidPoolRowStatus RowStatus
Combes, et al. Informational [Page 53]
RFC 5728 DVB-RCS MIB March 2010
}
dvbRcsPidPoolIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the PID pool in the PID pool table."
::={dvbRcsPidPoolEntry 1}
dvbRcsPidIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the PID entry within the PID pool."
::={dvbRcsPidPoolEntry 2}
dvbRcsPidValue OBJECT-TYPE
SYNTAX Unsigned32 (0..8191)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines one of the PIDs to be used in a PID pool of
dvbRcsPidPoolIndex.
A PID value may occur in more than one PID pool. Each
PID value can effectively occur only once in each pool."
::={dvbRcsPidPoolEntry 3}
dvbRcsPidPoolRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable
objects in this row may be modified at any time."
DEFVAL { active }
::={dvbRcsPidPoolEntry 4}
dvbRcsQosGlobalRbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x2 kbit/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global maximum RBDC that can be requested for the RCST,
in number of 2 kbit/s."
::={dvbRcsRcstQos 5}
Combes, et al. Informational [Page 54]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsQosGlobalVbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "ATM cells/MPEG packets"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global maximum VBDC that can be allocated to the RCST,
in payload units (one ATM cell or one MPEG packet) per
superframe."
::={dvbRcsRcstQos 6}
dvbRcsQosGlobalVbdcMaxBackLog OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global VBDC back log at the RCST level (expressed in
bytes). It is used only if the VBDC back log is not
configured in the Request Class (expressed in bytes)."
::={dvbRcsRcstQos 7}
dvbRcsQosChannelIdStrictDispatching OBJECT-TYPE
SYNTAX INTEGER {
notStrict (0),
strict (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the RCST will strictly follow RC
association when signaled through Channel_ID in the
TBTP:
(0)- no strict association
(1)- strict association"
::={dvbRcsRcstQos 8}
--==============================================================
-- dvbRcsRcstControl sub-tree object types
--==============================================================
dvbRcsCtrlRebootCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
normal (2),
alternate (3)
}
MAX-ACCESS read-write
STATUS current
Combes, et al. Informational [Page 55]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"This variable shall force the RCST to reboot:
(1)- idle
(2)- normal reboot (from current software load)
(3)- reboot from alternate load (swap to alternate
load before reboot)"
DEFVAL {idle}
::={dvbRcsRcstControl 1}
dvbRcsCtrlRcstTxDisable OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall force the RCST to stop transmission
(transmit disabled as defined in SatLabs System
Recommendations):
(1)- idle
(2)- initiate Tx Disabled"
DEFVAL {idle}
::={dvbRcsRcstControl 2}
dvbRcsCtrlUserTrafficDisable OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall disable user traffic (only RCST
management traffic can be transmitted):
(1)- idle
(2)- disable user traffic"
DEFVAL {idle}
::={dvbRcsRcstControl 3}
dvbRcsCtrlCwEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Combes, et al. Informational [Page 56]
RFC 5728 DVB-RCS MIB March 2010
"This variable will force the RCST to start transmission
of CW, if the RCST is first set to the installation
state and is properly configured for CW transmission:
(1)- off
(2)- on"
DEFVAL {off}
::={dvbRcsRcstControl 4}
dvbRcsCtrlOduTxReferenceEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of the 10 MHz reference
clock in the Tx IFL cable:
(1) off
(2) on"
DEFVAL {on}
::={dvbRcsRcstControl 5}
dvbRcsCtrlOduTxDCEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of DC in the Tx IFL
cable:
(1) off
(2) on"
DEFVAL {on}
::={dvbRcsRcstControl 6}
dvbRcsCtrlOduRxDCEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of DC in the Rx IFL
cable:
Combes, et al. Informational [Page 57]
RFC 5728 DVB-RCS MIB March 2010
(1) off
(2) on"
DEFVAL {on}
::={dvbRcsRcstControl 7}
dvbRcsCtrlDownloadFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
config (2),
installationLog (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST configuration file
download process:
(1) idle
(2) download RCST configuration file from TFTP/FTP
server
(3) download RCST installation log file from TFTP/FTP
server (INSTALL_LOG feature)"
DEFVAL {idle}
::={dvbRcsRcstControl 8}
dvbRcsCtrlUploadFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
config (2),
eventAlarm (3),
installationLog (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST upload process:
(1) idle
(2) upload RCST configuration file to TFTP/FTP server
(3) upload RCST event/alarm log file to TFTP/FTP server
(4) upload RCST installation log file to TFTP/FTP server
(INSTALL_LOG feature)"
DEFVAL {idle}
::={dvbRcsRcstControl 9}
dvbRcsCtrlActivateConfigFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
activate (2)
}
Combes, et al. Informational [Page 58]
RFC 5728 DVB-RCS MIB March 2010
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Triggers the RCST to use the configuration file and
update its parameters accordingly. Some RCST
implementations may require a reboot for the parameters
to take effect (vendor specific).
(1) idle
(2) activate"
DEFVAL {idle}
::={dvbRcsRcstControl 10}
dvbRcsCtrlRcstLogonCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
logon (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST logon:
(1) idle
(2) initiate RCST logon"
DEFVAL {idle}
::={dvbRcsRcstControl 11}
dvbRcsCtrlRcstLogoffCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
logoff (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST logoff:
(1) idle
(2) initiate RCST logoff"
DEFVAL {idle}
::={dvbRcsRcstControl 12}
dvbRcsCtrlRcstRxReacquire OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
reacquireForwardLink (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Combes, et al. Informational [Page 59]
RFC 5728 DVB-RCS MIB March 2010
"This variable will force the RCST to acquire the
forward link and start receiving:
(1) idle
(2) reacquire forward link"
DEFVAL {idle}
::={dvbRcsRcstControl 13}
--==============================================================
-- dvbRcsRcstState sub-tree object types
--==============================================================
dvbRcsRcstMode OBJECT-TYPE
SYNTAX INTEGER {
installation (0),
operational (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Identifies the current mode of the RCST and allows the RCST
to return to the installation mode when needed. Values for
the RCST mode are:
Installation (0)
Operational (1)"
::={dvbRcsRcstState 1}
dvbRcsRcstFaultStatus OBJECT-TYPE
SYNTAX INTEGER {
nofault (0),
fault (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the fault status of the terminal. The fault
status management is vendor specific. Values for the
fault status are:
no fault (0)
fault (1)"
::={dvbRcsRcstState 2}
dvbRcsRcstFwdLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
notAcquired (0),
acquired (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Combes, et al. Informational [Page 60]
RFC 5728 DVB-RCS MIB March 2010
"Provides the status of the RCST forward link. Values
for the forward link status are:
Not acquired (0)
Acquired (1)"
::={dvbRcsRcstState 3}
dvbRcsRcstRtnLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
loggedOff (0),
loggedOn (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the status of the RCST return link. Values for
the return link status are:
Logged-off (0)
Logged-on (1)"
::={dvbRcsRcstState 4}
dvbRcsRcstLogUpdated OBJECT-TYPE
SYNTAX INTEGER {
noUpdate (0),
logfileUpdated (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the existence of an updated event log file:
No update (0)
Event Log file updated (1)
The RCST should remove the 'Event Log file updated'
indication as the log file is fetched by the NCC."
::={dvbRcsRcstState 5}
dvbRcsRcstCurrentSoftwareVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current RCST software version."
::={dvbRcsRcstState 6}
dvbRcsRcstAlternateSoftwareVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Combes, et al. Informational [Page 61]
RFC 5728 DVB-RCS MIB March 2010
"Alternate (backup/new) RCST software version."
::={dvbRcsRcstState 7}
dvbRcsRcstActivatedConfigFileVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the most recently activated configuration
file.
The version is vendor specific."
::={dvbRcsRcstState 8}
dvbRcsRcstDownloadedConfigFileVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the most recently downloaded configuration
file.
Version is vendor specific. If the value is different
from dvbRcsRcstActivatedConfigFileVersion, it is pending
for activation."
::={dvbRcsRcstState 9}
--==============================================================
-- dvbRcsFwdConfig sub-tree object types
--==============================================================
dvbRcsFwdStartTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsFwdStartEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Lists forward link attachment points (e.g., different
for installation and operation).
The table describes the forward link parameters used for
the start-up stream with the NCC."
::={dvbRcsFwdConfig 1}
dvbRcsFwdStartEntry OBJECT-TYPE
SYNTAX DvbRcsFwdStartEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Forward Link Start Configuration table."
INDEX {dvbRcsFwdStartIndex}
::= {dvbRcsFwdStartTable 1}
Combes, et al. Informational [Page 62]
RFC 5728 DVB-RCS MIB March 2010
DvbRcsFwdStartEntry ::= SEQUENCE {
dvbRcsFwdStartIndex Unsigned32,
dvbRcsFwdStartPopId Integer32,
dvbRcsFwdStartFrequency Unsigned32,
dvbRcsFwdStartPolar INTEGER,
dvbRcsFwdStartFormat INTEGER,
dvbRcsFwdStartRolloff INTEGER,
dvbRcsFwdStartSymbolRate Unsigned32,
dvbRcsFwdStartInnerFec INTEGER,
dvbRcsFwdStartRowStatus RowStatus
}
dvbRcsFwdStartIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the Forward Link StartConfig table."
::={dvbRcsFwdStartEntry 1}
dvbRcsFwdStartPopId OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Population identifier associated with the start-up
forward link:
-1: any (auto)
0-65535: specific StartPopId
If 'any' is set, the RCST will assume membership of any
announced population ID and will commence with logon in
accordance with this assumption."
::={dvbRcsFwdStartEntry 2}
dvbRcsFwdStartFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Frequency of the start transponder carrying a
Network Information Table to which any RCST shall
trigger to acquire forward link. Its value shall be
given in multiples of 100 kHz."
::={dvbRcsFwdStartEntry 3}
dvbRcsFwdStartPolar OBJECT-TYPE
SYNTAX INTEGER {
Combes, et al. Informational [Page 63]
RFC 5728 DVB-RCS MIB March 2010
linearHorizontal (0),
linearVertical (1),
circularLeft (2),
circularRight (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"2-bit field giving the polarization of the start
transponder carrying a Network Information Table to
which any RCST shall trigger to acquire forward link:
00: linear and horizontal
01: linear and vertical
10: circular left
11: circular right"
::={dvbRcsFwdStartEntry 4}
dvbRcsFwdStartFormat OBJECT-TYPE
SYNTAX INTEGER {
auto (-1),
dvbs (0),
dvbs2ccm (1),
dvbs2acm (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the transmission format standard applied for
the startup stream. The start transport stream carries a
Network Information Table that the RCST uses for
acquiring the forward link signaling. Supported values
are:
-1: unspecified (automatic format acquisition is
assumed)
0: DVB-S (support of this value is mandatory if
DVB-S support is claimed)
1: DVB-S2 with CCM (support of this value is
mandatory if DVB-S2 CCM support is claimed)
2: DVB-S2 with VCM or ACM (support of this value is
mandatory if DVB-S2 ACM support is claimed)
This allows the RCST to discriminate between CCM and
VCM/ACM when selecting the forward link.
The support of automatic format selection is optional.
One or several of the other format selections must be
supported, according to the claimed SatLabs profile
support."
::={dvbRcsFwdStartEntry 5}
Combes, et al. Informational [Page 64]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsFwdStartRolloff OBJECT-TYPE
SYNTAX INTEGER {
autoRolloff (0),
rolloff020 (1),
rolloff025 (2),
rolloff035 (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the receive filter roll-off applied on the
start transponder. The start transponder carries a
Network Information Table that the RCST uses for
acquiring the forward link signaling.
Supported values are:
0: any (auto)
1: 0.20
2: 0.25
3: 0.35"
::={dvbRcsFwdStartEntry 6}
dvbRcsFwdStartSymbolRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 symbols/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the symbol rate on the start transponder
carrying a Network Information Table to which any RCST
shall trigger to acquire forward link. Its value shall
be given in multiples of 100 symbols/s."
::={dvbRcsFwdStartEntry 7}
dvbRcsFwdStartInnerFec OBJECT-TYPE
SYNTAX INTEGER {
autoFec (-1),
fecRate12 (0),
fecRate23 (1),
fecRate34 (2),
fecRate56 (3),
fecRate78 (4),
fecRate89 (5),
fecRate35 (6),
fecRate45 (7),
fecRate910 (8),
fecRate25 (9),
fecRate13 (10),
fecRate14 (11),
Combes, et al. Informational [Page 65]
RFC 5728 DVB-RCS MIB March 2010
noInnerCode (12)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the inner Forward Error Correction used on
the start transponder carrying a Network Information
Table to which any RCST shall trigger to acquire forward
link.
Supported values are:
autoFec (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (9),
fecRate1/3 (10),
fecRate1/4 (11),
noInnerCode (12)
The support of autoFec is optional."
::={dvbRcsFwdStartEntry 8}
dvbRcsFwdStartRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. It is not possible
to change values in a row of this table while the row is
active."
::={dvbRcsFwdStartEntry 9}
--==============================================================
-- dvbRcsFwdStatus sub-tree object types
--==============================================================
dvbRcsFwdStatusPopId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Population identifier applied at log-on:
0-65535: specific StartPopId
If the RCST was allowed to logon with any population,
Combes, et al. Informational [Page 66]
RFC 5728 DVB-RCS MIB March 2010
the RCST will report the base number of the announced
population ID indicated by the RCS Map Table linkage
descriptor used at logon."
::={dvbRcsFwdStatus 1}
dvbRcsFwdStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsFwdStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the current status of Forward Link
interfaces."
::={dvbRcsFwdStatus 2}
dvbRcsFwdStatusEntry OBJECT-TYPE
SYNTAX DvbRcsFwdStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the forward link status table. Each entry
is associated with a physical interface.
An RCST shall support at least one entry."
INDEX { dvbRcsFwdStatusIndex }
::= {dvbRcsFwdStatusTable 1}
DvbRcsFwdStatusEntry ::= SEQUENCE {
dvbRcsFwdStatusIndex Unsigned32,
dvbRcsFwdStatusIfReference Unsigned32,
dvbRcsFwdStatusNetId Unsigned32,
dvbRcsFwdStatusNetName
SnmpAdminString,
dvbRcsFwdStatusFormat INTEGER,
dvbRcsFwdStatusFrequency Unsigned32,
dvbRcsFwdStatusPolar INTEGER,
dvbRcsFwdStatusInnerFec INTEGER,
dvbRcsFwdStatusSymbolRate Unsigned32,
dvbRcsFwdStatusRolloff INTEGER,
dvbRcsFwdStatusModulation INTEGER,
dvbRcsFwdStatusFecFrame INTEGER,
dvbRcsFwdStatusPilot INTEGER,
dvbRcsFwdStatusBer Integer32,
dvbRcsFwdStatusCnr Integer32,
dvbRcsFwdStatusRxPower Integer32
}
dvbRcsFwdStatusIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS not-accessible
Combes, et al. Informational [Page 67]
RFC 5728 DVB-RCS MIB March 2010
STATUS current
DESCRIPTION
"Index of the forward link status table."
::={dvbRcsFwdStatusEntry 1}
dvbRcsFwdStatusIfReference OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cross reference to the interface table."
::={dvbRcsFwdStatusEntry 2}
dvbRcsFwdStatusNetId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interactive network identifier of the forward
link (from the RCS Map Table)."
::={dvbRcsFwdStatusEntry 3}
dvbRcsFwdStatusNetName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the interactive network of the forward
link (from the RCS Map Table)."
::={dvbRcsFwdStatusEntry 4}
dvbRcsFwdStatusFormat OBJECT-TYPE
SYNTAX INTEGER {
dvbs (0),
dvbs2ccm (1),
dvbs2acm (2),
reservedFormat (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the transmission format applied on the
forward link. Supported values are (from RCS Map Table):
0: DVB-S
1: DVB-S2 using CCM
2: DVB-S2 using VCM or ACM
3: reserved"
::={dvbRcsFwdStatusEntry 5}
Combes, et al. Informational [Page 68]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsFwdStatusFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 kHz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the frequency of the forward link. Its
value shall be given in multiples of 100 kHz."
::={dvbRcsFwdStatusEntry 6}
dvbRcsFwdStatusPolar OBJECT-TYPE
SYNTAX INTEGER {
linearHorizontal (0),
linearVertical (1),
circularLeft (2),
circularRight (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"2-bit field giving the polarization of the forward link
Supported values are (from RCS Map Table):
00: linear and horizontal
01: linear and vertical
10: circular left
11: circular right"
::={dvbRcsFwdStatusEntry 7}
dvbRcsFwdStatusInnerFec OBJECT-TYPE
SYNTAX INTEGER {
unknown (-1),
fecRate12 (0),
fecRate23 (1),
fecRate34 (2),
fecRate56 (3),
fecRate78 (4),
fecRate89 (5),
fecRate35 (6),
fecRate45 (7),
fecRate910 (8),
fecRate25 (9),
fecRate13 (10),
fecRate14 (11),
noInnerCode (12)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Combes, et al. Informational [Page 69]
RFC 5728 DVB-RCS MIB March 2010
"Specifies the inner Forward Error Correction used on
the forward link for transmission to the RCST.
Supported values are:
unknown (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (9),
fecRate1/3 (10),
fecRate1/4 (11),
noInnerCode (12)
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds. If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 8}
dvbRcsFwdStatusSymbolRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 symbols/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the symbol rate of the forward link.
Its value shall be given in multiples of 100 symbols/s."
::={dvbRcsFwdStatusEntry 9}
dvbRcsFwdStatusRolloff OBJECT-TYPE
SYNTAX INTEGER {
undefRolloff (0),
rolloff020 (1),
rolloff025 (2),
rolloff035 (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the roll-off applied on the forward
link.
Supported values are:
0: undefined
1: 0.20
Combes, et al. Informational [Page 70]
RFC 5728 DVB-RCS MIB March 2010
2: 0.25
3: 0.35"
::={dvbRcsFwdStatusEntry 10}
dvbRcsFwdStatusModulation OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
mBPSK (1),
mQPSK (2),
m8PSK (3),
m16APSK (4),
m32APSK (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the modulation on the forward link used for
transmission to the RCST. Supported values are:
0: unknown
1: BPSK
2: QPSK
3: 8PSK
4: 16APSK
5: 32APSK
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds.
If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 11}
dvbRcsFwdStatusFecFrame OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
shortframe (1),
longframe (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the frame length used on the forward link for
transmission to the RCST.
Supported values are:
0: Unknown
1: Short frame
2: Normal frame
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
Combes, et al. Informational [Page 71]
RFC 5728 DVB-RCS MIB March 2010
seconds.
If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 12}
dvbRcsFwdStatusPilot OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
pilotNotused (1),
pilotUsed (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether pilots are used on the forward link
for transmission to the RCST.
Supported values are:
0: Unknown
1: Pilots are not used
2: Pilots are used
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds.
If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 13}
dvbRcsFwdStatusBer OBJECT-TYPE
SYNTAX Integer32
UNITS "exponent of 10"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the RCST BER on the Forward Link in log10
units."
::={dvbRcsFwdStatusEntry 14}
dvbRcsFwdStatusCnr OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the RCST CNR on the Forward Link in 0.1 dB
units."
::={dvbRcsFwdStatusEntry 15}
dvbRcsFwdStatusRxPower OBJECT-TYPE
Combes, et al. Informational [Page 72]
RFC 5728 DVB-RCS MIB March 2010
SYNTAX Integer32
UNITS "0.1 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the power level of the forward link as
received at the IDU, in 0.1 dBm units."
DEFVAL { -500 }
::={dvbRcsFwdStatusEntry 16}
--==============================================================
-- dvbRcsRtnConfig sub-tree object types
--==============================================================
dvbRcsRtnConfigMaxEirp OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Max Equivalent Isotropic Radiated Power (EIRP) of the RCST,
given in resolution of 0.1 dBm and applied when the IDU
can, itself, set the necessary IDU TX output level, e.g.,
when using a BUC that has a power level detector and that
provides sufficient feedback to the IDU."
::= {dvbRcsRtnConfig 1}
dvbRcsRtnConfigDefIfLevel OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IDU TX output level applied in case the
dvbRcsRtnConfigMaxEirp cannot be used. The resolution
is 0.1 dBm and the accuracy is +/- 1 dBm."
::= {dvbRcsRtnConfig 2}
--==============================================================
-- dvbRcsRtnStatus sub-tree object types
--==============================================================
dvbRcsRtnStatusEbN0 OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The EbN0 value reported for the return link, referenced
to the regular SYNC burst transmission, in 0.1 dB
Combes, et al. Informational [Page 73]
RFC 5728 DVB-RCS MIB March 2010
units."
::= {dvbRcsRtnStatus 1}
dvbRcsRtnStatusSFDuration OBJECT-TYPE
SYNTAX Unsigned32 (250..7500)
UNITS "0.1 ms"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of the currently applied return link
superframe structure, in tenths of milliseconds."
::= {dvbRcsRtnStatus 2}
dvbRcsRtnStatusPayloadUnit OBJECT-TYPE
SYNTAX INTEGER {
unitATM (0),
unitMPEG (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if the payload unit used for the return link
is ATM or MPEG."
::= {dvbRcsRtnStatus 3}
--=============================================================
-- conformance information
--=============================================================
dvbRcsRcstGroups OBJECT IDENTIFIER ::=
{dvbRcsConformance 1}
dvbRcsRcstCompliances OBJECT IDENTIFIER ::=
{dvbRcsConformance 2}
--=============================================================
-- conformance statements
--=============================================================
dvbRcsRcstCompliance1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for DVB-RCS terminals that
are compliant with SatLabs System Recommendations.
Compliance is linked to the support by the terminal of
the options or features defined in the SatLabs System
Recommendations.
The supported options and features of a terminal are
declared in objects
dvbRcsSystemSatLabsOptionsDeclaration
and dvbRcsSystemSatLabsFeaturesDeclaration
Combes, et al. Informational [Page 74]
RFC 5728 DVB-RCS MIB March 2010
respectively."
MODULE -- this module
MANDATORY-GROUPS {dvbRcsRcstSystemGroup,
dvbRcsRcstNetworkGroup, dvbRcsRcstInstallGroup,
dvbRcsRcstQosGroup, dvbRcsRcstControlGroup,
dvbRcsRcstStateGroup, dvbRcsFwdConfigGroup,
dvbRcsFwdStatusGroup, dvbRcsRtnConfigGroup,
dvbRcsRtnStatusGroup}
GROUP dvbRcsRcstExtNetworkGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
networking management functionality. Such RCST is qualified
as supporting the EXTNETWORK feature, as defined in the
SatLabs System Recommendations."
GROUP dvbRcsRcstDnsGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the DNS
protocol. Such RCST is qualified as supporting the DNS
option, as defined in the SatLabs System Recommendations."
GROUP dvbRcsRcstExtInstallGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the
installation log file. Such RCST is qualified as supporting
the INSTALL_LOG feature, as defined in the SatLabs System
Recommendations."
GROUP dvbRcsRcstEnhancedClassifierGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
GROUP dvbRcsRcstMpegQosGroup
DESCRIPTION
"This group is mandatory for an RCST that supports MPEG
traffic bursts. Such RCST is qualified as supporting the
MPEG_TRF option, as defined in the SatLabs System
Recommendations."
GROUP dvbRcsRcstGlobalQosGroup
DESCRIPTION
"This group is mandatory for an RCST that supports global
Combes, et al. Informational [Page 75]
RFC 5728 DVB-RCS MIB March 2010
RCST QoS configuration data. Such RCST is qualified as
supporting the RCST_PARA feature, as defined in the SatLabs
System Recommendations."
GROUP dvbRcsRcstStrictQosGroup
DESCRIPTION
"This group is mandatory for an RCST that supports strict
channel ID dispatching. Such RCST is qualified as
supporting the CHID_STRICT option, as defined in the SatLabs
System Recommendations."
GROUP dvbRcsRcstExtControlGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
control management functionality. Such RCST is qualified as
supporting the EXTCONTROL feature, as defined in the SatLabs
System Recommendations."
GROUP dvbRcsRtnExtConfigGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
return link configuration management functionality. Such
RCST is qualified as supporting the EXTCONFIG feature, as
defined in the SatLabs System Recommendations."
GROUP dvbRcsRtnExtStatusGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
return link status report functionality. Such RCST is
qualified as supporting the EXTSTATUS feature, as defined in
the SatLabs System Recommendations."
GROUP dvbRcsRcstOduListGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the ODU
structural entities defined under dvbRcsOduTx, dvbRcsOduRx,
and dvbRcsOduAntenna. Such RCST is qualified as supporting
the ODULIST feature, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsSystemOduAntennaSize
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduAntennaGain
MIN-ACCESS read-only
Combes, et al. Informational [Page 76]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduSspa
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduTxType
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduRxType
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduRxBand
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduRxLO
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduTxLO
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsNetworkOamInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkOamInetAddress
SYNTAX InetAddress (SIZE(4))
Combes, et al. Informational [Page 77]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkLanInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkLanInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPrimaryDnsServerInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPrimaryDnsServerInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsSecondaryDnsServerInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsSecondaryDnsServerInetAddress
SYNTAX InetAddress (SIZE(4))
Combes, et al. Informational [Page 78]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkNccMgtInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkNccMgtInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassDscpLow
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
OBJECT dvbRcsPktClassDscpHigh
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
OBJECT dvbRcsPktClassDscpMarkValue
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
OBJECT dvbRcsPktClassSrcInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassSrcInetAddress
SYNTAX InetAddress (SIZE(4))
Combes, et al. Informational [Page 79]
RFC 5728 DVB-RCS MIB March 2010
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassDstInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassDstInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPhbName
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsPhbRequestClassAssociation
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsPhbMappingRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassName
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
Combes, et al. Informational [Page 80]
RFC 5728 DVB-RCS MIB March 2010
OBJECT dvbRcsRequestClassChanId
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassVccVpi
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassVccVci
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassPidPoolReference
MIN-ACCESS not-accessible
DESCRIPTION
"Read-only access required if the RCST supports MPEG traffic
bursts, according to the MPEG_TRF option, as defined in the
SatLabs System Recommendations. Create access only required
if the RCST also supports extended management support,
according to the SNMPMISC option, as defined in the SatLabs
System Recommendations."
OBJECT dvbRcsRequestClassCra
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassRbdcMax
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
Combes, et al. Informational [Page 81]
RFC 5728 DVB-RCS MIB March 2010
OBJECT dvbRcsRequestClassRbdcTimeout
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassVbdcMax
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassVbdcTimeout
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassVbdcMaxBackLog
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsPidValue
MIN-ACCESS not-accessible
DESCRIPTION
"Read-only access required if the RCST supports MPEG traffic
bursts, according to the MPEG_TRF option, as defined in the
SatLabs System Recommendations. Create access only required
if the RCST also supports extended management support,
according to the SNMPMISC option, as defined in the SatLabs
System Recommendations."
OBJECT dvbRcsPidPoolRowStatus
MIN-ACCESS not-accessible
DESCRIPTION
Combes, et al. Informational [Page 82]
RFC 5728 DVB-RCS MIB March 2010
"Read-only access required if the RCST supports MPEG traffic
bursts, according to the MPEG_TRF option, as defined in the
SatLabs System Recommendations. Create access only required
if the RCST also supports extended management support,
according to the SNMPMISC option, as defined in the SatLabs
System Recommendations."
::= {dvbRcsRcstCompliances 1}
--=============================================================
-- units of conformance
--=============================================================
--=============================================================
-- object groups for RCST system
--=============================================================
dvbRcsRcstSystemGroup OBJECT-GROUP
OBJECTS {
dvbRcsSystemMibRevision,
dvbRcsSystemSatLabsProfilesDeclaration,
dvbRcsSystemSatLabsOptionsDeclaration,
dvbRcsSystemSatLabsFeaturesDeclaration,
dvbRcsSystemLocation,
dvbRcsSystemOduAntennaSize,
dvbRcsSystemOduAntennaGain,
dvbRcsSystemOduSspa,
dvbRcsSystemOduTxType,
dvbRcsSystemOduRxType,
dvbRcsSystemOduRxBand,
dvbRcsSystemOduRxLO,
dvbRcsSystemOduTxLO,
dvbRcsTcpPep,
dvbRcsHttpPep
}
STATUS current
DESCRIPTION
"A collection of objects providing information
applicable for basic device management support."
::= {dvbRcsRcstGroups 1}
--=============================================================
-- object groups for RCST networking
--=============================================================
dvbRcsRcstNetworkGroup OBJECT-GROUP
OBJECTS {
dvbRcsNetworkOamInetAddressType,
dvbRcsNetworkOamInetAddress,
dvbRcsNetworkOamInetAddressPrefixLength,
Combes, et al. Informational [Page 83]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsNetworkLanInetAddressType,
dvbRcsNetworkLanInetAddress,
dvbRcsNetworkLanInetAddressPrefixLength,
dvbRcsNetworkConfigFileDownloadUrl,
dvbRcsNetworkConfigFileUploadUrl,
dvbRcsNetworkLogFileUploadUrl
}
STATUS current
DESCRIPTION
"A collection of objects providing basic networking
management support."
::= {dvbRcsRcstGroups 2}
dvbRcsRcstExtNetworkGroup OBJECT-GROUP
OBJECTS {
dvbRcsNetworkOamInetAddressAssign,
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType,
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress,
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressPrefixLength,
dvbRcsNetworkNccMgtInetAddressType,
dvbRcsNetworkNccMgtInetAddress,
dvbRcsNetworkNccMgtInetAddressPrefixLength
}
STATUS current
DESCRIPTION
"A collection of objects providing extended networking
management support."
::= {dvbRcsRcstGroups 3}
dvbRcsRcstDnsGroup OBJECT-GROUP
OBJECTS {
dvbRcsPrimaryDnsServerInetAddressType,
dvbRcsPrimaryDnsServerInetAddress,
dvbRcsPrimaryDnsServerInetAddressPrefixLength,
dvbRcsSecondaryDnsServerInetAddressType,
dvbRcsSecondaryDnsServerInetAddress,
dvbRcsSecondaryDnsServerInetAddressPrefixLength
}
STATUS current
DESCRIPTION
"A collection of objects providing DNS management
support."
::= {dvbRcsRcstGroups 4}
Combes, et al. Informational [Page 84]
RFC 5728 DVB-RCS MIB March 2010
--=============================================================
-- object groups for RCST installation
--=============================================================
dvbRcsRcstInstallGroup OBJECT-GROUP
OBJECTS {
dvbRcsInstallAntennaAlignmentState,
dvbRcsInstallCwFrequency,
dvbRcsInstallCwMaxDuration,
dvbRcsInstallCwPower,
dvbRcsInstallCoPolReading,
dvbRcsInstallXPolReading,
dvbRcsInstallCoPolTarget,
dvbRcsInstallXPolTarget,
dvbRcsInstallStandByDuration,
dvbRcsInstallTargetEsN0
}
STATUS current
DESCRIPTION
"A collection of objects providing information
applicable for basic installation support."
::= {dvbRcsRcstGroups 5}
dvbRcsRcstExtInstallGroup OBJECT-GROUP
OBJECTS {
dvbRcsNetworkInstallLogFileDownloadUrl,
dvbRcsNetworkInstallLogFileUploadUrl
}
STATUS current
DESCRIPTION
"A collection of objects providing extended device
installation support."
::= {dvbRcsRcstGroups 6}
--=============================================================
-- object groups for QoS
--=============================================================
dvbRcsRcstQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsPktClassDscpLow,
dvbRcsPktClassDscpHigh,
dvbRcsPktClassDscpMarkValue,
dvbRcsPktClassPhbAssociation,
dvbRcsPktClassRowStatus,
dvbRcsPhbName,
dvbRcsPhbRequestClassAssociation,
dvbRcsPhbMappingRowStatus,
Combes, et al. Informational [Page 85]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsRequestClassName,
dvbRcsRequestClassChanId,
dvbRcsRequestClassVccVpi,
dvbRcsRequestClassVccVci,
dvbRcsRequestClassCra,
dvbRcsRequestClassRbdcMax,
dvbRcsRequestClassRbdcTimeout,
dvbRcsRequestClassVbdcMax,
dvbRcsRequestClassVbdcTimeout,
dvbRcsRequestClassVbdcMaxBackLog,
dvbRcsRequestClassRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing basic access to QoS
configuration data."
::= {dvbRcsRcstGroups 7}
dvbRcsRcstEnhancedClassifierGroup OBJECT-GROUP
OBJECTS {
dvbRcsPktClassIpProtocol,
dvbRcsPktClassSrcInetAddressType,
dvbRcsPktClassSrcInetAddress,
dvbRcsPktClassSrcInetAddressPrefixLength,
dvbRcsPktClassDstInetAddressType,
dvbRcsPktClassDstInetAddress,
dvbRcsPktClassDstInetAddressPrefixLength,
dvbRcsPktClassSrcPortLow,
dvbRcsPktClassSrcPortHigh,
dvbRcsPktClassDstPortLow,
dvbRcsPktClassDstPortHigh,
dvbRcsPktClassVlanUserPri
}
STATUS current
DESCRIPTION
"A collection of objects providing support for
management of the enhanced classifier."
::= {dvbRcsRcstGroups 8}
dvbRcsRcstMpegQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsRequestClassPidPoolReference,
dvbRcsPidValue,
dvbRcsPidPoolRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing access to
Combes, et al. Informational [Page 86]
RFC 5728 DVB-RCS MIB March 2010
MPEG-related link QoS configuration data."
::= {dvbRcsRcstGroups 9}
dvbRcsRcstGlobalQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsQosGlobalRbdcMax,
dvbRcsQosGlobalVbdcMax,
dvbRcsQosGlobalVbdcMaxBackLog
}
STATUS current
DESCRIPTION
"A collection of objects providing access to global RCST
QoS configuration data."
::= {dvbRcsRcstGroups 10}
dvbRcsRcstStrictQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsQosChannelIdStrictDispatching
}
STATUS current
DESCRIPTION
"A collection of objects allowing management of strict
channel ID dispatching."
::= {dvbRcsRcstGroups 11}
--=============================================================
-- object groups for RCST control
--=============================================================
dvbRcsRcstControlGroup OBJECT-GROUP
OBJECTS {
dvbRcsCtrlRebootCommand,
dvbRcsCtrlUserTrafficDisable,
dvbRcsCtrlCwEnable,
dvbRcsCtrlDownloadFileCommand,
dvbRcsCtrlUploadFileCommand,
dvbRcsCtrlActivateConfigFileCommand,
dvbRcsCtrlRcstRxReacquire
}
STATUS current
DESCRIPTION
"A collection of objects allowing basic RCST control."
::= {dvbRcsRcstGroups 12}
dvbRcsRcstExtControlGroup OBJECT-GROUP
OBJECTS {
dvbRcsCtrlRcstTxDisable,
dvbRcsCtrlOduTxReferenceEnable,
Combes, et al. Informational [Page 87]
RFC 5728 DVB-RCS MIB March 2010
dvbRcsCtrlOduTxDCEnable,
dvbRcsCtrlOduRxDCEnable,
dvbRcsCtrlRcstLogonCommand,
dvbRcsCtrlRcstLogoffCommand
}
STATUS current
DESCRIPTION
"A collection of objects allowing extended RCST
control."
::= {dvbRcsRcstGroups 13}
--=============================================================
-- object groups for RCST state
--=============================================================
dvbRcsRcstStateGroup OBJECT-GROUP
OBJECTS {
dvbRcsRcstMode,
dvbRcsRcstFaultStatus,
dvbRcsRcstFwdLinkStatus,
dvbRcsRcstLogUpdated,
dvbRcsRcstCurrentSoftwareVersion,
dvbRcsRcstAlternateSoftwareVersion,
dvbRcsRcstActivatedConfigFileVersion,
dvbRcsRcstDownloadedConfigFileVersion
}
STATUS current
DESCRIPTION
"A collection of objects allowing access to RCST state."
::= {dvbRcsRcstGroups 14}
--=============================================================
-- object groups for forward link
--=============================================================
dvbRcsFwdConfigGroup OBJECT-GROUP
OBJECTS {
dvbRcsFwdStartPopId,
dvbRcsFwdStartFrequency,
dvbRcsFwdStartPolar,
dvbRcsFwdStartFormat,
dvbRcsFwdStartRolloff,
dvbRcsFwdStartSymbolRate,
dvbRcsFwdStartInnerFec,
dvbRcsFwdStartRowStatus
}
STATUS current
DESCRIPTION
Combes, et al. Informational [Page 88]
RFC 5728 DVB-RCS MIB March 2010
"A collection of objects providing basic start forward
link configuration support."
::= {dvbRcsRcstGroups 15}
dvbRcsFwdStatusGroup OBJECT-GROUP
OBJECTS {
dvbRcsFwdStatusPopId,
dvbRcsFwdStatusIfReference,
dvbRcsFwdStatusNetId,
dvbRcsFwdStatusNetName,
dvbRcsFwdStatusFormat,
dvbRcsFwdStatusFrequency,
dvbRcsFwdStatusPolar,
dvbRcsFwdStatusInnerFec,
dvbRcsFwdStatusSymbolRate,
dvbRcsFwdStatusRolloff,
dvbRcsFwdStatusModulation,
dvbRcsFwdStatusFecFrame,
dvbRcsFwdStatusPilot,
dvbRcsFwdStatusBer,
dvbRcsFwdStatusCnr,
dvbRcsFwdStatusRxPower
}
STATUS current
DESCRIPTION
"A collection of objects providing forward link status."
::= {dvbRcsRcstGroups 16}
--=============================================================
-- object groups for return link
--=============================================================
dvbRcsRtnConfigGroup OBJECT-GROUP
OBJECTS {
dvbRcsRtnConfigDefIfLevel
}
STATUS current
DESCRIPTION
"A collection of objects providing basic return link
configuration support."
::= {dvbRcsRcstGroups 17}
dvbRcsRtnExtConfigGroup OBJECT-GROUP
OBJECTS {
dvbRcsRtnConfigMaxEirp
}
STATUS current
DESCRIPTION
"A collection of objects providing extended return link
Combes, et al. Informational [Page 89]
RFC 5728 DVB-RCS MIB March 2010
configuration support."
::= {dvbRcsRcstGroups 18}
dvbRcsRtnStatusGroup OBJECT-GROUP
OBJECTS {
dvbRcsRtnStatusPayloadUnit
}
STATUS current
DESCRIPTION
"A collection of objects allowing access to return link
status."
::= {dvbRcsRcstGroups 19}
dvbRcsRtnExtStatusGroup OBJECT-GROUP
OBJECTS {
dvbRcsRcstRtnLinkStatus,
dvbRcsRtnStatusEbN0,
dvbRcsRtnStatusSFDuration
}
STATUS current
DESCRIPTION
"A collection of objects allowing access to extended
return link status."
::= {dvbRcsRcstGroups 20}
dvbRcsRcstOduListGroup OBJECT-GROUP
OBJECTS {
dvbRcsOduTxTypeDescription,
dvbRcsOduTxType,
dvbRcsOduRxTypeDescription,
dvbRcsOduRxType,
dvbRcsOduAntennaTypeDescription,
dvbRcsOduAntennaType
}
STATUS current
DESCRIPTION
"A collection of objects supporting flexible
selection of ODU devices."
::= {dvbRcsRcstGroups 21}
END
Combes, et al. Informational [Page 90]
RFC 5728 DVB-RCS MIB March 2010
5. Security Considerations
This MIB module relates to a system that allows end users to access a
private network or public Internet access. As such, improper
manipulation of the MIB objects represented by this MIB module may
result in denial of service to a large number of end users.
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read- create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o The use of the dvbRcsNetworkNccMgtInetAddress object to specify
management stations is considered only limited protection and does
not protect against attacks that spoof the management station's IP
address. The use of stronger mechanisms, such as SNMPv3 security,
should be considered, where possible.
o The dvbRcsSystemOdu objects, dvbRcsCtrlCwEnable,
dvbRcsRtnConfigMaxEirp, dvbRcsRtnConfigDefIfLevel objects, and
dvbRcsRcstInstall sub-tree can, if improperly or maliciously used,
lead to unwanted emissions or emission levels on the satellite
uplink, thereby resulting in potential degradation of the RCS
service or other services using the frequency band being used.
o The RCST may have its configuration file changed by the actions of
the management system using a combination of the following
objects: dvbRcsNetworkInstallLogFileDownloadUrl,
dvbRcsCtrlDownloadFileCommand,
dvbRcsCtrlActivateConfigFileCommand, or dvbRcsCtrlRebootCommand.
An improper configuration file download may result in substantial
vulnerabilities and the loss of the ability of the management
system to control the satellite terminal.
o Setting dvbRcsNetworkLogFileUploadUrl to a wrong address may
potentially impact debugging/troubleshooting efforts.
o Setting objects in dvbRcsPktClassTable could cause significant
changes to default traffic filtering on an RCST.
Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
Combes, et al. Informational [Page 91]
RFC 5728 DVB-RCS MIB March 2010
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o The dvbRcsNetworkNccMgtInetAddress object may provide sufficient
information for attackers to spoof management stations that have
management access to the device.
o The dvbRcsRcstCurrentSoftwareVersion object may provide hints as
to the software vulnerabilities of the RCST.
o The object dvbRcsNetworkOamInetAddress and the table
dvbRcsPktClassTable may provide clues for attacking the RCST and
other subscriber devices.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
6. IANA Considerations
The transmission and ifType numbers described in Section 3 have
already been assigned under the smi-numbers registry.
7. Acknowledgments
The authors thank Gorry Fairhurst for advice in the preparation of
this document and Bert Wijnen for his review comments.
The authors recognize this document is a collective effort of the
SatLabs Group (www.satlabs.org), in particular the many corrections
and suggestions brought by Juan Luis Manas.
Combes, et al. Informational [Page 92]
RFC 5728 DVB-RCS MIB March 2010
8. References
8.1. Normative References
[IANA] Internet Assigned Numbers Authority, "Internet Assigned
Numbers Authority", June 2008, <http://www.iana.org>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Structure of Management Information Version 2 (SMIv2)",
STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3289] Baker, F., Chan, K., and A. Smith, "Management
Information Base for the Differentiated Services
Architecture", RFC 3289, May 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC
3411, December 2002.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet Network
Addresses", RFC 4001, February 2005.
[RFC5017] McWalter, D., Ed., "MIB Textual Conventions for Uniform
Resource Identifiers (URIs)", RFC 5017, September 2007.
Combes, et al. Informational [Page 93]
RFC 5728 DVB-RCS MIB March 2010
8.2. Informative References
[ISO-MPEG] ISO/IEC DIS 13818-1:2000, "Information Technology;
Generic Coding of Moving Pictures and Associated Audio
Information Systems", International Organization for
Standardization (ISO).
[ITU-ATM] ITU-T Recommendation I.432 (all parts): "B-ISDN user-
network interface - Physical layer specification".
[ITU-AAL5] ITU-T Recommendation I.363-5 (1996): "B-ISDN ATM
Adaptation Layer specification: Type 5 AAL".
[ETSI-DAT] ETSI EN 301 192, "Digital Video Broadcasting (DVB); DVB
Specifications for Data Broadcasting", European
Telecommunications Standards Institute (ETSI).
[ETSI-DVBS] ETSI EN 301 421, "Digital Video Broadcasting (DVB);
Modulation and Coding for DBS satellite systems at 11/12
GHz", European Telecommunications Standards Institute
(ETSI).
[ETSI-DVBS2] ETSI EN 302 307, "Digital Video Broadcasting (DVB);
Second generation framing structure, channel coding and
modulation systems for Broadcasting, Interactive
Services, News Gathering and other broadband satellite
applications", European Telecommunications Standards
Institute (ETSI).
[ETSI-GSE] ETSI TS 102 606, "Digital Video Broadcasting (DVB);
Generic Stream Encapsulation (GSE) Protocol", European
Telecommunications Standards Institute (ETSI).
[ETSI-RCS] ETSI 301 790, "Digital Video Broadcasting (DVB);
Interaction Channel for Satellite Distribution Systems",
European Telecommunications Standards Institute (ETSI).
[ETSI-SI] ETSI EN 300 468, "Digital Video Broadcasting (DVB);
Specification for Service Information (SI) in DVB
Systems", European Telecommunications Standards
Institute (ETSI).
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[SATLABS] SatLabs System Recommendations,
<http://www.satlabs.org>.
Combes, et al. Informational [Page 94]
RFC 5728 DVB-RCS MIB March 2010
Authors' Addresses
Stephane Combes
ESTEC
European Space Agency
Keplerlaan 1
P.O. Box 299
2200 AG Noordwijk ZH
The Netherlands
EMail: stephane.combes@esa.int
URL: telecom.esa.int
Petter Chr. Amundsen
VeriSat AS
P.O Box 1
1330 Fornebu
Norway
EMail: pca@verisat.no
URL: www.verisat.no
Micheline Lambert
Advantech Satellite Networks
2341 boul. Alfred-Nobel
Saint-Laurent (Montreal)
H4S 2A9
Quebec, Canada
EMail: micheline.lambert@advantechamt.com
URL: www.advantechsatnet.com
Hans Peter Lexow
STM Norway
Vollsveien 21
1366 Lysaker
Norway
EMail: hlexow@stmi.com
URL: www.stmi.com
Combes, et al. Informational [Page 95]